Post on 30-May-2018
transcript
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 1/14
Presented By-Neeraj Kumar Singh
Rajesh Kumar Maurya
Vivek Kumar Tyagi
Sukhbir Singh
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 2/14
The primary objective of the project is to design along range fm transmitter
and receiver.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 3/14
The basic aim of designing a long range FMtransmitter and receiver is to transmit theFM signals to a long range and also to make itable for a receiver to tune very comfortably.
Our project will provide a receiver that willbe able to capture the FM signals clearly and
have a very long range of reception.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 4/14
The basic methodology which we will beusing during designing will be based on thedesigning of the layout first and after thatdesigning its PCB on Bakelite plate.
We will be using the basic resourcesavailable to us in the college for the
designing purpose.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 5/14
In the broader sense we have divided the
work into two major parts:• Designing of receiver section
• Designing of transmitter section
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 6/14
In 7th semester, as we have got 3 monthsbefore end semester exams, we will bedesigning receiver first.
In September, we will be collecting out allthe components available.
In October, we will be designing the basiclayout of the circuit on the PCB.
In November, we will complete the receiversection after installation of the components.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 7/14
As transmitter division is a bit difficult, sowe will look for it in 8th semester.
In February, we will be checking out the
components required for the designing. In March, we will design the basic layout of
the circuit on PCB.
After installation of components we will be
able to have a demo check of the transmitterby the end of April.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 8/14
We will be completing all the paper workssimultaneously and will be submitting it tothe deptt. and our project guide from timeto time.
A final synopsis cum report will be submittedby the mid of May along with the working
model.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 9/14
Basically we have divide the team into twogroups: One group will design the receiver section.
Another group will design the transmittersection.
Designing of the receiver will be done byNeeraj & Vivek.
Designing of transmitter will be done bySukhbir & Rajesh.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 10/14
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 11/14
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 12/14
The basic difficulty which will occur will beduring the designing of the transmitter.
Since the circuit of the transmitter is a bitbigger one, therefore its designing will be atough job.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 13/14
The major thing of concern is the availabilityof the components and its price.
The detailed knowledge of the total cost willbe made available to the deptt. By the endof this month.
We suppose to have a sponsorship of about40% of the project cost.
8/14/2019 long range fm tx and rx
http://slidepdf.com/reader/full/long-range-fm-tx-and-rx 14/14