Post on 30-May-2018
transcript
8/14/2019 Network Management Router Configuration
1/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 1
Design Problem Title/No. 2 Course Code: CAP-533
Course Instructor: Sr.Lect. Ginnia Kakkar Course Tutor( if applicable):
Date of Allotment : 10/11/09 Date of submission : 02-12-09
Students Roll number : RA3803A05 Section No.:A3803
Declaration:I declare that this assignment is my individual work. I have not
copied from any other students work or from any other source except wheredue acknowledgement is made explicitly in the text, nor has any part beenwritten for me by another person.
Students Sign: Balwinder Singh
Evaluators Comments:___________________________________________________
Marks obtained: ____________ out of __________________
8/14/2019 Network Management Router Configuration
2/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 2
PROBLEM
An organization Patterson Software Solutions Ltd need to set up a network for
its company. The company would be setting up a network to connect its
various departments using 4 routers:Router_HR with 2 hostsRouter_Production with 3 hosts
Router_MaintenanceCenter with 2 hostsRouter_Research with 2 hosts
The organization has decided to use Class A addressing with network address
16.0.0.0.The following are expectation which should be completed:
Configure the network using valid subnet mask. List out the IPaddresses that can be assigned to the hosts and the router interfaces.
Define Static routes for the network and verify with appropriatecommands that routes are configured properly. List out the routes
created.
Enable RIP protocol on the network to generate routing tabledynamically. Configure router with EIGRP on the network and list out the routes
created.
Can this network be configured now with OSPF routing protocol. If yes,configure the network and list out the routes generated.
8/14/2019 Network Management Router Configuration
3/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 3
SOLUTION
EXPECTATION-IConfigure the network using valid subnet mask. List out the IPaddresses that can be assigned to the hosts and the router
interfaces.
Since we know in the given problem there is a router having three hosts. Butit is not possible to connect three hosts to a router by default in simulator
Packet Tracer. To do this we first have to configure another interface port forthe router so that it can connect to three hosts at same time.
The following are the steps to configure the router:
1. Open packet tracer and drag a router.
2. Then connect three hosts to the router. But when you try to connect thethird host it will give the following error as shown in the print screen givenbelow.
8/14/2019 Network Management Router Configuration
4/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 4
3. Then click on the router and first switch it off from the button given on theright upper corner of the router backside diagram.
4. Then select third module and then drag and drop the Ethernet port to therouter blank place given in the back side of router it will look like as givenbelow.
8/14/2019 Network Management Router Configuration
5/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 5
5.After that the router will allow the connection for third host. Just as givenbelow.
8/14/2019 Network Management Router Configuration
6/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 6
Here is the solution for first expectation:1. Draw the network diagram by connecting the router with hosts as per
requirement.
2. Change the routers hostname for all routers just by following commandset s given below:Router>enRouter#config terminal
Router(config)#hostname Router_nameRouter(config)#^ZRouter#copy run start
Router#
Respective screen shots
8/14/2019 Network Management Router Configuration
7/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 7
3.Assign IP address to the interfaces of all the routers and set PORTSTATUS to ON and also set CLOCK RATE as given below.
Router_HR with 2 hosts
Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname Router_Production
Router_Production(config)#
Router_Production(config)#end%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router_Production#exitRouter_Production>
8/14/2019 Network Management Router Configuration
8/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 8
Router_HR>enableRouter_HR#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router_HR(config-if)#
Router_HR(config)#interface FastEthernet0/0Router_HR(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,changed state to upRouter_HR(config-if)#ip address 16.10.0.1 255.0.0.0
Router_HR(config-if)#ip address 16.10.0.1 255.255.240.0Router_HR(config-if)#Router_HR(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_HR#
Router_HR#configure terminalRouter_HR(config)#interface FastEthernet1/0Router_HR(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0,changed state to up
Router_HR(config-if)#ip address 16.20.0.1 255.255.240.0
Router_HR(config-if)#
Router_HR(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_HR#
Router_HR#configure terminalRouter_HR(config)#interface Serial2/0Router_HR(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to upno shutdownRouter_HR(config-if)#clock rate 128000Router_HR(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changedstate to upip address 16.30.0.1 255.255.240.0
Router_HR(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_HR#
8/14/2019 Network Management Router Configuration
9/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page 9
Respective screen shots
Router_Production with 3 hosts
Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname Router_Production
Router_Production(config)#Router_Production(config)#end%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#copy running-config startup-config
Destination filename [startup-config]?Building configuration...[OK]
Router_Production#exit
Router_Production>
Router_Production>enableRouter_Production#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_Production(config)#interface Serial2/0
8/14/2019 Network Management Router Configuration
10/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page10
Router_Production(config-if)#no shutdownRouter_Production(config-if)#clock rate 128000
Router_Production(config-if)#ip address 16.30.0.2 255.255.240.0
Router_Production(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
Router_Production#
Router_Production#configure terminal
Router_Production(config)#interface Serial3/0Router_Production(config-if)#no shutdownRouter_Production(config-if)#clock rate 128000
Router_Production(config-if)#ip address 16.70.0.1 255.255.240.0Router_Production(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#
Router_Production#configure terminalRouter_Production(config)#interface FastEthernet0/0Router_Production(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,changed state to upRouter_Production(config-if)#ip address 16.40.0.1 255.255.240.0
Router_Production(config-if)#
Router_Production(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#
Router_Production#configure terminalRouter_Production(config)#interface FastEthernet1/0Router_Production(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0,changed state to upRouter_Production(config-if)#ip address 16.50.0.1 255.255.240.0Router_Production(config-if)#Router_Production(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#
Router_Production#configure terminal
Router_Production(config)#interface FastEthernet6/0Router_Production(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet6/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0,
changed state to up
Router_Production(config-if)#ip address 16.60.0.1 255.255.240.0Router_Production(config-if)#
8/14/2019 Network Management Router Configuration
11/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page11
Router_Production(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_Production#
Respective screen shots
8/14/2019 Network Management Router Configuration
12/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page12
Router_MaintenanceCenter with 2 hosts
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router_MaintenanceCenterRouter_MaintenanceCenter(config)#
Router_MaintenanceCenter(config)#end
%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#copy running-config startup-configDestination filename [startup-config]?
Building configuration...[OK]Router_MaintenanceCenter#exitRouter_MaintenanceCenter>
Router_MaintenanceCenter>enableRouter_MaintenanceCenter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router_MaintenanceCenter(config)#interface Serial2/0Router_MaintenanceCenter(config-if)#no shutdownRouter_MaintenanceCenter(config-if)#clock rate 128000
Router_MaintenanceCenter(config-if)#ip address 16.70.0.2 255.255.240.0
Router_MaintenanceCenter(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#
Router_MaintenanceCenter#configure terminalRouter_MaintenanceCenter(config)#interface Serial3/0Router_MaintenanceCenter(config-if)#no shutdownRouter_MaintenanceCenter(config-if)#clock rate 128000
Router_MaintenanceCenter(config-if)#ip address 16.100.0.1255.255.240.0Router_MaintenanceCenter(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#
Router_MaintenanceCenter#configure terminalRouter_MaintenanceCenter(config)#interface FastEthernet0/0
Router_MaintenanceCenter(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,
changed state to upRouter_MaintenanceCenter(config-if)#ip address 16.80.0.1 255.255.240.0
Router_MaintenanceCenter(config-if)#
Router_MaintenanceCenter(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by console
8/14/2019 Network Management Router Configuration
13/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page13
Router_MaintenanceCenter#
Router_MaintenanceCenter#configure terminal
Router_MaintenanceCenter(config)#interface FastEthernet1/0
Router_MaintenanceCenter(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0,
changed state to up
Router_MaintenanceCenter(config-if)#ip address 16.90.0.1 255.255.240.0Router_MaintenanceCenter(config-if)#Router_MaintenanceCenter(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#
Respective screen shots
8/14/2019 Network Management Router Configuration
14/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page14
Router_Research with 2 hosts
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router_ResearchRouter_Research(config)#
Router_Research(config)#end
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Research#copy running-config startup-configDestination filename [startup-config]?
Building configuration...[OK]Router_Research#exitRouter_Research>
Router_Research>enableRouter_Research#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router_Research(config)#interface Serial2/0
Router_Research(config-if)#no shutdownRouter_Research(config-if)#clock rate 128000Router_Research(config-if)#ip address 16.70.0.2 255.255.240.0
Router_Research(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
Router_Research#
Router_Research#configure terminal
Router_Research(config)#interface FastEthernet0/0Router_Research(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,
changed state to upRouter_Research(config-if)#ip address 16.110.0.1 255.255.240.0Router_Research(config-if)#Router_Research(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_Research#
Router_Research#configure terminal
Router_Research(config)#interface FastEthernet1/0
Router_Research(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0,changed state to up
Router_Research(config-if)#ip address 16.120.0.1 255.255.240.0
Router_Research(config-if)#Router_Research(config-if)#^Z
8/14/2019 Network Management Router Configuration
15/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page15
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Research#
Respective screen shots
4.Assign IP address to all the Hosts as given below.Host 1:
8/14/2019 Network Management Router Configuration
16/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page16
Host 2:
Host 3:
Host 4:
8/14/2019 Network Management Router Configuration
17/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page17
Host 5:
Host 6:
Host 7:
8/14/2019 Network Management Router Configuration
18/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page18
Host 8:
Host 9:
5.After this configuration the network will look like as follows.
8/14/2019 Network Management Router Configuration
19/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page19
EXPECTATION-IIDefine Static routes for the network and verify with appropriatecommands that routes are configured properly. List out the routescreated.
In this expectation we have to define the static route for all routers in thenetwork. We also have to list out these routes. But there is one thing tobe noted that later on we also have to configure the network using
RIP, EIGRP and OSPF. So if we want that the protocols will workproperly then we should have to assign a value of admin distance
greater than 120 units. So the following steps are used to do this taskwhich is as follows:1. Definition of static routes for the network is as follows:
For this the following command set is used for every router individually.
The respective screen shots are given with the command set as follows:
Router_HR >enRouter_HR #
Router_HR #configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router_HR (config)#ip route 16.0.0.0 255.255.240.0 16.30.0.2 127Router_HR (config)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_HR #
Router_Production>enRouter_Production#
Router_Production#configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router_Production(config)#ip route 16.0.0.0 255.255.240.0 16.30.0.1 127Router_Production(config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#Router_Production>enRouter_Production#Router_Production#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_Production(config)#ip route 16.0.0.0 255.255.240.0 16.70.0.2 127Router_Production(config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production#
8/14/2019 Network Management Router Configuration
20/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page20
Router_MaintenanceCenter>enRouter_MaintenanceCenter#Router_MaintenanceCenter#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_MaintenanceCenter(config)#ip route 16.0.0.0 255.255.240.016.70.0.1 127Router_MaintenanceCenter(config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#Router_MaintenanceCenter>enRouter_MaintenanceCenter#
Router_MaintenanceCenter#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_MaintenanceCenter(config)#ip route 16.0.0.0 255.255.240.016.100.0.2 127
Router_MaintenanceCenter(config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_MaintenanceCenter#
Router_Research>enRouter_Research#
Router_Research#configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router_Research(config)#ip route 16.0.0.0 255.255.240.0 16.30.0.2 127Router_Research(config)#^Z
8/14/2019 Network Management Router Configuration
21/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page21
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Research#
2. To see whether the routes are properly defined or not and also to see theroutes created the following command set is used for every routerindividually. In output of the command execution S indicate the static
route for the router to the network and C indicate the direct connection
with the router.Router_HR
Router_HR>en
Router_HR#sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 4 subnetsS 16.0.0.0 [127/0] via 16.30.0.2
C 16.10.0.0 is directly connected, FastEthernet0/0C 16.20.0.0 is directly connected, FastEthernet1/0C 16.30.0.0 is directly connected, Serial2/0Router_HR#
8/14/2019 Network Management Router Configuration
22/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page22
Router_Production
Router_Production >enRouter_Production #sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 5 subnetsS 16.0.0.0 [127/0] via 16.30.0.1
[127/0] via 16.70.0.2C 16.30.0.0 is directly connected, Serial2/0
C 16.40.0.0 is directly connected, FastEthernet0/0C 16.50.0.0 is directly connected, FastEthernet1/0C 16.60.0.0 is directly connected, FastEthernet1/0
C 16.70.0.0 is directly connected, Serial3/0Router_Production#
8/14/2019 Network Management Router Configuration
23/48
8/14/2019 Network Management Router Configuration
24/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page24
Router_Research
Router_Research>enRouter_Research #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 4 subnets
S 16.0.0.0 [127/0] via 16.100.0.1C 16.100.0.0 is directly connected, Serial2/0
C 16.110.0.0 is directly connected, FastEthernet0/0C 16.120.0.0 is directly connected, FastEthernet1/0
Router_Research #
8/14/2019 Network Management Router Configuration
25/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page25
3. Then verify the static routes defined properly just use the PINGCOMMAND with respective screen shots as follows.PC>ping 16.20.0.5
Pinging 16.20.0.5 with 32 bytes of data:
Reply from 16.20.0.5: bytes=32 time=22ms TTL=124Reply from 16.20.0.5: bytes=32 time=15ms TTL=124
Reply from 16.20.0.5: bytes=32 time=28ms TTL=124Reply from 16.20.0.5: bytes=32 time=21ms TTL=124
Ping statistics for 16.20.0.5:Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:Minimum = 15ms, Maximum = 28ms, Average = 21ms
PC>
8/14/2019 Network Management Router Configuration
26/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page26
EXPECTATION-IIIEnable RIP protocol on the network to generate routing tabledynamically.To configure the network using RIP (Routing Information Protocol) just follow
the steps given below:
1. Definition of RIP routes for the network is as follows:For this the following command set is used for every router individually.The respective screen shots are given with the command set as follows:
Router_HRRouter_HR >enRouter_HR #
Router_HR #configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_HR (config)#router ripRouter_HR (config)#network 16.0.0.0
Router_HR (config)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_HR #
Router_Production
Router_Production >en
Router_Production #Router_Production #configure terminal
Enter configuration commands, one per line. End with CNTL/Z.Router_Production (config)#router rip
Router_Production (config)#network 16.0.0.0Router_Production (config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production #
8/14/2019 Network Management Router Configuration
27/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page27
Router_MaintenanceCenter
Router_MaintenanceCenter >en
Router_MaintenanceCenter #
Router_MaintenanceCenter #configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router_MaintenanceCenter (config)#router rip
Router_MaintenanceCenter (config)#network 16.0.0.0Router_MaintenanceCenter (config)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_MaintenanceCenter #
Router_Research
Router_Research >en
Router_Research #Router_Research #configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router_Research (config)#router ripRouter_Research (config)#network 16.0.0.0
Router_Research (config)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_Research #
2. To see whether the routes are properly defined or not and also to see theroutes created the following command set is used for every routerindividually. In output of the command execution S indicate the staticroute, R indicate the RIP route for the router to the network and C
indicate the direct connection with the router.Router_HR
Router_HR #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
8/14/2019 Network Management Router Configuration
28/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page28
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnetsS 16.0.0.0 [127/0] via 16.30.0.2
C 16.10.0.0 is directly connected, FastEthernet0/0C 16.20.0.0 is directly connected, FastEthernet1/0C 16.30.0.0 is directly connected, Serial2/0R 16.40.0.0 [120/1] via 16.30.0.2, 00:00:01, Serial2/0
R 16.50.0.0 [120/1] via 16.30.0.2, 00:00:01, Serial2/0R 16.60.0.0 [120/1] via 16.30.0.2, 00:00:01, Serial2/0R 16.70.0.0 [120/1] via 16.30.0.2, 00:00:01, Serial2/0R 16.80.0.0 [120/2] via 16.30.0.2, 00:00:01, Serial2/0R 16.90.0.0 [120/2] via 16.30.0.2, 00:00:01, Serial2/0
R 16.100.0.0 [120/2] via 16.30.0.2, 00:00:01, Serial2/0R 16.110.0.0 [120/3] via 16.30.0.2, 00:00:01, Serial2/0R 16.120.0.0 [120/3] via 16.30.0.2, 00:00:01, Serial2/0
Router_HR #
8/14/2019 Network Management Router Configuration
29/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page29
Router_Production
Router_Production #sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnets
S 16.0.0.0 [127/0] via 16.30.0.1
[127/0] via 16.70.0.2R 16.10.0.0 [120/1] via 16.30.0.1, 00:00:12, Serial2/0R 16.20.0.0 [120/1] via 16.30.0.1, 00:00:12, Serial2/0
C 16.30.0.0 is directly connected, Serial2/0C 16.40.0.0 is directly connected, FastEthernet0/0C 16.50.0.0 is directly connected, FastEthernet1/0C 16.60.0.0 is directly connected, FastEthernet6/0
C 16.70.0.0 is directly connected, Serial3/0R 16.80.0.0 [120/1] via 16.70.0.2, 00:00:16, Serial3/0R 16.90.0.0 [120/1] via 16.70.0.2, 00:00:16, Serial3/0R 16.100.0.0 [120/1] via 16.70.0.2, 00:00:16, Serial3/0
R 16.110.0.0 [120/2] via 16.70.0.2, 00:00:16, Serial3/0R 16.120.0.0 [120/2] via 16.70.0.2, 00:00:16, Serial3/0
8/14/2019 Network Management Router Configuration
30/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page30
Router_Production #
Router_MaintenanceCenter
Router_MaintenanceCenter #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnetsS 16.0.0.0 [127/0] via 16.70.0.1
[127/0] via 16.100.0.2
R 16.10.0.0 [120/2] via 16.70.0.1, 00:00:16, Serial2/0R 16.20.0.0 [120/2] via 16.70.0.1, 00:00:16, Serial2/0R 16.30.0.0 [120/1] via 16.70.0.1, 00:00:16, Serial2/0R 16.40.0.0 [120/1] via 16.70.0.1, 00:00:16, Serial2/0
R 16.50.0.0 [120/1] via 16.70.0.1, 00:00:16, Serial2/0R 16.60.0.0 [120/1] via 16.70.0.1, 00:00:16, Serial2/0C 16.70.0.0 is directly connected, Serial2/0
C 16.80.0.0 is directly connected, FastEthernet0/0C 16.90.0.0 is directly connected, FastEthernet1/0
8/14/2019 Network Management Router Configuration
31/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page31
C 16.100.0.0 is directly connected, Serial3/0R 16.110.0.0 [120/1] via 16.100.0.2, 00:00:01, Serial3/0
R 16.120.0.0 [120/1] via 16.100.0.2, 00:00:01, Serial3/0
Router_MaintenanceCenter #
Router_Research
Router_Research#sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnets
S 16.0.0.0 [1/0] via 16.100.0.1R 16.10.0.0 [120/3] via 16.100.0.1, 00:00:10, Serial2/0R 16.20.0.0 [120/3] via 16.100.0.1, 00:00:10, Serial2/0R 16.30.0.0 [120/2] via 16.100.0.1, 00:00:10, Serial2/0
R 16.40.0.0 [120/2] via 16.100.0.1, 00:00:10, Serial2/0R 16.50.0.0 [120/2] via 16.100.0.1, 00:00:10, Serial2/0
R 16.60.0.0 [120/2] via 16.100.0.1, 00:00:10, Serial2/0R 16.70.0.0 [120/1] via 16.100.0.1, 00:00:10, Serial2/0
8/14/2019 Network Management Router Configuration
32/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page32
R 16.80.0.0 [120/1] via 16.100.0.1, 00:00:10, Serial2/0R 16.90.0.0 [120/1] via 16.100.0.1, 00:00:10, Serial2/0
C 16.100.0.0 is directly connected, Serial2/0
C 16.110.0.0 is directly connected, FastEthernet0/0
C 16.120.0.0 is directly connected, FastEthernet1/0
Router_Research#
3. Then verify the RIP routes defined properly just use the PINGCOMMAND with respective screen shots as follows.
8/14/2019 Network Management Router Configuration
33/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page33
EXPECTATION-IVConfigure router with EIGRP on the network and list out the routescreatedTo configure the network using EIGRP (Enhanced Interior Gateway Protocol)
just follow the steps given below:
1. Definition of EIGRP routes for the network is as follows:For this the following command set is used for every router individually.The respective screen shots are given with the command set as follows:
Router_HR
Router_HR >en
Router_HR #config t
Enter configuration commands, one per line. End with CNTL/Z.Router_HR (config)#router eigrp 16Router_HR (config-router)#network 16.0.0.0
Router_HR (config-router)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_HR #
Router_Production
Router_Production >en
Router_Production #config tEnter configuration commands, one per line. End with CNTL/Z.Router_Production (config)#router eigrp 16
Router_Product(config-router)#network 16.0.0.0Router_Product(config-router)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production #
Router_MaintenanceCenter
Router_MaintenanceCenter >en
8/14/2019 Network Management Router Configuration
34/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page34
Router_MaintenanceCenter #config tEnter configuration commands, one per line. End with CNTL/Z.
Router_MaintenanceCen(config)#router eigrp 16
Router_Mainten(config-router)#network 16.0.0.0
Router_Mainten(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 16: Neighbor 16.70.0.1 (Serial2/0) is up:new adjacency^Z
%SYS-5-CONFIG_I: Configured from console by console
Router_MaintenanceCenter #
Router_Research
Router_Research>enRouter_Research#config tEnter configuration commands, one per line. End with CNTL/Z.
Router_Research(config)#router eigrp 16Router_Researc(config-router)#network 16.0.0.0Router_Researc(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Research#
2. To see whether the routes are properly defined or not and also to see theroutes created the following command set is used for every routerindividually. In output of the command execution S indicate the staticroute, D indicate the EIGRP route for the router to the network and Cindicate the direct connection with the router.
Router_HR
Router_HR #sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
8/14/2019 Network Management Router Configuration
35/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page35
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 12 subnets
C 16.10.0.0 is directly connected, FastEthernet0/0
C 16.20.0.0 is directly connected, FastEthernet1/0C 16.30.0.0 is directly connected, Serial2/0D 16.40.0.0 [90/20514560] via 16.30.0.2, 00:03:36, Serial2/0
D 16.50.0.0 [90/20514560] via 16.30.0.2, 00:03:36, Serial2/0D 16.60.0.0 [90/20514560] via 16.30.0.2, 00:03:36, Serial2/0D 16.70.0.0 [90/21024000] via 16.30.0.2, 00:03:36, Serial2/0D 16.80.0.0 [90/21026560] via 16.30.0.2, 00:02:24, Serial2/0
D 16.90.0.0 [90/21026560] via 16.30.0.2, 00:02:24, Serial2/0D 16.100.0.0 [90/21536000] via 16.30.0.2, 00:02:24, Serial2/0D 16.110.0.0 [90/21538560] via 16.30.0.2, 00:00:53, Serial2/0D 16.120.0.0 [90/21538560] via 16.30.0.2, 00:00:53, Serial2/0Router_HR #
Router_Production
Router_Production #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
8/14/2019 Network Management Router Configuration
36/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page36
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnets
S 16.0.0.0 [127/0] via 16.70.0.2[127/0] via 16.30.0.1
D 16.10.0.0 [90/20514560] via 16.30.0.1, 00:04:55, Serial2/0
D 16.20.0.0 [90/20514560] via 16.30.0.1, 00:04:55, Serial2/0C 16.30.0.0 is directly connected, Serial2/0C 16.40.0.0 is directly connected, FastEthernet0/0C 16.50.0.0 is directly connected, FastEthernet1/0
C 16.60.0.0 is directly connected, FastEthernet6/0C 16.70.0.0 is directly connected, Serial3/0D 16.80.0.0 [90/20514560] via 16.70.0.2, 00:03:44, Serial3/0D 16.90.0.0 [90/20514560] via 16.70.0.2, 00:03:44, Serial3/0D 16.100.0.0 [90/21024000] via 16.70.0.2, 00:03:44, Serial3/0
D 16.110.0.0 [90/21026560] via 16.70.0.2, 00:02:13, Serial3/0D 16.120.0.0 [90/21026560] via 16.70.0.2, 00:02:13, Serial3/0Router_Production #
8/14/2019 Network Management Router Configuration
37/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page37
Router_MaintenanceCenter
Router_MaintenanceCenter #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnets
S 16.0.0.0 [127/0] via 16.100.0.2[127/0] via 16.70.0.1
D 16.10.0.0 [90/21026560] via 16.70.0.1, 00:04:40, Serial2/0D 16.20.0.0 [90/21026560] via 16.70.0.1, 00:04:40, Serial2/0D 16.30.0.0 [90/21024000] via 16.70.0.1, 00:04:40, Serial2/0
D 16.40.0.0 [90/20514560] via 16.70.0.1, 00:04:40, Serial2/0D 16.50.0.0 [90/20514560] via 16.70.0.1, 00:04:40, Serial2/0D 16.60.0.0 [90/20514560] via 16.70.0.1, 00:04:40, Serial2/0
C 16.70.0.0 is directly connected, Serial2/0
C 16.80.0.0 is directly connected, FastEthernet1/0
C 16.90.0.0 is directly connected, FastEthernet0/0C 16.100.0.0 is directly connected, Serial3/0D 16.110.0.0 [90/20514560] via 16.100.0.2, 00:03:10, Serial3/0
D 16.120.0.0 [90/20514560] via 16.100.0.2, 00:03:10, Serial3/0Router_MaintenanceCenter #
8/14/2019 Network Management Router Configuration
38/48
8/14/2019 Network Management Router Configuration
39/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page39
Router_Research#
3. Then verify the EIGRP routes defined properly just use the PINGCOMMAND with respective screen shots as follows.
PC>ping 16.120.0.5
Pinging 16.120.0.5 with 32 bytes of data:
Reply from 16.120.0.5: bytes=32 time=21ms TTL=124
Reply from 16.120.0.5: bytes=32 time=19ms TTL=124Reply from 16.120.0.5: bytes=32 time=20ms TTL=124Reply from 16.120.0.5: bytes=32 time=18ms TTL=124
Ping statistics for 16.120.0.5:Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:Minimum = 18ms, Maximum = 21ms, Average = 19ms
PC>
8/14/2019 Network Management Router Configuration
40/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page40
EXPECTATION-VCan this network be configured now with OSPF routing protocol. Ifyes, configure the network and list out the routes generated.
To configure the network using OSPF(Open Shortest Path first) we first have
to disable the EIGRP protocols service because EIGRP in this
network has the minimum value of admin distance i.e. equal to 90which is less than the admin distance of RIP(120) and the Admindistance assigned to static route(127). It also less than the admin
distance of the OSPF (110). So for proper working of OSPF we have todisable the EIGRP protocol. The following command set will be used
individually on each router for the disable operation of EIGRP.
Router_Production >en
Router_Production #config tEnter configuration commands, one per line. End with CNTL/Z.Router_Production (config)#no router eigrp 16
Router_Production (config)#^Z
%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production #
After this just follow the steps given below:
1. Definition of OSPF routes for the network is as follows:For this the following command set is used for every router individually.The respective screen shots are given with the command set as follows:
Router_HR
Router_HR #Router_Production #config tEnter configuration commands, one per line. End with CNTL/Z.
Router_HR (config)#router ospf 100
Router_HR (config-router)#network 16.0.0.0 0.255.255.255 area 7Router_HR (config-router)#^Z
8/14/2019 Network Management Router Configuration
41/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page41
%SYS-5-CONFIG_I: Configured from console by consoleRouter_HR #
Router_Production
Router_Production #Router_Production #config tEnter configuration commands, one per line. End with CNTL/Z.Router_Production (config)#router ospf 100Router_Product(config-router)#network 16.0.0.0 0.255.255.255 area 7
Router_Product(config-router)#^Z%SYS-5-CONFIG_I: Configured from console by consoleRouter_Production #
Router_Maintenancecenter
Router_MaintenanceCenter #Router_MaintenanceCenter #config tEnter configuration commands, one per line. End with CNTL/Z.
Router_MaintenanceCen(config)#router ospf 100Router_Mainten(config-router)#network 16.0.0.0 0.255.255.255 area 7Router_Mainten(config-router)#^Z%SYS-5-CONFIG_I: Configured from console by console
Router_MaintenanceCenter #
8/14/2019 Network Management Router Configuration
42/48
8/14/2019 Network Management Router Configuration
43/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page43
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 12 subnets
C 16.10.0.0 is directly connected, FastEthernet0/0C 16.20.0.0 is directly connected, FastEthernet1/0C 16.30.0.0 is directly connected, Serial2/0
O 16.40.0.0 [110/782] via 16.30.0.2, 00:06:45, Serial2/0O 16.50.0.0 [110/782] via 16.30.0.2, 00:06:45, Serial2/0O 16.60.0.0 [110/782] via 16.30.0.2, 00:06:45, Serial2/0O 16.70.0.0 [110/1562] via 16.30.0.2, 00:06:45, Serial2/0
O 16.80.0.0 [110/1563] via 16.30.0.2, 00:04:39, Serial2/0O 16.90.0.0 [110/1563] via 16.30.0.2, 00:04:39, Serial2/0O 16.100.0.0 [110/2343] via 16.30.0.2, 00:04:39, Serial2/0O 16.110.0.0 [110/2344] via 16.30.0.2, 00:01:07, Serial2/0O 16.120.0.0 [110/2344] via 16.30.0.2, 00:01:07, Serial2/0
Router_HR #
Router_Production
Router_Production #Router_Production #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
8/14/2019 Network Management Router Configuration
44/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page44
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnetsS 16.0.0.0 [127/0] via 16.70.0.2
[127/0] via 16.30.0.1
O 16.10.0.0 [110/782] via 16.30.0.1, 00:07:50, Serial2/0O 16.20.0.0 [110/782] via 16.30.0.1, 00:07:50, Serial2/0C 16.30.0.0 is directly connected, Serial2/0C 16.40.0.0 is directly connected, FastEthernet0/0
C 16.50.0.0 is directly connected, FastEthernet1/0C 16.60.0.0 is directly connected, FastEthernet6/0C 16.70.0.0 is directly connected, Serial3/0O 16.80.0.0 [110/782] via 16.70.0.2, 00:05:54, Serial3/0O 16.90.0.0 [110/782] via 16.70.0.2, 00:05:54, Serial3/0
O 16.100.0.0 [110/1562] via 16.70.0.2, 00:05:54, Serial3/0O 16.110.0.0 [110/1563] via 16.70.0.2, 00:02:12, Serial3/0O 16.120.0.0 [110/1563] via 16.70.0.2, 00:02:12, Serial3/0
Router_Production #
Router_MaintenanceCenter
8/14/2019 Network Management Router Configuration
45/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page45
Router_MaintenanceCenter #
Router_MaintenanceCenter #sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnetsS 16.0.0.0 [127/0] via 16.100.0.2
[127/0] via 16.70.0.1O 16.10.0.0 [110/1563] via 16.70.0.1, 00:07:17, Serial2/0O 16.20.0.0 [110/1563] via 16.70.0.1, 00:07:17, Serial2/0O 16.30.0.0 [110/1562] via 16.70.0.1, 00:07:17, Serial2/0O 16.40.0.0 [110/782] via 16.70.0.1, 00:07:17, Serial2/0
O 16.50.0.0 [110/782] via 16.70.0.1, 00:07:17, Serial2/0O 16.60.0.0 [110/782] via 16.70.0.1, 00:07:17, Serial2/0C 16.70.0.0 is directly connected, Serial2/0
C 16.80.0.0 is directly connected, FastEthernet1/0
C 16.90.0.0 is directly connected, FastEthernet0/0
C 16.100.0.0 is directly connected, Serial3/0O 16.110.0.0 [110/782] via 16.100.0.2, 00:03:47, Serial3/0O 16.120.0.0 [110/782] via 16.100.0.2, 00:03:47, Serial3/0
Router_MaintenanceCenter #
8/14/2019 Network Management Router Configuration
46/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page46
Router_Research
Router_Research#Router_Research#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route
Gateway of last resort is not set
16.0.0.0/20 is subnetted, 13 subnetsS 16.0.0.0 [1/0] via 16.100.0.1O 16.10.0.0 [110/2344] via 16.100.0.1, 00:06:05, Serial2/0
O 16.20.0.0 [110/2344] via 16.100.0.1, 00:06:05, Serial2/0
O 16.30.0.0 [110/2343] via 16.100.0.1, 00:06:05, Serial2/0O 16.40.0.0 [110/1563] via 16.100.0.1, 00:06:05, Serial2/0O 16.50.0.0 [110/1563] via 16.100.0.1, 00:06:05, Serial2/0O 16.60.0.0 [110/1563] via 16.100.0.1, 00:06:05, Serial2/0
O 16.70.0.0 [110/1562] via 16.100.0.1, 00:06:05, Serial2/0O 16.80.0.0 [110/782] via 16.100.0.1, 00:06:05, Serial2/0
O 16.90.0.0 [110/782] via 16.100.0.1, 00:06:05, Serial2/0C 16.100.0.0 is directly connected, Serial2/0
8/14/2019 Network Management Router Configuration
47/48
Network Management RA3803A05 CAP-553/Design Problem-2
Page47
C 16.110.0.0 is directly connected, FastEthernet0/0C 16.120.0.0 is directly connected, FastEthernet1/0
Router_Research#
3. Then verify the OSPF routes defined properly just use the PINGCOMMAND with respective screen shots as follows.
PC>ping 16.110.0.5
Pinging 16.110.0.5 with 32 bytes of data:
Reply from 16.110.0.5: bytes=32 time=23ms TTL=124Reply from 16.110.0.5: bytes=32 time=24ms TTL=124Reply from 16.110.0.5: bytes=32 time=20ms TTL=124
Reply from 16.110.0.5: bytes=32 time=22ms TTL=124
Ping statistics for 16.110.0.5:Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:Minimum = 20ms, Maximum = 24ms, Average = 22ms
PC>
8/14/2019 Network Management Router Configuration
48/48
Network Management RA3803A05 CAP-553/Design Problem-2