OPEN THE NOKIA BTS MANAGER

CLICK CONNECT

WCDMA BTS IS GETTING CONNECTED

FRGC NOT DETECTED CHECK THE HARDWARE AND OPTIC FIBER IS CONNECTED PROPERLY. MOSTLY FIBER OR PATCH CORD IS FAULTY IN THIS CASE

SELECT THE REQUIRED CONFIGURATION FOR COMMISSIONING THE WCDMA BTS1. BTS SITE: FOR COMPLETE BTS AND TRS COMMISSIONING.2. BTS ONLY: FOR ONLY BTS CONFIGURATION.3. TRS ONLY: FOR TRS CONFIGURATION.4. TEMPLET : 5. PLANNED : IF THE BTS SCRIPT IS PREMADE.6. MANUAL : TO CONFIGURE THE BTS ON SITE.7. RECONFIGURING: IF THE BTS IS CONFIGURED AND NEED TO CHANGE THE FEW PARAMETERS.

1. FILL THE SITE INFORMATION.

2. ADD BTS ID – BTS ID CAN BE OBTAINED FROM THE NETWORK PLANNER OR THE SITE ID CAN BE THE BTS ID – (WHERE 3 REPRESENTS 3G AND FOLLOWING NUMBERS REPRESENT THE BTS ID.

3. A2EA WILL APEAR AUTOMATICALLY AS SOON THE BTS ID FILLED.

4. IP ADDRESS: IP ADDRESS CAN BE OBTAINED FROM THE NETWORK OPERATOR OR FROM BSC.

5. CLICK NEXT AFTER FILLING ALL THE DATA.

MARK IF IN USE AS PER THE AVIALABLE E1 – 1ST E1 : PRIMARY – IMA33.

2ND E1 : SECONDARY – IMA33

TRAFFIC DESCRIPTOR:

TRAFFIC DESCRIPTOR WITH 2E1

CBR CBR CBR CBR CBR CBR CBR

  CNBAP DNBAP AAL2SIG USERPLANE   DCN DCN

VP1 VC 42 VC52 VC 62 VC 72   VP2 VC32

8790 150 300 150 8190   120 120

TRAFFIC DESCRIPTOR WITH 1E1

CBR CBR CBR CBR CBR UBR UBR

  CNBAP DNBAP AAL2SIG USERPLANE   DCN DCN

VP1=1 VC 42 VC52 VC 62 VC 72   VP2 VC32

4377 80 150 80 4067   151 151

NOTE: TRAFFIC DESCRIPTOR DATA CAN BE OBTAINED FROM NETWORK OPERATOR OR FROM BSC.

TRAFFIC DESCRIPTOR CAN ALSO BE OBTAINED FROM NETWORK OPRATOR

DEFINING IUB

ATM Virtual Path Towards RNC FOR 2E1 FOR 1E1

ATM INTERFACE IMA Group 33 IMA Group 33

VPI 32 32

VP TRADE VP1-CBR.1/8790 VP1-CBR.1/4377

Common NBAP

VCI 42 42

VC TRADE CNBAP-CBR.1/150 CNBAP-CBR.1/80

Dedicated NBAP

VCI 52 52

VC TRADE DNBAP-CBR.1/300 DNBAP-CBR.1/150

AAL2 Signalling

VCI 62 62

VC TRADE AAL2SIG-CBR.1/150 AAL2SIG-CBR.1/80

AAL2 User Paths

VCI 72 72

TRADE VC32-CBR.1/120 VC32-CBR.1/151

1. DEFINE BTS SETTINGS2. REAL TILT : IF USED. (GET THE IP ADDRESS FOR REAL TILT FROM NETWORK OPERATOR3. MODULE LOCATION : DEFINE THE LOCATION OF THE MODULE WITH MODULE ID 3218 WHERE 3 REPRESENTS 3G AND 218 REPRESENTS THE SITE ID. NOTE: DIFFERENT MODULES CAN BE OF SAME ID.4. PASSIVE UNIT : DEFINE THE SL.NO FOR THE CABINET ETC.

DEFINE ANT ID 32181. WHERE 3 REPRESENTS 3G,

218 REPRESENTS SITE ID AND 1 REPRESENTS

SECTOR NUMBER

DEFINE THE ANTENNA PORT SETTING FOR SECTOR 1

DEFINE ANT ID 32182. WHERE 3 REPRESENTS 3G,

218 REPRESENTS SITE ID AND 2 REPRESENTS

SECTOR NUMBER

DEFINE THE ANTENNA PORT SETTING FOR SECTOR 2

DEFINE ANT ID 32183. WHERE 3 REPRESENTS 3G,

218 REPRESENTS SITE ID AND 3 REPRESENTS

SECTOR NUMBER

DEFINE THE ANTENNA PORT SETTING FOR SECTOR 3

CLICK NEXT

DEFINE IF MHA IS IN USE

DEFINE ALARMS IF CONNECTED TO THE WCDMA BTS

COMMISSIONING IS DONE SEND THE PARAMETER TO THE BTS

SAVE THE PARAMETER TO THE DISK

SAVE THE PARAMETER TO THE DISK

SENDING THE PARAMETERS TO THE WCDMA BTS

RESETTING THE WCDMA BTS

NOW THE NOKIA FLEXI WCDMA BTS IS CONFIGURED

ALL THE DATA ARE SENT TO THE BTS.

CHECK FOR THE ALRMS IF ANY.

LAUNCH FLEXI HUB MANAGER TO CONFIGURE FTFA