PROLEC RATED CAPACITY INDICATOR. - ab2000.co.uk · 25 Benson Rd, Nuffield Industrial Estate Poole,...

Post on 12-Jul-2018

214 views 0 download

transcript

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.37

7.50 5.04 4.05

7.00 4.12 3.40

6.50 4.14 3.44 2.89

6.00 3.45 2.91 2.49

5.50 3.45 2.92 2.50

5.00 4.04a 3.43 2.91 2.50 2.17

4.50 3.91a 3.42 2.90 2.50 2.17

4.00 3.93a 3.39 2.88 2.48 2.16 1.90

3.50 3.60a 4.02 3.36 2.86 2.47 2.15 1.89

3.00 4.12a 3.97 3.32 2.83 2.45 2.14 1.89

2.50 4.80 3.92 3.29 2.81 2.43 2.13 1.88

2.00 4.73 3.87 3.25 2.78 2.41 2.12 1.87

1.50 4.66 3.82 3.21 2.75 2.39 2.10 1.87

1.00 4.60 3.78 3.18 2.73 2.38 2.09 1.86

0.50 5.75 4.56 3.75 3.16 2.71 2.36 2.08 1.86

(m) 0.00 7.63 5.71 4.53 3.72 3.14 2.70 2.36 2.08

-0.50 6.65a 7.61 5.69 4.51 3.71 3.13 2.69 2.35 2.09

-1.00 8.29a 7.61 5.69 4.50 3.70 3.13 2.69 2.36

-1.50 7.63 5.69 4.51 3.71 3.14 2.70

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 1 of 23 Pressure).

H

e

i

g

h

t

03.12.2009 DPM

8485

CRR624

Colmar T7000Machine Type

Equipment

3AU

RCI Serial No

CANTED RAIL FRONT FLOATING

UNLOCKED

3m57 + 3m10 Tele Dipper

EXTENDED

± 10°

Radius (m)

Op Mode

Sector

Osc. Axle

Dipper Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.47

5.00 4.04a 4.43a 4.74a 4.47 3.85

4.50 3.91a 4.34a 4.69a 4.46 3.86

4.00 3.93a 4.38a 4.73a 4.44 3.85 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 4.42 3.83 3.36

3.00 4.12a 4.62a 4.98a 5.13 4.39 3.81 3.35

2.50 5.24a 5.49a 5.66a 5.09 4.36 3.79 3.34

2.00 7.52a 6.97a 5.99 5.05 4.33 3.77 3.33

1.50 9.12 7.22 5.94 5.01 4.31 3.75 3.31

1.00 9.02 7.16 5.89 4.98 4.28 3.74 3.31

0.50 9.99 8.95 7.11 5.85 4.95 4.26 3.73 3.31

(m) 0.00 9.99 9.99 8.90 7.07 5.83 4.93 4.25 3.72

-0.50 6.65a 9.99 9.99 8.87 7.04 5.81 4.92 4.25 3.73

-1.00 8.29a 9.99 9.99 8.86 7.04 5.81 4.92 4.26

-1.50 9.99 9.99 8.87 7.05 5.82 4.94

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 2 of 23 Pressure).

H

e

i

g

h

t

03.12.2009 DPM

CANTED RAIL FRONT FLOATING END

LOCKED

Radius (m)

Op Mode

Sector ± 10°

Machine Type

Equipment

RCI Serial No

Dipper

3AL

Colmar T7000

Extended Counterweight

3m57 + 3m10 Tele Dipper

Osc. Axle

8485

CRR624

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.79

7.50 5.53 4.56

7.00 4.62 3.89

6.50 4.64 3.92 3.36

6.00 3.93 3.38 2.93

5.50 3.93 3.39 2.95

5.00 4.04a 3.92 3.38 2.95 2.59

4.50 3.91a 3.91 3.37 2.94 2.59

4.00 3.93a 3.88 3.35 2.93 2.59 2.30

3.50 3.60a 4.14a 3.85 3.33 2.92 2.58 2.30

3.00 4.12a 4.49 3.82 3.31 2.90 2.57 2.29

2.50 5.24a 4.44 3.79 3.28 2.88 2.55 2.28

2.00 5.25 4.39 3.75 3.26 2.86 2.54 2.27

1.50 5.19 4.35 3.72 3.23 2.84 2.53 2.27

1.00 5.14 4.31 3.69 3.21 2.83 2.52 2.26

0.50 6.25 5.10 4.28 3.67 3.19 2.82 2.51 2.27

(m) 0.00 7.97 6.22 5.07 4.26 3.65 3.18 2.81 2.51

-0.50 6.65a 7.95 6.20 5.06 4.24 3.64 3.18 2.81 2.51

-1.00 8.29a 7.95 6.20 5.05 4.24 3.64 3.18 2.81

-1.50 7.97 6.21 5.06 4.25 3.65 3.19

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 3 of 23 Pressure).

RCI Serial No

Radius (m)

Op Mode

Sector

Osc. Axle

Dipper

CANTED RAIL FRONT FLOATING END

UNLOCKED

3m57 + 3m10 Tele Dipper

EXTENDED Counterweight

± 10°

H

e

i

g

h

t

03.12.2009 DPM

8485

CRR624

Colmar T7000Machine Type

Equipment

3AUC

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.68a

4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 5.09a 4.87 4.15a

3.00 4.12a 4.62a 4.98a 5.23a 5.35a 4.85 4.34

2.50 5.24a 5.49a 5.66a 5.74a 5.46 4.84 4.33

2.00 7.52a 6.97a 6.68a 6.19 5.43 4.82 4.32

1.50 9.99 8.39 7.12 6.16 5.41 4.80 4.31

1.00 9.99 8.33 7.08 6.13 5.38 4.79 4.30

0.50 9.99 9.99 8.28 7.04 6.10 5.37 4.78 3.97a

(m) 0.00 9.99 9.99 9.96 8.25 7.02 6.09 5.36 4.77

-0.50 6.65a 9.99 9.99 9.94 8.23 7.01 6.08 5.35 4.78

-1.00 8.29a 9.99 9.99 9.93 8.23 7.00 6.08 5.36

-1.50 9.99 9.99 9.94 8.24 7.01 6.09

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 4 of 23 Pressure).

Machine Type

Equipment

8485

CRR624

Colmar T7000

RCI Serial No

3m57 + 3m10 Tele Dipper

H

e

i

g

h

t

03.12.2009 DPM

LOCKED

Radius (m)

3ALC

± 10°

EXTENDED Counterweight

Op Mode

Sector

Osc. Axle

Dipper

CANTED RAIL FRONT FLOATING END

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 2.92

7.50 2.38

7.00 2.43 1.95

6.50 1.98 1.62

6.00 1.99 1.64 1.36

5.50 1.99 1.64 1.36 1.13

5.00 1.97 1.63 1.36 1.14

4.50 1.95 1.62 1.35 1.14 0.96

4.00 2.37 1.93 1.60 1.34 1.13 0.96

3.50 2.92 2.32 1.89 1.57 1.32 1.12 0.95

3.00 2.84 2.27 1.86 1.54 1.30 1.10 0.94

2.50 2.21 1.81 1.51 1.28 1.09 0.93 0.81

2.00 2.16 1.77 1.48 1.26 1.07 0.92 0.80

1.50 2.61 2.10 1.74 1.46 1.24 1.06 0.91

1.00 2.55 2.06 1.70 1.43 1.22 1.05 0.91

0.50 2.50 2.03 1.68 1.41 1.20 1.04 0.90

(m) 0.00 3.17 2.47 2.00 1.66 1.40 1.20 1.03 0.91

-0.50 4.27 3.15 2.46 1.99 1.65 1.39 1.19 1.03

-1.00 6.45 4.28 3.14 2.45 1.98 1.64 1.39 1.19

-1.50 4.29 3.15 2.46 1.99 1.65 1.40

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 5 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3B Op Mode CANTED RAIL FRONT FLOATING END

Sector ± 10° - 45°

UNLOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

U Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 5.33

7.50 4.18

7.00 4.26 3.36

6.50 3.40 2.75

6.00 3.42 2.77 2.28

5.50 3.41 2.78 2.29 1.90

5.00 3.39 2.76 2.29 1.91

4.50 3.36 2.74 2.28 1.91 1.61

4.00 3.71a 3.32 2.71 2.25 1.90 1.61

3.50 3.33a 3.92a 3.27 2.67 2.23 1.88 1.60

3.00 3.86a 4.01 3.21 2.63 2.20 1.86 1.58

2.50 3.92 3.14 2.59 2.16 1.83 1.57 1.35

2.00 3.83 3.08 2.54 2.13 1.81 1.55 1.35

1.50 4.80 3.74 3.02 2.50 2.10 1.79 1.54

1.00 4.70 3.67 2.97 2.46 2.07 1.77 1.53

0.50 4.63 3.62 2.93 2.43 2.05 1.76 1.52

(m) 0.00 6.19 4.58 3.58 2.90 2.41 2.04 1.75 1.53

-0.50 8.81a 6.16 4.55 3.55 2.88 2.40 2.03 1.75

-1.00 7.02a 9.24 6.15 4.54 3.55 2.88 2.40 2.04

-1.50 9.27 6.17 4.55 3.55 2.89 2.41

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 6 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3B Op Mode CANTED RAIL FRONT FLOATING END

Sector ± 10° - 45°

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

L Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 3.44

7.50 2.87

7.00 2.91 2.42

6.50 2.44 2.05

6.00 2.45 2.07 1.76

5.50 2.45 2.07 1.77 1.51

5.00 2.43 2.06 1.77 1.52

4.50 2.42 2.05 1.76 1.52 1.31

4.00 2.86 2.39 2.03 1.74 1.51 1.31

3.50 3.33a 2.82 2.36 2.01 1.73 1.50 1.31

3.00 3.37 2.77 2.32 1.98 1.71 1.49 1.30

2.50 2.72 2.29 1.95 1.69 1.47 1.29 1.14

2.00 2.67 2.25 1.93 1.67 1.46 1.28 1.14

1.50 3.16 2.62 2.21 1.90 1.65 1.44 1.27

1.00 3.11 2.58 2.18 1.88 1.63 1.43 1.27

0.50 3.07 2.55 2.16 1.86 1.62 1.42 1.26

(m) 0.00 3.76 3.04 2.53 2.14 1.85 1.61 1.42 1.27

-0.50 4.85 3.75 3.02 2.51 2.13 1.84 1.60 1.42

-1.00 6.77 4.86 3.74 3.02 2.51 2.13 1.84 1.61

-1.50 4.87 3.75 3.02 2.51 2.13 1.84

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 7 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3B Op Mode CANTED RAIL FRONT FLOATING END

Sector ± 10° - 45°

UNLOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

UC Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.32a

7.50 5.73

7.00 5.49b 4.66

6.50 4.70 3.87

6.00 4.72 3.89 3.26

5.50 4.48a 3.90 3.28 2.78

5.00 4.26a 3.88 3.27 2.79

4.50 4.17a 3.86 3.26 2.79 2.40

4.00 3.71a 4.20a 3.83 3.24 2.77 2.40

3.50 3.33a 3.92a 4.40a 3.79 3.21 2.75 2.39

3.00 3.86a 4.42a 4.51 3.75 3.18 2.73 2.37

2.50 5.39a 4.45 3.71 3.15 2.71 2.36 2.07

2.00 5.38 4.38 3.66 3.11 2.69 2.34 2.07

1.50 6.72 5.29 4.32 3.62 3.08 2.67 2.33

1.00 6.62 5.22 4.27 3.58 3.06 2.65 2.32

0.50 6.55 5.17 4.23 3.55 3.04 2.63 2.32

(m) 0.00 8.71 6.50 5.13 4.20 3.53 3.02 2.63 2.32

-0.50 8.81a 8.68 6.47 5.11 4.18 3.52 3.02 2.63

-1.00 7.02a 9.99 8.67 6.46 5.10 4.18 3.52 3.02

-1.50 9.99 8.69 6.47 5.11 4.19 3.53

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 8 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3B Op Mode CANTED RAIL FRONT FLOATING END

Sector ± 10° - 45°

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

LC Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 2.77

7.50 2.23

7.00 2.28 1.82

6.50 1.84 1.49

6.00 1.85 1.51 1.23

5.50 1.85 1.51 1.24 1.02

5.00 1.84 1.50 1.24 1.03

4.50 1.82 1.49 1.23 1.03 0.85

4.00 2.22 1.79 1.47 1.22 1.02 0.85

3.50 2.76 2.17 1.75 1.44 1.20 1.01 0.85

3.00 2.68 2.12 1.71 1.41 1.18 0.99 0.84

2.50 2.06 1.67 1.38 1.16 0.98 0.83 0.71

2.00 2.00 1.63 1.35 1.13 0.96 0.82 0.70

1.50 2.44 1.95 1.59 1.32 1.11 0.94 0.81

1.00 2.38 1.90 1.56 1.30 1.09 0.93 0.80

0.50 2.33 1.87 1.53 1.28 1.08 0.92 0.80

(m) 0.00 2.98 2.30 1.84 1.51 1.26 1.07 0.92 0.80

-0.50 4.10 2.96 2.28 1.83 1.50 1.26 1.07 0.92

-1.00 6.41 4.11 2.96 2.28 1.82 1.50 1.25 1.07

-1.50 4.13 2.97 2.28 1.83 1.50 1.26

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 9 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3C Op Mode CANTED RAIL

Sector ± 45° - 135° overside

UNLOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

U Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 4.91

7.50 3.99

7.00 4.05 3.29

6.50 3.32 2.75

6.00 3.34 2.77 2.32

5.50 3.33 2.77 2.33 1.97

5.00 3.31 2.76 2.33 1.98

4.50 3.29 2.74 2.31 1.97 1.69

4.00 3.71a 3.25 2.71 2.29 1.96 1.68

3.50 3.33a 3.91 3.20 2.68 2.27 1.94 1.68

3.00 3.86a 3.83 3.15 2.64 2.24 1.92 1.66

2.50 3.75 3.09 2.60 2.21 1.90 1.65 1.44

2.00 3.68 3.04 2.56 2.18 1.88 1.64 1.44

1.50 4.47 3.60 2.99 2.52 2.15 1.86 1.62

1.00 4.38 3.54 2.94 2.48 2.13 1.85 1.61

0.50 4.32 3.50 2.90 2.46 2.11 1.83 1.61

(m) 0.00 5.49 4.27 3.46 2.88 2.44 2.10 1.83 1.61

-0.50 7.49 5.46 4.25 3.44 2.86 2.43 2.09 1.83

-1.00 7.02a 7.49 5.46 4.24 3.43 2.86 2.43 2.10

-1.50 7.52 5.47 4.25 3.44 2.86 2.44

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 10 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3C Op Mode CANTED RAIL

Sector ± 45° - 135° overside

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

L Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 5.99

7.50 4.89

7.00 4.95 4.06

6.50 4.09 3.42

6.00 4.11 3.44 2.92

5.50 4.10 3.44 2.93 2.51

5.00 4.09 3.43 2.93 2.52

4.50 4.06 3.41 2.91 2.51 2.18

4.00 3.71a 4.02 3.39 2.89 2.50 2.18

3.50 3.33a 3.92a 3.97 3.35 2.87 2.48 2.17

3.00 3.86a 4.42a 3.92 3.31 2.84 2.46 2.16

2.50 4.65 3.86 3.27 2.81 2.44 2.14 1.89

2.00 4.58 3.81 3.23 2.78 2.42 2.13 1.89

1.50 5.55 4.50 3.76 3.19 2.75 2.40 2.12

1.00 5.46 4.44 3.71 3.16 2.73 2.39 2.11

0.50 5.40 4.40 3.67 3.13 2.71 2.37 2.10

(m) 0.00 6.84 5.35 4.36 3.65 3.11 2.70 2.37 2.10

-0.50 8.81a 6.81 5.33 4.34 3.63 3.10 2.69 2.37

-1.00 7.02a 9.29 6.81 5.32 4.33 3.63 3.10 2.70

-1.50 9.32 6.82 5.33 4.34 3.64 3.11

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 11 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3C Op Mode CANTED RAIL

Sector ± 45° - 135° overside

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

LC Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 3.70

7.50 3.16 2.67

7.00 2.72 2.34

6.50 2.73 2.36 2.05

6.00 2.37 2.07 1.80

5.50 2.37 2.07 1.82

5.00 2.73 2.36 2.06 1.82 1.60

4.50 2.71 2.35 2.05 1.81 1.61

4.00 2.68 2.33 2.04 1.80 1.60 1.42

3.50 3.09 2.65 2.31 2.02 1.79 1.59 1.42

3.00 3.05 2.62 2.28 2.00 1.78 1.58 1.42

2.50 3.00 2.58 2.25 1.98 1.76 1.57 1.41

2.00 2.95 2.55 2.22 1.96 1.74 1.56 1.40

1.50 2.90 2.51 2.20 1.94 1.73 1.55 1.40

1.00 2.86 2.48 2.18 1.93 1.72 1.54 1.40

0.50 3.32 2.83 2.46 2.16 1.91 1.71 1.54 1.40

(m) 0.00 3.94 3.29 2.81 2.44 2.14 1.90 1.70 1.53

-0.50 4.84 3.92 3.28 2.80 2.43 2.14 1.90 1.70 1.54

-1.00 4.84 3.92 3.28 2.80 2.43 2.14 1.90 1.70

-1.50 3.93 3.28 2.80 2.43 2.14 1.91

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 12 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3D Op Mode CANTED RAIL FIXED REAR END

Sector ± 135° - 150° over rear

UNLOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

U Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 5.97

7.50 5.12 4.41

7.00 4.45 3.88

6.50 4.47 3.91 3.44

6.00 3.92 3.46 3.07

5.50 3.92 3.47 3.09

5.00 4.04a 3.91 3.46 3.09 2.77

4.50 3.91a 3.89 3.45 3.08 2.77

4.00 3.93a 3.87 3.43 3.07 2.76 2.49

3.50 3.60a 4.14a 3.85 3.41 3.06 2.75 2.49

3.00 4.12a 4.34 3.82 3.39 3.04 2.74 2.49

2.50 4.95 4.30 3.79 3.37 3.02 2.73 2.48

2.00 4.89 4.26 3.76 3.35 3.01 2.72 2.47

1.50 4.84 4.22 3.73 3.32 2.99 2.71 2.47

1.00 4.80 4.19 3.70 3.31 2.98 2.70 2.46

0.50 5.54 4.76 4.16 3.68 3.29 2.96 2.69 2.46

(m) 0.00 6.55 5.51 4.74 4.14 3.67 3.28 2.96 2.69

-0.50 6.65a 6.53 5.50 4.73 4.13 3.66 3.27 2.96 2.69

-1.00 8.01 6.53 5.50 4.72 4.13 3.66 3.27 2.96

-1.50 6.54 5.50 4.73 4.13 3.66 3.28

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 13 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3D Op Mode CANTED RAIL FIXED REAR END

Sector ± 135° - 150° over rear

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

L Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 4.09

7.50 3.50 2.98

7.00 3.02 2.61

6.50 3.04 2.63 2.30

6.00 2.64 2.31 2.03

5.50 2.64 2.32 2.04

5.00 3.03 2.63 2.31 2.04 1.81

4.50 3.01 2.62 2.30 2.04 1.81

4.00 2.99 2.60 2.29 2.03 1.81 1.62

3.50 3.43 2.96 2.58 2.27 2.02 1.80 1.62

3.00 3.39 2.92 2.55 2.25 2.00 1.79 1.61

2.50 3.34 2.89 2.53 2.23 1.99 1.78 1.60

2.00 3.29 2.85 2.50 2.21 1.97 1.77 1.60

1.50 3.24 2.82 2.47 2.19 1.96 1.76 1.59

1.00 3.21 2.79 2.45 2.17 1.94 1.75 1.59

0.50 3.71 3.18 2.76 2.43 2.16 1.93 1.75 1.59

(m) 0.00 4.40 3.69 3.16 2.75 2.42 2.15 1.93 1.74

-0.50 5.40 4.39 3.67 3.15 2.74 2.41 2.15 1.93 1.75

-1.00 5.40 4.39 3.67 3.14 2.73 2.41 2.15 1.93

-1.50 4.39 3.68 3.15 2.74 2.41 2.15

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 14 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3D Op Mode CANTED RAIL FIXED REAR END

Sector ± 135° - 150° over rear

UNLOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

UC Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.73

7.50 5.79 4.99

7.00 5.04 4.41

6.50 5.05a 4.44 3.92

6.00 4.45 3.94 3.51

5.50 4.45 3.94 3.52

5.00 4.04a 4.43a 3.94 3.52 3.17

4.50 3.91a 4.34a 3.93 3.52 3.17

4.00 3.93a 4.38a 3.91 3.51 3.17 2.87

3.50 3.60a 4.14a 4.38 3.89 3.49 3.16 2.87

3.00 4.12a 4.62a 4.35 3.87 3.48 3.15 2.86

2.50 5.24a 4.89 4.32 3.85 3.46 3.13 2.85

2.00 5.55 4.85 4.29 3.83 3.44 3.12 2.85

1.50 5.50 4.81 4.26 3.80 3.43 3.11 2.84

1.00 5.46 4.78 4.23 3.78 3.41 3.10 2.84

0.50 6.30 5.43 4.75 4.21 3.77 3.40 3.09 2.84

(m) 0.00 7.44 6.27 5.41 4.73 4.20 3.76 3.40 3.09

-0.50 6.65a 7.43 6.26 5.39 4.72 4.19 3.75 3.39 3.10

-1.00 8.29a 7.43 6.26 5.39 4.72 4.19 3.75 3.40

-1.50 7.44 6.26 5.39 4.72 4.19 3.76

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 15 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3D Op Mode CANTED RAIL FIXED REAR END

Sector ± 135° - 150° over rear

LOCKED

Dipper EXTENDED Counterweight

Radius (m)

H

e

i

g

h

t

LC Osc. Axle

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 5.15

7.50 4.40 3.76

7.00 3.81 3.30

6.50 3.83 3.33 2.92

6.00 3.34 2.94 2.60

5.50 3.34 2.94 2.61

5.00 3.82 3.33 2.94 2.61 2.33

4.50 3.80 3.32 2.93 2.60 2.33

4.00 3.77 3.30 2.91 2.59 2.33 2.09

3.50 3.60a 3.74 3.27 2.89 2.58 2.32 2.09

3.00 4.12a 3.71 3.25 2.87 2.57 2.31 2.09

2.50 4.24 3.67 3.22 2.85 2.55 2.30 2.08

2.00 4.19 3.63 3.19 2.83 2.54 2.29 2.07

1.50 4.14 3.60 3.16 2.81 2.52 2.28 2.07

1.00 4.10 3.57 3.14 2.80 2.51 2.27 2.07

0.50 4.76 4.07 3.54 3.12 2.78 2.50 2.26 2.07

(m) 0.00 5.65 4.73 4.05 3.53 3.11 2.77 2.49 2.26

-0.50 6.65a 5.64 4.72 4.04 3.52 3.10 2.77 2.49 2.26

-1.00 6.97 5.64 4.71 4.03 3.51 3.10 2.77 2.50

-1.50 5.65 4.72 4.04 3.52 3.11 2.78

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 16 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3E Op Mode CANTED RAIL FIXED REAR END

Sector ± 150° - 160° over rear

Radius (m)

H

e

i

g

h

t

U Osc. Axle UNLOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.77

5.00 4.04a 4.43a 4.74a 4.77 4.26a

4.50 3.91a 4.34a 4.69a 4.76 4.30

4.00 3.93a 4.38a 4.73a 4.75 4.29 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 4.73 4.28 3.89

3.00 4.12a 4.62a 4.98a 5.23a 4.71 4.27 3.88

2.50 5.24a 5.49a 5.66a 5.22 4.69 4.25 3.88

2.00 7.52a 6.59 5.82 5.19 4.67 4.24 3.87

1.50 7.49 6.54 5.78 5.16 4.65 4.22 3.86

1.00 7.44 6.50 5.75 5.14 4.64 4.21 3.85

0.50 8.61 7.40 6.47 5.73 5.12 4.62 4.20 3.86

(m) 0.00 9.99 8.58 7.37 6.44 5.71 5.11 4.61 4.20

-0.50 6.65a 9.99 8.56 7.36 6.43 5.70 5.10 4.61 4.21

-1.00 8.29a 9.99 8.56 7.35 6.43 5.69 5.10 4.62

-1.50 9.99 8.57 7.36 6.43 5.70 5.11

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 17 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3E Op Mode CANTED RAIL FIXED REAR END

Sector ± 150° - 160° over rear

Radius (m)

H

e

i

g

h

t

L Osc. Axle LOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 5.70

7.50 4.88 4.19

7.00 4.23 3.68

6.50 4.25 3.71 3.26

6.00 3.72 3.28 2.91

5.50 3.72 3.28 2.92

5.00 4.04a 3.71 3.28 2.92 2.62

4.50 3.91a 3.70 3.27 2.92 2.62

4.00 3.93a 3.68 3.26 2.91 2.62 2.36

3.50 3.60a 4.14a 3.65 3.24 2.90 2.61 2.36

3.00 4.12a 4.13 3.63 3.22 2.88 2.60 2.36

2.50 4.72 4.09 3.60 3.20 2.87 2.59 2.35

2.00 4.67 4.05 3.57 3.18 2.85 2.58 2.34

1.50 4.62 4.02 3.54 3.16 2.84 2.57 2.34

1.00 4.58 3.99 3.52 3.14 2.82 2.56 2.33

0.50 5.31 4.55 3.97 3.50 3.13 2.81 2.55 2.33

(m) 0.00 6.30 5.28 4.53 3.95 3.49 3.12 2.81 2.55

-0.50 6.65a 6.29 5.27 4.52 3.94 3.48 3.11 2.80 2.55

-1.00 7.77 6.29 5.27 4.51 3.94 3.48 3.11 2.81

-1.50 6.30 5.27 4.52 3.94 3.48 3.12

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 18 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3E Op Mode CANTED RAIL FIXED REAR END

Sector ± 150° - 160° over rear

Radius (m)

H

e

i

g

h

t

UC Osc. Axle UNLOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.49

4.00 3.93a 4.38a 4.73a 4.94a 4.49 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 4.95 4.47 4.07

3.00 4.12a 4.62a 4.98a 5.23a 4.93 4.46 4.06

2.50 5.24a 5.49a 5.66a 5.45 4.90 4.45 4.06

2.00 7.52a 6.87 6.07 5.42 4.88 4.43 4.05

1.50 7.82 6.82 6.04 5.39 4.86 4.42 4.04

1.00 7.76 6.78 6.00 5.37 4.85 4.41 4.03

0.50 8.98 7.72 6.75 5.98 5.35 4.83 4.40 3.97a

(m) 0.00 9.99 8.95 7.70 6.73 5.96 5.34 4.83 4.40

-0.50 6.65a 9.99 8.93 7.68 6.71 5.95 5.33 4.82 4.40

-1.00 8.29a 9.99 8.93 7.67 6.71 5.95 5.33 4.83

-1.50 9.99 8.94 7.68 6.72 5.96 5.34

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 19 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3E Op Mode CANTED RAIL FIXED REAR END

Sector ± 150° - 160° over rear

Radius (m)

H

e

i

g

h

t

LC Osc. Axle LOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.43

4.00 3.93a 4.38a 4.73a 4.87 4.42 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 4.86 4.42 4.04

3.00 4.12a 4.62a 4.98a 5.23a 4.85 4.41 4.03

2.50 5.24a 5.49a 5.66a 5.35 4.83 4.39 4.02

2.00 7.52a 6.70 5.94 5.33 4.81 4.38 4.02

1.50 7.62 6.67 5.92 5.31 4.80 4.37 4.01

1.00 7.58 6.64 5.89 5.29 4.79 4.36 4.01

0.50 8.76 7.55 6.62 5.88 5.27 4.78 4.36 3.97a

(m) 0.00 9.99 8.73 7.53 6.60 5.86 5.26 4.77 4.36

-0.50 6.65a 9.99 8.72 7.51 6.59 5.85 5.26 4.77 4.36

-1.00 8.29a 9.99 8.72 7.51 6.58 5.85 5.26 4.77

-1.50 9.99 8.72 7.51 6.59 5.86 5.27

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 20 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3F Op Mode CANTED RAIL FIXED REAR END

Sector ± 160° - 180° over rear

Radius (m)

H

e

i

g

h

t

U Osc. Axle UNLOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

IN

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.68a

4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 5.09a 5.03 4.15a

3.00 4.12a 4.62a 4.98a 5.23a 5.35a 5.01 4.50a

2.50 5.24a 5.49a 5.66a 5.74a 5.58 4.99 4.51

2.00 7.52a 6.97a 6.68a 6.27 5.56 4.98 4.50

1.50 9.72 8.23 7.11 6.23 5.53 4.96 4.49

1.00 9.65 8.18 7.07 6.21 5.51 4.95 4.48

0.50 9.99 9.60 8.14 7.04 6.18 5.50 4.94 3.97a

(m) 0.00 9.99 9.99 9.57 8.11 7.02 6.17 5.49 4.94

-0.50 6.65a 9.99 9.99 9.55 8.10 7.01 6.16 5.49 4.94

-1.00 8.29a 9.99 9.99 9.54 8.09 7.00 6.16 5.49

-1.50 9.99 9.99 9.55 8.10 7.01 6.17

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 21 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3F Op Mode CANTED RAIL FIXED REAR END

Sector ± 160° - 180° over rear

Radius (m)

H

e

i

g

h

t

L Osc. Axle LOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.43

4.00 3.93a 4.38a 4.73a 4.87 4.42 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 4.86 4.42 4.04

3.00 4.12a 4.62a 4.98a 5.23a 4.85 4.41 4.03

2.50 5.24a 5.49a 5.66a 5.35 4.83 4.39 4.02

2.00 7.52a 6.70 5.94 5.33 4.81 4.38 4.02

1.50 7.62 6.67 5.92 5.31 4.80 4.37 4.01

1.00 7.58 6.64 5.89 5.29 4.79 4.36 4.01

0.50 8.76 7.55 6.62 5.88 5.27 4.78 4.36 3.97a

(m) 0.00 9.99 8.73 7.53 6.60 5.86 5.26 4.77 4.36

-0.50 6.65a 9.99 8.72 7.51 6.59 5.85 5.26 4.77 4.36

-1.00 8.29a 9.99 8.72 7.51 6.58 5.85 5.26 4.77

-1.50 9.99 8.72 7.51 6.59 5.86 5.27

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 22 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3F Op Mode CANTED RAIL FIXED REAR END

Sector ± 160° - 180° over rear

Radius (m)

H

e

i

g

h

t

UC Osc. Axle UNLOCKED

Dipper EXTENDED Counterweight

25 Benson Rd, Nuffield Industrial Estate

Poole, Dorset. BH17 0GB

Tel: 01202 681190

Fax: 01202 677909

E-mail: info@prolec.co.uk

PROLEC RATED CAPACITY INDICATOR.

PLEASE READ AND UNDERSTAND THE OPERATING

INSTRUCTIONS BEFORE USING THE EQUIPMENT

M/C Serial No.

M/C Plant No.

Compiled

OUT

50 - 150mm

2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

8.00 6.94a

7.50 6.06b 5.53a

7.00 5.52a 5.22a

6.50 5.05a 5.20a 4.83a

6.00 4.89a 5.00a 4.18a

5.50 4.62a 4.86a 4.79a

5.00 4.04a 4.43a 4.74a 4.86a 4.26a

4.50 3.91a 4.34a 4.69a 4.87a 4.68a

4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a

3.50 3.60a 4.14a 4.58a 4.91a 5.09a 5.03 4.15a

3.00 4.12a 4.62a 4.98a 5.23a 5.35a 5.01 4.50a

2.50 5.24a 5.49a 5.66a 5.74a 5.58 4.99 4.51

2.00 7.52a 6.97a 6.68a 6.27 5.56 4.98 4.50

1.50 9.72 8.23 7.11 6.23 5.53 4.96 4.49

1.00 9.65 8.18 7.07 6.21 5.51 4.95 4.48

0.50 9.99 9.60 8.14 7.04 6.18 5.50 4.94 3.97a

(m) 0.00 9.99 9.99 9.57 8.11 7.02 6.17 5.49 4.94

-0.50 6.65a 9.99 9.99 9.55 8.10 7.01 6.16 5.49 4.94

-1.00 8.29a 9.99 9.99 9.54 8.09 7.00 6.16 5.49

-1.50 9.99 9.99 9.55 8.10 7.01 6.17

-2.00

-2.50

-3.00

-3.50

-4.00

NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted

and assume the load is suspended vertically below the bucket pin.

The weight of bucket, slings/auxillary devices must be deducted from the above loads.

Radius/height is given in METRES measured from slew centre/ground level respectively.

Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic

PAGE 23 of 23 Pressure).

Machine Type Colmar T7000 8485

RCI Serial No CRR624

Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM

3F Op Mode CANTED RAIL FIXED REAR END

Sector ± 160° - 180° over rear

Radius (m)

H

e

i

g

h

t

LC Osc. Axle LOCKED

Dipper EXTENDED Counterweight