Post on 06-Feb-2018
transcript
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
This list identifies works approved by Lloyd’s Register Group Limited (LR) for steelmakingand the manufacture of rolled steel plate, strip, sections and bars in accordance with therequirements of LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 3.
The information listed for each works is a summary of the product, generic grade andmaximum thickness, or in the case of round bars, diameter approved.
It is important to note that this list does not provide full details of the grades approved byLR as required by the Rules. The combinations of deoxidation practice (e.g. killed,semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included.These parameters may vary within each grade by manufacturer and could influence thefabrication procedures that can be applied.
The list also includes firms approved for the manufacture of fabricated steel sections.
Where required this information should be obtained from the current certificate of approvalissued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Schemein accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other worksowned by the same company. The local LR surveying office is also listed.
Abbreviations:
B.O.S. Basic Oxygen SteelmakingCon Cast Continuous CastingE.A.F. Electric Arc FurnaceO.H. Open Hearth
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,employees or agents are, individually and collectively, referred to in this clause as 'Lloyd'sRegister'. Lloyd's Register assumes no responsibility and shall not be liable to any personfor any loss, damage or expense caused by reliance on the information or advice in thisdocument or howsoever provided, unless that person has signed a contract with therelevant Lloyd's Register entity for the provision of this information or advice and in thatcase any responsibility or liability is exclusively on the terms and conditions set out in thatcontract.
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
As at 10 April 2018
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Australia
As belowB.O.S. / Con CastSteelmakingBLUESCOPE STEEL (AIS) PTY. LTD. SydneyA, B, D, E 51Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
51Higher Strength
A, B, D, E 13Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
6Higher Strength
P.O. Box 1854Wollongong
Port Kembla Steelworks
Tel: +61 2 42754666 Fax: +61 2 42753045 Email: nigel.attwell@bluescopesteel.comPlates with specified through thickness properties notation Z35 may be added.Normalizing heat treatments carried out by sub-contractor, Bisalloy.
Certificate # MD00/1929/0009/1 Expiry date: 28/07/2018
NSW 2500
Austria
As belowE.A.F./V.O.D./IngotSteelmakingBREITENFELD EDELSTAHL AG Viennacarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
120Ingots (tonnes)Semi-Finished
8662 St. Barbara im MürztalBreitenfelderstrasse 22
Tel: +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email mailto:marina.paller@breitenfeld.atWeb: http://www.breitenfeld.atCertificate # MD00/3255/0005/1 Expiry Date: 06/06/2018Including VD/VOD
A, B, D, E 20Normal StrengthSectionsBÖHLER PROFIL GmbH ViennaAH32, AH36, DH32, DH36, EH32, EH36 20Higher StrengthA, B, D, E 20Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 20Higher Strengthcarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
20Structural
Waidhofnerstraße 83333 BöhlerwerkTel: +43 7448 7007 24504 Fax: +43 7448 7007 24602 email: herwig.kohlreiter@bohler-profil.com web: www.bohler-profil.com
Certificate #: MD00/0202/0007/1 Expiry date: 27/01/2018
High alloy bars and sections may be accepted for approved applications.
As below 38VAR/INGOTSteelmakingSONDERSTAHLWERK BREITENFELD GmbH Viennacarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
38Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy, austeniticstainless, duplex
38IngotsESR
8662 St. Barbara im MürtztalBreitenfelderstasse 22
Tel +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email marina.paller@breitenfeld.at Web http://www.breitenfeld.at
Certificate # MD00/3256/0005/1 Expiry date: 06/06/2018Including remelting of Ni materials
A 120Normal StrengthBarsSTAHL JUDENBURG GmbH Viennacarbon, carbon-manganese 120Structuralcarbon, carbon-manganese, carbon-manganese 120Machinery
Gußstahlwerkstrasse 21A-8750 JudenburgTel: +43 3572 701-358 Fax: +43 3572 701-248
E-mail: christian.sunnitsch@stj.at
Website: www.stahl-judenburg.com
Certificate No: MD00/1643/0008/1 Expiry date: 27/01/2021
As at 10 April 2018 2Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F./Ingot/Con CastSteelmakingVOESTALPINE BÖHLER EDELSTAHL GmbH & CoKG
Vienna
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
220StructuralBars
Postfach 96A-8605 Kapfenberg
Mariazellerstraße 25
Tel: +43 3862 20 36698 Fax: +43 3862 20 37559email: silke.schneller@voestalpine.com web: ww.bohler-edelstahl.comCertificate #: MD00/0200/0009/1 Expiry date: 20/01/2021
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingVOESTALPINE STAHL DONAWITZ GmbH Viennacarbon, carbon-manganese, alloy 283Blooms/BilletsSemi-Finished
A 8700 LeobenKerpelystraße 199
Tel: +43 50304 25-4659 Fax: +43 50304 65-2464 Email: mailto:karin.rockenschaub@voestalpine.com Web:http://www.voestalpine.com/stahldonawitzCertificate #: MD00/2976/0005/1 Expiry date: 20/04/2018
As belowB.O.S. / Con CastSteelmakingvoestalpine Grobblech GmbH ViennaA, B, D, E 140Normal StrengthPlatesAH42, DH42, EH42 55Higher StrengthAH40, DH40, EH40, FH40 100AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
140
360AR 40Boiler & Pressure Vessel410AR 50360FG, 410FG, 460FG, 490FG, 510FG 1401.5Ni, 3.5Ni, 5Ni, 9Ni 50Ferritic Low TemperatureLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36
140
D/304L 50Clad
P.O Box 3Voest.- Alpine - Str. 3
Tel: +43 50304 15 9091 Fax: +43 50304 55 9091Email: ronald.lachmair@voestalpine.com Web: www.voestalpine.com
Certifcate No. MD00/1614/0010/1 Expiry date: 28/07/2020
Approval includes the supply of z25 and z35 grades.
Approval includes pressed heads.
A-4020 Linz
Belarus, Republic of
As belowE.A.F./V.O.D./Con CastSteelmakingOJSC "Byelorussian Steel Works-ManagementCompany of
St. Petersburg
Carbon, Carbon-Manganese 140Rolled BilletsSemi-Finished
carbon, carbon-manganese, Normal Strength 300Billets
37, Promyshlennaya Str.BY- 247210 Zhlobin,
"Byelorussian Metallurgical Company" holding"(OJSC "BSW -management company of "BMC" holding")
Tel No: +375 2334 56180 Fax no: +375 2334 56317 Mob +375 291105030Email : mailo: metizdir@bmz.gomel.byWeb: www.bmz.gomel.byCertificate No: MD00/4297/0002/1 Expiry date 04/03/2020
Gomel Region,
As at 10 April 2018 3Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Belgium
As belowE.A.F./A.O.D./Con CastSteelmakingAPERAM STAINLESS BELGIUM - CHATELET site Antwerpaustenitic stainless 200SlabsSemi-Finished
14, Rue des Ateliers6200 ChateletTel: +32 (0) 7160 7214 E-mail: Koenraad.VanVlierden@aperam.com
Website: www.aperam.com
Certificate Number: MD00/4387/0003/1 Expiry: 16/09/2020
austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingAPERAM STAINLESS STEEL EUROPE- Genk site Antwerpaustenitic stainlessE.A.F./V.O.D./Con Castaustenitic stainless 200SlabsSemi-Finished304L, 304LN, 316L, 316LN, 321, 347 14Austenitic StainlessPlates
Swinnenwijerweg 5B-3600 GenkTel: +32 89 30 1959 E-mail: Koenraad.VanVierden@aperam.com
Website: www.aperam.com
Certificate No: MD00/3423/0005/1 Expiry date: 27/01/2020
As belowE.A.F. / Con CastSteelmakingINDUSTEEL BELGIUM SA AntwerpA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36, EH40 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69, FH42, FH46,FH50, FH55, FH62, FH69
100
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, 5Ni, 9Ni
50Ferritic Low Temperature
304L, 304LN, 316L, 316LN 50Austenitic StainlessUNS S31803(MOD)* 40Duplex Stainless
266, Rue de ChâteletB-6030 Charleroi
ARCELOR MITTAL GROUP
Tel: +32 47 8 80 35 19 Fax: +32 71 44 19 29
E-mail: karim.BAHRI@arcelormittal.com
Website: http://www.industeel.arcelormittal.com
Plates in grades LTAH32; LTAH36; LTDH32; LTDH36; LTEH32; LTEH36; 5%Ni; 9%Ni over 40mm thickness and up to the maximum thickness stated above areaccepted for approved applications only.* accepted for approved applications.Higher strength grades supplied in the quenched and tempered grades are accepted with specified through thickness properties designation Z35.
Certificate Number: MD00/0477/0011/1 Expiry: 07/07/2020
A, B, D, E 120Normal StrengthPlatesNLMK CLABECQ S.A. AntwerpAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
120Higher Strength
360AR, 410AR 25Boiler & Pressure Vessel360, 410 50360FG, 410FG, 460FG, 490FG, 510FG 120
Rue de Clabecq, 101B-1460 IttreTel: +32 3919227 Fax: +32 3919883 Mobile +33 4972 297369
Email:j.vermeulen@eu.nlmk.com
Web:http://www.eu.nlmk.com
MQS Approved - Approval No. MQS016
Certificate #: MD00/2204/0013/1 Expiry date: 23.06.2018
As at 10 April 2018 4Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Brazil
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELORMITTAL BRAZIL S/A (ARCELORMITTALTUBARÃO )
Rio de Janeiro
carbon, carbon-manganese 250SlabsSemi-Finished
D 16Normal StrengthHot Rolled Coil
A, B 19
AH36 16Higher Strength
AH27S, AH32 19
510FG 16Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG 19
D 16Normal StrengthPlates from coils
A, B 19
AH36 16Higher Strength
AH27S, AH32 19
460 FG, 490FG 16Boiler and Pressure Vessel
410 FG, 360 FG 19
526 - Polo Industrial Tubarão,Distrito de Carapina Serra E.S - CEP 29160-904
Avenida Brigadeiro Eduardo Gomes,
Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
Tel: +55 27 3348 3215 Fax: +55 27 3348 2211
E-mail: marcelo.rodrigues@arcelormittal.com.br
Website: www.arcelormittal.com/br/tubarao
Material Quality Scheme approved, MQS 054
Certificate No: MD00/0342/0013/1 Expiry date: 28/06/2020
As belowB.O.S. / Con CastSteelmakingCSP - COMPANHIA SIDERURGICA DO PECÉM Rio de JaneiroNormal strength, Higher Strength 300SlabsSemi-Finished
Rodovia, Ce 155 s/n - km 11,5 CEP 62674-000,
Tel: +55 85 31048001email: thiago.bittencourt@cspecem.com web: www.cspecem.com
Certificate No: MD00/4676/0001/1 Expiry Date: 18/04/2020
São Gonçalo do Amarante (CE),
As belowB.O.S./Ingot/Con CastSteelmakingGERDAU AÇOMINAS S.A. Rio de JaneiroCarbon, Carbon-Manganese, Alloy 180Rolled BilletsSemi-Finishedcarbon, carbon-manganese, alloy 250Slabscarbon, carbon-manganese, alloy 300Bloomscarbon, carbon-manganese, alloy 180BilletsCarbon, Carbon-Manganese, Alloy 280Rolled BloomsA, B 50Normal StrengthPlatesA 20Normal StrengthHot Rolled Coil
Rodovia MG-443 KM 7Fazenda do Cadete
Tel: +55 32 3749 5637 Mob: +55 31 9 8391 0098email: aline.barbosa@gerdau.com.br web www.gerdau.com.br
Certificate #: MD00/2071/0010/1 Expiry date: 24/02/2021
36420-000-Ouro Branco-MG
As belowB.O.S. / Con CastSteelmakingUSIMINAS Rio de JaneiroA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A 12Normal StrengthHot Rolled Coil
As at 10 April 2018 5Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Brazil360, 410 12Boiler & Pressure VesselHot Rolled CoilUSIMINAS Rio de Janeiro
Av. Pedro Linhares Gomes, 5431Distrito Usiminas, CEP 35160-900
Usinas Siderúrgicas de Minas Gerais S/AUsina Intendente Câmera
Tel +55 (0)31 38293264 Fax +55 (0)31 38293516
E-mail: marcos.sampaio@usiminas.com
Z25 and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditions
Materials Quality Scheme Approved - MQS 014
Certificate No: MD00/1603/0010/1 Expiry date: 22/06/2020
Ipatinga, Minas Gerais
As belowB.O.S. / Con CastSteelmakingUSINAS SIDERÚRGICAS DE MINAS GERAIS S.A. -USIMINAS
São Paulo
A, B, D, E 80Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
Rodovia Cônego Domênico Rangoni, Km 6Vila da Indústrias 11573-900
Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: takayochi.ueno@usiminas.com Web:http://www.usiminas.comSpecified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously castslab.Material Quality Scheme approved, MQS 044Certificate #: MD00/1193/0009/1 Expiry date: 28/09/2017
Cubatão - São Paulo
Bulgaria
carbon, carbon-manganeseE.A.F. / IngotSteelmakingRADOMIR METAL INDUSTRIES JSC Sofiacarbon, carbon-manganese 25Ingots (tonnes)Semi-Finished
2400 Radomir,Tel: 359 77780489 Fax: 359 77782134email: rmindustries@mbox.contact.bg web: radomir-metal-industries.com
Certificate No: MD00/4386/0001/1 Expiry Date: 17/09/2017
As belowE.A.F. / Con CastSteelmakingSTOMANA INDUSTRY AD SofiaAs below 200Blooms/BilletsSemi-FinishedA 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
1, Vladaysko Vastanie Str.2304 PernikTel: +359 766 81028 Fax: +359 766 81952email:vsofteva@stomana.bg web: www.stomana.bgCertificate #: MD00/1868/0010/1 Expiry date: 16/04/2019
As at 10 April 2018 6Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Canada
As belowB.O.S. / Con CastSteelmakingESSAR STEEL ALGOMA INC. Torontocarbon, carbon-manganese 205SlabsSemi-FinishedD, E 50Normal StrengthPlatesA, B 60AH32, AH36, DH32, DH36, EH32, EH36 65Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 65Boiler & Pressure Vessel
Sault Ste. MarieOntario
105 West Street
Tel +1 705 945 2347 Fax: +1 705 945 2632 e-mail: lori.pilot@algoma.com web: www.essarsteelalgoma.com
Certificate #: MD00/0092/0009/1 Expiry date: 04/05/2020
P6A 5P2
As BelowEAF/LMF/Con CastSteelmakingEVRAZ NORTH AMERICA Vancouver BCA, B, AH36, DH36 200SlabsSemi-Finished
Regina, SKS4P 3C7
EVRAZ Regina Steel100 Armour Road
Tel: +1 800 667 1616 and 306 924 7500 Email to: steelplate@evrazna.com Web: http://www.evrazna.com
Slabs as semi-finished products of nominal dimensions 8" x 84" x 480" are approved
MATERIALS QUALITY SCHEME APPROVED - MQS 055Certificate No. :MD00/4490/0001/1 Expiry Date: 16/6/2018:
As belowE.A.F. / Con CastSteelmakingGERDAU LONGSTEEL NORTH AMERICA TorontoA, B 15Normal StrengthSectionsAH27S, AH32, AH36 15Higher Strength
WhitbyOntario
Whitby Steel Mill Operations1 Gerdau Court
Tel: +1 905 668 8811 ext 4055 Fax: +1 905 668 3742 Email: mailto:leonardo.nunes@gerdau.com Web: http://www.gerdau.comCertificate #: MD00/0322/0009/1 Expiry date: 29/01/2020CSA grades 260W, 300W and 350W may be accepteed for approved applications equivalent to the appropriate Lloyds Register grade above
L1N 5T1
China, People's Republic of
As belowE.A.F./A.O.D./Con CastSteelmakingANGANG LIANZHONG STAINLESS STEELCORPORATION
Guangzhou
duplex stainless 200SlabsSemi-Finished
East Section,Economy & Technology Development Zone,
No. 1 Lianguang Road,
Tel: +86 (0)20 2220 8888 Fax: +86 (0_20 3210 7529email: lzz6j960@lisco.com.cn web: www.lisco.com.cn
Certificate No: MD00/4706/0001/1 Expiry Date: 04/09/2020
Guangzhou,
A, B, D, E 100Normal StrengthPlatesANGANG STEEL COMPANY LIMITED DalianAH42, AH46, AH50, AH55, DH42, DH46, DH50,DH55, EH42, EH46, EH50, EH55, FH42, FH46,FH50, FH55
80Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,DH40, EH27S, EH32, EH36, EH40, FH27S, FH32,FH36, FH40
100
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni
40Ferritic Low Temperature
UNS S31803 40Duplex Stainless
As at 10 April 2018 7Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Honqi Road, Lishan District,Anshan City,
HEAVY PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:hp318@sina.com Web http://www.ansteel.con.cnAll grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.Certificate Number: MD00/1869/0012/1 Expiry: 20/03/2018
Liaoning Province
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianNormal strength, Higher Strength 300SlabsSemi-FinishedNormal Strength, Higher Strength 320BilletsA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
Angang AreaAnshan City
MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email: zy-zb-111@163.comSlabs as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved.Concast billets approved to 320 x 410mm section size.Certificate No. MD00/2757/0009/1 Expiry date: 21/10/2020
A, B, D 20Normal StrengthHot Rolled CoilANGANG STEEL COMPANY LIMITED DalianAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
20Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
Anshan CityLiaoning Province
HOT STRIP MILL OF ANGANG STEEL COMPANY LIMITEDAngang Production Area,Tiexi District
Tel: +86 412 6757143 Fax: +86 412 6753575Email: agwanrui@163.comWeb http://www.ansteel.com.cnCertificate #: MD00/3301/0004/1 Expiry date: 01/01/2019
114024
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED Daliancarbon-manganese, carbon, carbon manganese 300Blooms/BilletsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40
100Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel5Ni, 9Ni 60Ferritic Low Temperature
115000 BayuquanYingkou City
BAYUQUAN 5500 HEAVY PLATE MILL
Tel: +86 417 8680153 Fax: +86 417 8680141email: liuyuan1360@163.com web: www.ansteel.com.cnCertificate No. MD00/3595/0004/1 Expiry date: 09/05/2018
Liaoning Province
A, B, D 20Normal StrengthSectionsANGANG STEEL COMPANY LIMITED DalianAH32, AH36, DH32, DH36 20Higher Strength
114021 Tiexi,Anshan City,
HEAVY SECTION PLANT OF ANGANG STEEL COMPANY LIMITE
Tel: +86 412 673 4836 Fax: +86 412 672 5766 email hp318@sina.com web www.ansteel.con.cn
Certificate No: MD00/4637/0001/1 Expiry Date: 01/12/2019
Liaoning Province,
As belowE.A.F./V.O.D./IngotSteelmakingANSTEEL STEEL CASTING CO., LTD. Daliancarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished
Anshan, Liaoning Province11042
West Side of Hongqi Road
el: +86 412 6765212/6765217 Fax: +86 412 6765218 Email to: ajk999@yahoo.com.cn Web http://www.angangzhongji.com.cn
Certificate #: MD00/4436/0001/1 Expiry date: 25/02/2018
As BelowB.O.S./E.A.F./Con CastSteelmakingANYANG IRON & STEEL CO., LTD. WuhanNormal strength 230SlabsSemi-FinishedA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 36Higher Strength360AR, 410AR, 460FG, 490FG, 510FG 36Boiler & Pressure Vessel360FG, 410FG 40A, B 12Normal StrengthSections
As at 10 April 2018 8Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Anyang CityHenan Province
Yindu District
Tel: +86 372 3120051 Fax: +86 372 3120177 email: 343062385@163.com web: www.anyang.com.cnCertificate #: MD00/2200/0010/1 Expiry date: 18/01/2019
A, B and D grades in the normalised condition approved for through thickness properties with Z25 and Z35 notation.
As belowB.O.S. / Con CastSteelmakingBAOSHAN IRON & STEEL CO., LTD. Shanghai PortAs belowB.O.S. / Ingotcarbon, carbon-manganese 500SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 500Blooms/BilletsA, B, D, E 130Normal StrengthPlatesAH40, DH40, EH40, FH27S, FH32, FH36 68Higher StrengthDH36S 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
AH42, AH46, AH50, AH55, AH62, AH69, DH42,DH46, DH50, DH55, DH62, DH69, EH42, EH46,EH50, EH55, EH62, EH69, FH40, FH42, FH46,FH50, FH55, FH62, FH69
160
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel9Ni 50Ferritic Low TemperatureLTAH40, LTDH40, LTEH40, LTFH27S, LTFH32,LTFH36, LTFH40
68
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36
80
A, B, D 22Normal StrengthHot Rolled CoilAH32, AH36 12Higher Strength460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22R5 210Chain Cable StockBars
No 885, Fujin RoadBaoshan District
Core Base
Tel +86 21 2664 5085 Fax +86 21 2664 4886
E-mail: zhangxiangkui@baosteel.com
Web:http://www.baosteel.com
Including all plate grades and thicknesses with specified through thickness properties (Z35)
Certificate #: MD00/1343/0019/1 Expiry date: 29/03/2019
Materials Quality Scheme Approved - MQS 038
Shanghai 201900
austenitic stainless steel, Fe-36Ni*E.A.F/A.O.D/L.A.F/ConCastSteelmakingBAOSTEEL SPECIAL METALS Co., LTD Shanghai PortFe-36Ni* 8Fe-Ni alloysPlates
Baoshan District,Shanghai.
No. 1269, Shuichan Road,
Tel: +86 - 21 - 2603 2450 Fax: +86 - 2603 2284
E-mail:
www.baosteel.com
Certificate No: MD00/4729/0001/1 Expiry Date: 30/10/2020
200940
As belowB.O.S. / Con CastSteelmakingBAOSTEEL ZHANJIANG IRON & STEEL Co., Ltd. Guangzhoucarbon, carbon-manganese 250SlabsSemi-FinishedD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
Dongjian Town, Donghai Island, ZhanjiangGuangdong Province
Baosteel Zhanjiang Iron & Steel Plant
Tel: +86 0759 3525503 Fax: +86 0759 3525555Email: Web: www.baosteel.comCertificate No.: MD00/4683/0001/1 Expiry Date: 24/07/2020
As at 10 April 2018 9Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D 14Normal StrengthSectionsCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAH27S, AH32, AH36 14Higher Strength
Meili TownChangshu City
No. 9 Jusha Road
Tel: +86 0512 5206 1085 Fax: +86 0512 5266 1141 Email: lttg@lttg.cn Web: http://www.lttg.cnCertificate #: MD00/3275/0005/1 Expiry date: 09/10/2018
Jiangsu Province 21551
As belowB.O.S. / Con CastSteelmakingCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAs belowE.A.F. / Con Castcarbon, carbon-manganese, alloy 26Ingots (tonnes)Semi-FinishedNormal Strength, Higher Strength 260BloomsNormal Strength, Higher Strength 200BilletsD 15Normal StrengthSectionsE 16A, B 20DH32, DH36, EH32, EH36 16Higher StrengthAH27S, AH32, AH36 20
Tonggang Industrial Park,Meili Town, Changshu City,
118 Hualian Road,
Tel.:+86 0512 5206 1085 Fax.: +86 512 5266 1141Email: lttg@lttg.cn Web: http://www.lttg.cn
Certificate #: MD00/3976/0003/1 Expiry date: 07/12/2017
Blooms as semi finished products nominal 340mm width x nominal 12000mm length Billet approval covers BOS/Concast billets to 200 x 310mm section size x 6000mm nominal length..
Jiangsu Province 215511
As belowB.O.S. / Con CastSteelmakingCHENGDE JIANLONG SPECIAL STEEL CO., LTD. Qingdaocarbon, carbon-manganese, Alloy 200Blooms/BilletsSemi-FinishedU2, U3 90Chain Cable StockBars
Ping-an-bao TownXinglong County
Tel.:+86 0314 5316388 Fax.: +86 314 5316389Email: yangdong@ejianlong.com Web: http://www.ejianlong.com
Certificate #: MD00/4550/0002/1 Expiry date: 10/02/2019
Chengde, Hebei
As belowB.O.S. / Con CastSteelmakingCISCO WuhanNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG 80
Changshou DistrictChongqing
Chongqing Iron and Steel Co., Ltd.Jiangnan Town (4100 Mill)
Tel: +86 23 6887 3543 Fax: +86 23 6887 3543email: zyflwy@163.com web: www.cqgt.comCertificate Number: MD00/3763/0007/1 Expiry date: 27/03/2019
A, B, D, E 40Normal StrengthPlatesCISCO WuhanAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
40Boiler & Pressure Vessel
Chongqing Iron and Steel Co., Ltd.Jiangnan Town (2700 Mill)Tel: +82 623 6887 3543 Fax: +82 623 6887 3543 Email: cqgt@163.com Web: http://www.cqgt.cnPlates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.Certificate Number: MD00/3982/0003/1 Expiry: 25/01/2018
As belowB.O.S. / Con CastSteelmakingDAYE SPECIAL STEEL CO., LTD. WuhanAs belowE.A.F./Ingot/Con Castcarbon, carbon-manganese, alloy 40Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 410Billetscarbon, carbon-manganese, alloy 650Barscarbon, carbon-manganese 190StructuralBarscarbon, carbon-manganese, alloy 250MachineryU1, U2, API-2F 110Chain Cable StockU3, R3S, R4 160
As at 10 April 2018 10Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Huangshi CityHubei Province
316 Huangshi Avenue
Tel: +86 714 629 7888 Fax: +86 714 629 7781 Email: chenlei7483@163.com Web: http://www.dayesteel.com.cn
Mooring grade bars (grade R4) are restricted in ingot cast condition to supply to Zhengmao Group Co., Ltd.Mooring grade bars (grade R3S) are restricted to supply to Foshan Marine Anchor Chain Ltd. (FMAC)The bars may supply in annealing, normalized or quench and temperted conditions when it is appropriate
Certificate Number: MD00/2493/0011/1 Expiry: 11/08/2020
Post code: 435001
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganeseE.A.F./Ingot/Con Castcarbon, carbon-manganese 5Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 450Blooms/Billetscarbon, carbon-manganese 200Barscarbon, carbon-manganese 200StructuralBarsU1, U2, U3 130Chain Cable Stock
Qiqihar CityHeilongjiang Province
BEIMEN SPECIAL STEEL CO., LTD.Fularji District
Tel: +86 452 680 1271 Fax: +86 452 680 1234 email: jiajunlin08@163.com web: www.bg.bmsteel.com
Certificate No: MD00/2907/0002/1 Expiry date: 29/07/2020
Carbon, Carbon-manganese, Alloy 27EAF/LRF/VD/IngotSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganese, alloy 27Ingots (tonnes)Semi-Finished
Wanghua District,Fushun City,
FUSHUN SPECIAL STEEL CO. LTD.,East No 8 Anshan Road,
Tel No: +86 413 668 9161-3668 Fax no: +86 413 6674090Web: www.dtsteel.comCertificate No MD00/3945/0003/1 Expiry date: 04/09/2020
Liaoning Province
carbon, carbon-manganese, alloy 100B.O.S. / IngotSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganese, alloy 100E.A.F. / Ingotcarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished
Dalian Dengshahe Coastal Industrial Zone,Jinzhou New District,
DALIAN SPECIAL STEEL CO., LTD.No. 18 South Hebin Road,
Tel: +86 0411 626 93145 Fax: +86 0411 626 93037web: www.dsteel.com
Certificate No: MD00/4651/0001/3 Expiry Date: 11/01/2020
Dalian, Liaoning Province,
As belowB.O.S. / Con CastSteelmakingFUJIAN SANSTEEL MINGUANG CO., LTD. GuangzhouNormal strength, Higher Strength 250SlabsSemi-FinishedA, B 36Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 30Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel360, 410 36
Middle Gongyezhong RoadMeilie District
Tel: +86 598 8205138 Fax: +86 598 8205435Email: hic099@126.com Web: www.fjsg.com.cnCertificate #: MD00/3587/0006/1 Expiry date: 26/04/2018
Sanming CityFujian Province
austenitic stainless steel, duplex stainless steelE.A.F/A.O.D/L.A.F/ConCastSteelmakingGANSU JIU STEEL GROUP WuhanAs below 220SlabsSemi-Finished304L, 316L, 321 40Austenitic StainlessPlatesUNS S31803, UNS 32205* 40Duplex Stainless304L, 316L, 321 12Austenitic StainlessHot Rolled Coil
No.12, East Xiongguan Road, Jiayuguan City,Gansu Province
HONGXING IRON & STEEL CO., LTD
Tel: +86 0937 6717023 Fax: +86 0937 6714841Email: mailto: bxgcxsk@jiugang.comWeb: http://www.jiugang.comCertificate No.: MD00/4708/0001/1 Expiry date: 05/09/2020
As at 10 April 2018 11Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingGUANGXI LIUZHOU GuangzhouA, B 36Normal StrengthPlatesAH27S, AH32, AH36 36Higher StrengthA, B 12Normal StrengthHot Rolled Coil
117 BeiqueLiuzhou
IRON & STEEL (GROUP) COMPANY
Tel: +86 (0)772 2596593 Fax: +86 (0)772 2592784email pzkkz@126.com web www.liuzousteel.com
Certificate #: MD00/2632/0007/1 Expiry date: 01/01/2018
Guangxi
As belowB.O.S. / Con CastSteelmakingHANBAO IRON & STEEL CO. LTD (HANSTEELGROUP)
Qingdao
Normal strength, Higher Strength 250SlabsSemi-Finished
A, B, D 18Normal StrengthHot Rolled Coil
AH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength
A, B, D 18Normal StrengthPlates from coils
AH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength
232,Fuxing Road,Handan,
Tel +86 310 6072202 Fax No. + 86 310 6072241Email longshengmin@mail.hgjy.cnWeb www.ligjt.com.cnCertificate No MD00/3874/0002/ 1 Expiry Date 09/01/2017
Hebei. 056015
As belowB.O.S. / Con CastSteelmakingHEBEI IRON & STEEL CO., LTD. QingdaoNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, DH27S, EH27S 38Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 50360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50
Handan CityHebei Province
Handan Branch232 Fuxing Road
Tel: +86 310 607 2202 Fax: +86 310 607 2241 Email: longzhengmin@163.com Web: http://www.hgjt.com.cnSlabs as semi-finished products nominal 1800mm width x nominal 3200mm length to the above maximum thickness.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied for approved grades supplied in the normalized conditionCertificate Number: MD00/1970/0010/1 Expiry: 03/03/2019
056015
As below 220B.O.S. / Con CastSteelmakingHEBEI JINGYE CUT DEAL CO., LTD. QingdaoNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D 30Normal StrengthPlatesAH27S, AH32, AH36, DH32, DH36 30Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel
Pingshan CountyShijiazhuang City
Nandian Town
Tel No +86 311 8287 3953 Fax No +86 311 82873988 Mob +86 158 3111 8888Email jingye@hbjyjt.comWeb www.hbjyjt.comCertificate No MD00/4022/0002/1 Expiry Date 08/05/2018
Hebei Province
As belowE.A.F. / Con CastSteelmakingHENGYANG VALIN STEEL TUBE CO., LTD. Wuhancarbon, carbon-manganese, alloy 800BilletsSemi-Finished
Hengyang CityHunan Province 421001
No. 10 Dalixincun
Tel: +86 734 8872188 Fax: +86 734 8873188
Email: hgscjf@163.com
Web: www.hysteeltube.com
Certificate #: MD00/3098/0003/1 Expiry date: 04/08/2019
As at 10 April 2018 12Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingHUNAN VALIN LIANYUAN IRON & STEEL CO.,LTD.
Wuhan
carbon, carbon-manganese 230SlabsSemi-Finished
A, B, D 25Normal StrengthHot Rolled Coil
A, B, D 25Normal StrengthPlates from coils
Huangnitang, LoudiHunan Province
Tel +738 8661473 Fax +7388663570Email: pmy@lysteel.comweb: www. lysteel.comCertificate #: MD00/3999/0002/1 Expiry date: 05/03/2018
Post Code: 417009
As belowE.A.F. / IngotSteelmakingINNER MONGOLIA NORTH Daliancarbon, carbon-manganese, alloy 8Ingots (tonnes)Semi-Finished
Baotou CityInner Mongolia
HEAVY INDUSTRIES GROUP CO., LTD.Binggong Road, Qingshan District
Tel No:+86 472 338 5318 Fax No: +86 472 332 3346email: 18647994480@163.com Including semi-finished as-forged bars to 8.5 tonnes in carbon, carbon-manganese and alloy steel for further processing by forging.
Certificate No: MD00/3099/0006/1 Expiry date: 06/08/2019
014033
carbon 20Structural SectionsSeamless HollowJIANGSU JIEDA SPECIFIC NEW MATERIAL CO LTD Jiangyin
No. 98 Gangcheng Road,Jiangyin City,
Jiangyin Plant
Tel No: + 00 86-510-8668775 Fax No: + 00 86-510-86687775/+00 510-86687229Email: chezhongnan@jsjieda.comWebsite: www.jsjieda.com
Certificate No. MD00/4442/0002/01 Expiry Date: 17/01/2021
Jiangsu Province. 214400
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP NantongAs belowE.A.F. / Con Castcarbon, carbon-manganese 200BloomsSemi-Finishedcarbon, carbon-manganese 150Billetscarbon, carbon-manganese 500Barscarbon, carbon-manganese 100StructuralBarscarbon, carbon-manganese 100MachineryU2 140Chain Cable StockU3 210
Huai'an CityJiangsu Province
HUAIGANG SPECIAL STEEL CO., LTDNo. 188 South Xi'an Road
Tel: +81 517 83033307 Fax: +81 517 83033307 Mobile: +861536590 1758 Email:sundawen@163.com
The approval for rolled bars over 60mm diameter is for steel manufactured by the B.O.S. / Con Cast route.Bars for chain cable stock are intended for final heat treated conditions; Grade U2 normalized; Grade U3 quenched and tempered.Chain cable stock bars may be accepted up to 250mm diameter may be accepted for further processing for forged chain cable fittings.Blooms, billets and bars as semi finished-products are approved for further processing for rolled products; blooms nominal maximum width 200mm x nominalmaximum length 12000mm; billets nominal maximum width 150mm x nominal maximum length 12000mm; bars nominal maximum length 12000mm; to theabove maximum thicknesses.Certificate Number: MD00/3240/0005/1 Expiry: 13/06/2015
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Jinfeng TownZhangjiagang City
Hongfa Steel PlantSteelmaking Plant Number 1
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email: ctoec@shagang.cn Web http://www.sha-steel.com
Certifcate Number: MD00/3127/0009/1 Expiry date: 27/10/2019
Materials Quality Scheme Approved - Approval No. MQS069
Jiangsu Province 215625
As at 10 April 2018 13Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 100Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, AH40, AH42, AH46,AH50, AH55, AH62, AH69, DH27S, DH32,DH36, DH40, DH42, DH46, DH50, DH55, DH62,DH69, EH27S, EH32, EH36, EH40, EH42, EH46,EH50, EH55, EH62, EH69, FH27S, FH32, FH36,FH40, FH42, FH46, FH50, FH55, FH62, FH69
100Higher Strength
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
Hongfa Steel PlantSteel Plate Mill Line No. 1
Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: ctotec@shagang.cn Web: http://www.sha-steel.com Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.Plates in the quenched and tempered supply condition >70mm thickness are accepted for approved applications only.Certificate No. MD00/3388/00010/1 Expiry date: 27/10/2019
Materials Quality Scheme Approved - Approval No. MQS069
Jiangsu Province, 215625
A, B, D, E 60Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH46S, DH27S, EH27S, EH46S, FH27S,FH32, FH36, FH40, FH46S, AH42S, DH42S,EH42S, FH42S, AH50S, DH50S, EH50S, FH50S,AH55S, DH55S, EH55S, FH55S, DH46S
60Higher Strength
EH47 80AH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40
85
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,490FG, 510FG
40Boiler & Pressure Vessel
LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40
40Ferritic Low Temperature
Hongfa Steel PlantSteel Plate Mill Line No. 2Tel +86 0512 5856 8791 Fax: +86 0512 5855 8900 Email: ctotec@shagang.cn Web: http://www.sha-steel.com All the above grades may be produced with specified through thickness tensile properties when manufactured and tested in accordance with LR Rules for'Plates with Specificed Through Thickness Properties'.Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in AH32 and AH 36 as rolled to 2800 x 11,000 and approved in the "as welded "conditionCertificate No. MD00/3913/0009/1 Expiry date: 27/10/2019
Materials Quality Scheme Approved - Approval No. MQS069
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Hongfa Steel PlantSteelmaking Plant Number 2
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email: ctoec@shagang.cn Web http://www.sha-steel.com
Certifcate Number: MD00/3923/0005/1 Expiry date: 27/10/2019
Materials Quality Scheme Approved - Approval No. MQS069
Jiangsu Province 215625
A, B, D, E 40Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
Zhajiagang City
Hongfa Steel Plant3500mm Medium Plate Mill
Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: ctotec@shagang.cn Web: http://www.sha-steel.com Certificate No. MD00/4710/0002/1 Expiry date: 18/06/2020
Jiangsu Province, 215625
Alloy 83EAF/LRF/VD/IngotSteelmakingJIANGSU SUNAN HEAVY MACHINERY JiangyinCarbon, Carbon-manganese 150
As at 10 April 2018 14Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Economic & Technology Development Zone,Changshu City,
TECHNOLOGY CO LTD.No.6 XingGang Road,
Tel: +85 0512 52275923 Fax: +86 0512 51923689email: xufeng@snzbjt.com
Certificate No. MD00/4334/0002/1 Expiry Date: 09/06/2020
Jiangsu Province,
A, B 40Normal StrengthSectionsJIANGYIN BOFENG IRON & STEEL CO., LTD. JiangyinAH27S, AH32, AH36 40Higher Strength
Huaxicun Industrial ZoneJiangyin City
Tel: +86 13585066431 Fax: +86 510 8621 7672 Email: office2@bofengsteel.com Web: http://www.bofengsteel.cnThe approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.Certificate Number: MD00/4031/0002/1 Expiry: 05/06/2018
Jiangsu Province
As belowE.A.F. / IngotSteelmakingJIANGYIN HUAQIANG SPECIAL STEEL Jiangyincarbon, carbon-manganese, alloy 32Ingots (tonnes)Semi-Finished
No. 18, Biangang Road,Huaxi, Jiangyin City,
CASTING & FORGING THERMOELECTRIC CO., LTD.
Tel: +86 510 862 10013 Fax: +86 510 862 03428 Mobile 0086 13812 582903 Email: mj2_hq@163.com Ingots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing forforgings.Certificate Number: MD00/4013/0002/1 Expiry: 22/04/2018
Jiangsu Province, 214421,
carbon, carbon-manganese 34Structural SectionsSeamless HollowJIANGYIN TONGDA SPECIAL PIPEMANUFACTURE Co., Ltd.
Jiangyin
No. 18 Qiaohuang RD, Xiake TownJiangyin City
Tel: +86 (0)510 8657 3666 Fax: +86 (0)510 8656 0685email: jytongda@126.com web: www.jytongda.comCertificate #: MD00/3853/0004/4 Expiry date: 02/11/2019
Jiangsu Province, 214408
As BelowB.O.S./E.A.F./Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
Normal strength 250SlabsSemi-Finished
carbon, carbon-manganese, alloy 390Blooms
carbon, carbon-manganese, alloy 900Semi-finished ProductsBars
carbon, carbon-manganese, alloy 180Structural
carbon, carbon-manganese, alloy 180Machinery
R4S 150Chain Cable Stock
U1, U2, U3 180
R3, R3S, R4 230
297, Bin Jiang East Road
Tel: +86 510 80676377 Fax: +86 510 86195042
E-mail: kangzhiqing@jyxc.com
Web: http://www.jyxc.com
Certificate Number: MD00/2306/0018/1 Expiry: 24/09/2019
Jiangsu province 214429
As belowB.O.S. / Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
Normal strength, Higher Strength 300SlabsSemi-Finished
A, B, D, E 50Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
As at 10 April 2018 15Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office3500 Plate Mill
Tel: +86 510 80676377 Fax: +86 510 86195042
E-mail: kangzhiqing@jyxc.com
Website: www.jyxc.com
Certificate Number: MD00/3857/0007/1 Expiry date: 24/09/2019
Jiangsu Province 214429
A, B, D, E 80Normal StrengthPlatesJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
DH40, EH40, FH27S, FH32, FH36, FH40 60Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
120
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
5Ni, 9Ni 50Ferritic Low Temperature
4300 Plate MillTel: +86 0510 80676377 Fax: +86 0510 6195042
E-mail: kangzhiqing@jyxc.com
Website: http://www.jyxc.com
Plates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width. Plates in the TM+Acc supply condition are restricted to thickness from 16mm to the maximum thickness shown above.Z35 designation for through thickness properties may be added to all plates in the above supply conditions.
Certificate Number: MD00/3973/0005/1 Expiry date: 08/01/2021
carbon, carbon-manganese 16Structural SectionsFabricated SectionsJIGANG GROUP Co. LTD Qingdao
Licheng District,Jinan,
Airport Road,
Tel: +86 531 88842106 Fax: +86 531 62325025
E-mail: zhucy_iglw@163.com
Website: www.jigang.com.cn
Certificate No. MD00/4595/0001/1 Expiry Date: 11/07/2019
Shangdong
304L, 316L 80Austenitic StainlessPlatesKUNSHAN DAEKYUNG STAINLESS STEEL CO.,LTD
Shanghai Port
Kunshan Economy Technology Development ZoneKunshan
No. 66 Longdeng Road
Tel:+86 512 57900998-8450 Fax: +86 512 57700372
E-mail: wenyu.huang@ks.shdlgroup.com
Website: www.kdkcsteel.com
Certificate #: MD00/3479/0004/1 Expiry date: 06/06/2020
Jiangsu Province
As belowB.O.S. / Con CastSteelmakingLAIWU STEEL GROUP LTD. YINSHAN SECTIONSTEEL CORPORATION
Qingdao
As below 300SlabsSemi-Finished
carbon, carbon-manganese 300Billets
A, B, D, E 80Normal StrengthPlates
DH40, EH40, FH32, FH36, FH40 50Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36 80
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
As at 10 April 2018 16Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Gangcheng district,Laiwu,
Shuangquan Road,
Tel: +86 634 6821211 Fax: +86 634 6820824 email: lwmw001@126.com web: www.laigang.net
Certificate #: MD00/3855/0006/1 Expiry date: 06/11/2019
Shandong
As belowB.O.S. / Con CastSteelmakingMAANSHAN IRON & STEEL COMPANY LIMITED NanjingNormal strength, Higher Strength 220SlabsSemi-FinishedA, B 25Normal StrengthPlatesAH32, AH36, DH32, DH36 25Higher Strength360AR, 410AR 25Boiler & Pressure Vessel
No.8 Jiuhua West Road,Maanshan City
Tel: +86 555 287 7110 Fax: +86 555 2886 904 Email: jjsskk2005@yahoo.com.cn.Web http://www.magang.com.cnCertificate #: MD00/0965/0008/1 Expiry date: 07/10/2018
Anhui Province PC:243000
Carbon, Carbon-manganese, Alloy 25EAF/LRF/VD/IngotSteelmakingMAANSHAN XINLONG SPECIAL STEEL CO., LTD. Jiangyincarbon, carbon-manganese, alloy 25Ingots (tonnes)Semi-Finished
Taibai Industrial,Dangtu town,
Tel: + 0555 667 5062 Fax: + 0555 667 5062
Certificate No: MD00/4402/0001/1 Expiry Date: 03/11/2017
Maanshan City,
As belowB.O.S. / Con CastSteelmakingMINMETALS YINGKOU MEDIUM PLATE CO., LTD. DalianNormal strength, Higher Strength 350SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH27S, DH27S, EH27S 40Higher StrengthAH50, AH55, DH50, DH55, EH50, EH55 50AH42, AH46, DH42, DH46, EH42, EH46 80AH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40, FH32, FH36, FH40
100
360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
Laobian DistrictYingkou City
No 1 Fanrong Road, Yejin Street
Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057 Email mailto:jszlb-wkyg@163.comWeb :www.wkyg.comPlates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2585/0009/1 Expiry date: 30/07/2020
Liaoning Province
As belowB.O.S. / Con CastSteelmakingNANJING IRON & STEEL CO., LTD. NanjingAs belowE.A.F. / Con CastNormal strength, Higher Strength 220SlabsSemi-FinishedNormal Strength, Higher Strength 320BloomsNormal Strength, Higher Strength 150BilletsA, B, D, E 100Normal StrengthPlatesAH27S, DH27S, EH27S, FH27S 60Higher StrengthEH47 80AH32, AH36, AH40, AH42, AH46, AH50, AH55,AH62, AH69, DH32, DH36, DH40, DH42, DH46,DH50, DH55, DH62, DH69, EH32, EH36, EH40,EH42, EH46, EH50, EH55, EH62, EH69, FH32,FH36, FH40, FH42, FH46, FH50, FH55, FH62,FH69
100
360AR, 410AR, 360, 410 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100LTAH27S, LTDH27S, LTEH27S, LTFH27S 40Ferritic Low TemperatureLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36, LTFH40, 5Ni, 9Ni
60
U1, U2, U3 180Chain Cable StockBars
As at 10 April 2018 17Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
XieJiaDianLuhe District
Nanjing Works
Tel: +86 25 5707 3657 Fax: +86 25 5707 4341 Email :wangwuyi@njsteel.com.cn Web:http://www.njsteel.com.cn
Plates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades
U2, U3 bars at 80mm diameter or less are produced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.
Billets and blooms approved upto the above maximum thickness, 480mm width and nominal 12000mm length.
Slabs approved upto the above maximum thickness, 2510mm width and nominal 4000mm length.
Certificate Number: MD00/1065/0021/1 Expiry date: 12/10/2019
Nanjing, Post Code: 210035
As belowB.O.S./Ingot/Con CastSteelmakingNANYANG HANYE SPECIAL STEEL CO., LTD., Wuhancarbon, carbon-manganese, alloy 48Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 300SlabsA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 100Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel
Xixia County,Nanyang City,
Huiche Town Industry Area,
Tel No: +86 377 697 65211 Fax No: +86 377 697 65333Email: zhaoyuan_521@sohu.comWebsite: www.elongcheng.comCertificate No: MD00/3969/0002/1 Expiry date 01/01/2018
Henan Province
304L, 304LN, 316L 12Austenitic Stainless SteelPlates from coilsOUTOKUMPU STAINLESS STEEL (CHINA) Co., Ltd. Shanghai Port
KunshanJiangsu Province
No. 288, Chenfeng RoadYushan Town
Tel No: +86 512 50120382 Fax No: +86 512 50120392
Certificate No: MD00/4422/0001/1 Expiry date: 26/01/2018
215300
Alloy 25EAF/LRF/VD/IngotSteelmakingPANGANG GROUP WuhanCarbon, Carbon-manganese 40alloy 25Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 40alloy 25ESR Ingotscarbon, carbon-manganese 300Barsalloy 390carbon, carbon-manganese, alloy 390StructuralBarscarbon, carbon-manganese, alloy 390Machinery
Jiangyou City,Sichuan Province,
JIANGYOU CHANGCHENG SPECIAL STEEL CO., LTD.,No.195, Jiangdong Road,
Tel No: +86 816 365 087 Fax No: +86 816 3650463Email zjbzgk@163.comWeb: http://www.cssc.com.cnCertificate No: MD00/4201/0002/1 Expiry date: 12/07/2019
621701
E 32Normal StrengthPlatesQINHUANGDAO SHOUGANG PLATE MILL CO.,LTD.
Dalian
A, B, D 35
AH27S, AH32, AH36, DH27S, DH32, DH36 32Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 32Boiler & Pressure Vessel
360AR, 410AR 35
No. 409 Jianshe StreetQinhuangdao City
Tel: +86 0335 3011421 3100 Fax: +86 0335 3014693email: shouqinshichangbu@163.com
Certificate #: MD00/2097/0009/1 Expiry date: 04/07/2018
Hebei Province
As at 10 April 2018 18Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingQINHUANGDAO SHOUQIN METAL MATERIALSCO., LTD.
Dalian
carbon, carbon-manganese 400SlabsSemi-Finished
D 50Normal StrengthPlates
A, B 100
FH32, FH36, FH40 40Higher Strength
AH40, DH40, EH27S, EH32, EH36, EH40 60
AH36, DH27S, DH36 80
AH27S, AH32, DH32 100
360AR, 410AR 16Boiler & Pressure Vessel
360, 410 32
510FG 80
360FG, 410FG, 460FG, 490FG 100
Haigang DistrictQinhuangdao
Duzhuang
Tel +86 0335 6082696 Fax +86 010 6082690 Email: market@sq.shougang.com.cn web www.shouqin.com.cn
Certificate No: MD00/3136/0009/1 Expiry Date: 00/02/2020
All plate grades and thicknesses with through thickness properties, notations Z25 and Z35 may be added.
Hebei Province 066326
As belowB.O.S. / Con CastSteelmakingRIZHAO STEEL WIRE CO., LTD Qingdaocarbon, carbon-manganese 230SlabsSemi-FinishedA, B 25Normal StrengthHot Rolled CoilA, B 25Normal StrengthPlates from coils
No. 600, Yanhai Road, RizhaoShandongTel: +86 633 6188070 Fax: +86 633 6188155email. jzwanggang@rizhaosteel.com web: www.rizhaosteel.comCertificate #: MD00/3843/0003/1 Expiry date: 05/10/2019
As belowE.A.F. / IngotSteelmakingSANXIN HEAVY INDUSTRY MACHINERY CO., LTD Jiangyincarbon, carbon-manganese, alloy 40Ingots (tonnes)Semi-Finished
Jiaze,Wujin, Changzhou,
Xia Xi North Road,
Tel No +86 519 83685579 Fax +86 519 83585579email: sxzgjx@sina.cn web www.sanxinzg.comCertificate No MD00/4184/0002/1 Expiry Date 17/06/2019
Jiangsu, 213148
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSGIS SONGSHAN CO., LTD Guangzhoucarbon, carbon-manganese, alloy 270SlabsSemi-Finishedcarbon, carbon-manganese 425Bloomscarbon, carbon-manganese, alloy 170BilletsA, B, D, E 60Normal StrengthPlatesAH40, DH40, EH40 36Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60
360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60U3 150Chain Cable StockBars
Qujiang DistrictShaoguan City
Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066 email ly73@21cn.com
Certificate #: MD00/2175/0011/1 Expiry date: 21/11/2018
CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels
Guangdong 512123
As at 10 April 2018 19Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingSHANDONG IRON & STEEL CO., Ltd. Qingdaocarbon, carbon-manganese 270SlabsSemi-FinishedE 50Normal StrengthPlatesA, B, D 60AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH32,FH36, FH40
60Higher Strength
360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60A, B 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36 12Higher Strength
Jinan, 250101Shandong Province
JINAN COMPANY21, Gongye Bei Road
Tel +86 531 8886 6396 Fax +86 531 8898 8351 email: jigangleike@163.com web: www.jigang.com.cnCertificate #: MD00/0799/0014/1 Expiry date: 14/10/2019
As belowB.O.S. / Con CastSteelmakingSHANDONG IRON & STEEL CO., Ltd. QingdaoAs belowE.A.F. / Con CastU2, U3 160Chain Cable StockBars
Gang Cheng DistrictLaiwu City
LAIWU COMPANYNo.99 Fuqian Street
Tel: +86 634 7920316 Fax: +86 634 6820824email: lgyxm@163.com web: www.laigang.net
Bar over 130mm diameter is approved using EAF process route only.
Certificate No.: MD00/4389/0003/1 Expiry Date: 06/10/2020
As belowB.O.S. / Con CastSteelmakingSHANDONG SHOUGUANG JUNENG SPECIALSTEEL CO, LTD.
Qingdao
Carbon, Carbon-Manganese 310Rolled BilletsSemi-Finished
carbon, carbon-manganese 600Billets
carbon, carbon-manganese 130StructuralBars
carbon, carbon-manganese 130Machinery
U1 130Chain Cable Stock
U2, U3 160
No. 9 Tegang RoadShouguang, Shangdong Province
Tel: +86 532 5186159 Fax No. +86 532 5186789E-mail: zwsun2008@163.comwww.sgjntg.comCertificate No: MD00/3260/0006/1 Expiry date: 21/09/2018
262711
austenitic stainless 130BarsSemi-FinishedSHANGHAI BAIHE WALSIN LIHWA Shanghai Port
No. 2402 Qingsong RoadBaihe Town, Qingpu District
SPECIALTY STEEL PRODUCTS Co., Ltd.
Tel: +86 21 59746686 Fax: +86 21 59746686
Certificate No: MD00/4450/0001/1 Expiry Date: 21/03/2018
Approval for austenitic grades covers types 304L, 316L, 321, 347.
Shanghai (201709)
A, B, D 20Normal StrengthSectionsSHANGHAI BAOSTEEL SECTION STEEL CO., LTD. Shanghai PortAH32, AH36 20Higher Strength
No. 3801, Huaxiang RoadShanghai
Tel No: +86 21 6221 1362 Fax No: +86 21 6221 9842Email baosteelclass@163.comCertificate No. MD00/4686/002/1 Expiry date: 08/08/2020Approved for ERW welded section only
201107
As at 10 April 2018 20Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Carbon, Carbon-manganese, Alloy 200EAF/LRF/VD/IngotSteelmakingSHANGHAI ELECTRIC SHMP CASTING &FORGING CO., LTD.
Shanghai Port
Minhang District1800 Jiangchuan Road
Tel: +86 21 34098660 Mob: +86 1891 780 4183email shenwj@shanghai-electric.com web: www.sshanghai-electric.com
Certificate #: MD00/1345/0003/1 Expiry date: 09/04/2020
200245
As belowE.A.F./A.O.D./Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianAs belowE.A.F/A.O.D/IngotAs below 8Ingots (tonnes)Semi-FinishedAs below 200SlabsAs below 230Billets304L, 316L 20Austenitic StainlessPlatesUNS S31803 40Duplex Stainless
Jiancaoping Street No. 2Taiyuan030003Taiyuan
Stainless Steel Hot Rolling Mill
Tel No: +86 351 3012029 Fax No: +86 351 3017893 Mob: 13503502921
All plate grades with specified through-thickness properties
Email: Zhanghy02@tisco.com.cn Web: http://tgbx.tisco.com.cn Certificate No. MD00/3185/0009/1 Expiry date: 14/08/2020
As belowB.O.S. / Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianNormal strength, Higher Strength 200SlabsSemi-FinishedA, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360FG, 410FG 25Boiler & Pressure VesselA, B, D 25Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 25Higher Strength410 FG, 360 FG 25Boiler and Pressure Vessel
Jiancaoping Street No. 2Hot Strip Mill
Tel: +86 351 2132943 Fax: +86 351 2137664 Mobile: +86 135 0350 2921Email: Zhanghy02@tisco.com.cn Web: http: //www.tisco.com.cn Slabs as semi finished products 2310mm nominal width and 12000mm nominal length to the above maximum thickness are approved for further processing forrolled products.Certificate #: MD00/3507/0004/1 Expiry date: 27/07/2020
A, B, D 40Normal StrengthPlatesSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianAH32, AH36, DH32, DH36 40Higher Strength304L, 316L, 304*, 316* 60Austenitic StainlessUNS S31803 40Duplex Stainless
Qiaodong Street No.3Linfen City
Linfen Heavy Plate Mill
Tel: +86 351 3017667 Fax: +86 351 3017893 Email: yangfei@tisco.com.cn Web: http:// www.tisco.com.cn Certificate No MD00/3688/0005/1 Expiry date 07/07/2015
Shanxi Province
Carbon, Carbon-manganese, Alloy 12EAF/LRF/VD/IngotSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian
No.2 Jian Caoping Street,Taiyuan City,
Section Steel Plant,
Tel: +81 (0)351 2130108 Fax: +81 (0)351 2317595
E-mail: zhanghy02@tisco.co.cn
Website: tisco.com.cn
Certificate No. MD00/4240/0002/1 Expiry Date: 14/10/2019.
Shanxi Province,
As belowE.A.F. / IngotSteelmakingSHI GANG JING CHENG EQUIPMENTDEVELOPMENT
Dalian
carbon, carbon-manganese, alloy 132Ingots (tonnes)Semi-Finished
As at 10 April 2018 21Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
No. 1 Xinlian Street,Yingkou,
AND MANUFACTURING CO., LTD.
Tel: +86 0417 3257800 Fax: +86 0417 3257905email: 18904979981@163.com web: http://www.cyedm.com.cnCertificate #: MD00/4234/0004/1 Expiry date: 08/10/2019
Liaoning Province,
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSHIJIAZHUANG I & S CO., LTD. Daliancarbon, carbon-manganese 150StructuralBarscarbon, carbon-manganese 150MachineryU1, U2, U3 150Chain Cable Stock
Shijiazhuang CityHebei Province
No. 363 Heping E Road
Tel: +86 (0)311 869 12562 Fax: +86 (0)311 869 13368Email: sunjp_sggs@126.comCertificate #: MD00/3315/0004/1 Expiry date: 05/02/2019
As belowB.O.S. / Con CastSteelmakingSHOUGANG JINGTANG UNITED IRON & STEELCO., LTD.
Qingdao
carbon, carbon-manganese 250SlabsSemi-Finished
A, B, D 18Normal StrengthHot Rolled Coil
AH32, AH36, DH32, DH36 18Higher Strength
A, B, D 18Normal StrengthPlates from coils
AH32, DH32, AH36, DH36 18Higher Strength
Caofeidian Industrial Zone, Tangshan
Tel: +86 315 8872636 Fax: +86 315 8872606 email: uha_w@126.com web: www.sgjsteel.com
Certificate #: MD00/3820/0003/1 Expiry date: 19/11/2019
Post Code: 063200
As belowB.O.S. / Con CastSteelmakingSHOUGANG QIAN'AN IRON & STEEL COMPANY Daliancarbon, carbon-manganese, alloy 230SlabsSemi-FinishedA, B, D 18Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 18Boiler & Pressure VesselA, B, D 18Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength
West Industrial DistrictQian'an City
No. 025, Zhao'an Road
Tel: +86 315 7703232 Fax: +86 315 7703136 web http://www.sggf.com.cn
Certificate #: MD00/3488/0005/1 Expiry date: 07/07/2020
Hebei, 064404
Carbon, Carbon-manganese, Alloy 8EAF/LRF/VD/IngotSteelmakingSICHUAN LIUHE FORGING CO., LTD. Wuhan
Baolun Road(W), Henan Industrial ParkJiangyou City
Tel No: +86 0816 3456788 Fax No: +86 0816 3521398Email: bk.liwei'@gmail.comCertificate No: MD00/4176/0002/1 Expiry date 08/06/2019
Sichuan Province
A, B, D, E 20Normal StrengthSectionsSUQIAN NANJING IRON & STEEL NanjingAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36
20Higher Strength
No.89 Jingshan Road,Suyu District,
JINXIN STEEL ROLLING Co., Ltd.
Tel; +86 527 844 53907 Fax: +86 527 844 80094 Mob: +86 (0)152 9832 5588 email: aqhw333@sina.com
Certificate: MD00/3741/0007/1 Expiry date: 15/12/2020
Suqian City, Jiangsu,
As belowE.A.F. / Con CastSteelmakingSUZHOU SUXIN SPECIAL STEEL CO., LTD. Shanghai PortU1, U2, U3 120Chain Cable StockBars
Huashan, Tong An, SuzhouJiangsu
Tel: +86 0512 8887 8163 Fax: +86 0512 88877273email: wangtao@sugang.com.cn web: www.sugang.com.cn
Certificate #: MD00/3492/0003/1 Expiry date: 13/07/2017
Post Code: 215151
As at 10 April 2018 22Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese 186Ingots (tonnes)Semi-FinishedTAI YUAN HEAVY INDUSTRY CO. LTD. Wuhan
No.53, Yuhe Street,Wanbailin District, Taiyuan City,
Tel +86 351 636 2835 Fax: +86 351 636 1424
E-mail: liubin_8440@163.com.
Website: www.tyhi.com.cn
Certificate #: MD00/3412/0005/1 Expiry date: 30/09/2019
Shanxi Province, 030024,
As belowB.O.S. / Con CastSteelmakingTANGSHAN HEAVY PLATE CO., LTD. Qingdaocarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
Leting County,Tangshan City,
Lingang Industrial Park
Tel Nos: +86 315 4958145, +86 315 4958135 Fax No: +86 315 4959153Email chuanbin04@126.com@163.com (enquiries), zhaowenge1966@126.com (orders)
Certificate #: MD00/3475/0005/1 Expiry date: 30/05/2020
Hebei
A, B 24Normal StrengthSectionsTANGSHAN SHENGCAI STEEL CO., LTD. DalianAH32, AH36 24Higher Strength
Angezhuang Town,Luannan County, Tangshan City,
South of Xinghonglin Village
Tel No: +86 315 245 0855 Fax No: +86 315 445 1116email scgtbgs@126.com web: www.731147959@qq.com
Certificate No: MD00/4131/0003/1 Expiry Date 18/03/2019
Hebei Province
As belowB.O.S. / Con CastSteelmakingTANGSHAN YANSHAN IRON & STEEL CO., LTD. DalianNormal strength, Higher Strength 250SlabsSemi-FinishedNormal Strength 150Billets
The West Side of Qianan Railway StationQianan City
Tel: +86 315 7769 566 Fax: +86 315 7769 566E-mail: hesong44@126.comBillets nominal maximum width 150mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; slabsnominal maximum width 1,800mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; are approved forfurther processing for rolled products in the detailed strength levels.Certificate Number: MD00/3648/0005/1 Expiry: 08/06/2018
Hebei Province (064403)
As belowB.O.S. / Con CastSteelmakingTIANJIN IRON AND STEEL GROUP CO. LTD. Qingdaocarbon, carbon-manganese, alloy 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength
Dongli DistrictTianjin
398 Jintang Road
Tel:+86 22 24706052 Fax: +86 22 24706052 Email: TGRZ166@yeah.netweb: www.tgsteel.comCertificate #: MD00/3485/0005/1 Expiry date: 30/06/2020
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingTIANJIN PIPE (GROUP) CORPORATION Daliancarbon, carbon-manganese, alloy 400BloomsSemi-Finished
No 396, Jintang Road
Tel No: +86 22 2480 2296 Fax no: +86 22480 1291
Email zhangyh@tpco.cn
Web: www.tpco.com
Certificate No MD00/3361/0005/1 Expiry Date 28/07/2019
300301
carbon, carbon-manganese 90E.A.F. / IngotSteelmakingTIANJIN TIANZHONG GIANT HEAVY INDUSTRYCO., LTD.
Qingdao
As at 10 April 2018 23Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Xiditou TownBeichen District
No. 609, Jinyu Road
Tel:+86 (0)22 86885730 Fax: +86(0)22 8688 5673emsil: jtzgdz@163.com web: www.jiangtian.cnCertificate No: MD00/4094/0003/1 Expiry date: 24/11/2018
Tianjin
A, B 15Normal StrengthSectionsTIANJIN YONGHENG ENTERPRISE CO., LTD. DalianAH32, AH36 15Higher Strength
No. 5, Gangtuan West RoadDaqiu Town, Jinghai County
Tel:+86 (0)2228899180 Fax: +86(0)2228899185 Email:wy8770@163.com Web:http://www.tjyhsy.comCertificate #: MD00/3953/0002/1 Expiry date: 24/09/2017
Tianjin, 301606
alloy 160E.A.F. / IngotSteelmakingTONGYU HEAVY INDUSTRY Co., Ltd Qingdaocarbon, carbon-manganese 200alloy 160Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 200
Dezhou City,Shandong Province,
National High-Tech Industry Area,Yucheng City,
Tel: +86 534 7520690 Fax: +86534 7521470Certificate No. MD00/3998/0003/1 Expiry date: 28/02/2018
As belowB.O.S. / Con CastSteelmakingWISCO WuhanAs below 250SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360, 410 12Boiler & Pressure VesselA, B, D 25Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 25Higher Strength360, 410 12Boiler and Pressure Vessel
QingshanWuhan
Wuhan Iron and Steel Co., Ltd.Changqian
Tel: +86 27 8689 1629 Fax: +86 27 8689 2413
E-mail: zhangtao2010@foxmail.com
web: www.wisco.com.cn
Certificate No: MD00/1683/0011/1 Expiry date: 19/11/2019
carbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-FinishedWUHAN HEAVY INDUSTRY Wuhan
Qingshan District
CASTING AND FORGING CO., LTD.1 Wudong Street
Tel No:+86 027 6886 1813 Fax No: +86 027 6886 1810 Mob :+86 13720291417Email wh471zg@163.comWeb www.whzg.com.cnCertificate No: MD00/1681/0003/1 Expiry date: 02/04/2020
Hubei
As belowB.O.S. / Con CastSteelmakingWUHAN IRON & STEEL GROUP WuhanAs below, Normal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 90Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 90Boiler & Pressure Vessel
No. 215 Wuchang DadaoEzhou City
ECHENG IRON & STEEL CO., LTD.
Tel: +86 711 3233225 Fax: +86 711 3233225 Email: 13986400824@qq.comwww.ecsteel.com.cnCertificate #: MD00/3931/0005/1 Expiry date: 01/07/2017
Z25 ad Z35 through thickness properties for plates of approved grades in the TM+Acc and Normalized conditio
Hubei Province, 436002
As at 10 April 2018 24Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / IngotSteelmakingWUHAN ZHONGYE MACHINERY WHOLE SETEQUIPMENT
Wuhan
carbon, carbon-manganese, alloy 18Ingots (tonnes)Semi-Finished
Lingcheng Road No. 2Lingxiang Town, Daye City
Gourp Co., Ltd.DAYE BRANCH
Tel: +86 0714 370 2019 Fax: +86 0714 370 2196 Email : ZG1819ZG@163.comCertificate #: MD00/4242/0001/1 Expiry date: 28/10/2016
Hubei Province
As belowE.A.F./Ingot/Con CastSteelmakingWUYANG IRON & STEEL COMPANY LTD. WuhanA, B, D, E 150Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
AH62, AH69, DH62, DH69, EH62, EH69, FH62,FH69
180
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
Henan ProvinceP.N: 462500
Wugang City
Tel: +86 375 811 1230 Fax: +86 375 811 4006E-mail: wgzhangweijun@163.comPlates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2044/0010/1 Expiry date: 25/03/2017
A, B, D, E 100Normal StrengthPlatesWUYANG IRON & STEEL COMPANY LTD. WuhanFH32, FH36, FH40 50Higher StrengthAH27S, AH32, AH36, AH40, AH42, AH46,AH50, AH55, AH62, AH69, DH27S, DH32,DH36, DH40, DH42, DH46, DH50, DH55, DH62,DH69, EH27S, EH32, EH36, EH40, EH42, EH46,EH50, EH55, EH62, EH69, FH42, FH46, FH50,FH55, FH62, FH69
100
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel9Ni 40Ferritic Low Temperature
Wugang City,Henan Province,
Wuyang New Wide and Heavy Steel Plate Co Ltd
Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: wgzhangweijun@163.comPlates with specified through thickness properties in listed grades of normal and higher strength steels 9NiCertificate No. MD00/3714/0006/1 Expiry Date 24/03/2020
PN 462500
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingXINING SPECIAL STEEL CO., LTD. Wuhancarbon, carbon-manganese, alloy 12Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 18ESR Ingotscarbon, carbon-manganese, alloy 250Semi-finished ProductsBars
No. 52 Chaidamu West RoadXining
Tel: 0086 0971 529 9294 Fax: 0086 0971 529 9407 Email: cyuian@sina.comWeb: www.xntg.comCertificate #: MD00/3798/0003/1 Expiry date: 10/03/2019
Qinghai Province, 455004
See notesB.O.S. / Con CastSteelmakingXINYU IRON & STEEL CO. LTD. WuhanSee notesE.A.F. / Con Castcarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesFH27S, FH32, FH36, FH40 50Higher StrengthAH27S, AH40, DH27S, DH40, EH27S, EH40 60AH32, AH36, DH32, DH36, EH32, EH36 80360AR, 410AR 20Boiler & Pressure Vessel360, 410 60360FG, 410FG, 460FG, 490FG, 510FG 80A, B 14Normal StrengthSectionsAH27S, AH32, AH36 14Higher Strength
Xinyu CityJiangxi Province 338001
1 Yejin Road
Tel: 0791 6293506Email: XR@xinsteel.com.cnWeb: www.xinsteel.com.cnAll grades with specified through thickness properties, designation to Z35 may be addedCertificate #: MD00/3093/0009/1 Expiry date: 10/06/2019
As at 10 April 2018 25Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Alloy 24EAF/LRF/VD/IngotSteelmakingXINYU XINLIANG SPECIAL STEEL CO., LTD. WuhanCarbon, Carbon-manganese 34alloy 24Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 34
Liangshan TownXinyu, 338013
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050 email: Certificate #: MD00/4596/0001/1 Expiry date: 12/07/2019
Approved for Z25 & Z35 grades.
Jiangxi
As belowB.O.S./Ingot/Con CastSteelmakingXISC - HUNAN VALIN XIANGTAN Wuhancarbon, carbon-manganese, alloy 300SlabsSemi-FinishedA, B, D, E 150Normal StrengthPlatesFH40 40Higher StrengthAH42, AH46, AH50, AH55, AH62, AH69, DH42,DH46, DH50, DH55, DH62, DH69, EH42, EH46,EH50, EH55, EH62, EH69*
50
FH27S, FH32, FH36 60AH40, DH40, EH40, EH47 80AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36, LTFH40
40Ferritic Low Temperature
Xiangtan City,Hunan Province,
IRON & STEEL CO., LTD.Yuetang District,
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050 email mailto:hnxgjiazg@sohu.com web http://www.hnxg.com.cn
Certificate #: MD00/3258/0012/1 Expiry date: 07/08/2018
Approved for Z25 & Z35 grades.
* Mximum approved welding heat input in fabrication is 3.0 kJ/mm.
As belowE.A.F./V.O.D./Con CastSteelmakingYANTAI WALSIN STAINLESS STEEL CO., LTD. Qingdaoaustenitic stainless steel, duplex stainless steel,alloy steel
260Blooms/BilletsSemi-Finished
No. 2 Wuzhishan Road,Economic Technical Development Zone
Tel: +86 535 2166688 Fax: +86 535 2165008 Email:Lisa_zhao@walsin.comCertificate #: MD00/3992/0002/1 Expiry date: 20/02/2018
Yantai City, shandong Province
austenitic stainless, duplex stainlessE.A.F. / IngotSteelmakingYONGXING SPECIAL STAINLESS STEEL CO LTD Shanghai Portaustenitic stainless, duplex stainless 11Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 500Bars
Yangjiabu,Huzhou City,
Tel No. +86 572 2350629 Fax No: +86 572 2351517Email: wang _jianyong@163.comWeb : www.yongxingbxg.cnCertificate No. MD00/3791/0003/1 Expiry date 05/06/2019
Zhejiang Province
As belowE.A.F. / Con CastSteelmakingZENITH STEEL GROUP CO., LTD. JiangyinU2, U3 130Chain Cable StockBars
No. 1 Zhongwu AvenueChangzhou City
Tel No. +86 519 88771301 Fax No: +86 519 88771301Email: ludengyao@126.comCertificate No. MD00/4273/0003/1 Expiry date 21/12/2019
Jiangsu Province
As belowE.A.F./V.O.D./IngotSteelmakingZHANGJIAGANG GUANGDA SPECIAL MATERIALCo., LTD
Jiangyin
carbon, carbon-manganese, alloy 10Ingots (tonnes)Semi-Finished
As at 10 April 2018 26Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Fenghuang Town,Zhangjiagang City, Jiangsu Province.
Anqing Village,
Tel: 00-86- 512- 5890270 Fax. No. 00- 86 - 512 - 58456318
E-mail: 79880522@qq.com
Website: gdjxdz.net
Certificate No: MD00/4690/0003/1 Expiry Date: 18.06.2020
As belowE.A.F./A.O.D./Con CastSteelmakingZHANGJIAGANG POHANG STAINLESS STEEL CO.,LTD.
Shanghai Port
As below 220SlabsSemi-Finished
304L, 316L, 321 80Austenitic StainlessPlates
304L, 316L, 321 16Austenitic StainlessHot Rolled Coil
UNS S31803 10Duplex Stainless
Daxin Riverside Road,Zhangjiagang City,
Plant No. 2
Tel: +86 512 58569312 Fax: +86 512 58569768-8023email: shanjg@zpss.com web: www.zpss.comCertificate No: MD00/4734/0001/1 Expiry Date: 13/11/2020
Jiangsu Province,
As belowE.A.F./V.O.D./IngotSteelmakingZHEJIANG DALONG ALLOY STEEL CO., LTD. Shanghai PortCarbon, Carbon-manganese, Alloy 31EAF/LRF/VD/Ingotaustenitic stainless, martensitic stainless, duplexstainless
23Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy 31
Jiashan,Jiaxing,
Fenhu Industry Zone,Taozhuang Town,
Tel: +86 573 84899666 Fax: +86 573 84895280email: zj-dalong@163.com web: www.zj-dalong.com
Zhejiang Province
austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingZHEJIANG TSINGSHAN IRON & STEEL CO.LTD. Zhoushanaustenitic stainless 3Ingots (tonnes)Semi-Finishedaustenitic stainless steel 240Blooms/Billetsaustenitic stainless 150Billets
Wenxi Town,Qingtian,
Xiaoshi Industry Zone
Tel No. 0086 578 6071301 Fax No. 0086 578 6062336
Email 1030009089@qq.com
Web : www. zjqingshan.cn
Cert no. MD00/3673/0003/1 Expiry date: 24/08/2018
As belowA.O.D./Con CastSteelmakingZHENSHI GROUP EASTERN SPECIAL STEEL CO.,LTD.
Shanghai Port
304L, 304LN, 316L, 316LN, 317L, 317LN, 321 40Austenitic Stainless SteelPlates from coils
UNS S31803 40Duplex Stainless
304L, 316L, 317L, 321, 304LN, 316LN 16Austenitic StainlessCoil
UNS S31803 12Duplex Stainless
Xinfeng TownNanhu District, Jiaxing
Economic Development park (North)
Tel: +86 573 8398 8183 Fax: +86 573 8391 6907 Email to: lijie@zsess.com
Certificate #: MD00/4426/0003/1 Expiry date: 29/01/2021
Zhenjiang Province 314005
As belowB.O.S. / Con CastSteelmakingZHONGPU (HANDAN) IRON AND STEEL CO.,LTD.
Dalian
carbon, carbon-manganese 320SlabsSemi-Finished
A, B, D 38Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength
As at 10 April 2018 27Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
China, People's Republic of360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure VesselPlatesZHONGPU (HANDAN) IRON AND STEEL CO.,
LTD.Dalian
Yangyi Town,Wuan City,
No.1 & No.2 Steel Making Plant
Tel: +86 (0)310-5178955 Fax: +86 (0)310-5178928 email: zprzb2008@163.com web: www.hbpygt.com
Certificate #: MD00/4034/0002/1 Expiry date: 26/04/2018
Hebei Province, 056305
carbon, carbon-manganese, alloy, stainless steel 6Ingots (tonnes)Semi-FinishedZHONGXING ENERGY EQUIPMENT CO., LTD NantongAs above 350Blooms/Billetscarbon, carbon-manganese, alloy 6EAF/LRF/VD/IngotSteel-makingaustenitic stainless 6IF/AOD/Ingot
SanchangHaimen City
No. 899, Zhonghua East Road
Tel: +86 513 82608033 Contact: Mr Liu Zi Ping Email to: nttgsyh@163.com Web http://www.zxnyzb.com
Certificate #: MD00/4505/0002/1 Expiry date: 29/07/2018
Jiangsu Province
Croatia
As belowE.A.F. / Con CastSteelmakingABS SISAK d.o.o. Zagrebcarbon, carbon-manganese 410BilletsSemi-Finished
BRA�E KAVURI�A 12,44010 Sisak,Tel: +385 44 565467 email: t.marjanovic@absacciai.it
Cert No. MD00/4210/0001/1 Expiry date: 25/07/2016
Czech Republic
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL OSTRAVA a.s. Praguecarbon, carbon-manganese, alloy 150SlabsSemi-Finishedcarbon, carbon-manganese, alloy 400BilletsA, B, D 14Normal StrengthSectionsA, B, D 60Normal StrengthBars
Vratimovská 689707 02 Ostrava-Kuncice
Approval for semi finished products covers con cast slabs to 150 x (750 to 1530) mm, con cast billets to 180 x 180mm and con cast rounds to 400mm diameter.
Tel: +420 595 684 213 email: shahab.husain@arcelormittal.com web: www.arcelormittal.com/ostrava
Certificate #: MD00/1123/0010/1 Expiry date: 10/12/2019
carbon, carbon-manganese 5Structural SectionsFabricated SectionsARCELORMITTAL TUBULAR PRODUCTS KARVINAA.S.
Prague
733 23 KarvinaRude armady 471
Tel: +420 596 391 465
E-mail: daniel.stolarz@arcelormittal.com
Website: www.jakl.cz
Longitudinal high frequency induction (HFI) welded tubes, pipes and hollowsCertificate #: MD00/4299/0002/1 Expiry date: 24/03/2020
As belowE.A.F. / IngotSteelmakingPILSEN STEEL s.r.o. Praguecarbon, carbon-manganese, alloy 200Ingots (tonnes)Semi-Finished
As at 10 April 2018 28Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
316 00 PlzenTylova 1/57
Tel: +420 378 134 225 Mob: +420 603 587 246email: karel.rau@pilsensteel.cz web: www.pilsensteel.cz Certificate # MD00/1383/0006/1 Expiry date: 23/03/2017
As belowB.O.S./Ingot/Con CastSteelmakingTRINECKE ZELEZARNY, a.s. PragueAs belowE.A.F./Ingot/Con Castcarbon, carbon-manganese 140SlabsSemi-Finishedcarbon, carbon-manganese, alloy 525BarsA 50Normal StrengthSectionscarbon, carbon-manganese, alloy 90MachineryBarsU1, U2 72Chain Cable Stock
Prumyslova 1000Stare Mesto
Tel: +420 558 534 016 Fax: +420 558 536 060 Email: mailto:radim.raska@trz.cz Web hppt://www.trz.czCertificate #: MD00/1562/0008/1 Inspection Due: 12/07/2019
739 61 Trinec
carbon, carbon-manganese, alloy 300StructuralBarsTRINECKE ZELEZARNY, a.s. Praguecarbon, carbon-manganese, alloy 300Machinery
vyrobni zavod:VZ - Sochorova valcovna
Prumyslova 1000, Stare Mesto739 61 Trinec
Tel No +420 558 536 065 Fax No. +420 558 534 926Email vit.prochazka@trz.czWeb www.trz.czMachinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.Certificate #: MD00/2955/0007/1 Expiry date: 20/02/2018
272 01 Kladno Drin
B, D 40Normal StrengthSectionsTRINECKE ZELEZARNY, a.s. PragueA 50DH32, DH36 40Higher StrengthAH27S, AH32, AH36 50
VH - Univerzalni trat Bohumin,Bezrucova 300,
Tel: +42 (0) 558 534 016 or +42(0) 602 780 683 email: martin.snapka@moravia-steel.cz web: www.trz.czThe approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.
Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, 739 70 Trinec-Stare Metso.Certificate ID No : MD00/2020.Certificate No. MD00/3056/0006/1 Expiry date: 11/02/2019
735 93 Bohumin
As belowE.A.F. / IngotSteelmakingVITKOVICE HEAVY MACHINERY a.s. Praguecarbon, carbon-manganese, alloy 130Ingots (tonnes)Semi-Finished
Ruska 2887/10170300 Ostrava-VitkoviceTel: +420 595 953 153 Mob: +420 602 535 608 email: jiri.broz@vitkovice.cz web: www.vitkovice.cz
Certificate #: MD00/2020/0007/1 Expiry date: 30/03/2020
A, B, D, E 100Normal StrengthPlatesVITKOVICE STEEL, a.s. PragueAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselA, B, D, E 16Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
16Higher Strength
A, B, D, E 50Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength
709 00 Ostrava-Hulvaky,Czech Republic
Stramberska 2871/47,
Tel: +420 602 511 031 email: otakar.blahoz@vitkovicesteel.com web: www.vitkovicesteel.com
Certificate #: MD00/4380/0002/1 Expiry date: 05/08/2019
carbon, carbon-manganese, alloy 4E.A.F. / IngotSteelmakingValcovny trub Chomutov, a.s. Prague
Rokycanska 204,CZ-338 42 Hradek u Rokycan,
Works Hradek
Tel: +420 474 644096 Fax: +420 474 642 288 Email: stehlik.libor@steel-holding.czWeb: www.steel-holding.czCertificate #: MD00/4063/0003/1 Expiry date: 04/08/2018
As at 10 April 2018 29Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingZDAS a.s. - Metallurgy Division Praguecarbon, carbon-manganese, alloy 12Ingots (tonnes)Semi-Finished
Strojirenska 675/659101 Zdar nad Sazavou
Metallurgical Plant
Tel: +420 566 643 054 Mobile: +42 602 795 859 Email: radek.paral@zdas.czWeb:http://www.zdas.czCertificate #: MD00/1697/0006/1 Expiry date: 24/08/2020
Denmark
E 60Normal StrengthPlatesNLMK DANSTEEL A/S CopenhagenA, B, D 100AH40, DH40, EH27S, EH40, FH27S, FH32, FH36 60Higher StrengthEH32, EH36, EH36S 80AH27S, AH32, AH36, DH27S, DH32, DH36 100360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
DK-3300 FrederiksværkHavnevej 33
Tel: +45 477 82647 Fax: +45 477 70302
E-mail: E.Sarkits@dansteel.dk
Web:http://www.dansteel.dk
All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.
Certificate Number: MD00/0403/0009/1 Expiry: 07/01/2018
Egypt, Arab Republic of
A, B, D 100Normal StrengthPlatesABU ZAABAL ENGINEERING INDUSTRIES CairoAH27S 20Higher Strength
Inchas
Hot and Cold Rolling mill (AZE)Abu Zaabal
Tel: +20 24469 1224 Fax: +20 24469 2608 Email: aze100@soficom.com.egWeb www.azr.comCertificate # MD00/3421/0005/1 Expiry date: 25/01/2020
As belowB.O.S. / Con CastSteelmakingEGYPTIAN IRON & STEEL CO. Port SaidA 50Normal StrengthPlatesA 8Normal StrengthHot Rolled Coil360FG, 410FG 8Boiler & Pressure VesselA 50Normal StrengthSections
HelwanCairo
El Tebbin
Tel: +202 5940593 Fax +202 5011608 quality.lap.research@hadisolb.com web www.hadisolb.com
Certificate #: MD00/0438/0009/1 Expiry date: 20/02/2019
As at 10 April 2018 30Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Finland
As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS OY Helsinki/Helsingfors
austenitic stainless 187SlabsSemi-Finished
304L, 316L, 321 12Austenitic StainlessPlates
304L, 316L, 321 12Austenitic StainlessHot Rolled Coil
304L, 316L, 321 6Austenitic StainlessCoil
Terastie 1,95490
Tel No: +358 40 7675371 Fax no:+358 16 452 350Email:susanna.siukonen@outokumpu.com Web: http://www.outokumpu.comCertificate #: MD00/1165/0008/1 Expiry date: 29/03/2020
Tornio
As belowE.A.F. / Con CastSteelmakingOVAKO IMATRA OY AB Helsinki/Helsingfors
carbon, carbon-manganese, alloy 370BloomsSemi-Finished
Carbon, Carbon manganese, Alloy 180Rolled Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
180Higher StrengthBars
carbon, carbon-manganese, alloy 180Structural
alloy 180Machinery
carbon, carbon-manganese 200
Terästehtaantie 1FI-55100 IMATRATel: +358 5 680 21 Fax: +358 5 680 2211 Email: ville.ruotsalainen@ovako.com Web:http://www.ovako.comSemi-finished products in carbon, carbon-manganese and alloy steel with fine grain (element combinations as stated), blooms to 370 mm section, to 6000mm longfor further processing to rolled productsMQS Approved - Approval No. MQS 020Certificate #: MD00/0751/0010/1 Expiry date: 05/01/2018
As belowB.O.S. / Con CastSteelmakingSSAB EUROPE OY Helsinki/Helsingfors
A, B, D, E 150Normal StrengthPlates
FH27S, FH32, FH36 40Higher Strength
AH40, DH40, DH42, EH40, EH42 80
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360AR, 410AR 40Boiler & Pressure Vessel
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG
100
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
40Ferritic Low Temperature
A, B, D, E 15Normal StrengthHot Rolled Coil
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
15Higher Strength
A, B, D, E 15Normal StrengthPlates from coils
AH27S, DH27S, AH32, DH32, AH36, DH36,EH27S, EH32, EH36
15Higher Strength
Rautaruukintie 155, PO Box 9392101 Raahe
Raahe Steel Works
Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email: lassi.myllykoski@ruukki.com Web: http://www.ruukki.com Specified through thickness properties for up to 150 mm thickness.
MQS Approved - Approval No. MQS 007Certificate #: MD00/1233/0012/1 Expiry date: 09/12/2019
As at 10 April 2018 31Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
France
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingAKERS FRANCE Lyoncarbon, carbon-manganese, alloy 70Ingots (tonnes)Semi-Finished
B.P. 1020057104 Thionville Cedex
USINE DE THIONVILLEChemin du Leidt
Tel: +33 6 79 27 94 41 e mail: mailto:christophe.evrard@akersrolls.com web: http://www.akersrolls.comCertificate #: MD00/3386/0003/1 Expiry date: 26/05/2017
304L, 316L, 304* 6Austenitic StainlessPlatesAPERAM Lyon304L, 316L, 304* 6Austenitic StainlessCoil
4 place des Forges71130 Gueugnon
Gueugnon Plant BP 1
Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Mob: +33 609320872Email: gerard.ramoissenet@aperam.com Web: http://www.aperam.comCertificate #: MD00/1582/0007/1 Expiry Date: 08/03/2020
As belowE.A.F. / IngotSteelmakingAPERAM ALLOYS IMPHY LyonFe-36Ni* 8Fe-Ni alloysPlatesFe-36Ni* 1Fe-Ni alloysHot Rolled Coil
Avenue Jean Jaurès58160 IMPHYTel: +33 3 86 21 34 96 Email:mailto:marie-paul.solignac@aperam.com Web:http://www.aperam.com*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) accepted for approved applications; material greater than 1.5mm supplied in the AsRolled condition; materials 1.5mm or less are supplied in the solution annealed condition.Certificate Number: MD00/1870/0007/1 Expiry: 1/06/2018
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL MarseilleNormal strength, Higher Strength 229SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH36 13Higher Strength460FG, 490FG, 510FG 13Boiler & Pressure Vessel360AR, 410AR 16
13776 Fos-Sur-MerCEDEX
Méditerranée Fos-sur-Mer
Tel: +33 (0) 442 47 30 68 Fax +33 (0) 4 4247 32 31Email: mailto: christophe.issartel@arcelormittal.comWeb: www.arcelormediterranee.comCertificate #: MD00/3803/003/1 Expiry date: 24/11/2018
As belowE.A.F./Ingot/Con CastSteelmakingASCO INDUSTRIES S.A.S Dunkerquecarbon, carbon-manganese, alloy 400Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 310StructuralBarscarbon, carbon-manganese, alloy 310MachineryU3 105Chain Cable StockU1, U2 130
59941 DunkerqueCedex 2
Usine de DunesBP 41
Machinery grades up to 180 mm by continuous casting, 310 mm by ingotTel +33 32829 6052 Email to: corinne.lebihan@ascometal.comCertificate #: MD00/0117/0008/1 Expiry date: 11/09/2018
As belowE.A.F. / IngotSteelmakingASCO INDUSTRIES S.A.S Marseillecarbon, carbon-manganese, alloy 400BloomsSemi-Finishedcarbon, carbon-manganese, alloy 205Billetscarbon, carbon-manganese, alloy 325StructuralBars
13771 Fos-sur-Mer
Usine de Fos-sur-MerBP 30
Tel: +33 (0) 442 479251 Fax: +33 (0) 442 479276
Email : etienn.archaud@ascometal.com
Website: ascometal.com
Certificate Number: MD00/0118/0007/1 Expiry: 02/09/2018
As BelowEAF/LMF/Con CastSteelmakingASCOVAL LyonCarbon, Carbon-manganese, Alloy 325As Cast Round SectionSemi-Finished
As at 10 April 2018 32Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Zone Industrielle N°4,CS30072,
Rue du Galibot
Tel: +33 03272 31890 Mob: +33 (6)801 24259email: helene.deporter@ascometal.com
Certificate No: MD00/4738/0001/1 Expiry Date: 19/12/2020
59880 Saint-Saulve
As belowE.A.F. / IngotSteelmakingAUBERT & DUVAL Lyoncarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
42Ingots (tonnes)Semi-Finished
BP 14142704 FIRMINY CEDEX
Firminy Plant
Tel: +33 4 77 40 37 41 Email mailto: christrophe.mercier@eramet-aubertduval.com Web: http://www.aubertduval.com
Ingots as semi-finished products to the above maximum weight; nominal; 1550/1730mm diameter x 2200mm; are approved for further processing for forgings.
Certificate Number: MD00/1770/0003/1 Expiry: 25/09/2018
As aboveE.A.F. / IngotSteelmakingAUBERT & DUVAL Lyonalloy, austenitic stainless steel, carbon, carbonmanganese
450Blooms/BilletsSemi-Finished
carbon, carbon-manganese, alloy, austeniticstainless
50StructuralBars
carbon, carbon-manganese, alloy, austeniticstainless
200Machinery
BP 163770 Les Ancizes
Aciéries des Ancizes
Tel: +33 4 73 67 31 27email: marc.graglia@eramet-aubertduval.com www.aubertduval.comCertificate No: MD00/4537/0001/1 Expiry Date: 21/12/2018
As belowB.O.S. / Con CastSteelmakingCELSA FRANCE BilbaoNormal Strength, Higher Strength 160BilletsSemi-Finished
Rond-Point Claudius Magnin64340 BoucauTel: +33 05 59 64 41 00 Fax: +33 05 59 64 41 21 email: dgonzalezt@gcelsa.com web: hwww.celsafrance.com
Certificate Number: MD00/3539/0003/1 Expiry date: 10/11/2017
Billets as semi-finished products, nominal 160mm width and nominal 13300mm length to the above maximum thickness are approved for further processing forrolled products.
E 80Normal StrengthPlatesDILLINGER FRANCE DunkerqueA, B, D 100AH40, DH40, EH40, FH40 42Higher StrengthFH27S, FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
Port 30323032 Rue du Comte Jean - CS 56317
Tel: +33 (0)3 28 29 39 22 Fax: +33 (0)3 28 29 69 12 Email: sylvie.brachet@fr.dillinger.biz Web: http://www.dillinger-france.comSpecified through thickness properties for all normal and higher strength grade plates notation - Z35 may be added.Certificate #: MD00/1818/0011/1 Expiry date: 07/06/2019
F-59379 Dunkerque Cedex 1
carbon, carbon-manganeseE.A.F. / IngotSteelmakingINDUSTEEL FRANCE LyonA 400Normal StrengthPlatesFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 400360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni
50Ferritic Low Temperature
As at 10 April 2018 33Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
BP 368 - Chateauneuf42803 RIVE DE GIER
ARCELOR MITTALSite de Chateauneuf
Tel: +33 477 752131 Fax: +33 4 77 75 20 03 Email: Laurent.genin@arcelormittal.com
Including plates with specified through thickness properties.Certificate #: MD00/0351/0008/1 Expiry date: 18/04/2020
As belowE.A.F. / IngotSteelmakingINDUSTEEL FRANCE, site du Creusot Lyoncarbon, carbon-manganese, alloy, austeniticstainless
40Ingots (tonnes)Semi-Finished
71201 71201 LE CRUUSOT CEDEXLe Creusot Cedex
Porte du Breuil - BP 34
Tel No 33 3 8580 5575 Fax No. 33 3 8580 5211Email: charlene.janaudy@arcelormittal.comWeb: www.industeel.infoCertificate number MD00/3227/0004/1 Expiry Date: 02/03/2018Ingots also in martensitic stainless steel up to 40 T for approved applications
A, B, D, E 150Normal StrengthPlatesINDUSTEEL FRANCE, site du Creusot LyonFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 150360, 410, 360FG, 410FG, 460FG, 490FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, 1.5Ni, 3.5Ni, 5Ni, 9Ni
50Ferritic Low Temperature
304L, 316L 50Austenitic Stainless
7120156 rue Clemenceau - BP19
Tel: +33 3 8580 5575 Fax: +33 3 8580 5211Email: mailto: charlene.janaudy@arcelormittal.com Web: http://www.industeel.infoPlates with specified through thickness properties.Certificate #: MD00/1822/0008/1 Expiry date: 26/02/2018
As belowB.O.S. / Con CastSteelmakingLAMINES MARCHANDS EUROPEENS Lyoncarbon, carbon-manganese 200BilletsSemi-FinishedA 13Normal StrengthSectionsA 30Normal StrengthBars
2, Rue Emile Zola59125 Trith St LégerTel +33 (0)3 2714 2270 Fax +33 (0)3 2714 2010 Email: mailto:e.cotton@lme.frCertificate #: MD00/1395/0007/1 Expiry date: 19/10/2016
A, B, D, E 16Normal StrengthFabricated SectionsLORRAINE TUBES LyonAH32, AH36, DH32, DH36, EH32, EH36 14Higher Strength
54720 Lexy100, rue du Maréchal Foch
Tel No: +33 382 252 252 Fax No: +33 382 252 116Email: dmartini@lorraine.condesa.comWeb: www.condesa.comCertificate No: MD00/4281/0001/ 1 Expiry Date: 17/01/2017
A, B, D, E 16Normal StrengthFabricated SectionsLORRAINE TUBES LyonAH32, AH36, DH32, DH36, EH32, EH36 16Higher Strength
57480 RettelRoute du Contez
Tel No: +33 382 252 225 Fax no: +33 382 252 116Email: dmartini@lorraine.condesa.comWeb: www.condesa.com Certificate No: MD00/4282/0001/1 Expiry Date 17/01/2017
As belowE.A.F./A.O.D./Con CastSteelmakingUGITECH S.A. LyonAs below 205BilletsSemi-Finished304L, 316L, 321 32Austenitic StainlessSectionsUNS S31803 32Duplex Stainless304L, 316L, 321 130Austenitic StainlessBarsUNS S31803 130Duplex Stainlessaustenitic stainless, duplex stainless, martensiticstainless*
95Machinery
Avenue Paul Girod,73403 UGINE CedexTel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74 email: laurent.prost@ugitech.com web: www.ugitech.com
Certificate #: MD00/1583/0007/1 Expiry Date: 23/08/2017
As at 10 April 2018 34Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Germany
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BREMEN GmbH BremerhavenAs below 220SlabsSemi-FinishedA, B, D 20Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 20Boiler & Pressure Vessel
Carl-Benz- Straße 30D-28237 BremenTel +49 (0)421 648 1747 Fax +49 (0)412 648 49 3258 email: salesflat.germany@arcelormittal.com web: www.arcelormittal.com/bremen
Certificate No. MD00/0857/0007/1 Expiry date: 16/10/2019
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL HOCHFELD GmbH Hamburgcarbon, carbon-manganese, alloy 385BloomsSemi-Finishedcarbon, carbon-manganese, alloy 130Billets
Vohwinkelstraße 107D-47137 DuisburgTel 0049 (0) 203 606 66515 Fax 0049 (0) 203 606 66 362 email: c.vonlivonius@arcelormittal.com web www.arcelormittal.comCertificate Number: MD00/3631/0004/1 Expiry date: 23/07/2020
As belowB.O.S./Ingot/Con CastSteelmakingAktiengesellschaft der Dillinger Hüttenwerke HamburgA, B, D, E 170Normal StrengthPlatesFH32, FH36 50Higher StrengthAH40, DH40, EH40, EH46S, FH46S 100EH46, FH46 110AH62, AH69, DH62, DH69, EH62, EH69* 120AH36, DH36, EH36 150AH32, DH32, EH32 170AH36S, DH36S, EH36S* 220360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 5Ni
50Ferritic Low Temperature
HüttenwerkstrassePostfach 1580
All plates with specified through thickness properties.
* Approved for application with a maximum welding heat input of up to 2.3 kJ/mm.
Tel: +49 6381 474735 Fax: +49 6831 473224 email: hermann.ludwig@dillinger.biz web:: www.dillinger.biz
Certificate No. MD00/0361/0019/1 Expiry date: 18/09/2020
D-66748 Dillingen / Saar
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingBENTELER STEEL/TUBE GmbH Hamburgcarbon, carbon-manganese, alloy 215SlabsSemi-Finishedcarbon, carbon-manganese, alloy 310Blooms/Billets
Niederdarmer Straße 5D-49811 LingenTel: +49 591 80004 800 Fax: +49 591 80004 460 Email to: Luben.Savov@benteler.de Web: http://www.benteler.comCertificate No. MD00/1805/0007/1 Expiry date: 10/10/2017
Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions300mm x 230mm or 310mm round of maximum length 12,800mm
As belowE.A.F./Ingot/Con CastSteelmakingBGH EDELSTAHL FREITAL GmbH Hamburgalloy, austenitic stainless, martensitic stainless,duplex stainless
12Ingots (tonnes)Semi-Finished
As belowSlabsAs below 120Billetsalloy, austenitic stainless, duplex stainless steel,martenstic stainless*
160Semi-finished ProductsBars
alloy, austenitic stainless, duplex stainless,martensitic stainless*
165Machinery
Am Stahlwerk 1D-01705 FreitalTel: +49 (0)351 646 2408 Mob: +49 170 226 7303 email: mailto:steffen.Rehberg@bgh.de web: http://www.bgh.de
Certificate No. MD00/1973/0009/1 Expiry date: 05/08/2020
As at 10 April 2018 35Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F./V.O.D./IngotSteelmakingBGH EDELSTAHL SIEGEN GmbH Hamburgmartensitic stainless 28Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 35carbon, carbon-manganese, alloy 51
Industriestraße 9,D-57076
Tel No. +49 (0)271 701- 341 Fax No. +49 (0) 271 701376Email peter.scheer@bgh.deWeb www.bgh.deCertificate No MD00/3767/0006/1 Expiry date: 31/03/2019
Siegen
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingBUDERUS EDELSTAHL GmbH Hamburg
Martensitic stainless*E.A.F./V.O.D./Ingotcarbon, carbon-manganese, alloy 230Semi-finished ProductsBarscarbon, carbon-manganese, alloy 190Machinery
Buderusstraße 25D-35573 WetzlarTel: +49 (0)6441 374 2505 Fax: +49 (0)6441 374 2681 Email: eckard.keunecke@buderus-steel.com Web: http://www.buderus-steel.comCertificate No. MD00/0257/0012/1 Expiry date: 06/07/2020
As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE HamburgAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, austeniticstainless
80StructuralBars
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, martensitic stainless*
80Machinery
Obere KaiserstraßeD-57078 Siegen
SPECIALTY STEEL GmbH & Co. KGWorks Siegen
Tel: +49 (0)271 808 26 94 Fax: +49 (0)271 808 25 01 Email: mailto:andreas.prause@dew-stahl.com Web: http://www.dew-stahl.comCertificate No. MD00/0901/0009/1 Expiry date: 11/07/2017
As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE HamburgAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, stainless steel 66Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless
250Semi-finished ProductsBars
alloy, austenitic stainless 250Structuralalloy, austenitic stainless, duplex stainless,martensitic stainless*
250Machinery
Auestraße 4D-58452 Witten
SPECIALTY STEEL GmbH & Co. KGWorks Witten
Tel: +49 (0) 2302 292 437 Fax: +49 (0) 2302 294 008email: stephanie.pueckel@dew-stahl.com web:www.dew-stahl.comCertificate No. MD00/2075/0013/1 Expiry date: 19/01/2019
As belowE.A.F./Ingot/Con CastSteelmakingGEORGSMARIENHÜTTE GmbH Hamburgcarbon, carbon-manganese, alloy 44Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 240BloomsA, B, D, E 180Normal StrengthBarsAH32, AH36, DH32, DH36, EH32 180Higher Strengthalloy 270Structuralcarbon, carbon-manganese 280U1, U2, U3, R3 155Chain Cable Stock
D-49124 GeorgsmarienhütteNeue Hüttenstraße 1
Tel: +49 5401 394657 Fax: +49 (0)5401 39 4598 Email: uwe.huelsmann@gmh.de Web: http://www.gmh.deCertificate No. MD00/0596/0008/1 Expiry date: 01/10/2019
As belowE.A.F. / Con CastSteelmakingH.E.S. HENNIGSDORFER ELEKTROSTAHLWERKEGmbH
Hamburg
carbon, carbon-manganese, alloy 100StructuralBars
carbon, carbon-manganese, alloy 50Machinery
U1, U2 73Chain Cable Stock
Wolfgang-Küntscher-Straße 18D-16761 HennigsdorfTel: +49 (0)3302 806-728 Fax: +49 (0)3302 806-724email: ingo.laudahn@rivagroup.com web: www.rivagroup.com
Certificate No. MD00/0665/0009/1 Expiry date: 29/06/2020
As at 10 April 2018 36Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 50Normal StrengthSectionsHOESCH SCHWERTER PROFILE GmbH Hamburg
Eisenindustriestraße 1D-58239 SchwerteTel: +49 (0)2304 106-340 Fax: +49 (0)2304 106-590 Email: info@tks-hho.thyssenkrupp.com Web: http://www.hoesch-profile.deCertificate No. MD00/0682/0007/1 Expiry date: 07/01/2018
carbon, carbon-manganese, alloy, High-nickelsteel (for low temperature service)
B.O.S. / Con CastSteelmakingHüttenwerke Krupp Mannesmann GmbH Hamburg
carbon, carbon-manganese, alloy, high-nickelsteel (for low temperature service)
260SlabsSemi-Finished
carbon, carbon-manganese, alloy 406Blooms/Billets
Ehinger Strasse 200D-47259 Duisburg-Huckingen
Huckingen Works
Tel: +49 (0)203 999 2633 Fax: +49 (0)203 999 4430
email: ismael.carneiroi@hkm.de web: www.hkm.de
Certificate No. MD00/0730/0009/1 Expiry Date: 05/02/2021
B, D, E 85Normal StrengthPlatesILSENBURGER GROBBLECH GmbH HamburgA 150AH40, DH40, EH40, FH40 100Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
120
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG
100
LTAH40, LTDH40, LTEH40, 1.5Ni, 3.5Ni, 5Ni,9Ni
50Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
120
316L 80Austenitic Stainless
Veckenstedter WegD-38871 IlsenburgAll plates with specified through thickness properties.
Tel: +49 39452/85 9904 Fax: +49 39452/85 5733
E-mail: Manegold@ilsenburger-Grobblech.de
Web: www.ilsenburger-Grobblech.de
Materials Qaulity Scheme Approved. Approval No: 057
Certificate No. MD00/1654/0014/1 Expiry date: 22/02/2020
As belowE.A.F. / Con CastSteelmakingLech-Stahlwerke GmbH HamburgAs below 240Blooms/BilletsSemi-FinishedA, B 100Normal StrengthBarscarbon, carbon-manganese, alloy 90Machinery
Industriestrasse 1D-86405 MeitingenTel: +49 (0) 8271/82-325 Fax: +49 (0) 8271/82-405 Email:mailto:jochen.henze@lech-stahlwerke.de Web: http://www.lech-stahlwerke.deCertificate No. MD00/0921/0007/1 Expiry date: 01/11/2018
A 12Normal StrengthSectionsMANNSTAEDT GmbH DortmundAH32, AH36, DH32, DH36 12Higher Strength
Mendener Str. 5153840 TroisdorfEmail: b.sommer@mannstaedt.de Web: www.mannstaedt.deTel: +49 2241 842328 Fax: +49 2241 3328 Mobile: +49 176 12998066
Certificate: MD00/4700/0001/1 Expiry Date: 30/08/2020
As belowE.A.F. / Con CastSteelmakingPEINER TRÄGER GMBH HamburgA, B, D, E 40Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 40Higher Strength
D-31226 PeineGerhard-Lucas-Meyer Str. 10
Tel: +49 5171 91 9543 Fax: +49 5171 91 9373 email: peiner.traeger@sz-ag.de web: www.peiner-traeger.deCertificate No. MD00/3075/0006/1 Expiry date: 13/05/2019
As at 10 April 2018 37Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 250Normal StrengthPlatesREINER BRACH GmbH & Co. KG BremerhavenAH32, AH36, DH32, DH36, EH32, EH36 120Higher StrengthAH27S, DH27S, EH27S 250460FG, 490FG, 510FG 120Boiler & Pressure Vessel360FG, 410FG 150
Wilhelm-Karmann-Straße 5D-28237 BremenTel: +49 421 985 08-140 Fax: +49 421 985 08-149 Email: frank-santuari@brach.de Web:http://www.brach.deCertificate No. MD00/2631/0007/1 Expiry date: 31/12/2017
carbon, carbon-manganese 43Ingots (tonnes)Semi-FinishedREINER BRACH GmbH & Co. KG Bremerhaven
D-28237 BremenWilhelm-Karmann-Straße 5
Tel No +49 3364 37 81 54 Fax No +49 3364 37 81 55Email: info@brach.deWeb: www.brach.deCertificate No. MD00/4032/0004/1 Expiry Date 31/12/2017
Carbon, Carbon-manganese 200EAF/LRF/VD/IngotSteelmakingSAARSCHMIEDE GmbH FREIFORMSCHMIEDE Hamburg
Bismarckstraße 57-59D-66330 VölklingenTel:+49 (0)6898 10 2215 Fax:+49(0)6898 10 5 2215 email: n.lang@saarschmiede.com web: www.saarschmiede.com
Certificate No. MD00/2017/0003/1 Expiry date: 12/05/2020
A 40Normal StrengthBarsSAARSTAHL AG HamburgU1, U2, U3 40Chain Cable Stock
D-66511 NeunkirchenWorks Neunkirchen
Tel: +49 6898 104293 Fax: +49 6898 1054293 email: daniel.muecke@saarstahl.com web: www.saarstahl.com
Certificate No. MD00/1286/0008/1 Expiry date: 08/08/2020
As belowB.O.S. / Con CastSteelmakingSAARSTAHL AG HamburgNormal Strength 265Blooms/BilletsSemi-FinishedA 160Normal StrengthBarsU1, U2, U3 100Chain Cable Stock
Bismarckstrasse 57 - 59D-66330 Völklingen
Works Völklingen
Tel: +49 (0) 6898 104 293 Fax: +49 (0) 6898 105 4293 email: daniel.muecke@saarstahl.com web:www.saarstahl.com
Certificate Number: MD00/1931/0008/1 Expiry: 08/08/2020
As belowB.O.S. / Con CastSteelmakingSALZGITTER FLACHSTAHL GmbH Hamburgcarbon, carbon-manganese 350SlabsSemi-Finished
D-38239 Salzgitter,Eisenhüttenstrasse 99,Tel: +49 5341 21-3121 Fax: +49 5341 21-2510Email: flachstahl@salzgitter-ag.comWeb: www.salzgitter-flachstahl.de
Approved slab section sizes up to 350 x 2600mm.
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades andferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The finalprocessing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanicalproperties.Certificate No. MD00/3990/0002/4 Expiry date: 14/02/2018
A, B, D, E 50Normal StrengthPlatesSALZGITTER MANNESMANN GROBBLECH GmbH HamburgAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 50Austenitic Stainless
Sandstrasse 140D-45473 Mülheim an der RuhrTel: +49 208 458 4878 Fax: +49 208 458 4511email: Schaffenberg.S@Salzgitter-AG.de web: www.smgb.de
Certificate No. MD00/1806/0008/1 Expiry date: 26/04/2020
As at 10 April 2018 38Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / IngotSteelmakingSCHMIEDEWERKE GRÖDITZ GmbH Hamburgcarbon, carbon-manganese, alloy, austeniticstainless
84Ingots (tonnes)Semi-Finished
D-01609 GröditzRiesaer Straße 1
Tel: +49 35263 62970 Fax: +49 35263 62973 email: marlen.thiemig@stahl-groeditz.de web: www.stahl-groeditz.de
Certificate No. MD00/2880/0007/1 Expiry date: 10/04/2020
Including ESR ingot and the supply of liquid steel to Stahlguss Groditz GmbH.
As belowE.A.F./V.O.D./IngotSteelmakingSILBITZ GUSS GmbH Hamburgduplex stainless 7Ingots (tonnes)Semi-Finished
Dr. - Maruschky- Straße 2D-07613 Silbitz/ThüringenTel: +49 (0)3 6693 80-250 Fax: +49 (0)3 6693 80251 email: mailto: jfriede@silbitz-guss.de web: www.silbitz-guss.de
Certificate #: MD00/1382/0003/1 Expiry date: 30/08/2020
Ingot approval covers duplex and superduplex grades.
alloy 40MachineryBarsSTAHLWERK ANNAHÜTTE MAX AICHER GMBH &CO. KG
Hamburg
D-83404 HammerauMax-Aicher-Allee 1+2
Tel: +49 (0) 8654 487 429 Fax: +49 (0) 8654 487 968Email: georg.ramstetter@annahuette.comweb: www.annahuette.comCertificate No.: MD00/4658/0001/1 Expiry date: 01/02/2020
carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingSTAHLWERK BOUS GMBH Hamburgcarbon, carbon-manganese 60Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 500Billets
D-66359 Bous/SaarP/O Box 1243
Tel: +49 6834 81 292 Fax: +49 6834 81 586 email: ldekker@stahlwerk-bous.de web www.stahlwerk-bous.deIngots up to 60 tonne and 2300 mm dia.Con cast billets approved up to 430 x 320mm section and 500mm diamater.
Certificate #: MD00/1249/0007/1 Expiry date: 19/08/2019
As belowE.A.F. / Con CastSteelmakingSTAHLWERK THÜRINGEN GMBH HamburgA, B 25Normal StrengthSectionsAH32, AH36, DH32, DH36 25Higher Strength
D-07333 UnterwellenbornKronacher Straße 6
Tel +49 3671 455006010 Fax +49 3671 45507710 Email: gerd.hoffmann@stahlwerk-thuringen.de Web http://www.stahlwerk-thueringen.deCertificate #: MD00/1424/0008/1 Expiry date: 19/11/2018
As belowE.A.F. / IngotSteelmakingSchmidt + Clemens GmbH +Co. KG Hamburgcarbon, carbon-manganese, alloy, austeniticstainless
50StructuralBars
D-51789 LindlarKaiserau 2
Tel No: +49 (0) 22 66 92 426 Fax No: +49 (0) 22 66 92 84 26email: a.hohn@schmidt-clemens.de web: www.schmidt-clemens.deCertificate #: MD00/1319/0009/1 Expiry date: 09/10/2019
A, B, D, E 20Normal StrengthHot Rolled CoilTHYSSENKRUPP STEEL EUROPE AG HamburgAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure VesselA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength410 FG, 460 FG, 360 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure Vessel
Kaiser-Wilhelm-Straße 100D-47166 Duisburg
Works Bochum
Tel: +49 (0)203 52-45582 Fax: +49 (0)203 52-43568web: www.thyssenkrupp-steel-europe.com
Certificate No. MD00/0899/0009/1 Expiry date: 22/08/2020
As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG HamburgNormal strength, Higher Strength 255SlabsSemi-FinishedA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
As at 10 April 2018 39Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeWorks BeeckerwerthTel: +49 (0)203 52-23456 Fax: +49 (0)203 52-42100Web: www.thyssenkrupp-steel-europe.com
Certificate # MD00/1823/0009/1 Expiry date: 17/08/2020
As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG HamburgA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
Works BruckhausenTel: +49 (0)203 52-25591 Fax: +49 (0)203 52-25594 web: www.thyssenkrupp-steel-europe.com
Certificate No. MD00/1824/0009/1 Expiry date: 23/08/2020
A, B, D, E 150Normal StrengthPlatesTHYSSENKRUPP STEEL EUROPE AG HamburgFH27S, FH32, FH36 50Higher StrengthAH40, DH40, EH40 60AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, 5Ni, 9Ni
50Ferritic Low Temperature
UNS S31803 35Duplex StainlessA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36,EH27S, EH32, EH36
20Higher Strength
360 FG, 460 FG, 410 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure VesselWorks Duisburg-SüdTel: +49 (0)203 52-45582 Fax: +49 (0)203 52-45568Web: www.thyssenkrupp-stahl.com
Certificate No. MD00/1825/0012/1 Expiry date: 17/08/2020
Specified through thickness properties on all normal and higher strength steel grade plates.
India
As belowA.O.D./Con CastSteelmakingAMBICA STEELS LIMITED Mumbaiaustenitic stainless, duplex Stainless 250BilletsSemi-Finished304L, 316L 125Austenitic StainlessBarsUNS S31803 125Duplex Stainless
Sahibabad-201010,Ghaziabad,
51/2, Site IV,Industrial Area,
Tel: +91 9811 045363 Fax: +91 4189366web: www.ambicasteels.com
Certificate No: MD00/4531/0001/1 Expiry Date: 01/12/2018
Approval for bars includes Bright Bars.
Approval covers IF/AOD steelmaking and concasting at the above address and also rolling and heat treatment activities at Plot No.-32, Site II, Loni RoadIndustrial Area, Mohan Nagar, Ghaziabad-201 007, Uttar Pradesh.
Uttar Pradesh
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingARCVAC FORGECAST LTD Chennaicarbon, carbon-manganese, alloy 10Ingots (tonnes)Semi-Finished
P.O: PanchgharaHooghly.
NH 2, Durgapur Expressway
Tel: + 91 33 2600 2176; Fax + 91 33 2659 8002Email: swapan@smithy.inWeb: www. arcvacsteel.comCertificate No. MD00/3561/0004/1 Expiry date: 06/02/2018
West Bengal - 712 306
As belowE.A.F. / Con CastSteelmakingBHUSHAN POWER & STEEL LIMITED Chennaicarbon, carbon-manganese 200BilletsSemi-FinishedU1, U2, U3 90Chain Cable StockBars
Vill. Thelkoli, P.O. Lapanga,Tehsil - Rengoli,
Tel: +91 663 253 5000 / 256 2026-32 Fax: +91 663 256 2007 / 256 2011 Email: Orissa@bpsl.net Web: http://www.bpsl.netBillets as semi-finished products nominal 200mm maximum width x nominal 12000mm maximum length are approved for further processing for rolled products.Bars for Grades U1 and U2 accepted for end use in the normalised condition; bars for Grade U3 accepted for end use in the quenched and tempered condition.Certificate Number: MD00/4178/0002/1 Expiry: 09/06/2019
Distt. Sambalpur - 768 232,
As at 10 April 2018 40Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
austenitic stainless steel, as below 200A.O.D./Ingot/Con CastSteelmakingCHANDAN STEEL LIMITED Mumbai
GIDC Umbergaon Dist.Valsad
Plot 31, 32, 33B, 35, 36
Admin Office: Tel: +91 22 66290600, Fax: +91 22 66290633/34 Email to: csl@chandansteel.netWorks: Tel: +91 260 3089999, Fax: +91 260 2562287/2560103 Email to: exports@chandansteel.netWebsite: www.chandansteel.net
Certificate No. MD00/4376/0001/1 Expiry date: 08/07/2017CCM Billets 100 to 200mm square of various sections cast from 4m to 9mm in lengthIngots of maximum weight 2500kg
Gujarat 396171
As belowE.A.F. / Con CastSteelmakingESSAR STEEL INDIA LTD. MumbaiNormal strength, Higher Strength 260SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360FG, 410FG 20Boiler & Pressure VesselA, B 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength
Hazira - 394270District Surat
Hot Strip Mill
Tel: +91 261 6683902/6683142 Email mailto: Rajat.Gupta@essar.com Web http://www.essar.com Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved forfurther processing for rolled products.Certificate No. MD00/2091/0009/1 Expiry date: 05/06/2018
Gujarat
E 70Normal StrengthPlatesESSAR STEEL INDIA LTD. MumbaiA, B, D 100AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
70Higher Strength
360FG, 410FG 100Boiler & Pressure VesselPlate Mill DivisionTel: +91 261 668 3902 or 6739 Fax: +91 261 668 6739email maneesh.moti@essar.com web www.essar.com
Certificate Number: MD00/3979/0005/1 Expiry: 16/01/2018
All plates are restricted to a maximum width of 4550mm.
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingISMT LIMITED (STEEL PLANT) Mumbaicarbon, carbon-manganese, alloy 225BloomsSemi-Finishedcarbon, carbon-manganese, alloy 150Bars
Jejuri 412 303Purandar, Pune
Morgaon Road
Tel: +91-020-414 34100 Fax: +91-020-26630779 Email: ln.hegde@ismt.co.in Web http://www.ismt.comCertificate number. MD00/3816/0003/1 Expiry date: 22/08/2019
Maharashtra
austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingJINDAL STAINLESS (HISAR) LIMITED Mumbaiaustenitic stainlessE.A.F./V.O.D./Con CastAs below 200SlabsSemi-Finished304L, 316L, 317L, 321, 347 53Austenitic StainlessPlates
O.P. Jindal MargHisar Haryana State
Post Box No. 6
Tel: +91 98960 95018email: hsr.alok@jslhsr.com web: www.jindalstainless.comCertificate No. MD00/3110/0005/1 Expiry date: 20/10/2019
India Pin 125 005
As BelowB.O.S./E.A.F./Con CastSteelmakingJINDAL STEEL & POWER LIMITED MumbaiA, B, D 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 80Higher Strength360AR, 410AR, 460AR, 360, 410, 460, 490, 360FG,410FG, 460FG, 490FG
80Boiler & Pressure Vessel
Post Box No.16Kharsia Road
Raigarh
Tel: +91 7762 227001 10 Fax: +91 7762 227021/22 Email to rksaini@jspl.com Certificate No. MD00/3542/0004/1 Expiry date: 31/07/2020
Raigarh 496001 Chattisgarh
As at 10 April 2018 41Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingJINDAL STEEL & POWER LIMITED MumbaiA, B, D 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 70Higher Strength460FG, 490FG, 510FG 70Boiler & Pressure Vessel360FG, 410FG 80
SH - 63, Village - NishaChendipada Road, Jindal Nagar
ORISSA
Tel: +91 9777445310 email: dinesh.tripathi@angul.jspl.com web: www.jindalsteelpower.comCertificate No. MD00/4577/0001/1 Expiry date: 17/05/2019
Angul - 759111
As belowB.O.S. / Con CastSteelmakingJSW STEEL Ltd. MumbaiNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 20Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH32, EH36 20Higher StrengthA, B, D, E 20Normal StrengthPlates from coilsAH32, DH32, AH36, DH36, EH32, EH36 20Higher Strength
Vidyanagar,Bellary,
Vijayanagar Works,
Tel: +91 22 42863005 Fax: +91 22 42863000email: hemang.oza@jsw.in web: www.jsw.in
Certificate No: MD00/4514/0001/1 Expiry Date: 04/10/2018
Karnataka,
As belowE.A.F./Ingot/Con CastSteelmakingKALYANI CARPENTER SPECIAL STEELS PRIVATELTD.
Mumbai
carbon, carbon-manganese, alloy 4Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy 320Blooms
carbon, carbon-manganese, alloy 250Bars
carbon, carbon-manganese, alloy 150StructuralBars
Pune 411 036Maharashtra
Mundhwa
Tel: +91 20 6621 5000 Fax: +91 20 2682 4483 Email: nitinbhat@kcssl.com Web: http://www.kalyanicarpenter.comApproved for ingots as semi-finished products to the above maximum weight nominal 540/700mm diameter x 1770mm long 540/700 and blooms to the abovemaximum thickness nominal 400mm wide x 10,000mm.Certificate Number: MD00/4447/0002/1 Expiry: 21/08/2018
As belowE.A.F./V.O.D./Con CastSteelmakingKALYANI STEELS Ltd. Mumbaicarbon, carbon-manganese 60BarsSemi-Finished
Ginigera, Taluk and District Koppal-KarnatakaHospet Road
Tel: +91 20 66215044 Fax: +91 20 26821124Email: Pankaj.jain@kalyanisteels.comWeb: http://www.kalyanisteels.comCertificate No.: MD00/4746/0001/1 Expiry date: 28/03/2021
As belowE.A.F. / IngotSteelmakingMAHINDRA SANYO SPECIAL STEEL PVT. LTD. Mumbaicarbon, carbon-manganese, alloy, austeniticstainless
13Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy, austeniticstainless steel
260Blooms/Billets
A 50Normal StrengthSectionsA 200Normal StrengthBars
KhopoliDist. Raigad
Khopoli WorksJagdish Nagar
Tel: +91(0)2192 260500 Fax: +91 (0)2192 262496 Mobile: +91 830882 8540 Email: dande.prashantr@mahindra.comWeb www.muscoindia.comCertificate No. MD00/0971/0009/1 Expiry date: 15/07/2018
Maharashtra 410 216
UNS S31803 120Duplex StainlessBarsPRECISION METALS Mumbai
As at 10 April 2018 42Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Atkargaon, Khopoli-410203,Taluka-Khalapur, Dist- Raigad,
Plot No. 253Takai-Adoshi Road,
Tel: +91 21 92 304800 Fax: +91 21 92 304915email: bbqc@venuswires.com web: www.venuswires.comCertificate No: MD00/4590/0001/1 Expiry Date: 04/07/2019
Approved for bright round bars to above maximum diameter.Scope of approval does not include steelamaking or rolling operations.
Maharashtra,
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. MumbaiNormal strength, Higher Strength 250SlabsSemi-FinishedA, B, D 75Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
460FG, 490FG, 510FG 50Boiler & Pressure Vessel360AR, 410AR, 360, 410 63360FG, 410FG 75
Bhilai 490 001Chhattisgarh
Bhilai Steel Plant
Tel +91 788-2222040
E-mail: klbalasubramanian@@sail-bhilaisteel.com
Website: sail-bhalaisteel.com
Certificate No. MD00/1433/0010/1 Expiry date: 26/04/2020
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. ChennaiA, B 52Normal StrengthPlates360, 410, 360FG, 410FG 35Boiler & Pressure Vessel360AR, 410AR 40
Rourkela 769 011Orissa
Rourkela Steel Plant
Tel: +91 (0) 661 244 7424 Fax +91 (0) 661 251 0183 email: sc.prasad@sailrsp.co.in Web: http://www.sail.co.in Certificate Number: MD00/1434/0006/1 Expiry: 22/06/2016
As belowB.O.S. / Con CastSteelmakingTATA STEEL LIMITED ChennaiA 50Normal StrengthPlates360AR, 410AR 50Boiler & Pressure VesselA 12Normal StrengthHot Rolled Coil
Kolkata 700 07143 Chowringhee Road
Tel: +91 (33) 657 664 8310 Fax: +91 (33) 22887255/22881396 Email mailto: rahul.lai@itd.tatasteel.com Web http://www.tatasteel.comCertificate No. MD00/1489/0007/1 Expiry date: 14/02/2018
austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingVIRAJ PROFILES LIMITED (SMS, BAR ANDPROFILE DIVISION)
Mumbai
austenitic stainless steel 300Blooms/BilletsSemi-Finished
304L, 316L, 321 40Austenitic StainlessSections
austenitic stainless 200Semi-finished ProductsBars
GUT.No-25/1,25/2,26,27,31,33,34.VILLAGE-MAHAGAON, DIST-PALGHAR
G-2,23,76, MIDC, TARAPUR INDUSTRIAL AREA& SURVEY No 110, 111, 114/1, CD-116, 119 & 120,
Tel: +91 90444 1039 Fax: +91 2525 260159 Mob: +91 - 904 999 1347 E-mail: vijay.pillai.com
Website: www.viraj.com
Certificate Number: MD00/2935/0006/1 Expiry date: 06/12/2020
316Ti austenitic stainless steel accepted for approved applications.Billets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for furtherprocessing for forged products.
MAHARASHTRA - 401506
As at 10 April 2018 43Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Indonesia
B, D 25Normal StrengthPlatesPT. GUNAWAN DIANJAYA STEEL Tbk JakartaA 40AH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel
Tambak Sarioso,Asemrowo,
JL. Margomulyo No.29A,
Tel: +62 31 7490598 Fax: +62 31 7490581/7482109email: quality@gunawansteel.com web www.gunawansteel.comCertificate No. MD00/1882/0009/1 Expiry date: 14/12/2018
Surabaya 60184
A, B 50Normal StrengthPlatesPT. GUNUNG RAJA PAKSI JakartaAH36, AH40, DH36, DH40, EH36, EH40 50Higher Strength360AR, 410AR 40Boiler & Pressure VesselA, B 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 14Higher Strength360AR, 410AR 16Boiler & Pressure Vessel
JI. Imam Bonjol 4, Warung BongkokDesa Sukadanau, Clkarang Barat, Bekasi
Tel: +62 21 8900111 ext 3518 Fax: +62 21 8900333Email: mailto:dewi.pl@grdsteel.com Web: http://www.grdsteel.comCertificate No. MD00/2749/0004/1 Expiry date: 14/11/2016
West Java, Indonesia
As belowB.O.S. / Con CastSteelmakingPT. KRAKATAU POSCO JakartaNormal strength, Higher Strength 230SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
Kawasan Industri Krakatau,Cilegon,
Jalan Afrika No.2,
Tel: +62 (0)254 369700 Fax: +62(0)254 369799email: websupport@krakatauposco.co.id web: www.krakatauposco.co.id
Approval includes Z grade plates.
Certificate No.: MD00/4377/0003/1 Expiry Date: 24/08/2020
Banten, 42443
As belowE.A.F. / Con CastSteelmakingPT. KRAKATAU STEEL (PERSERO) TBK. JakartaNormal strength 200SlabsSemi-FinishedA 25Normal StrengthHot Rolled CoilA 25Normal StrengthPlates from coils
Jl. Industri No. 5PO. Box 14
Tel: +62 (0) 254 317274 Fax: +62 (0) 254 372608 email: handritoi.bharata@krakatausteel.com web: www.krakatausteel.com
Certificate Number: MD00/1183/0009/1 Expiry: 01/02/2018
Plates and coils in the supply condition TM+Acc Fine Grain Al+Nb are restricted to the thickness range 16.0 to 25.0mm.Slabs as semi-finished products nominal maximum width 2000mm x and nominal maximum length 12000 mm to the above maximum thickness are approved forfurther processing for rolled products.
Cilegon 42435
As at 10 April 2018 44Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Italy
As belowE.A.F./Ingot/Con CastSteelmakingA. C. P. SRL Milancarbon, carbon-manganese, alloy 135Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 120Blooms/Billets
Loc. Motta Alta 14Cividate Al Piano
Tel: +39 363 97193/4 Fax: +39 363 976666 Email: direzione-cividate@olifer.com Web http://www.olifer.comCertificate No. MD00/1807/0009/1 Expiry date: 10/03/2018
Bergamo
As belowE.A.F./Ingot/Con CastSteelmakingA.B.S. Acciaierie Bertoli Safau S.p.A. VeniceCarbon, Carbon manganese, Alloy 370Rolled BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 700As Cast Round SectionCarbon, Carbon-manganese, Alloy 420Rolled Square Barsalloy 240StructuralBarscarbon, carbon-manganese 270alloy 240Machinerycarbon, carbon-manganese 270U1, U2, U3 78Chain Cable StockR4 185
33050 Pozzuolo del Friuli (UD)Via Buttrio, 28
Tel: +39 0432 613211 E-mail: S.Scolari@absacciai.it Web: www.absacciai.itAddress for Orders: Rubiera Special Steel SpA, Via XXV Aprile, 64, 42013, Casalgrande (RE), Italy
The approval for mooring chain cable stock grade R4 bars is restricted to the supply of 185mm maximum diameter bars to Vicinay Sestao S.L. and to 166mmmaximum diameter bars to Vicinay Cadenas S.A., Deusto Factory, to the applicable Vicinay purchasing specification MPR4. The approval covers the ingot castmanufacturing route only.
Approval for normalised structural and machinery bars up to 270mm diameter is for both concast and ingot routes.
Certificate No. MD00/0019/0013/1 Expiry date: 13/06/2020
austenitic stainless, As belowE.A.F./A.O.D./Con CastSteelmakingACCIAI SPECIALI TERNI S.p.A. Veniceaustenitic stainlessE.A.F./V.O.D./Con Castaustenitic stainless 215SlabsSemi-Finished304L, 316L, 321 6Austenitic StainlessHot Rolled Coil
Viale B. Brin 218,I 05100 Terni,tel: +39 0744 4901 Fax: +39 0744 490904email: commercialeterni.ast@acciaiterni.it web: www.acciaiterni.com
cert no: MD00/4414/0001/1 expiry date: 05/01/2018
Approval covers concast slabs to 215 x 1565 mm section size.
Approval includes proprietry 470 LI greade, accepted for approved applications only.
Approval includes 316 Ti and 309S grade to above thickness, accepted for approved applications only.
Approval includes above grades as cold rolled coil in solution treated condition to 3mm thickness.
As below, carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingACCIAIERIA FONDERIA CIVIDALE S.P.A. Triestecarbon, carbon-manganese, alloy 35Ingots (tonnes)Semi-Finished
Zona Industriale33043 Cividale del Friuli
Via delle Industrie No. 40
Tel +39 432 706911 Fax +39 432 706920 email: afcspa@afcspa.com web www.cividalespa.com
Certificate No. MD00/3149/0006/1 Expiry date: 02/04/2020
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemicalcomposition and enables them to achieve the required mechanical properties
(Udine)
As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Venicecarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
10Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
220Billets
austenitic stainless, precipitation hardenedstainless*, martensitic stainless*
155MachineryBars
duplex stainless 205
As at 10 April 2018 45Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
36100 VicenzaViale Della Scienza, 25 z.i.
Tel: +39 0444 968211 Fax: +39 0444 968182 mail:quality@valbruna.it Web:http://www.acciaierie-valbruna.com* Accepted for approved applicationsApproval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and Grade1.4418 Quenched and Tempered.Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.Approval of Con cast material is for the production of Austenitic Stainless Steels only.Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness Certificate No. MD00/0041/0008/1 Expiry date: 31/05/2020
As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Veniceas belowA.O.D./Ingot/Con Castaustenitic stainless, duplex stainless,precipitation hardened stainless*, martensiticstainless*
73MachineryBars
Via A Volta 439100 Bolzano39100 Bolzano* Accepted for approved applicationsTel; +39 (0)471 924111 Fax: +39 (0)471 924355Email mailto:info@valbruna.it Web: http//www.acciaierie-valbruna.itCertificate No. MD00/2994/0005/1 Expiry date: 25/06/2018
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingACCIAIERIE VENETE S.p.A. Venicecarbon, carbon manganese, Alloy 280Blooms/BilletsSemi-FinishedCarbon, Carbon-manganese, Alloy 600As Cast Round Sectioncarbon, carbon-manganese, alloy 200Semi-finished ProductsBarscarbon, carbon-manganese, alloy 180Structuralcarbon, carbon-manganese, alloy 130Machinery
35020 Camin (Padova)
Camin WorksRiviera Francia, 9
Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666 email: commercial.dep@acciaierievenete.com web: www.acciaierievenete.com
Approval does not cover bars with a diameter of less than 65mm.
Certificate No. MD00/0042/0007/1 Expiry date: 25/03/2018
As belowE.A.F. / Con CastSteelmakingAFV ACCIAIERIE BELTRAME S.p.A VeniceNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 20Normal StrengthSectionsAH32, AH36, DH32, DH36 20Higher Strength
Viale della Scienza 81/A36100 VicenzaTel: +39 0444 967111 Fax: +39 0444 967282email: info@beltrame.it web: www.grupobeltrame.com
A, B, D 22Normal StrengthFabricated SectionsARMANDO CIMOLAI CENTRO SERVIZI Srl VeniceAH32, AH36, DH32, DH36 22Higher Strength
Via Masieres, No.3233080 San Quirino (PN)Tel: +39 (0)434 919292 Fax: +39 (0)434 919266email: accs_sanquirino@comolai.com
Certificate No. MD00/2620/0007/1 Expiry date: 29/11/2020
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingASO SIDERURGICA S.p.A. UNIPERSONALE MilanAs belowE.A.F/A.O.D/Ingotaustenitic stainless 30Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 65
25035 OspitalettoBrescia
Via Seriola no. 122
Tel: +39 (0)30 6841011-(0)30 6841165 Fax: +39 (0)30 6841012
Email: Info@aso.it Web: http://www.asogroupsteel.com.
Certificate No. MD00/0020/0008/1 Expiry date: 13/04/2020
A 20Normal StrengthFabricated SectionsBAGLIETTO S.r.l. GenoaAH36, DH36, EH36 20Higher Strength
Novi Ligure (AL)Via Castelgazzo 11
Tel: +39 0143 318000 Fax: +39 0143 319252
Website: www.baglietto.it Certificate No. MD00/3910/0003/1 Expiry date: 14.05.2020
As at 10 April 2018 46Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingCOGNE ACCIAI SPECIALI S.p.a MilanAs belowE.A.F. / Ingotaustenitic stainless, martensitic stainless, duplexstainless
14Ingots (tonnes)Semi-Finished
Martensitic Stainless Steel* 220Billetsaustenitic stainless, duplex stainless 270Martensitic Stainless Steel* 400Barsmartensitic stainless* 400StructuralBarsmartensitic stainless* 400Machinery
Via Paravera,1611100 AOSTATel No: +39 165 3021 Fax no: +39 165 302 423email: bernd.grotenburg@cogne.com web site: www.cogne.com
Steelmaking includes AOD / LF refining
* Accepted for approved applications.
Martensitic stainless bars up to 145 mm diameter produced by rolling from concast billet.Martensitic stainless bars up to 160 mm diameter produced by rolling from ingot.Martensitic stainless bars up to 400 mm diameter produced by forging from ingot.
Machinery bars from concast/rolling route approved up to 125mm.
Certificate No.MD00/3809/0003/1 Expiry date 12/07/2019
carbon, carbon-manganese, alloy, austeniticstainless, duplex
125IngotsESRFOMAS S.p.A. Milan
Via Martiri della Liberazione, 1723875 Osnago (LC)Tel No +39 3999811 Fax No +39 3958487email: sonia.proietti@fomas.it web: www.fomas.itCertificate No MD00/0475/0004/1 Expiry 08/01/2019
As belowB.O.S. / Con CastSteelmakingILVA SPA IN AMMINISTRAZIONESTRAORDINARIA
Venice
Normal strength, Higher Strength 303SlabsSemi-Finished
A, B, D, E 80Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
A 10Normal StrengthHot Rolled Coil
AH27S, AH32, AH36 10Higher Strength
Via Appia KM 64874123 Taranto
Taranto Works
Tel: +39 02 307 00 775 Fax: +39 02 307 00 285 Email: commerciale.lamiere@rivagroup.com Web: http://www.rivagroup.comSpecified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be addedCertificate No. MD00/2276/0007/1 Expiry date: 09/10/2018
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingINDUSTRIE RIUNITE ODELESI I.R.O S.p.A Milancarbon, carbon-manganese 140BilletsSemi-Finished
12-25076 - Odolo (BS)Via Brescia 12,
Tel: 0365-826089, Fax No. 0365 - 860564
E-mail: bianchettifabio@iro-spa.it
Website: www.iro-spa.it
Certificate No. MD00/4589/0001/1 Expiry Date: 03/07/2019
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingLUCCHINI RS S.p.A. Milan
Via G. Paglia N.4524065 Lovere
Tel: +39 035 963520 Fax: +39 035 963488 Email: mailto: a.carrara@lucchiniRS.it Web: http://www.lucchiniRS.itCertificate No. MD00/0949/0008/1 Expiry date: 18/03/2018
Bergamo
A, B, D, E 60Normal StrengthPlatesMETINVEST TRAMETAL S.p.A. TriesteAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure Vessel
As at 10 April 2018 47Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Via Enrico Fermi, 4433058 San Giorgio di Nogaro (UD)Tel: +39 0432 629989 Fax: +39 0432 62985
E-mail: trametal@trametal.it
Website: www.trametal.metinvestholding.com
Certificate No. MD00/2004/0009/1 Expiry date: 31/07/2020
Approved for Z grade plates with specified through thickness properties when tested in accordance with Rules requirements.
Materials Quality Scheme Approved - Approval Scheme No. 061
As belowE.A.F. / IngotSteelmakingNLMK VERONA Venicecarbon, carbon-manganese, alloy 32Ingots (tonnes)Semi-Finished
Via A, Salieri, 22,37050 Vallese di Oppeano (Verona)Tel: +39 045 699 7900 Fax: +39 045 699 7901 email: verona@eu.nlmk.com Web: http://www.eu.nlmk.com/verona/Round and Polygon ingots to nominal maximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x870mm x 2050mm.Certificate Number MD00/3985/0003/1 Expiry date: 30/01/2018
Carbon, Carbon-manganese, Alloy 40EAF/LRF/VD/IngotSteelmakingNUNKI STEEL SPA Venice
E.Fermi 33,33058 San Giorgio Di Nogaro (UD),Tel: 00 39 (0)431 623943 Fax: 00 39 (0) 431 623965Certificate No.:MD00/4087/0002/1 Expiry Date: 05/11/2018
carbon-manganese 35Structural SectionsFabricated SectionsOFFICINE ANTONIO MARINO S.R.L. Venice
90040 Isola delle Femmine (Palermo)Via delle Industrie, 13
Tel: +39 091 86 71681 Fax: +39 091 86 71686Certificate No.: MD00/4625/0001/1 Expiry Date: 26/10/2016
A, B, D, E 50Normal StrengthFabricated SectionsOFFICINE NORD EST S.r.l VeniceAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Via Ungaresca No.1233080 San Quirino (Pn)Tel: +39 (0)434 919091 Fax: +39 (0)434 918646 email: info@officinenordest.it
Certificate No. MD00/2626/0007/1 Expiry date: 06/12/2017
Approved welding process - SAWApproved weld type - Fillet weld only
A, B, D 10Normal StrengthSectionsOLIFER SRL MilanAH32, AH36, DH32, DH36 10Higher Strength
25076 Odolo (BS)Via G. Marconi 4
Tel +39 365 826088 Fax +39 365 860727 Email: mailto: mg.comelli@mail.olifer.com Web:http://www.olifer.com
Certificate No. MD00/4485/0001/1 Expiry date: 30/03/2018
A 25Normal StrengthFabricated SectionsPALESCANDOLO LAVORAZIONI SIDERURGICHESRL
Naples
AH32, AH36 25Higher Strength
DH36 30
Via Boscofangone, zone A.S.I., 80035 NolaTel. no. +39 0817340800; Fax. no.: +39 0817340454 Email: ppalesc@tin.it; web: www.palescandolo.itCertificate No. MD00/3850/0003/1 Expiry date: 29/10/2019
As belowE.A.F./Ingot/Con CastSteelmakingRUBIERA SPECIAL STEEL S.p.A. Venicecarbon, carbon-manganese, alloy, NormalStrength, Higher Strength
100Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy, NormalStrength, Highrer Strength
180Bars
As at 10 April 2018 48Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
42013 Casalgrande (RE)Via 25 Aprile, 64
Tel: +39 0522 997232 Fax: +39 0522 840040 E-mail: inf@arss.it & angelo.vassetta@srss.it
Website: www.arss.it
Address for orders: Rubiera Special Steel S.p.A. , Via Adda, 23, 2305, Nuova Olonio di Dubino, Italy.
Ingots as semi finished products nominal maximum diameter 1935mm x nominal maximum height 5250mm to the above maximum weight in normal strengthand higher strength grades are approved for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for furtherprocessing for forgings.Bars as semi finished products nominal maximum length 9500mm to the above maximum thickness in normal strength and higher strength grades are approvedfor further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further processing for forgings.Certificate Number: MD00/0038/0008/1 Expiry: 06/03/2019
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
30Higher StrengthSectionsSIDERVAL S.P.A. Milan
Via Chini Battista 6023018 Talamona (SO)Tel: +39 342 674152Email: mailto:alexis.guadarrama@siderval.it Web: http://www.siderval.itCertificate No. MD00/2857/0006/1 Expiry date: 14/01/2020
Japan
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingAICHI STEEL CORPORATION Kobecarbon, carbon-manganese, austenitic stainlessE.A.F. / Ingotcarbon, carbon-manganese, alloy 480Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 190BarsA 180Normal StrengthBars304L, 316L 180Austenitic Stainlesscarbon, carbon-manganese 190Structuralalloy, austenitic stainless 125Machinerycarbon, carbon-manganese 190U1, U2, U3 120Chain Cable Stock
Arao-machiTokai-shi
Chita Plant1, Wano-Wari
Tel: +81 52 603 9353 Fax: +81 52 603 9898 email: hayashida@he.aichi-steel.co.jp web: www.aichi-steel.co.jp
Certificate No. MD00/0076/0009/1 Expiry date: 23/09/2018
Aichi-ken, 476-8666
304L, 316L 150Austenitic StainlessBarsAICHI STEEL CORPORATION Kobe
Kariya-shiAichi-ken
Kariya Plant3-6, Toyota-cho
Tel +81 566 21 9130 Fax +81 566 23 6925 email: ymatsuoka@he.aichi-steel.co.jp web www. aichi-steel.co.jpCertificate No. MD00/0078/0007/1 Expiry date: 22/09/2018
448-0848
As belowE.A.F. / Con CastSteelmakingCHUBU STEEL PLATE CO., LTD. KobeA, B 50Normal StrengthPlates360AR, 410AR 40Boiler & Pressure Vessel
Nakagawa-kuNagoya
5-1, Kousudori
Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:aki-onozato@chubukohan.co.jp Web http://www.chubukokan.co.jpCertificate No. MD00/0309/0008/1 Expiry date: 18/04/2020
As belowE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Kobecarbon, carbon-manganese 7Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 275Bloomscarbon, carbon-manganese 148Billetscarbon, carbon-manganese 270StructuralBars
39, Motohama-machiTokai-shi
Chita Plant
Tel: +81 562 33 3106 Fax: +81 562 33 6598 email: y-hagama@ac.daido.co.jp web: www.daido.co.jp
Certificate No. MD00/0372/0007/1 Expiry date: 19/03/2020
Aichi-ken
As at 10 April 2018 49Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Yokohama
Shibukawa-shiGunma 377-0007
Shibukawa Plant500, Ishihara
Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:t-furuse@ac.daido.co.jpCertificate No. MD00/0375/0008/1 Expiry date: 25/11/2018
As belowE.A.F. / Con CastSteelmakingGODO STEEL LTD. Kobecarbon, carbon-manganese 490SlabsSemi-FinishedA 15Normal StrengthSectionsA 150Normal StrengthBarsU3 100Chain Cable StockU1, U2 150
Hyogo pref.
2946 Nakashima ShikamakuHimeji-city
Tel. +81 (0)79 234 9332 Fax +81(0)79 234 9538 Web: http://www.godo-steel.co.jpCertificate No. MD00/0606/0007/1 Expiry date: 05/08/2018
As belowE.A.F. / IngotSteelmakingHITACHI METALS, LTD. KobeA 150Normal StrengthBarsalloy, austenitic stainless 150Structural
Yasugi-shiShimane-ken
Yasugi Works2107-2, Yasugi-cho
Tel: +81 (0) 854 22 1908 Fax: +81 (0)854 23 0218 Email mailto:hitoshi.yamasaki.rh@hitachi-metals.co.jp Web http://www.hitachi-metals.co.jpCertificate No. MD00/0678/0007/1 Expiry date: 19/12/2018
As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION KobeNormal Strength, Higher Strength 300BloomsSemi-FinishedNormal Strength, Higher Strength 150BilletsB, D, E 25Normal StrengthSectionsA 32EH32, EH36 25Higher StrengthAH32, AH36, DH32, DH36 32
1280, Hosoe,Shikama-ku, Himeji-City,
Himeji Works
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:masanobu-kimura@jfe-bs.co.jp Web: http://www.jfe-bs.co.jpThe scope of approval for semi-finished products includes for; billets nominal maximum width 150mm x nominal maximum length 8600mm; blooms nominalmaximum widths 220mm x nominal maximum length 10.000mm; approved for further processing for rolled products.Certificate Number: MD00/1535/0007/1 Expiry: 26/08/2015
Hyogo-Pref. 672-8064,
As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION Yokohamacarbon, carbon-manganese 150BilletsSemi-FinishedA 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher Strength
Ibaraki Pref.314-0111
Kashima Works7 Minamihama, Kamisu-city
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201email: yuichiro-nishidate@jjfe-bs.co.jp web jfe-bs.co.jpSemi finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for furtherprocessing for rolled products.
Certificate No. MD00/1920/0007/1 Expiry date: 27/01/2020
As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION KobeAs belowB.O.S. / Ingotcarbon, carbon-manganese, alloy 30Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 310Slabscarbon, carbon-manganese, alloy 750BloomsA, B, D, E 200Normal StrengthPlatesAH42, FH27S, FH32, FH36 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69
75
AH40, DH40, EH40 80EH40S** 85EH47 90EH40S* 100AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360AR, 410AR 40Boiler & Pressure Vessel360, 410 100360FG, 410FG, 460FG, 490FG, 510FG 1349Ni 40Ferritic Low TemperatureLTAH27S, LTAH32, LTAH36, LTDH27S, 50
As at 10 April 2018 50Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
JapanLTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low TemperaturePlates
304L, 316L 50Austenitic StainlessE/304L, E/316L 30CladA, B, D, AH27S, AH32, AH36, DH27S, AH40,DH32, DH36, DH40, EH27S, EH32, EH36, EH40
50Tapered
A, B, D, AH27S, AH32, DH27S, DH32 40Differential ThicknessA, B 16Normal StrengthHot Rolled Coil360, 410 16Boiler & Pressure VesselA, B, D 32Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
32Higher Strength
carbon, carbon-manganese 400StructuralBarsalloy 165Machinerycarbon-manganese 190U1, U2 130Chain Cable Stock
Kawasaki-DoriKurashiki
West Japan Works (Kurashiki)1 Mizushima
Tel: +81 (0)86 447 2652 Fax: +81 (0)86 447 2735 email: y-kida@jfe-steel.co.jp www.jfe-steel.co.jp/works/west/
Certificate No. MD00/0838/0017/1 Expiry date: 14/10/2018
Ingot cast maximum thickness plate 200 mm.Continuous cast maximum thickness plate:Grade A Normalised: up to 200mm. Grades B and D Normalized: up to 155 mm. Other grades and conditions: up to 100mm.Specified through thickness properties on all plate grades.Thermo Mechanical = TMCPTM + Accelerated Cooling = TMCPTapered plates up to 8 mm/m taper ratio.Differential thickness plates, differential thickness 8mm by TMCP, 5mm by Normalized rolling.
MQS Approved - Approval No. MQS 022
As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION Kobecarbon, carbon-manganese, Normal strength,Higher Strength
300SlabsSemi-Finished
carbon, carbon-manganese, Normal Strength,Higher Strength
250Blooms/Billets
A, B, D, E 120Normal StrengthPlatesFH27S, FH32, FH36, FH40 80Higher StrengthEH40S* 85AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, EH47,EH40*
100
360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 55360FG, 410FG 70LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36
40Ferritic Low Temperature
304L, 304LN, 316L, 316LN, 317L, 317LN 55Austenitic StainlessA to EH36/304L, A to EH36/316L 30CladA, DH34S, B, D, A,B, AH32, AH36, DH32,DH36, AH34S
50Differential Thickness
A, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32 8Higher Strength460FG, 490FG 8Boiler & Pressure Vessel360, 410, 360FG, 410FG 12E 18Normal StrengthSectionsA, B, D 35AH40, DH40, EH40, FH27S, FH32, FH36 18Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
36
LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36
18Ferritic Low Temperature
As at 10 April 2018 51Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Fukuyama-cityHiroshima-pref.
West Japan Works (Fukuyama)1, Kokan-cho
Tel. (0)84 945 3160 Fax (0)84 945 3101 Email: k-nibu@jfe-steel.co.jp Web http://www.jfe-steel.co.jp
TM + Acc = OLAC process
For differential thickness plates, the maximum thickness differential for a thickness of 50mm is 10mm for normal strength grades and 6mm for higher strengthgrades
Approved for the supply of plates with specified through thickness properties (Z25/Z35).
MQS Approved - Approval No. MQS 005
Certificate No. MD00/1055/0015/1 Expiry date: 14/10/2018
721-8510
As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION YokohamaA, B, D, E 100Normal StrengthPlatesFH27S, FH32, FH36 42Higher StrengthAH42, DH42, EH42 83AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
90
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 460FG, 490FG, 510FG 50360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
42Ferritic Low Temperature
D, E 40Normal StrengthTapered Plates maxA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, AH40, DH40, EH40
50Higher Strength
AH32, AH36 22Higher strengthTapered Plates max
Kawasaki-kuKawasaki
East Japan Works (Keihin)1-1, Ohgishima
Tel: +81 44 322 1185 Fax: +81 44 322 1510 Email: m-toyonaga@jfe-steel.co.jpAll plate grades with specified through thickness properties.Materials Quality Scheme Approved - Approval No. MQS 034Certificate No. D00/1056/0011/1 Expiry date: 28/10/2018
210-0868
austenitic stainlessB.O.S/V.O.D./Con CastSteelmakingJFE STEEL CORPORATION Yokohamaaustenitic stainless 275SlabsSemi-Finished
Chuo-kuChiba 260-0835
East Japan Works (Chiba)1, Kawasaki-cho
Tel: +81 43 262 2287 Fax: +81 43 262 2980email: mas-oota@jfe-steel.co.jp web: www.jfe-steel.co.uk
Certificate No.: MD00/4065/0002/1 Expiry Date: 06/08/2018
As belowB.O.S. / Con CastSteelmakingKOBE STEEL, LTD. KobeAs belowB.O.S. / IngotAs belowE.A.F. / Con CastAs belowE.A.F. / IngotA, B, D, E 150Normal StrengthPlatesDH42, DH50, DH55, DH62, DH69, EH42, EH50,EH55, EH62, EH69, FH40, FH42, FH46, FH50,FH55, FH62, FH69
50Higher Strength
AH46, DH46, EH46 60AH40, DH40, EH40 80FH27S, FH32, FH36 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
90Ferritic Low Temperature
A,B, D,E, HTS up to EH36 50Differential ThicknessA, B, D 13Normal StrengthHot Rolled Coil360FG, 410FG 13Boiler & Pressure Vessel
As at 10 April 2018 52Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1 Kanazawa-choKakogawa-city
Kakogawa Works
Tel: +81 794 36 1151 Fax: +81 794 36 2079 Email: shiraishi.toshiharu@steel.kobelco.co.jpAll grades with specified through thickness properties.Certificate No. MD00/0863/0010/1 Expiry date: 14/10/2018
Materials Quality Scheme Approved - Approval No. MQS 009
Hyogo-pref.
As belowB.O.S./Ingot/Con CastSteelmakingKOBE STEEL, LTD. Kobecarbon, carbon-manganese, alloy 8Ingots (tonnes)Semi-FinishedCarbon, Carbon-Manganese, Alloy 600Rolled Bloomscarbon, carbon-manganese, alloy 250Semi-finished ProductsBarsA 250Normal Strengthcarbon, carbon-manganese, alloy 250MachineryU1, U2, U3 160Chain Cable Stock
Nada-kuKobe
Kobe Works2 Nadahama-Higashimachi
Tel +81 78 882 8057 Fax +81 78 882 8211 email: abe.masahiroi@kobelco.com web: www.kobelco.co.jp
Certificate No. MD00/0864/0009/1 Expiry date: 06/08/2020
The maximum dimensions of bars rolled from continuously cast blooms are limited to 120 mm for alloy steels and 160 mm for all other grades.
As belowE.A.F. / Con CastSteelmakingKYOEI STEEL LTD. NagasakiA 16Normal StrengthSectionsA 53Normal StrengthBars
Sanyo-Onoda CityYamaguchi Prefecture
Yamaguchi DivisionOaza Onoda 6289-18
Tel: +81 836 83 6172 Fax: +81 836 83 0839 email ssetoguchi@kyoeisteel.co.jp web www.kyoeisteel.co.jpCertificate No. MD00/1892/0007/1 Expiry date: 19/03/2019
756-0817
As belowE.A.F. / IngotSteelmakingMITSUBISHI STEEL MFG. CO., LTD. Yokohamacarbon, carbon-manganese 16Ingots (tonnes)Semi-Finished
Hirota, Kawahigashi-machiAizuwakamatsu-city
Hirota Works405, Aza Rokucho
tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619 email suzuki.toshihiro@mitubishisteel.co.jp web: www.mitsubishisteel.co.jp
Certificate Number: MD00/1802/0003/1 Expiry: 28/02/2018
Ingots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.
Fukushima Pref. 969-3471
As below 20Ingots (tonnes)Semi-FinishedMITSUBISHI STEEL MURORAN INC. YokohamaAs below 515Blooms/Billetscarbon, carbon-manganese, alloy 270StructuralBarscarbon, carbon-manganese, alloy 210Machinery
Muroran shiHokkaido
Muroran Works12, Nakamachi
Tel: +81 (0)143 41 2831 Fax: +81 (0)143 41 2869 Email: yano.masashiro@mitsubishisteel.co.jpWeb: www.mitsubishisteel.co.jpCertificate No. MD00/1893/0008/1 Expiry date: 07/04/2019
050-0087
A 38Normal StrengthBarsNIHON STEEL CO., LTD. KobeAH32, AH36 25Higher Strength
11, Rinkai-choKishiwada City
tel: +81 724 23 5151 Fax: +81 724 39 8357
Email mailto:t.naka@nihon-steel.co.jp
Certificate No. MD00/2299/0007/1 Expiry date: 09/03/2020
Osaka
As at 10 April 2018 53Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347, 304S*, 316S*
55Austenitic StainlessPlatesNIPPON STEEL & SUMIKIN Nagasaki
UNS S31803 40Duplex StainlessA/304L, D/304L, D/316L 40Clad
2108-1, Oaza Maeda Aza HatoYawata Higashi-ku
STAINLESS STEEL CORPORATIONYawata Works
* Grades 304 and 316 may be accepted for approved applications.Tel; +81 93 672 2290 Fax: +81 93 672 2251 Email: mailto:yamamoto.yoshiteru@nssc.nssmc.comweb: http://nssc.nssmc.comCertificate No. MD00/1105/0010/1 Expiry date: 22/05/2018
Kitakyshi City, Fukuoka Pref.
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingNIPPON STEEL & SUMIKIN Nagasakiaustenitic stainless, duplex stainless 235SlabsSemi-Finished304L, 316L 8Austenitic StainlessPlates304L, 316L 8Austenitic StainlessHot Rolled Coil
3434 ShimataHikari City
STAINLESS STEEL CORPORATIONProduction Division, Hikari Works
Tel +81 833 71 5029 Fax +81 833 71 5215 Email: kikunaga.taketoshi.pa2@nssc.nssmc.comCertificate No. MD00/3196/0005/1 Expiry date: 22/10/2020
Yamaguchi 743-8550
As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
As belowSlabsSemi-Finished
carbon, carbon-manganese 300
carbon, carbon-manganese, alloy 165Blooms/Billets
A, B, D, E 100Normal StrengthPlates
AH42, DH42, EH42, FH42 50Higher Strength
AH46, AH50, DH46, DH50, EH46, EH50, FH46,FH50, FH69*, EH69*
70
AH40, DH40, EH40, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
100
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
LHAH42, LTAH46, LTAH50, LTDH42, LTDH46,LTDH50, LTEH42, LTEH46, LTEH50, LTFH42,LTFH46, LTFH50
50Ferritic Low Temperature
LTAH40, LTDH40, LTEH40, LTFH40 80
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
100
A,B,D,E, HTS up to EH40 50Tapered
A,B,D,E, HTS up to EH40 50Differential Thickness
A, B, D 24Normal StrengthSections
AH27S, AH32, AH36, DH27S, DH32, DH36 19Higher Strength
A, B 12Normal StrengthPlates from coils
360, 410 12Boiler and Pressure Vessel
A, B 25Normal StrengthHot Coiled Strip
360, 410 25Boiler & Pressure Vessel
As at 10 April 2018 54Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Kimitsu-shiChiba-ken
Kimitsu Works1 Kimitsu
Materials Quality Scheme approved - MQS001
Semi Finished products include Carbon and Carbon-manganese as Fine Grain Al and Fine Grain Al+Nb slabs to 1500mm wide, to 10,400mm long (maximumweight 24T) and Carbon, Carbon-manganese and Alloy as Killed, Fine Grain Al and Fine Grain Al+Nb Blooms to 165mm diameter, to 11m long (amaximumweight 1.85T), all for further processing.
High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn andAl contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.
Materials Quality Scheme covers Steelmaking and rolled plates only with exception of EH/FH69 grade. Strip, plate cut from coil, sections and EH/FH69 gradeapproved under Materials Survey Scheme (direct survey).
* Project specific approval only. Letter ref MAT/1100/GY/10641564 refers.
Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727
E-mail: kurogi.n9q.yasuo@jp.nssmc.com Website: www.nssmc.com/works/kimitsu/
Certificate No. MD00/1100/0014/1 Expiry date: 16/06/2020
299-1141
As BelowB.O.S./E.A.F./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
carbon, carbon-manganese, alloy 190BilletsSemi-Finished
A, B 200Normal StrengthBars
AH32, AH36, DH32 200Higher Strength
U1, U2, U3, R3, R3S, R4 136Chain Cable Stock
API-2F 152
Muroran CityHokkaido
Muroran Works12, Naka-machi
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: amata.g47.takafumi@jp.nssmc.com Web: http://www.nssmc.con/works/muroranThe approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cablefittings.Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.Certificate Number: MD00/1101/0013/1 Expiry date: 30/06/2020
050-8550
As belowB.O.S./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
A, B, D, E 130Normal StrengthPlates
FH27S 40Higher Strength
AH40, DH40 50
DH42, DH46, EH40, EH42, FH32, FH36, FH40,FH42
70
EH46, EH46S, FH46, FH46S 110
FH69* 120
DH50, DH55, DH62, DH69 200
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
210
360AR, 410AR 40Boiler & Pressure Vessel
360, 410 115
360FG, 410FG, 460FG, 490FG, 510FG 120
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
40Ferritic Low Temperature
As at 10 April 2018 55Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Tokai-machiTokai-city
Nagoya Works3, 5 Chome
Tel +81 52 603 7236 Fax +81 52 603 7229 Email: okushima_6d7.motohiro@nscmc.comAll grades and thicknesses with specified through thickness properties (Z35)Certificate No. MD00/1102/0013/1 Expiry date: 15/07/2019
Aichi Pref. 476-8686
As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Nagasaki
A, B, D, E 100Normal StrengthPlates
DH42, EH42, FH42 50Higher Strength
EH40S* 60
EH47-W430, EH47-W140 70
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 80
EH47 90
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, EH40*, EH47S, EH40S**
100
360AR, 410AR, 460AR 40Boiler & Pressure Vessel
360, 410, 460, 490 90
360FG, 410FG, 460FG, 490FG, 510FG 100
LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40
80Ferritic Low Temperature
AH40, DH40, EH40 30Tapered
A, B, D, E, A,B,D,E, AH27S, AH32, AH36,DH27S, DH32, DH36, EH27S, EH32, EH36
50
A,B,D 35Differential Thickness
A,B, A,B,D,E, AH27S, AH32, AH36, DH27S,DH32, DH36, EH27S, EH32, EH36
50
A 12Normal StrengthHot Rolled Coil
AH27S, AH32, AH36 12Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel
Oita-CityOita-Prefecture
Oita Works1, Oaza Nishinotsu
Tel +81 97 553 2122 Fax +81 97 553 2379
Email: saito.bc3.shuntaroh@jp.nssmc.com
Web http://www.nssmc.com/works/oita/index.html/
All plates with specified through thickness properties.* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thicknessrange of EH40S is 30mm to 60mm.* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.** EH40S is approved with demonstrated brittle crack arrest properties.
* EH40 is approved with demonstrated brittle crack arrest properties.
Materials Quality Scheme Approved - Approval No. MQS010
Certificate No. MD00/1103/0018/1 Expiry date: 29/03/2019
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
austenitic stainlessA.O.D./Con Cast
carbon, carbon-manganese 300SlabsSemi-Finished
A, B, D, E 150Normal StrengthPlates
As at 10 April 2018 56Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Japan 150Normal StrengthPlatesCORPORATION
FH27S 32Higher Strength
FH32, FH36 43
AH42, AH46, AH50, AH55, AH62, DH42, DH46,DH50, DH55, DH62
47
AH36S, AH40S, DH36S, DH40S, EH36S, EH40S 50
EH40* 80
EH47 90
EH40S* 100
AH36, AH40, DH36, DH40, EH27S, EH32, EH36,EH40
105
AH27S, AH32, DH27S, DH32 150
360AR, 410AR, 460AR 40Boiler & Pressure Vessel
510FG 55
360, 410, 460, 490 63
360FG, 410FG, 460FG, 490FG 100
5Ni 30Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
45
9Ni 50
EH36/304L, EH36/316L 38Clad
EH27S, EH32, EH36 32Differential Thickness
A,B,D, AH27S, AH32, AH36, DH27S, DH32,DH36
35
A, B, D, E 35Normal StrengthSections
AH40, DH40, EH27S, EH32, EH36 18Higher Strength
DH27S, DH32, DH36 20
AH27S, AH32, AH36 35
A, B, D 19Normal StrengthHot Coiled Strip
360FG, 360, 410FG, 410 19Boiler & Pressure Vessel
As at 10 April 2018 57Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Kashima CityIbaraki Pref.
Kashima Works3 Hikari
Tel +81 (0)299 84 2575 Fax +81 299 84 2945
E-mail: hasegawa.md3.kazuhiko@jp.nssmc.com
Website: www.sumitomometals.co.jp
All plates with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 002
9Ni grade supplied in QLT condition: prior to tempering treatment,plates may be subjected to an intermediate heat treatment.Welding of 9Ni is restricted to a maximum heat input of 3KJ/mm.EN 10028-4 X8Ni9, X7Ni9 grades which show equivalence to Lloyd's Register 9Ni can be accepted for approved applications.
NSSMC’s NSGP-2 Corrosion Resistant Steel Grades are approved as below:
Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM Condition fine grain treated with Al+Ti to athickness of 20mm with through thickness properties of Z35
Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM+Acc Condition fine grain treated with Al+Ti to athickness of 30mm with through thickness properties of Z35
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested inaccordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not implyconcessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC conditionup to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on eitherdesign or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does notimply concessions on either design or survey requirements.(Note CRL = Corrosion Ratio by Long term test)
NSSMC’s Steel Grades bearing Sn are approved as below:
Plates AH32, AH36, DH32 and DH36 in the TM condition fine grain treated with Al+Ti to a thickness of 25 mm with through-thickness properties of Z35
Plates AH32, AH36, DH32 and DH36 in the TM +Acc condition fine grain treated with Al+Ti to a thickness of 30 mm with through-thickness properties of Z35
Certificate No. MD00/1454/0029/1 Expiry date: 06/07/2019
314-0014
A 240Normal StrengthBarsNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
1, Nishino-choHigashi-Mukojima
Pipe & Tube UnitAmagasaki Works
Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:motomatsu.5q4.hiromiki@jp.nssmc.comCertificate No. MD00/1458/0009/1 Expiry date: 12/11/2019
Amagasaki, 660-0856
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
austenitic stainlessA.O.D./Con Cast
Carbon, Carbon manganese 400Rolled BarsSemi-Finished
As at 10 April 2018 58Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1850 MinatoWakayama-city
Wakayama Works (Wakayama & Kainan)
Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103
E-Mail: matsushita.6df.satoshi@jp.nssmc.com
Website: www.sumitomometals.co.jp
Approved for Semi-fhinished as rolled Round Billet with the diameter from 83mm to 400mm; As cast Round Billet with the diameter from 191mm to 453mm;As rolled Blooms 140mm x140mm to 550mm x 550mm; As cast Blooms 410mm x 530mm, 600mm x 670mm; As cast Slabs 700-1950mm x 227mm/250mm.
Certificate No. MD00/1748/0013/1 Expiry date: 24/06/2019
640-8555
A, B, D, E 50Normal StrengthSectionsNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
AH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Sakai cityOsaka
Wakayama Works [Sakai Area]1, Chikko Yawata-cho Sakai-Ku
Tel: +81 722 33 1179 Fax: +81 722 33 1185 Certificate No. MD00/4141/0005/1 Expiry: 08/07/2018
As belowE.A.F. / Con CastSteelmakingNIPPON YAKIN KOGYO Co., Ltd. YokohamaAs below, austenitic stainless 200SlabsSemi-Finished321, 347 10Austenitic StainlessPlates304L, 316L 53Fe-36Ni* 8Fe-Ni alloys304L, 316L, 321, 347 8Austenitic StainlessHot Rolled CoilFe-36Ni* 3Fe-Ni alloys
Kawasaki-kuKawasaki-shi
KAWASAKI PLANT4-2, Kojima-cho
Tel: +81 44 271 3045 Fax: +81 44 271 3044email mailto:kensuke.miura@nyk.co.jp web www.nyk.co.jp
Certificate No. MD00/1109/0008/1 Expiry date: 31/05/2018
* accepted for approved applications
Kanagawa - ken 210-8558
austenitic stainless 200E.A.F./V.O.D./Con CastSteelmakingNISSHIN STEEL CO. LTD Nagasaki304L, 316L, 304*, 316* 9Austenitic StainlessHot Rolled Coil
4976, Nomuraminami-machi,Shunan City,
SHUNAN WORKS
Tel: +81-3-3216-6327 Fax: +81-3-3214-6325
Website: www.nisshin.steel.co.jp
Cert No: MD00/4481/0001/1 Expiry Date: 13/05/2018
Yamaguchi Pref, 746 8666
304L, 316L, 321, 347 8Austenitic StainlessHot Rolled CoilNISSHIN STEEL CO., LTD. Kobe
Hekinan-shiAichi- ken
Kinuura Works1, Hama-cho
Tel: +81 566 48 7218 Fax: +81 566 48 1596 Email: nazuka.t343@nisshin-steel.co.jpWeb: http://www.nisshin-steel.co.jp/enCertificate No. MD00/2338/0009/1 Expiry date: 20/05/2020
447-8610
As belowE.A.F. / Con CastSteelmakingOJI STEEL CO., LTD. Yokohamacarbon, carbon-manganese 170BilletsSemi-FinishedA 25Normal StrengthBarsAH32, AH36 25Higher Strength
As at 10 April 2018 59Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Ota-cityGunma Pref.
Gunma Works120, Nittasorimachi-cho
Tel: +81 276 56 2119 Fax: +81 276 56 3136 Email: mailto:t-kudoh@oji-steel.co.jpWeb: www. oji-steel.co.jpCertificate No. MD00/1141/0007/1 Expiry date: 14/10/2017
370-0313
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. KobeHigher Strength 185Blooms/BilletsSemi-FinishedNormal Strength 190A 15Normal StrengthSectionsAH32, AH36 12Higher Strength
1 Chikko Yawata-choSakai
Sakai Works
Tel +81 722 33 3901 Fax +81 722 33 3976
Certificate No. MD00/0821/0010/1 Expiry date: 20/05/2019
Osaka
As belowE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. Kobecarbon, carbon-manganese, Normal Strength,Higher Strength
165Blooms/BilletsSemi-Finished
A, B, D 15Normal StrengthSectionsAH32, AH36 12Higher Strength
9-3 Minami Okajima 1 ChomeTaisho-ku
Osaka - Okajima Works
Tel: +81 06 6552 1447 Fax: +81 06 6552 3184 Email: ko-kisimoto@osaka-seitetsu.co.jpWeb :www.osaka-seitetu.co.jpCertificate No. MD00/1157/0007/1 Expiry date: 20/05/2019
Osaka 551-0021
alloy, austenitic stainlessE.A.F. / Con CastSteelmakingSANYO SPECIAL STEEL CO., LTD., KobeAs belowE.A.F. / Ingotcarbon, carbon-manganese, austenitic stainless 15Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless
380Blooms
A 220Normal StrengthBarsalloy 220MachineryU1, U2, U3 136Chain Cable Stock
Shikama-kuHimeji-shi
3007 Nakashima
Tel: +81 (0)792 35 6029 Fax: +81 (0)792 35 6027 email: taota@himeji.sanyo-steel.co.jp web: www.sanyo-steel.co.jp
Heat treatment sub contracted to Toyo Metal Treating Corporation, Takasago Plant No. 2, Takasago, Hyogo Pref., Japan.
Certificate No. MD00/1307/0013/1 Expiry date: 30/10/2019
672-8677
As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D, E 38Normal StrengthSectionsAH32, AH36, DH32, DH36 38Higher Strength
5, Shiohama-choSakai-ku, Sakai
Sakai Works
Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:h-ue@shinkansai-steel.co.jp Web: http://www.shinkansai-steel.co.jpCertificate No. MD00/0823/0010/1 Expiry date: 13/11/2020
Osaka 590-0981
As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher StrengthU1, U2, U3 80Chain Cable StockBars
4-26-1, Hoshida KitaKatano-shi
Hoshida Works
Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319 Email: h-ito@shinkansai-steel.co.jp Web: http://www.shikansai-steel.co.jpCertificate No. MD00/1244/0008/1 Expiry date: 05/10/2018
Osaka
As at 10 April 2018 60Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / IngotSteelmakingTHE JAPAN STEEL WORKS, LTD. YokohamaA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 65Austenitic StainlessAH32/304L, AH32/316L, AH32/316LN,AH32/317L
19Clad
AH32/S31803 30A/304L, B/304L, D/304L, E/304L, A/316L,B/316L, D/316L, E/316L
100
MuroranHokkaido
Muroran Plant4, Chatsu-machi
Tel +81 (0)143 22 0539 Fax +81 (0)143 22 5736 email: https://www.jsw.co.jp/en/contact/ web: www.jsw.co.jpCertificate No. MD00/1507/0008/1 Expiry date: 09/11/2018
051-8505
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingTOKAI SPECIAL STEEL CO., LTD. Kobecarbon, carbon-manganese 370BloomsSemi-Finishedcarbon, carbon-manganese 155Billets
Tokai-MachiTokai-shi
3, 5-Chome
Tel +81 52 603 7236 Fax +81 52 603 7229 email: komparu.58q.tomoaki@nssmc.co.jp
Certificate No. MD00/1542/0007/1 Expiry date: 01/02/2020
Aichi-ken
As belowE.A.F. / Con CastSteelmakingTOKYO STEEL MANUFACTURING CO., LTD. NagasakiA, B, D 32Normal StrengthPlates360AR, 410AR 32Boiler & Pressure VesselA 24Normal StrengthSections
Wakamatsu-kuKitakyushu City
Kyushu Plant3-5-1, Minami-Futajima
Tel: +81 93 701 2631 Mobile: +81 80 3974 1536 Fax: 81 93 791 2639 Email: mailto: ichikawa_y@tokyosteel.co.jp Web http://www.tokyosteel.co.jpCertificate No. MD00/1550/0009/1 Expiry date: 23/06/2017
Fukuoka 808-0109
As belowE.A.F. / Con CastSteelmakingTOPY INDUSTRIES, LTD. KobeE 20Normal StrengthSectionsA, B, D 35AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
20Higher Strength
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
20Ferritic Low Temperature
A, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
1, Akemi-choToyohashi-shi
Toyohashi Works
Tel +81 532 25 1111 Fax +81 532 25 7401 Email: mailto: s.miyashita@topy.co.jp web: http://www.topy.co.jpCertificate No. MD00/1555/0009/1 Expiry date: 15/06/2020
Aichi-ken, 441-8510
carbon, carbon-manganese, alloy 60E.A.F. / IngotSteelmakingTSUNEISHI IRON WORKS Co., Ltd Nagasaki
43-1 Koyo-machiWakamatsu-ward
Wakamatsu Steel Factory
Tel: +81 (0)93 752 0770 Fax:+86 (0)93 752 0777Email to: hideo.fukusada@tsuneishi.com Web: http://www.tsuneishi-iw.jp
Certificate No.: MD00/4392/0002/2 Expiry Date: 11/10/2020
Kitakyushu-city, 808-0002
As belowE.A.F. / Con CastSteelmakingYAMATO STEEL CO., LTD. KobeA, B, D, E 25Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
25Higher Strength
As at 10 April 2018 61Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
380, Kibi, Ohtsu-kuHimeji City
Tel: +81 (0)79 273 0716 Fax: +81 (0)79 272 0914 Email mailto: hmisumi@yamatosteel.co.jp Web:http://www.yamatokogyo.co.jpCertificate No. MD00/1687/00011/1 Expiry date: 09/06/2020
Hyogo-pref.
Korea
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347
8Austenitic Stainless SteelPlates from coilsBUSAN STEEL CO., LTD. Busan Port
29, Songjeuong-gil (Songjung-Dong),Gangseo-Gu
Tel: +82 51 831 3700, Fax No. +82 51 831 3701Email: gjj072@nate.comWebsite: www.busansteel.co.krCertificate No. MD00/4028/0002/1 Expiry date: 23/06/2018
Busan
304L, 304LN, 316L, 316LN 80Austenitic StainlessPlatesDK CORPORATION UlsanUNS S31803, UNS 32900*, UNS 32205* 50Duplex Stainless
66, Gohyeon-Gil, 98 Beon-gil,Cheongha-ri, Buk-gu, Pohang-si,
Tel: +82 (0)54 245 3062 Fax: +82 (0)54 245 3065 Email:mailto:hugging@dkcsteel.com Web:http://www.dkcsteel.com*accepted for approved applicationsThe scope of approval is for the heat treatment and final testing of plates only from rolled plates supplied from approved works.Certificate Number: MD00/2230/0007/1 Expiry: 28/05/2019
Kyungsangbuk-do
A 12Normal StrengthSectionsDONG IL STEEL CO. LTD Busan PortAH32, AH36 12Higher Strength
50, Daedong-ro,193, Beon-gil, Sasang-gu,
SASANG WORKS
Tel No. + 82-51-323-1177 Fax No: + 820 - 325 6378
Website: www.dongilsteel.com
Certificate No: MD00/4517/0001/1 Expiry Date: 14/10/2015
Busan
carbon-manganeseE.A.F. / Con CastSteelmakingDONGKUK STEEL MILL Co. Ltd. Ulsancarbon-manganese 480Blooms/BilletsSemi-FinishedD, E 50Normal StrengthPlatesA, B 83AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
50Higher Strength
460FG, 490FG, 510FG 35Boiler & Pressure Vessel360AR, 410AR 40360FG, 410FG 50LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
D 25Normal StrengthSectionsA, B 32AH27S, DH32 25Higher StrengthAH32, DH27S 32
195, Cheolgangsandan-ro,Daesong-myeon, Nam-gu,
Pohang Works
Tel: +82 054 721 3261 Fax: +82 02 317 9055email: jongho.chun@dongkuk.com web: www.dongkuk.comCertificate No. MD00/0414/0014/1 Expiry date: 13/05/2019
Billets to 150 x 150mm, Blooms to 200 x 250 & 250 x 300, Beam Blanks to 400 x 480 x 120mm.
Pohang-si, Gyeongsangbuk-do
E 83Normal StrengthPlatesDONGKUK STEEL MILL Co. Ltd. SeoulA, B, D 100FH32, FH36 50Higher StrengthAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40
83
460AR 35Boiler & Pressure Vessel360AR, 410AR 40490FG 50460FG, 510FG 70360FG, 410FG 100LTFH32, LTFH36 50Ferritic Low Temperature
As at 10 April 2018 62Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
25, Godaegongdan 1-gil,Song-ak-eup, Dangjin-si,
Dangjin Works
Tel: +82 (0) 41 351 4679 Fax: +82 (0) 41 317 9083 Email: dongjin.kim@dongkuk.com Web: http://www.dongkuksteel.co.kr
Certifcate Number: MD00/3773/0010/1 Expiry: 10/04/2019
Plates in the Normalised supply condition Fine Grain Al+V are only accepted in the thickness range >30mm to 70mm.
Approval includes Z grade plates with specified through thickness properties when tested in accordance with LR Rules requirements.
Chungcheongnam-do
A 20Normal StrengthPlates from coilsDONGYANG S.TEC. CO., LTD Ulsan
#619-12, Munduk-Ri,Ocheon-Eup Nam-Gu,
Tel: +82 54 292 6181 Fax: +82 54 291 6548Email: kyb4621@hanmail.netWebsite www.dystec.co.krCertifcate Number: MD00/3840/0003/1 Expiry date: 26/09/2016
Pohang-city, Kyeongbuk,
carbon 16Structural SectionsFabricated SectionsDONGYEUN STEEL Co., LTD Busan Port
Jangan-eup,Gijang-gun,
Tel No: 0151 724 7800 Fax No: 051-724-8901
E-mail: bhoh@dongyeunsteel.com & jkhong@dongyeunsteel.com
Website: www.dongyeunsteel.com
Certificate No. MD00/4650/0001/1 Expiry Date: 09/01/2020
Busan.
As belowE.A.F. / IngotSteelmakingDOOSAN HEAVY INDUSTRIES & CONSTRUCTIONCO., LTD.
Changwon
carbon, carbon-manganese, alloy, austeniticstainless
500Ingots (tonnes)Semi-Finished
Seongsan-gu,Changwon,
Changwon Plant22, Doosanvolvo-ro,
Tel +82 55 278 4746 Fax no. +82 55 278 8506youngsu.bae@doosan.com web www.doosanheavy.comCertificate No. MD00/0883/0002/1 Expiry date 08/03/2019
Kyungnam,
B, D, E 18Normal StrengthSectionsFINE BESTEEL CO LTD ChangwonA 30DH32, DH36, EH32, EH36, FH32, FH36 18Higher StrengthAH27S, AH32, AH36 30LTAH32, LTDH32, LTEH32, LTFH32, LTFH36 18Ferritic Low Temperature
25-1 Ha-Ri, Changnyeong-Up,Changnyeong-Gun,
Tel: +82 (0)55 259 2076 / 2064 Fax: +82 (0)55 259 2070Email: sungjh@finebesteel.comWeb www.fine-besteel.comCertificate No. MD00/3659/0006/1 Expiry date: 09/09/2018
Gyeongnam,
As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Seoulcarbon, carbon-manganese 270BloomsSemi-Finishedcarbon, carbon-manganese 200BilletsA, B 32Normal StrengthSectionsAH27S, AH32, AH36 32Higher Strength
63, Jungbong-DaeroDong-Gu
Inchon Plant
Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: arom@hyundai-steel.com Web: http://www.hyundai-steel.comSections flat bars up to 400 mm width.
Certificate No. MD00/0754/0011/1 Expiry date: 01/01/2020
Inchon
As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Ulsancarbon, carbon-manganese, alloyBlooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 120BarsB, D, E 18Normal StrengthSectionsA 37AH27S, AH40, DH27S, DH40, EH27S, EH32,EH36, EH40, FH27S, FH32, FH36, FH40
18Higher Strength
As at 10 April 2018 63Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
KoreaAH32, AH36, DH32, DH36 37Higher StrengthSectionsHYUNDAI STEEL COMPANY UlsanLTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, LTFH40
18Ferritic Low Temperature
carbon, carbon-manganese, alloy 120MachineryBarsR3S, R4 110Chain Cable StockU1, U2, U3, R3 150
6363, Donghaean-roNam-Gu, Pohang-si
Pohang Plant No. 1
Tel: +82 54 271 1479 Fax: +82 54 271 1512 Email: mailto:2007372@hyundai-steel.com Web: http://www.hyundai-steel.comCertificate No. MD00/0819/0017/1 Expiry date: 05/06/2019
Gyeongsangbuk-do
carbon-manganeseE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY UlsanA, B, D 16Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
16Higher Strength
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
16Ferritic Low Temperature
carbon, carbon-manganese, alloy 120Semi-finished ProductsBars
36, Cheolgang-ro 314 beon-gil,Nam-Gu, Pohang-si,
Pohang Plant No. 2
Tel No. +82 54 271 1479 Fax No. +82 54 271 1512Email mailto:2007372@hyundai-steel.comWeb: www.hyundai-steel.com Certificate No. MD00/3084/0009/1 Expiry date: 04/06/2019
As BelowB.O.S./E.A.F./Con CastSteelmakingHYUNDAI STEEL COMPANY SeoulNormal strength, Higher Strength 300SlabsSemi-FinishedA, B 22Normal StrengthHot Rolled CoilAH32, AH36 22Higher StrengthA, B 22Normal StrengthPlates from coilsAH32, AH36 22Higher Strength
Songak-eupDangjin-si
HR Coil Plant1480, Bukbusaneop-ro
Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; jwmking@hyundai-steel.com Web: http://www.hyundai-steel.comSlabs with nominal 2200mm width x nominal 4400mm length Certificate No. MD00/3446/0005/1 Expiry date: 22/03/2020
Chungncheongnam-do
A, B, D, E 100Normal StrengthPlatesHYUNDAI STEEL COMPANY SeoulAH42, AH46, AH50, DH42, DH46, DH50, EH42,EH46, EH50, FH40, FH42, FH46, FH50
50Higher Strength
FH27S, FH32, FH36, EH40* 80EH47 83AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40,EH40S**
100
360AR, 410AR, 460AR 40Boiler & Pressure Vessel460FG, 490FG 83360FG, 410FG 100LTDH27S, LTDH32, LTDH36, LTFH27S,LTFH32, LTFH36
40Ferritic Low Temperature
As at 10 April 2018 64Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Songak-EupDangjin-Si
Dangjin Works1480, Bukbusaneop-ro
Tel: +82 41 680 1690 or 1685 Fax +82 41 680 1699 email; jwmking@hyundai-steel.com web: http://www.hyundai-steel.com
Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to35.0mm.Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Tisupply condition are restricted to the thickness range >15.0mm to 83.0mm.Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted tothe thickness range >15.0mm to 40.0mm.Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.Plates with specified through thickness properties may be accepted with the suffix Z35.EH40* is approved with demonstrated brittle crack arrest properties.Approved for corrosion resistant steel plates in grades AH27S RCB and AH32 RCB with Z35 through thickness properties to 40 mm maximum thickness in TMsupply condition with Al+Nb+Ti grain refining treatment.
Certificate Number: MD00/3761/0015/1 Expiry: 22/03/2019
Chungcheongnam-do
As belowE.A.F. / IngotSteelmakingHYUNDAI STEEL COMPANY Changwoncarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished
Haeryong-myeonSuncheon City, Jeollanam-do
46, Yulchonsandan 5-ro
Tel: +82 61 760 7100 Fax: +82 61 725 7733 email: kimlh@spp.co.kr web: www.sppycenergy.co.kr
Certificate Number: MD00/3866/0005/1 Expiry date: 11/12/2019
Zip code: 540856
carbon, carbon-manganese, alloy 123MachineryBarsJINYANG SPECIALTY STEEL Co., Ltd. Ulsan
Yeongcheon-si,Gyeongsangbuk-do,
149-9, Damtteul-gil,
Tel: +82 (0)54 335 3500 Fax: +82 (0)54 335 0355 Email: jysteel@jysteel.co.krWeb: http:// www.jysteel.co.kr/mainCert No MD00/3897/0002/1 Expiry date: 22/03/2017
As belowE.A.F. / IngotSteelmakingKISCO Changwoncarbon, carbon-manganese, alloy 160Ingots (tonnes)Semi-Finished
ChangwonGyeongnam
12, Gongdan-ro103 beon-gil, Seongsan-gu
Tel +82 55 260 0746 Fax +82 55 282 4123 Email: ojyworld@kisco.co.kr Web page http://www.kisco.co.kr
Certificate No. MD00/0884/0006/1 Expiry date: 10/01/2021
A 15Normal StrengthSectionsKOREA STEEL SHAPES CO., LTD Busan PortAH32, AH36, DH32, DH36, EH32, EH36 15Higher StrengthA 65Normal StrengthBarsAH32 30Higher Strength
84, Noksansandan 407-Ro,Gangseo-Gu
Noksan Works
Tel: +82 51 310 8912 Fax: +82 51 831 3951email nawoo1@ekosco.com web www.ekosco.com
Certificate No. MD00/3096/0009/1 Expiry date: 20/01/2020
Busan,
As belowE.A.F. / Con CastSteelmakingKOREA STEEL SHAPES CO., LTD Changwoncarbon, carbon-manganese, Normal Strength,Higher Strength
220BilletsSemi-Finished
98, Gongdandong-gil, Chilseo-Myeon,Haman-Gun,
Chilseo Works
Tel: +82 55 589 1159 Fax: +82 55 589 1116email: stmjslee@ekosco.com web: www.ekosco.com
Certificate No. MD00/3097/0002/1 Expiry date: 10/10/2017
Gyeongnam,
As at 10 April 2018 65Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
austenitic stainless 85MachineryBarsKWANG JIN IND CO. LTD. Busan Portalloy 93carbon, carbon-manganese 100
160, Hasinjungang-ro,Saha-gu,
Tel No: +82 51 220 9264 Fax No. +82 51 204 9172Email: mgkang@kjsteel.co.krWeb Address www.kjsteel.co.krCert No MD00/3758/0003/1 Expiry date 14.03.2019
Busan,604-030
As belowB.O.S. / Con CastSteelmakingPOSCO Gwangyang Works ChangwonNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH40, DH40, EH40, EH47 80Higher StrengthFH36, FH40 90AH27S, AH32, AH36, AH62, AH69, DH27S,DH32, DH36, DH62, DH69, EH27S, EH32, EH36,EH62, EH69, FH27S, FH32
100
360AR, 410AR, 460FG, 490FG, 510FG 35Boiler & Pressure Vessel360FG, 410FG 80LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
40Ferritic Low Temperature
A, B, D 22Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 12Boiler & Pressure Vessel
Gwangyang-si,Jeollanam-do,
20-26, Pokposarang-gil,
Tel: +82 2 3457 3838 Fax: +82 2 3457 6419 Email: ayoung89@posco.com Web: www.posco.comApproved for semi-finished products, slabs, nominal 1750mm wide x 6000mm long.Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.Certificate Number: MD00/3086/0015/1 Expiry: 13/07/2020
545-711
As BelowB.O.S./E.A.F./Con CastSteelmakingPOSCO Pohang Works Ulsancarbon, carbon-manganese, alloy, Normalstrength, Higher Strength
400SlabsSemi-Finished
A, B, D, E 100Normal StrengthPlatesFH27S, FH32, FH36 83Higher StrengthAH40, DH40, EH40 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, EH40S*, EH47
100
360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
304L, 304LN, 316L, 316LN 80Austenitic StainlessUNS S31803, UNS 32900*, UNS 32205* 50Duplex StainlessA, B, D, AH32, AH36, DH32, DH36 35TaperedE 12Normal StrengthHot Rolled CoilA, B, D 22EH27S, EH32, EH36 16Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36 22460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22304L, 316L 8Austenitic Stainless
Nam-gu,Pohang si,
(Goedong-dong), 6261, Donghaean-ro,
Tel: +82 2 3457 3838 Fax: +82 2 3457 6000 email: ayoung89@posco.com web: www.posco.com
Certificate No. MD00/1206/0022/1 Expiry date: 29/04/2019
* EH40S grade is approved with demonstrated crack arrest properties.
Applicable plate grades may be accepted with through thickness properties when manufactured and tested in accordance with the relevant Rules.
Slabs as semi-finished products nominal maximum width 2200mm x nominal maximum length 5000mm to the above maximum thickness are approved forfurther processing for rolled and forged products
Gyeongsangbuk-do,
As at 10 April 2018 66Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 18Normal StrengthPlates from coilsS & STEEL CO., LTD. Busan PortAH36 10Higher StrengthAH27S, AH32 15
1620 Dadae-dong, Saha-guBusanTel: +82 51 262 7525 Fax: +82 51 924 7902 Email: taxibill@sdstl.co.uk Web: http://www.sdstl.co.krCertificate No. MD00/3523/0006/1 Expiry date: 23/09/2017
As belowE.A.F./Ingot/Con CastSteelmakingSeAH BESTEEL CORPORATION Mokpocarbon, carbon-manganese, alloy 155Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 510Bloomscarbon, carbon-manganese 180Billetsalloy 350Barscarbon, carbon-manganese, alloy 300MachineryBarsR5 140Chain Cable StockR4S, R4S 146R4 155U1, U2, U3, R3, R3S 165
Gunsan CityJeonlabuk-Do
Gunsan Plant1-6, Soryong-Dong
Tel: +82 63 460 8078 Fax: +82 63 460 8099 email: jiwon.yoo@seah.co.kr web: www.seah.co.kr
Certificate No. MD00/1749/0014/1 Expiry date: 04/04/2018
Approval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3Sand R4 to Pu Sung Metal Co., Ltd.Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mmdiameter x 3050mm long, to the above maximum weight approved for further processing for forgings. Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings andRolled Products. Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled Products.Alloy grade bars as semi-finished products nominal maximum length 12,000mm to the above maximum diameter are approved for further processing for forgedproducts.
As belowE.A.F. / IngotSteelmakingSeAH CHANGWON INTEGRATED SPECIAL STEEL Changwonduplex stainless 17Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless
150
carbon, carbon-manganese, alloy, duplexstainless
150StructuralBars
austenitic stainless 170carbon, carbon-manganese, alloy 150Machinery
Seongsan-GuChangwon,
CORPORATION147,Jeokhyeon-Ro
Tel: +82 (0)55 269 6200 Fax: +82 (0)55 269 6907 Email: junkon@poscoss.com http://www.poscoss.comCertificate No. MD00/1294/014/1 Expiry date: 07/08/2020
Gyeongnam
As belowE.A.F./V.O.D./Con CastSteelmakingTAEWOONG CO., LTD. Busan PortAs belowE.A.F/A.O.D/Ingotaustenitic stainless 30Ingots (tonnes)Semi-Finishedalloy 100carbon, carbon-manganese 150austenitic stainless 600Bloomscarbon, carbon-manganese, alloy 800
15, Hwajeonsandan 1-ro,Gangseo-gu,
Taewoong Steelmaking Business Unit
Tel: +82-51-329-5142 Fax: +82-51-329-5141
E-mail: chaehwan.kang@taewoong.com
Website: www.taewoong.com
Certificate No: MD00/4662/0002/1 Expiry Date: 20/02/2020
Busan, 46740.
As at 10 April 2018 67Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingYK STEEL CORP. Busan PortA 7Normal StrengthSectionsA 32Normal StrengthBars
Saha-Gu604-817
760 Eulsukdo-daero,
Tel. +82 (0)51 260 2186 Fax +82 (0)51 265 2399 Email: hdkim@yksteel.co.kr Web: http://www.yksteel.co.krCertificate No. MD00/0650/0008/1 Expiry date: 25/05/2017
Busan
304L, 316L 13Austenitic Stainless SteelPlates from coilsYOUNG GWANG STAINLESS CO., LTD. Busan PortUNS S32750 6Duplex StainlessUNS S31803 8
Gangseo-guBusan
16, Noksansandan 262-ro
Tel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: kbj@ygs.co.kr Web: http://www.ygs.c.kr
Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018
304L, 316L 13Austenitic Stainless SteelPlates from coilsYOUNG GWANG STAINLESS CO., LTD. Busan PortUNS S32750 6Duplex StainlessUNS S31803 8
406, Noksansaneopjung-roTel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: kbj@ygs.co.kr Web: http://www.ygs.c.kr
Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018
Luxembourg
As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonNormal Strength, Higher Strength 100BloomsSemi-FinishedA, B 26Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
26Higher Strength
66 rue de LuxembourgL4009 Esch sur Alzette
BELVAL MILLTMB Rolling Plant
Tel: +352 58 2885 Fax: +352 5835 81 Email: mailto:roberto.klecker@arcelor.comWeb:www.arcelor.comCertificate #: MD00/0030/0008/1 Expiry date: 04/11/2018
As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonHigher Strength 135BloomsSemi-FinishedA, B 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher StrengthSections
L 4009 Esch sur AlzetteDifferdange Mill
Tel: +352 58 2028 85 Fax: +352 5835 81 Email: roberto.klecker@arcelormittal.com Web http://www.arcelormittal.comBeam Blanks as semi-finished products (referred to as blooms above) nominal 500mm overall width x nominal 1150mm overall length, to the above overallmaximum thickness Certificate Number: MD00/0032/0008/1 Expiry: 10/03/2019
A, B 30Normal StrengthSectionsARCELORMITTAL RODANGE ET SCHIFFLANGE LyonAH32, AH36, DH32, DH36 30Higher Strength
2, Rue de L'industrieL-4801 Rodange
Rodange Mill
Tel: +352 58 20 28 84 Fax: +352 58 20 35 81 email: :stephane.arnault@areclormittal.com web www.arcelor.comCertificate No. MD00/2266/0007/1 Expiry date: 16/01/2019
As at 10 April 2018 68Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Macedonia
A 35Normal StrengthFabricated SectionsFAKOM A.D. BeogradAH36, DH36, EH36 40Higher Strength
POB 4391000 SKOPJE
St. Aleksandar Makedonski No.5
Tel No.: +389 317 4023, Fax: +389 317 3564 email: mailto:info@fakom.com.mk Web http://www.fakom.com.mkCertificate No. MD00/2856/0008/1 Expiry date: 26/11/2018
As belowE.A.F. / Con CastSteelmakingMAKSTIL A.D.- SKOPJE BeogradA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 50360FG, 410FG 100
XVI Makedonska brigada 18P.O. Box 599
Tel: +389 2 328 7130 email: igor.bogeski@makstil.com.mk web www.makstil.comSpecified through thickness properties for plates up to 50 mm thicknessCertificate No. MD00/2216/0008/1 Expiry date: 21/05/2019
1000-Skopje
Malaysia
A 30Normal StrengthPlatesJI KANG DIMENSI Sdn. Bhd. Kuala Lumpur
26100 KuantanPahang Darul Makmur
Lot 69-71, Kawasan Perindustrian Gebeng
Tel: +609 583 9881 Fax: +609 583 4551 Email: mailto: limf555@163.comWeb: www.jikangdimensi.comCertificate No. MD00/3022/0005/1 Expiry date: 27/06/2018
Mexico
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingARCELORMITTAL LAZARO CARDENAS, S.A. deC.V.
Metepec/Veracruz
carbon, carbon-manganese 250SlabsSemi-Finished
60950- Lázaro CárdenasMichoacan
Av Francisco J. Mujica N° 1-B
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperatureservice according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible forordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
Tel: +52 753 533 1917 Fax: +52 753 533 1187 Email: berenice.serrano@arcelormittal.com Web http://www.arcelormittal..comCertificate No. MD00/0783/0007/1 Expiry date: 08/01/2017
As at 10 April 2018 69Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Montenegro
Carbon, Carbon-manganese, Alloy 7EAF/LRF/VD/IngotSteelmakingTOS�ELIK NIKŠI� d.o.o. Beograd
Vuka Karadzica bb,81400 NiksicTel: +382 40 202 222 email: drago.zizic@toscelikniksik.me
Certificate No: MD00/4508/0001/1 Expiry Date: 03/09/2018
Norway
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingCELSA ARMERINGSSTÅL AS OsloA, carbon, carbon-manganese 160BilletsSemi-Finished
PO Box 500N-8601 Mo i Rana
Mo Industripark
Tel: +47 91886913 Mob: +47 911 10493 Email: asbjorn.myrvoll@celsanordic.com Web http://www.celsanordic.comCertificate No. MD00/2103/0007/1 Expiry date: 05/09/2020
Poland
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingALCHEMIA S.A. Katowice
carbon, carbon-manganese, alloy, austeniticstainless
14Ingots (tonnes)Semi-Finished
ul.Dyrekcyjna 641-506 Chorzów
ODDZIAL STALOWNIA BATORY W CHORZOWIE
Tel: +48 883 301310
E-mail: h.badura@alchmiasa.pl
Website: www.alchemiasa.pl
Certificate No. MD00/0711/0013/1 Expiry date: 05/10/2019
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 220SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilAH27S, AH32 16Higher StrengthA, B, D 15Normal StrengthPlates from coilsAH27S, AH32 16Higher Strength410 FG, 360 FG, 460 FG 16Boiler and Pressure Vessel
30-969 Kraków
ODDZIAL W KRAKOWIEul. Ujastek 1
Tel: +48 12 290 1817 Fax: +48 12 290 5591email: andrzej.zajac@arcelormittal.com web: www.arcelormittal.com/poland
Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm widthand 11000mm length.Coils and plates are approved to maximum 2100mm width.
Certificate #: MD00/0707/0012/1 Expiry date: 25/01/2020
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 300SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 280Blooms/Billets
41-308 Dabrowa Gornicza
Oddzial w Dabrowie GorniczejAl. J. Pilsudskiego 92
Tel: +48 32 776 87 14 Fax: +48 32 776 84 86 Email wojciech.michalczyk@arcelormittal.com Web: http://www.arcelormitta.com/poland/
Certificate No. MD00/0717/0011/1 Expiry date: 05/02/2018
As belowE.A.F./Ingot/Con CastSteelmakingARCELORMITTAL WARSZAWA Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 25Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 220Blooms/Billetscarbon, carbon-manganese, alloy 65StructuralBarscarbon, carbon-manganese, alloy 65Machinery
As at 10 April 2018 70Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
ul. Kasprowicza 13201-949 WarszawaTel: +48 22 835 8081 Fax: +48 22 835 8638Email: mailto:beata.pietrzyk@arcelormittal.com Web: http://www.arcelormittal-warszawa.comCertificate No. MD00/0720/0008/1 Expiry date: 01/08/2018
As belowE.A.F. / IngotSteelmakingCELSA "HUTA OSTROWIEC" Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 130Ingots (tonnes)Semi-Finished
ul. Samsonowicza 227-400 Ostrowiec Swietokrzyski
ZAKLAD WYROBOW KUTYCH
Tel: +48 (0)41 2492905
E-Mail: martynowski@celsaho.com
Web page http://www.celsaho.com
Certificate No. MD00/2006/0008/1 Expiry date: 24/10/2019
Ingots size maximum 130 MT 2.33 m diameter
As belowE.A.F. / Con CastSteelmakingCMC POLAND Sp. z.o.o. Katowicecarbon, carbon manganese 160Blooms/BilletsSemi-FinishedA, B, D 25Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength
ul. Pilsudskiego 8242-400 ZawiercieTel: +48 32 672 5353 Fax: +48 32 672 5134 Mobile: +48 695 105211 Email: anna.slomka@cmc.com Web: www.cmcpoland.comCertificate No. MD00/3594/0005/1 Expiry date: 05/05/2018
Approval for sections covers wide flats to 200mm width and flat bars to 150mm width.
.
As belowE.A.F. / Con CastSteelmakingCOGNOR S.A. Katowicecarbon, carbon-manganese, alloy 160BilletsSemi-Finished
ul. Zawadzkiego 4744-109 Gliwice
ODDZIAL FERROSTAL LABEDY W GLIWICACH
Tel: +48 32 234 7600 Fax: +48 32 234 7650 Mob +48 508032685EMail mailto:biuro@ferrostal.com.pl Web page http://www.ferrostal.com.plCertificate No. MD00/2307/0007/1 Expiry date: 29/03/2020
Carbon, Carbon-manganese, Alloy 15EAF/LRF/VD/IngotSteelmakingCOGNOR S.A. Katowicecarbon, carbon-manganese, alloy 15Ingots (tonnes)Semi-Finished
ul.Kwiatkowskiego 1,37-450 Stalowa Wola
Oddziaž HSJ w Stalowej Woli
Tel: +48 15 813 51 84 Fax: +48 15 844 23 06email: hsj@hsjsa.pl web: www.hsjsa.pl
Certificate No: MD00/4745/0001/1 Expiry Date: 26/03/2021
Carbon, Carbon-Manganese, Alloy 300Rolled BilletsSemi-FinishedHUTA BANKOWA Sp. z o.o. KatowiceCarbon, Carbon-manganese, Alloy 250Rolled Round BarsA, B 20Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strengthcarbon, carbon-manganese 250StructuralBarscarbon, carbon-manganese, alloy 250MachineryU1, U2 160Chain Cable Stock
ul. Sobieskiego 2441-300 Dabrowa GórniczaTel +48 32 295 7477Email: a.krawczyk@hutabankowa.pl;w.paterek@hutabankowa.pl Web http://www.hutabankowa.com.plCertificate No. MD00/0716/0009/1 Expiry date: 04/03/2019
A, B, D, E 100Normal StrengthPlatesHW PIETRZAK HOLDING Sp. z o.o. KatowiceAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100A/304L 50Clad
As at 10 April 2018 71Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
41-506 Chorzów
Oddzial Walcownia Blach Batory w Chorzowieul. Lesna 42
Tel: +48 604936263 or +48 32 7722525 email: beata.brzoza-kwiatek@p-h.plweb: www.pietrzak-holding.pl
All plates with specified through thickness propertiesCertificate No. MD00/2766/0007/1 Expiry date: 17/10/2016
As belowE.A.F. / Con CastSteelmakingISD HUTA CZESTOCHOWA Sp. z o.o. Katowicecarbon, carbon-manganese 250SlabsSemi-Finishedcarbon, carbon-manganese 280BloomsE 50Normal StrengthPlatesA, B, D 75AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR, 460AR, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel360FG, 410FG 75
42-207 Czestochowaul. Kucelinska 22
Above plate grades may also be supplied with Z25/Z35 through thickness property requirements.
Tel: +48 34 323 8147 Fax: +48 34 323 0034 Email: marketing@isd-hcz.com.pl Web: http://www.isd- hcz.com.plCertificate No. MD00/0713/0013/1 Expiry date: 05/04/2018
carbon, carbon-manganese, alloy 150StructuralBarsWALCOWNIE BRUZDOWE "BATORY" Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 150Machinery
41-500 Chorzówul. Zelazna 22
Tel: +48 32 241 77 38 Fax: +48 32 241 77 55email sowinska.lilianna@wbb.net.pl web: www.wbb.net.pl
Certificate No. MD00/3545/0003/1 Expiry date: 30/11/2017
Romania
As belowB.O.S./Ingot/Con CastSteelmakingARCELORMITTAL GALATI S.A. GalatzA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
800698 GalatiSos Smardan Nr.1
Tel: +40 236 802100 Fax: +40 236 802101
E-mail: fanel.zamfir@arcelormittal.com
Website: www.arcelormittal.com
Approval includes for plates with specified through thickness properties, designation Z35, in all grades up to 60 mm thickness in the normalized condition.
Certificate No. MD00/0333/0009/1 Expiry date: 01/12/2019
As belowE.A.F. / Con CastSteelmakingCOS TARGOVISTE S.A. Galatzcarbon, carbon manganese, Alloy 150Blooms/BilletsSemi-FinishedU1, U2, U3 95Chain Cable StockBars
Sos. Gaiesti, 9-11Jud Dambovita, 130087
Targoviste
Tel: +40 758 837 264 Fax: +40 245 213 322 email: dumitru.dumitru@cos-tgv.ro Web: www.cos-tgv.ro
Certificate No. MD00/2293/0007/1 Expiry date: 12/02/2020
carbon, carbon-manganese, alloy 250E.A.F. / IngotSteelmakingDOOSAN IMGB S.A Galatzcarbon, carbon-manganese, alloy 250Ingots (tonnes)Semi-Finished
Berceni Road Nr. 104Sector 4
Tel: +40 21 301 2849 Fax: +40 21 301 2502 E-mail: mihai.ciorneanu@doosan.com
Web: www.doosanimgb.com
Certificate No. MD00/1259/0003/1 Expiry date: 08/09/2020
041919 Bucharest
As at 10 April 2018 72Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese, alloy 250StructuralBarsS.C. DONALAM S.R.L Galatzcarbon, carbon-manganese, alloy 150Machinery
Str. Prelungirea Bucuresti, nr 162,910125 CalarasiTel: +40 242 307 500 Fax: +40 242 306 913email: sales@donalam.ro web: www.grupobeltrame.com
Certificate No: MD00/4439/0001/1 Expiry Date: 05/03/2018
A 50Normal StrengthSectionsS.C. LAMINORUL S.A. - BRAILA GalatzAH27S, AH32, AH36, DH32, DH36 12Higher StrengthA 50Normal StrengthBars
810461 BrailaSos. Industria Sarmei nr. 2
Tel +40 239 669 388 Fax +40 374 092 038 Email: secretariat@laminorul.ro
Website: www.laminorul.ro
Certificate No. MD00/1916/0009/1 Expiry date: 29/03/2018
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingTMK-RESITA S.A. Galatzalloy 177BilletsSemi-Finishedcarbon, carbon-manganese 280
Traian Lalescu No. 36Caras-SeverinTel: +40 (0)255 217211 Fax: +40 (0)255 211883 Email: office.resita.tmk-artrom.roWeb http://www.tmk-artrom.roCertificate No. MD00/3804/0003/1 Expiry date: 07/07/2019
Russia
A, B, D 14Normal StrengthSections"RM - steel" Ltd. St. PetersburgAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36
14Higher Strength
11, Sedova street192019, St PetersburgTel: +7 812 318 0015 Fax: +7 812 568 0015 Email: mailto:info@rm-steel.com Web http//www.rm-steel.comCertificate No. MD00/1910/0010/1 Expiry date: 14/01/2020
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingCHELYABINSK METALLURGICAL PLANT PAO St. Petersburgcarbon, carbon-manganese, alloy 20Ingots (tonnes)Semi-Finished
2nd Paveletskaya ul, 14454047- Chelyabinsk
Tel; +7 351 725 57 27 Fax: +7 351 725 51 76email sale-chmk@mechel.ru web: www.mechel.ruIngots supllied as semi finished products are for further processing for forgings.Certificate No. MD00/3262/0007/1 Expiry date: 10/08/2018
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingJOINT STOCK COMPANY St. PetersburgNormal strength, Higher Strength 300SlabsSemi-Finished
1, Metallurgov Str.,Nizhny Tagil,
"EVRAZ NIZHNY TAGIL METALLURGICAL PLANT"
Tel:+007 3435 490611 Fax:+007 3435 496169 Email:mailto:alexander.ashihin@ur.evraz.com Web http://www.ntmk.ruCertificate No. MD00/2660/0007/1 Expiry date: 04/04/2018
Sverdlovsk Region, 622025
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingJOINT STOCK COMPANY St. Petersburgcarbon, carbon-manganese, Normal Strength,Higher Strength
300BloomsSemi-Finished
U1, U2, U3 80Chain Cable StockBars
309515, BelgorodStary Oskol
"OSKOL ELECTROMETALLURGICAL PLANT"pr. Alekseya Ugarova 218/2
Tel +07 4725 375364 Fax +07 4725 373755 vformin@oemk.ru Web http://www.oemk.ruBlooms as semi finished products; normal strength and higher strength; nominal 360mm maximum width x nominal 12,000mm maximum length.Blooms as semi finished products; carbon and carbon-manganese; nominal 360mm maximum width x nominal 12,000mm maximum length.Certificate Number: MD00/3065/0006/1 Expiry: 24/02/2019
As at 10 April 2018 73Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingJSC ''Ural Steel'' St. PetersburgB, D 40Normal StrengthPlatesA 50AH32, AH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
NovotroitiskOrenburg Region
1, Zavodskaya Street
Tel: +7 3537 66 20 66 Fax: +7 3537 66 25 27 Email: steel@metalloinvest.com Web: http://www.uralsteel.comCertificate No. MD00/2337/0009/1 Expiry date: 30/03/2020
462353
As belowE.A.F/A.O.D/IngotSteelmakingJSC KIROVSKIY ZAVOD St. Petersburgcarbon, carbon-manganese 120Semi-finished ProductsBars
47 Stachek Prospect198097 St. Petersburg
Petrostal Steel Works
Tel: +7 812 702 02 23 Fax: +7 812 702 04 66 email: paa@petrostal.spb.ru web: http://www.petrostal.spb.ru
Certificate No. MD00/1751/0007/1 Expiry: 29/01/2018
As belowE.A.F./Ingot/Con CastSteelmakingMOTOVILIKHA-GRAZHDANSKOYEMASHINOSTROENIE, LLC
St. Petersburg
carbon 17Ingots (tonnes)Semi-Finished
As below 450Blooms/Billets
614014, Perm1905 Street, 35Tel +8 342 260 7317 Fax +8 342 260 7959 Email: kamasteel@mz.perm.ru Web: http://www.mzperm.ruCertificate No. MD00/4608/0002/1 Expiry date: 08/09/2019
As belowB.O.S. / Con CastSteelmakingNovolipetsk Steel St. PetersburgNormal strength, Higher Strength 355SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH36, EH40
12Higher Strength
460FG, 490FG 10Boiler & Pressure Vessel360, 410, 360FG, 410FG 16
Pl. Metallurgov 2, NLMKLipetsk
398040, Russia
Tel: +7 795 034 44 45
Email: sales@nlmk.ru & drp@nlmk.com
Web:http://www.nlmk.ru
Certificate No. MD00/1124/0007/1 Expiry date: 04/11/2019
A, B, D, E 40Normal StrengthPlatesPAO SEVERSTAL St. PetersburgEH27S, EH32 32Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH40
40
360, 410 32Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
30 Mira Street162699 Cherepovets
Rolling Mill 2800
Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:sales@stal.ru Web http://www.severstal.ruPlates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.Plates in the Normalizing rolled condition to 2200mm maximum width.Certificate #: MD00/0298/0011/1 Expiry date : 12/06/2019
Vologda Region
A 15Normal StrengthPlatesPAO SEVERSTAL St. PetersburgA, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
12Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel
30 Mira StrRolling Mill 2000
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: sales@stal.ru Web http://www.severstal.ruCertificate No. MD00/2801/0008/1 Expiry date: 12/06/2019
As at 10 April 2018 74Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
D, E 50Normal StrengthPlatesPAO SEVERSTAL St. PetersburgA, B 70AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
70Higher Strength
"IZHORSKIE ZAVODY"196651 Kolpino
Rolling Mill 50001, Lenina Prospect
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:sales@stal.ru Web http://severstal.ruPlates with specified through thickness propertiesCertificate #: MD00/2802/0007/1 Expiry date: 12/06/2019
St Petersburg
As belowB.O.S. / Con CastSteelmakingPAO SEVERSTAL St. PetersburgAs belowE.A.F. / Con Castcarbon, carbon-manganese 315SlabsSemi-Finished
30, Mira Street162699 Cherepovets
B.O.S and E.A.F Workshops
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 Email: sales@stal.ru Web http://severstal.ruCertificate #: MD00/3821/0003/1 Expiry date: 12/06/2019
Vologda Region
As belowB.O.S. / Con CastSteelmakingPJSC "Magnitogorsk Iron & Steel Works" St. Petersburgcarbon, carbon-manganese 250SlabsSemi-Finished
93, Kirova Street455000 Magnitogorsk
Steel Making and Central Laboratory
Tel +7 351 924 2214 Fax +7 351 924 5879email: kutuev.er@mmk.ru web www.mmk.ruApproval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm.Certificate No. MD00/3103/0005/1 Expiry date: 25/08/2019
A 10Normal StrengthHot Rolled CoilPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel
Rolling Mill 2000Tel +7 351 924 2214 Fax +7 351 924 5879email: kutuev.er@mmk.ru web www.mmk.ruCertificate No. MD00/3834/0003/1 Expiry date: 25/08/2019
A 25Normal StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 25Boiler & Pressure Vessel
Rolling Mill 2350Tel +7 351 924 2214 Fax +7 351 924 5879 email: kutuev.er@mmk.ru web www.mmk.ruCertificate No. MD00/3835/0003/1 Expiry date: 25/08/2019
A 10Normal StrengthHot Rolled CoilPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel
Rolling Mill 2500Tel +7 351 924 2214 Fax +7 351 924 5879email: kuteuv.er@mmk.ru web www.mmk.ruCertificate No. MD00/3836/0003/1 Expiry date: 25/08/2019
A 50Normal StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 40Boiler & Pressure Vessel
Rolling Mill 4500Tel +7 351 924 2214 Fax +7 351 924 5879 emial: kutuev.er@mmk.ru web www.mmk.ruThe approved minimum thickness is 30.0mmCertificate No. MD00/3837/0003/1 Expiry date: 25/08/2019
AH32, AH36, DH32, DH36 50Higher StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg
455000, MagnitogorskRolling Mill 5000
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Certificate No. MD00/4348/0002/1 Expiry date: 24/06/2020
As at 10 April 2018 75Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Serbia
As belowB.O.S. / Con CastSteelmakingHESTEEL SERBIA IRON & STEEL D.O.O. BEOGRAD. BeogradAs below 200SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilA, B, D 15Normal StrengthPlates from coils
Radinac11300 SmederevoTel: +381 26 224 459 email: ODjodjevic@zelsd.rsCertificate No. MD00/0360/0009/1 Expiry date: 15/03/2019
Slovak Republic
A, B, D, E, AH32, AH36, DH32, DH36, EH32,EH36
B.O.S. / Con CastSteelmakingU.S. Steel Kosice, s.r.o. Prague
carbon, carbon-manganese 220Ingots (tonnes)Semi-FinishedA, B 12Normal StrengthPlates360AR, 410AR 12Boiler & Pressure VesselA, B, D 12Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 12Boiler & Pressure Vessel
Vstupny areal U.S. Steel044 54 KosiceTel: +42 55673 4858 Email: mailto: dmalcicka@sk.uss.com Web: http:www.usske.skCertificate No. MD00/1649/0008/1 Expiry date: 16/06/2020
Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximumdimensions 1540mm wide to 12000mm long and thickness as stated.
As belowB.O.S. / Con CastSteelmakingZELEZIARNE PODBREZOVA A.S. Praguecarbon, carbon manganese 280Blooms/BilletsSemi-Finished
Kolkáreñ 35976 81 PodbrezovaTel: +421 48 645 4040 Fax: +421 48 645 4041 email: turis@zelpo.sk web: www.zelpo.sk
Certificate No. MD00/1464/0005/1 Expiry date: 03/12/2019
Slovenia
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingACRONI, d.o.o. Zagrebaustenitic stainlessB.O.S/V.O.D./Con Castcarbon, carbon-manganese, austenitic stainless 250SlabsSemi-FinishedA, B, D, E 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360, 410, 360FG, 410FG, 460FG,490FG, 510FG
40Boiler & Pressure Vessel
304L, 316L, 317L, 321, 347 70Austenitic Stainless
Cesta Borisa Kidrica 44SI - 4270 Jesenice
Member of Slovenian Steel Group
Tel: +385 4 584 1040 Fax: +385 4 584 1068 email: borut.lesnik@acroni.si web: http://sij.acroni.si Certificate No. MD00/1391/0009/1 Expiry date: 24/10/2019
carbon, carbon-manganese, austenitic stainlessE.A.F. / IngotSteelmakingMETAL RAVNE d.o.o. ZagrebA, B 20Normal StrengthSectionsA, B 120Normal StrengthBars
2390 Ravne na KoroškemKoroška cesta 14
Tel: +386 2 870 7200 Fax: +386 2 870 7219 Email: stanko.triglav@metalravne.com Web: http://www.metalravne.comCertificate No. MD00/2889/0006/1 Expiry date: 30/05/2020
As at 10 April 2018 76Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
South Africa
As BelowB.O.S./E.A.F./Con CastSteelmakingARCELORMITTAL SOUTH AFRICA LTD. JohannesburgAs below 240SlabsSemi-FinishedB, D, E 30Normal StrengthPlatesA 50AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
30Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel360AR, 410AR 40LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36
30Ferritic Low Temperature
Delfos BoulevardVanderbijlpark, 1911
Vanderbijlpark Steel
Tel +27 (0)16 889 5146 Fax +27 (0)16 889 5388 email: allan.pass@arcelormittal.com web: www.arcelormittal.com
Certificate No. MD00/1404/0010/1 Expiry date: 06/05/2020
PO Box 2, Vanderbijlpark 1900
Spain
As belowE.A.F. / Con CastSteelmakingACERINOX EUROPA S.A.U. Cadiz304L, 316L, 321, 347 50Austenitic StainlessPlates304L, 316L, 321, 347 20Austenitic StainlessCoil
11379 Los BarriosCadiz
Palmones
Tel: +34 956 629421 Fax: +34 956 629311email: daniel.pinero@acerinox.com web: www.acerinox.com
Certificate No. MD00/0057/0009/1 Expiry date: 14/12/2019
austenitic stainlessE.A.F. / Con CastSteelmakingACEROS INOXIDABLES OLARRA S.A. Bilbao304L, 316L, 321 100Austenitic StainlessBars
Larrabarri, 148150 Larrondo-Loiu
Tel: +34 617 464 872 Fax: +34 944 531 392email: marian.tejedo@olarra.com web: www.olarra.com
Certificate No. MD00/1753/0007/1 Expiry date: 07/09/2018
Vizcaya
As belowE.A.F/A.O.D/IngotSteelmakingACERÍA DE ALAVA, S.A. Bilbaocarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470BloomsSemi-Finished
carbon, carbon-manganese, alloy, austeniticstainless, duplex Stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470Billets
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470Bars
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, ferritic stainless*,martensitic stainless*
360StructuralBars
01470 AmurrioAlava
(ACERALAVA)Poligono Industrial De Saratxo
Tel: +34 94 671 93 00 Fax: +34 94 672 50 62email: carrieta@tubacex.es
* accepted for approved applications.Approval also includes ingots in above grades up to 5 tonne.
Certificate No. MD00/0054/0007/1 Expiry date: 19/01/2019
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELOR MITTAL ESPAÑA Gijoncarbon, carbon-manganese 280SlabsSemi-Finished
Apartado 9033402 Avilés
Factoria de Avilés
Tel: +34 985 187299 Email: mailto:juan-manuel.vigil@arcelormittal.comWeb page http://www.arcelormittal.comCertificate #: MD00/0460/0007/1 Expiry date: 29/08/2017
Asturias
As at 10 April 2018 77Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 80Normal StrengthPlatesARCELOR MITTAL ESPAÑA BilbaoFH27S, FH32, FH36, FH40 25Higher StrengthAH40, DH40, EH40 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80
360FG, 410FG, 460FG, 490FG, 510FG 80Boiler & Pressure Vessel
Apartado 57033200 Gijón
Factoria de Gijón
Tel: +34 985 187299 Fax +34 985 187 519Email: juan-manuel.vigil@arcelormittal.com Web page http://www.arcelormittal.comCertificate No. MD00/1804/0013/1 Expiry date: 23/09/2017
Plates with specified through thickness properties notation Z35 may be added
As belowE.A.F. / Con CastSteelmakingCOMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L. BarcelonaNormal Strength 180BilletsSemi-FinishedA 50Normal StrengthSectionsA 35Normal StrengthBars
Poligono Industrial 'San Vicente' s/n08755 Castellbisbal
C/ Ferralla, 12
Tel: +34 618 695 319 / +34 939 730 400 Fax: +34 93 817 6676 Email: s.cabrenzo@gcelsa.com Web:http://www.celsa.comBillets with nominal 180mm maximum width x nominal 12000mm length to the above maximum thickness Certificate Numberr: MD00/0343/0009/1 Expiry: 20/03/2019
Barcelona
B, D 11Normal StrengthSectionsLAMINADOS LOSAL, S.A. BilbaoA 50DH32, DH36, EH32, EH36, FH32, FH36 11Higher StrengthAH32, AH36 38
Bekoibarra, 9P.O. Box 17
Tel: +34 946251400 Fax: +34 946254976 Mob: +34 68 6942188 email: agonzalez@losal.es / basterrechea@losal.es web: www.losal.esCertificate No. MD00/0993/0011/1 Expiry date: 18/01/2020
48300 - Gernika
As belowE.A.F. / Con CastSteelmakingMEGASIDER ZARAGOZA S.A.U. BilbaoNormal Strength, Higher Strength 130BilletsSemi-FinishedA 15Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 15Higher StrengthA 25Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength
Parque Tecnológico de Reciclado "Lopez Soriano"Ctra. Torrecilla de Valmadrid Km 1.95
Avda. José Lopez Soriano No.100
Tel No: +34 976 466171 Fax No +34 976 517648email: cbilbao@megasa.es web www.megasa.comCertificate No: MD00/4183/0004/1 Expiry date 18/06/2019
B° La Cartuja Baja 50720 Zaragoza
As BelowIF/LF/V.O.D./Con CastSteelmakingRUGUI MELT S.L.U. Bilbaocarbon, carbon-manganese 165BilletsSemi-Finished
Poligono Industrial Emiliano RevillaAvenida de España, n° 21
Tel no: +34 943 85 7311 fax no: +34 943 85 7312Email: iurbieta'rugui.comWeb: www.rugui.comcertificate No: MD00/4352/0001/1 Expiry date 25/06/2017
42110 Olvega (Soria)
A 30Normal StrengthSectionsRUGUI OLVEGA S.L.U BilbaoAH32, AH36, DH32, DH36 30Higher Strength
Avenida de España No. 1,42110 Olvega (Soria),
Poligono Industrial Emiliano Revilla,
Tel: +34 943 8573 11 Fax: +34 943 85 73 12email: sales@rugui.com www.rugui.com
Certificate No. MD00/4435/0001/1 Expiry Date: 25.02.2018
Approval is for wide flats (flat bars) up to a maximum width of 300mm.
As at 10 April 2018 78Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 25Normal StrengthSectionsRUGUI S.L. BilbaoAH32, AH36, DH32, DH36 40Higher Strength
Poligono Industrial Basarte20720 Azcoitia ( Guipuzcoa)
Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:rugui@rugui.com Web http://www.rugui.comThe approved sections are in the form of flat bars up to a maximum width of 200mm. Certificate No. MD00/1915/0007/1 Expiry date: 05/02/2017
Apdo. de Correos no. 8 Azpeitia ( Guipuzcoa)
As belowE.A.F. / Con CastSteelmakingSIDENOR ACEROS ESPECIALES S.L. BilbaoAs below 350BloomsSemi-Finishedcarbon, carbon-manganese, alloy 100MachineryBarsR3, R3S, R4, API-2F, R5 78Chain Cable StockU2, U3 100
Bo. Ugarte, S/NP.O. Box 76
PLANTA DE BASAURI
Tel +34 944 871 726 Fax +34 944 871826 Email: jorge.bas@gerdau.esWeb: www.gerdau.esThe approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasingspecification; MPR3; MPR3S; MPR4; MPR4S ;MPR5.The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate Number: MD00/0051/0010/1 Expiry: 21/01/2018
48970 Basauri (Vizcaya)
As belowE.A.F. / IngotSteelmakingSIDENOR ACEROS ESPECIALES S.L. BilbaoA 220Normal StrengthBarscarbon, carbon-manganese, alloy 230MachineryR3S, R4, API-2F, R4S 185Chain Cable StockR3 203R5 230
Paseo Alejandro Calonje, 139200 Reinosa (Cantabria)
PLANTA DE REINOSA
Tel: +34 942 775 288 Fax: +34 609 242 896 email: borja.lambea@gsidenor com web www.sidenor.com
Certificate Number: MD00/0546/0016/1 Expiry: 18/06/2020
The approval for bars for chain cable stock grades; R3; R3S; R4;R4S; R5 are restricted to supply to Vicinay Sestao to the applicable purchasing specification;MPR3; MPR3S; MPR4; MPR4S; MPR5.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.
The R3 bars with the diameter upto 203mm produced with con cast steel blooms manufactured at Sidenor Aceros Especials Especiales S.L. Planta De Basauri.
The R4 bars with the diameter upto 130mm produced with con cast steel blooms manufactured at Sidenor Aceros Especials Especiales S.L. Planta De Basauri.
The R5 bars with the diameter upto 175mm diameter produced with con cast steel manufactured at Aceros Especials Especiales S.L. Planta De Basauri
The R5 bars with the diameter from 175mm up to 230mm produced from ingot.
carbon, carbon-manganese, alloy 200MachineryBarsSIDENOR ACEROS ESPECIALES S.L. BilbaoR4 117Chain Cable StockR3, R3S 123R5 150U1, U2, U3 152
As at 10 April 2018 79Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Ctra. de Zumárraga, s/n20720 Azcoitia
PLANTA DE AZKOITIA
Tel: +34 943 025206 Fax: +34 943 025299 Mob:+34 647 371 029Email: mailto:juan.aizpuru@gerdau.es Web:http//:www:gerdau.es
The approval for bars for chain cable stock grades; R3; R3S; R4; R5 are restricted to supply to Vicinay Sestao SA to the applicable purchasing specification;MPR3; MPR3S; MPR4, MPR5.
The bars for chain cable stock grades; R3; R3S; R4; R5 are manufactured by con-cast blooms supplieded by Sidenor Aceros Especiales S.L. Planta Basauri; or byingots supplied by Sidenor Aceros Especiales S.L. Planta Reinosa.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.
Certificate Number: MD00/0620/0013/1 Expiry: 26/03/2020
Guipúzcoa
Sweden
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingAB SANDVIK MATERIALS TECHNOLOGY Gothenburgaustenitic stainless, duplex stainlessE.A.F. / Ingotaustenitic stainless, duplex stainless 6Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 265Bloomsaustenitic stainless, duplex Stainless 150Billetsaustenitic stainless, duplex stainless 195austenitic stainless, duplex stainless 185Barsaustenitic stainless, duplex stainless 185StructuralBarsaustenitic stainless, duplex stainless 185Machinery
SE-811 81 SandvikenTel: +46 (0) 26 263311email: erik.k.janssons@sandvik.com web: www.smt.sandvik.comCertificate No. MD00/2173/0007/1 Expiry date: 29/10/2018
Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm long;As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, ForgedProducts
As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS AB Gothenburg304L, 304LN, 316L, 321, 347 13Austenitic Stainless SteelPlates from coilsUNS S31803, UNS S32205*, UNS S32101*, UNSS32304*
8Duplex Stainless
304L, 316L, 321, 347, 304LN 13Austenitic StainlessCoilUNS S31803, UNS S32205, UNS S32101*, UNSS32304*
8Duplex Stainless
Avesta WorksBox 74
Business Area Coil EMEA
Tel: +46 (0)226 810 00 E-mail: johan.nordstrom@outokumpu.com Web: http://www.outokumpu.com*accepted for approved applicationsCertificate No. MD00/0131/0010/1 Expiry date: 06/12/2017
SE-774 22 Avesta
1.4439 2Austenitic StainlessCoilOUTOKUMPU STAINLESS AB Gothenburg304L, 316L, 317L, 321 5UNS S32205, 1.4462, 1.4362* 2Duplex Stainless
SE-64480 TorshällaSpecial Coil Nyby
Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: mikael.paijkull@outokumpu.com Web: www.outokumpu.comCertificate No. MD00/0132/0007/1 Expiry date: 29/01/2019
304L, 304LN, 316L, 316LN, 321 50Austenitic StainlessPlatesOUTOKUMPU STAINLESS AB GothenburgUNS S32304* 10Duplex StainlessUNS S32101* 20UNS S31803(MOD)* 50
As at 10 April 2018 80Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
S-693 81 Degerfors,
BA EuropeDegerfors Operations (QPE),
Tel: +46 586 47623 Mob: +46 70 6565486email: mattias.engvall@outokumpu.com web: www.outokumpu.com
* accepted for approved applications** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.* Avesta 2205, UNS 32205 and EN 10088-1 grade 1.4462 may be accepted as equivalent to UNS 31803 as shown in LR Rules when properties meet the Rulerequirements.
Certificate Number MD00/1754/0009/1 Expiry date: 12/11/2020
UNS S31803, UNS S32205* 200Duplex StainlessBarsOUTOKUMPU STAINLESS AB Gothenburg
SE-693 81 DegerforsDegerfors Long Products
Tel: +46 (0)586 47145 Fax: +46 (0)586 47008email: jorgen.johansson@outokumpu.com web www.outokumpu.com
Certificate number MD00/3144/0007/1 Expiry date: 06/06/2020
* Grades UNS 32205 and EN 10088-1 grade 1.4462 may be accepted as equivalent to UNS 31803 as shown in LR Rules when properties meet the Rulerequirements.
A, B, D, E 50Normal StrengthSectionsOVAKO BAR AB. GothenburgAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
A, B, D, E 45Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
45Higher Strength
Box 559010 Boxholm
Boxholm Works
Tel: +46 (0)240 668062 Fax: +46(0)240 668168 Mobile: +46 (0)70 3769320 Email mailto: thomas.carlsson@ovako.com Web http://www.ovako.com Certificate No. MD00/0560/0010/1 Expiry date: 26/08/2020
As belowE.A.F. / Con CastSteelmakingOVAKO BAR AB. GothenburgA, B, D, E 50Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 50Higher StrengthA, B, D, E 93Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 93Higher Strengthcarbon, carbon-manganese 93Machinery
Smedjebacken WorksS-777 80 SmedjebackenTel. +46 240 668000 Fax +46 (0)240 668168 email thomas.carlsson@ovako.com web www.ovako.comCertificate #: MD00/0561/0007/1 Expiry date: 09/06/2019
As belowE.A.F. / IngotSteelmakingOVAKO SWEDEN AB, BU BAR Hofors-Hällefors Gothenburgcarbon, carbon-manganese, alloy 400BilletsSemi-Finishedcarbon, carbon-manganese, alloy 450Barscarbon, carbon-manganese, alloy 190StructuralBarscarbon, carbon-manganese, alloy 170MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock
Se-813 82 HOFORSTel: +46 (0) 298 25000 Fax: +46 0290 591606 Email: christian.andersson@ovako.com Web: www.ovako.comCertificate No. MD00/1167/0010/1 Expiry date: 26/11/2017
Bars >75mm of grades R3, R3S and R4 supplied for mooring chain cable to Ramnas Bruk AB, Ramnas and Ljusne works. Ovako Grade 316R up to 160mmdiameter approved for R3 mooring chain.
As belowE.A.F. / IngotSteelmakingSCANA STEEL BJÖRNEBORG AB Gothenburgcarbon, carbon-manganese, alloy 75Ingots (tonnes)Semi-Finished
Kristinehamnsvägen 2S-68071 BjörneborgTel: +46 550 251 30 Fax: +46 550 269 5884email: fredrik.gunnberg@cana.no web: www.scana.noIngots as semi-finished products to the above maximum weight; nominal; 2070/2230mm diameter x 2600mm; are approved for further processing for forgings.Certificate Number: MD00/2769/0003/1 Expiry: 03/08/2018
As belowB.O.S. / Con CastSteelmakingSSAB EMEA AB GothenburgAs below 286SlabsSemi-FinishedA, B, D, E 75Normal StrengthPlatesFH27S 40Higher StrengthAH27S, AH32, AH36, AH40, AH42, DH27S,DH32, DH36, DH40, EH27S, EH36
60
DH42, EH32, EH40, EH42, FH32, FH36, FH40,FH42
70
AH46, AH50, AH55, AH62, AH69, DH46, DH50,DH55, DH62, DH69, EH46, EH50, EH55, EH62,
80
As at 10 April 2018 81Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
SwedenEH69, FH46, FH50, FH55, FH62, FH69 80Higher StrengthPlates460FG, 490FG, 510FG 60Boiler & Pressure Vessel360FG, 410FG 75LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40
40Ferritic Low Temperature
S-61380 OxelösundOXELÖSUND
Tel: +46 155 25 58 10
E-mail: per.hofslagare@ssab.com
Website: www.ssab.com
All plates with specified through thickness properties.Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long ofmaximum weight 30T for further processing to rolled products
Materials Quality Scheme Approved - Approval No. MQS 049
Certificate No. MD00/1282/0012/1 Expiry date: 23/04/2020
Taiwan, Republic of China
As belowB.O.S. / Con CastSteelmakingCHINA STEEL CORPORATION KaohsiungNormal strength, Higher Strength 270SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, EH47
75Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50
No.1 Chung Kang RoadHsiao Kang
Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292Email: 54338@mail.csc.com.twWeb page: www.csc.com.tw All grades are approved with specified with through thickness properties.Certificate No. MD00/0304/00013/1 Expiry date: 02/07/2020
Kaohsiung
As belowE.A.F. / Con CastSteelmakingDRAGON STEEL CORPORATION KaohsiungAH32, AH36, DH32, DH36 26Higher StrengthSections
Longjing Dist.,Taichung City
100, Longchang Road,
Tel: +886 4 2630 6088 Ext. 8705 Fax: +886 4 2630 6041 Email:020288@dragonsteel.com.twWeb www.dragonsteel.com.twBillets / Blooms as semi-finished products to the above maximum thickness x nominal 750mm maximum width x nominal 12000mm maximum length Sections produced are H beam sections to the above maximum thickness x 900mm x 300mm overall dimensions x nominal 19000mm maximum length.Certificate Number: MD00/3768/0005/1 Expiry: 01/04/2019
A 15Normal StrengthSectionsT. S. STEEL COMPANY LTD. KaohsiungAH32, AH36 12Higher StrengthA 25Normal StrengthBars
Tsuang-Hine Industrial ZoneHsen-Kang Road
No.6 Kon-Sixth Road
Tel: +886 4 798 0060 Fax: +886 4 799 1522email: fang123@tssteel.com.tw
Certificate No. MD00/2313/0007/1 Expiry date: 09/04/2017
Chang-Hua Hsien
As belowE.A.F. / Con CastSteelmakingTUNG HO STEEL ENTERPRISE CORP. Taipeicarbon, carbon manganese, Normal Strength,Higher Strength
430Blooms/BilletsSemi-Finished
No.22, Pingding Erhu Village,Sihu Township,
Miao Li Works
Tel: +88 637 923333 ext197 Fax: +88 637 922994 Email mailto:h32dkj@tunghosteel.com Web http://www.tunghosteel.comCertifcate Number: MD00/3719/0004/1 Expiry date: 15/12/2018
Miaoli County 36842,
As at 10 April 2018 82Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 18Normal StrengthSectionsTUNG HO STEEL ENTERPRISE CORP. TaipeiAH27S, AH32, AH36 18Higher Strength
No. 8, Jiaxing Street,Xiaogang Dist.
Kaohsiung Works
Tel: +88 6 7802 3131 Fax: +88 6 801 0696 Email: k23@tunghosteel.com Web http://www.tunghosteel.comCertificate Number: MD00/3720/0004/1 Expiry: 14/12/2018
Kaohsiung City, 81257
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingWALSIN LIHWA CORP. Kaohsiungaustenitic stainless, duplex stainless 200SlabsSemi-Finishedaustenitic stainless, duplex stainless 240Billets
Chin Shuei LiYenshui District
Yenshui PlantNo. 3-10, Shi Jou Liau
Tel +886 (0)6 6520911 ext. 5802 Fax +886 (0)6 6520933 Email mailto:eddy_huang@walsin.com Web http://www.walsin.comCertificate No. MD00/3063/0005/1 Expiry date: 14/03/2019
Semi Finished Products Austentic & Duplex Stainless slabs to 1300mm wide, to 12000mm long; square billets to 155mm wide, 12000mm long; round billets withmaximum diameter 240mm , to 12000mm long
Tainan City 73743
Thailand
A 50Normal StrengthPlatesLPN PLATE MILL PUBLIC COMPANY LIMITED Bangkok
Pakklong BangplakodPrasamutjedee
199/9 Moo 4 Suksawad Road
Tel: +66 2815 6400-9 Fax: +66 2815 6415 Email: labtest@lpngroup.co.thWeb: www.lpnpm.co.thCertificate No. MD00/2578/0008/1 Expiry date: 31/08/2020
Samutprakarn 10290
A 40Normal StrengthPlatesSAHAVIRIYA PLATE MILL PUBLIC COMPANYLIMITED
Bangkok
160 Moo 14 Sukhumvit RoadBangpakong
Chachoengsao
Tel: +66 38883 2056 60 Fax: +66 3853 1635 Email: chainarong.t@spm-plate.comWeb: www.spm-plate.comCertificate No. MD00/3952/0003/1 Expiry date: 31/08/2020
Chachoengsao 24130
B, D 8Normal StrengthHot Rolled CoilSAHAVIRIYA STEEL INDUSTRIES PUBLICCOMPANY LIMITED
Bangkok
A 19
360AR, 410AR 19Boiler & Pressure Vessel
9M.7 Tumbol MearumphuengAmphur Bang Saphan
Prachuab Kirikhan
Tel: (+66) 32 691403 Fax: (+66) 32 691408 Email mailto: NavaC@ssi-steel.com Web http://www.ssi-steel.comCertificate No. MD00/3764/0003/1 Expiry date: 22/09/2018
Prachuab Kirikhan 77140
As at 10 April 2018 83Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
The Netherlands
As belowE.A.F. / IngotSteelmakingNEDSTAAL B.V. Haren(Groningen)
carbon, carbon-manganese, alloy 11Ingots (tonnes)Semi-Finished
carbon, carbon-manganese, alloy 320Slabs
carbon, carbon-manganese, alloy 400Blooms
carbon, carbon-manganese, alloy 185Billets
Rapenburg 1NL 2952 AP
Tel: +33 (0) 78 692 3700 Fax: +31 (0) 78 692 3712 Email mailto:h.zuilen@nedstaal.nl & c.gortz@nedstaal.nl Web: http://www.nedstaal.nlThe above semi finished products to the indicated maximum weight/ thickness are approved for further reprocessing for forgings; ingots nominal maximumdimensions 940mm x 780mm x 2300mm long; slabs nominal 620mm wide x nominal 3300mm long; billets nominal 185mm wide x 9200mm long; bloomsnominal 220mm wide x 13100mm long.Certificate Number: MD00/3010/0005/1 Expiry: 10/09/2018
Alblasserdam
As belowB.O.S. / Con CastSteelmakingTATA STEEL IJMUIDEN B.V Haren(Groningen)
carbon, carbon-manganese 225SlabsSemi-Finished
A, B 20Normal StrengthPlates
A, B 20Normal StrengthHot Rolled Coil
Postbus 100001970 CA IJmuiden
IJmuiden Works
Tel +31 2514 92110 Fax +31 2514 70414 Email: jelle.van-der-wal@tatasteel.comweb: www.tatasteel.nlCertificate No. MD00/0698/0009/1 Expiry date: 28/09/2018
Tunisia
A 25Normal StrengthFabricated SectionsPALESCANDOLO CNT sarl GenoaAH32, AH36 25Higher Strength
Parc D' Activite' Economique De Bizerte7000 BizerteTel: + 21 77 241 7292 Fax: +21 77 241 7552 Email: apalescnt@yahoo.fr Certificate Number: MD00/4018/0002/1 Expiry: 25/04/2018
Turkey
As belowE.A.F./Ingot/Con CastSteelmakingASIL CELIK SANAYI VE TICARET A.S. Istanbulcarbon-manganese, alloy 1Ingots (tonnes)Semi-Finishedcarbon 2carbon, carbon-manganese, alloy 600Blooms/Billetscarbon, carbon-manganese, alloy 300StructuralBarscarbon, carbon-manganese, alloy 240Machinery
Gemic Koyu Mevki 16800Orhangazi, BursaTel: +90 224 280 62 60 Fax: +90 224 280 62 00 email bulent.ozmel@asilcelik.com.tr web www.asilcelik.com.trCertificate No. MD00/1921/0007/1 Expiry date: 03/05/2019Machinery bars approved to 220mm diameter from ingot route, and to 240mm diamter from concast route.
As belowB.O.S. / Con CastSteelmakingEREGLI DEMIR VE CELIK FABRIKALARI T.A.S. IstanbulA, B, D, E 60Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
60Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure VesselA, B, D, E 15Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH27S, EH32, EH36,FH27S, FH32, FH36
15Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 15Boiler & Pressure Vessel
As at 10 April 2018 84Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
KDZ. Eregli67330
Tel: +90 (0)372 329 3838 Fax: +90 (0)372 323 2598 email: kaygoren@erdemir.com.tr web: www.erdemir.com.tr
Certificate No. MD00/1951/0011/1 Expiry date: 04/05/2020
Zonguldak
As belowE.A.F. / Con CastSteelmakingÖZKAN DEMIR ÇELIK SANAYI A.S. Istanbulcarbon, carbon manganese 260Blooms/BilletsSemi-FinishedD, E 12Normal StrengthSectionsA, B 25AH40, DH40 19Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
28
Bozköy Köyü13. Cadde N:4 35800
Tel +90 232 625 1515 Fax +90 232 625 1054email: sinan.bektas@ozkansteel.com web: www.ozkansteel.comCertificate No. MD00/2984/0006/1 Expiry date: 25/03/2020
Aliaga-Izmir
Ukraine
As belowE.A.F. / Con CastSteelmakingLIMITED LIABILITY COMPANY METALLURGICALPLANT DNEPROSTEEL
Mykolaiv
carbon, carbon-manganese, alloy 470BarsSemi-Finished
4 Vynokurova Street,49051 Dnipro
DNEPROSTEEL
Tel: +38 067 637 36 48 Fax: +38 056 747 40 40Email: Dmitriy. Chayka@ips.interpipe.bizWeb: www.interpipe.bizCertificate No. MD00/4711/0001/1, Expiry date: 07/08/2020
As belowB.O.S./Ingot/Con CastSteelmakingPJSC "ALCHEVSK IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 300SlabsSemi-FinishedD, E 45Normal StrengthPlatesB 50A 72AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 22Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50360, 410 72A 8Normal StrengthSectionsA 100Normal StrengthBars
Severodonetsk,Lugansk Region,
20A, Vylesova Str.,
Tel: +38 06442 73382email: abrosimov@amk.lg.uaCertificae No: MD00/4588/0001/1 Expiry Date: 26/01/2018
93400
As belowB.O.S. / Con CastSteelmakingPJSC "AZOVSTAL IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 270SlabsSemi-FinishedD, E 50Normal StrengthPlatesA, B 100AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
50Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel
1, Leporsky St.Mariupol 87500Tel: +38 0629 46 8501
E-mail: a.s.sorokin@metinvestholding.com
Website: www.azovstal.metinvestholding.com
Certificate No. MD00/0779/0010/1 Expiry date: 13/02/2021
Including plates with specified through thickness properties. Z35 may be applied to all grades and thicknesses
As at 10 April 2018 85Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / IngotSteelmakingPJSC "ENERGOMASHSPETSSTAL" Mykolaivcarbon, carbon-manganese, alloy 250Ingots (tonnes)Semi-Finished
Donetsk Region84306 Kramatorsk
Tel: +38 (06264) 6-94-93 Fax: +38 (06264) 6-94-93Email: nosenkonina@emss.dn.uaCertificate No. MD00/3575/0002/1 Expiry date: 15/03/2018
As belowB.O.S. / Con CastSteelmakingPJSC "ILYICH IRON AND STEEL WORKS OFMARIUPOL"
Mykolaiv
A, B, D, E 50Normal StrengthPlates
DH40, EH40 25Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50
360AR, 410AR, 460AR 25Boiler & Pressure Vessel
360FG, 410FG 50
1 Levchenko StreetMariupol 87504All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.
Tel: +38 (0)0 629 56 49 79
E-mail: sergey.paramonov@ilyichsteel.com
Website: www.ilyichsteel.metinvestholding.com
Certificate No. MD00/0775/0007/1 Expiry date: 01/07/2019
As belowE.A.F. / IngotSteelmakingPJSC ELEKTROMETALLURGICAL WORKSDNIPROSPETSSTAL
Mykolaiv
304L, 316L, 321 270Austenitic StainlessBars
carbon, carbon-manganese, alloy 300Machinery
U1, U2, U3 85Chain Cable Stock
81 Yuzhnoye ShosseZaporozhye, 69008
named after A.N. Kuzmin
Tel: +38 612 283 4062 email : moroshkin@dss.com.ua web www.dss.com.uaIncluding forged bars and tube blanks (billets) in all above qualities.Certificate No. MD00/2225/0008/1 Expiry date: 02/07/2019
United Kingdom
A 50Normal StrengthSectionsACENTA HOT ROLLED BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
32Higher Strength
A 50Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
Peartree LaneWoodside, Dudley
Tel: +44 (0) 1384 471 200 Email: mailto:ppowell@acentasteel.com Web: http://www.acentasteel.comCertificate Number: MD00/2618/0008/1 Expiry: 19/02/2019
West Midlands DY2 0QS
A, B, D, E 77Normal StrengthSectionsBRITISH STEEL BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36 77Higher Strength
MiddlesboroughTS6 7RP
LACKENBY WORKS
Tel: +44 (0)1642 402789
E-mail: mike.beeson@britishsteel.co.uk
Website: www.britishsteel.co.uk
Materials Quality Scheme Approved - Approval No. MQS031
Certificate No: MD00/0242/0017/1 Expiry date: 31/05/2020
As at 10 April 2018 86Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 20Normal StrengthSectionsBRITISH STEEL BirminghamAH40, DH40 15Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 20
P.O. Box 1Saltburn by the Sea
SPECIAL PROFILES, SKINNINGROVE
Tel: +44 (0)1724 402789
E-mail: claire.sharples@britishsteel.com
Materials Quality Scheme Approved - Approval No. MQS032
Certificate #: MD00/0243/0014/1 Expiry date: 17/08/2020
TS13 4ET
As belowB.O.S. / Con CastSteelmakingBRITISH STEEL Hullcarbon, carbon-manganese 305SlabsSemi-Finishedcarbon 355Blooms/BilletsB, D, E 50Normal StrengthPlatesA 80FH40, FH42, FH46 25Higher StrengthAH40, AH42, AH46, DH40, DH42, DH46, EH40,EH42, EH46
30
FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
70
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 70360, 410 80LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40
30Ferritic Low Temperature
A, B, D, E 50Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
Brigg Road,Scunthorpe.
SCUNTHORPE
Tel: + 44 (0) 1724 402789 Fax: +44 (0) 1724 402936
E-mail: paul2.smith@longsteel.com
Website: britishsteel.co.uk
Materials Quality Scheme Approved - Approval No. 029.
Certificate No. MD00/4619/0002/1 Expiry Date: 09/07/2017
North Lincolnshire DN16 1BP
AH32, AH36, DH32 18Higher StrengthFabricated SectionsCELLBEAM LTD. LiverpoolDH36 30EH46-TM 20High Strength
Thorp Arch Trading Estate Wetherby
Tel: +44 (0)1737 840600 Email: edward.skarret@cellbeam.co.uk Web: www.cellbeam.co.ukCertificate No. MD00/3534/0006/1 Expiry date: 09/11/2020
West Yorkshire LS23 7DB
As belowE.A.F. / Con CastSteelmakingCELSA MANUFACTURING (UK) LTD. SouthamptonNormal Strength 140Blooms/BilletsSemi-FinishedA 25Normal StrengthSections
Seawall Road,Tremorfa,
Sections MillTremorfa Works
Tel: +44 (0) 2920 351899 Fax: +44 (0) 2920 351868
E-mail: gary.jones@celsauk.com
Website: www.celsauk.com
Certificate No. MD00/3552/0004/1 Expiry date: 15/12/2017
Concast blooms/billets covers billets to 140mm x140mm and concast 'mini slabs' to 280 x 120mm.
Cardiff. CF24 5TH
As at 10 April 2018 87Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 12Normal StrengthSectionsLIBERTY MERCHANT BAR PLC. LiverpoolAH32, AH36, DH32, DH36 12Higher StrengthA, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36 50Higher Strength
Scunthorpe Steel WorksBrigg Road,
Liberty House
Tel +44 (0)1724 403094
E-mail: andrew.kennedy@libertyyhg.com
Website: www.liberty.com
The approved sections include flat bar and angled bar
Certificate No. MD00/1599/0011/1 Expiry date: 25/11/2018
Scunthorpe. North Lincolnshire. DN16 1XL
E 50Normal StrengthPlatesLIBERTY STEEL DALZELL LIMITED GlasgowA, B, D 100FH32, FH36 30Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 75
Motherwell ML1 1PUTel: +44 (0)1698 900331
Email to: cheryl.irvine@libertyhg.com
Website: www.libertyhousegroup.com
Certificate No. MD00/0235/0013/1 Expiry date: 17/05/2020
As belowB.O.S./Ingot/Con CastSteelmakingLIBERTY STEEL DALZELL LIMITED Liverpoolcarbon, carbon-manganese 305SlabsSemi-Finishedcarbon, carbon-manganese 355Blooms/BilletsE 50Normal StrengthPlatesB, D 60A 80FH40, FH42, FH46 25Higher StrengthAH40, AH42, AH46, DH40, DH42, DH46, EH40,EH42, EH46
30
FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
70
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 70360, 410 80LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40
30Ferritic Low Temperature
A, B, D, E 50Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
P.O. Box 1Scunthorpe DN16 1BP
Scunthorpe
Tel: +44 1724 404040 Email:maito: shipbuilding@tatasteel.com
Web:http://www.tatasteel.com
All plates with through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS029
Certificate #: MD00/0240/0015/1 Expiry date: 22/07/2017
stainless steelE.A.F/A.O.D/L.A.F/ConCastSteelmakingOUTOKUMPU STAINLESS LTD. Liverpoolstainless steel 19Ingots (tonnes)Semi-Finishedstainless steel 300Slabsstainless steel 300Bloomsstainless steel 200Billets
As at 10 April 2018 88Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
P.O. Box 161Europa Link
LONG PRODUCTS, SMACC
The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitationhardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international ornational standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approvedchemical composition to enables them to achieve the required physical and mechanical properties.
Mass of slab and bloom up to 30.0T.and billet up to 20T
Tel: +44 (0)114 2616292 Mob: +44 7947 255428email: paul.ackroyd@outokumpu.com web: www.outokumpu.comCertificate No. MD00/1883/0009/1 Expiry date: 31/12/2019
Sheffield, S9 1TZ
As belowB.O.S. / Con CastSteelmakingSAHAVIRIYA STEEL INDUSTRIES UK Liverpoolcarbon, carbon-manganese 305SlabsSemi-Finished
Steel HouseRedcar
Tel: +44 01642 408053 Email: david.reevell@ssi-steel.co.uk Web: http://www.ssi-steel.co.uk Certificate No. MD00/4057/0002/1 Expiry date: 21/07/2018
TS10 5QW
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingSHEFFIELD FORGEMASTERS INTERNATIONALLTD.
Birmingham
Brightside LaneSheffield S9 2RW
P.O. Box 286
Tel: +44 (0)114 244 9071 Fax: +44 (0)114 2519021 Email: jbaker@sfel.com
Website: www.sheffieldforgemasters.com
Certificate No. MD00/0524/0009/1 Expiry date: 29/06/2020
A 20Normal StrengthSectionsTATA STEEL UK LIMITED BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
20Higher Strength
carbon, carbon-manganese 20Structural SectionsFabricated Sections
Brenda RoadHartlepool
Hartlepool Works20 Inch H.F.I. Pipe Mill
Tel: +44 (0)1429 527249 Mob: +44 (0)7743 842969 Email: mailto:david.evans@tatsteel.com Web:http://www.tatasteeleurope.com
Certificate #: MD00/0236/0008/1 Expiry date: 09/09/2017
Teeside TS25 2EG
carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingTATA STEEL UK LIMITED BirminghamAs below 13Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 381Semi-finished ProductsBarscarbon, carbon-manganese, alloy 300MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock
StocksbridgeSheffield
Rotherham & Stocksbridge Sites
Tel: +44 (0)114 283 2000 email adam.tilley@tatasteel.com web: www.tatasteelspeciality.com
Certificate No. MD00/1593/0007/1 Expiry date: 03/07/2017
South Yorkshire S36 2JA
As belowB.O.S. / Con CastSteelmakingTATA STEEL UK LIMITED Birminghamcarbon, carbon-manganese 238SlabsSemi-Finished
Port TalbotSA13 2NG
Port Talbot Works
Tel: +44 (0) 1639 872168 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.tatasteeleurope.com
Approval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.
Certificate No.: MD00/3909/0002/1 Expiry Date: 28.04.2017
carbon, carbon-manganese 16Structural SectionsFabricated SectionsTATA STEEL UK LIMITED Birmingham
As at 10 April 2018 89Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
CorbyNorthamptonshire
Corby WorksP.O.Box 101, Weldon Road
Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212 Email: stewart.jeffrey@tatasteel.com Web: http://www.tatasteel.comIncludes fabricated hollow sectionsCertificate No. MD00/0234/0002/1 Expiry date: 25/02/2018
NN17 5UA
United States of America
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BURNS HARBOR ChicagoD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
75Higher Strength
Burns HarborIN 46304-9745
250 West Highway 12
Tel: +1 219 787 2854 Fax: +1 219 787 2139email robert.spangler@arcelormittal.com web: www.arcelormittal.com Certificate Number: MD00/2331/0007/1 Expiry: 16/12/2018
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingELLWOOD QUALITY STEEL COMPANY Philadelphiacarbon, carbon-manganese, alloy 77Ingots (tonnes)Semi-Finished
700 Moravia StreetNew Castle
Tel: +1 724 658 6849 Fax: +1 724 658 6802Email mailto:slubinski@elwd.comWeb: www.egi.orgCertificate No. MD00/2652/0006/1 Expiry date: 14/02/2018
Pennsylvania 16101
A, B, D 50Normal StrengthPlatesEVRAZ OREGON STEEL MILLS SeattleAH27S, AH32, AH36, DH27S, DH32, DH36 30Higher Strength360AR, 410AR, 360FG, 410FG 50Boiler & Pressure VesselA, B, D 19Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 19Higher Strength
14400 N. Rivergate Blvd.Portland
Tel: +1 503 978 6130 Fax: +1 503 978 4975Email: mailto:Christine.wrinkle@evrazincna.com Web http://www.evrazincna.comIncluding normal strength grades with specified through thickness properties (Z35)
MATERIALS QUALITY SCHEME APPROVED - MQS 047Certificate No. MD00/1152/0007/1 Expiry date: 31/05/2018
OR 97203
E 51Normal StrengthPlatesJSW STEEL (USA) INC. HoustonA, B, D 102AH27S, AH32, AH36, DH27S, DH32, DH36,DH40
102Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 102Boiler & Pressure Vessel
5200 East McKinney RoadBaytown
Tel: +1 281 382 5121 email russell.seidenberger@jswsteel.com web: www.jswsteel.us
Certificate No. MD00/3505/0004/1 Expiry date: 24/08/2020
Texas 77523
A, B, D 51Normal StrengthPlatesNUCOR STEEL - HERTFORD COUNTY Norfolk,VAAH32, AH36, DH32, DH36 51Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 51Boiler & Pressure Vessel
CofieldNorth Carolina
1505 River Road
Tel: +1 252 356 3712 E-mail: sales@nucorhertford.com Website: www.nucorhertford.com
Certificate No. MD00/4593/0001/1 Expiry date: 06/07/2019
27922
As belowE.A.F. / Con CastSteelmakingNUCOR STEEL MEMPHIS, INC New OrleansCarbon, Carbon-manganese, Alloy 203Rolled Round BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 511As Cast Round SectionCarbon, Carbon-manganese, Alloy 254Rolled Square Bars
As at 10 April 2018 90Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
MemphisTN 38109
3601 Paul R. Lowry Road
Tel: +1 901 786 5416 Fax: +1 901 788 5300 Email: Gail.Farrow@nucor.com Web http://www.nucor.com
Certificate No. MD00/4059/0001/1 Expiry date: 22/07/2015
As belowE.A.F. / Con CastSteelmakingNUCOR STEEL TUSCALOOSA INC. HoustonA 20Normal StrengthHot Rolled Coil360FG, 410FG 20Boiler & Pressure VesselA 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 13Higher Strength
TuscaloosaAL 35404-1000
1700 Holt Road N.E.
Tel: +1 205 562 1200 Fax: +1 205 556 1482 Email to: jon.miller@nucor.com Web http://www.nucor.com
Materials Quality Scheme approved - MQS048
Certificate No. MD00/3323/0005/1 Expiry date: 04/08/2018
As belowE.A.F./Ingot/Con CastSteelmakingREPUBLIC STEEL Chicagocarbon, carbon-manganese, alloy 14Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 330Bloomscarbon, carbon-manganese 178Billets
2633 Eighth Street N.E.Canton
HOT ROLLED BAR DIVISIONCANTON WORKS
Tel: +1 330 438 5543 Fax: +1 330 438 5552 Email to: DWalvoord@RepublicSteel.com Web: http://www.republicsteel.comIngots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weightshown above.Certificate #: MD00/2236/0006/1 Expiry date: 14/05/2016
Ohio 44704-2311
As belowE.A.F. / Con CastSteelmakingSSAB ALABAMA, INC. New OrleansD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
AxisAlabama 36050
12400 Highway 43 North
Tel: + 01 251 - 6624524
E-mail: Roland.Rufers@ssab.com
Website: www.SSAB.com
Materials Quality Scheme Approved - MQS 042
Certificate No. MD00/3108/0008/1 Expiry date: 29/03/2020
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingSTEEL DYNAMICS INC ClevelandCarbon, Carbon manganese, Alloy 178Rolled BarsSemi-Finished
8000 North County Road 225 East,Pittsboro,
ENGINEERED BAR PRODUCTS DIVISION
Tel: +1 317 892 7179 Fax: +1 317 892 7005
E-mail: Thad.edwards@steeldynamics.com
Certificate No: MD00/4134/0002/1 Expiry Date: 23/03/2019
Concast blooms approved to 262 x 358 mm section.
IN, 46167
As belowE.A.F. / Con CastSteelmakingSTEEL OF WEST VIRGINIA, INC. PhiladelphiaA, B, D 12Normal StrengthSectionsAH32, AH36 12Higher Strength
As at 10 April 2018 91Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
17th Street and 2nd Avenue,Huntington,
Tel: 800-828-6849 Fax: +1 304-697-5842 Mob: +1 304-638-7981
email: jsimmons@swvainc.com web: swvainc.com
Approved for bulb flats
Materials Quality Scheme Approved - Approval No. MQS 059
Cert No: MD00/4547/0001/1 Expiry Date: 31/01/2019
WV 25703
As belowE.A.F./Ingot/Con CastSteelmakingTIMKEN STEEL CORPORATION Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished
CantonOH 44706-0932
Faircrest Steel Plant1835 Dueber Avenue S.W.
Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: robert.w.hoff@timken.com Werb: http://www.timken.com
Certificate No. MD00/1510/0008/1 Expiry date: 10/01/2020
As belowE.A.F. / Con CastSteelmakingTIMKEN STEEL CORPORATION Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished
1835 Dueber Avenue S.W.Canton
Harrison Steel Plant
Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: robert.w.hoff@timken.com Werb: http://www.timken.com
Certificate No. MD00/4284/0004/1 Expiry date: 10/01/2020
OH 44706-0932
As at 10 April 2018 92Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. © Lloyd’s Register Group Limited 2018. All rights reserved.