Quectel Wireless Solutions - Embarcados

transcript

Hands-On Training

Quectel Wireless Solutions

@ Quectel Wireless Solutions | Page 2

EVBs Overview

Qnavigator Tests Guide

GSM EVB & TE-A

GSM EVB – Interfaces Top Side

A: Debug port

B: Main portC: UART3 portD: Adapter interface

E: POWER switchF: VCHG switch (Not used)

G: D/L switchH: PWKEY buttonI: EMERG_OFF button

J: Loudspeaker interface (Not used)K: Earphone interface

L: Handset interface of audio channel 2M: Handset interface of audio channel 1N: Test points

O: Status indication LEDs (D203&D204 Not used)P: 60-pin TE-A interface

Q: Battery interface (Not used)R: Fixture hole for RF cable connectorS: (U)SIM card interface

T: Fixture holes for EVB polesU: Screw holes for fixing the module

V: SD card interface

GSM EVB – Interfaces Bottom Side

D: Adapter interface

L: Handset interface of audio channel 2M: Handset interface of audio channel 1V: SD card interface

GSM EVB - Accessories

UMTS&LTE EVB & TE-A

UMTS&LTE EVB - Interfaces

UMTS&LTE - Accessories

Smart EVB & TE-A

Smart EVB - Interfaces

J702: Headset

J905: GPIOS802: ENG_DownloadS804: Battery Charge

J701: SPIS801: Power Supply Option

S803: ON/OFFJ801: Battery ConnectorS901: Power On Module

J602: Micro USBJ904: GPIO

J601: JTAG

Smart EVB - Accessories

GNSS EVB

EVBs Overview

QNavigator Tests Guide

Step 1: If the tool is installed on Windows 7 or Vista, please first set the Compatibility and

then click Run this program as an administrator before using it.

If it is the first time to use this software,the user guidance would pop up as below. You can

also click ESC button on the keyboard to skip it.

Step 2: Click the Next button to enter the next step.

Step 3: Choose the right module and Click the Next button to enter the next step.

Step 4: QNavigator Main Interface

Step 5: Toolbar

Step 6: UART Configuration

Step 7:

a) Connect to module

b) Check Module Info

c) Check SIM Registration

d) Check SIM Info

Step 8: SMS

a) Insert Receiver number

b) Type of message

c) Message to be sent

d) Send message

e) Read Message

Step 9: Voice Call

a) Number to call

b) Input/Output mode

c) Set Volume

d) Side Tone Gain

Step 10: TCP Connection

a) Set APN data

b) Set Server data

c) Data to be sent to server

d) Data to be received from

server

Note: Use server

IP Address: 220.180.239.212

TCP PORT: 8009

Step 11: UDP Connection

a) Set APN data

b) Set Server data

c) Data to be sent to server

d) Data to be received from

server

Note: Use server

IP Address: 220.180.239.212

UDP PORT: 8012

or http://bit.ly/quectel-udp-server

Step 12: PPP

a) Set APN Configuration

b) Check Network Info

Step 13: QuecLocator

a) Set APN Configuration

b) Check Positiona

Step 14: GNSS

a) Set NMEA Port

b) Check Positioning data

c) Detailed information about

Step 15: General Commands

EVBs Overview

7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui District,

Shanghai 200233, China

Tel: +86-21-5108 6236 Fax: +86-21-5445 3668

Email: info@quectel.com Website: www.quectel.com

Thank you!

www.quectel.com

Quectel Wireless Solutions - Embarcados

Documents