Post on 24-Mar-2022
transcript
SAM HOON Co., Ltd.
Company Introduction
Agenda
About us
Greetings from the CEO
History
Certificate
Organization Chart
Technological Development Status
y
Organization Chart
Flow Chart for Manufacturing
Business Items
Reference Process DiagramReference Process Diagram
About us
General Information
Company Name : SAMHOON Co., Ltd.Company Name : SAMHOON Co., Ltd.
CEO : Mr. Moo. Jong-sam
Address : #577-1 Songnae 2-Dong,Sosa-Gu Buchone-City,Kyunggi-Do, Korea
Tel : +82-32-661-3501~4Fax : +82-32-661-3505Mobil : +82-11-9130-4290 or +82-10-9105-3503
Home Page : http://www.samhoon.com
E-Mail : samhoom@chol.com or tsi2000@chol.com
Greetings from the CEO
Welcome to the Sam Hoon Co., Ltd.
Since the SamHoon Co., Ltd. is founded 1993, we have been in the business of manufacturing quality hollow metal products for the building and construction industry. Specializes in special industrial areas (Special Doors, Blast Proof Doors, Bullet Resistant Door & Windows, Water Tight Doors, Hatch Shield Doors, Gas-Tight Doors, EMP Doors, Air Lock Doors, Automatic Doors, Fire Doors (UL 3/4hr,1hr,1 1/2hr,3hr), Flooding Frevention Facilities, Biological & Chemical Defense Facilities, CBRN Civil Defense evacuation Facilities Protection Materials etc ) forCBRN, Civil Defense evacuation Facilities, Protection Materials, etc.) for prevent national disasters and protect human lives. Our company has the best brains and manufacturing facilities, Quality system ISO 9001, ISO 14001 and UL 10B, UL 63, NFPA 252,CNS11527 ,ANSI A 250.4, EN 1143-1. VII Certification and Industrial property rights that are the foundations of the industry.y
As the company responsible for developing protection facilities in Korea in the 21st century, we have committed ourselves to the technology and quality of our products, in step with the globalization and state-of-the-art technologies within the industry.O i f ff iOur company does not spare even a single drop of effort, and will endeavor to become a world-class company that specializes in related industries.We thank you for your continuous care and attention to our company.
Moo, Jong-sam/CEO
History1 A 10 1993 E t bli h t f SAMHOON CO LTD1. Aug 10, 1993 Establishment of SAMHOON CO.,LTD.
2. Sep 26, 2001 Transferred SAMHOON CO.,LTD. Office to Bucheon City
3. Dec 28, 2001 Acquired ISO 9001 ; 2000 Certification
4 Mar 08 2002 Registered CCK of the 8th United States Army4. Mar 08, 2002 Registered CCK of the 8th United States Army
5. May 12, 2003 Acquisition of a certification of valuation test for Chinese National Standard (CNS 11527)
6. June 26, 2003 Acquired Certification of UL 10B(File No.R21261)-Fire Door (3/hr)
7. June 30, 2003 Acquired Certification of Blast Proof Door (40Bar, 588 psi)A team for high explosive powder, Agency for Defense Development
8. July 30, 2003 Appointed as a Kyeong-gi Internet Trade Frontier Business
9. Oct 14, 2003 Acquired Certification of UL 63(File No.R21544)- with Frame9. Oct 14, 2003 Acquired Certification of UL 63(File No.R21544) with Frame
10. Jan 11, 2004 Vendor Approval for Blast Doors and Window from K.S.C
11. Sep 24, 2004 Registration as material supply company for EXXON MOBILE
12. Jan 05, 2005 Acquired Certification of UL (File No.R21261)-Fire Door (1 1/2hr), q ( ) ( )
13. Jun 29, 2006 Acquire Certification of ISO 14001
14. Jan 31, 2007 Vendor Approval for Blast Doors from YEMGAS(No, YE-001-37-PCC-CNT-54009)
15. Feb 09, 2009 Vendor Approval for Blast Doors from Dubai World Central ppInternational Airport (No, MS-AMB-LAKSHMI-AR-088)
16. July 20, 2009 Acquired Certification of ANSI A 250.4-2001(Lloyd’s Register)
17. Aug 04, 2009 Acquired Certification of EN-1143-1 Level VII(Lloyd’s Register)
Technological Development Status-1
No Technology Item A Standard Authentication Date Project
1 Blast Proof DoorsBlast pressure : 186.2 psi
Air Leakage TestEngineer .W.S.JUNG
1996.04.18~
1996.12.02
ULCHIN Nuclear Power Plant Unit 3&4
2 EPDM Gasket ASTM D 2000Korea Testing and Research Institute for Chemical Industry
1997.09.06~
1997.09.11
ULCHIN Nuclear Power Plant Unit 3&4
3Blast Proof Doors
Air Leakage TestASTM E 283 Korea Institute of
Machinery & Materials1997.09.30~
1997.10.30
ULCHIN Nuclear Power Plant Unit 3&4
Fire Insurers 1999 03 13 YOUNGKWANG4 Fire Door Assembly UL 10 B(3 Hr)
Fire Insurers Laboratories of Korea
1999.03.13~
1999.03.25
YOUNGKWANG Nuclear Power Plant Unit 3&4
5Air Leakage Test for Fire Door
ASTM E 283 CNC1999.06.11~
1999.06.19
YOUNGKWANG Nuclear Power Plant Unit 3&4
6Fire Test for
Bullet resistant DoorsUL 10 B(3 Hr)
Fire Insurers Laboratories of Korea
1999.12.07~
2000.02.06
ULCHIN Nuclear Power Plant Unit 3&4
7 Bullet resistant Doors UL 752 Level 8Agency for Defense
D l t1999.11.07~
2000 02 20
ULCHIN N l P Pl U i 3&4Development 2000.02.20 Nuclear Power Plant Unit 3&4
8Water tight Doors
Roof Hatch Type4.5m Head Water Pressure
2001.04.16~
2001.06.30 SEOUL Subway Station
9Water tight Doors
Swing Left Type4.5m Head Water Pressure
2001.05.20~
2001.08.20 SEOUL Subway Station
10Water tight Doors
Double Left Swing Type
4.5m Head Water Pressure Yeawoo Construction Structure Laboratory
2003.03.28~
2002.04.22 SEOUL Subway Station
11 Test of Blast Proof Doors 40BAR(558 psi)Agency for Defense
Development2002.05.26~
2002.05.30
Agency for
Defense Development
12Water tight Doors
Slide Type Doors1.3m Head Water Pressure
2002.09.04~
2002.11.20 SAMCHUG CITY
13 Blast Proof Doors 60 psi- (Structural Analysis)2002.10.29~
2002.11.15 INDIA ARMY
14 Blast Proof Doors 130psi (Structural Analysis)2002.11.02~
INDIA ARMY14 Blast Proof Doors 130psi- (Structural Analysis)2002.12.15 INDIA ARMY
15Fire Test of Fire Door
With Stainless Fire DoorUL 10 B (3 Hr) UL 2003.01.26 File No. R21261
16Air tight Door
With Stainless Fire DoorsCNS 11527
CTC in
Republic Of China2003.03.22
TAIWAN FOURTH Nuclear Power Plant Unit 1&2
Technological Development Status-2
No Technology Item A Standard Authentication Date Project
17Water Tight Doors
Over Head Type
10.6m Head Water Pressure
(Structural Analysis)
Korea Simulation
Technique.Co.2003.03.28~
2002.04.22 SEOUL Subway Station
18Water Tight Doors 10.6m Head Water Pressure Korea Simulation 2003.03.28~
SEOUL Subway Station18Over Head Type (Water tight Test) Technique.Co. 2002.04.22 SEOUL Subway Station
19Fire Test of Fire Door Frame
With Stainless Fire Door UL 10 B (3 Hr) UL 2003.10.14 File No. R21544
20Fire Test
With Blast Proof WindowBlast pressure : 15 kPa
UL 10 B (1 Hr)Korea Institute of
Construction echnology2004.06.02 Kuwait oil Company(K.S.C)
21Fire Test Blast pressure : 15 kPa Korea Institute of
2004 06 04 Kuwait oil Company(K S C)21With Blast Proof Door UL 10 B (2 Hr) Construction echnology
2004.06.04 Kuwait oil Company(K.S.C)
22 Blast Proof Doors Blastpressure :15&30kPa 2004.10.04 Sakhalin-И LNG in Russian
23 Blast Proof Doors Blast pressure : 25bar Dongyang Co., Ltd.2004.06.04
PAKISTAN ARMY
24 Fire Door Assembly UL 10 B (1 1/2 & 3/4 Hr ) UL 2005.01.05 Exxon Mobil in Sakhalin-І
25Water Tight Doors
Swing Left Type23.0m Head Water Pressure Factory
2006.02.20~
2006.02.23 SMART in Malaysia
26Test of Structure for
Blast Proof Door(13 psi)ASTM E 330 CNC 2008 /06 /25 KRCC
27 Bullet Resistant DoorEN 1522 Class
FB6(Velocity 830+10m/s)
Korea Military
Academy2008 /09 /19 QATAL PEARL GTL
UL 752 Level 8 Korea Military28 Bullet Resistant Door
UL 752 Level 8
(Velocity 838m/s)
Korea Military
Academy2008 /09 /30 QATAL PEARL GTL
29 Frame Anchor Bolt M12 x 123LKorea Testing and
Research Institute2009 /01 /02 GI Type
30 Frame Anchor Bolt M12 x 123L(Stainless Type)Korea Testing and
Research Institute2009 /01 /02 316L Type
31Air Leakage Test
(Slidi D A bl )ASTM E 783 CNC 2009 /03 /16 Expressway YOOSU Tunnel
(Sliding Door Assembly)
32 Hollow Metal Door ANSI A 250.4(Class A) Lloyd’s Register 2009 /07 /20 US Army in Korea
33 Security Door EN-1143-1 Level VII Lloyd’s Register 2009 /08 /04 Central Bank in Iran
Technological Development Status-3
Certificate(ISO 9001, ISO 14001,ANSI A 250.4,EN 1143-1.VII)
Certificate(UL, CNS11527,Blast Door)
Certificate of Blast proof door Certificate of CNS 11527
Certificate(UL, DUNS)
Organization Chart
President
Representativep
Executive Director
Administration Dep’t Production Dep’t Q.C Dep’t
iGeneral Affairs Section
Business Section
MaterialSection
TechnologySection
ProductionSection
QualityAssurance
Section
QualityInspection
Section
Taiwan,Saudi
Arabian,Pakistan.
J.V.C
A/SSection
BusinessSPECIAL DOOR PROJET① Blast Proof Doors② Bullet Resistant Doors③ Water Tight Doors ④ Gas Tight Doors / Air lock Doors⑤ Radiation Shield Doors⑤ Radiation Shield Doors⑥ Roof Hatch Doors⑦ Rolling Metal Doors⑧ Wire Mesh Doors⑨ Hatch Shield Doors
Fire Doors(UL 10B, UL 63) andHollow Metal Doors(ANSI A 250.8, ANSI 250.4)
C.B.R.N Facility Construction Engineering
Construction of Nuclear Power Plants (Special Door)
GATE (Sliding, Cantilever, Hanger Gate, Etc)
Ref. Manufacture Manual : TM5-1300, TM5-858-3
To Put Forward
Blast Proof Door –Army Project
To Put Forward
A. Drawings, Data and Procedures
ⓐ. Certification of Design Report ⓑ. Quality Assurance and Quality Control Programⓒ. Erection Informationⓓ. Detail Shop Drawings ⓓ p gⓔ. Manufacturer's Specificationsⓕ. Shop Welding Methods and Procedure ⓖ. Air Tight Test Procedure (ASTM E 283)ⓗ. Post Weld Heat Treatment Procedureⓘ. Certified Material Test Report (CMTR) ⓙ. Non-Destructive Examination Procedure (NDE)ⓚ. Spare Parts Listpⓛ. Handling, Storage Instruction
B. Quality Verification report and Records Steel Type Blast Door(100Bar)
Blast Sliding Door (U.S.ARMY Kunsan Airport 8th Fleet of USFK)
NCD MCR EntranceINDIA Project(5bar) Magazine Project(100bar) EMBEDD PLATE
Surface outside Surface inside
Blast Proof Door- Nuclear Power Plant
Steel type Blast & Air Leakage Door( Localization of development) / 3 bar
Test on ASTM E 283 Erection of Blast DoorTest on ANSI N510
Air Leakage Test for Nuclear Power Plant Projectfrom Korean Machinery Research Team & CNC
Blast Proof Door –LNG, Oil Project
Russia Sakhalin-II LNG Blast Door(30kPa) Project
Hyundai Oilbank PCD EntranceAuto/Manual Type Blast Door(7PSI &3Bar)
Blast Window : 2.02 psi pressure & 1 hr Fire rateS-OIL NHC Blast Door(7.8psi)
Kuwait Oil : 2.02 psi pressure & 2 Hr Fire rateB-FM PhaseUp-Down Sliding Blast Door(363psi)
Bullet resistant Door (1)
According to UL 752 Level 8 or EN 1522 Class FB6
Bullet resistant Single Door UL 10B(3HR) Fire Tested by - FILK(SINGLE DOOR)
Bullet Resistance Tested by –Korea Military Academy
Bullet resistant Double Door /UL 10B(3HR)
Before Heating After Heating
( )Tested by - FILK(Double Door)
Bullet Resistance Tested by –Korea Military Academy
After heating / 3 hrBefore heating/3 hr
Bullet resistant Door (2)
According to UL 752 Level 8 or EN 1522 Class FB6
ULCHIN NUCLEAR POWER PLANT 3 & 4(MCR)ULCHIN NUCLEAR POWER PLANT 3 & 4(MCR)Range of Bullet-proof : M16-RifleTest Requirement : MIL-STD-662E
We live in a dangerous world. Anything that can make our lives and our property safer and more secure must be given serious consideration. That’s why you-as householder, architect, builder or stockiest-should make more of Laminated Polyglass.yg
Quite simply, Laminated Polyglass is made by forming a sandwich from two, or more, sheets of ordinary, annealed glass bonded together with one or more layers of polyvinyl butyrate plastic to make one permanent transparent piece of glass. It does everything that ordinary glass d l tti i th li ht ff i l
still giving barrier protection against illegal entry and weather penetration.
It provides security. Vandalism, criminal violence and terrorism are on the increase. Laminated Polyglass can be made resistant to every type of attack; from brick to a bomb blast or bullet
gives the architect in particular greater creative design scope.Delivery is fast and prices are truly competitive.
Best of all, you can rely on Laminated Polyglass, whatever your needs, with absolute confidence, every time!
does: letting in the light, offering clearvision and keeping out the weather. But it also offers a host of vital extra advantages.
It provides safety. It takes a pretty heavy impact to penetrate Laminated Polyglass, and if a child or adultwere to run into it or fall accidentally against it causing the glass to break,
bullet.
It provides solar control. That means reduction of solar heat and glare, and protection from ultraviolet radiation which can affect manymaterials.
It provides noise insulation. Noise can annoy or, in some instances, be
iti l h f l L i t d P l lthe broken fragments would stick to the interlayer. There would bevirtually none of the jagged, dangerous splinters that can cause injury.
It provides barrier protection.If broken, the glass remains in fact
positively harmful. Laminated Polyglass is a far more effective insulator than ordinary glass.
Laminated Polyglass is the result ofextensive research and is now available in a range of thickness to suit all end-user needs. It can be produced up to 2500mm wide which
Water Tight Door (1)
Malaysia SMART Project : Pressure of 226 kN/㎠(2.3Kg/㎠)
Subway BULKOAWANG Entrance : Pressure 12.3 ㎠
Frame weldment Door Erection Finish
City Railway Construction, Hyundai Department Store Entrance : Pressure 10.6 Kg/㎠
Water Proof Door (2)
Seoul Subway External EntranceWater level on +4.5Kg/㎠
Ventilation door at Seoul Subway Water level on -4.5Kg/㎠
T W i h Shi ld Sh i h dTemporary Watertight Shield Shower room watertight door
Water tight door (External Entrance )
Gas Tight Door(ASTM E 283)
Korean Nuclear Research CenterAir Leak Rate : 0.0scfm/3.0 psi
CBRN Shelter at 00 projectAir Leak Rate : 0.0scfm/3.0 psi
CBRN shelter at 00 projectAir Leak Rate : 0.0scfm/3.0 psi
Reference of Gas tight Door FrameDistrict office NBC process room
Radiation shield Doors
Door Body Assembly Low wheel Assembly
Air lock DoorAir lock Door
Air Lock DoorAir Leak Rate : 0.0scfm/3.0 psi
Steel Type Door Air Leak Rate : 0.0scfm/3.0 psi
Roof Hatch Door
X : -0.468Y : -0.811Z : 0.350
Dongyang Chemical Goonsan FactoryDriving Type : Air cylinder
Seoul subway ventilation door(608-1) Manual Hydro cylinder Type
Rolling Metal Door
ULCHIN NUCLEAR POWER PLANT 3 & 4 Design Requirement : CP-A2 Driving Type : Auto/Manual
O P R Seoul outer rotation roadShelter hole at Soori, Sooam tunnelsDriving Type : Auto/Manual
ULCHIN NUCLEAR POWER PLANT 3 & 4 Youngdong line Highwayconstruction at Jinbu Tunnel
Wire Mesh Door
ULCHIN NUCLEAR POWER PLANT 3&4
ULCHIN NUCLEARPOWER PLANT 3&4
Parking lot Entrance at Airport
Missile Hatch Shield Door
Design Requirement : CP-A1 Driving Type : Auto/Manual
Heat treatment (Stress relief) Non-Destruction Examination
ULCHIN NUCLEAR POWER PLANT 3 &4(RCB)
Stainless Steel Fire Door (UL 10B,NFPA 80,252)
Fire rate : 3/hr(Fire Test at UL Korea)
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Product Conformance
Conformance to International Specifications and StandardsConformance to International Specifications and Standards
When properly specified, SAMHOON doors and framesWill conform to the document requirements of the internationally recognized agencies listed below.
ANSI A250.4:Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors and HardwareReinforcing
ANSI A250.6:Hardware on Standard Steel Doors(Reinforcement & Application)
ANSI A250.7:Nomenclature: Standard Steel Doors & Frames
ANSI A250.8:Recommanded Specifications for standard Steel Doors and Frames
ANSI A250.10: Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces for Steel Doorsand Frames
ANSI A115:Standard Specifications for Door and Frame Hardware preparation
ANSI A156.7:Standard Template Hinge Dimension
ANSI/NFPA101:Life Safety Code
ANSI/NFPA105:Installation of Smoke and Draft Control Assemblies
ANSI/NFPA80:Fire Doors and Windows
ANSI/NFPA252:Standard Method of Tests of Door Assemblies
BS476 Parts 20 & 22:Fire Test on Bldg. Mtls. and Structures(British)
UL10B:Fire Test of Door Assemblies
UL752:Bullet Resistant EquipmentUL752:Bullet Resistant Equipment
ASTM E 283:Tests of Door Assemblies
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
SAMHOON’s Fire Labeled Steel Doors are 1 3/4”(44.5mm)in thickness and are available in 0.8mm to 2.0mm Stainless steel sheets or steel sheets.Door sinks are mechanically interlocked vertically along the hinge and lock edge.Door edges are beveled 1/8”(3mm)in 2”(50mm) and door surfaces are flush, welded or seams.Door edges are beveled 1/8 (3mm)in 2 (50mm) and door surfaces are flush, welded or seams.All standard doors are manufactured from Galvanized Steel and are prepared and reinforced to receive specified architectural hardware in accordance to ANSI A 115 Standards.
Fire Labels:SAMHOON’s Fire Labeled Steel doors are approved by Underwriters Laboratories(UL).Fire labeled steel doors must be installed with an equivalent fire labeled frame with approved fire listed hardware.For fire labelling restrictions and limitations refer to Fire Labelling Guide for Steel Door.
DOOR LEVEL AVAILABILITY
MODEL TYPE GUAGE DEC MM
LEVEL 1 LIGHT COMMERCIAL
1 Flush 20 0.032 0.8
Handing Type of Door
2 Seamless 20 0.032 0.8
LEVEL 2 HEAVY DUTY COMMERCIAL
1 Flush 18 0.042 1.0
2 Seamless 18 0.042 1.0
LEVEL 3 EXTRA HEAVY DUTY COMMERCIAL
1 Flush 16 0.053 1.3
2 Seamless 16 0.053 1.3
LEVEL 1 LIGHT COMMERCIAL
2 Seamless 14 0.067 1.7
Physical Endurance ( Cycle Testing) Fire Label (Rating)
20 gauge Level C 250,000 cycles
18 gauge Level B 500,000 cycles
T 20 minute
C 3/4 hours
16 gauge Level A 1,000,000 cycles
14 gauge Level A 1,000,000 cycles
O 1 hours
B 1-1/2 hours
A 3 hours
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
HOLLOW METAL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8, ANSI A 250.4)
1) STANDARD DUTY DOOR <Door>Level 2 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>g1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Cerakwool or Polyurethane
Door Design and Fire Labeling Guide for Steel Door (Things in common )
Type Elevation Min. Thk. Max. Normal Door Size (width x high)
Avaiable Rating Note.
Flush1.5mm
Single Lift1214.5mm x 2464mmD bl Lift
1, 1-1/2,2, 3hr
Double Lift2429.0mm x 2464mm
Flush 1.5mm Single Lift1214.5mm x 2464mmDouble Lift2429 0mm x 2464mm
3/4hrGlass area ≤100 sq.in
2429.0mm x 2464mm
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
HOLLOW METAL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8, ANSI A 250.4)
2) HEAVY DUTY DOOR <Door>Level 2 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>Hinge Location1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Cerakwool or Polyurethane
Lock and Hinge Preparation (Things in common )
Mortise Lock Prep. Cylinderical Lock Prep. Hinge Reinforcement
Government Series 86 edgedoor prep is reinforcement
Government Series 161 CylindricalLockset door prep is equipped
3.5mm high frequency hingei f i hdoor prep is reinforcement
with a 1.6mm reinforcement box to help hold mortise lockin proper position in accordanceto ANSI A 115.1 requirements. 2-3/4” backset
Lockset door prep. is equipped with reinforcement and an addedbarrel support spot welded to theedge of the door in accordance toANSlA115.2 requirements. 2-3/4 backset
reinforcement with return bend for added strength.
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
HOLLOW METAL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8, ANSI A 250.4)
3) EXTRA HEAVY DUTY DOOR① Custom construction/seamless
design-rated.② Standard 22gauge vertical steel
<Door>Level 3 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mm
stiffeners for added strength.③ Insulation for thermal and sound
transmission reduction.
Frame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>Hinge Location1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Cerakwool or Polyurethane
Type of Doors (Things in common )
FD GD FG GL LV
Door Profile(Things in common )
DOF Type DOF Type(seamless) Q1F TypeF1F Type
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
HOLLOW METAL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8, ANSI A 250.4)
4) MAXIMUM DUTY DOOR① Custom construction/seamless
design-rated.② Standard 22gauge vertical steel
<Door>Level 4 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 2.0mm
stiffeners for added strength.③ Insulation for thermal and sound
transmission reduction.
Frame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>Hinge Location1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>
Cerakwool or Polyurethane
Cores (Things in common )
Mineral Board Steel Stiffener Honeycomb
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
INSULATED STEEL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Foamed in place polyurethane core provides total surface support, impact resistance and exceptional thermal
resistance.3.Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard Door(ANSI A 250.8)
1) STANDARD DUTY DOOR <Door>Level 2 and Physical Performance Level A, 44.5mmLevel 2 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2 Mortise Lock: 1 7mm(minimum)2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Polyurethane
Type of End Channel (Things in common )Type of Finish (Things in common )
① Stainless steel Finish② Factory - Primer Finish③ Powder Coating④ Galvannealed Steel④ Galvannealed Steel⑤ Hot-Dip Zinc-Coated
Lock Box (Things in common )We can make lock reinforcement acc-ording to customer’s specification with projection welding system as below.
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
INSULATED STEEL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Foamed in place polyurethane core provides total surface support, impact resistance and exceptional thermal
resistance.3.Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8)
2) HEAVY DUTY DOOR <Door>Level 2 and Physical Performance Level A 44 5mmLevel 2 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2 M ti L k 1 7 ( i i )2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Polyurethane
Type of Wall Anchor (Things in common )
PressureAnchor
“Z” Anchor
StrapAnchor
AdjustableAnchor
ExistingMasonryAnchor
MasonryStrap
Anchor
MasonryWireAnchor
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
INSULATED STEEL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Foamed in place polyurethane core provides total surface support, impact resistance and exceptional thermal
resistance.3.Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8)
3) EXTRA HEAVY DUTY DOOR① Custom construction/seamless
<Door>Level 3 and Physical Performance Level A 44 5mm① Custom construction/seamless
design-rated.② Standard 22gauge vertical steel
stiffeners for added strength.③ Insulation for thermal and sound
transmission reduction.
Level 3 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 1.6mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)2 M ti L k 1 7 ( i i )2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core>Polyurethane
Typical Wall Condition (Things in common )
W d Cl d S l S d i h W d S d i hWrap aroundBlock
Wood StudClosed
Steel StudButted Masonry
Steel Stud withGypsum Board
Wood Stud withGypsum Board
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard Comparative Table
INSULATED STEEL DOOR1 Mechanicall interlocked hemmed ertical edge seam for strength and rigidit1. Mechanically interlocked, hemmed vertical edge seam for strength and rigidity.2. Foamed in place polyurethane core provides total surface support, impact resistance and exceptional thermal
resistance.3.Inverted end channels welded to both face sheets for added strength.
ITEM SAMHOON's Standard(DOOR(ANSI A 250.8, ANSI A 250.4)
4) MAXIMUM DUTY DOOR① Custom construction/seamless
<Door>L l 4 d Ph i l P f L l A 44 5① Custom construction/seamless
design-rated.② Standard 22gauge vertical steel
stiffeners for added strength.③ Insulation for thermal and sound
transmission reduction.
Level 4 and Physical Performance Level A, 44.5mmMinimum Steel Thickness/Door FacesDoor Thickness: 2.0mmFrame Thickness: 2.0mm
<Clearances>1.Between Door and Frame: 3.0mm (maximum)2.Bottom of the Frame: 16mm/9.5mm
<Hardware Reinforcing>1. Mortise Hinge Door: 4.5mm(minimum)g ( )2.Mortise Lock: 1.7mm(minimum)
<Hinge Location>1. Top (Rabbet Section Frame to Centerline of Hinge): 298.5mm2. Bottom(Bottom of Frame to Centerline): 330.2mm3. Equally space between top & bottom
<Locks, Latches Locations>1000mm
<Insulation Core><Insulation Core>Polyurethane
Common Types of Jamb Anchor for Per-Set Frame (Things in common )
Pipe Spacer
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Standard FrameSamhoon’s manufactures full range of a Fire Labeled Steel Frames of Standard sizes and profiles to custom sizes and profiles.Steel Frames are available in 1.6mm to 2.0mm for 1 3/4”(44.5mm)doors.All standard frames are manufactured from Electro Galvanized Steel or Stainless steel and are prepared and reinforced to receive specified architectural hardware in accordance to ANSI A 115 Standards.
Welded Corner
Knock Down CornerEasy, quick and sharpmitered corners provide
Welded corners are Ground smooth andprime painted(touched up) to provideA seamless look
Strike Reinforcement1.6mm strike reinforcement suppliedwith closed back eliminating the need toinstall an additional dust or mortar protection
i d t
pfor rapid installation andassembly for a clean uniform appearance.
Hinge Reinforcement3.5mm high frequencyhinge reinforcementwith return bend foradded strength.
Floor Anchor
cover in accordance to ANSlA115.1 reinforcements.
Type ElevationMin.Thk.
Max. Frame Rebate Sizes Notes
Single Double
BasicFrames
2.0mm 48” X 120”(1220mmX3050mm)
96” X 120”(2440mmX3050mm)
For Drywall or Masonry Openings.
Fire Labelling Guide for Steel Frames
Floor Anchor
Available Knock Down or Welded Up
Steel Door and Frame(UL,NFPA 80,252,ANSI A 250.4)
Type of Standard Frame
JAMB DEPTH15MM12MM
SON DON SPN DPN STN DTN
TRANSOM TRANSOM
SOS,SOT DOS,DOT DPS,DPTSPS,SPT STS,STT DTS,DTT
Note: Fist “S” Single “P” Pair Last “S” Stainless Sill “T” Steel Sill
TRANSOM TRANSOM
Note: Fist S Single, P Pair. Last S Stainless Sill, T Steel Sill
15MM Mi 25 t 50MM 15MM Mi 25 t 50MM15MM Min.25 to 50MM 15MM Min.25 to 50MM
DEPTH
RABBETRABBET SOFFIT
BACKBEND
BACKBEND RETURN
STOP
M M
FA
CE
JAM
B D
EP
TH
JAM
B D
EP
TH
THROAT
STANDARD JAMB SIZE STANDARD JAMB SIZE
FRAME COMPONENTS
15M
M
12M
M
Frames Profiles
Fire Door (UL ¾, 1,1 ½, 3 hr,NFPA 80,252)
EXXON MOBIL SAKHALIN-I PROJECT (Fire rate 1 ½ hr)
Type of Fire door
NIGERIA EGP 3 PROJECT (Fire rate 1 ½ hr)
Security Door (EN 1143-1 VII )
Model : SH-2000A (Sliding type) Model : SH-2000M (Sliding type)
Model : SH-880D (Swing type) Model : SH-880 (Swing type) Model : SH-660 (Swing type)
Model : SH-155S (Swing type)
The Other Door(1)The Other Door(1)
IGLOO Shelter Door-Sliding Type Hanger Door of Magazine
Curtain wall and Automatic Door at Ulchin Nuclear
Bulletproof door at Aircraft Shelter
(swing door)
Automatic door pressure operating Equipment
Accordion Gate(Hanjin Marine transport-30m)
The Other Door(2)
Air Leak Door Air Purge Door Buddhist Center Museum
Gas tight door (Dongyang chemical Goonsan factory)
Gas tight door (Dongyang chemical Goonsan factory)
Treasure warehouseSecurity door construction
Digital Door Lock Price
SH 001STANDARD US $252.00
REMOTE CONTROL US $294.00
SH 002STANDARD US $252.00
REMOTE CONTROL US $294.00
SH 003STANDARD US $252.00
REMOTE CONTROL US $294.00
INSIDESH001, SH002, SH003
SH 004US $136.00
SH 005US $136.00
SH 006
US $136.00
SH 007US $136.00US $136.00
INSIDE
SH 009STANDARD US $250.00 SH 008
STANDARD US $250 00SH004, SH005, SH006, SH007 REMOTE CONTROL US $290.00STANDARD US $250.00
REMOTE CONTROL US $290.00
Reference Process Diagram Special Door
1 Drawing 2 Cutting Processing 3 Drilling Processing 4 Milling Processing1.Drawing 2.Cutting Processing 3.Drilling Processing 4.Milling Processing
5.Lathe Processing 6.Inspection 7. Shop Welding 8.Temporary Ass'y
9.Correcting -Temporary Ass'y
10.Blast Sanding 11.Painting 12.Testing
13.Embedment –Installing
14.Door Installing 15.Checking Installing 16.Field Welding
17.Finish
Flow Chart for Manufacturing Special Doors
R i i d iA DWG 접수
Correcting temporary가조립상태 교정
W ldiW/D 작업
Receiving a drawing
Shop designing
SHOP 설계
Approval
승 인도면검토 및 물량산출
1 제작공정수립
Checking Drawing &Estimating raw materials1.Planning manufacturing
process2.Estimating raw materials
g p y
Welding work
WEL DING 작업
assembling
Checking welding andW/D검사 및 GRINDING
grinding
Welding
Checking after welding
W/D작업후 검사
Assembling hardware
HARDWARE 조립
도 장 후 검 사
Ordering raw materials
자 재 발 주
구매 시방서에 승인된 업체
자 재 입 고
종류별 규격별 야적
2.물량산출
1.제작공정수립
Companies approve it thePurchase specifications
Housing raw materials
Unpacking & heaping by kindAnd by size respectively
First Coating
1 차 도 장
작업 및 부재Packing List
NUMBERING
Finishing installation
설 치 완 료
Checking after painting
Making up packing lists andNumbering subsidiarymaterials
자 재 인 수 검 사
재질,규격,치수상태를 판단
공 장 작 업
현도 및 M ki
(분류팻말설치)
외 주 가 공
의뢰
And by size respectively(Installing classification notice board)
Receiving and checking rawmaterialsEvaluating Quality, size andCondition of raw materials
Packing
포 장
Transporting
운 송
현도 및 Marking
Factory Work
Drawing real scales & marking
Inspecting MarkingMarking 검 사
N. C. T 가공의뢰
Processing by the subcontractor
Ordering N.C.T Processing
Inspecting Program프 로 그 램 검 사
D li i d h ki
인 수 검 사
Arriving at the field
현 장 도 착
Temporary assembling
가 조 립
Cutting
절 단
Bending
BENDING
Processing Samples
Sample 가 공
Processing
가 공
Delivering and checking
Installing M/D plates
M/D PLATE 설치
Moving materials into설치장소내 자재반입
The installation place
Inspection
검 사
Temporary assembling
가 조 립
Inspection
검 사
Housing raw materials
자 재 입 고Installing JIG
설치 JIG설치
Checking after installing가설치 후 검사
Door temporarily