Post on 28-Feb-2018
transcript
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
1/13
VISUCAMlite
Fundus Camera
Image Recovery Partition C Recovery
Recovery CDVISUCAM
liteR 1.02
S/N 1242-737
Service Instructions
SM-30-4043-A2-en
Issue: 08.07.2003
Replaces issue: page 1 of 13
Service
Service
Service
Service
MS - TS 1
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
2/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 2 of 13
ContentsPage
Contents .................................................................................................................... 2
Update information................................................................................................... 3
General information.................................................................................................. 4
Image restore Partition restore............................................................................. 5
Overview........................................................................................................................... 5
Transferring an image from CD onto the hard disk....................................................... 5
Erasing the hard disk...................................................................................................... 5
Transferring the new image............................................................................................ 6
Setup English language.................................................................................................. 9
Selective partition transfer from image CD to the hard disk ...................................... 10
Setup English language................................................................................................ 13
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
3/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 3 of 13
Update information
Issue Remarks
08.07.2003 Issue 1
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
4/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 4 of 13
General information
Use the User Manual, SAP No.: 1165-216, as additional literature on the VISUCAMlite
funduscamera. You must be familiar with the contents of the user manual to be able to work with theservice instructions.
The replacement modules have been chosen in such a way that replacing them should bepossible without a special training. If in-depth work on the unit is necessary, you should attendthe appropriate service training.
No fastening components are allocated to and supplied with the spare parts. For this reason,the fastening components provided in the unit must be re-used when modules are replaced.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
5/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 5 of 13
Image recover Partition C recover
Overview
- Image (conplete content of hard disk) recover:
If there is a hard disk installed new in the VISUCAMlite
or a completely down OS (Operating
System) the OS including the VISUCAMlite
program and Database must be transfered ontothe hard disk (Image recover). Is there a used hard disk the partitions have to be erasedbeforehand. If the complete Image is transfered, the complete content of the Hard disk includ thedatabase (patient datas and pictures) will be erased.
- Partition C recover:In case of e.g. crashed OS or an OS Update is necessary only a partition C transfer shouldbe done to the hard disk.Partition C recovery keeps the database (patient datas and pictures) saved on the harddisk.
Note: during this procedure, it is not possible to use the mouse. Buttons can be activated
using the keys or the tabulator key. The Enter key activates or concludes afunction or procedure.
Restoring a complete image from CD-ROM onto the hard disk
Erasing the hard disk
VISUCAM
liteis on.
Insert VISUCAMlite
image CD-ROM intothe CD-ROM drive.
Switch off VISUCAMlite
.
Switch off external CD writer.
Switch on VISUCAM
lite.
VISUCAM liteis booted fromthe CD-ROM and displays the screenshown after some time.
Use the key to perform.
A Pop Up window opens.
Local is highlighted. Use the , key to
highlight Quit.
Use the key to perform.
You are asked for Quit
Use the or tabulator key to highlight
Yes.
Use the key to perform and change toDOS level.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
6/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 6 of 13
DOS level deleting the partitions
Type in cd..
Type in gdisk 1 /del /all
The partitions of the hard drive aredeleted.
Note::German Keyboard!
Key = /
Type in cd ghost
Type in ghostpe
Transferring the new image
The Ghost start up window is displayed
on the screen.
Due to the need of the License
Number later on - write it down
Use the key to perform.
A Pop Up window opens.
Local is highlighted or use the , key tohighlight.
Use the or key to open the nextPop Up window.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
7/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 7 of 13
Disk is highlighted.
Use the or key to open the nextPop Up window.
Use the key to highlight From Image.
Use the key to perform.
A selection window opens.
Use the Tab key to select the input drive(short way: 1 x Shiftand Tab).
The drive window frame is highlighted.
Use the key to open the drive window.
The drive window is opened.
Use the
key to highlight d:the CD-ROMdrive.
Use the key to perform.
The contents of d:is displayed.
Ghostimage:
VCRXXXC.GHO
Ghost imageImage of drive
Version (e.g. 102)
VISUCAM Release
Use the key to set file name
Use the Tab key to select Open Use the key to perform.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
8/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 8 of 13
The Ghost license input window opens.
Input the license number
Use the Tab key to select OK
Use the
key to perform.
The local destination drive is displayed.
Use the Tab key to select OK
Use the key to perform.
The details for the destination drive aredisplayed.
Note:For hard disks with different capacities youcan make changes here.
Use the Tabkey to select OK.
Use the key to perform.
Question for start loading Use the Tabkey to selectYes.
Use the key to perform.
The image is then transferred from theCD-ROM to the hard disk.The bar indicates the progress of the
transfer.
Transfer is finished.
Use the Tabkey to select Continue
Use the key to perform.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
9/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page 9 of 13
A selection window opens
Use the keyto selectQuit.
Use thekey to perform.
A selection window opens to finishGhost
Use the Tab keyto selectYes.
Use thekey to perform.
DOS windows displays
A:\Ghost>
Remove the CD ROM and close the drive.
Switch off the VISUCAM
lite.
Switch on the VISUCAMlite
VISUCAMlite
starts up with German language
Setup English language
Click button Einstellungen
A window Einstellungenopens
Click menu Benutzeroberflche
A menu for user settings opens
Click English for English language.
Restart VISUCAM
liteto perform the new
language setting.
Check all the functions of the VISUCAMlite
and also check all special extra settings:
Finder camera position Printer drivers
Network settings
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
10/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page10 of 13
Recover only partition C from image CD to the hard disk
VISUCAM
liteis on.
Insert VISUCAMlite
image CD-ROM intothe CD-ROM drive.
Switch off VISUCAM lite.
Switch off external CD writer.
Switch on VISUCAMlite
.
VISUCAMlite
is booted fromthe CD-ROM and displays the screenshown after some time.
Use the key to perform.
A Pop Up window opens.
Local is highlighted or use the , key tohighlight.
Use the or key to open the next
Pop Up window.
Use the key to highlight Partition.
Use the or key to open the nextPop Up window.
Use the key to highlight From Image.
Use the key to perform.
a selection window opens.
Use the Tab key to select the input drive.
(short way: 1 x Shiftand Tab)
the drive window frame is highlighted
Use the key to open the drive window.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
11/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page11 of 13
The drive window is opened.
Use the key to highlight d:the CD-ROMdrive
Use the key to perform.
The contents of d:is displayed
Ghostimage:
VCRXXXC.GHO
Ghost imageDrive image
Version (e.g. 102)
VISUCAM Release
Use the key to perform.
The Ghost license input window opens.
Input the license number
Use the key to perform.
The source partitions of the image CDare displayed.
Use the key to select the desired sourcepartition.
Use the key to perform.
The local destination drive is displayed
Use the key to perform.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
12/13
Service instructions Issue: 08.07.2003
SM-30-4043-A2-en Replaces issue: - Page12 of 13
The destination partitions are displayed
Use the key to select the desireddestination partition.
Use the key to perform.
Question for start loading
Use the Tabkey to selectYes.
Use the key to perform.
The partition is then transferred from theCD-ROM to the hard disk.The bar indicates the progress of thetransfer.
Transfer is finished.
Use the Tabkey to select Continue
Use the key to perform.
A selection window opens
Use the keyto selectQuit.
Use thekey to perform.
7/25/2019 SM_30_4043_A2_en_Image Recovery - PartitionRecovery.pdf
13/13
Service instructions Issue: 08.07.2003
A selection window opens to finishGhost
Use the Tab keyto selectYes.
Use thekey to perform.
DOS windows displays
A:\Ghost
Remove the CD ROM and close the drive.
Switch off the VISUCAMlite
.
Switch on the VISUCAM
lite
VISUCAMlite
starts up with German language
Setup English language
Click button Einstellungen
A window Einstellungenopens
Click menu Benutzeroberflche
A menu for user settings opens
Click English for English language.
Restart VISUCAM
liteto perform the new
language setting.
Check all the functions of the VISUCAMlite
and also check all special extra settings:
Finder camera position
Printer drivers
Network settings