Post on 07-Feb-2021
transcript
1 hrs
1 pcs f
0.20 mmk
0.40 mmh PLA
15 g d
MK3/S
SummaryYou can glue a 10 x 1.5 mm round magnet in the base.
Art & Design > 2D Plates & Logos
yoda xwing trooper tie starbird solo sith royal republic ren rebellion r2d2 porg phasma phase order mythosaur maul mandalorian lord kylo jedi han guard first fighter fett emperor death darth clone chewbacca c3po boba alliance luke leia rebels palpatine empire galactic stormtrooper wars vader star
Recommended infill angle: 0°
Low speed and high temperature will create a shiny top surface.
There are "holes" inside the model to make some of the top layers moreuniform, and they were created with 0.2 layer height in mind.
Synth3D
Star Wars X-WingFighter Magnet
VIEW IN BROWSER
updated 14. 6. 2019 | published 12. 4. 2019
https://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnethttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnethttps://www.prusaprinters.org/prints?categoryId=13https://www.prusaprinters.org/prints?categoryId=16##########################################################################################
Print Files (.gcode) DOWNLOAD ALL FILES
2.1 MB
1.23 hrs f 0.20 mm k 0.40 mm h PLA 15.00 g d MK3/S updated 14. 4. 2019
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
1.4 MBupdated 14. 4. 2019
If your top surface is not flat & shiny and you see scarring, then make sureto check this guide: https://bit.ly/2UtN0I1
License This work is licensed under a Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition
x-wing.gcode
x-wing.stl
https://bit.ly/2UtN0I1https://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttp://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/
Star Wars X-Wing Fighter MagnetSummaryPrint Files (.gcode)x-wing.gcode
Model Files (.stl, .3mf, .obj, .amf)x-wing.stl
LicenseAttribution—Noncommercial—Share Alike