Post on 07-Apr-2018
transcript
8/3/2019 Tems Guide
1/11
TEMS 10.X
How to install TEMS 10.X
Once the kit is set up, verify visually that:
To lock W995 UE into specific Band / UARFCN
8/3/2019 Tems Guide
2/11
How to install TEMS 10.Xstep 1: install .net framework 3.5
http://www.microsoft.com/downloads/en/details.aspx?FamilyID=ab99342f-5d1a-413d-
8319-81da479ab0d7&displaylang=en
Step 2: Install TEMS 10.x software.
Step 3: Install UEs driver
- Sony W995 , Samsung A737( QUALCOMM driver)
- PCTEL EX(Scanner)
-GPS (BU303 BU353 GPS Driver)
After installing UEs driver.
http://www.microsoft.com/downloads/en/details.aspx?FamilyID=ab99342f-5d1a-413d-8319-81da479ab0d7&displaylang=enhttp://www.microsoft.com/downloads/en/details.aspx?FamilyID=ab99342f-5d1a-413d-8319-81da479ab0d7&displaylang=enhttp://www.microsoft.com/downloads/en/details.aspx?FamilyID=ab99342f-5d1a-413d-8319-81da479ab0d7&displaylang=enhttp://www.microsoft.com/downloads/en/details.aspx?FamilyID=ab99342f-5d1a-413d-8319-81da479ab0d7&displaylang=en8/3/2019 Tems Guide
3/11
Step 4: Now , Open TEMS Investigation 10.1.2 Data collection. software
And open workspace & command sequence in
particular kit 1/2
-(for TEMS workspace & Command sequence ,please find attached zip
file)
- After importing workspace & command sequence in kit 1 & kit2
look like:
Kit1:
8/3/2019 Tems Guide
4/11
Kit2:
8/3/2019 Tems Guide
5/11
Step 5: Create dial up connection for HSUPA (kit1) & HSDPA(kit2) and
Step6: Now connect HSUPA UE with kit 1 & HSDPA UE with kit2 and check both
HSUPA &HSDPA connection working .
Step7: click on Ctrl &Config tab on TEMS software and connect UEs
Make sure all UEs in proper sequence.
i.e for kit 1: 1. PCTEL (scanner)
2.MT
3. HSUPA
8/3/2019 Tems Guide
6/11
For kit 2: 1. Short MO
2. Long MO
3. HSDPA
4. GPS
Step 8: After all UEs detected and in Proper sequence, click on connect all(F8)
Icon
Step 9: click Overview tab and give logfile Directory(where you want save your log
file)
Path: Command sequence(window)ANY-start RecordingLogfile DirectoryStep10: how to start scanner: Scanner properties for PCTel scanner
8/3/2019 Tems Guide
7/11
Then click on start scanning icon.
Step 11: Now Start to record log file: first start kit1 and then kit2
Once the kit is set up, verify visually that:
1. MO is calling MT. watch it dial, and watch it answer. No assumptions!
2. HSDPA UE is connecting to internet by seeing the world icon displayed on the screen.
And that you are seeing the throughput chart. Also verify that the HSDPA dial interface is
getting connected.
3. Put Long MO on speaker and verify that you are hearing the radio it dials.
4. Check that HSUPA is connecting, performing two sessions, then disconnecting. And thathe sessions are proper.
5. Make sure the proper UARFCN is inputted, and that you are seeing the green bars in the
scanner device
6. Also last and one of the most important items, make sure GPS is tracking and that
you getting the heading while the car is in motion. Every is working except for the GPS,
then all is bad.
To lock W995 UE into specific Band / UARFCN
Please see screeshort:
1
8/3/2019 Tems Guide
8/11
2
8/3/2019 Tems Guide
9/11
3
8/3/2019 Tems Guide
10/11
4
8/3/2019 Tems Guide
11/11
Thanks
Arri