the Roho Group, Inc. - Athome Medical · ENGLISH Section Introduction -3 Section System Components...

transcript

ENGLISH

Section� Introduction �-3

Section� SystemComponents 4-5

Section3 SafetyPrecautions 6

Section4 ImportantSafeguards 7-8

Section5 Installation 9-��

Section6 ManualSetup ��-�3

Section7 Maintenance �4-�5

Section8 CleaningandDisinfecting �6-�8

Section9 Troubleshooting �9-�0

Section�0 SelectAir ��-��

Section�� SelectAirMax �3-�6

Section�� BariSelect �7-3�

Section�3 HybridSelect 3�-34

Section�4 SelectAirProductInformation 35-36

Section�5 Warranty 37

©TheROHOGroup,Inc.�006Thefollowingare trademarksandregisteredtrademarksofTheROHOGroup,Inc.:ROHO®,shapefittingtechnology®,HIGHPROFILE®,SelectAir®,HybridSelect™,HealFloat™,BariSelect™andSelectAirMax™,ELIMSTAPH®,Hi-Tor®,Velcro®andSentinal®areregisteredtrademarksoftheirrespectivecompanies.The ROHO Group, Inc. has a policy of continual product improvement and reserves the right to amendspecificationspresentedinthisbrochure.

Madefor: The ROHO Group, Inc. �00NorthFloridaAvenue,Belleville,IL6��-54�9USA www.therohogroup.com U.S.&Canada:�-800-85�-3449Fax�-888-55�-3449 OutsideU.S.&Canada:�-6�8-�77-9�50Fax�-6�8-�77-65�8

TableofContents

Introduction

SelectAir®lowairlossmattresssystemsarepressurereliefmattresssystemsdesignedforthetreatmentand/orpreventionofpressureulcersandothertissuetrauma,includingburns and other wounds. SelectAir systems are designed to work with any standardhospitalmattressandwillfitonavarietyofdifferentbedframes.

Indications for Use•PressureUlcers •Burns •Geriatrics•Rehabilitation •SpinalCordInjury •Arthritis•Oncology •Orthopedics •SkinFlaps/Grafts•MultipleSclerosis •Neurosurgery •PainManagement•Cardiovascular •PlasticSurgery •Dermatology•AIDS •ExtendedCare •ALS

ATTENTION: ELECTRICAL EQUIPMENT

�. ClassIequipment �. TypeBFequipment 3. Ordinaryequipment 4. ContinuousOperation 5. EnvironmentalConditions: •OperatingLimits: Temperature: 50˚-90˚F(10˚Cto32˚C) Humidity: 80%RHMaximum Altitude: 6,560Ft.(2,000Meters) •StorageLimits: Temperature: 32˚-122˚F(0˚Cto50˚C) Humidity: 80%RHMax.

Section� Introduction

Symbol Legend

Attention- See accompanying instructions for useorinformationfoundinthismanualor labelsonthecontrolunit.

ElectricalHazard

FireorExplosionHazard

Replaceablefuse

On/OffButton

OffOnlyButton

FunctionButton

CPR/EmergencyOffButton

AutoComfortButton

FirmButton

ComfortLevelSettings(Softer,Firmer)

Lock,UnlockButton

PulsateMode

LowSettingButtonforPulsationMode

MediumSettingButtonforPulsationMode(NotavailableontheHybridSelectmodel)

HighSettingButtonforPulsationMode

UprightButton

TypeBFEquipment

TheabovesymbolsareusedonproductlabelingandinthismanualasdefinedbyInternationalElectrotechnicalCommissionorTheROHOGroup,Inc.

SofterFirmer

System Components For Mattress Replacement Models

Section� SystemComponents

Note: SelectAir and SelectAir Max mattress replacements are available indifferentheights,lengthsandwidths.BariSelectisavailableinvariouswidths.

Figure�

WaterResistant,VaporPermeableZipperedMattressCover

Mattress

MattressPad

ControlUnitwithflexiblehoseattached

WaterResistant,VaporPermeableMattressSheet(optional)

System Components For HybridSelect Mattress Overlay Models

Section� SystemComponents

Figure�

MattressOverlay

ControlUnitwithflexiblehoseattached

MattressSheet

ROHOHIGHPROFILECushion

HealFloatSection

Safety Precautions

Pleasereadandthoroughlyunderstandthefollowingsafetyprecautionsbeforeusingthisproduct.

WARNINGS• Explosionriskifusedinthepresenceofflammablesubstances.

• Riskoffire,replacefuseasmarkedoncontrolunit: • Possiblefirehazardwhenusedwithoxygenadministeringequipmentother

thannasalmaskor�/�bedlengthtenttype.Oxygententshallnotextendbelowthemattresssupportlevelorenclosethecontrolunit.

• Electricalshockhazard.Donotremovebackcover.

• Donotuseinthepresenceofsmokingmaterialsoropenflame.Airflowingthroughairmattresswillsupportcombustion.

PRECAUTIONS• Groundingreliabilitycanonlybeachievedwhenthepowercordsupplied withthecontrolunitisconnectedtoanequivalentgroundedreceptacle.

• Unplugthecontrolunitfromthewalloutletbeforecleaning(seeSection8).• Referallservicingtoqualifiedservicepersonnel.

• Formattressoverlays,useasiderailextenderifthetopofthebedrailsarelessthansix(6)inches(15cm)fromthetopofthemattressoverlay.

• The use of bed frame side rails in conjunction with any SelectAir low airloss mattress system should be determined based upon facility protocol,applicable lawsandregulations,and individualusersafetyconsiderations.Bedframesiderailusageisnotarequirementforthefunctionaloperationof any SelectAir product, but individual safety requirements and/or facilityprotocolmaydictatethatsiderailsbeutilized.

Section3 SafetyPrecautions

Important Safeguards

PleasereadandfollowtheinstructionsregardingSelectAirmattressandoverlaysystemsandretainthismanualforfuturereference.Followallwarningsandinstructionsmarkedonthecontrolunitandmattressaswellasthoselistedinthismanual. Note: DONOTplaceliquidsontopofthecontrolunit.

HandlingHandlethecontrolunitwithcare.Droppingitmaycauseinternaldamageandcancausethecontrolunittomalfunction.

Note: DO NOT use a control unit if it appears to be damaged. Consult anauthorizedROHO/SelectAirdistributor.

Dust or DirtKeep the SelectAir control unit away from excessive dust or dirt, which can causeprematurefailure.Thecontrolunit issuppliedwithareplaceableair filter thatshouldbereplacedevery90daysundernormalconditions.Theairfiltershouldbeinspectedandcleanedeverymonthundernormalconditions,andmorefrequentlywhenusedinabnormallydustyordirtyenvironments.

CleaningUnplug the control unit from the wall outlet before cleaning. Do not use harsh liquidchemicals, cleaning solvents or aerosol cleaners. Water and a mild dish washingdetergentmaybeusedonasoft,dampclothorpapertowel.PleaserefertoSection8.

AccessoriesDonotplacethecontrolunitonanunstablesurfacebecauseitmayfall,causingseveredamage to the control unit. Use only manufacturer-recommended accessories.Anymountingof thecontrolunitmust followthemanufacturer’s instructions.Thehospitalbedfootboardmustbeabletosupportthecontrolunitandanyadditionalweight.

Heat and VentilationRefer topage�of thismanual foroperatingandstorage limits. It is important thatthisopening isnotblockedor coveredduringoperation.Thecontrolunit shouldnotbeplacedinabuilt-ininstallation,suchasaclosetorrackunlessproperventilationisprovided.

Power SourcesThecontrolunitshouldonlybeoperatedfromanappropriateACoutletcapableofsafelydeliveringatleastthree(3)ampsofelectricalcurrent.Ifyouarenotsureofthetypeofpowersupplyavailable,consultyourROHO/SelectAirdistributororacertifiedelectrician.

Object Entry and Excess WeightNeverpushobjectsofanykindintothisproduct.Excessweightplacedonthecontrolunitcancausedamagetothehousing.

Grounded Power Cord and PlugThiscontrolunitisequippedwithagroundedpowercord.Theplugwillfitintothepoweroutletonlyoneway.Ifyouareunabletoinserttheplugfullyintotheoutlet,contactyour

Section4 ImportantSafeguards

ROHO/SelectAirdistributorpriortooperatingthecontrolunit.Donotaltertheplugtofitintothepoweroutlet.Thepowersupplycordshouldberoutedsoitwillnotbewalkedonorpinchedbyitemsplaceduponitoragainstit.

OverloadingOverloadingwalloutletscanresultinariskoffireorelectricshock.Asinglegroundedextensioncord (threewireswithgroundedplugs)of less than25 feet (7.6meters) inlengthandwithaminimumofa�5ampratingcanbeusedwiththecontrolunit.

ServicingDonotattempttoservicethiscontrolunityourself.Openingorremovingthecovermayexposeyoutohazardousvoltages.ReferallservicingtoyourROHO/SelectAirdistributor.Breakingorremovingcalibrationsealsvoidsthewarrantyofthecontrolunit.

Mattress StorageCleananddisinfectproductasperthisoperationmanualandstoreinadryenvironmentatroomtemperature.

Replacement PartsWhenreplacementpartsarerequired,besure that thecontrolunitusesreplacementpartsfromthemanufacturer.Unauthorizedsubstitutionswillvoidthewarranty.

Safety CheckUpon completion of any service to this product, the ROHO/SelectAir distributor mustperformsafetycheckstodeterminethattheproductisinasafeoperatingcondition.

Interference Thecontrolunitisdesignedtopreventradiationofradio-frequencyenergy.Thereisnoguarantee thatcommunicationsorother radio-frequency interferencewillnotoccur inaparticular installation. If thiscontrolunitdoescauseharmful interference to radioortelevision reception, which can be determined by turning the control unit off and on,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingsteps:

• Makesureelectricalcordisproperlygrounded.• Relocatethereceivingantennaofthedeviceaffected.• Increasetheseparationbetweenthecontrolunitandthedeviceaffected.• Connectthecontrolunittoanoutletthatisonadifferentcircuitthanthedevicebeing

affected.

Section4 ImportantSafeguards

Section5 Installation

Installation-Mattress ReplacementsMattress

Note: Makesurethatthemattresshosefittingisatthefootendofthe bedframe.

A. When using the Mattress Cover with Mattress Replacement: Whilethemattressisinflating,itmaybehelpfultopartiallyunzipthecoverand guidethemattressintothecorrectformation.

�. Alwaysremovetheexistingmattressfromthebed.

�. Beforeplacingmattress insidemattresscover,ensure thatall foursidebolsterstraps(twoperside)aresecuringsidebolsterstomattresssectionsandVelcro®fastenersaremated.

3.Insertthemattressandmattresspadinsidethemattresscoverandzipthecovershut.Placeon thebed frame.Besure thehole in themattresscover is in thecorrectpositiontofitaroundthehosefittingoutletonthemattress.

4. Strapthecovertothebedframeusingthefourstrapslocatedoneachsideofthemattresscover.

B. When using the Mattress Cover and the Mattress Sheet with Mattress Replacement:

�.Alwaysremovetheexistingmattressfromthebed.

�.Beforeplacingmattress insidemattresscover,ensure thatall foursidebolsterstraps(twoperside)aresecuringsidebolsterstomattresssectionsandVelcro®fastenersaremated.

3. Insertthemattressandmattresspadinsidethemattresscoverandzipthecovershut.Placeon thebed frame.Besure thehole in themattresscover is in thecorrectpositiontofitaroundthehosefittingoutletonthemattress.

4.Strapthecovertothebedframeusingthefourstrapslocatedoneachsideofthemattresscover.

5.Fitthemattresssheetoverthecoveredmattressandattachthestrapstothebedframe.

Installation-Overlay Models

Mattress Overlay Note: Makesurethatthemattresshosefittingisatthefootendofthe

bedframe.

A. Mattress Overlay Instructions

�.Placethemattressoverlayontopoftheexistingmattress.

�.Inserthoseintothefootsectionofthemattressoverlay.

3.InserttheROHOHIGHPROFILEcushionintothecushioncover.

4.PlacetheROHOHIGHPROFILEcushionintotheHealFloatfootsectionof themattressoverlay.

Note: Refertothecushion'senclosedoperatinginstructionsforpropersetup andadjustment.

5.Afterinflatingthemattressoverlay,securethemattresssheettothemattress.

6.RemovetheROHOHIGHPROFILEcushionandplaceonchairtoprovide continuedskinprotectionwhilepatientisseatedinachair.Readjustthecushion forthepatientaccordingtothecushion'sinstructions.

Control Unit-All Models

�. Place the control unit handle over theedge of the footboard. The handle willselfadjust to thewidthof the footboard(fig.3).

�. Insert the hose fitting with the clip intotheairoutletofthecontrolunitandturn�/4turn.Ensurethehosefittingisfirmlyseated and that the latch ‘clicks’ intoplace(fig.4).

3. Inserttheotherendofthehoseintothemattresshosefittinglocatedatthefootofthemattress(fig.4).

Figure4

Figure3

4. Ensurethepowerentryswitchis“OFF”.

5. Firmlyinsertthepowercordintotheoutletonthecontrolunit(fig.6).

6. Insert the other end of the power cord into an equivalent grounded powerreceptacle.

7. Pressthepowerentryswitch“ON”andrefertoManualSetup(Section6).

Note: Checktomakesureallhoseconnectionsaresecurebeforeturningon.

Manual Setup

�. Pressthe“On/Off”buttononthekeypadtothe“On”positionandallowthemattressto FULLY inflate before making any adjustments or placing the patient on themattress.

On OffFigure5

Section7 ManualSetup

SelectAir,SelectAirMax,

HybridSelectModels

Figure8

ON/OFF

BariSelectModelsonly

Figure6 Figure7

PowerEntrySwitch

FuseCompartment

PowerEntryReceptacle

15feet(4.6meters)

��

�. Pressthefirmmattresstimer.

3. Placethepatientonthemattress,centeredandintheirhabitualrestingposition,i.e.ontheirback,ontheirside,etc.

CAUTION: Thebedrailsshouldbelockedintheirhighestposition beforeproceeding.

4. PresstheFirmMattress“OFF”buttonifilluminated.

5. Determine the patient’s weight and set the Comfort Level using the ComfortLevel “Softer” and “Firmer” buttons to the matching information on the ComfortLevelChart(pg.13).Seesection12forinstructionsonhowtomanuallyinputthepatient'sweightontheBariSelectmodel.

Note: Due to the different shapes and sizes of each patient, the settingsrecommended on the Comfort Level Chart are only a guideline. UserjudgementmustbeappliedtoproperlyadjusttheComfortLeveltothesettingthatbestsuitsthepatient.

6. Allow air in themattress to equalize for aminimum of two (2)minutes beforeproceeding.

Figure9A SelectAir,SelectAirMax,

HybridSelectModels

BariSelectModels

Figure9BBariSelect

Modelsonly

HybridSelectModels

SelectAirSelectAirMax

Models

Figure�0

HybridSelectModelsonly

BariSelectModels

Comfort Level

��

Comfort Level Reference Chart Note: Thesechartsareonlyaguidelinebecauseweightdistributionvaries frompatienttopatient.

9. Followfacilityprotocol,applicablelawsandregulations,andindividualusersafetyconsiderationsforusageofbedframesiderails.

7. Checktoensurethatthepatienthasimmersedintothemattressabout40–50%.Iftheyhavenot,adjusttheComfortLevelusingtheComfortLevel“Softer”and“Firmer”buttonsandrepeatsteps6and7untiltheproperresultsareachieved.

8. Once the desired setting is found, check to see if there is adequate clearancebetweenthepatientandthebedframebyplacingyourhandbetweenthepatientandthebedframe.Thereshouldbe3-4inches(7-10cm)ofclearance,andthepatientshouldnotbetouchingthebedframeatanypoint.AdjusttheComfortLevelsettinguntiltheproperresultsareachieved.

{75 34 3.5-4�00 45 4��5 57 4-5�50 68 5�75 79 5-6�00 9� 6-7�50 ��3 7-8300 �46 8-9350 �59 9400 �8� �0

(Kilograms)Setting

(ComfortLevel)Patient Weight

(Pounds)

SelectAirSelectAirMax

WeightRanges

�00 45 ��50 68 ��00 9� 3�50 ��3 4300 �46 5

{(Kilograms)

Setting (ComfortLevel)

Patient Weight (Pounds)

HybridSelectWeightRanges

{300 �46 6350 �59 7400 �8� 8450 �04 9500 ��7 �0550 �49 ��600 �7� ��650 �95 �3680 308 �3.5

BariSelectWeightRanges

(Kilograms)Setting

(ComfortLevel)Patient Weight

(Pounds)

Note:Beforeopening,observewhatvoltageisvisibleontheredfuseholder throughthewindowonthefuseholderdoor.

4.Carefullyremovetheredfuseholdertoaccessthefuse.

5.Checkfusewithacontinuitytester.

6.Replacebadfusewiththecorrectversionlistedontheinformationlabel.

7.Replacetheredfuseholderinthepowerentrymodule.

8.Closethefuseholderdoorensuringthecorrectvoltageappearswhenthedoorisclosed.

9.Plugthelinecordintothepowerentrymoduleandplugtheotherendintoanappropriategroundedoutlet.

�0.Theunitisnowreadytoresumenormaloperation.

Section7 Maintenance

Maintenance

Control UnitsAll control units are designed to be virtually maintenance free. The only servicingrequirediscleaningofthehousingandchangingthefilter.

Note: Thecontrolunitcontainsnootheruserserviceablepartsanditshouldonlybeopenedbyqualifiedservicepersonnel.

Fuse DANGER: THEFUSEMUSTONLYBEREPLACEDWITHTHE PROPERFUSEASLISTEDONTHEINFORMATION LABEL.DONOTREPLACETHEFUSEWITHONE OFHIGHERVALUEOROFDIFFERENTTYPE.

Toreplacethefuse:

�.Turnoffthemainpowerswitchonthepowerentrymodule,locatedontheleftsideoftheunit.

�.Unplugthelinecordfromthewallsocket,removetheotherendfromthepowerentrymodule,andsetaside.

3.Insertasmallflatscrewdriverintotheslotlocatedatthetopofthepowerentrymoduleandcarefullyopenthefuseholderdoor.

Filter

Thefiltershouldbeinspectedandcleanedeverymonthundernormalconditions.Inspectfilterandcleanorreplaceasnecessary.Bariatricpatientsgenerallyrequirehigherairpressureforsupport,therefore,theairfiltershouldbeinspectedandreplacedmorefrequently.

Tocheckandchangethefilter:

�. Firmlypull forwardandthendownonthefiltertray located at the front of the control unit.Thefiltertraywillautomaticallystopinthefullyopenedposition(fig.11).It isnotnecessarytocompletelyremovethefiltertray.

Important: Keepthefiltercleanandtheairopeningclearofobstacles.

2. Remove the filter from the filter tray (Fig. 12)by grabbing the filter by its edges andinspecttheconditionofthefilter.

Ifdirty,washthefilterinamilddetergent.Let the filter dry completely beforereplacingthefilterbackintothefiltertray.If the filter is torn or in bad condition,replaceitwithanewone.

Note: Donotusethecontrolunitwithoutafilter.

3. Replacethefilterbyfirmlypressingthefilterinaroundtheedgesinthefiltertray.

4. Ensurethefilterislayingflatandpushthefiltertrayupintothehousing.

HealFloat Feature (HybridSelect only)ToproperlymaintaintheROHOHIGHPROFILECushionintheHealFloatfeature,refertothecushion'soperationmanual.

Section7 Maintenance

Figure��

FilterTrayandFilter

FilterTray

Filter

Figure��

Cleaning and Disinfecting

Note: Thefollowinginstructionsareintendedonlyasgeneralguidelines.Followyourfacility’sstandardprotocolforcleaninganddisinfectingmedicalequipment.IfyouhaveanyquestionscontactyourROHO/SelectAirrepresentativeorTheROHOGroupCustomerServiceDepartment.

Mattress/Overlay (during use)Cleanwithamilddetergentandadampcloth.Donotuseharshchemicals,alcohol,orsolvents.Wipedry.Theairmattressshouldbeinflatedwhilecleaning.

Note: Donotheatorsteamclean.Toassuresafetyfrominfection,completelydisinfectallbeddingusingthepropercleaningrecommendations.

Mattress/Mattress Overlay (between patients)Theairmattressormattressoverlaymustbethoroughlycleanedbetweenpatients.Topreventmoisturefromenteringthemattress,keepthemattressinflatedthroughoutthecleaningprocess.

�. Withthemattressoroverlayinflated,spraytheentiremattresswithbleachdiluted�:�0bleachtowater.

�. Allowbleachtoremainonmattressoroverlayforamaximumof�0minutes.3. Rinsethemattressoroverlaywithfreshwater.4. Spray surface with a disinfectant. ROHO recommends using LpHse® diluted

�:�56.5. Allowsolutiontoremainonmattressoroverlayforamaximumof�0minutes.6. Brushsoiledareasandrinsewithfreshwater.7. Allowair flowtocontinuethroughthemattressoroverlay for�0minutesafter

completion of cleaning procedure to prevent any moisture from entering themattress'oroverlay'sairholes.

8. Hangtodry.9. Spraysurfacewithaquaternaryammoniumcompoundmixedasa�%solution

inwater.ROHOrecommendsusingCalgonVestalLaboratoriesCoverageSprayDisinfectantCleaner®.

Mattress Pad (between patients)�. Spraypadwithadisinfectantusinghighpressurespray. ROHOrecommends

usingLpHse®diluted�:�56.�. Allowsolutiontoremainonpadfor�0minutes.3. Brushallsoiledareasandrinsewithfreshwater.4. Hangtodry.

Mattress Sheet for Mattress or Mattress Overlay (between patients)�. Presoakthesheetinadisinfectantfor�0minutes.ROHOrecommendsusing

LpHse®diluted�:�56.�. Remove the sheet from the presoaked disinfectant and place in a standard

agitator type washing machine. Take care not to overload the washingmachine.

3. Thoroughlyremovethedisinfectantfromthesheetbyusingtwofullregularwash/rinsecyclesofthewashingmachinewithoutanylaundrydetergentadded.The

Section8 CleaningandDisinfecting

washingmachineshouldbesetataregularwash,hotwatersetting.4. Launder thesheet inanormalmannerusing the regularcycleandhotwater

washsettingofthewashingmachine.Useastandardlaundrydetergentasthelaunderingagent.Makesurethatafullclearrinsecyclefollowsthewashcycletoremoveallthecleaningsolutionresidues.

5.Drythesheetinastandardclothesdryersetatlowheat(DelicateFabrics)settingfor7-�0minutes.

6.Afterdrying,thesheetmayberepackagedandreturnedtocleaninventory.

Zippered Mattress Cover (during use)

�. Wipesurfacewithneutralsoapandlukewarmwater. �. Rinsewithwateranddry.

Zippered Mattress Cover (between patients)

Note: Donotcleanwithaphenolic-basedcleaningsolutionasitwilldamagethe urethane coating on the cover’s nylon fabric. These instructionsmustbefollowedtomaintainthequalityandintegrityofthematerial.

�. Deflateandremovethemattressfromthemattresscover.�. Place the mattress cover in a standard agitator-type washing machine. Take

care not to overload the washing machine. You may presoak the cover in aquaternary solution (disinfectant) diluted with water. We recommend usingSentinal,ElimstaphorHi-Torsolutionsdiluted�:�56.

Note:Washinwarmwater[notwarmerthan140°F(60°C)].Donotuse bleach.

3. Afterpresoakingcycle isover, thewashingmachineshouldbesetondelicatefabricsorpermanentpresscycle.

Note:Washinwarmwater[notwarmerthan140°F(60°C)].Donotuse bleach.

4. Toremoveanyremainingdisinfectant,washmattresscoverondelicatefabricsorpermanentpresscycle.UseastandardlaundrydetergentwithNObleach.Washonecycleusingthelaundrydetergent.

Note: Usecoldwateronly.Donotusebleach.5. Drythecoverinastandardclothesdryersetondelicatecyclewithalowheat

setting.TUMBLEDRYONLY. Note:Donotusehighheat!6. After drying, the mattress cover may be repackaged and returned to clean

inventory.

HealFloat feature (HybridSelect only)Refer to theROHOHIGHPROFILEcushion’soperatingmanual forspecificcleaninginstructions.

Control Unit and Hose (between patients)�. Unplugthecontrolunitfromthewalloutletbeforeproceeding.�. Wipedownentirecontrolunitandallhoseswithadisinfectantsolution.ROHO

recommendsusingLpHse®diluted�:�56.3. Allowsolutiontoremainonsystemfor�0minutes.4. Wipedownentirecontrolunitanddrywithdisposablecleaningclothorsponge.5. Onlyuseamilddetergent(dishwashing)andwarmwatertocleanthefilter.Rinse

thefilterwithcoolwaterandthoroughlyairdrythefilterbeforereplacing.

All Control Units

DANGER: Disconnectcontrolunitfrommainpowersupplybeforecleaning.Failuretodosocouldresultinelectricshock.

Note: •Donotimmersethecontrolunitinliquids. •Donotheatorsteamautoclavethecontrolunit.

Note: Donotsaturatethesurfaceofthecontrolunitwithliquids.Wipeoff any dust. If necessary, clean the housing exterior with adisinfectantsolutionormilddetergentandadampcloth.Wipedry.

DANGER: Makesurethecontrolunitiscompletelydrybeforeattemptingtoreconnectoroperateit.

Troubleshooting

Problem/Corrective Action1. Control unit does not function, and power light not illuminated.

Ensurethepowercordisconnectedtoafunctioningpoweroutletsupplyingvoltageindicatedonthecontrolunitlabel.EnsurethatpowercordisfullyinsertedintothepowerinletreceptacleonthesideoftheControlunit.Ensurethepowerswitchonthepowerentryreceptacleisswitchedtothe“On”position(switchedmarked“-/0”,depress“-”toturnon).Ifaboveconditionsareverified,checkthecontrolunitpowerfuseinthepowerinletreceptacle.Seethe“Maintenance”sectionofthismanualforinstructionsonchecking/changingthefuse.If,afterreplacement,thefuseblowsagainwhenpowerisapplied,removetheunitfromserviceandcontactyourROHO/SelectAirDistributorforassistance.

2. Control Unit does not function. Power and all comfort level light flash alternately, unit sounds single repeating beep.

CPRShutdownactivated.Turnpowerswitchonsideofunitofffor�0secondsandbackontoresumenormaloperation.

3. Control Unit does not function. Power and comfort level lights 1 and 10 flash alternately, unit sounds single repeating beep.

Hose-lossalarmtriggered.Ensurehoseconnectionsatcontrolunitandmattressaresecured,turnpowerswitchonsideofunitofffor�0secondsandbackontoresumenormaloperation.Ifalarmtriggersagainafterabovesteps,checkmattressforlargeairleaks.

4. Control Unit does not function. Power light flashes and unit sounds double repeating beep.

Powerlossalarmtriggered.Ensurethepowercordisconnectedtoafunctioningpoweroutletsupplyingvoltageindicatedonthecontrolunitlabel.Ensurethatpowercordisfullyinsertedintothepowerinletreceptacleonthesideofthecontrolunit.Presspowerbuttononfrontpaneltoresumenormaloperation.

5. Control Unit appears to function normally, but mattress does not inflate.

••

Section9 Troubleshooting

Checkhoseforcrushedorkinkedareas,orinternalblockages.Removefiltertrayandensureairinletventincontrolunitisfreeofobstruction.Ensurethatmattressisnottwistedorfoldedathoseconnection.Checkcomfortlevelsettingofcontrolunit.Lowsettingmaycausesomesectionsofthemattresstoinflateveryslowly.

6. Control Unit appears to function normally, but is abnormally warm.Someareasofthecontrolunitcasewillbecomeslightlywarmduringnormaloperation.Ifinquestion,comparetemperaturetoanotherunitoperatinginthesameconditionsandatthesamecomfortlevel.

Ensurethatairinletfilterisnotcloggedorobstructed.EnsurethatControlUnitairinletisnotblockedorobstructedbybeddingorothermaterials.Ensurethattherearenokinksorobstructionsinhosetomattress.Ensurethatambienttemperatureisnotabove90°F(32°C).Ensurethatthecontrolunitisnotbeingusedatanaltitudeexceeding6560feet(2000meters)Ensurethatthemattressisbeingusedwiththecorrectcoverand/orsheet.Airmustbeallowedtoescapefromtheair-lossholesinthetopsurfaceoftheinnermattressforproperfunction.

7. Control Unit runs, but does not respond to keypad entries.Ensureoperatingenvironmenttemperatureisnotbelow50°F(10°C).Allowcontrolunitto warmtoroomtemperaturebeforeuseifstoredincoldarea.Internalsoftwarefaulttopreventsystemdamageorincorrectpressure.Turnpowerswitchonsideofunitofffor�0secondsandbackontoresumenormaloperation.Ifproblempersists,contactyourROHO/SelectAirDistributorforassistance.

8. Patient comes in contact with bed frame after running Auto comfort mode.Autocomfortonlyprovidesapproximateadjustmentofcomfortlevel.Thecaregivermustensurecorrectflotationlevelofpatient.Ensurepatienthasnotchangedtheirweightdistributiononthemattresssincesettingcomfortlevel,suchaslyingonsideordrawinglegsupward.Seethe“ManualSetup”section.

9. Refer to the "Safety Precautions" and "Important Safeguards" sections of this manual for additional guidance.

••

•••

••

��

SelectAir

Upright ModeTheUprightModeincreasessystempressuretocompensatefortheuprightpatient.Note: Whenthepatientissittingupinbed,additionalsystempressure isrequiredtokeepthepatientproperlysupported.

Beforeraisingthepatienttoasittingposition,activatetheUprightModebypressingthe"UprightOn/Off"buttononce(EnsuretheUprightlightilluminates),(fig.14).

TodeactivatetheUprightMode,firstlowerthepatienttoalyingposition.

Section�0 SelectAirFigure�3

Figure�4

��

Note: To assist in deflating the mattress, disconnect the hose at themattressorcontrolunit.

Thenpressthe"UprightOn/Off"buttonasecondtime(Ensuretheuprightlightextinguishes).

Note:DonotleavethecontrolunitintheUprightModewhenthe patientislyingflatorataslightangle. Note: Ensurethepatienthasatleastone(1)inch(3cm)ofclearance betweenthebedframeandtheirbody.Ifnot,manuallyincreaseor decreasesystempressuretocompensate.

Firm Mattress ModeToaidintheplacementandmaneuveringofthepatient,thecontrolunitisequippedwithaFirmMattressMode.TheFirmMattressModewillfullyinflatethemattressmakingitfirmforeasypositioning.TheFirmMattressModewillautomaticallyterminatewhenthetimedisplayedonthekeypadhasexpired.

Pressthe"Firm"buttononthekeypad.Thedisplaywillindicatetheremainingtime(fig.15).

ToendthecyclepresstheFirmMattress“Off”button.

Note: TheSelectAircontrolunitisequippedwithaninternaltimerwhichwill turntheFirmMattressModeoffafter�0minutes.IftheFirmMattress Modehastimedoutandendedthefirmmattresscycle,DONOTpress theFirm"Off”keyasthismaycausethesystemto"lockup".Note: PressingtheFirm"Off"keymultipletimesorholdingdownthebutton maycausethesystemto“lockup”.Note: Toensurepatientcomfort,thecontrolunitslowlylowersthepressureof thesystem.Thismaygivetheappearancethatthefirmfunctionisstill active.Ifthetimerlightsareextinguished,thecontrolunitisinits normalmode.

Section�0 SelectAir

Figure�6SelectAir,

SelectAirMax,HybridSelect

Models

Flashing“Green”Light

(PowertoControlUnit)

CPR/Emergency Deflate Important:IncaseofaCPREmergency,turnpowerOFFbypressingthe CPRbuttononthekeypad.

Figure�5

Section�� SelectAirMax

Figure�7

SelectAir Max Upright ModeTheUprightModeincreasessystempressuretocompensatefortheuprightpatient.Note:Whenthepatientissittingupinbed,additionalsystempressure isrequiredtokeepthepatientproperlysupported.

Beforeraisingthepatienttoasittingposition,activatetheUprightModebypressingthe"UprightOn/Off"buttononce(EnsuretheUprightlightilluminates).(fig.18).

Figure�8

Figure�9

TodeactivatetheUprightMode,firstlowerthepatienttoalyingposition.Thenpressthe"UprightOn/Off"buttonasecondtime(Ensuretheuprightlightextinguishes).

Note:DonotleavethecontrolunitintheUprightModewhenthe patientislyingflatorataslightangle. Note:Ensurethepatienthasatleastone(1)inch(3cm)ofclearancebetween thebedframeandtheirbody.Ifnot,manuallyincreaseordecrease systempressuretocompensate.

Note: TheSelectAirMaxcontrolunitisequippedwithaninternaltimerwhichwill turntheFirmMattressModeoffafter�0minutes.IftheFirmMattress Modehastimedoutandendedthefirmmattresscycle,DONOTpress theFirm"Off”keyasthismaycausethesystemto"lockup".Note: PressingtheFirm"Off"keymultipletimesorholdingdownthebutton maycausethesystemto“lockup”.Note: Toensurepatientcomfort,thecontrolunitslowlylowersthepressureof thesystem.Thismaygivetheappearancethatthefirmfunctionisstill active.Ifthetimerlightsareextinguished,thecontrolunitisinits normalmode.

System LockControlunitisequippedwiththeSystemLockwhichsuspendsnormalkeypadoperations(withexceptionofFirmMattress,UprightandCPRon/off)untildeactivated.WhentheFirmMattressbuttonispressedwhiletheSystemLockisactivated,theSystemLocklightwillextinguishuntiltheFirmMattressModeturnsoff.

1. Tolockthecontrolpanel,pressthe“SystemLock”button(fig.20).TheSystemLocklightwillcomeon.

Figure�0 Light

Figure�� Light

Tounlockthecontrolpanel,pressandholdthe“SystemLock”buttonforthree(3)seconds. EnsuretheSystemLocklightextinguishes.

Auto ComfortThiscontrolunitisequippedwiththeAutoComfortmode.Whenselected,thecontrolunitwillproceedthroughoneorseveral(dependingonthepatient'sbodytype)cyclesandwillthencalculatetheapproximatepropersettingforthepatient.Ifthesettingselectedbythecontrolunitisnotacceptable,thenasecondrunoftheAutoComfortcyclemaybenecessary.IfmanualsetupisdesiredseeManualSetup,Section6.

�. Turnthecontrolunitonandallowthemattresstofullyinflatebeforemakingany adjustmentsorplacingthepatientonthemattress.�. Placethepatientonthemattress,centeredandintheirhabitualrestingposition,i.e.ontheirback,ontheirside,etc. Note:Thebedrailsshouldbelockedintheirhighestpositionbeforeproceeding.3. DeactivatetheFirmModebeforestartingAutoComfort.4. PresstheAutoComfort“Start”button(fig.21). Note:ThepatientmustremainstillwhiletheAutoComfortlightisflashing.

Note:DonotpressanyotherkeysuntiltheAutoComfortlightisextinguished.5. Inspectthepatienttoensuretheyhavesunkintothemattressabout40-50%and nottouchingtheframeatanypoint.Iftheyhavenot,adjusttheComfortLevel usingtheComfortLevel“Softer”and“Firmer”buttonsuntiltheproperresults areachieved.

Pulsate ModeThiscontrolunitisequippedwiththePulsateMode.Whenselected,thecontrolunitwillcontinuouslyreadjustthesystempressure(proportionaltotheComfortLevelsetting).Changeinpressureisgradualtoensuremaximumpatientcomfort.�. Toactivate,presseitherthe“High”,“Medium”or“Low”key(fig.22)onthecontrol panel.ThePulsatelightwillcomeon.

Figure�� Light

�.ThePulsateModeadjustsasfollows: Low–�0%cycleevery�5minutes Medium–�0%cycleevery7minutes High–�0%cycleeveryminute.

3. TodeactivatethePulsateMode,pressthePulsateoff button(Fig.23).

Note: YoumaychangetherateofalternatingpressureatanytimewhilethePulsate Modeisinoperation.

Figure�3

Figure�4

HybridSelectModels

CPR/Emergency Deflate

Important: IncaseofaCPREmergency, turnpowerOFFbypressingtheCPRbuttononthekeypad.

Section�� BariSelect

Figure�5

BariSelect

Upright ModeTheUprightModeincreasessystempressuretocompensatefortheuprightpatient.Note:Whenthepatientissittingupinbed,additionalsystempressure isrequiredtokeepthepatientproperlysupported.

Beforeraisingthepatienttoasittingposition,activatetheUprightModebypressingthe"Upright"buttononce(fig.26).

Figure�6

TodeactivatetheUprightMode,firstlowerthepatienttoalyingposition.Thenpressthe"Upright"buttonasecondtime.EnsuretheUprightModeisnotindicatedontheLCDdisplay.

Note:DonotleavethecontrolunitintheUprightModewhenthe patientislyingflatorataslightangle. Note:Ensurethepatienthasatleastone(1)inch(3cm)ofclearance betweenthebedframeandtheirbody.Ifnot,manuallyincreaseor decreasesystempressuretocompensate.

Firm Mattress ModeToaidintheplacementandmaneuveringofthepatient,thecontrolunitisequippedwithaFirmMattressMode.TheFirmMattressModewillfullyinflatethemattressmakingitfirmforeasypositioning.TheFirmMattressModewillautomaticallyterminatewhenthetimedisplayedontheLCDhasexpired.

ToendthecyclepresstheFirmbuttonasecondtime.EnsuretheFirmModeisnotindicatedontheLCDdisplay.

Note: TheBariSelectcontrolunitisequippedwithaninternaltimerwhichwill turntheFirmMattressModeoffafter�0minutes.IftheFirmMattress Modehastimedoutandendedthefirmmattresscycle,DONOTpress theFirmkeyasthismaycausethesystemto"lockup".Note: PressingtheFirmkeymultipletimesorholdingdownthebutton maycausethesystemto“lockup”.Note: Toensurepatientcomfort,thecontrolunitslowlylowersthepressureof thesystem.Thismaygivetheappearancethatthefirmfunctionisstill active.IftheFirmmodeisnotindicatedontheLCDdisplay,thecontrol unitisinitsnormalmode.

System LockTheBariSelectcontrolunitisequippedwiththeSystemLockwhichsuspendsnormalkeypadoperations(withexceptionofFirmMattress,UprightandCPRbuttons). • Tounlockthecontrolunit,pressandholdthe“Lock/Unlock” button(Fig.28)until“Unlock”isdisplayedintheLCDanda beepisheard(approx.3seconds).

FirmFigure�7

• Tolockthecontrolpanel,pressthe“Lock/Unlock”button.Ifnopatientactivity is detectedfor60seconds,thecontrolunitwillautomaticallylockthesystem.

Auto ComfortTheBariSelect controlunitisequippedwiththeAutoComfortmode.Whenselected,thecontrolunitwillproceedthroughoneorseveral(dependingonthepatient'sbodytype)cyclesandwillthencalculatetheapproximatepropersettingforthepatient.Ifthesettingselectedbythecontrolunitisnotacceptable,thenasecondrunoftheAutoComfortcyclemaybenecessary.IfmanualsetupisdesiredseeManualSetup,Section6.

Turnthecontrolunitonandallowthemattresstofullyinflatebeforemakinganyadjustmentsorplacingthepatientonthemattress.Placethepatientonthemattress,centeredandintheirhabitualrestingposition,i.e.ontheirback,ontheirside,etc.

Note: Thebedrailsshouldbelockedintheirhighestpositionbefore proceeding.

DeactivatetheFirmModebeforestartingAutoComfort.PresstheAutoComfort"Start"button(Fig.29).

Note: Thepatientmustremainstilluntilthecycleiscomplete. Note: DonotpressanyotherbuttonsuntiltheAutoComfortcyclecompletes.

Inspectthepatienttoensuretheyhavesunkintothemattressabout40-50%andnottouchingtheframeatanypoint.Iftheyhavenot,adjusttheComfortLevelusingtheComfortLevel"Softer"and"Firmer"buttonsuntiltheproperresultsareachieved.

Note:Becauseweightdistributionvariesfrompatienttopatient,some patientsmayrequireanincreaseordecreaseintheComfortLevel.

••

Figure�9

Figure�8

Manual Weight Input BariSelectWheninnormaloperatingmode,presstheManualbuttononthekeypad(fig.30).Thecontrolunitwillentermanualweightinputmode.Thedisplaywillchangefromthesystempressureleveltouserweightinpounds,startingat400poundseachtimethemanualmodeisentered.

UsetheFirmerandSofterbuttonstoadjustthedisplayedweighttotheapproximateweightoftheuser(fig.31).TheFirmerbuttonwillincreasethedisplaybytwenty(20)poundswitheachpress,theSofterbuttonwilldecreasethedisplayby(10)poundswitheachpress.

Oncethedesiredweightisdisplayedandnobuttonsarepressedforfive(5)seconds,thecontrolunitwillreverttonormaloperation.Thedisplaywillrevertbacktothesystempressurelevelandthecontrolunitwillthenadjustthepressuretothenewsetpoint.Allowtimeforthesystempressuretostabilizebeforemakingfurtheradjustments.

Pulsate ModeTheBariSelectcontrolunitisequippedwiththePulsateMode.Whenselected,thecontrolunitwillcontinuouslyreadjustthesystempressure(proportionaltotheComfortLevelsetting).Thechangeisgradualtoensuremaximumpatientcomfort.

• Unlockthecontrolunit. • PressthePulsatekey(Fig.32). • SelectthePulsatemodesettingbypressingtheupanddownkeys. • PressthePulsatekeytosetthemodeintomemory.Ensuretheproper modeisindicatedontheLCDscreen.

YoumaychangetherateofpulsationatanytimewhilethePulsateModeisinoperation.

Figure30 Manual1

Figure3�

Figure33

CPR/Emergency Deflate

Important: IncaseofaCPREmergency, turnpowerOFFbypressingtheCPRbuttononthekeypad.

BariSelectModelsonly

HybridSelect

Upright ModeTheUprightModeincreasessystempressuretocompensatefortheuprightpatient.Note: Whenthepatientissittingupinbed,additionalsystempressure isrequiredtokeepthepatientproperlysupported.

Beforeraisingthepatienttoasittingposition,activatetheUprightModebypressingthe"UprightOn/Off"buttononce(EnsuretheUprightlightilluminates,(fig.35).

Section�3 HybridSelect

Figure34

Figure35

TodeactivatetheUprightMode,firstlowerthepatienttoalyingposition.Thenpressthe"UprightOn/Off"buttonasecondtime(Ensuretheuprightlightextinguishes).

Note:DonotleavethecontrolunitintheUprightModewhenthe patientislyingflatorataslightangle. Note:Ensurethepatienthasatleastone(1)inch(3cm)ofclearance betweenthebedframeandtheirbody.Ifnot,manuallyincreaseor decreasesystempressuretocompensate.

Note: TheHybridSelectcontrolunitisequippedwithaninternaltimerwhich willturntheFirmMattressModeoffafter�0minutes.IftheFirm MattressModehastimedoutandendedthefirmmattresscycle,DO NOTpresstheFirm"Off”keyasthismaycausethesystemto"lockup".Note: PressingtheFirm"Off"keymultipletimesorholdingdownthebutton maycausethesystemto“lockup”.Note: Toensurepatientcomfort,thecontrolunitslowlylowersthepressureof thesystem.Thismaygivetheappearancethatthefirmfunctionisstill active.Ifthetimerlightsareextinguished,thecontrolunitisinits normalmode.

System LockControl unit is equipped with the System Lock which suspends normal keypadoperations(withexceptionofFirmMattress,UprightandCPRon/off)untildeactivated.When theFirmMattressbutton ispressedwhile theSystemLock isactivated, theSystemLocklightwillextinguishuntiltheFirmMattressModeturnsoff.

1. Tolockthecontrolpanel,pressthe“SystemLock”button(fig.37),theSystemLocklightwillcomeon.

Light Figure37

Figure36

2. Tounlockthecontrolpanel,pressandholdthe“SystemLock”buttonforthree(3)seconds.EnsuretheSystemLocklightextinguishes.

Pulsate ModeThiscontrolunitisequippedwiththePulsateMode.Whenselected,thecontrolunitwillcontinuouslyreadjustthesystempressure(proportionaltotheComfortLevelsetting).Changeinpressureisgradualtoensuremaximumpatientcomfort.

Toactivate,presseither“High”or“Low”key(fig.38)onthecontrolpanel.ThePulsatelightwillilluminate.

ThePulsateModeadjustsasfollows: Low–�0%cycleevery5minutes High–�0%cycleunderoneminute

TodeactivatethePulsateMode,pressthePulsateOFF button(Fig.39).

Note: Youmaychangetherateofalternatingpressureatanytimewhilethe PulsateModeisinoperation.

Figure40SelectAir,

SelectAirMax,HybridSelect

Models

CPR/Emergency Deflate Important:IncaseofaCPREmergency,turnpowerOFFbypressingthe CPRbuttononthekeypad.

Figure39

Figure38

SelectAirSystemSpecifications: SelectAir SelectAirMax

BariSelect (allsizes)

HybridSelect

MattressSystemType Mattressreplacement

Mattressreplacement

MattressOverlay

PatientWeightLimit 400lbs. 400lbs. 680lbs. 300lbs.

OneYearLimitedWarranty x x x x*

ControlUnitSpecifications:

UL544Certification#E183348 x x x x

Current-Lessthan3amps x x x x

Voltage-��0VAC50/60Hz x x x x

FlowRate80-�00SLPM x x x x

Mattress,Cover,Foam,SheetSpecifications

Flammability-�6CFRPart�63�(compositetesting) x x x x

Latexfree x x x x

SurfaceResistivity-AntiStatic x x x x

BacterialResistance-MeetsAATCC-�47-�993 x x x x

ControlUnitFeatures: SelectAir SelectAirMax

BariSelect(allsizes)

HybridSelect

Softer/Firmer-Pushtoincrease(firmer)ordecrease(softer)comfortlevel.

x x x x

Upright -Increasespressuretocompensatefortheuprightpatient. x x x x

Firm-Fullyinflatesmattresstoaidinplacementandmaneuveringofpatient.

x x x x

System Lock-Locksthesystemtodeterunauthorizedpersonnelfromalteringthesettings.

Auto Comfort-Automaticallyadjuststhesystemaccordingtothepatient’sweightdistribution.

Section�4 SelectAirProductInformation

Pulsation-Continuallyreadjustssystempressure.SelectAirMax&BariSelect-Low-every�5minutes,Medium-every7minutes,High-everyminute.HybridSelect-Low-every5minutes,High-everyminute.

CPR/Emergency Deflate -Whenengaged,allowsquickdeflationofthesystemincaseofanemergency.

x x x x

Digital Display-(LCD)-Easytoreaddigitaldisplay. x

Remote Capability-Anoptionalhandcontrolisavailable(additionalcost)whichallowsthepatienttoself-adjustthesofter/firmerandpowerfeatures.

Back-lit Keys-Allowsystemfeaturestobevisibleindim/darkenvironments.

ControlUnitFeatures(con't): SelectAir SelectAirMax

BariSelect(allsizes)

HybridSelect

*RefertoDRYFLOATATIONcushioningproductOperationsManualforcushioninformation.

Section�4 SelectAirProductInformation

Limited Warranty

TheROHOGroup,Inc.warrantstheSelectAirmattresssystems'controlunitsforaperiodoftwelve(12)monthsfromdateofpurchase.Themattress,coverandallothermattresssystemcomponentswillbewarrantedforaperiodoftwelve(12)months.

TheROHOGroup,Inc.warrantstheHybridSelectLowAirLossMattressOverlaySystemandControlUnitforaperiodoftwelve(12)monthsfromdateofpurchase.TheHybridSelectmattressoverlay,coverandallotheroverlaysystemcomponentswillbewarrantedforaperiodoftwelve(12)months.EXCEPTION:TheROHOHIGHPROFILEcushion(HealFloatfeature).Refertothecushion’soperationsmanualforitsspecificlimitedwarranty.

TheROHOGroup, Inc.will repair or replace (at itsoption)anycomponents that, uponexaminationbyaROHO/SelectAirrepresentativeoragent,arefoundtobedefectivewithinthelimitsofthewarranty.

Toobtainserviceunderthetermsofthiswarranty,theusermustnotifyTheROHOGroup,Inc.,itsrepresentativesoragentofthedefectnotedwithinthetimelimitofthiswarranty.TheROHOGroup,Inc.willarrangefortheinspectionand/orreturnofthesystemorcomponent.Nosystemorcomponentwillbeacceptedforthereturnwithoutexpresspriorauthorization.AnyrepairmadetotheequipmentorcomponentsbyanyoneotherthananROHO/SelectAirRepresentative,VOIDSthiswarrantyinitsentirety.Systemsorcomponentstobereturnedmustbecleaned(disinfected)priortoreturn,andmustbesecurelypackaged.

This warranty does not apply to any products that have been subjected to damage inaccident,misuseorabuse.

The patient assumes all risk and liability in connection with determining the suitabilityof the system and its components for a particular use.The ROHOGroup, Inc. and itsrepresentativesandagentsshallnotbeliableforinjury,lossordamagearisingoutoftheimproperuseoroperationofthesystem.Therearenowarranties,impliedbeyondthosestated for any consequential damages or loss resulting from failure of this product toperforminthemanneranticipated.

Forascheduleofrepairsandcosts,contactyourROHO/SelectAirrepresentative.

Somecountriesmaynotallowtheexclusionor limitationsof incidentalorconsequentialdamages,sotheabovelimitationsorexclusionsmaynotapplytoyou.

ROHO HIGH PROFILE Cushion (HealFloat Feature)–Seethewarrantysectionintheoperationsmanualthatissuppliedwiththecushion.

Section�5 Warranty

�00NorthFloridaAvenueBelleville,IL6��-54�9USA

www.therohogroup.comU.S.&Canada:�-800-85�-3449Fax�-888-55�-3449

OutsideU.S.&Canada:�-6�8-�77-9�50Fax�-6�8-�77-65�8T�0000��/06

the Roho Group, Inc. - Athome Medical · ENGLISH Section Introduction -3 Section System Components...

Documents