Post on 31-Oct-2019
transcript
LAPORAN HASIL PENELITIAN DISERTASI DOKTOR
TAHUN ANGGARAN 2010
Judul : PENGEMBANGAN EKSTRUDER ULIR TUNGGAL SEBAGAI UNIT PENGADUKAN DALAM PEMBUATAN EDIBLE FILM DENGAN PROSES COMPRESSION MOLDING
Peneliti :::: TRIANA LINDRIATI
Dibiayai Oleh Direktorat Jenderal Pendidikan Tinggi, Kementerian Pendidikan Nasional sesuai dengan Surat Perjanjian Penugasan Dalam Rangka Pelaksanaan
Penugasan Penelitian Disertasi Doktor Tahun Anggaran 2010 Nomor : 492/SP2H/PP/DP2M/VI/2010, tanggal 11 Juni 2010.
Universitas Brawijaya Malang 2010
BIDANG ILMU : REKAYASA
RINGKASAN
Pengembangan Ekstruder Ulir Tunggal Sebagai Unit Pengadukan dalam
Pembuatan Edible film dengan Proses Compression Molding: Triana Lindriati, 0730401058; 2010; 50 Halaman; Program Doktor Ilmu-Ilmu Pertanian; Teknologi Pengolahan Hasil Pertanian: Fakultas Pertanian: Universitas Brawijaya.
Aplikasi edible film dalam industri makanan terkendala karena belum tersedianya teknologi untuk produksi sistem kontinyu berskala besar. Compression Molding merupakan teknologi yang telah banyak diaplikasikan dalam pembuatan lembaran polimer sintetis. Beberapa penelitian terdahulu menunjukkan bahwa, edible film dapat dibuat dengan menggunakan teknologi Compression Molding. Akan tetapi diperlukan perlakuan pendahuluan untuk mencampur bahan-bahan dasar penyusun edible film. Geometri ekstruder ulir tunggal dapat dikembangkan dan memberikan efek pengadukan intensif.
Penelitian bertujuan untuk mengembangkan ekstruder ulir tunggal sebagai unit pengadukan dalam pembuatan edible film dengan proses Compression Molding, karena geometri dari ekstruder ulir tunggal dapat memberikan efek pengadukan intensif. Penelitian diawali dengan pembuatan ulir ekstruder (variasi compression ratio 1,5; 2,5 dan 3,5) dari stainless steel dengan menggunakan mesin CNC turning. Software GAMBIT 2.2.30 dan ANSYS FLUENT 6.3.26. digunakan untuk menganalisa distribusi gaya geser dan kecepatan alirbahan sepanjang ulir.
Penelitian dibagi menjadi dua tahapan. Penelitian Tahap I menggunakan Rancangan Acak Lengkap satu faktor untuk menentukan komposisi isolat protein kedelai (ISP) dan tapioca yang divariasikan 100%, 90%, 80%, 70%, 60%, 50%, 40%, 30%, 20%, 10%, 0%. Penelitian Tahap II untuk mempelajari pengaruh kecepatan putar ulir (60, 100, 140 rpm) dan compression ratio (1,5; 2,5; 3,5) terhadap karakter adonan dan edible film. Luaran dari penelitian ini diharapkan mampu meningkatkan penggunaan edible film pada industri pangan, sehingga mendukung program food safety dan pelestarian lingkungan.
Hasil penelitian menunjukkan adanya pengaruh komposisi ISP : tapioka terhadap Water Holding Capacity (WHC), tekstur dan aktifitas air (aw) adonan dan juga berpengaruh terhadap kekuatan tarik, perpanjangan dan kelarutan edible film. Komposisi yang menghasilkan edible film dengan karakter yang optimum adalah 30%. Pada penelitian Tahap II, hasil penelitian menunjukkan bahwa kecepatan putar dan compression ratio ulir berpengaruh terhadap WHC, tekstur dan aw adonan demikian juga berpengaruh terhadap kekuatan tarik, perpanjangan dan kelarutan edible film. Kondisi operasi yang dapat menghasilkan edible film dengan karakter yang optimum adalah kecepatan putar 60 rpm dan compression ratio 3,5. Dari penelitian ini dihasilkan edible film yang transparan dengan kekuatan tarik 0,619 Mpa, perpanjangan77,500 % dan kelarutan 0,243.
SUMMARY
Development of Single Screw Extruder as Mixing Unit in The Production of Compressionmolded Edible Film. Triana Lindriati, 0730401058; 2010; 50 Pages; Agricultural Doctoral Programs; Agriculture Product Technology, Brawijaya University.
Much of research in to edible films has involved the production of films from the
method of solvent casting. Solvent casting method is not suitable for large scale and continue production. Thermal method such as compression molding has received only limited attention. The advantage of compression molding films compared with solvent casting films is that former requires less processing time and space. The compression molding need post process to make the dough homogeny before pressed. The post process that is possible to develop is dispersive mixing. Geometry of single screw extruder may induce the required of dispersive mixing.
The aim of this research is developing single screw extruder as mixing unit in compression-molded edible film formation. Screw in this research varied in compression ratio (1,5; 2,5 dan 3,5) and made from stainless steel. Software GAMBIT 2.2.30 and ANSYS FLUENT 6.3.26. were used to analyze shear stress and flow rate distribution.
This research was divide in to two stage. The first stage studied about the effect of dough composition (Isolate soy protein : tapioca : 0%, 10%, 20%, 30%, 40%, 50%) on dough and edible film characters. The second stage, studied about the effect of srew speed (60, 100, 140 rpm) and compression ratio (1,5; 2,5; 3,5) on dough and edible film characters. The measured parameters were water holding capacity, texture, water activity of dough and tensile strength, elongation, solubility of films.
The result showed that composition of dough affect on water holding capacity, texture, water activity and tensile strength, elongation, water solubility of film. The optimum composition was 30%. The second stage study showed that screw speed and compression ratio had effect on of all the parameter measured. The operation condition that gave optimum film properties was 60 rpm screw speed and 3.5 compression ratio. The edible films produce from this research have properties: 0.619 Mpa of tensile strength; 77.5 % of elongation and 0.243 of solubility on water.
DAFTAR PUSTAKA
Alonso, R., E.Orue, M.J. Zalbalza, G. Grant and F. Marzo, 2000. Effect of extrusion cooking on structure and functional properties of pea and kidney bean proteins. J. Sci Food Agric., 80: 397-403
Arêas JA., 1992. Extrusion of food proteins. Crit Rev Food Sci., 32(4):365–392. Ballandran-Quintana, R.R, G.V. Barbosa-Canovas, J.J. Zazueta-Morales, A.
Anzaldua-Morales and A. Quintero-Ramos, 1998. Functional and nutritional properties of extruded whole pinto bean meal (phaseolus vulgaris L.) J. of Food Sci., 63 (1): 113-116.
Banker, R.A., E.A. Baldwin and M.O. Nisperos-Carriedo, 1994. Edible Coatings and
Films for Processed Foods. Dalam Krochta, J.M., E.A. Balwin and M.O. Niperos-Carriedo (Eds). Edible Coatings and Films to Improve Food Quality. Technomic Publishing, Lancaster, Basel.
Brandenburg, A.H., C.L. Weller, R.H. Testin, 1993. Edible films and coating from soy
protein. J. Food. Sci., 58(5):1086-1088 Burguess L.D. and D.W. Staenly, 1976. A possible mechanism for thermal
texturization of soybean protein. Can. Inst J. of Food Science Technol., 9:228-231.
Buick, J.M. and J.A. Cosgrove, 2006. Numerical simulation of the flow field in the
mixing section of a screw extruder by lattice boltzmann model. Chemical Engineering science, 61: 3323-3326.
Chang, Y.P., P.B. Cheah and C.C. Seow, 2000. Plasticising-antiplasticising effect of
water on physical properties of tapioca starch films in the glassy state. J. Food Sci. 65 (3):445-451
Circle, S.J., E.W. Meyer and R.W. Whitney, 1964. Rheology of soy protein
dispersions. Effect of heat and other factors on gelation. Cereal Chem., 41:157-172.
Cunningham P., A.A. Ogale, P.L. Dawson, J.C. Acton, 2000. Tensile properties of soy
protein isolate films produced by a thermal compaction technique. J. Food Sci 65(4):668-671.
Cuppet, S.L., 1994. Edible coatings as carrier of food additives, fungicides and natural
antagonists. In Krochta J.M., Baldwin E.A., Nisperos-Carriedo M.O., Edible coatings and films to improve food quality. Lancaster, Pa, Technomic Publishing Company, Inc.
Cuq,B., N. Gotard, J.L. Cuq and S. Guilbert, 1996. Fungcional properties of
myofibrillar protein-based biopackaging as affested by film thickness. J. of Food Sci., 61(3):580-584.
Cuq, B., N. Gontard, S. Guilbert, 1997. Thermoplastic properties of fish myofibrillar
proteins: application to biopackaging fabrication. Polymer, 38(16):4071-4078 Darmadji, P., 2002. Aplikasi “Response Surface Methodology” untuk Optimasi Proses
dengan Parameter Sensoris. Seminar Nasional PATPI Malang, 30-31 Juli 2002.
Di Gioia L and S. Guilbert, 1999. Corn protein-based thermoplastic resins: effect of
some polar and amphiphilic plasticizers. J Agric Food Chem., 47:1254–1261. Domingues, N., M. Camesasca, M. Kaufman, I. Manas-Zloczower, A. Gaspar-Cunha
and J.A. Covas, 2006. Modelling Agglomerate Dispersive in Single Screw Extruders. Proceedings of the Int. Conf. ANTEC, Charlotte.
Druchta, J.M. and C.J. DeMulder Jonhston, 1997. An Update on edible films.
Scientific Summary. Food Technol., 51(2):60-63. Fellows, P., 1988. Food Procesing Technology. Principles and Pratice. Ellis
Horwood. Fenner, R.T., 1979. Principles of Polimer Processing. London. Macmillan Press
Ltd. Gennadios,A. and C.L. Weller, 1992. Tensile strength increase of wheat gluten films.
ASAE paper in International Winter Meeting American Society of Agricltural Engineers, December, 1992. Nashvill.
Gennadios, A., A.H. Brandenburg, C.L. Weller, R.F. Testin, 1993. Effect of pH on
properties of wheat gluten and soy protein isolate films. J. Agri Food Chem., 41(11): 1835-1839
Gujska, E and K. Khan, 1991. High temperature extrusion effects on protein solubility
and distribution in Navy and Pinto beans. J. Food Sci., 56: 1013-1016. Guy, R., 2003. Extrusion Cooking, Technologies and Applications. Woodhead
Publishing Limited, Cambridge. Halick, J.V. and V.J. Kelly, 1959. Gelatinization and pasting characteristics of rice
varieties as related to cooking behavior. Cereal Chem., 36:91-98. Harper, J.M., 1981. Extrusion of Food. Boca Raton, Fla. CRC Press Inc. Hernandez-Izquierdo VM. 2007. Thermal transitions, extrusion, and heat-sealing
of whey protein edible films [dissertation]. Davis, Calif.: Univ. of California. Horiguchi, H., K. Takahashi, T. Tokota, 2003. Numerical simulation of the flow field in
the mixing section of a screw extruder by lattice gas automata method. Journal of Chemical Engineering Japan, 36: 110-113.
Jane, J-L, S.Wang, 1994. Soy protein-based thermoplastic composition for preparing
molded articles. United State patent 5.523.293.
Kalyon, D.M. and H.N. Sangani, 1989. An experimental study of distributive mixing in
fully intermeshing, co-rotating twin screw extruders. Polymer Eng and Sci., 29(15):1018-1026
Khinchin, A.I., 1957. Mathematical Foundations of Information Theory. New York,
Dover Kinsella, J.E., S. Damodaran dan B. German, 1985. Physiochemical and Functional
Properties of Isolated Proteins with Emphasis on Soy Proteins. Dalam: Altschul, A.M. and H.L. Wilcke (Eds) New Protein Foods. Academic Press. Orlando.
Krochta, J.M., E.A. Baldwin and M.O. Nisperos-Carriedo, 1994. Edible Coatings and
Film to Improve Food Quality. Technomic Publishing Co. Inc. Lancaster.Bassel.
Krochta, J.M. and De Mulder-Johnston C., 1997. Edible and biodegradable polymer
film : Challenges and opportunities. Food Technol., 51(2):61-72 Kunte, L.A., A. Gennadios, S.L. Cuppett, M.A. Hanna and C.L. Weller, 1997. Cast
films from soy protein isolates and fractions. Cereal Chemistry, 74: 115-118. Laemmli, U.K., 1970. Cleavage of structural proteins during the assembly of the head
of bacteriophage T4. Nature, 227: 680-685. Lanfer-Marquez, V.M. and F.M. Lajolo, 1991. In vivo digestibility of bean (Phaseolus
vulgaris L.). Protein: The role of endogenous protein. J. Agric. Food Chem.,39:1211-1215.
Layuk, P., D.W. Marseno dan Haryadi. 2001. Karakterisasi edible film komposit pectin
daging buah pala. Himpunan Makalah Seminar Nasional Teknologi Pangan.PATPI. Semarang.
Liu L, J.F. Kerry , J.P. Kerry , 2006. Effect of food ingredients and selected lipids on
the physical properties of extruded edible films/casings. Int J Food Sci Technol., 41:295–302.
Lindriati, T. dan H. Arbiantara, 2009. Pengembangan Teknologi Edible Film Aktif
dari Tepung Koro Pedang. Laporan Penelitian Hibah Bersaing XVI Moraru CI and J.L. Kokini, 2003. Nucleation and expansion during extrusion and
microwave heating of cereal foods. Compr Rev Food Sci F 2:120–138. Mouquet, C., B. Salvignol, N. Van Hoan, J. Monvois, S. Treche, 2003. Ability of a
“very low cost extruder” to produce instant infant flour at a small scale in Vietnam.Food Chem. 82: 249-255
Ogale A.A, P. Cunningham, P.L. Dawson, J.C. Acton, 2000. Viscoelastic, thermal and
microstructural characterization of soy protein isolate films. J. Food Sci., 65(4):672-679.
Pol H., P. Dawson, J. Acton, A. Ogale, 2002. Soy protein isolate/corn-zein laminated
films: transport and mechanical properties. J. Food Sci., 65(4):672-679. Pommet, M., A. Redl, M.H. Morel, S. Domenek, S. Guilbert, 2003. Thermoplastic
processing of protein-based bioplastics: chemical engineering aspects of mixing,extrusion and hot molding. Macromol Symp., 197:207-217.
Pommet, M., A. Redl, S. Guilbert, M.H. Morel, 2005. Intrinsic influence of various
plasticizer on functional properties and reactivity of wheat gluten thermoplastic materials. J. Cereal Sci., 42: 81-91.
Rauwendaal, C., 1986. Polymer Extrusion. Hanser Publisher, New York. Rauwendaal, 1991. Mixing in Polymer Processing. Marcel Deckker, Inc., New york. Rauwendaal, C., 1998. Polymer Mixing, A Self-Study Guide. Carl Hanser, Verlag,
Munich. Rauwendaal, C., 2008. Improve Mixing by Generating Elongational Flow.Extrusion
Engineering, Inc. Los Altos Hills, California. www.rauwendaal.com Redl A, M.H. Morel, J. Bonicel, B. Vergnes, S. Guilbert, 1999. Extrusion of wheat
gluten plasticized with glycerol: influence of process conditions on flow behavior,rheological properties, and molecular size distribution. Cereal Chem.76(3):361–370.
Rhim, J.W., A. Gennadios, A. Handa, C.L. Weller and M.A. Hanna, 2000. Solubiltiy, tensile and color properties of modified soy protein films. J of Agric and Food Chem., 48: 4937-4941.. Rhim, J.W., A. Gennadios, C.L. Weller and M.A. Hanna, 2002. Sodium dodecyl
sulfate treatment improves properties of cast films from soy protein isolate. Industrial
Corps and Products an International Journal, 15: 199-205. Sathe, S.K. and D.K. Salunkhe, 1981. Studies on trypsin and chemotrypsin inhibitory
activities, hemaeglutinating activity, and sugars in the Great Northern beans (Phaseolus vulgaris L). J Food Sci., 46:626-629.
Seng Cheow, C. And S. Yean Yu, 1997. Effect of fish protein, salt, sugar and
monosodium glutamate on the gelatinization of starch in fish starch mixture. J. Of Food Processing and preservation 21: 161-177
Shannon, C.E. and W. Weaver, 1948. The Mathematical Theory of
Communication. Urbana, University of Illinois Press, 1948. Shimada K., and J.C. Cheftel, 1988. Texture characteristics, protein solubility and
sulphydryl group/disulphide bond contents of heat-induced gels of whey protein isolate. J. Agric Food Chem. 36:1018-1025.
Sothornvit, R. and J.M. Krochta, 2000. Plasticizer effect on oxygen permeability of β-
lactoglobulin films. J. Agric Food Chem., 48(12):6298-6302
Sothornvit R and J.M. Krochta, 2001. Plasticizer effect on mechanical properties of
ßlactoglobulin films. J Food Eng., 50:149–155. Sothornvit R., C.W. Olsen, T.H. McHugh, J.M. Krochta, 2003. Formation conditions,
water-vapor permeability, and solubility of compression molded whey protein films. J. Food Sci., 68(6): 1985-1989.
Sothornvit, R. and J.M. Krochta, 2005. Plastisizer in edible films and coatings. In: J.H.
Han. Ed. Innovations in Food Packaging. San Diego, Calif. Elsevier Academic Press.
Sothornvit R., C.W. Olsen, T.H. McHugh, J.M. Krochta, 2007. Tensile properties of
compression-molded whey protein sheets: determination of molding condition and glycerol-content effects and comparison with solution-cast films. J. Food Eng., 78 (3):855-860.
Srihara, P. and J.C. Alexander, 1984. Effect of heat treatment on nutritive quality of plant protein blends. Can. Inst. Food Sci. Technol. J., 2:237-240. Srivastav, C.M. and C. Srinivasan, 1987. Science of Engineering Materials. Wiley Eastern Limited, New Delhi Stevens, M.P., 1999. Polymer Chemistry. An introduction. Oxford University.
Press. New York. Stuchell, Y.M. and J.M. Krochta, 1994. Enzymatic treatments and thermal effects on
edible soy protein films. J Food Sci., 59: 1332-1337.. Subirade, M., I, Kelly, J. Gueguen and M. Pezolet, 1998. Molecular basis of film
formation from a soybean protein: Comparation between the conformation of glycinin in aqueous solution and in films. International Journal of Biological Macromolecules, 23: 241-249.
Tadmor, Z. and I. Klein, 1970. Engineering Principle of Plasticating Extrusion. New
York. Van Nostrand. Reinhold Co. Tadmor, Z. and C.G. Gogos, 1979. Principles of Polymer Processing. John Wiley &
Sons. Waldroup, P.W. and K.J. Smith, 1989. Animal feed uses of legumes. In: Legumes.
Chemistry, Technology and Human Nutrition. R.H. Matthews (Ed). Marcel Dekker Inc, New York.
Yao, W.G., K. Takahashi, Y. Abe, 1996. Analytical study on flow and distributive
mixing of a new type pin mixing section for screw extruder. International of Polymer , XI: 222-227.
Yao, W.G., K. Takahashi, K Koyama, G.C. dai, 1997. Design of a new type pin mixing
section for a screw extruder based on analysis of flow and distributive mixing performance. Chemical engineering Science, 52: 13-21.
Zhang, J., P. Mungara, J. Jane, 2001. Mechanical and thermal properties of extruded
soy protein sheets. Polymer, 42: 2569-2578.