Post on 07-Aug-2018
transcript
8/20/2019 Verylube-catalogue-2013-En_web.pdf
1/40
Catalogue of productsVERYLUBE
© XADO Chemical Group
Metal conditioners
Products for engine.Oil system
Fuel system
Other products
Car body products
Compartment care products
Glass care products
Lubricants
Products for locks
Firearms care products
8/20/2019 Verylube-catalogue-2013-En_web.pdf
2/40
More than 100 items are manufactured under VERYLUBEtrademark. These products have already become popularin more than 35 countries.
Products include fuel and oil additives, highly efficientcleaners, car care products for units, joints, compartment,glass etc.
Whatever part you name in your car, VERYLUBE willsurely offer the product for it!
Dear Customer!
Thank you for your interest in products of VERYLUBEtrademark. The VERYLUBE trademark is a propertyof XADO Chemical Group. VERYLUBE is a high qualityseries of products with a following MOTTO:
«High quality product atan affordable price!»
The present catalogue will help you to get acquainted with a wide range of VERYLUBE
products and choose exactly what you need for your car.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
3/40
| 3
Anticarbon
Product designed to clean piston rings from carbon.
Fast-acting product designed to clean stuck piston rings of gasoline and diesel engines from carbon. It removes all
scale and tar contaminations from the parts surfaces of cylinder-piston group. It does not require oil change after
application.
Advantages
• Restores mobility of stuck piston rings.
• Decreases oil consumption.
• Cleans cylinders and pistons, combustion chambers,and valves from all types of contaminations (scale,
carbon, varnish and tar).
• Restores compression in cylinders.
• Decreases noise of engine operation.
• Removes deposits from spark plugs (glow plugs).
• Decreases the level of harmful exhausts into theatmosphere.
Application instructions
1. Warm up the engine. The engine should be warm but
not hot.
2. Unscrew the plugs (burners). Disconnect the wire of
the ignition timing sensor, Hall sensor or commutator.
3. Spray the substance (up to 5 seconds) through a
nozzle hose (or introduce the content of 1 tube) into
each cylinder. Screw the plugs back. Wait for 10–20
minutes. Unscrew the plugs. Cover the plugholes with absorbing fabric to avoid dirt ying out and
getting onto the paint. Rotate the engine with the
starter for several seconds.
4. Reinstall spark plugs.
5. Start the engine and run it at moderate RPM for up
to 15 minutes. During this time, the residues of the
softened carbon will be removed through the exhaust
system.
Dosage
1 tube — 1 cylinder.
One aerosol can is enough to clean rings from carbonin 20 cylinders.
10 mlArt. XB 42051tube
10 mlArt. XB 42151
tube in blister
320 mlArt. XB 40011aerosol can
Note
Avoid getting the substance onto paint.
Safe for catalytic converters, oxygen sensors, mechanical rubber
goods and sealers.
The VERYLUBE ANTICARBON in tubes can be used for engine oil
system ushing:
1. Introduce ANTICARBON into warmed up engine through the oil
ller neck at a ratio 40 ml of ANTICARBON for 3–5 liters of oil.
2. Let the engine idle for 10–15 minutes.
3. Change oil and oil lter.
Products for engine.Oil system.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
4/40
Products for engine. Oil system4 |
Absolut & Absolut+
Flush for engine oil system.
Quickly and safely cleans engine oil system from all types of contaminations including hard-to-remove varnish (yellowcolor). The dissolved contaminations are kept in suspension state and then removed with the used oil.
Advantages
• Cleans engine oil system up to potential cleannesslevel.
• Cleans cylinder-piston group and restores pistonrings mobility.
• Eliminates knocking and normalizes hydraulic valvelifters operation.
• Improves turbo performance of the engine.
• VERYLUBE ABSOLUT+ cleans piston rings formcarbon more effectively.
Verylube Absolut
It is recommended to use Verylube Absolut with each
oil change or when adding different oil type.
1. Introduce the ush through the oil ller neck in warmed
up engine before oil change.
2. Let the engine idle for 10–20 minutes. Do not drive a car!
3. Change oil and oil lter.
Dosage250 ml (1 can) for 5 L of oil.
Application instructions
Verylube Absolut+
It is recommended to use Verylube Absolut+ for intensive
cleaning of engine oil system before oil change. It is
especially effective for restoring of the piston rings, which
became stuck due to the short-term engine overheating.
If moderate clogging (including vanish deposits
removal or carbon removal from the piston rings).
1. Introduce the ush through the oil ller neck of the
warmed up engine.
2. Drive 75–100 km as usual.
3. Change oil and oil lter.
If signicant clogging (heavy deposits under valve
cover, black sludge on the oil gage).
1. Introduce the ush through the oil ller neck of warmed
up engine.
2. Let the engine idle for 3–5 minutes. Do not drive a car!
3. Change oil and oil lter.
Dosage300 ml (1 can) for 5 L of oil
250 mlArt. XB 40159сan
Absolut
300 mlArt. XB 40164сan
Absolut +
8/20/2019 Verylube-catalogue-2013-En_web.pdf
5/40
| 5
Flushing oil
Mineral low-viscosity oil with a complex of special additives for engine and transmission ushing.
Contains revitalizant.
It is designed to clean oil systems of engine and transmission. Special detergent-dispersant, anti-wear and extreme
pressure additives allow safe ushing of oil system (for 30–40 minutes) and its efcient cleaning from all types of
contaminations (up to potential purity). ХАDО revitalizant creates protective reserve against wear during ushing.
Advantages
• Absolutely safe ush of oil system up to the potentialpurity (VitaFlush technology).
• Protective reserve against wear (revitalizationtechnology).
• Possibility of intensive ushing of very contaminatedassemblies (up to 30–40 min) with anti-wear additives.
• Restoration mobility and compression of the oil rings.
• Elimination of the hydraulic compensators lock.
Application instructions
For engines:
1. Drain warm used oil.
2. Pour the ushing oil up to the minimum point on a
probe.
3. Start the engine and let it idle for 10–15 minutes
(if the engine is signicantly clogged — for 30–40
minutes).
4. Stop the engine, pour out the ushing oil, and
replace oil lter.
5. Pour fresh oil.
For transmission assemblies:
1. Drain warm used oil.
2. Pour the ushing oil into the transmission assembly
up to the nominal level.
3. Let the assembly work without any load (with put up
wheels) for 10–15 minutes, and up to 30–40 minutes —
in case of severe clogging.
4.Turn off the engine and drain ushing oil.
5. Pour fresh oil for transmission.
Attention!
Do not drive with the ushing oil in the system!
200 LArt. XB 20550
2 LArt. XB 20250
20 LArt. XB 28750
60 LArt. XB 20450
Package: 2 L — packet; 20 L — сan;
60 и 200 L — barrel
8/20/2019 Verylube-catalogue-2013-En_web.pdf
6/40
8/20/2019 Verylube-catalogue-2013-En_web.pdf
7/40
| 7
Aquastop
Water and ice remover from gasoline.
Fast-acting product designed to remove moisture from fuel system. It breaks up water drops and ice crystals, distributing
them evenly throughout the whole volume of fuel. As a result, moisture is removed together with exhaust gases during
the process of fuel combustion. It keeps fuel system parts in ideal condition and protects them from corrosion. It is
recommended for regular use.
Advantages
• Quickly and efciently removes water from the fuel
system due to emulsication of moisture in gasoline.
• Prevents water condensation in a fuel tank.
• Protects fuel system from corrosion.
Application instructions
To remove moisture and ice from fuel system of
gasoline engines.1. Introduce Verylube Aquastop through the neck of
a fuel tank, at a ratio 10 ml (1 tube) for 5 liters of
gasoline.
2. Run the car as usual.
As a preventive measure (before winter season and
each time at sharp temperature drop).
Add Verylube Aquastop to the fuel tank at a ratio 10 ml
(1 tube) for 20 liters of gasoline at each fueling.
Expert's Advice
For convenient application, squeeze the contents of the
tube into the refueling nozzle before fueling.
Note
To defrost door locks of a car: squeeze a small amount of Verylube
Aquastop into the keyhole. The lock will be defrosted in a minute.
10 mlArt. XB 42056
tube
10 mlArt. XB 42156
tube blister
8/20/2019 Verylube-catalogue-2013-En_web.pdf
8/40
Fuel system8 |
Diesel-Lux
Complex product designed to improve properties of diesel fuel and ush the engine fuel system.
Quickly cleans the fuel system from all types of sediments and contaminations. It protects injector valves from burningand clogging up with tarry sediments. The Diesel-lux Winter (for winter season) signicantly depresses the chilling
temperature of diesel fuel and prevents formation of parafn crystals.
Advantages
• Cleans the fuel system fromcarbon, tarry and varnish
deposits; protects it from wear
and corrosion.
• Increases cetane rating.
• Improves fuel combustion.
• Protects high pressure fuel pumpfrom wear and corrosion.
• Reduces fuel consumption.• Decreases toxic exhausts.
• Removes moisture from fuel.
Application instructions
Squeeze out the contents of the tube
into a fuel tank before refueling.
Expert's Advice
To make the application easy, squeezethe contents of the tube into the refueling
nozzle before fueling.
Note
Compatible with all types of fuel.
VERYLUBE Diesel-lux Winter is introduced when
warmed up to the temperature of +20...25 °С into
non-thickened (transparent) diesel fuel.
Diesel-luxSummer
10 mlArt. XB 42053
tube
10 mlArt. XB 42153tube blister
Diesel-lux
Winter
10 mlArt. XB 42254tube
10 mlArt. XB 42154tube blister
Dosage
Diesel-lux Summer
Preventive dosage
(with every fueling)
1 tube for 50 l of fuel
Repair dosage
(once)1 tube for 20 l of fuel
Diesel-lux Winter
For 50 liters of fuel.
Ambient airtemperature, °С
Tubes,pcs
0… - 20 1
- 20… -30 2
-30… -40 3
8/20/2019 Verylube-catalogue-2013-En_web.pdf
9/40
| 9
Advantages
• Efciently decreases the freezing temperatureof diesel fuel.
• Economical in use, at a ratio 1:10 000.
• Prevents clots and parafn crystals formation.
• Protects lter from plugging when pumpingcold fuel.
• Guarantees easy engine start at low temperature.
Application instructions
1. Squeeze the contents of the tube into a fuel tank(refueling nozzle).
2. Fuel a car following the dosage instructions.
3. Run the car as usual.
Dosage
Up to –20 °С — 1 tube for 100 liters of diesel fuel.
Up to –35 °С — 1 tube for 20 liters of diesel fuel.
Expert's Advice
To make the application easy, squeeze the contents
of the tube into the refueling nozzle before fueling.
Note
VERYLUBE Antigel should be introduced into the non-thickened
(transparent) diesel fuel.
The substance should be warmed up to the temperature of +20...+25 °С
before application.
Antigel
Superconcentrate for diesel fuel.
Special super concentrated product designed to improve the low-temperature properties of diesel fuel. It is used toimprove the uidity and pumpability of fuel at low temperatures.
10 mlArt. XB 42254tube
10 mlArt. XB 42354tube blister
8/20/2019 Verylube-catalogue-2013-En_web.pdf
10/40
Fuel system10 |
Carburetor and injector cleaner
Universal carburetor cleaner.
Product designed for quick and efcient cleaning of carburetors, injector gate as well as air and fuel lines. Easily
removes all types of contaminations (varnish, oil and gasoline lms, scales, sediments and dust) from the fuel system
of a car.
Advantages
• Cleans carburetor parts (choke, oat chamber, jetsand canals) thus restoring their initial performances.
• Restores mobility of the injector choke.
• Removes contaminations from the air introductionmanifold and fuel system.
• Increases engine power and acceleration.
• Reduces harmful exhausts into the atmosphere.
• Decreases fuel consumption.
• Safe for catalytic converters and oxygen sensors.
Application instructions
To clean a carburetor.
1.Take off air lter.
2. Start the engine.
3. Shake the can.
4. Spray liberally onto all visible
carburetor parts. While cleaning
keep up increased engine rpm
with a choker level.
To clean an injector (gate and
air line).
1. Shake the can.
2. Spray the Cleaner onto the
choker (into the air inlet) while
the engine is warm and not
working.
3. Start the engine; keep up
increased engine rpm with a
choker level for 3–5 minutes.
For complex cleaning (fuel
tank, pipelines, jets, inlet
valves, spark plugs and
combustion chambers).
Before fueling, spray the Cleaner
into the ller neck of the fuel tank
(for 10–15 sec per 20 liters of
fuel).
500 mlArt. XB 40109aerosol can
320 mlArt. XB 40009aerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
11/40
| 11
Cleaner of throttle buttery and EGR valve
Efcient product designed to clean throttle buttery of injector, valve of exhaust gas
recirculation system (EGR) and carburetor.
Advantages
• Quickly softens and removes all kinds of contamination.
• Restores operating parameters of the mechanism to thenominal ones.
• Contributes to engine power increase and its acceleration.
• Reduces content of harmful exhaust gases into theatmosphere and decreases fuel consumption.
320 mlArt. XB 40038aerosol can
Quick Start
Product designed for quick engine start.
Efcient product designed for easy and quick starting of engines of all types: gasoline
(carburetor and injector ones), diesel, four- and two-stroke ones, as well as rotary engines.
It is perfect help in winter season.
320 mlArt. XB 40014aerosol can
Advantages
• Makes engine starting exceptionally easy at high humidity, wetspark plugs, weak accumulator and low grade fuel.
• Reduces start-up wear of engines.
• Economical in application.
Application instructions
To start a gasoline engine.
1. Shake the can.
2. Spray Quick Start (for 2–3 seconds)
into the air lter or the inlet air manifold.
To start a diesel engine.
1. Shake the can.
2. Spray Quick Start (for 2–3 seconds) into
an inlet manifold when plugs are off and
gate is open.
Application instructions
To clean a throttle buttery.
Spray a large amount of the product onto a throttle
buttery (into induction manifold of air supply) on a
warmed-up non-running engine. Operate the engine at
high rpm for 3-5 min.
To clean a EGR valve.
Take off the valve. Spray a large amount of the product
onto contaminated surface. Clean dry in 1-2 min. If
necessary, repeat the treatment.
To clean a carburetor.
Take off an air lter. Start the
engine. Spray a large amount
of the product onto all visible
parts of the carburetor. During
cleaning, maintain increased
engine rpm with a lever of the
throttle buttery.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
12/40
12 |
Engine compartment cleaner
Product designed to clean the external parts of an engine and other car
assemblies.
Immediately removes oil spots, dust and grime. After using the cleaner, parts look as new.
Can be used to clean transmission, car suspension and steering assemblies.
Advantages
• Effectively cleans underunderhood space from
oil, varnish, tar and other
contaminations.
• Restores original look ofparts.
• Acts immediately.
Application instructions
1. Switch off the ignition.
2. Shake the can.
3. Spray onto the surface of the engine (assembly,
part) to be cleaned.
4. Let it trickle down together with dirt and wash
with water.
5. Repeat the procedure in case of severe
contaminations.
Other products
320 mlArt. XB 40007aerosol can
500 mlArt. XB 40107aerosol can
Belt reconditioner
Spray designed to take care of driving belts of engine assemblies.
The product is designed to take care of V-belts and multiple V-belts of the pump drives
of the wheel booster, generator, air conditioner etc. Effectively cleans surfaces from
contaminations and restores elasticity of the belts. Protects from cracking and eliminates
slipping.
Advantages
• Cleans the work surface of belts fromcontaminations and oiling; removes
slipping.
• Restores the structure of belt materialand tightens it. Prolongs the service
life of belts and reduces wear.
• Prevents belts from drying and
cracking.
Application instructions
1. Shake the can.
2. Spray onto the work (V-) surface
of a belt.
320 mlArt. XB 40015aerosol can
Note
Does not require rubbing.
Expert's Advice
It is better to clean a cold or slightly warm engine. A high temperature of the engine
provokes fast evaporating of the cleaner and cleaning efciency can be decreased.
Note
Safe for lacquer coating of all types, glass, plastic, rubber and
chrome-plated parts.
Does not contain acid, alkali and other corrosion-hazardous
substances.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
13/40
| 13
Stop Leak liquid radiator sealer
The sealer is designed to prevent leaks in the engine cooling system.
It is the latest generation product for sealing the cooling system leaks. Completely eliminates leaks, permanently and
reliably seals hair cracks and minor damages up to 0.9 mm in the pipelines and joints. Eliminates loose t of the pump
gasket, leakage of cylinder block gaskets etc.
Advantages
• Eliminates the need for expensive repair.
• Universal application for gasoline and dieselengines of cars and other equipment.
• Compatible with all types of uids applied tocooling systems.
• Safe for cooling system parts (gaskets, rubberhoses, aluminum, plastic and steel radiators).
• Lubricates the pump gasket.
• Protects the cooling system against rust andcorrosion.
Application instructions
1. Shake well before use!
2. Warm the engine up to the working temperature, the
engine should be warm but not hot.
3. Add Verylube Stop Leak into the radiator tank when
the engine is not running.
4. Start the engine and let it idle for 5-10 min with the
heating switched on.
250 mlArt. XB 50010can
Attention!
The antifreeze in the cooling system is under pressure
when the engine is hot. Be careful when opening the
radiator/cooling system: hot coolant or steam might
escape from the system.
To avoid eventual leaks in the cooling system, use the
sealer right after changing the antifreeze.
Dosage
The can (250 ml) is designed for cooling system capacity up
to 12 L.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
14/40
Car body products
Plasticor
Antigravel
Plastic corrosion-preventive coating for surface of non-painted fender ares
and car bottom.
Rust preventive product designed to treat fender wells before assembling plastic
protection. Used for overall and local protection of a car body and strengthens existent
coating.
Antigravel rubber coating of light-grey color which allows further painting.
Used for painted surfaces of a car body (lower sections of doors etc.), which are exposed
to road dust and gravel hits. Can be applied to metal, lacquered surfaces and plastics.
Advantages
• Has a high anticorrosion resistance tochemical activity (weak acids, alkali
etc.).
• Protects car body from stone hitting,decreases noise and vibration.
• Forms a thick volumetric coating withthixotropic properties.
Advantages• Forms an elastic lm which is
particularly resistant to stone
hitting.
• Permits further painting.
• Decreases noise and vibration.
• Safely protects from corrosionand chemical activity (road salt).
Application instructions
1. Remove dirt, rust, and dust from the
surfaces to be covered.
2. Shake the can.
3. Spray onto the surface at a distance
of 20–30 cm.4. Apply 2–3 layers on the surfaces to
be coated. Each next layer should be
applied after short-term waiting.
5. Wait 1–2 hours. Run your car or
assemble plastic wings.
Application instructions1. Remove dirt, rust and dust from the
surfaces to be covered with Antigravel.
2. Shake the can.
3. Spray onto the surface at a distance of
20–30 cm.
4. Apply 2–3 layers on the surfaces to be
coated. Each next layer should be applied
after short-term waiting.
5. Wait 30–60 minutes. Run your car.
500 mlArt. XB 40125aerosol can
500 mlArt. XB 40126
aerosol can
Note
The ambient air temperature while treating should be +15…20 °С.
Excess of Plasticor can be easily removed with VERYLUBE Tar Stain Remover.
Keeps high state stability (does not trickle down).
Stable to temperatures up to +85 °С
Note
The ambient air temperature while treating
should be +15…20 °С.
Excess of Antigravel can be easily removed
with Verylube Tar Stain Remover.
14 |
8/20/2019 Verylube-catalogue-2013-En_web.pdf
15/40
| 15
Anticor ML
Wax anticorrosion coating for closed car body areas.
High performance rust preventive product designed to protect internal surfaces of hollow parts of a car body: doorhollows, spars, fenders etc. Specially composed for anti-corrosive treatment of a car body based on the Swedish ML
method (spreading, preserving and "sealing up").
Can be applied on metal and lacquer coating surfaces. Spreads well and penetrates into the smallest cavities which
require protection, such as weld seams and cracks.
Advantages
• Forms a very thin protective lm (from 40 micron) withstrong adhesion.
• Removes moisture.
• Seals up centers of corrosion attacks.
• Has an increased anticorrosion resistance to chemicalactivity (weak acids, alkali etc.).
• Keeps up the form, does not trickle down from verticalsurfaces.
• Stable to the temperature up to +160 °С.
• Low consumption (500 ml can for 20 m²).
Application instructions
1. Clean the open surfaces of the parts from dirt, rust
and dust.
2. Shake the can.
3. Spray onto the surface at a distance of 20–30 cm.4. VERYLUBE Anticor ML should be applied in one
layer.
5. Use an extension pipe to treat close surfaces.
Note
The ambient air temperature while treating should be +15…20 °С.
Can be used in the engine compartment.
Excess of Anticor ML can be easily removed with Verylube Tar Stain
Remover.
500 mlArt. XB 40129aerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
16/40
8/20/2019 Verylube-catalogue-2013-En_web.pdf
17/40
| 17
Wheel disc purier(for aluminum)
Product designed to clean wheel discs.
Easily cleans wheel discs from contaminations and adds luster to them. Protects from
corrosion. Applied for cleaning any type of wheel disc, including those made of light
aluminum alloys.
Wheel disc purier (for chromium)
Advantages
• Quickly cleans discs from hard-to-remove contaminations, causedby break operation.
• Adds luster to wheel discs.
• Creates a dirt-repellant and anti-corrosion protective lm.
Application instructions
Spray onto the surface of the cold
wheel disc, wash with large amount of
water in 10-15 sec. After cleaning, it is
recommended to treat the cover with
VERYLUBE Conditioner of rubber and
plastic.
Attention!
Please check the effect of the product
on a small part of the disc before
application. Do not apply to units of brake
system, steering system and mounting.
It is not recommended to apply the
product to chromium-plated wheel discs.
In this case use Wheel disc purier (for
chromium).
500 mlArt. XB 40134bottle with
trigger
Product designed to clean chromium-plated wheel discs.
Easily cleans wheel discs from contaminations and adds luster to them. Protects from
corrosion. Applied for cleaning chromium-plated wheel discs.
Advantages• Quickly cleans discs from hard-to-remove contaminations,
caused by break operation.
• Adds luster to wheel discs.
• Creates a dirt-repellant and anti-corrosion protective lm.
Application instructions
Spray onto the surface of the cold wheel disc, wash with largeamount of water in 2-3 min.
500 mlArt. XB 40108
bottle withtrigger
8/20/2019 Verylube-catalogue-2013-En_web.pdf
18/40
Car body products18 |
Lacquer coating polish
Product designed to take care of lacquer coating of a car.
Effective product for cleaning and polishing lacquer coatings of a car. It is applied
universally for glossy lacquer coatings and metallized enamel (metallic lacquer), as well
as for new and faded surfaces.
Advantages
• Refreshes and gives deep shine tolacquer coating. Smoothes out minor
surface irregularities.• Preserves lacquer coating and
provides long-term protection from
environmental impact.
320 mlArt. XB 40024aerosol can
Application instructions
1. Shake the can.
2. Spray a small amount of the product
onto the clean dry surface.
3. Polish with a cloth.
Chrome conditioner
Spray designed to take care of decorative chrome-plated surfaces.
Today's best special product for cleaning and polishing chrome-plated surfaces. Gives a
new appearance to chrome-plated parts of cars, motorcycles and other vehicles.
Advantages
• Removes a dull layer, darkspots and corrosion.
• Refreshes and gives shining tochrome-plated parts.
• Provides a long-term protectionfrom oxidation.
320 mlArt. XB 40022
aerosol can
Application instructions
1. Shake the can.
2. Spray a small amount of the product
onto the surface of the part to be
treated.
3. Polish with a cloth.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
19/40
| 19
Metal polish
Conditioner for rubber and plastic
Product designed to take care of exterior metal parts of a car body.
Today's best product for cleaning and polishing metal parts of the car body. It is applied
universally for steel and aluminum load bearing elements, as well as for parts made of
copper alloys and zinc.
Spray conditioner designed to take care of rubber and plastic articles.
Product designed to restore the original color of rubber and plastic parts.
It is used to treat tires, bumpers, moldings, mirrors, dashboard and other rubber and
plastic parts of cars. It is an effective alternative for washing the underhood space of
an engine. After application parts look as new as if they have just been taken off from
the conveyer.
Advantages
• Gives a bright metal shine to fadedsurfaces and refreshes them.
• Eliminates small surfacesimperfections.
• Protects from environmental attack.
Advantages
• Cleans micro cracks andscratches from dirt and lls
them in.
• Gives original color andshine to rubber and plastics
parts.
• Protects them from fadingand cracking.
320 mlArt. XB 40023aerosol can
320 mlArt. XB 40006
aerosol can
500 mlArt. XB 40106
aerosol can
Application instructions
1. Shake the can.
2. Spray a small amount of the product
onto the surface to be treated.
3. Polish with a cloth.
Application instructions
1. Shake the can.
2. Spray a thin layer onto the surface to
be treated.
3. Wipe off with a cloth.
Note
Surfaces do not
require polishing after
treatment.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
20/40
Compartment care products20 |
Dashboard polish
Product designed to take care of plastic and wooden parts of a car compartment.
Efcient product designed to clean and refresh parts in a car compartment (control panel and other plastics, wooden,
leather and vinyl parts). Efciently cleans the surfaces from contaminations and protects from cracking.
Advantages
• Easily penetrates into the smallest scratches on thesurface of parts and removes dirt.
• Refreshes the appearance of plastics and wood andmakes them shine.
• Gives antistatic properties to the surface, thus, it getsless dirty and dusty.
• Does not leave any greasy lm after use.
• Prevents plastics from cracking and prevents its fadingin the sun.
Application instructions
1. Shake the can.
2. Spray a small amount of the product onto the surface
to be cleaned.
3. Wipe off with a cloth.
Note
Does not require lots of polishing.
Expert's Advice
If with time the shine is gone, wipe again the dashboard
with cloth (without the polisher). The shine will appear
again. with scent
cherry
320 mlArt. XB 40020
aerosol can
500 ml
Art. XB 40120aerosol can
with scentlemon
320 mlArt. XB 40010aerosol can
500 ml
Art. XB 40110aerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
21/40
| 21
Compartment cleaner
Leather care
Compartment upholstery cleaner.
Effective and handy product designed for cleaning car compartment upholstery (natural
and articial fabric, carpeting, plastic, etc). Easily cleans oil spots.
Safe and effective care of leather in a car compartment.
Product designed to take care of natural and articial leather upholstery (seats, doors,
panels etc). Contains castor oil.
Advantages
• Easily cleans the upholstery andremoves oil and grease contaminations.
• Removes grime.
• Restores original appearance, colorand texture of fabric. Bristles up and
straightens bers; gives silky look to
upholstery.
• Absorbs unpleasant smells.
• Gives antistatic properties to upholstery.
Advantages
• Quickly penetrates intoleather structure and removes
contaminations.
• Restores leather elasticity.
• Covers small cracks and gives shineto the nish.
• Gives antistatic properties to thesurface; thus it gets less dusty.
• Gives waterproof and stain repellantproperties to the leather.
•Prevents leather ageing and fading in
the sun.
Application instructions
1. Shake the can.
2. Spray a small amount onto a
sponge.
3. Clean the spots on the
upholstery with formed foam.
Application instructions
1. Shake the can.
2. Spray a small amount of this product
onto the leather surface.
3. Wipe off with a cloth.
Note
Do not use for cleaning
leather articles.
Expert's Advice
For more effective grime removal,
use a clothes brush.
320 mlArt. XB 40013aerosol can
320 mlglossy
Art. XB 40012
mattArt. XB 40032
aerosol can
150 mlglossy
Art. XB 40112
mattArt. XB 40132
aerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
22/40
Compartment care products22 |
Complex foam cleaner for car airconditioners
Product designed to clean and maintain car air conditioners.
It is used for in-place cleaning of air-ways of complicated conguration in the modern
automobile air conditioners. It removes contaminations quickly and easily and provides inow
of fresh air. It has disinfectant properties. It kills fungi and bacteria, thus preventing the risk of
allergies and other respiratory diseases.
Advantages
• Cleans the air conditionerfrom contaminations and
provides an inow of cleanand pure air from the air
conditioner.
• Disinfects the airconditioning system,
eliminates musty odors, kills
fungi and bacteria.
• Forms a bactericide lmon the air conditioner
evaporator and airways.
Application instructions
1. Shake the can.
2. Spray the content into a deector (airway) for cold airof an air conditioner using tube extender, so that the
substance could get onto evaporator.
3. Start the engine in 15–30 minutes and let it idle for 3–4
minutes with an air conditioner fan turned on.
Note
Spray the substance in a well ventilated area or outside when the
engine is turned off and the car doors are open. Contains biologically
active substances.320 mlArt. XB 40016aerosol can
Antibacterial cleaner for carventilation systems
Product designed for antibacterial treatment of car ventilation- and air deodorization
systems.
It is used for ventilation- and air conditioning systems of any type (heating/ventilation,
conditioner, climate control etc.). Prevents the risk of allergies and other respiratory diseases.
Cleans and disinfects systems. Deodorizes air.
Advantages
• Kills fungi and bacteria,eliminates musty odors.
• Deodorizes air.
Application instructions
1. Shake the can.
2. Spray the cleaner for 3-4 seconds into all airways of air
conditioning system (ventilation) of a car.
3. Start the engine in 2–3 minutes and let it idle for 2–3
minutes with an air ventilation system turned on.
Note
Spray the substance when the engine is not operating.
Contains biologically active substances.
As preventive measures, use the product not less than once a month.
320 mlArt. XB 40616
aerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
23/40
| 23Metal conditioner
Verylube Turbo
Metal conditioner for engine.
A completely synthetic concentrated multicomponent product, composed on the basis of the latest discoveries in tribology
and chemistry. It is formulated specially for internal combustion engines. It is used for complex protection of friction parts
of gasoline and diesel engines, including turbo-charged.
Advantages
• Increases engine power.
• Increases compression.• Reduces noise and vibration.
• Decreases oil consumption.
• Improves dynamic characteristics of a vehicle.
• Decreases fuel consumption.
• Improves motor oil properties.
• Protects engine parts from wear.
• Makes cold start easy.
• Reduces harmful exhausts.
Application instructions
1. Pour the conditioner into warmed up engine through
the oil ller neck.
2. Let the engine idle for 3 minutes.
3. The conditioner works during the whole service life of
the oil.
Dosage
125 ml (1 can) for 4 liters of oil.
Technical characteristic
The formula of VERYLUBE TURBO contains carbon
С60 molecules (fullerenes) and aliphatic hydrocarbons
reinforced with halogens.
Note
Optimal concentration: 3% of the oil volume. Overdose up to 50% is
allowed, i.e. up to 4.5% of the oil volume.
The conditioner has gentle detergent properties that remove carbon from
piston rings.
To achieve the maximum effect — use regularly with every oil change.
125 mlArt. XB 40060can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
24/40
Metal conditioner24 |
Metal conditioner
Multilevel protective formula against wear and overloads of the automobile units.
The product is designed for creation of special conditions for operation of engine units (transmission, hydraulicsystem) due to which an effective multilevel system of wear and overload protection will be formed.
The metal conditioners are formulated on the base of a fully synthetic polyhydric polymer and a well-balanced
package of antioxidant and antiscoring additives. The polymer molecules are highly resistant to destructive impact of
local overloads in the friction zone due to covalent interatomic bonds which allow eliminating metal-to-metal contact in
the friction zone within the entire lifespan of the oil.
Advantages
• Protects against wear and overloads
• Increases engine power and driving
moment• Increases service life of subassemblies
• Reduces noise and vibration
• Reduces the amount of exhaustemissions
Metal conditioner for hydraulic system
1. Shake the can.
2. Spray the product through the tube-nozzle into the
oil ller neck (vent of the oil gage rod) of automatic
transmission or mechanism of the power steering
booster.
3. Drive the car in normal mode without any restrictions.
Nominal dosage125 ml (1 can) for 8 L of hydraulic uid.
20ml (spray during 15-20 seconds) for 1 L of iud.
Metal conditioner for transmission
1. Shake the can.
2. Spray the product through the tube-nozzle into the
oil ller neck (oil measuring hole) of mechanical
transmission, axle gearboxes or transfer cases.
3. Drive the car in normal mode without any restrictions.
Nominal dosage
125 ml (1 can) for 2 L of transmission oil.75 ml (spray during 1 minute) for 1 L of oil.
150 mlArt. XB 40261
aerosol can
Forengine
150 mlArt. XB 40262
aerosol can
Fortransmission
150 mlArt. XB 40264
aerosol can
For hydraulicsystem
Application
Metal conditioner for engine
1. Pour the product into the oil ller neck of
the warmed up engine at the rate of 3-6%
from the oil system nominal value.
2. Provide the engine operation in idle mode
during 3 minutes.
3. Drive the car in normal mode without any
restrictions. The resource of metal conditioner is enough
for the whole period of oil exploitation.
Nominal dosage
125ml (one bottle) for 4 L of oil.
24 |
8/20/2019 Verylube-catalogue-2013-En_web.pdf
25/40
Insect trace remover
Concentrate for intensive windshields cleaning.
Easily and quickly cleans glass, metal, paint, plastic, as well as nickel- and chrome-plated parts
of a car. Specially designed to remove organic contaminations which contain chitin.
Advantages
• Removes insect traces.
• Dissolves fresh and oldspots of wood resin and tar.
Removes traces of poplar budsand sap of plants.
• Removes lime spots.
• Easily cleans windshieldsfrom contaminations (road
dirt, oil coating, etc.) owing to
improved detergent properties.
Applicationinstructions
VERYLUBE Insect trace
remover (aerosol).
1. Shake the can.
2. Spray onto the surface to
be cleaned.
3. Wipe off with a cloth
(sponge) in 5–10
seconds.
VERYLUBE Insect trace
remover (sachet).
Add the contents of a sachet
into a windshield washer
reservoir at a ratio 1 sachet
for 3 liters of uid.
Note
If strongly
contaminated, the
dosage should be
doubled.
320 mlArt. XB 40004
aerosol can
500 mlArt. XB 40404bottle withtrigger
20 mlArt. XB 40104packet
Red Penguin
250 mlArt. XB 50006two-chamberplastic bottle
Concentrate for intensive windshields cleaning.
Thanks to improved detergent properties, it easily cleans windshields from insect traces
and other contaminations (road dirt, oil coating, poplar buds etc.).
Advantages
• Quickly removesinsect traces and other
contaminations.
• Concentrate product,economic and handy in
application.
Application instructions
Open the cover. Fill the dozer with the uid,
squeezing smoothly the main bottle. Pour the uid
into the windshield washer reservoir (mix it with
water).
Dosage:
25 ml of the uid for 3 L of water.
| 25Glass care products
8/20/2019 Verylube-catalogue-2013-En_web.pdf
26/40
Glass care products26 |
Antirain
Spray designed to improve water-resistant properties of windshields surfaces.
Creates a thin hydrophobic lm on the glass. After treatment the water drops do not
spread on the glass, but quickly run down improving visibility. Increases signicantly the
glass limiting wetting angle.
Advantages
• Improves visibility during rainor sleet.
• Prevents freezing of windshields.
• Indispensable if windshield wipers are out of order.
Application instructions
1. The treatment should be made in dry weather.
2. Shake the can.
3. Spray Antirain onto the clean dry external
surface of the windshield, mirrors and lights.
4. Polish glass with a cloth.
320 mlArt. XB 40027
aerosol can
Note
Recommended for regular use (once
per 3–4 weeks).
Ice-breaker
Frost remover and lock defroster.
It is used to remove frost from the windshields. It also quickly removes ice from
mirrors, paint, chrome-plated, plastic, and rubber parts. Efciently defrosts door
locks.
Advantages
• Quickly defrosts and efcientlyremoves ice from car windows.
• Thaws out ice-covered car
surfaces and locks.• Removes ice and frozen rough
layer of snow from mirrors,
paint, chrome-plated, plastic and
rubber parts.
Application instructions
VERYLUBE Ice-breaker (aerosol)
To remove ice.
1. Shake the aerosol can.2. Spray onto the frozen surface, wait
10–15 seconds, and remove the
thawed ice with a scraper or a sponge.
320 mlArt. XB 40017aerosol can
550 mlArt. XB 40063bottle withtrigger
10 mlArt. XB 42263tube
To defrost door locks.
1. Shake the aerosol can.
2. Spray into the keyhole. The lock will
be defrosted in 1 minute.
VERYLUBE Ice-breaker (tube)
Squeeze the contents of the tube into
the keyhole. The lock will be defrosted in
1 minute.
8/20/2019 Verylube-catalogue-2013-En_web.pdf
27/40
| 27
Antifog
Spray designed to prevent steaming up on windshields.
This efcient product prevents moisture condensation on the internal surfaces of
windshields. Allows avoiding the undesirable effect of window steaming in chilly and
rainy weather.
Advantages
• Prevents water condensation on windshields.
• Does not let moisture gather into tiny
drops keeping windshields clean andtransparent.
Application instructions
1. Shake the can.
2. Spray Antifog onto the glass surfaces.
3. Wipe the glass with a cloth.
320 mlArt. XB 40028aerosol can
Note
Can be applied to a steamed up window.
Recommended for regular use (once per 3–4
weeks).
Auto Shampoo
Concentrate for intensive car cleaning.
Thanks to complex formula of surface-active substances (tensides), it easily and absolutely
safely washes off all kinds of contamination from a car body.
Advantages
• Quickly dissolves dirt on thecar body surface.
• Can be used for cleaningpain surfaces of all types.
• Does not leave stains.
• Safe for rubber and plastic.
• Handy application.
Application instructions
Open the cover.
Fill the dozer with the shampoo,
squeezing smoothly the bottle.
Add it into water and make foam
Dosage:
25 ml of shampoo for 5 L of water.
250 mlArt. XB 50007two-chamberplastic bottle
8/20/2019 Verylube-catalogue-2013-En_web.pdf
28/40
Application instructions
1. Shake the can.
2. Spray onto the treated surface from the distance of10–20 cm.
3. Use the nozzle for hard-to-reach places.
Lubricants
Any Way
Universal penetrating spray lubricant for different mechanisms. Contains revitalizant.
It is designed for all types of units and mechanisms, weapons, tools and equipment. AnyWay lubricant restores mobility
of units and parts; it can penetrate easily and quickly into the rusted or jammed joints, lubricates and separates them.
This lubricant efciently protects contact places from corrosion. It is neutral to rubber, wood, plastics, lacquer coating
and bluing. All-purpose helper!
Advantages
• Lubricates assembly parts and restores friction surfacesusing unique XADO technology.
• Protects from rust and corrosion under conditions of
increased humidity, contamination and action of hostileenvironment (saline, acid solution and alkali).
• Displaces moisture and dries the contacts of electricequipment.
• Serious barrier for water and moisture.
• Prevents electrical leaks and shorts.
• Defrosts door locks and restores their mobility, protectsthem from freezing and corrosion.
• Cleans off contamination, easily dissolves grease andtar spots; removes glue residues, insect traces and
prevents adhering of dirt and dust.
• Takes care of weapon parts and gently removes the gunpowder scale.
• Preserves parts and protects them from corrosion andoxidation.
150 mlArt. XB 40001аerosol can
300 mlArt. XB 40201аerosol can
400 mlArt. XB 40101аerosol can
28 |
8/20/2019 Verylube-catalogue-2013-En_web.pdf
29/40
Universal penetrating lubricantUniversal penetrating spray-lubricant. “Liquid key”.
The lubricant penetrates easily and quickly into threaded and other joints, returns
mobility to rusted parts. It is recommended for application at service stations, garages,
shops, in household and industrial environments. It can lubricate any friction surface of
the parts.
Advantages
• Removes oil and grease contaminations from car bodysurfaces.
• Protects parts from corrosion and oxidation.
• Defrosts door locks and prevents their freezing.
• Displaces moisture and eases the engine start in damp weather.
Application instructions
1. Shake the can.
2. Spray a thin layer onto a work surface
(part, joint).
| 29
Application instructions
1. Shake the can.
2. Spray the contents onto the clean surface of the
part (joint).
Any Way
Consistent lubricant with penetrating effect and the revitalizant.
It is designed for all types of units and mechanisms, weapon, tools and equipment, which require long-lasting lubricating
effect. It restores the mobility of units and parts; it can penetrate easily and quickly into the rusted or jammed joints,
lubricates and separates them. Lubricates reliably and protects from corrosion and oxidation.
Advantages
• Reliably lubricates with a thick grease layer.
• Easily penetrates into joints.
• Possesses enhanced anticorrosive properties, provideslong-term preservation of the mechanisms if stored
outdoors.
• Protects from penetrating of water, dust, dirt.
• Owing to revitalizant, it compensates wear and prolongslife span of the mechanisms by 2-4 times.
320 mlArt. XB 40003
аerosol can
500 mlArt. XB 40103
аerosol can
150 mlArt. XB 40203
аerosol can
150 mlArt. XB 30001
аerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
30/40
Lubricants30 |
Lithium universal grease
Universal consistent grease with EP (Extreme Pressure) formula.
It is applied to lubricate and protect assemblies and joints operating under high thermal and mechanical loads. It isused to lubricate friction and frictionless bearings of various assemblies and mechanisms. Thanks to ЕР (Extreme
Pressure) complex, it protects mechanisms from destructive wear while operating and when the use of regular lithium
greases is not permitted.
Advantages
• Possesses high mechanical and chemical stability andkeeps protective and anti-wear properties even after
prolonged mechanical and thermal loads.
• Owing to the strong adhesive properties, it remainson the lubricated surfaces even under the action of
vibration and high rotation speeds.
• Water-resistant and can be used in assembliesoperating in contact with water.
• Forms a good isolation and prevents (unit) bearingcontamination.
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached.
Manual application.
Eliminate the previous grease and ll 1/2 of bearing
volume (unit) with Lithium universal grease.
Grease in aerosol can.
1. Shake the can.
2. Spray a thin layer of the grease onto cleaned part.
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Efcient for assemblies with the rotation speed up to 10,000 rpm.
5 mlpacket from foil-clad cellophane
125 mlArt. XB 30250plastic tube
450 mlArt. XB 30050grease guncartridge
320 mlArt. XB 40018аerosol can
NLGI 2 (ASTM D217)
ISO-L-XBCEB 2 (ISO 6743-9)
KP2K-20 (DIN 51502)
Requirements
8/20/2019 Verylube-catalogue-2013-En_web.pdf
31/40
| 31
Lithium complex grease
Universal lithium consistent grease with metal conditioner.
It is used to lubricate and protect assemblies and joints operating under heavy thermal and mechanical loads. It isrecommended for automotive assemblies and bearings as well as for industrial equipment. Due to the metal conditioner,
the grease signicantly reduces friction losses and protects the parts from wear.
Advantages
• Provides reliable lubrication of assemblies andmechanisms under overloads and high temperatures
for a long period of time. Signicantly decreases
friction losses and effectively protects parts from wear.
Reduces energy consumption.
• It is used in assemblies with single grease lling for the whole period of operation.
• It prevents formation of rust and corrosion. Owing tostrong adhesion, it remains on the lubricated surfaces
even with strong vibration and high rotation speeds.
• Possesses excellent moisture and dust protectionproperties.
125 mlArt. XB 30252plastic tube
450 mlArt. XB 30052grease guncartridge
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached.
Manual application.
Eliminate the previous grease and ll 1/2 of bearing
volume (unit) with Lithium complex grease.
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Efcient for assemblies with the rotation speed up to 10,000 rpm.
NLGI 2 (ASTM D217)
ISO-L-XBDIB 2 (ISO 6743-9)
KP2N-30 (DIN 51502)
Requirements
8/20/2019 Verylube-catalogue-2013-En_web.pdf
32/40
Lubricants32 |32 |
Lithium grease for CV joints
Consistent grease with molybdenum disulde (MoS2) for constant velocity joints.
It is recommended for application in constant velocity joints, assemblies and bearings of vehicles as well as industrialequipment. It contains pure superne molybdenum disulde (MoS2) owing to which it effectively protects assemblies
and bearings operating under peak and/or oscillatory loads.
Advantages
• Special grease for constant velocity joints.
• Effectively protects assemblies and bearings operatingunder peak and/or oscillatory loads.
• Possesses high mechanical and chemical stability,keeps protective and anti-wear properties even afterprolonged mechanical and thermal loads.
• Owing to strong adhesion, it remains on the lubricatedsurfaces even under the action of vibration and high
rotation speeds.
• Water-resistant and can be used in assembliesoperating in contact with water.
• Forms a good isolation and prevents bearings fromcontaminations.
Application instructions
With pressurized application.
Add the grease through the zerk until desired grease
volume is reached
Manual application.
Eliminate the previous grease and ll 1/2 of bearing
volume (unit) with Lithium grease for CV joints.
Note
Compatible with automotive and industrial lithium greases of all types,
and can be mixed with them in any proportion.
Applied for assemblies with the rotation speed up to 10,000 rpm.
125 mlArt. XB 30251plastic tube
450 mlArt. XB 30051grease guncartridge
NLGI 2 (ASTM D217)
ISO-L-XСCEB 2 (ISO 6743-9)
KPF2N-25 (DIN 51502)
Requirements
8/20/2019 Verylube-catalogue-2013-En_web.pdf
33/40
| 33
Advantages
Silicon lubricant
Universal dense silicon spray lubricant.
It lubricates and penetrates into joints made of various materials (metal, plastics, rubber, leather and wood in anycombination). It eliminates creaking of plastic panels, slideblocks and belts. It restores the easiness of lock work. It is
used as a preserving anticorrosion substance for cables, control rods and levers. It possesses perfect water resistant
properties due to the formation of multi-molecular layer of silicon. It prevents plastic and rubber parts from cracking on
the sun.
•Cleans and restores plastic, vinyl and rubber surfaces.
• Gives shine and polishes control panels, restorestheir original color and appearance; restores the
appearance of vinyl body upholstery and takes care of
the rubber tire covers.
• Restores the elasticity of seals.
• Prevents adhesiveness of rubber to metal; restoreselasticity of gaskets.
• Protects from corrosion and sunlight.
• Displaces moisture and dust, dries electrical contactsand forms the antistatic lm.
• Prevents freezing and ice-formation of rubber sealingof vehicle doors and hatches.
• Separates and protects parts during industrialpunching and gas welding.
Application instructions
1. Shake the can.
2. Spray a thin layer onto a work surface (part, joint).
3. If necessary, wipe it with a napkin.
4. 4. In case of severe contaminations, repeat the
treatment.
150 mlArt. XB 40205аerosol can
320 mlArt. XB 40005аerosol can
500 mlArt. XB 40105аerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
34/40
34 |
Assembly grease paste
Brake Caliper Grease
Assembly grease paste for easy assembling and disassembling of joints which
operate at high temperatures.
Grease paste designed to assemble and disassemble the units which operate at high
temperatures for a long period of time. Used for anges and thread pieces of nozzles of
the exhaust system, screw joints of the turbo compressor body, sparkplug threads etc.
High-temperature grease for guide ngers of brake caliper sliding carriage.
Special high temperature grease applied to prevent sticking and seizing of brake pads
on guide ngers of sliding carriage.
Advantages
• Makes joint assembling easy.
• Makes easy further disassembling of joined parts which operate at high temperatures for long period
of time.
• Has separating and lubricating effect.
• Prevents burning and sticking of parts, and formationof heat scale.
• Resistant to high loads.
• Efcient within the temperature range –35…+1,100 °С.
Advantages
• Provides accurate operation of the whole sliding carriage mechanism,
absolute abutment of brake pads and
quick unbraking of a brake disc at the
end of braking.
• Prolongs the service life of the wholebraking system of a vehicle.
• Eliminates noise and creaks whenbraking.
• Resistant to high loads.
• Has a wide temperature range ofapplication: –35…+400 °С
Applicationinstructions
1. Shake the can.
2. Spray a thin layeronto the clean part’s
surface.
Application instructions
1.Twist out the guide ngers of a brake
caliper.
2. Shake the can.
3. Apply a thing layer of the grease.
4. Assemble the unit.
320 mlArt. XB 40021аerosol can
320 mlArt. XB 40019
аerosol can
Note
Use when replacing brakepads or next maintenance
work.
Products for locks
8/20/2019 Verylube-catalogue-2013-En_web.pdf
35/40
| 35
Lock lubricant
Penetrating spray lubricant for automobile locks.
Lubricates and ensures easy operation of the lock mechanism.
Removes moisture from the parts’ surfaces and protects them from corrosion.
Application instructions
1. Shake the can.
2. Spray the content (2–3 sec.) into the keyhole.
50 mlArt. XB 40030
аerosol can
Lock de-icer
Aerosol product designed to defrost automobile locks.
Quickly unfreezes the iced parts of the lock mechanism and restores their mobility.
Defrosts ice and removes moisture from the surface of the parts, prevents their further
freezing.
Application instructions
1. Shake the can.
2. Spray the content (2–3 sec.) into the keyhole. The lock will thaw in
a minute.
It is recommended to use the product every 2 weeks in winter.
50 mlArt. XB 40031аerosol can
Lubricating lock de-icer
Universal care product for automobile locks.
Quickly defrosts the iced parts of the lock mechanism and recovers their mobility.
Lubricates the parts and protects them from corrosion.
Application instructions
1. Shake the can.
2. Spray the content (2–3 sec.) into
the key-hole.
50 mlArt. XB 40033
аerosol can
320 mlArt. XB 40133
аerosol can
8/20/2019 Verylube-catalogue-2013-En_web.pdf
36/40
Gun cleaning grease
Gun cleaning grease-spray for constant use. Contains revitalizant.
It is used to clean and lubricate the rearms. It provides fast and easy cleaning of small bore and large caliber ried
and smooth bore arms of all types (hunting, sporting, ghting and antique ries). It is recommended for everyday care
of arms with frequent shooting (in a shooting range or during hunting). It provides a reliable protection from corrosion.
Advantages
• Quickly displaces soiling from nooks of breechmechanisms and triggers.
• Special cleaning components of the grease can easilydissolve gunpowder scale in the barrel bore.
• Effectively lubricates threaded, rotary and pinning joints and protects them from corrosion.
• Guarantees perfect operation of the arms.
• Owing to revitalizant, the grease keeps the surface ofthe barrel bore in a perfect condition.
Application instructions
1. Shake the can.
2. Spray onto all parts and mechanisms of the arms.
3. Clean the arms.
Note
Does not contain alkali, neutral to plastics, wood, painted and
lacquered surfaces and bluing.
Does not require to be wiped dry.
When preparing the arms for a long-term storage, it is advised to use
VERYLUBE Gun conserving crease.
75 mlArt. XA 40003аerosol can
500 mlArt. XB 40903аerosol can
500 mlArt. XB 41903aerosol can with2-position spray
36 | Firearms' care products
8/20/2019 Verylube-catalogue-2013-En_web.pdf
37/40
| 37
Gun conserving grease
Gun conserving grease-spray for conserving, cleaning and lubricating the arms before storage. Contains
revitalizant.
It provides reliable protection of the arms from corrosion even if stored for a long time outdoors. It is used for a small bore
and large caliber ried and smooth bore arms of all types (hunting, sporting, ghting and pneumatic). It is used to take
care of arms after shooting and prepare them for storage.
Advantages
• Helps to prepare the arms for storage quickly.
• Possesses high penetrating ability and gets to all partsof the arms.
• Special inhibiting components of the grease neutralizeaggressive actions of the scale particles left after
cleaning.
• Possesses prefect low-temperature properties,provides the mobility and smoothness of the
mechanism operation at the ambient temperature up
to –60 °С.
• Thanks to the revitalizant, it keeps the surface of thebarrel bore in a top condition.
Application instructions
1. Shake the can.
2. Spray a thin layer onto the work surface (part, joint).
3. If necessary, wipe with a napkin.
4. If heavily contaminated, repeat the treatment.
75 mlArt. XA 40004аerosol can
500 mlArt. XB 40904аerosol can
500 mlArt. XB 41904aerosol can with2-position spray
8/20/2019 Verylube-catalogue-2013-En_web.pdf
38/40
Firearms' care products38 |38 |
Cleaning foam for gun barrels
Safe product for cleaning the internal surfaces of the barrel bore from copper residues.
Applied to ried and smooth-bore arms of any caliber. Foam cleaning method of barrels is approved by NATO.
Due to its high efciency and safety, the foam cleaning method exceeds barrel cleaning methods with special oils and
wire brush.
Advantages
• Quickly (15-30 min) and easily removes soft metalresidues from the inner surface of the barrel bore.
• Acts safely; contains special components inert tothe metals of the barrel (breech-block) surfaces;
selectively dissolves copper (brass) residues.
• Can be used for regular arms cleaning (from scale andgun powder gases).
• Environmentally friendly, non toxic.
Application instructions
1. Let the gun cool down to the room temperature,
disassemble it for cleaning. Close the barrel breech
(with a rag, false cartridge etc.).
2. Shake the can.
3. Spray the content into the barrel bore till the foam
appears from the muzzle.
4. Wait for 15-30 min, then remove the foam remains
with a clean rag. (As a result of the reaction with
copper compounds the foam becomes blue).
5. Repeat the foam cleaning if necessary.
6. After the cleaning, treat the barrel with the grease
(VERYLUBE Gun cleaning or Gun conserving
grease).
One can (500 ml) is enough for cleaning of Win. 308
barrel ( 7.62 ml) for approximately 100 times.
500 mlArt. XB 40906аerosol can
500 mlArt. XB 41906aerosol can with2-position spray
8/20/2019 Verylube-catalogue-2013-En_web.pdf
39/40
8/20/2019 Verylube-catalogue-2013-En_web.pdf
40/40
Head ofce: 4, 23 Augusta Lane,
Kharkov, 61103, Ukraine
Tel.: +38 (057) 717-55-55, 717-44-44,
fax +38 (057) 714-11-11.
www.xado.com, info@xado.сom
www.verylube.com
The manufacturer has the right to change
the design of the products’ packaging. All
rights to the presented trade marks and
logos belong to their legal owners. Style,
design and contents are the object of
copyright of XADO Ltd. and protected by law.
Reprinting and other application of materials
without written authorization by XADO Ltd.
is prohibited and involves responsibility
according to the existing legislation.