VI. CLX-6240FX & CLX-6200FX series Firmware VI. CLX-6240FX & CLX-6200FX series Firmware.

transcript

VI. CLX-6240FX & CLX-6200FX series Firmware

Revision History

• V0.1 : 2007.06.20 : Initial Release – Joong Mok Lee

• Revision : to Now - Won Young Chi

Overview - I• Model

– CLX-6200ND : DADF, HDD option, wireless LAN option– CLX-6200FX : ADF, FAX– CLX-6210FX : DADF, FAX, HDD option, wireless LAN option– CLX-6240FX : DADF, FAX, HDD, wireless LAN option

• Print method– Single-pass printing (Y->M->C->K)

• Printing speed– CLX-62x0 20/20 ppm (Color/Mono)– CLX-6240 20/20 ppm (Color/Mono)

• Resolution in printing (PC printing)– Best mode 1200 x 1200 dpi– Normal mode 1200 x 600 dpi– Draft mode 600 x 600 dpi

• Resolution in printing (Copy)– Default 600 x 600 dpi– Platen photo 1200 x 1200 dpi

• Duplex mode support

Overview - II• Supported I/O port

– USB, Network

• CRUM

– C/M/Y/K Toner, PTB

• Memory size (default)

– CLX-62x0 : 128MBytes

– CLX-6240 : 256MBytes

• Panel

– 2- line LCD panel support

– Ten key, speed dial support

– STOP, Start (Color/Mono) Key

Overview - III

• CPU (CLX-62x0/CLX-6240)

– Type : CHORUS3/SPGPXm (ARM 920EJ /PMC 7065)

– Speed : 300MHz/533MHz

– Bus speed : 120MHz/ 120MHz

– One chip solution (HPVC, I/O, JBIG, network …)

• Real-Time OS (CLX-62x0/CLX-6240)

– pSOS (V2.5) / VxWorks 5.5.1

• Network configuration

– Embedded Network

ROM Image• ROM image

• ROM release

– Boot image

– ROM image (except boot image)

CLX-62x0 CLX-6240

ROM Size 16.0M bytes 16.0M bytes

Boot 256K bytes 256K bytes

Kernel 10M bytes 12M bytes

Emulation 6M bytes 6M bytes

Network 8M bytes 10M bytes

Demo Page 2M bytes 2M bytes

F/W Upgrade

• USB and Network port are used to F/W upgrade

• Network applications (SWAS, SWS) can be used for network port upgrade

• Notice : In special mode upgrade, kernel waste header information for CLX-62x0/CLX-6240. You have to check F/W ROM file with MFP set (This mode is ONLY service mode, not user mode)

• F/W Upgrade using USB Port– Make sure connecting Printer to the

computer with a USB cable

– Upgrade in Ready mode• Send ROM image file via USB cable

in Ready mode– Upgrade in Special mode

• Power ON with pressing ‘STOP key’ two times

• Change LCD message ‘Wait Image’• Send ROM image file via USB cable

F/W Upgrade – using button

F/W Upgrade – using SWS• F/W upgrade using SWS(SyncThru Web Service)

– Home -> Maintenance -> Firmware Upgrade

F/W Upgrade – using SWAS1. F/W upgrade using SWAS(SyncThru Web Admin Service)

– Home Maintenance

F/W Upgrade - using SWAS2. F/W upgrade using SWAS(SyncThru Web Admin Service)

– Firmware Upgrade Upgrade (check device using IP address)

– Maintenance -> Firmware upload (register firmware)

– Maintenance -> Firmware Upload (upload firmware)

– Maintenance -> Firmware Upload (confirm uploaded firmware)

F/W Upgrade - VI2. F/W upgrade using SWAS(SyncThru Web Admin Service)

– Maintenance -> Firmware Upgrade -> Upgrade (choose firmware)

F/W Upgrade - VI2. F/W upgrade using SWAS(SyncThru Web Admin Service)

– Maintenance -> Firmware Upgrade -> Upgrade (choose firmware)

– Maintenance -> Firmware Upgrade -> Upgrade

– Maintenance -> Firmware Upgrade -> Upgrade (Done)

Information print

• Demo page

– Press OK Key for 2sec– Blinking Green LED (status LED)

• System Configuration page

– Menu System Setup report configuration ‘yes’– Blinking Green LED (Status LED)

• Network Configuration page

– Menu System Setup report Network Info. ‘yes’– Menu Network Network Info. ‘yes’– Blinking Green LED (Status LED)

• Total Page Count (Color/Mono)• Page Count (C/M/Y/K)• Fuser Life• Toner Remains Percent (C/M/Y/K) • Transfer Belt Life• Tray1/Tray2 Roller Life• MP Roller Life• Model ID (C/M/Y/K/PTB)

• Serial No. (C/M/Y/K/PTB)

• Product Date (C/M/Y/K/PTB)• Last Used Date• First Installed Date• ADF Scan Page Count• Platen Scan Page Count

• Consumables Information (C/M/Y/K)

Supplies Information

Status Monitor

• Display in Status Monitor window• Consumables Life Errors

– Toner Low– Toner empty– Replace Toner Cartridge

– Replace transfer belt soon– Replace transfer belt– Replace fuser soon– Replace fuser– Replace imaging unit soon– Replace imaging unit– Replace Pickup (tray1/tray2) roller

• Need to replace those items when replace error is indicated

Consumable Unit ActivityToner Empty Status should be selected option as below:- Color : Stop, Continue, Mono Only- Mono : Stop, Continue

*Stop all printing is not allowed.*Continue all printing is allowed until toner cartridge is exhausted.*Mono Only color printing data is wasted. Mono printing only allowed.

Invalid/Install Toner Status- Color/Mono/PTB : all printing operation is not allowed.

Exhausted Toner Status (After Empty Status)-Color/Mono : all printing operation is not allowed.

Lily (CLX-62x0)Lily (CLX-62x0)Part. II Engine F/WPart. II Engine F/W

EDC Mode• Method to enter

• Power – On the printer, and wait until the “READY” message appearing on LCD Panel.

• Push button like next time “Menu -> Stop -> Left arrow -> Back -> OK -> Right arrow”

• “COMPONEMT TEST Press Menu Key”

③ ④⑤ ⑥

• Keys

Key DescriptionMenu Move to the top menu

Left Arrow Move test item

OK Start testing or select Sub-item

Right arrow Move test item

Back Move upper menu

Stop Stop testing

• EDC Menu– 0. Cover Status

Item DescriptionTop Cover When a top cover opened, “Open” message display LCD. If

the top cover closed, ”Closed” message display LCD

Tray2 Door When a tray2 door opened, “Open” message display LCD. If the tray2 door closed, ”Closed” message display LCD

Cont.– 1. Sensor Status

Item DescriptionRegi. Sensor If actuator is checked by sensor, "Without Paper" message will be displayed. if

not, "With Paper" will be.

Exit Sensor If actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be.

MP Empty If paper exists in the MP tray, "With Paper" will be displayed. If not, "Without Paper" will be.

T1 Paper Empty If paper exists in the 1st tray, "With Paper" will be displayed. If not, "Without Paper" will be.

T2 Paper Empty If paper exists in the 2nd tray, "With Paper" will be displayed. If not, "Without Paper" will be.

Rev. Swing Sensor If actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be.

Rev. Exit Sensor If actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be.

– 2. Motor Test

Item Description

Main Mtr Nor. If “OK” key is pushed after “ON” displayed, motor will be run. Main motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Dev Mtr Nor. If “OK” key is pushed after “ON” displayed, motor will be run. Dev motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Fuser Mtr Fwd. If “OK” key is pushed after “ON” displayed, motor will be run forward. Fuser motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Fuser Mtr Bwd. If “OK” key is pushed after “ON” displayed, motor will be run Backward. Fuser motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

T2 Feed Motor If “OK” key is pushed after “ON” displayed, motor will be run. T2 feed motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Reverse Mtr If “OK” key is pushed after “ON” displayed, motor will be run. Dev motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

– 3. Fan Test

Item Description

Fuser Fan If “OK” key is pushed after “ON” displayed, fan will be run. Fuser fan will auto - stop after 5 seconds and ”OFF” message will be displayed.

SMPS Fan If “OK” key is pushed after “ON” displayed, fan will be run. SMPS fan will auto - stop after 5 seconds and ”OFF” message will be displayed.

LSU Fan If “OK” key is pushed after “ON” displayed, fan will be run. LSU fan will auto - stop after 5 seconds and ”OFF” message will be displayed.

Reverse Fan If “OK” key is pushed after “ON” displayed, fan will be run. Reverse fan will auto - stop after 5 seconds and ”OFF” message will be displayed.

Cont.– 4. Clutch/Sol.

Item Description

T1 P - up Clutch When “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed.

T2 P - up Clutch When “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed.

(when SCF is not installed, “not installed” message will be displayed )

MP P - up Clutch When “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed.

K Dev. Clutch When “OK” key is pushed after ”ON” message displayed, clutch turn on. K - clutch will be turn off after 5 seconds and ”OFF” message will be displayed.

– 5. Fuser Ctrl

Item Description

Fuser1 Control Fuser 1 on and off. “ON” is selected, fuser will be active and display the fuser temperature [XXX] but “OFF” is selected, fuser will be stop and [0] display

Fuser2 Control Fuser 2 on and off. “ON” is selected, fuser will be active and display the fuser temperature [XXX] but “OFF” is selected, fuser will be stop and [0] display

Fuser Temp.A Fuser1 temperature displayed on LCD (example: [251] )

Fuser Temp.B Fuser2 temperature displayed on LCD (example: [251] )

– 6. LSU Control

Item Description

LD Power Y When “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds

LD Power M When “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds

LD Power C When “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds

LD Power K When “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds

LSU Motor If “OK” key is pushed after “ON” displayed, motor will be run. LSU motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Cont.– 7. DEV Control

Item Description

Charger If “OK” key is pushed after “ON” displayed, Charger voltage will be turned on.

Dev DC Y If “OK” key is pushed after “ON” displayed, Dev DC Y will be turned on.

Dev DC M If “OK” key is pushed after “ON” displayed, Dev DC M will be turned on.

Dev DC C If “OK” key is pushed after “ON” displayed, Dev DC C will be turned on.

Dev DC K If “OK” key is pushed after “ON” displayed, Dev DC K will be turned on.

Dev AC Y If “OK” key is pushed after “ON” displayed, Dev AC Y will be turned on.

Dev AC M If “OK” key is pushed after “ON” displayed, Dev AC M will be turned on.

Dev AC C If “OK” key is pushed after “ON” displayed, Dev AC C will be turned on.

Dev AC K If “OK” key is pushed after “ON” displayed, Dev AC K will be turned on.

Dev TR Y If “OK” key is pushed after “ON” displayed, Dev TR Y will be turned on.

Dev TR M If “OK” key is pushed after “ON” displayed, Dev TR M will be turned on.

Dev TR C If “OK” key is pushed after “ON” displayed, Dev TR C will be turned on.

Dev TR K If “OK” key is pushed after “ON” displayed, Dev TR K will be turned on.

P Charger If “OK” key is pushed after “ON” displayed, Paper Charger will be turned on.

– 8. Reset Param

Item DescriptionReset Color Reg “YES” is Selected, reset color registration starts.

( Take care of this menu because all color regi. data is initialized.)

– 9. PrintTest

Item DescriptionPattern Print “YES” is Selected, pattern printing starts.

Error list and recovery• Operating Error

– Paper Jam

• MP(Tray1, Tray2) Paper Jam0

– When feed sensor is not checked in limit-time after Pick- up

– Right Cover Open /Close (check Feed Sensor and Pick-up solenoid)

• Paper Jam1 Open/Close Door

– When exit sensor is not checked in limit-time after Feed - In

– Right Cover Open-> remove the paper-> cover close

(check Feed Sensor , Exit sensor and fuser motor)

• Paper Jam2 Check Inside

– When exit sensor is not checked in limit-time after Exit-In

– Right Cover Open-> remove the paper-> cover close

(check the exit sensor)

• Duplex Jam0 Check Inside

– When Feed sensor is not checked in limit-time after Exit-Out

• Reverse Jam0 Check Inside

– When rev. Swing sensor is not checked in limit-time after Exit-In

• Reverse Jam1 Check Inside

– When rev. Exit sensor is not checked in limit-time after Swing-Out

Cont.– Cover Error

• Cover Open : Install Transfer Belt message is toggled.

– When right cover is opened or PTB (Paper Transfer Belt) is not installed

– Check that PTB is installed

– Check Right-cover switch, and PTB connector

– Cassette Out Error

• Tray1(Tray2) Cassette Out

– When Tray1- Cassette is out.

– When tray is dedicated Tray2 in printer – driver and Tray2- Cassette is out.

– Paper Empty / Paper Mismatch

• MP(Tray1, Tray2) Paper Empty

– When dedicated-tray is empty

• Load A4 In MP(Tray1, Tray2)

– When paper dedicated in driver is different with paper in tray.

– Push the ”Stop” key , and documents will be printed continuously

Cont.• Service Call error

– LSU Motor Error Cycle Power• When lock signal of LSU motor is not checked• Check LSU and Main board (check Connector)

– OPC Motor Locked / Deve Motor Locked • When lock signal of BLDC motor is not checked• Check Motor and Main board (check Connector)

– Fuser Error• Low Heat Error Cycle Power

– Fuser temperature is not reached at target temperature in limited time.• Over Heat Error Cycle Power

– When Fuser temperature is more than a over- heat temperature• ADC Slope Error Cycle Power

– Fusing Unit is not heated• Thermistor Open/Short Cycle Power

– Thermistor level is not normal

• Check Thermistor is not connected , Thermistor is dirty , thermostat is opened

– Outer (Inner) Temp. Error Cycle Power

• Temp. Sensor- level is not normal

– When color Regi. is not corrected

• First , Check Toner-Density

• Second, Check scratch of PTB.

• Consumables

– Install Cyan (Magenta, Yellow, Black) Toner

– Install Transfer Belt

• When CRUM Interface is abnormal

• Extract Consumables from the Printer, and push consumables to the printer again.

– Invalid Cyan (Magenta, Yellow, Black) Toner

– Invalid Transfer Belt

• When CRUM Interface is abnormal

• Extract Consumables from the Printer, and push consumables to the printer again.

The end

VI. CLX-6240FX & CLX-6200FX series Firmware VI. CLX-6240FX & CLX-6200FX series Firmware.

Documents