Date post: | 04-Apr-2018 |
Category: |
Documents |
Upload: | alexandru-ionut-apostu |
View: | 218 times |
Download: | 0 times |
of 37
7/29/2019 02 Cell+Selection+and+Reselction
1/37
Cell Selection/Reselection
Network optimization SSMC Training Center1
Cell Selection / Cell Reselection
Contents
1 Cell Selection 3
1.1 Measurements for Normal Cell Selection 4
1.2 Criteria for Cell Selection 5
2 Cell Reselection 13
2.1 Necessary Actions for a Cell Reselection 14
2.2 Phase 1 MS 15
2.3 Phase 2 MS 16
2.4 Triggers for Cell Reselection 18
3 Parameters for Cell Selection/Reselection 21
4
Exercise 35
7/29/2019 02 Cell+Selection+and+Reselction
2/37
Cell selection/Reselection
Network optimization SSMC Training Center2
7/29/2019 02 Cell+Selection+and+Reselction
3/37
Cell Selection/Reselection
1 Cell Selection
Network optimization SSMC Training Center3
7/29/2019 02 Cell+Selection+and+Reselction
4/37
Cell selection/Reselection
Cell selection/reselection are processes, which are performed by a GSM mobilestation in idle mode.
The MS uses the cell selection algorithm to look for a cell (of the chosen PLMN)
where it can camp on ("camping on a cell").
If the MS looses coverage of that cell (caused for example by moving out of the cell)it will look for the most suitable alternative cell (of the selected PLMN) and it willcamp on that cell. This is called cell reselection.
The cell selection /reselection processes are described in GSM 03.22, GSM 05.08and ETSI TS 123 122.
1.1 Measurements for Normal Cell Selection
In case of normal cell selection the MS has no prior knowledge on which GSM 900 orDCS 1800 frequencies are BCCH carriers. Therefore the MS has to search in thebeginning all RF carriers of the corresponding system (124 carriers for P-GSM, 174carriers for E-GSM and 374 carriers for DCS 1800), and has to measure the signalstrength on each RF carrier. The MS takes 5 measurement samples per RF carrierwhich are averaged:
AV_RXLEV = 1/5 x (RXLEV1 + RXLEV2 + ... + RXLEV5)
A multi band MS searches all carriers within its band of operation. The number ofcarriers searched corresponds to the sum of carriers on each band of operation.
Network optimization SSMC Training Center4
7/29/2019 02 Cell+Selection+and+Reselction
5/37
Cell Selection/Reselection
1.2 Criteria for Cell Selection
Based on these measurements the MS can estimate whether a cell will be anappropriate serving cell from the radio propagation point of view, i.e. whether therewill be a sufficient link quality:
1.2.1 C1 Criterion for Cell Selection
C1 = AV_RXLEV - RXLEV_ACCESS_MIN - max (0, MS_TXPWR_MAX_CCH - P )
RXLEV_ACCESS_MIN: minimum received level at the MS required for accessto the system
MS_TXPWR_MAX_CCH: maximum allowed MS transmit power on RACH
P: Powerclass of MS specified in GSM O5.05
Power Class (GSM 05.05) Max. Output Power(GSM 900)
Max. Output Power(DCS 1800)
1 -- 1 Watt = 30 dBm
2 8 Watt = 39 dBm 0.25W = 24 dBm
3 5 Watt = 37 dBm 4 Watt = 36 dBm
4 2 Watt = 33 dBm
5 0.8 Watt= 29 dBm
Power classes of GSM 900 and DCS 1800 MS
Network optimization SSMC Training Center5
7/29/2019 02 Cell+Selection+and+Reselction
6/37
Cell selection/Reselection
During cell selection procedure the MS will select only those cells which have C1 > 0.
This means that the averaged received level downlink has to be greater than thethreshold RXLEV_ACCESS_MIN + max (0, MS_TXPWR_MAX_CCH - P):
AV_RXLEV > RXLEV_ACCESS_MIN + max (0, MS_TXPWR_MAX_CCH - P)
The maximum term is included to ensure a sufficient uplink received level even forMS of low maximum transmit power:
If P < MS_TXPWR_MAX_CCH, then the C1 criterion is equivalent to:
AV_RXLEV > RXLEV_ACCESS_MIN + (MS_TXPWR_MAX_CCH - P)
i.e. the averaged received level downlink has to exceed the RXLEV_ACCESS_MINby a certain margin to ensure that the Base Station can receive the MS even in caseof a MS with low maximum output power.
If P > MS_TXPWR_MAX_CCH, then the C1 criterion reduces to:
AV_RXLEV > RXLEV_ACCESS_MIN
Network optimization SSMC Training Center6
7/29/2019 02 Cell+Selection+and+Reselction
7/37
Cell Selection/Reselection
1.2.2 Suitable Cell
Beside the C1 radio criterion there are some other criteria (administrative and trafficcontrol) for a cell to be suitable:
A Suitable Cell is defined as a cell which
is part of the selected PLMN,
is unbarred (parameter CELL_BAR_ACCESS = 0),
has a value C1 > 0,
is not in a location area forbidden for national roaming.
To allow e.g. emergency calls the conditions for a serving cell are less restrictive:An Acceptable Cell is defined as a cell which
is unbarred,
has a parameter C1 > 0.
Network optimization SSMC Training Center7
7/29/2019 02 Cell+Selection+and+Reselction
8/37
Cell selection/Reselection
The general strategy for cell selection is to find the suitable cell with the highest C1(best estimated link quality). If no suitable cell can be found, an acceptable cell isselected.
Network optimization SSMC Training Center8
7/29/2019 02 Cell+Selection+and+Reselction
9/37
Cell Selection/Reselection
no
Cell Selection
Algorithm
(no BCCH Info)
yes
measure allcarriers
sort by receivedlevel
carriers in list
trial carrier:best level in list
BCCH
decode BCCH
suitable cellno
yes
no
yes
Selection of anacceptable cell
try only carriers ofBCCH allocation
remove trialcarrier from list
nocell
in selected
PLMN
Camp on normal
priority cell
yes
Fig. 1 Cell selection for phase 1 MS - no BCCH info is stored
Network optimization SSMC Training Center9
7/29/2019 02 Cell+Selection+and+Reselction
10/37
Cell selection/Reselection
For phase 2 MS there is an additional parameter called CELL_BAR_QUALIFY(values: 0, 1) used to assign different priorities to cells:
CELL_BAR_QUALIFY = 0 normal priority cell
CELL_BAR_QUALIFY = 1 low priority cell
A MS tries first to select a suitable normal priority cell. If no such cell can be found, asuitable low priority cell is selected.
Network optimization SSMC Training Center10
7/29/2019 02 Cell+Selection+and+Reselction
11/37
Cell Selection/Reselection
yes
Cell Selection
Algorithm
(no BCCH Info)
measure all carriers
sort by received level
carriers in list
trial carrier:
best level in list
BCCH
decode BCCH
suitable cell
normal priority
Selection of an
acceptable cell
no
yes
no
no
yes
no
no yes
yes
low priority
cell found
Camp on low
priority cell
suitable low priority
cell found
try only carriers of
BCCH allocation
try only normal priority
cells
remove trial
carrier from list
nocellin selected
PLMN
Camp on normal
priority cell
yes
Fig. 2 Cell selection for phase 2 MS - no BCCH info is stored
Network optimization SSMC Training Center11
7/29/2019 02 Cell+Selection+and+Reselction
12/37
Cell selection/Reselection
1.2.3 Cell Selection with Stored BCCH Information
Optionally, the MS may store information on received level on BCCH carriers whenswitched off.
When switched on, the MS first performs measurements on these carriers. If cellselection for the corresponding cells is not successful, normal cell selection is carriedout.
Network optimization SSMC Training Center12
7/29/2019 02 Cell+Selection+and+Reselction
13/37
Cell Selection/Reselection
2 Cell Reselection
Network optimization SSMC Training Center13
7/29/2019 02 Cell+Selection+and+Reselction
14/37
Cell selection/Reselection
While moving within the radio network in idle mode another cell may be more appro-priate to serve the MS. Therefore cell reselection may be performed.
For the following discussion the MS shall camp on a cell which is called serving cell.
2.1 Necessary Actions for a Cell Reselection
The following actions are performed by the MS to detect whether or not a cellreselection is necessary:
Detection of a Downlink Signaling Failure:
The downlink signaling failure counter DSC is a counter running in the MS. Thestarting value of this counter is called DSC0 and is set by the MS to the followingvalue:
DSC0 = round(90 / BS_PA_MFRMS)
The value of BS_PA_MFRMS is broadcasted in the system informations on theBCCH of the serving cell.
Each BS_PA_MFRMS, the MS attempts to decode the messages on its pagingsub-channel. Depending on whether or not this decoding is successful, the valueof the downlink signaling failure counter DSC is modified in the following way :
successful decoding: DSC new = DSC old + 1
if DSC new + 1 > DSC0 DSC new = DSC old
unsuccessful decoding: DSC new = DSC old - 4
If DSC < 0 the MS has detected a downlink signaling failure.
Network optimization SSMC Training Center14
7/29/2019 02 Cell+Selection+and+Reselction
15/37
Cell Selection/Reselection
Monitoring of all BCCH carriers given in the BCCH allocation (neighbor cells) ofthe serving cell
Taking at least 5 samples of the received level from the serving cell (on pagingsub-channel) as well as from the neighbor cells
=> AV_RXLEV(serving cell) and AV_RXLEV (neighbor cell)
Decoding of full BCCH data of the serving cell at least every 30 sec
Decoding of BCCH data of the 6 strongest neighbor cells at least every 5 minutes
2.2 Phase 1 MS
From the radio propagation point of view it is worth to select a new (neighbor) cell ifthe received level from that neighbor cell exceeds the received level of the currentserving cell. Forphase 1 MS this is expressed using the C1 criterion
C1 (neighbor cell) > C1 (serving cell).
For the reselection process for phase 1 MS the neighbor cells are ordered accordingto their C1-value.
Network optimization SSMC Training Center15
7/29/2019 02 Cell+Selection+and+Reselction
16/37
Cell selection/Reselection
2.3 Phase 2 MS
Forphase 2 MS a modified path loss criterion, the C2 criterion, is usedThe C2 criterion depends on the value of a timer T, which is calledPENALTY_TIMER.
The timer T is started in the MS for each cell in the list of the 6 strongest neighborcells as soon as it is placed on the list.
Timer T is reset to 0 if the cell is removed from the list.
During penalty time:
C2 = C1 + CELL_RESELECT_OFFSET - TEMPORARY_OFFSET
After penalty time:
C2 = C1 + CELL_RESELECT_OFFSET
For penalty time = 31 the whole time:
C2 = C1 - CELL_RESELECT_OFFSET
CELL_RESELECT_OFFSET, TEMPORARY_OFFSET, and PENALTY_TIME are cellreselection parameters which are broadcasted on the BCCH of the cell in the systeminformations if CELL_RESLECT_PARAM_IND (Cell Reselection ParameterIndication) is set to 1.
Network optimization SSMC Training Center16
7/29/2019 02 Cell+Selection+and+Reselction
17/37
Cell Selection/Reselection
Cell included in the
list of 6 strongest
C2
C1
T
CELL_RESELECT_OFFSETTEMPORARY_OFFSET
PENALTY_TIME
Fig. 3 Illustration of the C2 criterion
A negative TEMPORARY_OFFSET reduces the priority of a cell in the list of strong-est neighbor cells.
A positive CELL_RESELECT_OFFSET increases the priority of a cell in the list ofstrongest neighbor cells.
This mechanism may be applied in hierarchical cell structures to keep fast moving
mobiles in the umbrella cells and slow moving mobiles in the micro cells:When a mobile reaches the coverage area of a (neighbor) micro cell given by the C1criterion, this cell becomes effectively excluded from reselection during thePENALTY_TIME.
A fast moving mobile is assumed to have left the coverage area of the micro cell be-fore PENALTY_TIME is reached and hence the micro cell is not selected.
In contrast a slow moving mobile is assumed to be still within the coverage area ofthe micro cell when PENALTY_TIME has expired.
Applying the positive CELL_RESELECT_OFFSET, this cell is selected with prefer-
ence.
Network optimization SSMC Training Center17
7/29/2019 02 Cell+Selection+and+Reselction
18/37
Cell selection/Reselection
2.4 Triggers for Cell Reselection
Cell reselection is triggered by the following conditions:1. C1 < 0 for the serving cell for a period of 5 s
2. MS detects a downlink signaling failure
3. Serving cell becomes barred
4. Phase 1 MS
C1 (serving cell) < C1 (suitable neighbor cell) if the suitable neighbor cell is in thesame location area
C1 (serving cell) + CELL_RESELECT_HYSTERESIS < C1 (suitable neighbor
cell) if the suitable neighbor cell is in another location area for a period of 5 sec.5. Phase 2 MS
C2 (serving cell) < C2 (suitable neighbor cell) if the suitable neighbor cell is in thesame location area
C2 (serving cell) + CELL_RESELECT_HYSTERESIS < C2 (suitable neighborcell) if the suitable neighbor cell is in another location area for a period of 5 sec.
6. A random access attempt is unsuccessful even after the maximum number ofrepetitions.
For phase 2 there is the additional trigger:
7. A location update request has been rejected with cause location area not al-lowed.
Network optimization SSMC Training Center18
7/29/2019 02 Cell+Selection+and+Reselction
19/37
Cell Selection/Reselection
(l)(h)
Radius of Cell 2
for selection
(l) low power MS
(h) high power MS
(a) (b)
Cell Reselection
(a) no change of location area
(b) change of location area
C1=0
C1
BTS1 BTS2
CELL_RESELECT_
HYSTERESIS
direction of movementPhase 1 MS
high power class MS
low power class MS
BTS1 BTS2
Fig. 4 Illustration of cell selection / reselection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center19
7/29/2019 02 Cell+Selection+and+Reselction
20/37
Cell selection/Reselection
Network optimization SSMC Training Center20
7/29/2019 02 Cell+Selection+and+Reselction
21/37
Cell Selection/Reselection
3 Parameters for Cell Selection/Reselection
Network optimization SSMC Training Center21
7/29/2019 02 Cell+Selection+and+Reselction
22/37
Cell selection/Reselection
BA (BCCH) - BCCH Allocation broadcasted on BCCH
In each cell the absolute radio frequency carrier number BCCH_ARFCN_NC(n) of
each of its neighbor cell n has to be known. This information is broadcasted as theso-called BCCH Allocation to all MS in the respective cell. On the correspondingfrequencies the MS take measurement samples of the received level used for cellselection / reselection.
Furthermore, the BCCH of neighbor cells has to be decoded by the MS (at leastevery 5 min) to know the current values of the control parameters for the reselectionalgorithm.
Object DB Name Range Step Size Unit
ADJC BCCHFREQ
(Taken fromTGTCELL)
0...1023 1 -
BCCH_ARFCN_NC(n)
Network optimization SSMC Training Center22
7/29/2019 02 Cell+Selection+and+Reselction
23/37
Cell Selection/Reselection
CELL_BAR_ACCESS - Cell Barred for AccessCELL_BAR_ACCESS - Cell Barred for Access
A mobile station cannot camp on a barred cell, i.e. a barred cell is not selected by the
cell selection/reselection procedure.
A mobile station cannot camp on a barred cell, i.e. a barred cell is not selected by the
cell selection/reselection procedure.Mobile stations which camp on a cell while it becomes barred initialize the reselectionprocedure to find a new (unbarred) cell, i.e. traffic load is distributed to neighbor cells.Mobile stations which camp on a cell while it becomes barred initialize the reselectionprocedure to find a new (unbarred) cell, i.e. traffic load is distributed to neighbor cells.
This means that e.g. neither a call nor a location update can start in a barred cell.This means that e.g. neither a call nor a location update can start in a barred cell.
However, a cell barred for access is not barred for incoming handovers. To barr a cellcompletely, e.g. for maintenance reasons also incoming handovers have to beavoided.
However, a cell barred for access is not barred for incoming handovers. To barr a cellcompletely, e.g. for maintenance reasons also incoming handovers have to beavoided.
To reduce overload in a certain cell more moderately without distributing the overloadto neighbor cells, barring of access classes has to be used. Barring access for an
access class does not trigger a cell reselection for MSs of that class.
To reduce overload in a certain cell more moderately without distributing the overloadto neighbor cells, barring of access classes has to be used. Barring access for an
access class does not trigger a cell reselection for MSs of that class.
Object DB Name Range Step Size Unit
BTS CELLBARR FALSE/TRUE - -
CELL_BAR_ACCESS - Cell Barred for Access
default: FALSE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center23
7/29/2019 02 Cell+Selection+and+Reselction
24/37
Cell selection/Reselection
RXLEV_ACCESS_MIN - Minimum Downlink Received Level for Cell to beselected
The parameter RXLEV_ACCESS_MIN determines the cell border for a MS in idlemode by means of the C1 or C2 criterion respectively.
Choosing a high value reduces the risk of a handover immediately after call setup.
On the other hand the value has to be low enough to achieve a sufficient overlap be-tween adjacent cells (especially if they belong to different location areas).
It has to be observed that the overlap may be different for mobiles of different powerclasses (refer to MS_TXPWR_MAX_CCH).
In any case RXLEV_ACCESS_MIN has to be above the MS receiver sensitivity level(-100 dBm for DCS1800, -102 dBm for GSM handhelds, -104 dBm for other GSM
MS).Furthermore, it has to harmonize with the handover thresholds (RXLEV_MIN,L_RXLEV_HO).
Object DB Name Range Step Size Unit
BTS RXLEVAMI 0...63 1 RXLEV
RXLEV_ACCESS_MIN - Minimum downlink received level for cell to be selected
default: 6
RXLEV 0 = less than -110 dBm.
RXLEV 1 = -110 dBm to -109 dBm.
...
RXLEV 62 = -49 dBm to-48 dBm.
RXLEV 63 = greater than -48 dBm.
Network optimization SSMC Training Center24
7/29/2019 02 Cell+Selection+and+Reselction
25/37
Cell Selection/Reselection
MS_TXPWR_MAX_CCH - Maximum allowed MS Transmit Power on RACH
The transmit power level the MS uses for the access on the Random Access Chan-
nel is given by the minimum of two values: the maximum possible transmit power of the MS (given by the power class P of the
MS)
the maximum allowed power for access within the respective cell
(given by MS_TXP WR_MAX_CCH).
This parameter affects the
the random access procedure
the cell selection procedure.
Random access:
If there is a collision of channel requests on the random access channel, the one withthe higher received level has a good chance to be decoded and to get a response bythe BTS.
Hence MS with higher output power are preferred. This imbalance can be avoided bychoosing a low maximum allowed transmit power.
Cell Selection:
To be selected by the cell selection procedure, a cell has to fulfill the C1 criterion
C1 > 0 where
C1 = AV_RXLEV - RXLEV_ACCESS_MIN - Max(0, MS_TXPWR_MAX_CCH - P )
Choosing for example MS_TXPWR_MAX_CCH = Pmin where Pmin is the outputpower level for the minimum power class 5 (29 dBm), the C1 criterion reduces to
AV_RXLEV > RXLEV_ACCESS_MIN
for MSs of all power classes. Hence the same idle mode cell border is seen by eachmobile.
Network optimization SSMC Training Center25
7/29/2019 02 Cell+Selection+and+Reselction
26/37
Cell selection/Reselection
Choosing for example MS_TXPWR_MAX_CCH = Pmax where Pmax is the outputpower level for the maximum power class 1 (43 dBm), the C1 criterion reduces to
AV_RXLEV > RXLEV_ACCESS_MIN + ( MS_TXPWR_MAX_CCH - P )
for MSs of all power classes. Hence, a larger cell radius is seen by a mobile of higheroutput power than by a mobile of lower output power. On the other hand one canensure by this mechanism that a certain uplink received level is exceeded by eachMS independent of its power class.
Object DB Name Range Step Size Unit
BTS MSTXPMAXCH 0...31 1 2 dB
MS_TXPWR_MAX_CCH - Maximum allowed MS transmit power on RACH
default: 2
For the values of MS_TXPWR_MAX_CCH see the power control level defined inGSM rec. 05.05:
MS GSM900 Phase 1 MS GSM900 Phase 2 MS DCS1800
0 := 43 dBm 0 := 39 dBm 0 := 30 dBm
1 := 41 dBm 1 := 39 dBm 1 := 28 dBm
2 := 39 dBm 2 := 39 dBm 2 := 26 dBm
3 := 37 dBm 3 := 37 dBm 3 := 24 dBm
... ... ...
15 := 13dBm 19 := 5 dBm 15 := 0 dBm
16-31 := 13 dBm 20-31 := 5 dBm 16-31 := 0 dBm
Network optimization SSMC Training Center26
7/29/2019 02 Cell+Selection+and+Reselction
27/37
Cell Selection/Reselection
POWER_OFFSET - Additional Parameter for Class 3 DCS1800 MSPOWER_OFFSET - Additional Parameter for Class 3 DCS1800 MS
The parameter POWER_OFFSET is only used by class 3 DCS1800 MS to calculate
the C1-criterion described as follows.
The parameter POWER_OFFSET is only used by class 3 DCS1800 MS to calculate
the C1-criterion described as follows.C1 = AV_RXLEV - RXLEV_ACCESS_MIN - Max(0,MS_TXPWR_MAX_CCH +POWER_OFFSET- P).C1 = AV_RXLEV - RXLEV_ACCESS_MIN - Max(0,MS_TXPWR_MAX_CCH +POWER_OFFSET- P).
Object DB Name Range Step Size Unit
BTS PWROFS 0...3 1 2 dB
Power_Offset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center27
7/29/2019 02 Cell+Selection+and+Reselction
28/37
Cell selection/Reselection
CELL_RESELECT_HYSTERESIS - Hysteresis for Reselection of a Cell fromanother Location Area
In idle mode the MS selects a new (neighbor) cell if the received level of the neighborcell exceeds the received level of the current cell in order to be served by the cell withthe expected best link quality. However, due to fading effects, the propagationconditions may change rapidly and therefore a reselection may occur very frequently.
If the cells involved in the reselection process belong to the same location area, fre-quent cell reselection does not have an effect on the network performance.
But if the involved cells belong to different location area, the reselection of a new celltriggers a location update procedure, which causes signaling load (e.g. on theSDCCH) and involves all network elements.
To avoid unnecessary signaling load by forward and backward reselection due tofading, a hysteresis given by the parameter CELL_RESELECT_HYSTERESIS isintroduced, i.e. a cell from another location area is selected only if the correspondingreceived level exceeds the level of the current serving cell by the value of thisparameter. This is expressed in terms of the C1 (phase 1) or C2 (phase 2) criterion:
C1 (serving cell) + CELL_RESELECT_HYSTERESES(serving) < C1 (suitableneighbor cell)
or
C2 (serving cell) + CELL_RESELECT_HYSTERESES(serving) < C2 (suitableneighbor cell)
respectively.
The adjustment of CELL_RESELECT_HYSTERESES should be a compromise be-tween
reduction of unnecessary location updates (high value) and
selection of the cell with best reception quality (low value).
Object DB Name Range Step Size Unit
BTS CELLRESH 0...7 1 2 dB
CELL_RESELECT_HYSTERESIS - Hysteresis for reselection of a cell from anotherlocation area
default: 2
Network optimization SSMC Training Center28
7/29/2019 02 Cell+Selection+and+Reselction
29/37
Cell Selection/Reselection
CELL_RESELCT_PARAM_IND_ - Phase 2 Reselection Parameter IndicationCELL_RESELCT_PARAM_IND_ - Phase 2 Reselection Parameter Indication
CELL_RESELECT_PARAM_IND=1:CELL_RESELECT_PARAM_IND=1:
The cell reselection parameters CELL_RESELECT_OFFSET,TEMPORARY_OFFSET and PENALTY_TIME used for the C2 criterion as well asthe parameter CELL_BAR_QUALIFY are broadcasted on the BCCH. Theseparameters are taken into account by phase 2 MS, but are ignored by phase 1 MS.
The cell reselection parameters CELL_RESELECT_OFFSET,TEMPORARY_OFFSET and PENALTY_TIME used for the C2 criterion as well asthe parameter CELL_BAR_QUALIFY are broadcasted on the BCCH. Theseparameters are taken into account by phase 2 MS, but are ignored by phase 1 MS.
CELL_RESELECT_PARAM_IND = 0:CELL_RESELECT_PARAM_IND = 0:
The cell reselection parameters and CELL_BAR_QUALIFY are not broadcasted onthe BCCH.The cell reselection parameters and CELL_BAR_QUALIFY are not broadcasted onthe BCCH.
A phase 2 MS then uses the value 0 for all these parameters, i.e. C1 = C2.A phase 2 MS then uses the value 0 for all these parameters, i.e. C1 = C2.
Object DB Name Range Step Size Unit
BTS CRESPARI 0...1 - -
CELL_RESELCT_PARAM_IND_ - Phase 2 Reselection Parameter Indication
default: 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center29
7/29/2019 02 Cell+Selection+and+Reselction
30/37
Cell selection/Reselection
CELL_BAR_QUALIFY
Parameter is used to assign a priority to a cell selection process.
A suitable cell of low priority is only selected if no suitable cell of normal priority canbe found.
This parameter can be used e.g. in hierarchical cell structures that the MS initiallyselects an umbrella cell.
Object DB Name Range Step Size Unit
BTS CBQ 0...1 1 -
CELL_BAR_QUALIFY
default: 0
normal priority: 0
low priority: 1
Network optimization SSMC Training Center30
7/29/2019 02 Cell+Selection+and+Reselction
31/37
Cell Selection/Reselection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center31
PENALTY_TIME - Time to Apply a Negative Offset to C2 of a Neighbor Cell
PENALTY_TIME < 31:
A timer T is started in the MS for each cell in the list of the 6 strongest neighbor cellsas soon as it is placed on the list.
T is reset to 0 if the cell is removed from the list. During Penalty Time
(T < PENALTY_TIME) a negative TEMPORARY_OFFSET is applied to the C2 of therespective neighbor cell
C2 = C1 + CELL_RESELECT_OFFSET - TEMPORARY_OFFSET
which is removed after Penalty Time (T > PENALTY_TIME):
C2 = C1 + CELL_RESELECT_OFFSET.
PENALTY_TIME = 31:
C2 = C1 - CELL_RESELECT_OFFSET.
For PENALTY_TIME = 31 the priority of a neighbor cell for reselection is permanentlyreduced.
Object DB Name Range Step Size Unit
BTS PENTIME 0...30 and 31:special meaning
1 20 sec
PENALTY_TIME - Time to apply a negative offset to C2 of a neighbor cell
default: 5
7/29/2019 02 Cell+Selection+and+Reselction
32/37
Cell selection/Reselection
TEMPORARY_OFFSET
Subtracting TEMPORARY_OFFSET from CELL_RESELECT_OFFSET reduces the
priority of a cell in the list of strongest neighbor cells, i.e. during run time of the timerthe corresponding neighbor cell is effectively barred for cell reselection.
Object DB Name Range Step Size Unit
BTS TEMPOFF 0...7 1 10 dB
7: infinity
TEMPORARY_OFFSET
default: 1
Network optimization SSMC Training Center32
7/29/2019 02 Cell+Selection+and+Reselction
33/37
Cell Selection/Reselection
CELL_RESELECT_OFFSET
Adding CELL_RESELECT_OFFSET increases the priority of a cell in the list of
strongest neighbor cells when the timer has expired.This mechanism may be applied in hierarchical cell structures to keep fast movingmobiles in the umbrella cells and slow moving mobiles in the micro cells: When amobile reaches the coverage area of a (neighbor) micro cell, given by the C1criterion, this cell becomes effectively excluded from reselection during thePENALTY_TIME.
A fast moving mobile is assumed to have left the coverage area of the micro cell be-fore PENALTY_TIME is reached and hence the micro cell is not selected. In contrast,a slow moving mobile is assumed to be still within the coverage area of the micro cellwhen PENALTY_TIME has expired. Applying the positive
CELL_RESELECT_OFFSET, this cell is selected with preference.
Object DB Name Range Step Size Unit
BTS CRESOFF 0...63 1 2 dB
CELL_RESELECT_OFFSET
default: 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network optimization SSMC Training Center33
7/29/2019 02 Cell+Selection+and+Reselction
34/37
Cell selection/Reselection
Network optimization SSMC Training Center34
7/29/2019 02 Cell+Selection+and+Reselction
35/37
Cell Selection/Reselection
4 Exercise
Network optimization SSMC Training Center35
7/29/2019 02 Cell+Selection+and+Reselction
36/37
Cell selection/Reselection
Network optimization SSMC Training Center36
7/29/2019 02 Cell+Selection+and+Reselction
37/37
Cell Selection/Reselection
Exercise 1
Fill in the relevant parameters for Cell Selection/Reselection:
Specification Name(GSM Name)
BSC-Database Name Value Range Remarks