R
BABY WALKERInstruction Manual
Conforms to standard ASTM F977-12
Read all instructions before assembly and use of the walker.
WARNING!
Recommended for children whocan support their body with legs.
Max Weight:26 lbs.
Max Height: < 32 in.
2 3
AssemblyParts List
Item Name Quantity Picture
A Walker Subassembly 1 pc
B Seat Pad 1 pc
C Seat Back Support 1 pc
D Activity Tray 1 pc
E Grip Pads 6 pcs
F Mirror (Left & Right) 1 pc (each)
G Rear Spoiler 1 pc
H Race Car Wheels (Front & Back) 2 pcs (each)
I Front Walker Wheels 2 pcs
J Back Walker Wheels 2 pcs
1. Unpack all contents and please check that all parts are present before starting assembly. Please see PARTS LIST(pg 2).
2. To open the baby walker, raise the Walker Subassembly to the middle position as shown in Figure 1.
3. Assemble the four Race Car Wheels as shown in Figure 2. (Large wheels in back / Smaller wheels in front)
4. Assemble the Rear Spoiler as shown in Figure 3.
5. Assemble the Mirror (Left & Right) as shown in Figure 4.
6. Assemble the Seat Back Support as shown in Figure 5.
Figure 3 Figure 4 Figure 5
Figure 1 Figure 2
4 5
11. Turn base up side down, insert the grip pads properly with middle post and the both side post as Figure 11. Be sure all 6 Grip Pads are attached to the base securely before use. 12. The baby walker can be used for 3 different heights. To adjust heights, remove baby from walker. Turn the safety button lengthwise and press the safety button until the mechanism is released. Adjust to desired height as shown in Figure 12.13. When the position has been selected, check that the safety button turned through 90 degrees to prevent the accidental release of the mechanism as shown in Figure 13. ALWAYS FOLLOW THIS PROCEDURE. NEVER USE THE BABY WALKER IF THE BUTTON IS NOT IN THE SIDEWAYS POSITION. IMPORTANT: Never change the height when the baby is in the walker.14. To compact the walker, turn upside down and turn safety button lengthwise and push down to lowest level.15. Toy tray requires 2 “AA” batteries (not included). Please use Philips head screwdriver to unfasten battery cover. Insert battery as Figure 14. Secure battery cover back. Caution: Old and new batteries (alkaline standard or rechargeable) should not be mixed in use. Remove battery before storing the toy tray.
Figure 11 Figure 12
Figure 13 Figure 14
7. Push crotch portion of seat pad inside out to form seat, so the fabric is on inside of pad.
8. Insert the 8 round tabs on the seat pad into slots located around the seat ring, slide tabs through holes. Turn tray up side down. Pull tabs and align into grooves. You may have to push tabs from top of walker to properly fasten. Ensure that all 8 tabs have clicked over the grooves.
9. Test: Push down hard on seating area of seat pad to make sure seat is securely in place. CAUTION: Do not use walker if all tabs are not secured properly, otherwise child may fall through walker.
10. Place walker on a solid flat surface with bottom of base facing upward. Insert the pins of the wheels into their housing, pressing them until they snap into position. Please check that wheels are locked into place as Figure 9 and Figure 10.
Figure 7
Figure 6 Figure 9 Figure 10
Assembly Assembly
Figure 6
90˚
6 7
WARNING! WARNING!
• Use only on flat surfaces free of objects that could cause this walker to tip over.• Never use near hills, roadways, or pools.• Prevent access to stairs, steps and uneven surfaces; • Guard all fires, heating and cooking appliances;• To avoid burns, keep child away from hot liquids, stoves, radiators, space heaters, electrical cords and other potential hazards from reach;• Prevent collisions with glass in door, windows and furniture;• Do not use the baby walking frame if any components are broke or missing;• This baby walking frame should be used only for short periods of time (e.g. 20 minutes);• This baby walking frame is intended to be used by children who can sit unaided, approximately from 6 months. It is not intended for children weighing more than 26 lbs or 32 inches tall• Do not use replacement parts other than those approved by the manufacturer or distributor.
• Never carry this walker with child in it. Never adjust seat while child is in product.• DO NOT lift or carry by tray, toy tray, or toys.• DO NOT use this walker until baby can sit up unassisted.• To reduce the chance of child slipping out of seat, check that both feet of child touch the ground.• Discontinue using this walker when your child can stand unaided or walk unassisted.• To maintain stopping performance, clean grip pads regularly with damp cloth.
Only use this walker if your child MEETS ALL of the requirements below:• Can support body weight with legs,• Weight is unaided up to 26 lbs,• Height is less than 32 inches.
DEATH or SERIOUS INJURY can occur DEATH or SERIOUS INJURY can occur
WARNING!
Never leave child unattended.
Avoid serious injury or death.Block stairs/steps securely before using walker
Always keep child in view while in walker. WARNING:WARNING - STAIR HAZARD:
8
Keep this instruction manual for future use.
KidsEmbrace, LLC
www.KIDSEmbrace.comQuestions or comments?
Email: [email protected]
6711 Odessa AveVan Nuys, CA 91406
12805.2
Call: 1-866-947-3287
![HAND-CARVED INDIAN ROUND DRESSER MIRROR - ASSEMBLY …€¦ · PARTS ENCLOSED: 1 NO. ITEM DESCRIPTION QTY 2 Pcs. 2 Pcs. 7 Pcs. 2 Pcs. 2 Pcs. 1 Pc. 2 3 4 5 6 A [1] CARVED ROUND MIRROR](https://static.documents.pub/doc/80x56/60036b3ee1edd66cc651997f/hand-carved-indian-round-dresser-mirror-assembly-parts-enclosed-1-no-item-description.jpg)
