STOP! ¡PARADA!
STOP! ¡PARADA!
16615-LPI
Call Us First! DO NOT RETURN TO STORE.
For immediate help with assembly or product information call our toll-free number:
1-888-827-9056 or email:
[email protected] Our staff is ready to provide assistance.
April through October M - F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
ANTES DE DEVOLVERLO, ¡LLÁMENOS! Si desea más información sobre el montaje, llámenos sin coste
adicional alguno al siguiente teléfono: +1-888-827-9056
o correo electrónico: [email protected]
Nuestro personal le proporcionará toda la ayuda que necesite. Abril por octubre M - F 8:00 ESTA a 7:00 P.M. EST
el sábado 8:30 ESTA a 4:30 P.M. EST noviembre por marzo M - F 8:00 ESTA a 5:00 P.M. EST
We manufacture kits from select construction grade lumber and engineered wood products. Construction grade lumber, a product cut from trees, has many natural characteristics and blemishes that may be present in some of the pieces you receive in your kit. Natural characteristics and blemishes in construction lumber may include knots, torn wood grain along edges, minor cracks/splits, twists, limited bark along edges and pitch pockets that may exude sap. Be assured that the individual parts have been cut and inspected to remove as many of the wood’s natural, less appealing characteristics as possible. These characteristics and/or blemishes will not affect the strength, durability, or structural integrity of the fi nished product. Generally, the exterior trim parts selected for your kit are graded from only one side and should be installed with the most attractive side outward. Our limited warranty does not cover the natural characteristics and blemishes that occur with construction grade lumber products.
Fabricamos nuestros equipos de madera elaborada y de productos maquinados de madera. La madera elaborada, producto de árboles, tiene muchas características e imperfecciones naturales que puedan tener algunas piezas contenidas en el equipo. Estas imperfecciones y características pueden incluir nudos, grano rasgado sobre el borde, rajas/grietas pequeñas, torsiones, cortezas en el borde, y bolsos que exuden savia. Asegurams que hemos cortado e inspeccionado las partes individuales para eliminar las características naturales menos atractivas posibles. Estas características y/o imperfecciones no afectarán la fuerza, durabilidad ni la integridad estructural del producto fi nal. Po lo general, las piezas de moldura exterior seleccionadas para su equipo se elaboran de un solo lado y deben ser instaladas con la parte más atractiva por fuera. Nuestra garantía limitada no cubre las características e impefecciones que ocurren con los productos de madera elaborada.
TOOLS REQUIRED
HERRAMIENTAS NECESARIAS
Customer ServiceServicio al cliente1-888-827-90561000 Ternes DriveMonroe, MI 48162
Incluye instrucciones del edifi cio 366 x 305 cm.
Includes 12' x 10' Building Instructions.
01/22/201416615-LPI
12' x 10' GableAguilón 366 x 305 cm
Paint Tools Level
Phillips Screwdriver Hammer
Escalera
Lápiz
Cinta métrica Escuadra
Desmarador cruz
Martillo
Herramientas para pintar Nivel
Electric drill with #2 Phillips Tip Nail Pouch Chalk Line
Taladro eléctrico Broca “Phillips” Bolsillo para clavos
Cordeau
Utility Knife
Caulk Gun
Clamps
Wood Glue
Navaja
Pistolo para masillado
Grapas
Pegamento para madera
Pencil
Tape Measure Square
Ladder
Building / Edifi cios12' x 10'
(366 x 305 cm)
2
First...Check with your local building authority
before erecting.Read instructions thoroughly before
you begin.
Building CodesOur buildings are designed to meet most local
and national U.S. codes and are not meant to be used for living space.
General construction drawings can be provided.
Check All PartsIf a part is missing, circle the part in
question and call.Please note the primer color may vary on
siding and trim parts. This is a factory applied primer intended for preparing your building for painting. This is NOT a finish coat. This primer color variation will not affect the look of your building once painted.
ImportantLumber is graded from one side, use
most attractive face to the outside.In a drawing, a dotted line represents a
part hidden from view (like a part under a panel).
Assistance requiredAssistance is necessary to handle, fit,
and secure some components.
Squareness is very Important!Keep 90° corners and 90°
perpendiculars throughout the assembly to ensure all components fit together.
Check
Safety!
foundation sizeBef
Check for protruding nails, pound anyprotruding nails into the wood or cutthem off flush.
ore starting on your foundation, make sure you are building the correct size foundation for your building.
Always wear OSHA-APPROVEDsafety glasses throughoutassembly process.
- - BEFORE YOU BEGIN
- ANTES DE EMPEZAR -
Primero...Consulte la autoridad de construcción
local antes de construir el edificio.Lea las instrucciones completamente
antes de empezar.
Códigos de ConstrucciónHemos diseñado nuestros edificios a que
conformen con todos los códigos de construcción locales y nacionales. Los edificios no están proyectados como residencia.
Se disponen planes generales de construcción.
Compruebe todas las piezasSi falta una pieza, indícala con un círculo
y llámenos. Aviso: El color del imprimador puede
variar en la covertura y las partes de la moldura. Este imprimador se aplica en la fábrica y es para preparar su edificio para pintar. NO es una capa de pintura terminada. La variación en el color del imprimador no afectará la apariencia de su edificio al pintarlo.
ImportanteLa Madera está elaborada en un solo
lado. Use el lado más atractivo en el exterior.
Si falta una pieza, póngale un círculo y llámenos.
En un dibujo una línea punteada representa una pieza no vista (por ejemplo, una pieza debajo de un panel).
Ayuda requeridoSeleccione un sitio nivelado.Será necesario pedir ayuda para
manejar, unir, y reforzar algunas piezas.
¡Es preciso escuadrar el edificio!Mantenga ángulos de 90° en las
esquinas y los perpendiculars durante la construcción para asegurar que todas las piezas se unen correctamente.
Comprueba las dimensiones de lacimentación.
Compruebe que las dimensiones de la cimentación son las correctas para el edificio.
¡Seguridad! Inspeccione para clavos sobresalientes;
hinque cualquier clavo sobresaliente en la madera o córtelo nivelados con la madera.
Siempre lleve gafas de seguridadaprobadas por OSHA durante laconstrucción.
3
WOOD SIZE CONVERSION CHART
1” x 4”.................3/4” x 3-1/2” (1,9 x 8,9 cm)
2” x 4”..............1-1/2” x 3-1/2” (3,8 x 8,9 cm)
2” x 3”..............1-1/2” x 2-1/2” (3,8 x 6,3 cm)
1” x 3”.................3/4” x 2-1/2” (3,8 x 6,3 cm)
CUADRO DE CONVERSIÓN DE TAMAÑO DE LA MADERA
Nominal Board Size
Actual Size
Tamaño nominalde la tabla
Tamaño real
NOTE NOTA
RS
RS
RS
Dos letras o tres letras de identi� cación están marca-das horizontalmente en las piezas. Letras de identi� -cación de una sola letra no están en las piezas.
Double and Triple Letter Part identi� cation letters are stamped on part and read horizontally, single letter part letters not stampedon parts.
4
366 x 305 cmLISTA DE PIEZAS
12' x 10'PARTS LIST
WA
LL
S
48 x 84”(122 x 213 cm)
48 x 84”(122 x 213 cm)
A x1C
PA
RE
DE
S
x7 x2B
x1E
x1D
STL
SG
SPx3
x1
x2
2 x 4 x 44-1/2” (5 x 10 x 113 cm)
2 x 4 x 34” (5 x 10 x 86,4 cm)
2 x 4 x 48” (5 x 10 x 122 cm)
23-7/8 x 84”(60,6 x 213 cm)
AL
G
AF
G-2
G-1
x5
x2 x2
x2
x4
2 x 4 x 7” (5 x 10 x 18 cm)
23-7/8 x 28-1/2” (61 x 73 cm)
2 x 4 x 18-1/8” (5 x 10 x 40 cm)
AI
x2
2 x 4 x 78-1/2” (5 x 10 x 199 cm)
AM x2
RP
RL
x2
x42 x 4 x 20-1/2”
(5 x 10 x 52 cm)
2 x 4 x 24” (5 x 10 x 61 cm)
BG
AO
PYA
AV
AJ
x1
x4
x1
48 x 84”(122 x 213 cm)
48 x 84”(122 x 213 cm)
TP ULx6 x5
2 x 4 x 96” (5 x 10 x 244 cm)
2 x 4 x60-1/2” (5 x 10 x 154 cm)
2 x 4 x 12-1/2” (5 x 10 x 32 cm)
2 x 4 x 11-5/8” (5 x 10 x 29,5 cm)
2 x 4 x 22-1/2” (5 x 10 x 57 cm)
2 x 4 x 19-3/4” (5 x 10 x 50,2 cm)
2 x 4 x 92-1/2” (5 x 10 x 235 cm)
UM
x222 x 4 x 68”
(5 x 10 x 173 cm)2 x 4 x 67”
(5 x 10 x 170 cm)
23-9/16 x 48” (60 x 122 cm)
23-9/16 x 48” (60 x 122 cm)
F
7/16 x 3 x 66”(1,1 x 7,6 x 168 cm)
x1
x1
x1x1 GAA
Gauge Block(bloque de medida)
3/4" (19 mm)
GAUGE BLOCK FOR 3/4" (19 mm) MEASUREMENT.
5
J L Mx2
366 x 305 cmLISTA DE PIEZAS
TE
CH
O12' x 10'
PARTS LISTR
OO
FT
RIM
MO
LDU
RA
7/16 x 48 x 96”(1,1 x 122 x 244 cm)
Rafter GussetViga Placade Unión
AD x12x14 UK x2 x2 x2
7/16 x 47-7/8 x 48”(1,1 x 121,6 x 122 cm)
6 x 24” (15 x 61 cm)
2 x 4 x 65-1/2”(5 x 10 x 166 cm)
x2
5/8 x 4 x 72-1/4” (1,6 x 10 x 183,5 cm)
5/8 x 4 x 72-1/4” (1,6 x 10 x 183,5 cm)
AJL AJR x2 TM x1
2 x 4 x 72” (5 x 10 x 183 cm)
1 x 3 x 72” (2,5 x 7,6 x 183 cm)
HJ x1x2 x2VXAS
2 x 6 x 96” (5 x 15 x 244 cm)
2 x 6 x 49-1/2” (5 x 15 x 126 cm)
7/16 x 23-1 /8 x 96”(1,1x 59 x 244 cm)
7/16 x 23-1/8 x 48”(1,1 x 59 x 122 cm)
ES
TA
NT
ES
DE
SV
ÁN
SH
EL
VE
SL
OF
T
L-1
B-1
S-1
L-2
B-2
S-2
P-2P-1
2 x 4 x 24” (5 x 10 x 61 cm)
1 x 4 x 24” (2,5 x 7,6 x 61 cm)
1 x 4 x 20-1/2” (2,5 x 7,6 x 52 cm)
1 x 3 x 23-7/8” (2,5 x 7,6 x 61 cm)
2 x 3 x 10” (5 x 7,6 x 25 cm)
2 x 3 x 23-7/8” (5 x 7,6 x 60,6 cm)
3/8 x 14-1/4 x 22-1/4”(36 x 56,5 cm)
2 x 4 x 96” (5 x 10 x 244 cm)
1 x 4 x 96” (2,5 x 10 x 244 cm)
1 x 3 x 96” (2,5 x 7,6 x 244 cm)
2 x 3 x 96” (5 x 7,6 x 244 cm)
2 x 3 x 19” (5 x 7,6 x 48 cm)
RL
JS
BABC AC
PT
LR
LW
B-3
x4
x1
x1x2 x6
x1
x1x1
7/16 x 36 x 96”(1,1x 91,4 x 244 cm)
7/16 x 19-1/2 x 92-1/2”(1,1x 49,5 x 235 cm)
7/16 x 11-1/2 x 96”(1,1x 30 x 244 cm)
7/16 x 15-7/8 x 36”(1,1 x 40 x 91,4 cm)
7/16 x 19-1/2 x 23-7/8”(1,1 x 49,5 x 60,6 cm)
23-7/8 x 23-7/8”(61 x 61 cm)
23-7/8 x 96”(61 x 244 cm)
7/16 x 11-1/2 x 23-7/8”(1,1 x 30 x 40 cm)
TP
KP BE
x4
x2 x2x1
x1
x1
x1
x5
x1
x1
x1
x6
6
PU
ER
TA
DO
OR
LeftDoor
Puertaizquierda
RightDoor
Puertaderecha
V W Y
FE
RR
ET
ER
ÍAH
AR
DW
AR
E
x23/4” (19 mm) x6
3/4” (19 mm) x11
366 x 305 cmLISTA DE PIEZAS
12' x 10'PARTS LIST
x1 x1
x2
Vent Abertura
1/2” (13 mm) x12 x2
2 x 3 x 68-1/4”(5 x 7,6 x 173 cm)
1 x 3 x 26-5/8”(2,5 x 7,6 x 68 cm)
OO
AH
AHR x1
x1AHL
1 x 3 x 62” (2,5 x 7,6 x 157,5 cm)
1 x 3 x 62” (2,5 x 7,6 x 157,5 cm)
x1
64” MetalThreshold
Entrada de Metal 162,5 cm
Hinge(Bisagra)
x4
x390
x1270
x28
x150
x100
x11
x95
x95
x123/4” (19 mm)
Zx1
1-1/2” (38 mm) x2
1-1/2” (3,8 cm)
1-1/4” (3,2 cm)
3/4” (1,9 cm)
2” (5,1 cm)
2” (5,1 cm)
2” (5,1 cm)
3” (7,6 cm)
3” (7,6 cm)
Window Ventana
x1
TR
IMM
OLD
UR
A 5/8 x 3 x 21” (1,6 x 7,6 x 53 cm)
BWR x1
5/8 x 3 x 8-1/2” (1,6 x 7,6 x 21,6 cm)
DF x4
5/8 x 3 x 28-1/8” (1,6 x 7,6 x 71,4 cm)
DT x2BWL
5/8 x 3 x 21” (1,6 x 7,6 x 53 cm)
x1
30” x 22-1/2” (76 x 57 cm)
x2
5/8 x 3 x 30-1/8”(1,6 x 7,6 x 76,5 cm)
AZ x6
x4
3/8 x 1-3/4 x 83-1/2” (1 x 4,4 x 212,1 cm)
3/8 x 1-3/4 x 81-1/2” (1 x 4,4 x 207 cm)
x4
7
HELPFUL MATERIAL NOTICE
FOR THE BEST LOOKING FINISHED PRODUCT WE RECOMMEND THAT YOU INSPECT, SORT AND LAY OUT MATERI-ALS PRIOR TO BEGINNING ASSEMBLY OF YOUR BUILDING.
IMPORTANT!Bui lding Tip
¡ IMPORTANTE!! !Consejo
• Install wall framing with any blemished sides toward the siding and facing rear of building. (Fig. B)
Always install the material leaving the best edge and best sur-face visible.
Please remember that these blemishes in no way negatively af-fect the strength or integrity of our product.
La madera es un producto natural que tiene defectos inherentes. Todo la estructura interior ha sido aprobada por ofrecer una re-sistencia estructural y no por su aspecto. La guarnición exterior ha sido aprobada por tener un buen lado según las normas de la industria.
Instale siempre el material dejando visibles el mejor borde y la mejor super� cie.
Recuerde que estos defectos no afectan de forma negativa la resistencia o la integridad de nuestros productos.
B C
A
CON EL FIN DE OBTENER EL PRODUCTO ACABADO DE MEJOR ASPECTO RECO-MENDAMOS QUE INSPECCIONE, CLASIFIQUE Y ORGANICE LOS MATERIALES ANTES DE EMPEZAR A MONTAR SU EDIFICIO.
Wood is a natural product that has inherent blemishes. All interi-or framing is graded for structural strength and not appearance. Exterior trim is graded for one good side per industry standards.
• Install corner trim, gable trim and fascia with any blemished sides toward the siding material. (Fig. C)
AVISO ÚTIL SOBRE LOS MATERIALES
• Blemishes can be easily installed to provide the best appearance. (Fig. A)
• La parte con defectos puede instalarse fácilmente de modo que el edi� cio tenga el mejor aspecto. (Fig. A)
• Instale la guarnición de las esquinas, la guarnición de los hastiales y las impostas con los lados con defectos apuntando hacia el material lateral. (Fig. C)
• Instale el entramado de la pared con los lados con defectos apuntando hacia los costados y haciendo frente a la parte trasera del edi� cio. (Fig. B)
Please feel free to call our Consumer Help Line - Toll Free1-888-827-9056
April through October M - F 8:00 AM to 7:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
Llame de forma gratuita a nuestra línea de ayuda alconsumidor
1-888-827-9056Abril por octubre M - F 8:00 ESTA a 7:00 P.M. EST
el sábado 8:30 ESTA a 4:30 P.M. ESTnoviembre por marzo M - F 8:00 ESTA a 5:00 P.M. EST
8
Racking a Roof
Position panel � ush with outside front edge of rafter and nail in two corners as shown. Rack panel square by moving opposite end up or down until panel is � ush along peak of rafters and secure with one nail in each corner. Ensure spacing of center rafters and nail as instructed.
Posicione los paneles nivelados con el borde delantero exterior de la viga y clave en las dos esquinas como en el dibujo. Alinee escuadra el panel por mover los extremos opuestos arriba o abajo hasta que el panel esté nivelado a lo largo del punto más alto de las vigas, y fíjelo con un clavo en cada es-quina. Compruebe el espacio de las vigas centrales y clave como indicado.
Alineando un techo
Flush with Rafter Peak.Nivelado con la parte másalta de las vigas.
FlushAl ras
Rack for Squareness.Nivele para escuadrar.
NailClavo
YOU MAY NEED TO RACK YOUR WALL PANELS AND ROOF PANELS TO ENSURE SQUARENESS BEFORE COMPLETELY NAILING.
IMPORTANT!Bui lding Tip
¡ IMPORTANTE!Consejo
ES PRECISO ALINEAR LOS PANELES DE LOS MUR-OS Y DEL TECHO ANTES DE CLAVARLOS COMPLE-TAMENTE PARA ASEGURAR LA ESCUADRA.
When building walls, always apply panel at far left � rst. Position panel � ush with top of wall frame and nail in upper corners as shown. Rack wall square by moving lower end of wall panel right or left until panel is � ush with framing along left edge and secure with one nail in each lower corner. Continue nailing as instructed.
Racking a Wall Alineando un Muro
Al construir los muros, siempre � je primero el panel hasta la izquierda extrema. Posicione el panel nivelado con la parte superior de la es-tructura del muro y clávelo en la esquina superior como en el dibujo. Alinee nivelado el muro por mover el lado inferior a la derecha o a la izquierda hasta que el panel esté nivelado con la estructura a lo largo del borde izquierda. Fije con un clavo en cada esquina inferior.
A
B
NailClavo
NailClavo
FlushAl ras
Top Corner Should Be Flush.
La esquina superior debe estar nivelado con la estructura.
THIS PAGE SHOWS EXAMPLES:This may not be how your shed walls are built.
Refer to pages showing wall assembly.
ESTA PÁGINA DEMUESTRA EJEMPLOS: Éste puede no ser cómo se construyen las paredes. Re� eraa las páginas reales que demuestran el montaje de la pared.
FlushAl ras
9
SITE PREPARATION• Site must be properly leveled.
• Site should have natural drainage and no standing water.
A
B C
4"(10 cm)
3-1/2"(8.9 cm)
Fasten treated 2x4” sill plates to slab using approved concrete anchors. (Treated sill plates and fasteners not included.)
Treated SillSoleras Inferiors Tratadas
Building Size
A B
144”(366 cm)
Dimensiones del edi� cio
C
137”(348 cm)
PREPARACIÓN DEL SITIO• El sitio debe de estar nivelado correctamente.
• Instale una barrera contra yerbajos debajo de la estructura.
Fije las soleras inferiores tratadas 5x10 cm a la losa con anclajes de concreto aprobados. (Las soleras y los anclajes no están incluidos.)
120”(305 cm)
12’ x 10’(366 x 305 cm)
Concrete Slab Foundation Base en losa de concreto
DOOR SIDE
LADO DE LAPUERTA
NOTE:Treated sill-plates are not included in your kit.
NOTA:Las travesaño-placas tratadas no se incluyen con su kit.
FOUNDATION OPTIONS (Mater ia l Not Suppl ied With Ki t )
IF YOU ASSEMBLE YOUR BUILDING ON A CONCRETE SLAB FOLLOW THESE SPECS.
OPCIONES PARA LA CIMIENTO(No inc lu idas )
SI USTED CONSTRUYE ESTE EDIFICIO EN UNA FUNDACIÓNDEL CEMIENTO SIGA ESTAS ESPECIFICACIONES.
10
WALL ORIENTATION ORIENTACIÓN DE LAS PAREDES
• The � oor may be used as a stable work surface.• El piso se puede utilizar como super� cie de trabajo estable.
Wall frame facing upward.Revestimiento del marco de la pared hacia arriba.
NOTE: Supports not included in kit. NOTA: Vigas de ayuda no incluidas en kit.
• Organize your assembly procedure during the build process to avoid over-handling of the walls.• Organice su procedimiento de la asamblea durante e procesode la estructura para evitar la sobre-dirección de las paredes.
NOTE: Your kit’s walls may be different from wall shown. NOTA: Las paredes de su kit pueden ser diferentes de la pared demostrada.
11
x 56
3” (7,6 cm)
120”305 cm
96”244 cm
96”244 cm
72”183 cm
48”122 cm
24”61 cm
24”61 cm
24”61 cm
78-1/2”199 cm
AI x6
RL
TP
TPRL
SIDE WALL PARED LATERAL
BUILD TWO IDENTICAL WALLS AS SHOWNHAGA DOS PAREDES IDÉNTICAS COMO SE MUESTRA
12
SIDE WALL PARED TRASERAx 272
2” (5 cm)
Imp
ort
ant
Dim
ensi
on
D
imen
sió
n im
po
rtan
te
B
AA
48”
122
cm48
”12
2 cm
24”
61 c
m
1-1/
2”3,
8 cm
1-1/
2”3,
8 cm
6”15
cm
6”15
cm
12”
30 c
m
HIN
T:
Use
� o
or
as a
wo
rk s
urf
ace!
CO
NS
EJO
:¡U
tilic
e el
pis
o c
om
o s
up
er�
cie
de
trab
ajo
!Flu
shA
l ras
Flu
shA
l ras
See
Pag
e 7
for
Bu
ildin
g T
ip!!
!¡V
er la
pág
ina
7 pa
ra u
n co
nsej
o!!!
T
OP
/ T
AP
A
BO
TT
OM
/ P
AR
TE
INF
ER
IOR
Flu
shA
l ras
13
x 18
3” (7,6 cm)FRONT WALL PARED DELANTERA
Begin the front wall assembly procedure by pre-assembling the door header.
Comience el procedimiento del montaje de la pared delantera premontando el cabezal de puerta.
1
2
3Turn assembled header over and nail using eight 3” nails as shown.Dé vuelta a excesivo cabezal montada y concluya la enclavación usando ocho clavos de los 7.6cm como se muestra.
Assemble header with ten 3” nails as shown. Ensure alignment of parts at the sides.Monte cabezal con diez clavos de los 7,6 cm como se muestra. Asegure la alineación de piezas en los lados.
GluePegamento
FlushAl ras
3” (7,6 cm)x8
3” (7,6 cm)x10
Ensure parts AM and F are aligned perfectly on a � at surface. Center F with 1/2" gap at each side. Spread glue across AM and F as shown.Asegúrese que las partes AM y F estén alineadas perfectamente en una super� cie plana. Centre F con el boquete de 13 mm en cada lado. Separe el pegamento a través AM y F como se muestra.
AM
AM
F
1/2”13 mm
1/2”13 mm
TOP VIEW / VISIÓN SUPERIOR
1/2”13 mm
1/4”6 mm
1/4”6 mm
AM F
14
x 30
3” (7,6 cm)
DIMENSIONS ARE TO CENTER OF STUDS.LAS DIMENSIONALES ESTÁN AL CENTRO DEL MONTANTES.
MAINTAIN DIMENSION BETWEEN STUDS.
MANTENGA LAS DIMENSIONESENTRE LOS MONTANTES.
UL
AO
AO
AV
AI x5
STL
HINT:Use � oor as a work surface!
CONSEJO:¡Utilice el piso como super� cie
de trabajo!
AJ
FRONT WALL PARED DELANTERA
137”348 cm
92-1/2”235 cm
58-1/4”148 cm
44-1/2”113 cm
36-3/8”92 cm
60-1/2”154 cm
12-3/8”31 cm
12-1/2”
32 cm
69-1/4”176 cm
78-1/2”199 cm
38”96,5 cm
1-1/2”3,8 cm
1-1/2”3,8 cm
67”170 cm
64”162,5 cm
12-3/8”31,4 cm
126-3/4”322 cm
FlushAl ras
CENTER OF STUDCENTRO DEL MONTANTE
15
x 40
3” (7,6 cm)
DIMENSIONS ARE TO CENTER OF STUDS. LAS DIMENSIONALES ESTÁN AL CENTRO DEL MONTANTES.
I M P O RTA N T !¡ I M P O RTA N T E ! MAINTAIN DIMENSION
MANTENGA LAS DIMENSIONES
HINT:Use � oor as a work surface!
CONSEJO:¡Utilice el piso como super� cie
de trabajo!
FRONT WALL PARED DELANTERA
67”170 cm
68-1/2”174 cm
7”17,8 cm
44-1/2”113 cm
20-1/2”52 cm
34”86,4 cm
78-1/2”199 cm
11-5/8”
29,5 cm
SG
BG
AI
AL x5
HeaderCabezal
FlushAl ras
Install end part AL � rst, allowing for more room to swing the hammer.
Instale la pieza AL del extremo primero. El martillo necesitará el espacio de funcionamiento adicional.
16
x 14
3” (7,6 cm)
64” 162,5 cm
68” 173 cm I M P O RTA N T !
¡ I M P O RTA N T E !
MAINTAIN DIMENSION MANTENGA LAS DIMENSIONES
UM
HINT:Use � oor as a work surface!
CONSEJO:¡Utilice el piso como super� cie
de trabajo!
FRONT WALL PARED DELANTERA
17
3/4” 1,9 cm
6” 15 cm
3/4” 1,9 cm
3/4” 1,9 cm
1-1/2” 3,8 cm
6” 15 cm
64” 162,5 cm
I M P O R TA N T !¡ I M P O R TA N T E !
MAINTAIN DIMENSION MANTENGA LAS DIMENSIONES
x 50
2” (5 cm)
Align left side of panel with the 3/4” mark. Alinee el izquierda del panel con la marca de 1,9 cm.
HINT: oor as a work surface!
CONSEJO: cie
de trabajo!
ARETNALED DERAPLLAW TNORF
Install with painted side facing up.Instale el lado con la pintura para arriba.
ImportantDimension
Dimensiónimportante
D
¡Ver la página 8 para un consejo!See Page 8 for Building Tip!
18
3/4” 1,9 cm
1-1/2” 3,8 cm
12” 30 cm
6” 15 cm
6” 15 cm
64” 162,5 cm
I M P O R TA N T !¡ I M P O R TA N T E !
MAINTAIN DIMENSION MANTENGA LAS DIMENSIONES
x 62
2” (5 cm)
E
HINT: oor as a work surface!
CONSEJO: cie
de trabajo!
FlushAl ras
ARETNALED DERAPLLAW TNORF
FlushAl ras
Important DimensionDimensión importante
Install with painted side facing up.Instale el lado con la pintura para arriba.
¡Ver la página 8 para un consejo!See Page 8 for Building Tip!
19
ARETNALED DERAPLLAW TNORFx 35
2” (5 cm)
64” 162,5 cm
I M P O R TA N T !¡ I M P O R TA N T E !
MAINTAIN DIMENSION MANTENGA LAS DIMENSIONES
1-1/2” 3,8 cm
6” 15 cm
Hint: Use part “TP” (2 x 4 x 96") as a temporary support until wall is installed. Consejo: Utilice la parte “TP” (5 x 10 x 244 cm) como a la ayuda temporal hasta la pared está instalada.
3" Nail - Do not sink completely.Clavo de los 7,6 cm - no se hunda totalmente.
FlushAl ras
ImportantDimension
Dimensiónimportante
F
3” (7,6 cm) x2
¡Ver la página 8 para un consejo!See Page 8 for Building Tip!
20
x 24
3” (7,6 cm)
116-1/2”296 cm
137”348 cm
92-1/2”235 cm
68-1/2”174 cm
44-1/2”113 cm
92-1/2”235 cm
44-1/2”113 cm
92-1/2”235 cm
20-1/2”52 cm
78-1/2”199 cm
AI x5STLUL
UL
STL
BACK WALL PARED TRASERA
¡Ver la página 8 para un consejo!See Page 8 for Building Tip!
BOTTOMPARTE INFERIOR
TOP / TAPA
HINT:Use � oor as a work surface!
CONSEJO:¡Utilice el piso como super� cie de
trabajo!
21
x 120
2” (5 cm)
HIN
T:U
se �
oor a
s a
wor
k su
rfac
e!
CO
NSE
JO:
¡Util
ice
el p
iso
com
o su
per�
cie
de
trab
ajo!1-
1/2”
3,8
cm
6”15
cm
6”15
cm
12”
30 c
m
AA
A1-
1/2”
3,8
cm
Flu
shA
l ras
Im
po
rtan
t D
imen
sio
n
Dim
ensi
ón
imp
ort
ante
48”
122
cm48
”12
2 cm
48”
122
cm
TO
P /
TA
PA
BO
TT
OM
/ P
AR
TE
INF
ER
IOR
BACK WALL PARED TRASERAS
ee P
age
7 fo
r B
uild
ing
Tip
!!!
¡Ver
la p
ágin
a 7
para
un
cons
ejo!
!!
INS
TA
LL
TH
IS P
AN
EL
FIR
ST
INS
TA
LE
EL
ES
TE
PA
NE
L P
RIM
ER
3/4”
19 m
m3/
4”19
mm
Flu
shA
l ras
22
x 12
3” (7,6 cm)
3”7,6 cm
FRONTFRENTE
6”15 cm
x 27
2” (5 cm)
Level wall and brace.Nivele el pared y refuerzala.Do not sink nails completely.
No hinque los clavoscompletamente.
Temporary (TP)No permenente (TP)
3” NailsClavos 7,6 cm
3” NailClavo 7,6 cm
FlushAl ras
FRONTFRENTE
2” NailsClavos 5 cm
LEFT WALL
LEFT WALL
PARED IZQUIERDA
PARED IZQUIERDA
Center wall assembly on � oor.Centre la asamblea de la pared sobre el piso.
120”305 cm
1-1/2” Overhang Proyección 3,8 cm
23
6”15 cm
x 12
3” (7,6 cm)
x 27
2” (5 cm)
3”7,6 cm
Center wall assembly on � oor. Centre la asamblea de la pared sobre el piso.
Level wall and brace.Nivele el pared y refuerzala.
Do not sink nails completely.No hinque los clavoscompletamente.
TemporaryNo permenente
3” NailClavo 7,6 cm
FlushAl ras
2” NailsClavos 5 cm
RIGHT WALL
RIGHT WALL
PARED DERECHA
PARED DERECHA
FRONTFRENTE
FRONTFRENTE
1-1/2” Overhang Proyección 3,8 cm
24
6”15 cm
6”15 cm
Flush / Al ras
BACK WALL PARED TRASERA
BACK WALL PARED TRASERA
3” (7,6 cm)
x 16
3” (7,6 cm)
x 55
2” (5 cm)
Remove temporary supports after wall is installed.
Quite las ayudas temporales después de que la pared esté instalada.
1-1/2” Overhang Proyección 3,8 cm
25
x 14
3” (7,6 cm)
6”15 cm
6”15 cm
3” (7,6 cm)
3” (10 cm)
2” NailsClavos 5 cm
x 46
2” (5 cm)
FRONT WALL
FRONT WALL
PARED DELANTERA
PARED DELANTERA
Remove temporary support (TP) after wall is installed.
Quite la ayuda temporal (TP) después de que la pared esté instalada.
26
10' x 12' 305 x 366 cm
DOBLADORES DE LA PARED
(16) 3” Screws4 SCREWS PER
CORNER.
(16) 7,6 cm Tornilllos4 tornillos por
esquina
TP
UL
SP TP
SP
RP
RP UL
96”244 cm
96”244 cm
48”122 cm
48”122 cm
20-1/2”52 cm
Nail 24” TYP.Clavo 61 cm
TÍPICOS
20-1/2”52 cm
92-1/2”235 cm
92-1/2”235 cm
DOORPUERTA
Ensure all doubler seams are non-aligned over seams of wall top plates.Asegúrese que todos los empalmes del doblador sean no alineados
sobre empalmes de las placas de la tapa de la pared.
WALL DOUBLERS DOBLADORES DE LA PARED
3” (7,6 cm) x 60
3” (7,6 cm) x 16
27
ROOF TRUSS VIGA
x2
x5
IMPORTANT! Build two rafters with 1 gusset.
¡IMPORTANTE!Haga dos viga con 1 escudete.
IMPORTANT! Build � ve rafters with 2 gussets.
¡IMPORTANTE!Haga cinco vigas con 2 escudetes.
Use � oor, wall and part QL as a � xture to help build the rafters.
Utilice el piso, la pared y la parte QL como un accesorio paraayudar a construir los vigas.
Do not sink nails completly.No golpee totalmente en clavos.
CONSEJO:¡Utilice el piso y las paredes
para ayudar a montarlos vigas!
HINT:Use � oor and walls to help
assemble rafters!
QL
120”305 cm
3” (7,5 cm)
120”305 cm
65-1/2”166 cm
65-1/2”166 cm
120”305 cm
65-1/2”166 cm
65-1/2”166 cm
28
ROOF TRUSS VIGA2” (5 cm)
x 144
Build � ve rafters with 2 gussets. Haga cinco vigas con 2 escudetes.
Build two rafters with 1 gusset. Haga dos viga con 1 escudete.
120”305 cm
FlushAl ras
CenterCentro
FlushAl ras
1/4”6 mm
FlushAl ras
U x2AD AD
GluePegamento
Remove QL after all trusses are assembled. Quite QL después de que todos los vigas estén montados.
2”(5 cm)
120”305 cm
GluePegamento
FlushAl ras
CenterCentro
FlushAl ras
1/4”6 mm
U
AD AD2” (5 cm)
FlushAl ras
BUILD ONLY TWO.HAGA SOLAMENTE DOS.
BUILD ONLY FIVE.HAGA SOLAMENTE CINCO.
x2
x5
29
ROOF TRUSS VIGAx 28
END VIEW / VISTA DEL EXTREMO
24-3/8”62 cm
24-3/8”62 cm
24”61 cm
24”61 cm
24”61 cm
24”61 cm
DIMENSIONS ARE TO CENTER OF RAFTERS.LAS DIMENSIONALES ESTÁN AL CENTRO DEL VIGAS.
DIMENSIONS ARE FROM OUTSIDE OF WALL PANELS.LAS DIMENSIONES SON FUERA DE LOS PANELES DE PARED.
TRUSS ENDS ARE INSTALLED FLUSH WITH INSIDE OF WALL PANELSLOS EXTREMOS DE VIGA ESTÁN INSTALADOS A RAS DENTRO
DE LOS PANELES DE PARED
3” (7,6 cm)
Trusses are � ush with front and back wall panels.Los vigas son rasantes con el frente y los paneles de pared traseros.
FlushAl ras
FlushAl ras IMPORTANT!
¡IMPORTANTE!
30
WALL PARED1-1/2” (3,8 cm)
x 24
6”15 cm
2-1/2”6,4 cm
2-1/2”6,4 cm
2-1/2”6,4 cm
1-3/4”4,5 cm
3-1/2”8,9 cm
6”15 cm
1
2
AF
G-1
G
G-2
FlushAl ras
x2
This space has been left blank intentionally.
Este espacio vacío es intencional.
31
WALL
WALL
PARED
PARED
2” (5 cm)
2” (5 cm)
6”15 cm
6”15 cm
6”15 cm
6”15 cm
Center gable panel assembly on back wall. Montaje del panel de centro del aguilón en la pared trasera.
Center gable panel assembly on right wall. Montaje del panel de centro del aguilón en la pared derecha.
2” NailsClavos 5 cm
2” NailsClavos 5 cm
3” Screws Tornillos 7,6 cm
3” (7,6 cm)
3” (7,6 cm)
x4
x4
x 45
x 45
LEFT WALLPARED IZQUIERDA
RIGHT WALLPARED DERECHA
FlushAl ras
FlushAl ras
FlushAl ras
FlushAl ras
3” Screws Tornillos 7,6 cm
32
LOFT DESVÁNx 48
3” (7,6 cm)
2 Assemble joist with 3” nails in a staggered pattern. Monte la vigueta con clavos 7,6 cm en un patrón escalonado.
GluePegamento
RL
TP
TP
RL
x2
FlushAl ras
FlushAl ras
FlushAl ras
1Ensure parts TP and RL are aligned perfectly on a fl at surface. Spread glue across RL and TP as shown.Asegúrese que las piezas TP y RL estén alineadas perfectamente en una superfi cie plana. Distribuya el pegamento a través de RL y del TP como se muestra.
3” (7,6 cm)x12
2 x 4 x 96”5 x 10 x 244 cm
2 x 4 x 24”5 x 10 x 61 cm
3 Turn assembled joist over and repeat staggered nail pattern. Dé la vuelta a la vigueta montada y repita el patrón escalonado del clavo.
33
LOFT DESVÁNx 14
x 12
3” (7,6 cm)
3” (7,6 cm)
LEFT WALLPARED IZQUIERDA
FlushAl ras
FlushAl ras
3” NailsClavos 7,6 cm
3” ScrewsTornillos 7,6 cm
3” ScrewsTornillos 7,6 cm
4
LEVELNIVEL
LW2 x 3 x 23-7/8”5 x 7,6 x 60,6 cm PT 2 x 3 x 96”
5 x 7,6 x 244 cm
PYA
5
LOFT DESVÁN
WINDOWVENTANA
LOFT JOIST
LOFT JOIST
VIGUETA DEL DESVÁN
VIGUETA DEL DESVÁN
3” ScrewsTornillos 7,6 cm
AO
AO
3-1/2”9 cm
3-1/2”9 cm
2 x 4 x 22-1/2”5 x 10 x 57 cm
2 x 4 x 22-1/2”5 x 10 x 57 cm
LEVELNIVEL
LEVELNIVEL
Flush at wall panel. AO es rasante con el panel de pared.
3-1/2”9 cm
3” (7,6 cm) x 8
2 x 4 x 19-3/4” (5 x 10 x 50,2 cm)
34
BENCH BANCO2” (5 cm)
x 20
1
FlushAl ras
x5
B-3
LR
2-1/2”6,35 cm Assemble 5 bench brackets as shown.
Monte 5 soportes del banco como se muestra.
19”48 cm Flush
Al rasFlushAl ras
BENCH BANCO
2
4-7/16”11,3 cm
WINDOW OPENINGABERTURA
DE LA VENTANA
LEVELNIVEL
LR2 x 3 x 19”5 x 7,6 x 48 cm
7/16”11 mm
11-5/8”29,5 cm
3” (7,6 cm)
x2
FlushAl ras
Nail into studs. Clavo en montantes.
35
BENCH BANCO2” (5 cm)
x 21
4
FlushAl ras
B-1 B-2
FlushAl ras
19-1/2 x 92-1/2”49,5 x 235 cm
92-1/2”235 cm
24”61 cm
19-1/2 x 24”49,6 x 61 cm
BENCH BANCO2” (5 cm)
x 15
3
SAME DIMENSIONLA MISMA DIMENSIÓN
FLOOR / PISO
LEVELNIVEL
LR
Reference this height. Re� érase a esta altura.
FlushAl ras
Install � ve bench brackets level with installed bench support (LR) 4-7/16” below window.Instale cinco soportes del banco llano con la ayuda instalada del banco (LR4-7/16” abajo la ventana.
Corner StudMontante
de la esquina
36
BENCH BANCO2” (5 cm)
x 21
P-1 P-2
When installing pegboard, ensure bottom edge of pegboard is in contact with top of bench.
Al instalar pegboard, asegúrese que el borde inferior del pegboard está en contacto con la tapa del banco.
6
FlushAl ras
FlushAl ras
BENCH BANCO2” (5 cm)
3” (7,6 cm)
3” ScrewTornillo 7,6 cm
x 12
x1
5
KP 1 x 4 x 96”2,5 x 10 x 244 cmBA 1 x 4 x 20-1/2”
2,5 x 10 x 52 cm
37
SHELF ESTANTE
2
Flush with top of pegboard.El marco del estante es rasante con la tapa del pegboard.
3” (7,6 cm)
x 12
Assemble shelf frame on a � at surface. Monte el marco del estante en una super� cie plana.
SHELF ESTANTE2” (5 cm)
x 14
1
BC
BE
24”61 cm
48”122 cm
96”244 cm
120”305 cm
72”183 cm
1 x 3 x 24”2,5 x 7,6 x 61 cm
1 x 3 x 96”2,5 x 7,6 x 244 cm
AC x62 x 3 x 10”
5 x 7,6 x 25,4 cm
FlushAl ras
FlushAl ras
38
4
3” ScrewTornillo 7,6 cm
SHELF ESTANTE3” (7,6 cm)
x1
x 26
KP 1 x 4 x 96”2,5 x 10 x 244 cm
BC1 x 3 x 23-7/8”2,5 x 7,6 x 61 cm BE1 x 3 x 96”
2,5 x 7,6 x 244 cm
JS 1 x 4 x 23-7/8”2,5 x 10 x 60,6 cm
FlushAl ras
2” (5 cm)
Keep shelf level.Nivele el estante.
SHELF ESTANTE
3
S-2S-1 11-1/2 x 96”
30 x 244 cm
11-1/2 x 23-7/8”30 x 40 cm
Maintain 24” between supports.Mantenga los 61cm entre las ayudas.
1-1/4” (32 mm)
x 14
24”61 cm
39
LOFT DESVÁN
FlushAl ras
2” (5 cm)
x 45
L-1 L-2
1
8”20 cm
There will be a gap of approximately 1/2” on either side on either side of installed deck panels.Habrá un boquete de aproximadamente 13 mm en cada lado de los paneles del desván después de instalar.
8”20 cm
• Install deck panels centered over loft joists and ledger board. • Instale los paneles del desván centrados sobre las viguetas del desván y tablero de la ayuda del desván.
36”91,5 cm
15-7/8”40 cm
96”244 cm
SHELF ESTANTE
Repeat step 5 on back wall.Repita el paso 5 en la pared trasera.
5
14-5/8”37 cm
62”157,5 cm
CONSEJO:Marque la localización de la ayuda
de estante en fuera del panel.
HINT:Mark shelf support location
on outside of panel.
x6
1-1/4” (32 mm)
Bottom edge of wall panel. Borde inferior del panel de pared.
40
ROOF TECHO2” (5 cm)
x 56
2” (5 cm)
x 39ROOF TECHO
2” (5 cm)
x 112
1
2
K
J
FlushAl ras
Center roof panel edges over rafters. Centre los bordes de los techo paneles sobre el vigas.
See Page 7 for Building Tip!¡Vea la página 7 para el consejo de la construcción!
See Page 7 for Building Tip!¡Vea la página 7 para el consejo de laconstrucción!
L
M
Install lower roof panels (L and M). Instale los paneles más bajos de la azotea (L y M).
Roof Panel / Panel del techo
Panel / Panel
Truss / Viga
Roof Panel / Panel del techo
Panel / Panel
Truss / Viga
• Maintain truss dimension. • Mantenga las dimensiones del armazón.
L23-7/8 x 96”
60,6 x 244 cm
M23-1/8 x 48”
58,7 x 122 cm
All roof panels are attached with 2” nails spaced 6” at panel edges, 12” at panel centers. Todos los paneles de la azotea se atan con los clavos 5 cm espaciaron 15 cm en los bordes del panel, 30 cm en los centros del panel.
K47-7/8 x 48”
121,6 x 122 cm
J48 x 96”
122 x 244 cm
6”15 cm
12”30 cm
41
ROOF TECHO
GLUEPEGAMENTO
GLUEPEGAMENTO
LEVELNIVEL
FlushAl ras
FlushAl ras
TM
TRIMx 48
2” (5 cm)
FlushAl ras
FlushAl ras
AJL
MOLDURA
AJR
x 6
3” (7,6 cm)
End-wall rafterViga de la � n-pared
Third rafter Tercer viga
Trim parts should be � ush with top of roof panels and � ush at corners. Repeat installation at both gables.
Las piezas del moldeado deben ser rasantes con la tapa de los paneles de la azotea y también a ras en las esquinas. Repita la instalación de moldear en ambos aguilones.
FlushAl ras
7/16”11 mm
Roof Panel El panel de techo
42
TRIM MOLDURA1-1/4” (32 mm) x 60
3” (7,6 cm) x 8
Flu
shA
l ras1-
1/4”
3,2
cm
AS
AS
VX
VX
96”
244
cm
49-1
/2”
123
cm
3”7,
6 cm
3”7,
6 cm
3”7,
6 cm
1-1/
4”3,
2 cm
3”7,
6 cm
Flu
shA
l ras
1-1/
4”3,
2 cm
43
TRIM MOLDURA
x483-1/2" (212 cm) x4
81-1/2" (207 cm)
S-1S
S
Flush under side eave trim.Rasante debajo del
moldura del lado del alero.
Seam is � ush. Caulk seam before painting trim. La costura es rasante. Masilla esta costura antes de pintar el moldura.
Flush under gable panel. Rasante debajo del panel del aguilón.
x 48
2” (5 cm)
1-1/4” (32 mm) x 2
PARTE SUPERIOR TOP
x 83” (7,6 cm)
PUERTADOOR
3/8”(0,9 cm)
3/8”(0,9 cm)
OO
GAA
WV
Temporary support Apoyo no permanente
Flush at bottom of both doors.A ras de la parte inferior de ambas puertas.
Do not sink screws completely.No instale los tornillos totalmente.
3/8”(0,9 cm)
3/8”(0,9 cm)
1-1/4” ScrewsTornillos 3,2 cmx8
44
PUERTA
PUERTA
DOOR
DOOR
3” (7,6 cm)
3” (7,6 cm)
x3
x8
• Install hinge boards � ush with edge of panel. • Instale los tableros de la bisagra a ras con la parte inferior del panel.
3” (7,6 cm)
x8
Remove after doors are installed.Ensure doors open properly.
Quite después de que se aten las puertas. Asegure las puertas abiertas correctamente.
2
3
Screw into thewall support.
Atornille en la ayuda de la
pared.
Mark center of door opening.Marque el centro de la abertura
de la puerta.
1CenterCentro
OO
3” ScrewsTornillos 7,6 cm
Temporary support Apoyo no permanente
45
2” (5 cm)DOOR
3/4” (19 mm) x12
x 10PUERTA
x2
3/8’’(0,9 cm)
1’’(2,5 cm)
1-7/8" (4,7 cm)
Inside of Door
Interior de laPuerta
Drill 3/8" HoleTaladro Hoyo (0,9 cm)
2" (5 cm)
FlushAl ras
Drill 3/8" HoleTaladro Hoyo (0,9 cm)
2" Screws5 cm Tornillos
Bottom of door.Parte inferior de la puerta.
Install on left door.Instale en puerta izquierda.
RIGHT DOORPUERTA A LA DERECHA
LEFT DOORPUERTA IZQUIERDA
OUTSIDE OF SHEDFUERA DEL EDIFICIO
OOOO
OO
46
TRIM MOLDURAx 223/4” (1,9 cm)
x 72” (5 cm)
FlushAl ras
LEVELNIVEL
FlushAl ras
AHAH
AHR
AHL
3/4”1,9 cm
CENTERCENTREZ
2”5 cm
HJ
1
2
3
47
Z x4
FlushAl ras
Install hinges (Z) centered on horizontal trim and � ush against piano hinge.
Instale las bisagras (Z) centradas en ajuste horizontal de la puerta. El borde cuadrado
de la bisagra está en contacto con labisagra del piano.
x 12
3/4” (19 mm)DOOR PUERTA
48
MANIJA DE PUERTADOOR HANDLE
1/2"13 mm
1-1/2" (3,8 cm)
35-3/4"90 cmSIDE VIEW
VISTA LATERAL
We suggest pre-drilling with 1/4" drill. Keep drilled hole square to trim to avoid breaking edge of 2x3".
Sugerimos el pretaladrar con taladro de 6mm. Perfore el cuadrado del agujero en el ajuste para evitar romper el borde de la 5x7,6 cm.
INSTALL ON RIGHT DOOR.INSTALE EN PUERTA
A LA DERECHA.
1-1/2"3,8 cm
TOP VIEWVISTA SUPERIOR
1/4" Pre-drill and 1/2" Drill-through.Pretaladre el agujero 6 mmTaladro a través 13 mm.
1
SET SCREWTORNILLO DE PRESIÓN
1-1/2" (38 mm) x2
2
49
DOOR PUERTA
THRESHOLD UMBRALx 11
x 40
Y
3/4” (19 mm)
3/4” (19 mm)
3/4” (19 mm)
1” ScrewsTornillos 25 mmx 40
Reinforce door from the inside with 1” screws through inside door panel into outer trim.
Conduzca los tornillos 25 mm a través del panel interior de la puerta y en el moldeado externo de la puerta.
50
ASAMBLEADE POSTIGOx 18
1” (25 mm)SHUTTERASSEMBLY
DF x4
AZ x6
Install with painted side facing down.Instale el lado con la pintura abajo.
BWR
BWL
Install with painted side facing down.Instale el lado con la pintura abajo.
LEFTIZQUIERDA
RIGHTDERECHA
FlushAl ras
FlushAl ras
30-1/8”77 cm
2-1/2”6,3 cm
2-1/2”6,3 cm
2-1/2”6,3 cm
2-1/2”6,3 cm
2-1/2”6,3 cm
1/2”13 mm
8-1/2”21,6 cm
51
WINDOW
Seal window with high-quality paintable exterior-grade caulk.
Selle la ventana con el exterior-gradode calidad calafatean que puedeser pintado.
VENTANAx 4
WINDOW VENTANAx 20
2” (5 cm)
x 6
3/4” (19 mm)
FlushAl ras
FlushAl ras
FlushAl ras
Install 3/4” screws at “X” from inside.
Instale tornillos 19 mm en el “X”por dentro de.
CENTERCENTREZ
FlushAl ras
CENTERCENTREZ
5-5/8”14 cm
30-1/8”76 cm
5-5/8”14 cm
2-1/2”6,3 cm
2-1/2”6,3 cm
AZ x2
Outside ViewVisión desde el exterior
1-1/4” (3,2 cm)
52
VENT RESPIRADERO1/2” (13 mm)
x6
5”13 cm
6”15 cm
7” - 8”17 cm - 20 cm
14”35,5 cm
To install vent in rear center gable panel cut out gable panel as shown.
Para instalar el respiradero en el panel de centro posterior del aguilón corte el panel del aguilón como se muestra.
VENT RESPIRADERO1/2” (13 mm)
x6
6”15 cm
3” - 5”7,6 cm - 13 cm
14”35,5 cm
• Choose a wall for vent locations.• Cut out wall panel as shown.
• Elija una pared para las localizaciones del respiradero.• Corte los paneles de pared como se muestra.
For optimum cross-ventilation install two vents. Vents should be installed on opposite walls.
Para la cruz-ventilación óptima instale dos respiraderos. Los respiraderos se deben instalar en las paredes opuestas.
For optimum cross-ventilation install two vents. Vents should be installed on opposite walls.
Para la cruz-ventilación óptima instale dos respiraderos. Los respiraderos se deben instalar en las paredes opuestas.
53
Use Acrylic Latex Caulk that is paintable. Caulk at all
horizontal and vertical seams, between the Trim and
Walls, and all around the Door Trim.
Use a high quality exterior acrylic latex paint. When
painting your building, there are a few key areas that
can be easily overlooked that must be painted:
• Bottom edge of all siding and trim
• Inside of doors and all 4 edges
Note: Prime all un-primed exterior wood before painting
DRIP EDGE(Not Included)
DripedgeBorde del gotero
Snip bottom side of drip edge andbend over to other side of roof.
Corte la parte inferior del borde del gotero y dóblela sobre el otro lado del techo.
Side that hangs over side. No Nails.La parte que está colgada sobre un lado.Ningunos clavos.
Close up of drip edge. Vista del .
BORDE DEL GOTERO(No Incluidas)
PAINT AND CAULK(Not Included)
PINTURA Y MASILLADO(No Incluidas)
Building PaintPintura del edi� cio
Trim PaintPintura de moldura
CaulkMasillado
Building SizeDimensiones del edi� cio
Building SizeDimensiones del edi� cio
Use madillado acrílico de latex pintable. Masille todas las costuras horizontals y verticales, entre la moldura y los muros, y alrededor de la moldura de la puerta.
Use pintura acrílica de látex de lata calidad. Al pintar su edi� cio, hay unas áreas claves que hay que pintar:
• Debajo de la moldura en las puertas.
• Debajo de la moldura de esquinas.
• Todo el exterior del edi� cio.
• Las partes interiors y superiors de las puertas y el borde superior de la covertura.
10’ x 12’(305 x 366 cm)
60’18 m
1 Quart/cuartas
2-1/2 Gallons/galones
2 Tubes/Tubos
10’ x 12’(305 x 366 cm)
54
Okay if Shingle Overlaps.
Está bien si la teja so-bresale.
Flush to dripedge
Nivelado al borde del gotero
1"(2.5 cm)
NAILSCLAVOS
Sealing Strip1"
(2.5 cm)1/2"
(1.3 cm)6 Bundles/bultos
Building Size Shingles NeededTejas necesarias
SHINGLES(Not Included)
TEJAS(No Incluidas)
Dimensiones del edi� cio10’ x 12’
(305 x 366 cm)
Clavos
Line up notch on top of Shingle withedge of Roof to stagger the Shingles.
Alinee el corte encima de la teja con el borde del techo para escalonar las tejas.
Flush to edge, stagger each row.Nivele al borde, escalone cada � la.
Maintain same deminsion across. Mantenga la misma dimensión de
un lado al otro.
Remove overhanging shingles.
Quite tejas sobresalientes.
Install � rst row backwards.
Instale la primera � la al revés.
55
Check for protruding nails, pound any protruding nails into the wood or cut them off � ush.
Ridge Cap
NAIL INSPECTION REQUIRED MAINTENANCE
Tapa de cumbrera
Inspeccione para clavos sobresalientes; hinque clavos sobresalientes en la madera or córtelos nivelados con la madera.
Keep grass trimmed and away from building
Corte y quite la hierba cerca del edi� cio.
Keep Sprinklers away from building
Repaint building as needed and in accordance with paint manufacturer requirements
No use rociadores cerca del edi� cio.
5-1/8"(13 cm)
5-7/8"(15 cm)
Pinte el edi� cio de nuevo cada dos años.
INSPECCIÓN DE CLAVOS MANTENIMENTO NECESARIO
SHINGLES(Not Included)
TEJAS(No Incluidas)
Cut Shingles into 3 pieces.
Corte las tejas en tres partes.
Apply pieces to ridge as shown
Fije las piezas a la cumbrera como en el dibujo
56
WARRANTYBackyard Storage Solutions, LLC warrants the following:1. Every product is warranted from defects in workmanship and manufacturing for one year.2. All hardware and metal components are warranted for two years.3. Trim is warranted for 12 years.4. Waferboard siding and sheathing is warranted for two years.5. SmartSide™ siding is warranted for 12 years.6. Timber series buildings’ siding and trim are warranted for 10 years.7. Solar Shed windows are warranted for 1 year.8. Cedar lumber is warranted for 15 years.9. Cedar doors and Cedar Garden Center are warranted for 10 years.10. Metal roof is warranted for 25 years.
Backyard Storage Solutions, LLC will repair, replace or pay for the affected part. In no event shall Backyard Storage Solutions, LLC pay the cost of labor or installation or any other costs related thereto. All warranties are from date of purchase. If a cash refund is paid on an affected part, it will be prorated from the date of purchase.
CONDITIONSThe warranty is effective only when:1. The unit has been erected in accordance with the assembly instructions. 2. The unit has been properly shingled and painted or stained and reasonably and regularly maintained thereafter.3. The failure occurs when the unit is owned by the original purchaser.4. Backyard Storage Solutions, LLC has received the warranty registration card within thirty (30) days of purchase and noti� ca tion of the failure in writing within the warranty period speci� ed above.5. Backyard Storage Solutions, LLC has had reasonable opportunity during the sixty (60) days following receipt of noti� cation to inspect and verify the failure prior to commencement of any repair work.
REQUIREMENTSStorage Buildings & PlayhousesTo validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit; shingle the roof and paint or solid-colored stain the siding using 100% acrylic latex exterior product with a minimum of two (2) coats within sixty (60) days of assem-bly; caulk above all doors and all horizontal and vertical trim boards; paint and seal all exposed edges, sides and faces of SmartSide™ and waferboard siding to include all exterior walls and all sides and all edges of doors.
Gazebos, Pergolas & Timber BuildingsTo validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit. This includes treating all of the exposed cedar and pine surfaces on your gazebo or timber building with an exterior grade wood preservative, an exterior oil-based semi-transparent stain, an acrylic latex exterior paint or an acrylic latex solid color exterior stain within 30 days of assembly and as needed thereafter to maintain your warranty.
Keep vegetation trimmed away from building and make sure siding panels and trim do not come in contact with masonry or cement. The minimum ground clearance for siding must be one half inch (½ inch) from concrete slab or two and one half inches (2 ½”) from the ground when building is erected or constructed on a treated wood � oor kit. Water from sprinklers must be kept off unit. In no event will Backyard Storage Solutions, LLC be responsible for any indirect, incidental, consequential or special damages nor for failure(s) that are caused by events, acts or omissions beyond our control including, but not limited to, misuse or improper assembly, improper maintenance (which eventually leads to rot or decay) and acts of God. Backyard Storage Solutions, LLC will not be held responsible for any labor costs incurred to construct your unit.This warranty gives you certain speci� c rights that vary from state to state.
CLAIM PROCEDURETo make a claim under this warranty, you can either call 1-888-827-9056 or prepare a letter. Please have ready the information below when you call or include the information when writing:1. The model and size of the product.2. A list of the part(s) for which the claim is made.3. Proof of purchase of the Backyard Storage Solutions, LLC item, as shown on the original invoice.4. Run code, as listed on the yellow warranty card enclosed in the product package.
Mail the above information to: Backyard Storage Solutions, LLC Attn: Customer Service 1000 Ternes Monroe, MI 48162
Limited ConditionalWarranty *
*WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.IMPORTANT: This is your warranty certi� cate.Please complete and mail your warranty card to properly validate your warranty. ldr: 03/11/10
57
Backyard Storage Solutions, LLC le garantiza a Ud. que:1. Cada producto no tiene defecto de mano de obra ni de manufactura por un período de un año.2. La ferretería y los componenetes de metal están garantizados por dos años.3. La moldura está garantizada por 12 años.4. La covertura y el entablado están garantizados por dos años.5. La covertura SmartSide™ está garantizada por 12 años.6. La covertura y la moldura de los edi� cios Timber Series están garantizadas por 10 años.7. Las ventanas del Solar Shed están garantizadas por un año.8. La madera de cedro está garantizada por 15 años.9. Las puertas del cedro y el Centro de jardin del Cedro son justi� cados durante 10 años.10. El techo del metal es justi� cado durante 25 años.
Backyard Storage Solutions, LLC reparará, cambiará o pagará por la pieza afectada. En ningún casa pagará Backyard Storage Solu-tions, LLC los gastos de instalación o trabajo manual, o cualquieres otros gastos relacionados a eso.
CondicionesEsta garantía es válida solo cuando:1. La unidad ha sido construida según las instrucciones.2. La unidad ha sido cubierta de tejas y pintada de manera correcta y mantenida regularmente.3. El defecto ocurre mientras la unidad está en la posesión del comprador original.4. Backyard Storage Solutions, LLC ha recibido la tajeta de garantía del producto en el plazo de 30 (treinta) días después de comprar la unidad y después de la noti� cación del defecto por escrito, duranteel período de vigencia de la garantía espe ci� cada arriba.5. Backyard Storage Solutions, LLC ha tenido una oportunidad razonable, durante los sesenta (60) días después de haber recibido la noti� cación, para inspeccionar y averiguar la falla o el defecto antes de comenzar cualquiera reparación.
RequisitosCobertizos de almanacemiento y Casitas de niños
Para dar validez a la garantía, es necesario mantener bien su unidad de Backyard Storage Solutions, LLC: cubrir con tejas el techo, pintar la covertura con un producto 100% de acrílico y de látex para exteriores, usando dos manos de pintura o tinte, como mínimo, en el plazo de sesenta (60) días después de la construcción; masille arriba de todas las puertas y todos los paneles de moldura horizontales y verticales; pinte y selle todos los bordes dispuestos al exterior, los lados y las fachadas del la covertura SmartSide™ y plano, incluyendo todos los muros exteriores y los lados y bordes de las puertas.
Belvederes, Pergolas y Edi� cios de Madera
Para dar validez a la garantía, es necesario mantener bien su inidad. Eso incluye tratar con un preservativo todos los super� cies de cedro y de pino duspuestos al exterior, usando una preservativo para madera, un tinte de aceite semitransparente para exteriores, pintura acrílica de látex para exteriores, o un tinte acrílico de látex de un solo color, en el plazo de treinta (30) días después de con-struir el edi� cio, y luego como sea necesario.
Mantenga corta toda clase de vegetación cerca del edi� cio y asegúrese que la covertura y la moldura no toquen ningúna obra de albañería o el cemento. El margen mínimo entre el suelo y la covertura debe de ser media pulgada (1/2”), con un base de concreto; dos pulgadas y media (2 1/2”) cuando se construye el edi� cio sobre un base de madera (usando un equipo de madera tratada). No se deben usar rociadores cerca de la unidad. En ningún caso será responsable Backyard Storage Solutions, LLC de daños espe-ciales, incidentales, consiguientes o indirectos, ni de fallas causadas por sucesos, hechos u omisiones fuera de nuestro control; eso incluye, pero no está limitado a: el misuso; la construcción incorrecta; cuidado incorrecto (el cual causa, eventualmente, la putre-facción o la descomposición ) y acciones de la naturaleza. Backyard Storage Solutions, LLC no será responsable de ningún gasto de instalación incurrido durante la construcción de la unidad. Esta garantía le de a Ud. ciertos derechos especí� cos que varían de estado a estado.
Para hacer una reclamación:Para hacer una reclamación baja esta garantía, llame al 1-888- 827-9056 o escriba una carta. Favor de tener la siguiente información al llamarnos, o incluirla al escrbirnos:1. El modelo y el tamaño del producto.2. Una lista de las piezas por las cuales hace Ud. la reclamación.3. Prueba de compra del producto, como se muestra en la factura original.4. (Run code) escrita en la tarjeta amarilla de garantía incluida con el producto.
Envíe la información a: Backyard Storage Solutions, LLC Attn: Customer Service 1000 Ternes Monroe, MI 48162 USA
*LAS CONDICIOINES DE LA GARANTIA PUEDEN VARIAR FUERA DE ESTADOS UNIDOSIMPORTANTE: Esta página es su certi� cado de garantía.Favor de llenar completamente y enviar la tarjeta de garantía para dar validez a la garantía. ldr: 03/11/10
Garantía LimitadaCondicional *