2014 12 22 Rebak Publications

1

R. B. Rebak Papers Published in Journals, Book Chapters and Conference Proceedings

in approximate descending chronological order down from December 2014

1. A. Mishra, D. Richesin, and R. B. Rebak, “Localized Corrosion Study of Alloys 718,

625 and C-22HS in Aggressive Corrosive Environments,” Paper C2015-5802,

Corrosion/2015 Conference (NACE International, Houston, TX 2015)

2. Y. J. Kim, F. Wagenbaugh, T. B. Jurewicz, R. J. Blair, and R. B. Rebak, “Environmental

Behavior of Light Water Reactor Accident Tolerant Candidate Cladding Materials under

Design Conditions,” Paper C2015-5817, Corrosion/2015 Conference (NACE

International, Houston, TX 2015)

3. E. C. Hornus, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Effect of

Temperature on the Repassivation Kinetics of Crevice-Corroded Nickel Base Alloys,”

Paper C2015-5739, Corrosion/2015 Conference (NACE International, Houston, TX

2015)

4. M. Kappes, M. Iannuzzi, R. M. Carranza, R. J. Blair, and R. B. Rebak, “Electrochemical

Behavior of Nickel-Containing LAS in Deaerated TM0177 Solution A,” Paper C2015-

5818, Corrosion/2015 Conference (NACE International, Houston, TX 2015)

5. M. Miyagusuku, R. M. Carranza, and R. B. Rebak, “Inhibition Mechanism of Phosphate

Ions on Chloride Induced Crevice Corrosion of Alloy 22,” Corrosion Journal (to be

published)

6. P. A. Martinez, E. C. Hornus, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak,

“Crevice corrosion resistance of super-austenitic and super-duplex stainless steels in

chloride solutions,” Paper C2015-5740, Corrosion/2015 Conference (NACE


7. E. C. Hornus, C. M. Giordano, M. A. Rodríguez, R. M. Carranza, and R. B. Rebak,

“Effect of Temperature on the Crevice Corrosion of Nickel Alloys Containing Chromium

and Molybdenum,” doi: 10.1149/2.0431503jes, J. Electrochem. Soc., vol. 162, issue 3,

C105-C113 (2015)

8. N. S. Zadorozne, C. M. Giordano, R. B. Rebak, A. E. Ares, R. M. Carranza, “Anodic

Stress Corrosion Cracking Susceptibility of Nickel and Nickel-Chromium Alloys

Containing Molybdenum and Iron in Bicarbonate plus Chloride Solutions at 90°C,”

Corrosion Journal (February 2015)

9. R. B. Rebak, “Nuclear Applications of Oxide Dispersion Strengthened and Nano-

Featured Alloys: An Introduction,” JOM, Vol. 66, No. 12, 2014

10. R. B. Rebak “Advanced Steels for Accident Tolerant Fuel Cladding in Current Light

Water Reactors,” TMS John Wiley and Sons, proceedings from the conference Energy

Materials 2014, Xi’an, China, 04-06 November 2014.

11. R. B. Rebak, P. L. Andresen, Y. J. Kim, and E. J. Dolley, “Characterization of Advanced

Steels as Accident Tolerant Fuel Cladding for Light Water Reactors,” in Proceedings of

2

the IAEA Technical Meeting “Accident Tolerant Fuel Concepts For Light Water

Reactors” Oak Ridge, TN, 13-16 October 2014.

12. R. B. Rebak, M. Rincon Ortiz, M. Iannuzzi, M. Kappes, A. Mishra, and M. A.

Rodriguez, “Effect of thermal treatment on the localized corrosion behaviour of alloy

718,“ Paper 7284, Eurocorr 2014, Pisa, Italy, 08-12 September 2014.

13. R. B. Rebak, and E. J. Dolley, “Effect of Superheated Steam on the Corrosion Behaviour

of Advanced Steels Proposed as Accident Tolerant Fuel Cladding,“ Paper 7283, Eurocorr

2014, Pisa, Italy, 08-12 September 2014.

14. M. Kappes, M. Iannuzzi, R. B. Rebak, and R. M. Carranza, “Sulfide stress cracking of

nickel-containing low-alloy steels,” Corrosion Reviews, 32(3-4): 101–128 (2014)

15. P. L. Andresen, R. B. Rebak, and E. J. Dolley “SCC Resistance of Irradiated and

Unirradiated High Cr Ferritic Steels,” Paper C2014-3760, Corrosion/2014 Conference

(NACE International, Houston, TX 2014)

16. M. Rincon Ortiz, M. Iannuzzi, M. Kappes, R. B. Rebak, and R. M. Carranza “Selecting

corrosion resistant alloys for seawater applications,” Research in Progress Symposium,

Paper C-2014-5139, Corrosion/2014 Conference (NACE International, Houston, TX

2014)

17. E. J. Dolley, P. L. Andresen, M. M. Morra, X. Lou, and R. B. Rebak, “Cracking

Resistance of Chromium Rich Alloys in High Temperature Water,” Paper C2014-4293,

Corrosion/2014 Conference (NACE International, Houston, TX 2014)

18. R. B. Rebak, R. J. Blair, P. J Martiniano, F. Wagenbaugh, and E. J. Dolley, “Resistance

of Advanced Steels to Reaction with High Temperature Steam as Accident Tolerant Fuel

Cladding Materials,” Paper C2014-3924, Corrosion/2014 Conference (NACE


19. X. Lou and R. B. Rebak, “Corrosion and Flow Accelerated Corrosion of Candidate

Coatings for Seawater Cooled Heat Exchanger,” Paper C2014-4328, Corrosion/2014

Conference (NACE International, Houston, TX 2014)

20. M. L. Ungaro, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Electrochemical

Noise Study of Chloride-Induced Crevice Corrosion on Ni-Cr-Mo Alloys,” Paper C2014-

3904, Corrosion/2014 Conference (NACE International, Houston, TX 2014)

21. R. B. Rebak, “Materials in Nuclear Waste Disposition,” JOM, Vol. 66, No. 3, 2014

22. N. S. Zadorozne, C. M. Giordano, R. M. Carranza, A. E. Ares, and R. B. Rebak, “Stress

Corrosion Cracking of Nickel Alloys in Bicarbonate Solutions,” Paper 1163 in

proceedings of Eurocorr 2013, Estoril, Portugal, 01-05 September 2013

23. J. F. Flores, E. J. Dolley, and R. B. Rebak, “Environmental and Mechanical Behavior of

Ferritic Chromium Steels in High Temperature Water and Steam,” Paper 3437 in 16th

Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors,

Asheville, NC, USA, 11-15 August 2013

24. E. J. Dolley, P. L. Andresen, R. B. Rebak, M. M. Morra, X. Lou, “SCC Performance of

Alternative BWR Structural Materials with Varying Chromium Concentrations,” Paper

3

3124 in 16th Environmental Degradation of Materials in Nuclear Power Systems – Water

Reactors, Asheville, NC, USA, 11-15 August 2013

25. R. B. Rebak, “Introduction to Energy Production,” JOM, Vol. 65, No. 8, 2013

26. M. Rincon Ortiz, M. A. Rodríguez, R. M. Carranza, and R. B. Rebak, “Oxyanions as in-

hibitors of chloride-induced crevice corrosion of Alloy 22,” Corrosion Science, vol. 68

March, 2013. p. 72-83

27. N. S. Zadorozne, C. M. Giordano, R. M. Carranza, A. E. Ares, and R. B. Rebak,

“Susceptibility of Nickel Alloys to Environmental Cracking in Bicarbonate Containing

Aqueous Solutions,” Paper 3438 in in 16th Environmental Degradation of Materials in

Nuclear Power Systems – Water Reactors, Asheville, NC, USA, 11-15 August 2013

28. M. A. Othon, M. M. Morra, S. Ooki, and R. B. Rebak, “Assessing Residual Strains in

Nuclear Power Reactor Internal Components Weld Mockups of Nickel Alloys using

EBSD,” Paper PVP2013-97350, in 2013 ASME PVP Conference Integrity Issues in SCC

and Corrosion Fatigue, 14-18 July 2013, Paris, France

29. R. B. Rebak, “Resistance of Ferritic Steels to Stress Corrosion Cracking in High

Temperature Water,” Paper PVP2013-97352, in 2013 ASME PVP Conference Integrity

Issues in SCC and Corrosion Fatigue, 14-18 July 2013, Paris, France


“Effect of Temperature on Crevice Corrosion Susceptibility of Nickel Alloys for Nuclear

Repositories,” Paper 2504, , Corrosion/2013, Orlando, FL, 17-21 March 2013 (NACE

International, Houston TX)

31. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Mechanisms of inhibition of the

chloride-induced crevice corrosion of Alloy 22,” Paper 2633, Corrosion/2013, Orlando,

FL, 17-21 March 2013 (NACE International, Houston TX).

32. R. B. Rebak, “Susceptibility of Engineering Alloys to Environmentally Assisted

Cracking in Nuclear Waste Repositories Environments,” Paper 2597, Corrosion/2013,

Orlando, FL, 17-21 March 2013 (NACE International, Houston TX).

33. R. B. Rebak, P. L. Andresen, R. J. Blair and E. J. Dolley, “Environmentally Assisted

Cracking Resistant Ferritic Steels for Light Water Reactor Applications,” Paper 2599,

Corrosion/2013, Orlando, FL, 17-21 March 2013 (NACE International, Houston TX).


“Effect of Temperature on the Crevice Corrosion Susceptibility of Passivating Nickel

Alloys,” in Ceramic Transactions Volume 241, Advances in Materials Science for

Environmental and Energy Technologies II, proceedings from 2012 Materials Science

and Technology (MS&T’12) symposia, editors Josef Matyas, Tatsuki Ohji, Xingbo Liu,

Mariappan Paranthaman, Ram Devanathan, Kevin Fox, Mrityunjay Singh, and Winnie

Wong-Ng, (Ceramic Transactions, July 2013).

35. R. B. Rebak, “Environmentally Assisted Cracking of Nickel Alloys in Nuclear Power

Generation and Nuclear Waste Disposal,” Paper 1712, Eurocorr 2012, Istanbul, Turkey,

09-13 September 2012

4

36. N. S. Zadorozne, C. M. Giordano, M. A. Rodríguez, R. M. Carranza, and R. B. Rebak,

“Crevice Corrosion Kinetics of Nickel Alloys Bearing Chromium and Molybdenum,”

Electrochimica Acta, vol. 76 August 1, 2012. p. 94-101

37. R. B. Rebak, “Stress Corrosion Cracking,” book chapter in “Corrosion in Nuclear Waste

Systems,” edited by F. King and to be published by John Wiley & Sons, Inc

38. R. B. Rebak, “Crystalline Materials: Nickel,” book chapter 7 in Environmental

Degradation of Advanced and Traditional Engineering Materials, edited by L. H. Hihara,

R. P. I. Adler and R. M. Latanision, accepted for publication by Taylor & Francis Books,

Inc.

39. M. Miyagusuku, R. M. Carranza, R. B. Rebak, “Estudio de productos de corrosión de la

aleación 22 por SEM/EDS,” SAMIC 2012, 2do Congreso Argentino de Microscopía, 18

a 20 de Abril 2012, Buenos Aires, Argentina

40. P. L. Andresen, T. B. Jurewicz, and R. B. Rebak, “Stress Corrosion Cracking Resistance

of Ferritic Chromium Steels in High Temperature Water,” Paper C2012-0001181,

Corrosion/2012, Salt Lake City - UT, 11-15 March 2012 (NACE International, Houston

TX)

41. N. S. Zadorozne, R. M. Carranza, C. M. Giordano, A. E. Ares, and R. B. Rebak,

“Anodic Behavior of Nickel base Alloys in Media Containing Bicarbonate and Chloride

Ions,” Paper C2012-0001413, Corrosion/2012, Salt Lake City - UT, 11-15 March 2012

(NACE International, Houston TX)

42. G. Sundararajan, A. J. Kulkarni, and R. B. Rebak, “Electrochemical and Environmental

Behavior of Protective Coatings,” Paper C2012-0001388, Corrosion/2012, Salt Lake City

- UT, 11-15 March 2012 (NACE International, Houston TX)

43. S. Sosa Haudet, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Effect of Alloy

Composition on the Crevice Corrosion Resistance of Nickel Alloys,” Paper C2012-

0001455, Corrosion/2012, Salt Lake City - UT, 11-15 March 2012 (NACE International,

Houston TX)

44. R. B. Rebak, “Sulfidic Corrosion in Refineries – A Review,” Corrosion Reviews, Vol.

29, pp. 123–133 (2011)

45. N. S. Zadorozne, R. M. Carranza, C. M. Giordano, A. E. Ares, and R. B. Rebak, “Effect

of the Composition of Nickel Alloys on the Anodic Behavior in Aqueous Solutions of

Chloride and Bicarbonate,” Vol. 1475, XXXV International Symposium "Scientific Basis

for Nuclear Waste Management,” Materials Research Society, Buenos Aires, Argentina,

October 2 - 7, 2011

46. R. B. Rebak, “Environmentally Assisted Cracking Research of Engineering Alloys for

Nuclear Waste Repository Containers,” Vol. 1475, XXXV International Symposium

"Scientific Basis for Nuclear Waste Management,” Materials Research Society, Buenos

Aires, Argentina, October 2 - 7, 2011

47. M. Rincon Ortiz, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Efficiency of

inhibitors for chloride-induced crevice corrosion of Alloy 22,” Vol. 1475, XXXV

International Symposium "Scientific Basis for Nuclear Waste Management,” Materials

Research Society, Buenos Aires, Argentina, October 2 - 7, 2011

5

48. M. Miyagusuku, R. M. Carranza, and R. B. Rebak, “Phosphate Inhibition Effect on

Chloride-Induced Crevice Corrosion of Alloy 22,” Vol. 1475, XXXV International

Symposium "Scientific Basis for Nuclear Waste Management,” Materials Research

Society, Buenos Aires, Argentina, October 2 - 7, 2011

49. R. B. Rebak, “Stress Corrosion Cracking of Nickel Based Alloys,” Chapter 7 in Stress

Corrosion Cracking, edited by V.S. Raja, T. Shoji and S. Lynch, pp. 273-306 (Woodhead

Publishing, Oxford, 2011).

50. M. Miyagusuku, R. M. Carranza, and R. B. Rebak, “Inhibition Effect of Phosphate Ions

on Crevice Corrosion of Alloy 22,” Paper 11202 in Corrosion/2011, 13-17 March 2011

Houston, TX (NACE International, 2011: Houston, TX)

51. J. Kaneda, M. Koshiishi, M. M. Morra, and R. B. Rebak, “Microstructural

Characterization of Surface Modified Alloy 82 Welds Regarding Susceptibility to

Environmentally Assisted Cracking,” Paper 11213 in Corrosion/2011, 13-17 March 2011

Houston, TX (NACE International, 2011: Houston, TX)

52. R. B. Rebak, “Electrochemical Behavior of Silicon Modified Stainless Steels in High

Temperature,” Paper 11214 in Corrosion/2011, 13-17 March 2011 Houston, TX (NACE

International, 2011: Houston, TX)

53. M. Rincón Ortíz, M. A. Rodríguez, R. M. Carranza, and R. B. Rebak, “Efficiency of

Inhibitors of Chloride-Induced Crevice Corrosion of a Ni-Cr-Mo Alloy,” Paper 11204 in

Corrosion/2011, 13-17 March 2011 Houston, TX (NACE International, 2011: Houston,

TX)

54. C. M. Giordano, M. Rincon Ortız, M. A. Rodrıguez, R. M. Carranza, and R. B. Rebak,

“Crevice Corrosion Testing Methods for Measuring Repassivation Potential of Alloy 22,”

Corrosion Engineering, Science and Technology, Vol. 46, No 2, pp.129-133 (2011).

55. R. B. Rebak, “Materials and Corrosion Research in the Yucca Mountain Project,” The

Electrochemical Society Transactions, pp. 1-14, 218th ECS Meeting Vol. 33, Issue 25 -

October 10 - 15, 2010 , Las Vegas, NV “Corrosion Issues in Nuclear Waste Storage: A

Symposium in Honor of the 65th Birthday of David Shoesmith,” Editors: J. Noël, X. He,

and Z. Aguilar.

56. R. B. Rebak, “Environmental Degradation of Engineered Barrier Materials in Nuclear

Waste Repositories,” Chapter 36 in Uhlig’s Handbook, edited by W. Revie, pp. 503-516

(Wiley & Sons 2011).

57. M. Rincon Ortiz, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Determination of

crevice corrosion susceptibility of Alloy 22 using different electrochemical techniques,”

in Scientific Basis for Nuclear Waste Management XXXIV, Vol. 1265, pp. 203-208

(Materials Research Society, Warrendale, PA 2010).

58. R. B. Rebak, “Advances in Materials Corrosion Research in the Yucca Mountain

Project,” Chapter 21 in Advances in Materials Science for Environmental and Nuclear

Technology II, Vol. 227, Editors; K. Sundaram, K. Fox, T. Ohji, and E. Hoffman,

Ceramic Transactions (2011).

6

59. N. S. Zadorozne, C. M. Giordano, M. A. Rodriguez, R. M. Carranza, N. S. Meck, and R.

B. Rebak, “Effect of age hardening on the crevice corrosion resistance of Ni Cr Mo

alloys,” published by the European Federation of Corrosion Event 324 (2010)

60. R. B. Rebak, “Environmentally Assisted Cracking Behavior of Nickel Alloys in Oil and

Gas Applications: A Review,” published by the European Federation of Corrosion Event

324 (2010)

61. M. Rincon Ortiz, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Determination of

the Crevice Corrosion Stabilization and Repassivation Potentials of a Corrosion Resistant

Alloy,” Corrosion, Vol. 66, No. 10, pp. 105002-1 to 105002-12 (2010)

62. Y. -J. Kim, R. B. Rebak, Y.-P. Lin, D. Lutz, D. Crawford, A. Kucuk, and B. Cheng,

“Photoelectrochemical Investigation of Radiation-Enhanced Shadow Corrosion

Phenomenon,” Journal of ASTM International, Vol. 7, No. 7, Paper ID JAI102952 (2010)

63. N. S. Zadorozne, R. M. Carranza, M. A. Rodriguez, N. S. Meck, and R. B. Rebak,

“Corrosion resistance of Ni-Cr-Mo and Ni-Mo-Cr alloys in different metallurgical

conditions,” Paper 10236 in Corrosion/2010, 14-18 March 2010 San Antonio, TX

(NACE International, 2010: Houston, TX)

64. M. Rincon Ortiz, M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Crevice

Corrosion Repassivation of Alloy 22 in Chloride Solutions,” Paper 10237 in

Corrosion/2010, 14-18 March 2010 San Antonio, TX (NACE International, 2010:

Houston, TX)

65. M. Miyagusuku, R. B. Rebak, and R. M. Carranza, “The Effect of Phosphate Ions on the

Corrosion Behavior of Alloy 22,” Paper 10238 in Corrosion/2010, 14-18 March 2010 San

Antonio, TX (NACE International, 2010: Houston, TX)

66. P. H. Chou, P. L. Andresen, M. L. Pollick, and R. B. Rebak, “Repassivation Behavior

and Stress Corrosion Cracking Susceptibility of Stainless Steels Containing Silicon,”

Paper 10285 in Corrosion/2010, 14-18 March 2010 San Antonio, TX (NACE

International, 2010: Houston, TX)

67. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Effect of pH and Temperature on

the Corrosion Potential of Alloy 22 in Aerated Solutions” Paper 10240 in

Corrosion/2010, 14-18 March 2010 San Antonio, TX (NACE International, 2010:

Houston, TX)

68. R. B. Rebak, “Comparative Nuclear Power Plant Performance of Stabilized and Non-

Stabilized Austenitic Stainless Steels,” in 2010 TMS Annual Meeting Seattle, WA, 14-18

February 2010

69. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Effect of Potential on Crevice

Corrosion Kinetics of Alloy 22,” Corrosion, Vol. 66, No. 1, pp. 015007-015007-14

(2010)

70. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Passivation and Depassivation of

Alloy 22 in Acidic Chloride Solutions,” Journal of The Electrochemical Society, Vol.

157 No. 1, pp.C1-C8 (2010)

7

71. R. B. Rebak, “Materials for the nuclear renaissance: Foreword,” Metallurgical and

Materials Transactions A, Vol. 40, No. 12, pp. 2802 (2009)

72. P. L. Andresen, P. H. Chou, M. M. Morra, J. L. Nelson, and R. B. Rebak,

“Microstructural and stress corrosion cracking characteristics of austenitic stainless steels

containing silicon,” Metallurgical and Materials Transactions A, Vol. 40, No. 12, pp.

2824-2836 (2009)

73. R. M. Carranza, M. Miyagusuku, and R. B. Rebak, “Efecto Inhibidor de los Iones

Fosfatos en la Corrosion de la Aleacion 22,” in proceedings of the 9th

International

Congress of Materials organized by the Sociedad Argentina de Materiales (SAM) and the

Sociedad Chilena de Materiales (SOCHIM), 19-23 October 2009, Buenos Aires,

Argentina

74. P. L. Andresen, P. H. Chou, M. L. Pollick, J. L. Nelson, and R. B. Rebak, “Passivation

Characteristics of Stainless Steels Containing Silicon,” Paper 203007 in the proceedings

of the 14th

International Conference on Environmental Degradation of Materials in

Nuclear Power Systems-Water Reactors, 23-27 August 2009 in Virginia Beach, VA (to

be published by the American Nuclear Society)

75. R. M. Carranza, M. Rincón Ortíz, M. A. Rodríguez, and R. B. Rebak, “Corrosion

Resistance of Alloy 22 in Chloride Plus Silicate Solutions,” Paper 203176 in the

proceedings of the 14th

International Conference on Environmental Degradation of

Materials in Nuclear Power Systems-Water Reactors, 23-27 August 2009 in Virginia

Beach, VA (to be published by the American Nuclear Society)

76. R. B. Rebak, Y.-P. Lin, and Y.-J. Kim, “Review on Electrochemical Corrosion of

Zirconium Alloys in High Temperature Water,” in the proceedings of the 14th

International Conference on Environmental Degradation of Materials in Nuclear Power

Systems-Water Reactors, 23-27 August 2009, Virginia Beach, VA, 2; 1400-1406

(American Nuclear Society, 2009)

77. J. Farmer, J.-S. Choi, C. Saw, J. Haslam, D. Day, P. Hailey, T. Lian, R. Rebak, J.

Perepezko, J. Payer, D. Branagan, B. Beardsley, A. D'Amato, L. Aprigliano, “Iron-Based

amorphous metals: High-performance corrosion-resistant material development,”

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science,

Vol. 40, No. 6, pp. 1289-1305 (2009)

78. R. M. Carranza and R. B. Rebak, “Anionic and Cationic Effects on the Crevice

Corrosion Susceptibility of Alloy 22,” in Scientific Basis for Nuclear Waste Management

XXXIII, Vol. 1193, pp. 569-576 (Materials Research Society, Warrendale, PA 2009).

79. R. B. Rebak, “Corrosion testing of nickel and titanium alloys for nuclear waste

disposition,” Corrosion, 65, No. 4, pp. 252-271 (2009)

80. R. M. Carranza, C. M. Giordano, M. A. Rodriguez and R. B. Rebak, “Electrochemical

Methods for Repassivation Potential Measurements,” in Corrosion/2009 NACE

International Conference and Exhibition, 22-26 March 2009 in Atlanta, GA (NACE

International, 2009: Houston TX)

81. R. B. Rebak; R. M. Carranza; M. A. Rodriguez, “The Corrosion Potential of Welded and

Thermally Aged Alloy 22 in Aerated Aqueous Solutions,” Paper 09429 in

8

Corrosion/2009 NACE International Conference and Exhibition, 22-26 March 2009 in

Atlanta, GA (NACE International, 2009: Houston TX)

82. Y.-J. Kim; and R. B. Rebak, “Photoelectrochemistry of Zirconium Alloys in High

Temperature Water,” Paper 09417 in Corrosion/2009 NACE International Conference

and Exhibition, 22-26 March 2009 in Atlanta, GA

83. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Crevice Corrosion of Alloy 22 at

the Open Circuit Potential in Hot Chloride Solutions,” in Corrosion/2009, 22-26 March

2009 in Atlanta, GA (NACE International, 2009: Houston TX)

84. R. B. Rebak, “Stifling of Crevice Corrosion in Alloy 22 During Constant Potential

Tests,” ASME Journal of Pressure Vessel Technology, February 2009, Vol. 131, Issue 1

85. N. C. Hyatt, D. A. Pickett, and R. B. Rebak, “Materials Research Society Symposium Q

Scientific Basis for Nuclear Waste Management Proceedings: Preface,” Vol. 1124, pp.

xvii (Materials Research Society, 2009; Warrendale, PA)

86. R. B. Rebak, “General Corrosion Behavior of N06022 in Super Concentrated Brines at

Temperatures Higher than 100°C,” paper Q9.6 presented at the XXXII Symposium on

Scientific Basis for Nuclear Waste Management as part of the Fall 2008 MRS meeting,

Boston 01-05 December 2008, Vol. 1124, pp. 473-480 (Materials Research Society,

2009; Warrendale, PA)

87. M. A. Rodríguez, R. M. Carranza, and R. B. Rebak, “Effect of Fluoride Ions on the

Passivity and Chloride-Induced Crevice Corrosion of Alloy 22,” paper Q9.8 presented at

the XXXII Symposium on Scientific Basis for Nuclear Waste Management as part of the

Fall 2008 MRS meeting, Boston 01-05 December 2008, Vol. 1124, pp. 487-492

(Materials Research Society, 2009; Warrendale, PA)

88. K. G. Mon and R. B. Rebak, “Effect of Chemistry Variations of Wrought N06022 on the

Repassivation Potential in 1 M NaCl at 90°C,” Paper PVP2008-61269 in the proceedings

of the PVP2008 ASME Pressure Vessels and Piping Division Conference, 27-31 July

2008, Chicago, IL (ASME, 2008, New York, NY)

89. R. B. Rebak, “The Long-Term Environmental Degradation of Zirconium Alloys in

Contact with Spent Nuclear Fuel – A Review,” Paper PVP2008-61272 in the proceedings

of the PVP2008 ASME Pressure Vessels and Piping Division Conference, 27-31 July

2008, Chicago, IL (ASME, 2008, New York, NY)

90. R. M. Carranza, C. M. Giordano, M. A. Rodríguez, and R. B. Rebak, “Effect of Organic

Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in

Chloride Solutions,” Paper 08578 in Corrosion/2008 Conference and Exhibition, 16-20

March 2008 in New Orleans, LA (NACE International, 2008: Houston, TX)

91. R. M. Carranza, M. A. Rodríguez, and R. B. Rebak, “Anodic and Cathodic Behavior of

Mill Annealed and Topologically Closed Packed Alloy 22 in Chloride Solutions,” Paper

08579 in Corrosion/2008 Conference and Exhibition, 16-20 March 2008 in New Orleans,

LA (NACE International, 2008: Houston, TX)

92. R. M. Carranza, C. M. Giordano, M. A. Rodriguez, and R. B. Rebak, “Effect of weak

acid additions on the general and localized corrosion susceptibility of alloy 22 in chloride

solutions,” in Symposium Scientific Basis for Nuclear Waste Management XXXI,

9

Materials Research Society Symposium Proceedings, Vol. 1107, pp. 511-518 (MRS,

2008: Warrendale, PA)

93. R. B. Rebak , G. O. Ilevbare, and R. M. Carranza, “Repassivation potential of Alloy 22

in sodium and calcium chloride brines,” in Symposium Scientific Basis for Nuclear

Waste Management XXXI, Materials Research Society Symposium Proceedings, Vol.

1107, pp. 511-518 (MRS, 2008: Warrendale, PA)

94. T. Lian, G. E. Gdowski, P. D. Hailey, and R. B. Rebak, “Crevice corrosion resistance of

Alloy 22 in high-nitrate, high-temperature dust deliquescence environments,” Corrosion,

Vol. 64, No. 7, pp. 613-623 (2008)

95. D. V. Fix and R. B. Rebak, “The long-term corrosion test facility at Lawrence Livermore

National Laboratory,” American Society of Mechanical Engineers, Pressure Vessels and

Piping Division (Publication) PVP 7, pp. 425-431 (2008)

96. M. A. Rodriguez, R. M. Carranza, M. L. Stuart, and R. B. Rebak, “Long-term corrosion

potential behavior of alloy 22 in hot 5 m CaCl2 + 5m Ca(NO3)2 brines,” American

Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication)

PVP 7, pp. 395-404 (2008)

97. T. Lian, G. E. Gdowski, P. D. Hailey, and R. B. Rebak, “Crevice repassivation potential

of alloy 22 in high-nitrate dust deliquescence type environments,” American Society of

Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP 7, pp.

413-423 (2008)

98. R. B. Rebak, S. D. Day, T. Lian, L. F. Aprigliano, P. D. Hailey, and J. C. Farmer,

“Enhanced corrosion resistance of iron-based amorphous alloys,” American Society of


433-441 (2008)

99. K. J. Evans, M. L. Stuart, P. D. Hailey, and R. B. Rebak, “Long-term immersion testing

of alloy 22 and titanium grade 7 double u-bend specimens,” American Society of


405-412 (2008)

100. K. J. Evans and R. B. Rebak, “Anodic polarization behavior of titanium grade 7 in dust

deliquescence salt environments,” American Society of Mechanical Engineers, Pressure

Vessels and Piping Division (Publication) PVP 7, pp. 387-394 (2008)

101. R. B. Rebak, “Materials issues for advanced nuclear systems,” Metallurgical and

Materials Transactions A: Physical Metallurgy and Materials Science, Vol. 39, No. 2,

pp. 211 (2008)

102. J. C. Farmer, J.-S. Choi, C.-K. Saw, R. B. Rebak, S. D. Day, T. Lian, P. D. Hailey, J. H.

Payer, D. J. Branagan, and L. F. Aprigliano, “Corrosion resistance of amorphous

Fe49.7Cr17.7 Mn1.9Mo7.4W1.6B15.2 C3.8Si2.4 Coating: A new criticality control material,”

Nuclear Technology, Vol. 161, No. 2, February 2008, pp. 169-189 (2008)

103. R. B. Rebak, S. D. Day, T. Lian, P. D. Hailey, and J. C. Farmer, “Environmental testing

of iron-based amorphous alloys,” Metallurgical and Materials Transactions A: Physical

Metallurgy and Materials Science, Vol. 39, No. 2, pp. 225-234 (2008)

10

104. R. B. Rebak, “Material corrosion issues for nuclear waste disposition in Yucca

Mountain,” Journal of Metals, Vol. 60, No. 1, pp. 40-43 (2008)

105. J. C. Estill and R. B. Rebak, “Anodic behavior of specimens prepared from a full-

diameter Alloy 22 fabricated mockup container for nuclear waste,” Journal of Pressure

Vessel Technology, Transactions of the ASME, Vol. 129, No. 4, November 2007, pp.

729-736

106. L. F. Aprigliano, S. D. Day, J. J. Haslam, J. C. Farmer, and R. B. Rebak, “Industrial salt

fog testing of a SAM2X5 coated stainless steel cylinder,” in Materials Science and

Technology Conference and Exhibition, MS&T’07 - "Exploring Structure, Processing,

and Applications Across Multiple Materials Systems" Vol. 4, pp. 2297-2304 (2007)

107. S. D. Day, J. J. Haslam, J. C. Farmer, and R. B. Rebak, “Dissolution modes and effect of

high temperature aging on the corrosion resistance of iron based amorphous alloys,”

Materials Science and Technology Conference and Exhibition, MS&T’07 - "Exploring

Structure, Processing, and Applications Across Multiple Materials Systems,” Vol. 4, pp.

2411-2423 (2007)

108. S. D. Day, T. Lian, J. C. Farmer, and R. B. Rebak, “Cyclic and linear polarization of

yttrium containing iron-based amorphous alloys,” Materials Science and Technology

Conference and Exhibition, MS&T’07 - "Exploring Structure, Processing, and

Applications Across Multiple Materials Systems,” Vol. 4, Pages 2361-2372 (2007)

109. J. Farmer, J. Haslam, S. Day, T. Lian, C.-K. Saw, P. Hailey, J.-S. Choi, R. Rebak, J.

Payer, C. Blue, W. Peters, and D. Branagan, “The corrosion resistance of Fe-based

amorphous metals: Fe49.7Cr17.7Mn1.9Mo7.4W1.6B15.2C3.8Si2.4 and other compositions,”

Materials Science and Technology Conference and Exhibition, MS&T’07 - "Exploring

Structure, Processing, and Applications Across Multiple Materials Systems,” Vol. 4, pp.

2285-2296 (2007)

110. P. D. Hailey, J. C. Farmer, S. D. Day, and R. B. Rebak, “Anodic behavior of SAM2×5

material applied as amorphous coatings,” Materials Science and Technology Conference

and Exhibition, MS&T’07 - "Exploring Structure, Processing, and Applications Across

Multiple Materials Systems,” Vol. 4, pp. 2398-2410 (2007)

111. K. J. Evans and R. B. Rebak, “Measuring the Repassivation Potential of Alloy 22 Using

the Potentiodynamic – Galvanostatic – Potentiostatic Method,” Journal of ASTM

International, Vol. 4, No. 9, Paper ID JAI101230 as proceedings of the Symposium on

Advances in Electrochemical Techniques for Corrosion Monitoring and Measurement,

22-23 May 2007 in Norfolk, VA

112. R. M. Carranza, M. A. Rodriguez and R. B. Rebak “Effect of Fluoride Ions on the

Crevice Corrosion and Passive Behavior of Alloy 22 in Hot Chloride Solutions,”

Corrosion, Vol. 63, No. 5, 480 (2007)

113. R. B. Rebak, “Environmental Degradation of Materials for Nuclear Waste Repositories

Engineered Barriers,” Advances in Materials Science, Vol. 7, No. 2 (2007)

114. J. Lamb, V. Arjunan, V. Deodeshmukh, D. Chandra, J. Daamen, and R. B. Rebak,

“Hydrogen Diffusion and Trapping Effects in Low and Medium Carbon Steels for

11

Subsurface Reinforcement in the Proposed Yucca Mountain Repository,” Metallurgical

and Materials Transactions A, 38A, 348-355 (2007)

115. R. M. Carranza, M. A. Rodriguez and R. B. Rebak, “Environmental and Geometrical

Conditions to Sustain Crevice Corrosion in Alloy 22,” paper 07581 in proceedings of the

NACE International Corrosion/2007 Conference and Exposition, 11-15 March 2007,

Nashville, TN

116. R. B. Rebak, K. J. Evans and G. O. Ilevbare, “Crevice Repassivation Potential of Alloy

22 in Simulated Concentrated Ground Waters,” paper 07584, in proceedings of the

NACE International Corrosion/2007 Conference and Exposition, 11-15 March 2007,

Nashville, TN

117. M. A. Rodriguez, M. L. Stuart and R. B. Rebak, “Long-Term Electrochemical Behavior

of Creviced and Non-Creviced Alloy 22 in CaCl2 + Ca(NO3)2 Brines at 155°C,” paper

07577 in proceedings of the NACE International Corrosion/2007 Conference and

Exposition, 11-15 March 2007, Nashville, TN

118. N. S. Meck, P. Crook and R. B. Rebak, “The Influence of Composition upon Surface

Degradation and Stress Corrosion Cracking of the Ni-Cr-Mo Alloys in Wet Hydrofluoric

Acid,” paper 07481 in proceedings of the NACE International Corrosion/2007

Conference and Exposition, 11-15 March 2007, Nashville, TN.

119. R. B. Rebak, “Environmental Cracking of Corrosion Resistant Alloys in the Chemical

Process Industry – A Review,” paper 07480 in proceedings of the NACE International

Corrosion/2007 Conference and Exposition, 11-15 March 2007, Nashville, TN

120. R. B. Rebak, L. F. Aprigliano, S. D. Day, J. J. Haslam and J. C. Farmer, “Salt-Fog

Testing of Iron-Based Amorphous Alloys,” paper NN3.14, in proceedings of the

Materials Research Society Fall Meeting, 27 November to 01 December 2006, Boston

Massachusetts, Materials Research Society Symposium Proceedings, Vol. 985, pp. 321-

326 (2007)

121. J. Farmer, J. Haslam, D. Day, T. Lian, C. Saw, P. Hailey, J.-S. Choi, R. Rebak, N. Yang,

R. Bayles, L. Aprigliano, J. Payer, J. Perepezko, K. Hildal, E. Lavernia, L. Ajdelsztajn,

D. Branagan, B. Beardsley, “A high-performance corrosion-resistant iron-based

amorphous metal-the effects of composition, structure and environment on corrosion

resistance,” Materials Research Society Symposium Proceedings, Vol. 985, pp. 255-260

(2007)

122. K. J. Evans and R. B. Rebak, “Repassivation Potential of Alloy 22 in Chloride plus

Nitrate Solutions Using the Potentiodynamic-Galvanostatic-Potentiostatic Method,”

paper NN3.13 in proceedings of the Materials Research Society Fall Meeting, 27

November to 01 December 2006, Boston Massachusetts, Materials Research Society

Symposium Proceedings, Vol. 985, pp. 313-320 (2007)

123. R. B. Rebak, “Mechanisms of Inhibition of Crevice Corrosion in Alloy 22,” paper

NN8.4 in proceedings of the Materials Research Society Fall Meeting, 27 November to

01 December 2006, Boston Massachusetts, Materials Research Society Symposium

Proceedings, Vol. 985, pp. 261-268 (2007)

12

124. R. M Carranza, M. A. Rodriguez and R. B. Rebak, “Oxide Film Aging on Alloy 22 in

Halide Containing Solutions,” paper NN8.9 in proceedings of the Materials Research

Society Fall Meeting, 27 November to 01 December 2006, Boston Massachusetts,

Materials Research Society Symposium Proceedings, Vol. 985, pp. 287-292 (2007)

125. R. B. Rebak, R. A. Etien, S. R. Gordon and G. O. Ilevbare, “Influence of Black

Annealing Oxide Scale on the Anodic Behavior of Alloy 22,” Corrosion, Vol. 62, No. 11,

pp. 967-980 (2006)

126. D. V. Fix and R. B. Rebak, “Impact of Small Chemistry Variations in Plate and Weld

Filler Metal on the Corrosion Performance of Ni-Cr-Mo Alloys,” Journal of ASTM

International, Vol. 3, Issue 10, November/December 2006

127. R. B. Rebak, “Selection of Corrosion Resistant Materials for Nuclear Waste

Repositories,” in proceedings of the MS&T’06 Conference, 15-19Oct06, Cincinnati, OH

128. R. B. Rebak, “Corrosion Engineers and Nuclear Waste Disposition,” Materials

Performance, Vol. 45, No. 9, p. 8 (2006)

129. R. B. Rebak and R. Daniel McCright, “Corrosion of Containment Materials for

Radioactive-Waste Isolation,” in Metals Handbook, Volume 13C “Corrosion: Materials,

pp. 421-437 (ASM International, 2006: Metals Park, OH)

130. S. D. Day, F. M. G. Wong, S. R. Gordon, L. L. Wong, and R. B. Rebak,

“Electrochemical Testing of Gas Tungsten Arc Welded and Reduced Pressure Electron

Beam Welded Alloy 22,” Paper 93730 in the Proceedings of PVP2006-ICPVT-11, 2006

ASME Pressure Vessels and Piping Division Conference, July 23-27, 2006, Vancouver,

BC, Canada

131. G. O. Ilevbare, R. A. Etien, J. C. Estill, G. A. Hust, A. Yilmaz, M. L. Stuart, and

R. B. Rebak, “Anodic Behavior of Alloy 22 in High Nitrate Brines at Temperatures

Higher than 100°C,” Paper 93423 in the Proceedings of PVP2006-ICPVT-11, 2006

ASME Pressure Vessels and Piping Division Conference, July 23-27, 2006, Vancouver,

BC, Canada

132. J. C. Estill, G. A. Hust, K. J. Evans, M. L. Stuart, and R. B. Rebak, “Long-Term

Corrosion Behavior of Alloy 22 in 5 M CaCl2 at 120°C,” Paper 93422 in the Proceedings

of PVP2006-ICPVT-11, 2006 ASME Pressure Vessels and Piping Division Conference,

July 23-27, 2006, Vancouver, BC, Canada

133. L. L. Wong, S. I. Martin, and R. B. Rebak, “Methods to Calculate Corrosion Rates for

Alloy 22 from Polarization Resistance Experiments,” Paper 93421 in the Proceedings of

PVP2006-ICPVT-11, 2006 ASME Pressure Vessels and Piping Division Conference,

July 23-27, 2006, Vancouver, BC, Canada

134. T. Lian, T. Yashiki, T. Nakayama, T. Nakanishi, and R. B. Rebak, “Comparative

Corrosion Behavior of Two Palladium-Containing Titanium Alloys,” Paper 93418 in the

Proceedings of PVP2006-ICPVT-11, 2006 ASME Pressure Vessels and Piping Division

Conference, July 23-27, 2006, Vancouver, BC, Canada

135. D. V. Fix and R. B. Rebak, “Effect of Chemistry Variations in Plate and Weld Filler

Metal on the Corrosion Performance of Ni-Cr-Mo Alloys,” Paper 93417 in the

13



136. J. C. Farmer, J. J. Haslam, S. D. Day, T. Lian, R. B. Rebak, N. Yang, and L. Aprigliano

“Corrosion Resistance of Iron Based Amorphous Metal Coatings,” Paper 93835 in the



137. N. S. Meck, P. Crook and R. B. Rebak, “Electrochemical Behaviour of Nickel Alloys in

HCl Solutions Containing Oxidizing Impurities,” Stainless Steel World, May 2006, pp.

20-31

138. J. H. Payer, S. A. Carroll, G. E. Gdowski and R. B. Rebak, “A Framework for the

Analysis of Localized Corrosion at the Proposed Yucca Mountain Repository,” in


International High-Level Radioactive Waste Management

Conference, Las Vegas, NV April 30 to May 04, 2006, pp. 470-477 (American Nuclear

Society, La Grange Park, IL)

139. T. Lian, T. Yashiki, T. Nakanishi, T. Nakayama and R. B. Rebak, “Comparative

Localized Corrosion Behavior Between High and Low Palladium Titanium Alloys,” in


International High-Level Radioactive Waste Management

Conference, Las Vegas, NV April 30 to May 04, 2006, pp. 890-899 (American Nuclear

Society, La Grange Park, IL)

140. R. B. Rebak and J. H. Payer, “Passive Corrosion Behavior of Alloy 22,” in proceedings

of the 11th

International High-Level Radioactive Waste Management Conference, Las

Vegas, NV April 30 to May 04, 2006, pp. 493-499 (American Nuclear Society, La

Grange Park, IL)

141. R. B. Rebak, “Industrial Experience on the Caustic Cracking of Stainless Steels and

Nickel Alloys – A Review,” Paper 06501, Corrosion/2006, NACE International, March

12-16, 2006, San Diego, CA (NACE International, Houston, TX)

142. F. Hua, G. M. Gordon, K. G. Mon and R. B. Rebak, “Degradation Modes of Alloy 22 in

Yucca Mountain Repository Conditions,” Paper 06619, Corrosion/2006, NACE

International, March 12-16, 2006, San Diego, CA (NACE International, Houston, TX)

143. R. H. Jones, D. R. Baer, C. F. Windisch Jr. and R. B. Rebak, “Corrosion Enhanced

Enrichment of Sulfur and Implications for Alloy 22,” Paper 06621, Corrosion/2006,

NACE International, March 12-16, 2006, San Diego, CA (NACE International, Houston,

TX)

144. K. J. Evans, M. L. Stuart, R. A. Etien, G. A. Hust, J. C. Estill and R. B. Rebak, “Long-

Term Corrosion Potential and Corrosion Rate of Creviced Alloy 22 in Chloride plus

Nitrate Brines,” Paper 06623, Corrosion/2006, NACE International, March 12-16, 2006,

San Diego, CA (NACE International, Houston, TX)

145. R. B. Rebak, R. A. Etien and G. O. Ilevbare, “Influence of Black Annealing Oxide Scale

on the Anodic Behavior of Alloy 22,” Paper 06624, Corrosion/2006, NACE


14

146. R. M. Carranza, M. A. Rodríguez and R. B. Rebak, “Inhibition of Chloride Induced

Crevice Corrosion in Alloy 22 by Fluoride Ions,” Paper 06626, Corrosion/2006, NACE


147. R. M. Carranza, C. M. Giordano, M. A. Rodríguez and R. B. Rebak, “Corrosion

Behavior of Alloy 22 in Chloride Solutions Containing Organic Acids,” Paper 06627,

Corrosion/2006, NACE International, March 12-16, 2006, San Diego, CA (NACE

International, Houston, TX)

148. R. B. Rebak, “Aqueous Corrosion Properties of Nickel Alloys” and “Environmental

Cracking of Nickel Alloys” in Metals Handbook, Volume 13B “Corrosion: Materials, pp.

231-238 and pp. 238-240 (ASM International, 2005: Metals Park, OH)

149. R. M. Carranza, R. B. Rebak and M. A. Rodríguez, “Effecto Inhibidor del Fluoruro

Sobre la Corrosión en Rendijas de la Aleación C-22 Inducida por Cloruros,” in

proceedings of the Congreso Binacional SAM / CONAMET 2005, 18-21 October 2005,

Mar del Plata, Argentina

150. R. M. Carranza, M. A. Rodríguez and R. B. Rebak, “Passivity of Alloy 22 in Chloride

and Fluoride Containing Environments,” in Proceedings of the 16th

International

Corrosion Congress, Beijing, China, September 19-24 2005, Paper 06-02 (Chinese

Society for Corrosion and Protection, 2005: Beijing, China)

151. F. Hua, P. Pasupathi, N. Brown, K. G. Mon, G. M. Gordon, D. W. Shoesmith, and

R. B. Rebak, “Some Materials Degradation Issues in the US High-Level Nuclear Waste

Repository Study,” in Proceedings of the 16th

International Corrosion Congress, Beijing,

China, September 19-24 2005, Paper 06-01 (Chinese Society for Corrosion and

Protection, 2005: Beijing, China)

152. R. B. Rebak,“Environmentally Assisted Cracking of Commercial Ni-Cr-Mo Alloys – A

Review,” Power Plant Chemistry, Vol. 7, pp. 623-631 (2005)

153. K. G. Mon, G. M. Gordon, and R. B. Rebak, “Stifling of Crevice Corrosion in Alloy 22,”

in Proceedings of the 12th

International Conference on Environmental Degradation of

Materials in Nuclear Power Systems – Water Reactors, pp. 1431-1438, Salt Lake City,

UT 14-18 August 2005 (TMS, 2005: Warrendale, PA)

154. D. V. Fix, J. C. Estill, and R. B. Rebak, “Effect of Small Variation in the Composition of

Plates and Weld Filler Wires on the General Corrosion Rate of Ni-Cr-Mo Alloys,” paper

PVP2005-71173 in Proceedings of the 2005 ASME Pressure Vessels and Piping Division

Conference, July 17-21 2005, Denver, CO, Vol. 7, pp. 483-492 (American Society of

Mechanical Engineers, New York, NY)

155. K. G. Mon, A. Yilmaz, P. Pasupathi, and R. B. Rebak, “Stifling of Crevice Corrosion in

Alloy 22 During Constant Potential Tests,” paper PVP2005-71174 in Proceedings of the

2005 ASME Pressure Vessels and Piping Division Conference, July 17-21 2005, Denver,

CO, Vol. 7, pp. 493-502 (American Society of Mechanical Engineers, 2005: New York,

NY)

156. A. Yilmaz, D. V. Fix, J. C. Estill and R. B. Rebak, “Correlation Between Two Types of

Surface Stress Mitigation and the Resistance to Corrosion of Alloy 22,” paper PVP2005-

71175 in Proceedings of the 2005 ASME Pressure Vessels and Piping Division

15


Mechanical Engineers, 2005: New York, NY)

157. K. J. King, J. C. Estill and R. B. Rebak, “Anodic Behavior of Specimens Prepared from

a Full-Diameter Alloy 22 Fabricated Container for Nuclear Waste,” paper PVP2005-

71176 in Proceedings of the 2005 ASME Pressure Vessels and Piping Division


Mechanical Engineers, 2005: New York, NY)

158. R. B. Rebak, “Effect of processing on materials properties for nuclear waste disposition:

Foreword,” Metallurgical and Materials Transactions A, Vol. 36A, No. 5, p. 1073 (2005)

159. A. Yilmaz, D. Chandra and R. B. Rebak, “Corrosion Behavior of Carbon Steel Rock

Bolt in Simulated Yucca Mountain Ground Water,” Metallurgical and Materials

Transactions A, Vol. 36A, No. 5, pp. 1097-1105 (2005)

160. M. A. Rodriguez, R. M. Carranza and R. B. Rebak, “Influence of Halide Ions and Alloy

Microstructure on the Passive and Localized Corrosion Behavior of Alloy 22,”

Metallurgical and Materials Transactions A, Vol. 36A, No. 5, pp. 1179-1185 (2005)

161. J. C. Estill, G. A. Hust, K. J. King and R. B. Rebak, “Corrosion Rate of Alloy 22 as a

Function of Immersion Time,” TMS Letters, Vol. 2, pp. 13-14 (2005)

162. N. S. Meck, P. Crook and R. B. Rebak, “Electrochemical Behavior of Nickel Alloys in

HCl Solutions Containing Oxidizing Impurities,” Paper 05334, Corrosion/2005, NACE

International, April 03-07, 2005, Houston, TX (NACE International, Houston, TX)

163. M. A. Rodriguez, R. M. Carranza, S. D. Day and R. B. Rebak, “Crevice Corrosion

Susceptibility of Alloy 22 in Fluoride and Chloride Containing Environments,” Paper

05599, Corrosion/2005, NACE International, April 03-07, 2005, Houston, TX (NACE

International, Houston, TX)

164. D. V. Fix, A. Yilmaz, L. L. Wong, J. C. Estill and R. B. Rebak, “Effect of Surface Stress

Mitigation on the Corrosion Behavior of Alloy 22,” Paper 05606, Corrosion/2005, NACE

International, April 03-07, 2005, Houston, TX (NACE International, Houston, TX)

165. K. J. King, J. C. Estill, G. A. Hust, M. L. Stuart and R. B. Rebak, “Evolution of the

Corrosion Potential and the Corrosion Rate for Alloy 22 in Chloride Plus Nitrate Brines,”

Paper 05607, Corrosion/2005, NACE International, April 03-07, 2005, Houston, TX

(NACE International, Houston, TX)

166. R. B. Rebak, “Factors Affecting the Crevice Corrosion Susceptibility of Alloy 22,”

Paper 05610, Corrosion/2005, NACE International, April 03-07, 2005, Houston, TX

(NACE International, Houston, TX)

167. K. J. Evans, A. Yilmaz, S. Daniel Day, L. L. Wong, J. C. Estill, and R. B. Rebak, “Using

Electrochemical Methods to Determine Alloy 22’s Crevice Corrosion Repassivation

Potential,” Journal of Metals, Vol. 57, No. 1, pp. 56-61 (2005)

168. N. S. Meck, P. Crook, and R. B. Rebak, “Effects of Oxidizing Impurities on the

Corrosion Performance of Nickel Alloys in Hydrochloric Acid Solutions,” Stainless-Steel

World America - 2004 Conference Proceedings, 20-22 October 2004, Houston, TX

16

169. S. D. Day, M. T. Whalen, K. J. King, G. A. Hust, L. L. Wong, J. C. Estill, and

R. B. Rebak, “Corrosion Behavior of Alloy 22 in Oxalic Acid and Sodium Chloride

Solutions,” Corrosion, Vol. 60, No. 9, pp. 804-814 (2004)

170. R. B. Rebak, “Environmentally Assisted Cracking of Nickel Alloys – A Review,”

presented at the Second International Conference on Environment-Induced Cracking of

Metals (EICM-2), 19-23 September 2004, Banff, Alberta, Canada (Elsevier, published

November 2007)

171. D. V. Fix, J. C. Estill, L. L. Wong, and R. B. Rebak, “General and Localized Corrosion

of Austenitic and Borated Stainless Steels in Simulated Concentrated Ground Waters,” in

proceedings of the 2004 ASME Pressure Vessels and Piping Division Conference, July

25-29 2004, San Diego, CA, Vol. 483, pp. 121-130 (American Society of Mechanical

Engineers, 2004: New York, NY)

172. P. Crook and R. B. Rebak, “Influence of the Environment on the General Corrosion Rate

of Alloy 22 (N06022),” in proceedings of the 2004 ASME Pressure Vessels and Piping

Division Conference, July 25-29 2004, San Diego, CA, Vol. 483, pp. 131-136 (American

Society of Mechanical Engineers, 2004: New York, NY)

173. K. J. Evans, L. L. Wong, and R. B. Rebak, “Determination of the Crevice Repassivation

Potential of Alloy 22 by a Potentiodynamic-Galvanostatic-Potentiostatic Method,” in

Proceedings of the 2004 ASME Pressure Vessels and Piping Division Conference, July

25-29 2004, San Diego, CA, Vol. 483, pp. 137-149 (American Society of Mechanical

Engineers, 2004: New York, NY)

174. N. S. Meck, P. Crook, D. L. Klarstrom, and R. B. Rebak, “Effect of Ferric Ions on the

Corrosion Performance of Nickel Alloys in Hydrochloric Acid Solutions,” Paper 04430,

Corrosion/2004, NACE International, March 28 – April 1, 2004, New Orleans, LA


175. I. G. Wright, B. A. Pint, Y. Zhang, R. A. Bishop, J. C. Farmer, A. Jankowski, and

R. B. Rebak, “Preliminary High-Temperature Oxidation Data in Steam-CO2 in Support

of the ZEST Process,“ Paper 04531, Corrosion/2004, NACE International, March 28 –

April 1, 2004, New Orleans, LA (NACE International, 2004: Houston, TX)

176. K. J. King, L. L. Wong, J. C. Estill and R. B. Rebak, “Slow Strain Rate Testing of Alloy

22 in Simulated Concentrated Ground Waters,” Paper 04548, Corrosion/2004, NACE

International, March 28 – April 1, 2004, New Orleans, LA (NACE International, 2004:

Houston, TX)

177. D. V. Fix, J. C. Estill, G. A. Hust, L. L. Wong and R. B. Rebak, “Environmentally

Assisted Cracking Behavior of Nickel Alloys in Simulated Acidic and Alkaline Ground

Waters Using U-Bend Specimens,” Paper 04549, Corrosion/2004, NACE International,

March 28 – April 1, 2004, New Orleans, LA (NACE International, 2004: Houston, TX)

178. D. V. Fix, J. C. Estill, L. L. Wong and R. B. Rebak, “Susceptibility of Welded and Non-

Welded Titanium Alloys to Environmentally Assisted Cracking in Simulated

Concentrated Ground Waters,” Paper 04551, Corrosion/2004, NACE International,

March 28 – April 1, 2004, New Orleans, LA (NACE International, 2004: Houston, TX)

17

179. J. H. Lee, T. Summers and R. B. Rebak, “A Performance Assessment Model for

Localized Corrosion Susceptibility of Alloy 22 in Chloride Containing Brines for High-

level Nuclear Waste Disposal Container,” Paper 04692, Corrosion/2004, NACE

International, March 28 – April 1, 2004, New Orleans, LA (NACE International, 2004:

Houston, TX)

180. M. A. Rodríguez, R. M. Carranza and R. B. Rebak, “Effect of Fluoride Ions on the

Anodic Behavior of Mill Annealed and Thermally Aged Alloy 22,” Paper 04700,



181. L. L. Wong, T. Lian, D. V. Fix, M. Sutton and R. B. Rebak, “Surface Analysis of Alloy

22 Coupons Exposed for Five Years to Concentrated Ground Waters,” Paper 04701,



182. F. Wong, C. Punshon, J. Dorsch, P. Fielding, D. Richard, N. Yang, M. Hill, A. DeWald,

R. B. Rebak, S. Day, L. Wong, S. Torres, M. McGregor. L. Hackel, H.-L. Chen and J.

Rankin, “Reduced Pressure Electron Beam Welding Evaluation Activities on a Ni-Cr-Mo

Alloy for Nuclear Waste Package,” in proceedings of the Global 2003 Conference:

Atoms for Prosperity: Updating Eisenhower’s Global Vision for Nuclear Energy, New

Orleans, LA, 16-20 November 2003, pp. 242-250 (American Nuclear Society, 2003: La

Grange Park, IL)

183. R. B. Rebak, “Effects of Metallurgical Variables on the Corrosion of High-Nickel

Alloys” in Metals Handbook, Volume 13A “Corrosion: Fundamentals, Testing and

Protection, pp. 279-286 (ASM International, 2003: Metals Park, OH)

184. R. B. Rebak and J. C. Estill, “Review of Corrosion Modes for Alloy 22 Regarding

Lifetime Expectancy of Nuclear Waste Containers” in Scientific Basis for Nuclear Waste

Management XXVI, Vol. 757, pp. 713-721 (Materials Research Society, 2003:

Warrendale, PA)

185. L. L. Wong, D. V. Fix, J. C. Estill, R. D. McCright, and R. B. Rebak, “Characterization

of the Corrosion Behavior of Alloy 22 after Five Years Immersion in Multi-Ionic

Solutions” in Scientific Basis for Nuclear Waste Management XXVI, Vol. 757, pp. 735-

741 (Materials Research Society, 2003: Warrendale, PA)

186. K. J. Evans, S. D. Day, G. O. Ilevbare, M. T. Whalen, K. J. King, G. A. Hust, L. L.

Wong, J. C. Estill, and R. B. Rebak, “Anodic Behavior of Alloy 22 in Calcium Chloride

and in Calcium Chloride plus Calcium Nitrate Brines,” American Society of Mechanical

Engineers, Pressure Vessels and Piping Division, PVP-Vol. 467, pp. 55-62 (New York,

NY: ASME, 2003)

187. L. L. Wong, D. V. Fix, J. C. Estill, and R. B. Rebak, “Corrosion Characteristics of

Titanium Alloys in Multi-ionic Environments,” American Society of Mechanical

Engineers, Pressure Vessels and Piping Division, PVP-Vol. 467, pp. 63-71 (New York,

NY: ASME, 2003)

188. N. S. Meck, P. Crook, S. D. Day, and R. B. Rebak, “Localized Corrosion Susceptibility

of Nickel Alloys in Halide Containing Environments,” Paper 03682 (Houston, TX:

NACE International, 2003)

18

189. J. C. Estill, G. A. Hust, and R. B. Rebak, “Long Term Corrosion Potential Behavior of

Alloy 22 in Yucca Mountain Relevant Environments,” Paper 03688 (Houston, TX:

NACE International, 2003)

190. T. Lian, J. C. Estill, G. A. Hust, and R. B. Rebak, “Passive and Transpassive Dissolution

of Alloy 22 in Simulated Repository Environments,” Paper 03694 (Houston, TX: NACE

International, 2003)

191. K. J. King, J. C. Estill, D. V. Fix, G. A. Hust, and R. B. Rebak, “Influence of

Environmental Variables on the Susceptibility of Alloy 22 to Environmentally Assisted

Cracking,” Paper 03542 (Houston, TX: NACE International, 2003)

192. T. Lian, J. C. Estill, G. A. Hust, D. V. Fix, and R. B. Rebak, “Passive Corrosion

Behavior of Alloy 22 in Multi-Ionic Aqueous Environments,” American Society of

Mechanical Engineers, Pressure Vessels and Piping Division, PVP-Vol. 449, pp. 67-74

(New York, NY: ASME, 2002)

193. K. J. King, J. C. Estill and R. B. Rebak, “Characterization of the Resistance of Alloy 22

to Stress Corrosion Cracking,” American Society of Mechanical Engineers, Pressure

Vessels and Piping Division, PVP-Vol. 449, pp. 103-109 (New York, NY: ASME, 2002)

194. P. Crook and R. B. Rebak, “Mechanical Properties and Corrosion Characteristics of

Thermally Aged Alloy 22,” American Society of Mechanical Engineers, Pressure Vessels

and Piping Division, PVP-Vol. 449, pp. 111-117 (New York, NY: ASME, 2002)

195. K. J. Evans and R. B. Rebak, “Passivity of Alloy 22 in Concentrated Electrolytes. Effect

of Temperature and Solution Composition,” PV2002-13, pp. 344-354 (The

Electrochemical Society, 2002: Pennington, NJ)

196. N. S. Meck, P. Crook and R. B. Rebak, “Susceptibility of Nickel and Cobalt Alloys to

Localized Corrosion in Fluoride and Iodide Solutions. Comparative Behavior to Chloride

and Bromide Solutions,” PV2002-13, pp. 355-368 (The Electrochemical Society, 2002:

Pennington, NJ)

197. R. B. Rebak, T. S. Edgecumbe Summers, T. Lian, R. M. Carranza, J. R. Dillman, T.

Corbin and P. Crook, “Effect of Thermal Aging on the Corrosion Behavior of Wrought

and Welded Alloy 22,” Paper 02542, Corrosion/02, NACE International, April 7-12,

2002, Denver CO

198. J. C. Estill, K. J. King, D. V. Fix, D. G. Spurlock, G. A. Hust, S. R. Gordon, R. D.

McCright, G. M. Gordon, and R. B. Rebak, “Susceptibility of Alloy 22 to

Environmentally Assisted Cracking in Yucca Mountain Relevant Environments,” Paper

02535, Corrosion/02, NACE International, April 7-12, 2002, Denver CO

199. T. S. E. Summers, R. B. Rebak, T. A. Palmer and P. Crook, “Influence of Thermal

Aging on the Mechanical and Corrosion Properties of GTAW Welds of Alloy 22,” Paper

JJ1.5, Scientific Basis for Nuclear Waste Management XXV, MRS Meeting Boston,

November 26-30, 2001, Vol. 713, pp. 45-52 (Materials Research Society, 2002:

Warrendale, PA)

200. R. B. Rebak, P. Crook, J. R. Dillman, and C. V. V. Shawber, “Corrosion Behavior of

Nickel Alloys in Wet Hydrofluoric Acid,” Materials and Corrosion (Werkstoffe und

Korrosion), 52, No. 4, 289-297 (2001)

19

201. R. B. Rebak, “Corrosion of Non-ferrous Alloys. I Nickel-, Cobalt-, Copper-, Zirconium-

and Titanium Based Alloys,” Chapter 2 in Volume II of “Corrosion and Environmental

Degradation” edited by M. Schütze. Volume 19 of the series “Materials Science and

Technology - A Comprehensive Treatment” Edited by R. W. Cahn, P. Haasen and E. J.

Kramer (Wiley-VCH, Germany, 2000): pp. 69-111

202. R. B. Rebak, “Environmentally Assisted Cracking in the Chemical Process Industry.

Stress Corrosion Cracking of Iron, Nickel and Cobalt Based Alloys in Chloride and Wet

HF Services,” in Environmentally Assisted Cracking: Predictive Methods for Risk

Assessment and Evaluation of Materials, Equipment, and Structures, ASTM STP 1401, R.

D. Kane, Ed., American Society for Testing and Materials, West Conshohocken, PA, pp.

289-300 (2000)

203. R. B. Rebak T. S. E. Summers and R. R. Seeley, “Influence of Thermal Aging on the

Mechanical and Corrosion Properties of C-22 Alloy Welds,” in Materials Issues in

Nuclear Waste Management, 2000 TMS Fall Meeting, October 8-12, St. Louis, Missouri

(TMS, 2000: Warrendale, PA)

204. R. B. Rebak and D. A. Kingseed, “Performance of Conductor Rolls Alloys in

Electrogalvanizing Plants,” presented at Workshop on Continuous Steel Strip Plating,

Merrilville, Indiana, May 9-10, 2000. Published in the proceedings of the conference

205. R. B. Rebak, P. Crook, and R. Baden, “Corrosion-Resistant Nickel Alloys,” ACHEMA

2000, Frankfurt, Germany, May 2000

206. R. B. Rebak, N. E. Koon, J. R. Dillman, P. Crook, and T. S. E. Summers, “Influence of

Aging on Microstructure, Mechanical Properties and Corrosion Resistance of C-22

Alloy,” Paper 00181, Corrosion/2000, Orlando, Florida, March 26-31, 2000

207. R. B. Rebak and P. Crook, “Influence of Alloying Elements, Temperature and

Electrolyte Composition on the Corrosion Behavior of Nickel Based Alloys,” Paper

00499, Corrosion/2000, Orlando, Florida, March 26-31 2000

208. R. B. Rebak, D. A. Kingseed and P. Crook, “Pitting Nickel Against Corrosion,”

Chemical Processing, Vol. 63, February, pp. 49-54 (2000)

209. R. B. Rebak and P. Crook, “Nickel Alloys for Corrosive Environments,” Advanced

Materials and Processes, Vol. 157, February, pp. 37-42 (2000)

210. R. B. Rebak, T. S. E. Summers, and R. M. Carranza, “Mechanical Properties,

Microstructure and Corrosion Performance of C-22 Alloy Aged at 260°C to 800°C,”

Paper QQ14.4, Symposium on Scientific Basis for Nuclear Waste Management XXIII,

1999 MRS Fall meeting, Boston, Massachusetts, November 29 - December 3, 1999, Vol.

608, pp. 109-114 (Materials Research Society, Warrendale, PA, 2000)

211. R. B. Rebak, N. E. Koon, and P. Crook, “Localized Corrosion Behavior of Nickel and

Cobalt Based Alloys in Chloride and Bromide Solutions,” in proceedings of the

International Symposium in honor of Professor Norio Sato: Passivity and Localized

Corrosion, Honolulu, Hawaii, October 17-22, 1999, Vol. 99-27, pp. 473-482 (The

Electrochemical Society, Pennington, NJ, 1999)

212. R. B. Rebak, N. E. Koon, and P. Crook, “Effect of High Temperature Ageing on the

Electrochemical Behaviour of C-22 Alloy,” presented at the 50th International Society of

20

Electrochemistry Meeting, Pavia, Italy, September 5-10, 1999 published by the European

Federation of Corrosion, Vol. 28, Paper 14 (The Institute of Materials, London, 2000):

pp. 245-255

213. T. S. Edgecumbe Summers, T. Shen, and R. B. Rebak, “Prediction of the Lifetime

Integrity of a Nuclear Waste Container Material Based on Thermal Stability Studies,” in

International Conference on Ageing Studies and Lifetime Extension of Materials, St.

Catherine’s College, Oxford, UK July 12-14 1999, pp. 507-513 (Kluwer Academic /

Plenum Publishers, 2001: New York, NY)

214. L. D. Paul, P. Crook, and R. B. Rebak, “Corrosion Resistant Material Options for

Environmental Equipment,” in proceedings of the Incineration and Thermal Treatment

Technologies Conference, Orlando, Florida, May 11-13, 1999

215. R. B. Rebak and S. K. Srivastava, “Corrosion Performance of a Nickel-Molybdenum-

Chromium Alloy: Effects of Aging, Alloying Elements and Electrolyte Composition,”

Corrosion, Vol. 55, pp. 412-421 (1999)

216. R. B. Rebak, “Corrosion Rate of Nickel Based Alloys Measured by Electrochemical

Techniques and Immersion Tests. Effect of Temperature, Alloying Elements and

Electrolyte Composition,” Paper 99219 in Corrosion/99, San Antonio, Texas, April 25-

30, 1999

217. R. B. Rebak, T. S. Edgecumbe Summers, M. A. Wall, M. Kumar and S. J. Matthews,

“Phase Stability and Mechanical Properties of C-22 Alloy Aged in the Temperature

Range 590°C to 760°C for 16,000 h,” Paper QQ9.71 in the Symposium on Scientific

Basis for Nuclear Waste Management XXII, Fall Meeting of the Materials Research

Society, Boston, Massachusetts, November 30 - December 4, 1998, Vol. 556 (Materials

Research Society, Warrendale, PA, 1999): pp. 919-926

218. R. B. Rebak and P. Crook, “Improved Pitting and Crevice Corrosion Resistance of

Nickel and Cobalt Based Alloys,” in the symposium on “Critical Factors in Localized

Corrosion III” at the 194th Electrochemical Society Meeting, Boston, Massachusetts,

November 1-6, 1998, Volume 98-17 (The Electrochemical Society, Pennington, NJ,

1999): pp. 289-302

219. R. B. Rebak, “Comparison Between Electrochemical Methods and Immersion Tests for

Measuring the Corrosion Rate of Three Nickel Based Alloys. Effect of Temperature,

Alloying Elements and Electrolyte Composition,” Paper S17-32 in the 3rd NACE Latin

American Region Corrosion Congress, Cancún, Mexico, August 30 - September 4, 1998

220. R. B. Rebak and N. E. Koon, “Localized Corrosion Resistance of High Nickel Alloys as

Candidate Materials for Nuclear Waste Repository. Effect of Alloy and Weldment Aging

at 427°C for up to 40,000 h,” Paper N° 98153, Corrosion '98, San Diego, California,

March 22-27, 1998 (Houston, TX: NACE International, 1998)

221. R. B. Rebak, “Materials Selection for Conductor Rolls in Electrogalvanizing Plants,” in

proceedings of the international symposium on “Zinc-Based Steel Coating Systems:

Production and Performance,” 127th Annual TMS Meeting in San Antonio, TX February

15-19, 1998, pp. 63-72 (The Minerals, Metals and Materials Society, Warrendale, PA,

1998)

21

222. R. B. Rebak, “Localized Corrosion Resistance of HASTELLOY® C-22®, C-276 and C-

4 Alloys as Candidate Materials for Nuclear Waste Repository. Effect of Alloy Aging at

427°C for up to 40,000 h.,” presented as paper N° 347 in the Joint International Meeting

of the 192nd Meeting of the Electrochemical Society (ECS) and the 48th Annual Meeting

of the International Society of Electrochemistry (ISE), August 31 - September 5, 1997 in

Paris, France, Volume 97-26 (The Electrochemical Society, Pennington, NJ, 1998): pp.

1001-1012

223. A. Barkatt, E. Labuda, D. M. Wilder, G. Cherepakhov, R. J. Burns, Z. Szklarska-

Smialowska, R. Mowad, and R. B. Rebak, “Effects of Ethanolamine, pH Change, and

Increased Hydrazine Levels on Deposit-Covered Alloy 600 and Brass Corrosion,”

Materials Performance, (September 1997): pp. 48-53

224. R. B. Rebak, L. Muchjin and Z. Szklarska-Smialowska, “Hydrogen Diffusion and

Accumulation in Automotive Fasteners,” Corrosion, 53 (1997): pp. 481-488

225. R. B. Rebak, “Laboratory Testing to Evaluate the Corrosion Performance of Conducting

Roll Materials in the Electroplating Industry,” Paper 97264, Corrosion '97, New Orleans,

Louisiana, March 9-14, 1997 (Houston, TX: NACE International, 1997)

226. A. Barkatt, E. Labuda, D. M. Wilder, M. Gmurczyk, Z. Szklarska-Smialowska, R.

Mowad, and R. B. Rebak, “Effects of Ethanolamine as an Additive in the Secondary

Water at Indian Point 2,” Paper 97117, Corrosion '97, New Orleans, Louisiana, March 9-

14, 1997 (Houston, TX: NACE International, 1997)

227. R. B. Rebak, “Application of Co-Cr-Ni and Ni-Cr-Mo Alloys in the Electrogalvanizing

Industry,” in Proceedings of the Second Latin-American Corrosion Congress, Rio de

Janeiro, Brazil, September 9-13 1996. Paper LA 96074

228. A. Barkatt, E. Labuda, D. M. Wilder, M. Gmurczyk, Z. Szklarska-Smialowska, R.

Mowad and R. B. Rebak, “Effects of Additives and pH of Secondary Water on Deposits

in the Steam Generators and on Brass Corrosion at Indian Point 2,” EPRI Sludge

Management Workshop in Myrtle Beach, South Carolina, August 19-21, 1996

229. R. B. Rebak and Z. Szklarska-Smialowska, “The Mechanism of Stress Corrosion

Cracking of Alloy 600 in High Purity Water,” Corrosion Science, 38 (1996): pp. 971-988

230. R. B. Rebak, Z. Xia, R. Safruddin and Z. Szklarska-Smialowska, “Effect of Solution

Composition and Electrochemical Potential on Stress Corrosion Cracking of X-52

Pipeline Steel,” Corrosion, 52 (1996): pp. 396-405

231. R. B. Rebak and Z. Szklarska-Smialowska, “Stress Corrosion Cracking of Alloy 600 in

High Temperature Aqueous Solutions: Influencing Factors, Mechanisms and Models,” in

Control of Corrosion on the Secondary Side of Steam Generators, Proceedings of a

Conference jointly sponsored by The Electric Power Research Institute and Argonne

National Laboratory, Airlie, Virginia, October 9-13, 1995 (Houston, TX: NACE

International, 1996): pp. 223-257

232. R. B. Rebak, Z. Xia and Z. Szklarska-Smialowska, “Effect of Temperature and Cold

Work on the Crack Growth Rate of Alloy 600 in Primary Water,” Corrosion, 51 (1995):

pp. 689-697

22

233. R. B. Rebak and Z. Szklarska-Smialowska, “About the Mechanism of Stress Corrosion

Cracking of Alloy 600 in High Temperature Water,” in Proceedings of the Seventh

International Symposium on Environmental Degradation of Materials in Nuclear Power

Systems - Water Reactors, Breckenridge, CO, August 7-10 1995 (Houston, TX: NACE

International, 1995): pp. 855-865

234. R. B. Rebak and Z. Szklarska-Smialowska, “Prediction of Crack Growth Rate in Service

from Accelerated Tests in Laboratory for Steam Generator Alloy 600 Tubing,” in

Proceedings of the International Symposium on Plant Aging and Life Prediction of

Corrodible Structures, Sapporo, Japan, May 15-18 1995, Paper A II 15 (Houston, TX:

NACE International, 1997): pp. 257-264

235. R. B. Rebak and Z. Szklarska-Smialowska, “Effect of Specimen Thickness on Cracking

Susceptibility of Alloy 600 in High Temperature Water,” Corrosion, 51 (1995): pp. 376-

379

236. R. B. Rebak, Z. Xia, R. Safruddin and Z. Szklarska-Smialowska, “Electrochemical

Processes Controlling SCC of Underground Pipelines,” Paper 184, Corrosion '95,

Orlando, Florida, March 26-31, 1995 (Houston, TX: NACE International, 1995): 17

pages

237. R. B. Rebak and Z. Szklarska-Smialowska, “Influence of Stress Intensity and Loading

Mode On Intergranular Stress Corrosion Cracking of Alloy 600 in Primary Waters of

Pressurized Water Reactors,” Corrosion, 50 (1994): pp. 378-393

238. R. B. Rebak, Z. Szklarska-Smialowska and Z. Xia, “Stress Corrosion Cracking of X-52

Carbon Steel in Dilute Aqueous Solutions,” Corrosion, 50 (1994): pp. 334-338

239. R. B. Rebak, Z. Szklarska-Smialowska, Z. Xia, and P. Skulte, “Susceptibility of Low

Alloy Carbon Steel to Pitting and Stress Corrosion Cracking in Steam Generator

Conditions,” Corrosion, 50 (1994): pp. 279-289

240. R. B. Rebak, Z. Xia, and Z. Szklarska-Smialowska, “Effects of Carbides on

Susceptibility of Alloy 600 to Stress Corrosion Cracking in High-Temperature Water,”

Corrosion, 49 (1993): pp. 867-876

241. R. B. Rebak, A. R. McIlree, and Z. Szklarska-Smialowska, “Effects of pH and Stress

Intensity on Crack Growth Rate in Alloy 600 in Lithiated + Borated Water at High

Temperatures,” in Proceedings of the Fifth International Symposium on Environmental

Degradation of Materials in Nuclear Power Systems - Water Reactors, Monterey, CA,

August 25-29, 1991 (La Grange Park, IL: American Nuclear Society, 1992): pp. 511-517

242. R. B. Rebak and Z. Szklarska-Smialowska, “Effect of Partial Pressure of Hydrogen on

IGSCC of Alloy 600 in PWR Primary Water,” Corrosion, 47 (1991): pp. 754-757

243. R. B. Rebak, Z. Szklarska-Smialowska and A. R. McIlree, “Relationship of Stress

Intensity to Crack Growth Rate of Alloy 600 in Primary Water,” in Proceedings of the

International Symposium FONTEVRAUD II - Volume 1, Royal Abbey of Fontevraud,

France, September 10-14, 1990 (Société Française d'Energie Nucléaire, 1990): pp. 258-

267

23

244. R. B. Rebak and J. R. Galvele, “Stress Corrosion Cracking of a-Brass in Phosphate,

Triphosphate and Pyrophosphate Solutions,” Corrosion Science, 29 (1989): pp. 1003-

1018

245. R. B. Rebak, R. M. Carranza and J. R. Galvele, “The Stress Corrosion Cracking

Mechanism of a-Brass in NaNO2 Solutions,” Corrosion Science, 28 (1988): pp. 1089-

1106

246. R. B. Rebak and J. R. Galvele, “Corrosión Bajo Tensión del Latón en Soluciones de

Fosfatos,” in proceedings of the VIII Reunión Latinoamericana de Electroquímica,

October 31 - November 4 1988, Huerta Grande, Córdoba, Argentina (1988): pp. 543-545

247. R. B. Rebak and J. R. Galvele, “Efecto de los Iones P2O7-4

y P3O10-5

Sobre la

Susceptibilidad del Latón a Sufrir Corrosión Bajo Tensión,” in proceedings of the

Jornadas Metalúrgicas, May 11-15, 1987 (Buenos Aires, Argentina: Sociedad Argentina

de Metales, 1987): pp. 27-29

248. R. B. Rebak and J. R. Galvele, “Susceptibilidad a la Corrosión Bajo Tensión del Latón

en Soluciones de KSCN,” in proceedings of the Jornadas Metalúrgicas, May 11-15, 1987

(Buenos Aires, Argentina: Sociedad Argentina de Metales, 1987): p. 23-26

249. R. B. Rebak, R. M. Carranza, and J. R. Galvele, “Corrosión Bajo Tensión de Alfa

Latones en Soluciones de Nitrito,” in proceedings of the III Jornadas Nacionales de

Corrosión, October 22-24 1986, (Santa Fe, Argentina: Asociación Argentina de la

Corrosión, 1986): pp. 52-60

250. R. B. Rebak, R. M. Carranza and J. R. Galvele, “Influencia de la Concentración de NO2-

y del pH Sobre la Velocidad de Propagación de Fisuras en Latones,” in proceedings of

the Jornadas Metalúrgicas, May 5-7, 1986 (Buenos Aires, Argentina: Sociedad Argentina

de Metales, 1986)

24

Presentations in International Conferences/Workshops

And Invited Seminars (Abstracts or Overhead Copies Published) in descending chronological order

1. R. B. Rebak, “Advanced Steels for Accident Tolerant Fuel Cladding in Current Light

Water Reactors,” invited seminar presented at the NACE International Instituto Sabato

Student Section, Atomic Energy Commission of Argentina, Buenos Aires 25-Nov-2014

2. R. B. Rebak, “Accident Tolerant Alloys for Extreme Nuclear Applications,” presented at

the 2014 Materials Science and Technology Meeting (MS&T’14), 15 October 2014,

Pittsburgh, PA, USA

3. N. S. Zadorozne, C. M. Giordano, A. E. Ares, R. M. Carranza, and R. B. Rebak,

“Environmentally Assisted Cracking of Nickel Alloys in Aqueous Solutions Containing

Bicarbonate and Chloride,” presented at the 2014 Materials Science and Technology

Meeting (MS&T’14), 16 October 2014, Pittsburgh, PA, USA

4. P. L. Andresen and R. B. Rebak, “Environmentally Assisted Cracking Resistance of

Alloys Candidate for Accident Tolerant Cladding in Light Water Reactors,” presented at

the 2014 Materials Science and Technology Meeting (MS&T’14), 15 October 2014,

Pittsburgh, PA, USA

5. Y. J. Kim, E. J. Dolley, and R. B. Rebak, “High Temperature Water Behavior of

Advanced Steels for Accident Tolerant Fuel Cladding in Light Water Reactors,” IAEA

Technical Meeting “Accident Tolerant Fuel Concepts For Light Water Reactors” ORNL,

Oak Ridge, TN 13-16 October 2014

6. G. Sundararajan and R. B. Rebak, “Electrochemical Behaviour of Protective Coatings in

Chloride Solutions,” Paper 7590 presented at Eurocorr 2014, Pisa, Italy, 08-12 Sep-2014

7. R. B. Rebak, “Accident Tolerant Advanced Steels Cladding for Commercial Light Water

Reactors Fuel,” presented at FCRD Advanced Fuels Campaign Integration Meeting,

Energy Innovation Laboratory, INL, Idaho Falls, ID, 26-Aug2014

8. R. B. Rebak, “Electrochemical Behavior of Advanced Steels for ATF Cladding under

Simulated Normal Operation Conditions,” presented at the Electric Power Research

Institute (EPRI) Fuel Reliability Program Meeting, Baltimore MD, 15-July-2014

9. R. B. Rebak, “Electrochemical Processes Controlling Localized Corrosion of Passivating

Nickel Alloys,” invited seminar presented at The Electrochemical Society Student

Chapter at the University of Virginia, 01-Jul-2014

10. R. B. Rebak, “Ferritic Steels for Accident Tolerant Fuel Cladding in Commercial Light

Water Reactors,” invited seminar presented at Spring Symposium “Materials for Extreme

Applications,” Eastern New York Chapter of ASM International, 14-May-2014

11. R. B. Rebak, “Advanced Steels as Accident Tolerant Fuel Cladding in Commercial Light

Water Reactors,” invited seminar presented at 247th

American Chemical Society (ACS)

National Meeting, Symposium Chemistry and Materials for Energy, Dallas, TX, 16-

March-2014

25

12. R. B. Rebak, “Alloy Selection for Accident Tolerant Fuel Cladding in Commercial Light

Water Reactors,” presented at the 143rd

TMS Annual Meeting, Symposium on Materials

and Fuels for the Current and Advanced Nuclear Reactors III, San Diego, CA, 18-

February-2014

13. R. B. Rebak, “Recent Developments in Oil and Gas Production,” presented at the 143rd

TMS Annual Meeting, Symposium on Materials Aspects of Corrosion and Fouling in Oil

Refining and Exploration, San Diego, CA, 19-February-2014

14. R. B. Rebak, “Advanced Steels for Accident Tolerant Fuel Cladding in Commercial

Nuclear Reactors,” invited seminar presented at Western University, London, ON,

Canada, 26-November-2013

15. R. B. Rebak, “Corrosion Behavior of Container Alloys in Nuclear Waste Repositories,”

presented at the 2013 Materials Science and Technology Meeting (MS&T’13), Montréal,

Canada, 28-October-2013

16. N. S. Zadorozne, C. M. Giordano, A. E. Ares, R. M. Carranza, and R. B. Rebak, “Stress

Corrosion Cracking of Nickel Alloys in Bicarbonate Solutions,” presented at the 2013

Materials Science and Technology Meeting (MS&T’13), Montréal, Canada, 28-October-

2013

17. M. A. Rodriguez, C. M. Giordano, R. M. Carranza, M. Iannuzzi, and R. B. Rebak,

“Repassivation Potential for Localized Corrosion and the Onset for Stress Corrosion

Cracking,” presented at Eurocorr 2013, Estoril, Portugal, 02-September-2013

18. R. B. Rebak, “Specific uses of nickel alloys in corrosive environments,” 13th

International Congress on Science and Technology of Materials, Port Iguazú, Misiones,

Argentina, 20-23 August 2013

19. R. B. Rebak, “Ferritic Martensitic Alloys as Accident Tolerant Fuel (ATF) Cladding

Material for Light Water Reactors,” presented at FCRD Advanced Fuels Campaign

Integration Meeting, Salt Lake City, Utah, 27-Aug2014

20. R. B. Rebak, “GE Experience in LWR Coating Research,” presented at Fuel Cycle

Research and Development Advanced Fuels Campaign Cladding-Coating Operational

Meeting, Oak Ridge National Laboratory, Oak Ridge, TN, 12-13 February-2013

21. R. B. Rebak, “Environmental Cracking of Chromium Containing Alloys in High

Temperature Water,” presented at the 2012 Materials Science and Technology Meeting

(MS&T’12), 07-11 October 2012, Pittsburgh, PA, USA

22. N. S. Zadorozne, C. M. Giordano, R. M. Carranza, A. E. Ares, and R. B. Rebak,

“Environmental Cracking of Nickel Alloys in Bicarbonate and Chloride Solutions,”

presented at the 2012 Materials Science and Technology Meeting (MS&T’12), 07-11

October 2012, Pittsburgh, PA, USA


Generation and Nuclear Waste Disposal,” presented at the 2012 Materials Science and

Technology Meeting (MS&T’12), 07-11 October 2012, Pittsburgh, PA, USA

26


Generation and Nuclear Waste Disposal,” presented at the Eurocorr 2012, Istanbul,

Turkey, 09-13-September-2012

25. R. B. Rebak, “Fallout from Fukushima,” invited speaker to the 224X Corrosion in

Nuclear Systems committee meeting during Corrosion/2012, 11-15 March 2012 in Salt

Lake City - UT (NACE International, 2012: Houston, TX)

26. P. L. Andresen, T. B. Jurewicz and R. B. Rebak, “Environmentally Assisted Cracking

Resistance of Ferritic Chromium Steels in High Temperature Water,” presented at the

symposium “Materials Science Challenges for Nuclear Applications” during

MS&T’2011 Conference and Exhibition in Columbus, OH, 16-20 October 2011.

27. M. A. Rodriguez, R. M. Carranza, and R. B. Rebak, “Ground Water Inhibitors of

Localized Corrosion in Passivating Alloys” presented at the symposium “Materials for

Nuclear Waste Disposal and Environmental Cleanup” during MS&T’2011 Conference

and Exhibition in Columbus, OH, 16-20 October 2011.

28. R. B. Rebak, “Corrosion, Materials and the Nuclear Renaissance,” presented at the

“NACE Northern Area Eastern Conference - Ottawa, Ontario, Canada 15-17 August

2011

29. P. L. Andresen and R. B. Rebak, “Stress Corrosion Cracking Behavior of Ferritic and

Austenitic Stainless Steels in High Temperature Water” presented at the symposium

“Materials for the Nuclear Renaissance II,” during the 2011 TMS Annual Meeting &

Exhibition, San Diego – CA, 27 February to 03 March 2011

30. R. B. Rebak, “A Materialistic Career,” presented at RPI Material Advantage’s Career

Night, Rensselaer Polytechnic Institute, Troy, NY 07-February-2011.

31. R. B. Rebak, “Engineering Materials Selection for Nuclear Waste Repositories in the

USA and in the World,” invited presentation at the Graduate Seminar, Alfred University,

Alfred - NY, 02 December 2010

32. P. H. Chou and R. B. Rebak, “Electrochemical and Stress Corrosion Cracking Behavior

of Stainless Steels Containing Silicon,” presented at the International Cooperative Group

on Environmentally Assisted Cracking of Water Reactor Materials (ICG-EAC), Haevichi

Hotel on Jeju Island in the Republic of Korea, 11-16 April 2010

33. R. B. Rebak, “Is there a Nuclear Renaissance?,” invited speaker to the 224X Corrosion

in Nuclear Systems committee meeting during Corrosion/2010, 11-18 March 2010 in San

Antonio, TX (NACE International, 2010: Houston, TX)

34. R. B. Rebak, “Materials Selection for Nuclear Waste Repositories Worldwide,” invited

presentation to the Northeastern New York Section of the American Nuclear Society at

the Rensselaer Polytechnic Institute (RPI) – Linac (Linear Accelerator), Troy – NY, 03

March 2010

35. R. B. Rebak, “Comparative Plant Performance of Stabilized and Non-Stabilized

Austenitic Stainless Steels,” presented at the symposium Mechanical Performance for

Current and Next-Generation Nuclear Reactors during the 2010 TMS Annual Meeting &

Exhibition, Seattle – WA, 14-18 February 2010

27

36. R. B. Rebak, “Environmental Degradation of Materials in Light Water Reactors – Stress

Corrosion Cracking of Nickel Based Alloys,” invited plenary speaker at the 9th

International Congress of Materials organized by the Sociedad Argentina de Materiales

(SAM) and the Sociedad Chilena de Materiales (SOCHIM), 19-23 October 2009, Buenos

Aires, Argentina

37. R. B. Rebak, “Corrosion Testing in the Nuclear Power Industry,” plenary invited speaker

at the 5th

Annual Northeast NACE Corrosion Conference, 20-22 January 2009 in

Springfield, MA Section of NACE International, North-Eastern New York

38. R. B. Rebak, “Corrosion Testing of Nickel and Titanium Alloys for Nuclear Waste

Disposition,” invited speaker to the Research Topical Symposium Corrosion in Nuclear

Waste Systems during Corrosion/2008, 16-20 March 2008 in New Orleans, LA

39. D. V. Fix and R. B. Rebak, “Decommissioning the Long-Term Corrosion Test Facility

For the Yucca Mountain Project,” presented in the symposium “Degradation of Materials

for Application in Nuclear Power and Waste Management Systems” at the Materials

Science and Technology 2007 (MS&T’07) Conference and Exhibition in Detroit, MI, at

the COBO Center on 16-20 September 2007

40. T. Lian, J. A. Rard, K. J. Staggs, S. A. Carroll and R. B. Rebak, “Corrosion Studies of

Alloys 22 and 825 under Thin Brine Films at 105°C,” presented at the Research in

Progress Symposium of the NACE International Corrosion/2007 Conference and

Exposition, 11-15 March 2007, Nashville, TN

41. R. B. Rebak, L. Aprigliano, S. Day, J. Haslam and J. Farmer “Salt Fog Testing of Iron

Based Amorphous Alloys,” presented at the Materials Issues for Advanced Nuclear

Systems symposium at the 136th

Annual TMS meeting, 25 February to 01 March 2007 in

Orlando, FL

42. R. B. Rebak, “Corrosion Behavior of C-22 and other Nickel alloys,” invited speaker

Fontana Corrosion Center, The Ohio State University organized by the local student

chapter of The Electrochemical Society, Columbus, Ohio 18-October-2006

43. D. V. Fix, K. J. King, J. C. Estill and R. B. Rebak, “Corrosion Behavior of Welded

Plates of Alloy 22 with Varying Heat Composition,” TMS 2005 Annual Meeting, San

Francisco, CA 13-17 February 2005 (TMS, 2005: Warrendale, PA)

44. A. Yilmaz, D. V. Fix, J. C. Estill, L. L. Wong and R. B. Rebak, “Effect of Stress

Mitigation on the Corrosion Behavior of Alloy 22,” TMS 2005 Annual Meeting, San


45. R. B. Rebak, “Monitoring the Evolution of the Corrosion Potential and Corrosion Rate

of Alloy 22 Immersed in Various Electrolyte Solutions,” TMS 2005 Annual Meeting, San


46. A. Yilmaz, D. Chandra and R. B. Rebak, “Investigation of Portevin Le Chatelier Effect

by Electrochemical Techniques: Correlation Between Dynamic Strain Aging and Metal-

Electrolyte Interface Potentials,” MS&T’04, New Orleans, LA 26-29 September 2004

(TMS, 2004: Warrendale, PA)

28

47. K. J. Evans, L. L. Wong and R. B. Rebak, “Corrosion Testing of Nickel and Titanium

Alloys,” TMS 2004 Annual Meeting, Charlotte, NC 14-18 March 2004 (TMS, 2004:

Warrendale, PA)

48. F. M. G. Wong, R. B. Rebak, L. A. Hackel, H-L. Chen, T. F. Soules, R. M. Yamamoto,

J. E. Rankin, M. R. Hill and A. T. DeWald, “Minimizing the Potential for Stress

Corrosion Cracking in Welds of Nuclear Waste Package using Laser Peening,”

MS&T’03, Chicago, IL, November 09-12 2003 (TMS, 2003: Warrendale, PA)

49. R. B. Rebak, “Corrosion Resistant Materials for Yucca Mountain Nuclear Waste

Containers,” invited speaker at the San Francisco Bay Area Section of NACE

International, 07th

May 2002

50. R. B. Rebak, “Localized Corrosion of Waste Package Materials,” presented at the

Interim Meeting of the Peer Review Panel, US Department of Energy, Office of Civilian

Radioactive Waste Management, Las Vegas, Nevada, September 25, 2001

51. R. B. Rebak, “Nickel Alloys for Aggressive Environments,” invited speaker at the

Niagara-Frontier Section of NACE International, Monthly meeting, January 18, 2000.

52. R. B. Rebak, P. Crook and K. Ravindranath, “Nickel Based Alloys for Aggressive

Environments,” presented at the Workshop on Emerging Materials for Chemical Process

Industries, Engineers India Limited, New Delhi, India, December 6-7, 1999

53. R. B. Rebak, “Alloy Selection for Highly Corrosive Environments: Metallurgical and

Environmental Factors,” in Materials and Process Selection in Design, ASM Materials

Solutions, Cincinnati, Ohio, November 1999. Extended abstract published in Advanced

Materials and Processes, 156, October 1999. pp.: 71-72

54. R. B. Rebak, “Effect of Long Term Aging on the Property of C-22, C-4 and C-276 alloys

Weldments,” in the Workshop on the Fabrication and Welding of Nickel Alloys and

Other Materials for Radioactive Waste Containers, Las Vegas, Nevada, October 27-28,

1998

55. R. B. Rebak, “Localized Corrosion Resistance of HASTELLOY C-22, C-4 and C-276

Alloys as Candidate Materials for Nuclear Waste Repository: Effect of Alloy Aging at

427°C for up to 40,000 h,” Poster presented at the 1998 Gordon Research Conference on

Aqueous Corrosion, New London, New Hampshire, July 5-10, 1998

56. R. B. Rebak, “Candidate Materials for High Level Nuclear Waste Containers in Yucca

Mountain,” invited speaker to the Graduate Seminar Series in the Department of

Chemical Engineering of the University of Notre Dame, April 14, 1998

57. R. B. Rebak, “Corrosion Behavior of Nickel and Iron Base Alloys in Hydrofluoric

Acid,” invited speaker at the Corrosion/98 NACE International Task Group T-5A-36

Committee Meeting, San Diego, California, March 26, 1998

58. R. B. Rebak, “Mechanical Properties and Mechanical Resistance of Ni-Cr-Mo Alloys

after Aging at 427°C for 40,000 h,” invited speaker in the Workshop on Phase Stability in

Nickel Alloys for Radioactive Waste Containers, Sand Diego, California, March 19-20,

1998

29

59. R. B. Rebak and Z. Szklarska-Smialowska, “Effect of Mode of Loading on the SCC of

Alloy 600 in High Temperature Water, “ in Corrosion Research in Progress Symposium,

Session 3: Environmentally Assisted Cracking, Corrosion/94, Baltimore, Maryland,

February 27 March 4, 1994

60. R. B. Rebak, Z. Xia, and Z. Szklarska-Smialowska, “The Role of Carbides on Stress

Corrosion Cracking Susceptibility of Alloy 600 in High Temperature Water,” in

Corrosion Research in Progress Symposium, Session 3: Environmentally Cracking,

Corrosion/93, New Orleans, Louisiana, March 7-12, 1993

61. R. B. Rebak, “Stress Corrosion Cracking of Alloy 600 in Steam Generator Conditions,”

invited speaker at the Universidad de Buenos Aires, December 1992

62. R. B. Rebak and Z. Szklarska-Smialowska, “Crack Growth Rate in Alloy 600 in

Pressurized-Water-Reactor Primary Water,” in Corrosion Research in Progress

Symposium, Session 3: Environmentally Assisted Cracking, Corrosion/90, Las Vegas,

Nevada, April 23-27 1990

63. R. B. Rebak, “Susceptibilidad a la Corrosión Bajo Tensión del Latón en Soluciones de

Polifosfatos. I. Pirofosfato,” in proceedings of the V Congreso Argentino de

Fisicoquímica, April 27-30 1987, Mar del Plata, Argentina (1987)

Date post:	17-Feb-2017
Category:	Documents
Upload:	raul-rebak
View:	262 times
Download:	1 times

2014 12 22 Rebak Publications

Documents