+ All Categories
Home > Documents > 3281-MS-ELE-0005

3281-MS-ELE-0005

Date post: 02-Jun-2018
Category:
Upload: pradeep-kumar-maraptla
View: 224 times
Download: 0 times
Share this document with a friend

of 45

Transcript
  • 8/10/2019 3281-MS-ELE-0005

    1/45

  • 8/10/2019 3281-MS-ELE-0005

    2/45

    QP PROJECTNUMBER

    3281

    DATE 17/12/2013

    DOCUMENTREVISION

    Rev - 1

    No.

    1.1

    DOCUMENT TITLE Material Submittal for Power and Earthing cable

    QP COMMENTS CONTRACTOR RESPONSE

    The proposed vendor is in PVL andtherefore acceptable.

    Confirm.

    CONTRACT TITLE

    EPIC FOR REPAIR OF SERVICE BERTH NO.4,BUND FOR RECLAMATION AREA AT

    WAKRA DOCK RLC PORT AND NEW BERTH FOR MARPOL RECEPTION FACILITIERAS LAFFAN

    QP EXTERNAL TRANSMITTALREFERENCE

    EDR/GC12108800/EXT/TN/0629

    DOCUMENT NUMBER 3281-MS-ELE-0005

    COMMENTS RESOLUTIONSHEET [CRS]

    CONTRACT NUMBER GC12108800

    1.2

    Contractor to check if the leadsheathed cable for marpol berth areincluded as part of this materialsubmittal. Revise the informationaccordingly

    3281-MS-ELE-0005 REV # 01 Page 2 of 45

    Confirmed refer page No. 31 of Data Sheet

  • 8/10/2019 3281-MS-ELE-0005

    3/45

    MATERIAL SUBMITTAL FOR

    POWER AND EARTHING CABLES

    TABLE OF CONTENTS

    S.NO. DESCRIPTION PAGE NO.

    1 SCOPE OF THE DOCUMENT 4

    2 COMPLIANCE STATEMENT 6

    3 MANUFACTURE DETAILS 10

    4 AREA OF INSTALLATION 1 2

    5 DATA SHEET 1 4

    6 COMPANY PROFILE 3 4

    7 TEST CERTIFICATES 4 3

  • 8/10/2019 3281-MS-ELE-0005

    4/45

    MATERIAL SUBMITTAL FOR

    P OWER A ND EARTHING C ABLES

    S COPE OF THE DOCUMENT

  • 8/10/2019 3281-MS-ELE-0005

    5/45

    MATERIAL SUBMITTAL FOR

    P OWER A ND EARTHING C ABLES

    1. SCOPE OF THE DOCUMENT

    This document covers the Material Submittal for the POWER AND EARTHING CABLES to be

    utilized in this project EPIC FOR THE REPAIR OF THE SERVICE BERTH NO. 4, BUND FOR RECLAIMATION

    AREA AT WAKRA DOCK RLC PORT AND NEW BERTH FOR MARPOL RECEPTION FACILITIES AT RAS

    LAFFAN .

  • 8/10/2019 3281-MS-ELE-0005

    6/45

    MATERIAL SUBMITTAL FOR

    P OWER A ND EARTHING C ABLES

    COMPLIANCE STATEMENT

  • 8/10/2019 3281-MS-ELE-0005

    7/45

    ELECTRICAL POWER, CONTROL CABLES AND CABLES - REVISION A-QP Specification

    paragraph:QICC

    1.0 Noted

    2.0 QICC Comply 3.0 QICC Comply 4.0 QICC Comply 5.0 QICC Comply 5.1 QICC Comply 5.2 N/A 5.3 QICC Comply 5.4 Noted6.0 Noted6.1 QICC Comply

    6.1.1 QICC Comply 6.1.2 QICC Comply 6.2 QICC Comply 6.3 QICC Comply 6.4 QICC Comply 7.0 Noted

    TECHNICAL DEPARTMENT

    COMPLIANCE STATEMENT - QP SPECIFICATION ES.2.14.0070

    8.0 QICC Comply 8.1 QICC Comply 8.2 QICC Comply 8.3 QICC Comply 8.4 Noted8.5 Shall be submitted upon request9.0 QICC Comply 9.1 QICC Comply 9.2 QICC Comply 9.3 QICC Comply 9.4 QICC Comply 9.5 QICC Comply 9.6 QICC Comply 9.7 QICC Comply

    9.7.1 QICC Comply 9.7.2 QICC Comply 9.7.3 N/A 9.7.4 QICC Comply 9.8 QICC Comply

    9.8.1 QICC Comply 9.8.2 QICC Comply 9.8.3 QICC Comply 9.9 N/A

    9.10 N/A 10.010.1 Noted10.2 QICC Complies to IEC 6022810.3 QICC Comply

    3281-MS-ELE-0005 REV # 01 Page 7 of 45

  • 8/10/2019 3281-MS-ELE-0005

    8/45

    ELECTRICAL POWER, CONTROL CABLES AND CABLES - REVISION A-QP Specification

    paragraph:QICC

    TECHNICAL DEPARTMENT

    COMPLIANCE STATEMENT - QP SPECIFICATION ES.2.14.0070

    10.4 QICC Comply with XLPE Insulation

    10.5 QICC Comply 10.6 QICC Comply for Voltage above 6KV 10.7 QICC Comply 10.8 QICC Comply 10.9 QICC Comply with Galvanized steel wire Armour

    10.10 QICC Comply 10.10.1

    10.10.1.1 QICC Comply 10.10.1.2 N/A 10.10.2 N/A

    10.10.2.1 N/A 10.10.2.2 N/A

    10.11 QICC Comply 10.11.1 QICC Comply 10.11.2 QICC Comply 10.12 N/A

    10.12.1 N/A 10.12.1.1 N/A 10.12.1.2 N/A 10.12.2 N/A

    10.12.2.1 N/A 10.12.2.2 N/A 10.12.3 QICC Comply 10.12.4 N/A 10.13 QICC Comply

    10.13.1 QICC Comply 10.13.2 QICC Comply 10.13.3 QICC Comply 10.14 N/A

    10.14.1 N/A 11.0 Noted12.1 Our QA/QC system is based on ISO 9001-2008

    12.2.1 Type test will be done for 1 sample per typeClause 12.2.1.1 N/A (Applicable only for Oil Resistant Sheath)Clause 12.2.1.2 Comply

    Clause 12.2.1.3 Comply Clause 12.2.1.4 N/A Clause 12.2.1.5 Comply Clause 12.2.1.6 Comply Clause 12.2.1.7 N/A Clause 12.2.1.8 Comply Clause 12.2.1.9 Comply

    Clause 12.2.1.10 Comply Clause 12.2.1.11 N/A

    3281-MS-ELE-0005 REV # 01 Page 8 of 45

  • 8/10/2019 3281-MS-ELE-0005

    9/45

    ELECTRICAL POWER, CONTROL CABLES AND CABLES - REVISION A-QP Specification

    paragraph:QICC

    TECHNICAL DEPARTMENT

    COMPLIANCE STATEMENT - QP SPECIFICATION ES.2.14.0070

    Clause 12.2.2

    Clause 12.2.2.1 Comply as a Type testClause 12.2.2.2 Not ApplicableClause 12.2.2.3 Comply Clause 12.2.2.4 Comply Clause 12.2.2.5 Comply Clause 12.2.3

    Clause 12.2.3.1 Comply Clause 12.2.3.2 Comply Clause 12.2.3.3 Comply Clause 12.2.3.4 Comply Clause 12.2.3.5 Comply

    Clause 12.2.3.6 According to IEC standards this test is applicable for voltage above 6KV Clause 12.2.3.7 Comply as a Type testClause 12.2.3.8 Comply Clause 12.2.3.9 Comply

    Clause 13.1 Comply Clause 13.2 Comply Clause 14.0 Comply Clause 15.0 Comply Clause 16.0 Comply

    3281-MS-ELE-0005 REV # 01 Page 9 of 45

  • 8/10/2019 3281-MS-ELE-0005

    10/45

    MATERIAL SUBMITTAL FORPOWER AND EARTHING CABLES

    MANUFACTURER/SUPPLIERS DETAILS

  • 8/10/2019 3281-MS-ELE-0005

    11/45

    MATERIAL SUBMITTAL FORPOWER AND EARTHING CABLES

    M ATERIAL: POWER CABLES

    Source Details:

    Manufacturer Name Qatar International Cables Company- A Nexans Company

    Origin Paris

    P. O. Box 15991

    Telephone No. +974 44673009

    Email I.D. [email protected]

  • 8/10/2019 3281-MS-ELE-0005

    12/45

    MATERIAL SUBMITTAL FORPOWER AND EARTHING CABLES

    AR EA OF INSTALLATION

  • 8/10/2019 3281-MS-ELE-0005

    13/45

  • 8/10/2019 3281-MS-ELE-0005

    14/45

    MATERIAL SUBMITTAL FORPOWER AND EARTHING CABLES

    DATA SHEET

  • 8/10/2019 3281-MS-ELE-0005

    15/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    1x25Cu/PVC///// 0.45/0.75 kV IEC 60227

    DESCRIPTION0.45/0.75 kV PVC TI1 core with copper conductor

    21025MVZOUZ09AD0IEC 60227

    IEC 60332-1

    APPLICATIONSuitable for fixed installations at open air, in tube or canals andundergroundMax. Operation temperature: 70Max. Short circuit temperature : 160 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductor class 2

    2. Insulation:PVC

    3. Insulating Colour Sequence:G / Y

    4. Marking:450/750 V Cu / PVC 1 x 25 mm2 IEC 60227-3 Made In QATAR QICC - NexansYear Meters

    CHARACTERISTICSConstruction characteristics

    Conductor flexibility Stranded class 2Conductor shape Circular Material used for length water tightness NoneInsulating Material PVC TI1Insulation Nominal Thickness 1.2mmOverall diameter (7%) 8.4mmLength per drum 3000m

  • 8/10/2019 3281-MS-ELE-0005

    16/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Electrical characteristics

    Rated Voltage Uo/U (Um) Voltage range 450/750 V

    Frequency 50HzDC Resistance 0.727Ohm

    AC Resistance 0.9306Ohm AC Voltage test is 2.5KV for 5 mins

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility Rigid

    Usage characteristicsShort-circuit max. conductor temperature 160CMax. conductor temperature in service 70C

  • 8/10/2019 3281-MS-ELE-0005

    17/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    1x70Cu/PVC-FR///// 0.45/0.75 kV IEC 60227

    DESCRIPTION0.45/0.75 kV PVC TI1 - FR core with copper conductor

    21070MVZOUZ01AD0IEC 60227

    IEC 60332-1

    APPLICATIONSuitable for fixed installations at open air, in tube or canals andundergroundMax. Operation temperature: 70Max. Short circuit temperature : 160 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductor class 2

    2. Insulation:PVC

    3. Insulating Colour Sequence:G / Y

    4. Marking:450/750 V Cu / PVC- FR 1 x 70 mm2 IEC 60227-3 Made In QATAR QICC - NexansYear Meters

    CHARACTERISTICSConstruction characteristics

    Conductor flexibility Stranded class 2Conductor shape Circular Material used for length water tightness NoneInsulating Material PVC TI1 - FRInsulation Nominal Thickness 1.4mmOverall diameter (7%) 12.75mmLength per drum 3000m

  • 8/10/2019 3281-MS-ELE-0005

    18/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Electrical characteristics

    Rated Voltage Uo/U (Um) Voltage range 450/750 V

    Frequency 50HzDC Resistance 0.268Ohm

    AC Resistance 0.343Ohm AC Voltage test is 2.5KV for 5 mins

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility Rigid

    Usage characteristicsShort-circuit max. conductor temperature 160CMax. conductor temperature in service 70C

  • 8/10/2019 3281-MS-ELE-0005

    19/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    4x120Cu/XLPE/PVC//SWA//PVCFR 0.6/1/1.2 kV IEC 60502-1

    DESCRIPTION600/1000V XLPE steel wire armoured, four core cables with copper conductor

    24120BXZVSB01B20IEC 60502-1IEC 60332-3

    APPLICATIONPower use outdoor application, even wet.Suitable for fixed installations at open air, in tube or canals and undergroundMax. Operation temperature: 90Max. Short circuit temperature : 250 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductor class 2

    2. Insulation:Insulation Type XLPE Excellent heat resistance (90C) Good mechanical strength Excellent behavior under short circuit conditions (250C) Extremely good resistance to low temperatures

    3. Metallic screen layer:None

    4. Insulating Colour Sequence:Red - Yellow - Blue - Black

    5. Bedding / Filling:PVC ST2 Natural bedding layer applying over the core. "Bedding color can be black or Natural."

    6. Lead Sheathing:None.

    7. Separation Sheathing:None.

    8. Armour:

  • 8/10/2019 3281-MS-ELE-0005

    20/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Galvanized steel wire armour

    9. Outer sheath:PVC ST2 FR Cat A Natural, outer sheath layer applying over the armour layer. The outer sheath can beblack or as per customer requirement.

    10. Outer sheath colour:Black

    11. Marking:

    12. Packing: All drum types, lagged or not, up to a diameter of 3.0 m and a total weight of 13 tons. Drums can be woodenor steel. The length per drum as per customer requirement.

    Approximate drum size will be: DW-16

    CHARACTERISTICS

    Construction characteristicsConductor flexibility Stranded class 2Conductor shape Round compacted RMCMaterial used for length water tightness NoneInsulating Material XLPENominal Insulation Thickness 1.2mmMin @ Point 0.98mmScreen None

    Material of bedding / filling PVC ST2 Natural or BlackNominal Thickness 1.4mmMin @ Point 0.92mm

    Armour Type SWA Armour Wire Diameter 2.5mm 5%Outer sheath PVC ST2 FR Cat A NaturalNominal Thickness 2.5mmMin @ Point 1.8mmOuter sheathing colour Black or as per customer

    requirementOuter sheathing diameter 7% 49.5mmLength per drum 400m

    Electrical characteristicsRated Voltage Uo/U (Um) Voltage range 600/1000VFrequency 50HzTest voltage 3.5kVDC Resistance @ 20C 0.153 Ohm

    AC Resistance @ 90C 0.1958 OhmShort Circuit Current of Conductor 17.19 KA

    Approx. capacitance 0.756 F/KMCurrent Carry Capacity:Current Carry Capacity in Air 353A

    4 x 120 mm2 Cu / XLPE / PVC / SWA / PVC -FR 600/1000 V IEC 60502-1 MADE IN QATAR QICC-Nexans Year Meters

  • 8/10/2019 3281-MS-ELE-0005

    21/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Current Carry Capacity in Ground 257ACurrent Carry Capacity in Ground Duct 223AInstallation Condition:

    Air temperature (Deg) 30Ground temperature (Deg) 20Depth of lay (m) 0.7Soil thermal resistivity (K.m/W) 2.5

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility Rigid

    Approx. Bending radius 5 % 396mm Approx. Max pulling force 24 KN

    Usage characteristicsShort-circuit max. conductor temperature 250CMax. conductor temperature in service 90C

  • 8/10/2019 3281-MS-ELE-0005

    22/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    4x240Cu/XLPE/PVC//SWA//PVCFR 0.6/1/1.2 kV IEC 60502-1

    DESCRIPTION600/1000V XLPE steel wire armoured, four core cables with copper conductor

    24240BXZVSB01B20IEC 60502-1IEC 60332-3

    APPLICATIONPower use outdoor application, even wet.Suitable for fixed installations at open air, in tube or canals and undergroundMax. Operation temperature: 90Max. Short circuit temperature : 250 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductor class 2

    2. Insulation:Insulation Type XLPE Excellent heat resistance (90C) Good mechanical strength Excellent behavior under short circuit conditions (250C) Extremely good resistance to low temperatures

    3. Metallic screen layer:None

    4. Insulating Colour Sequence:Red - Yellow - Blue - Black

    5. Bedding / Filling:PVC ST2 Natural bedding layer applying over the core. "Bedding color can be black or Natural."

    6. Lead Sheathing:None.

    7. Separation Sheathing:None.

    8. Armour:

  • 8/10/2019 3281-MS-ELE-0005

    23/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Galvanized steel wire armour

    9. Outer sheath:PVC ST2 FR Cat A Natural, outer sheath layer applying over the armour layer. The outer sheath can beblack or as per customer requirement.

    10. Outer sheath colour:Black

    11. Marking:

    12. Packing: All drum types, lagged or not, up to a diameter of 3.0 m and a total weight of 13 tons. Drums can be woodenor steel. The length per drum as per customer requirement.

    Approximate drum size will be: DW-25

    CHARACTERISTICS

    Construction characteristicsConductor flexibility Stranded class 2Conductor shape Round compacted RMCMaterial used for length water tightness NoneInsulating Material XLPENominal Insulation Thickness 1.7mmMin @ Point 1.43mmScreen None

    Material of bedding / filling PVC ST2 Natural or BlackNominal Thickness 1.6mmMin @ Point 1.08mm

    Armour Type SWA Armour Wire Diameter 2.5mm 5%Outer sheath PVC ST2 FR Cat A NaturalNominal Thickness 3mmMin @ Point 2.2mmOuter sheathing colour Black or as per customer

    requirementOuter sheathing diameter 7% 66.2mmLength per drum 400m

    Electrical characteristicsRated Voltage Uo/U (Um) Voltage range 600/1000VFrequency 50HzTest voltage 3.5kVDC Resistance @ 20C 0.0754 Ohm

    AC Resistance @ 90C 0.0965 OhmShort Circuit Current of Conductor 34.32 KA

    Approx. capacitance 0.773 F/KMCurrent Carry Capacity:Current Carry Capacity in Air 546A

    4 x 240 mm2 Cu / XLPE / PVC / SWA / PVC -FR 600/1000 V IEC 60502-1 MADE IN QATAR QICC-Nexans Year Meters

  • 8/10/2019 3281-MS-ELE-0005

    24/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Current Carry Capacity in Ground 375ACurrent Carry Capacity in Ground Duct 324AInstallation Condition:

    Air temperature (Deg) 30Ground temperature (Deg) 20Depth of lay (m) 0.7Soil thermal resistivity (K.m/W) 2.5

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility Rigid

    Approx. Bending radius 5 % 530mm Approx. Max pulling force 48 KN

    Usage characteristicsShort-circuit max. conductor temperature 250CMax. conductor temperature in service 90C

  • 8/10/2019 3281-MS-ELE-0005

    25/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    4x10Cu/XLPE//LS/SWA//PVCFR 0.6/1/1.2 kV IEC 60502-1

    DESCRIPTION600/1000V XLPE steel wire armoured, four core cables with copperconductor

    24010BXZVSB01BO0IEC 60502-1IEC 60332-3

    APPLICATIONPower use outdoor application, even wet.Suitable for fixed installations at open air, in tube or canals and undergroundMax. Operation temperature: 90Max. Short circuit temperature : 250 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductorclass 2

    2. Insulation:Insulation Type XLPE Excellent heat resistance (90C) Good mechanical strength Excellent behavior under short circuit conditions (250C) Extremely good resistance to low temperatures

    3. Metallic screen layer:None

    4. Insulating Colour Sequence:Red - Yellow - Blue - Black

    5. Bedding / Filling:PVC Filling Compound

    6. Lead Sheathing:Lead Ingots Alloy 1/2C

    7. Separation Sheathing:PVC ST2 Natural

    8. Armour:

  • 8/10/2019 3281-MS-ELE-0005

    26/45

  • 8/10/2019 3281-MS-ELE-0005

    27/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Current Carry Capacity in Ground 65ACurrent Carry Capacity in Ground Duct 58AInstallation Condition:

    Air temperature (Deg) 30Ground temperature (Deg) 20Depth of lay (m) 0.7Soil thermal resistivity (K.m/W) 2.5

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility RigidApprox. Bending radius 5 % 302mmApprox. Max pulling force 2 KN

    Usage characteristicsShort-circuit max. conductor temperature 250CMax. conductor temperature in service 90C

  • 8/10/2019 3281-MS-ELE-0005

    28/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    4x25Cu/XLPE//LS/SWA//PVCFR 0.6/1/1.2 kV IEC 60502-1

    DESCRIPTION600/1000V XLPE steel wire armoured, four core cables with copperconductor

    24025BXZVSB01BO0IEC 60502-1IEC 60332-3

    APPLICATIONPower use outdoor application, even wet.Suitable for fixed installations at open air, in tube or canals and undergroundMax. Operation temperature: 90Max. Short circuit temperature : 250 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductor class 2

    2. Insulation:Insulation Type XLPE Excellent heat resistance (90C) Good mechanical strength Excellent behavior under short circuit conditions (250C) Extremely good resistance to low temperatures

    3. Metallic screen layer:None

    4. Insulating Colour Sequence:Red - Yellow - Blue - Black

    5. Bedding / Filling:PVC Filling Compound

    6. Lead Sheathing:Lead Ingots Alloy 1/2C

    7. Separation Sheathing:PVC ST2 Natural

    8. Armour:

  • 8/10/2019 3281-MS-ELE-0005

    29/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Galvanized steel wire armour

    9. Outer sheath:PVC ST2 FR Cat A Natural, outer sheath layer applying over the armour layer. The outer sheath can beblack or as per customer requirement.

    10. Outer sheath colour:Black

    11. Marking:

    4 x 25 mm2 Cu / XLPE / / Lead / / SWA / PVC FR 600/1000 V IEC 60502-1 MADE IN QATAR QICC-Nexans Year Meters

    12. Packing:A ll drum types, lagged or not, up to a diameter of 3.0 m and a total weight of 13 tons. Drums can be woodenor steel. The length per drum as per customer requirement.Approximate drum size w ill be: DW-18

    CHARACTERISTICS

    Construction characteristicsConductor flexibility Stranded class 2Conductor shape Round compacted RMCMaterial used for length water tightness NoneInsulating Material XLPENominal Insulation Thickness 0.9mmMin @ Point 0.71mmScreen None

    Material of bedding / filling PVC Filling CompoundNominal Thickness 1mmMin @ Point 0.6mmArmour Type SWALead sheath thickness Nominal = 1.27mm Min @ point = 1.11mmSeparation sheath thickness Nominal = 1.1mm Min @ point = 0.68mmArmour Wire Diameter 1.6mm 5%Outer sheath PVC ST2 FR Cat A NaturalNominal Thickness 1.9mmMin @ Point 1.32mmOuter sheathing colour Black or as per customer requirementOuter sheathing diameter 7% 32mmLength per drum 1000m

    Electrical characteristicsRated Voltage Uo/U (Um) Voltage range 600/1000VFrequency 50HzTest voltage 3.5kVDC Resistance @ 20C 0.727 OhmAC Resistance @ 90C 0.9306 OhmShort Circuit Current of Conductor 3.58 KAApprox. capacitance 0.498 F/KMCurrent Carry Capacity:Current Carry Capacity in Air 131A

  • 8/10/2019 3281-MS-ELE-0005

    30/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Current Carry Capacity in Ground 107ACurrent Carry Capacity in Ground Duct 96AInstallation Condition:

    Air temperature (Deg) 30Ground temperature (Deg) 20Depth of lay (m) 0.7Soil thermal resistivity (K.m/W) 2.5

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility RigidApprox. Bending radius 5 % 384mmApprox. Max pulling force 5 KN

    Usage characteristicsShort-circuit max. conductor temperature 250CMax. conductortemperature in service 90C

  • 8/10/2019 3281-MS-ELE-0005

    31/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    4x95Cu/XLPE/PVC/LS/SWA//PVCFR 0.6/1/1.2 kV IEC 60502-1

    DESCRIPTION600/1000V XLPE steel wire armoured, four core cables with copperconductor

    24095BXZVSB01B2OIEC 60502-1IEC 60332-3

    APPLICATIONPower use outdoor application, even wet.Suitable for fixed installations at open air, in tube or canals and undergroundMax. Operation temperature: 90Max. Short circuit temperature : 250 (Max 5 s)

    CONSTRUCTION

    1. Conductor:Compacted Round conductorclass 2

    2. Insulation:Insulation Type XLPE Excellent heat resistance (90C) Good mechanical strength Excellent behavior under short circuit conditions (250C) Extremely good resistance to low temperatures

    3. Metallic screen layer:None

    4. Insulating Colour Sequence:Red - Yellow - Blue - Black

    5. Bedding / Filling:PVC ST2 Natural bedding layer applying over the core. "Bedding color can be black or Natural."

    6. Lead Sheathing:Lead Ingots Alloy 1/2C

    7. Separation Sheathing:PVC ST2 Natural

    8. Armour:

  • 8/10/2019 3281-MS-ELE-0005

    32/45

  • 8/10/2019 3281-MS-ELE-0005

    33/45

    TECHNICAL DATA SHEET ContactQICC-NexansPhone: +97444085100Email:[email protected]

    Current Carry Capacity in Ground 226ACurrent Carry Capacity in Ground Duct 197AInstallation Condition:

    Air temperature (Deg) 30Ground temperature (Deg) 20Depth of lay (m) 0.7Soil thermal resistivity (K.m/W) 2.5

    Mechanical characteristicsMechanical resistance to impacts GoodCable flexibility RigidApprox. Bending radius 5 % 608mmApprox. Max pulling force 19 KN

    Usage characteristicsShort-circuit max. conductor temperature 250CMax. conductor temperature in service 90C

  • 8/10/2019 3281-MS-ELE-0005

    34/45

    MATERIAL SUBMITTAL FOR

    POWER AND EARTHING CABLES

    CO MPANY PROFILE

  • 8/10/2019 3281-MS-ELE-0005

    35/45

    3281-MS-ELE-0005 REV # 01 Page 35 of 45

  • 8/10/2019 3281-MS-ELE-0005

    36/45

    3281-MS-ELE-0005 REV # 01 Page 36 of 45

  • 8/10/2019 3281-MS-ELE-0005

    37/45

    3281-MS-ELE-0005 REV # 01 Page 37 of 45

  • 8/10/2019 3281-MS-ELE-0005

    38/45

    3281-MS-ELE-0005 REV # 01 Page 38 of 45

  • 8/10/2019 3281-MS-ELE-0005

    39/45

    3281-MS-ELE-0005 REV # 01 Page 39 of 45

  • 8/10/2019 3281-MS-ELE-0005

    40/45

    3281-MS-ELE-0005 REV # 01 Page 40 of 45

  • 8/10/2019 3281-MS-ELE-0005

    41/45

    3281-MS-ELE-0005 REV # 01 Page 41 of 45

  • 8/10/2019 3281-MS-ELE-0005

    42/45

    3281-MS-ELE-0005 REV # 01 Page 42 of 45

  • 8/10/2019 3281-MS-ELE-0005

    43/45

    MATERIAL SUBMITTAL FOR

    POWER AND EARTHING CABLES

    TES T CERTIFICATES

  • 8/10/2019 3281-MS-ELE-0005

    44/45

    3281-MS-ELE-0005 REV # 01 Page 44 of 45

  • 8/10/2019 3281-MS-ELE-0005

    45/45


Recommended