36 DOUBLE HEAD ANCHOR - Triad Mobile Home Supplytriadmobilehomesupply.com/catalog/section_07.pdf ·...

NU-CONCEPT ANCHORS WITH STABILIZER CAP

30" DOUBLE HEAD ANCHOR

HAS TWO 4" SHARPENED HELIX

Suitable for use in class 2 & 3 soil

The 6"diameter swivel stabilizer cap is approved for use on anyand all Minute Man anchors. Simply slide cap over anchor headand install included bolt, then continue to screw anchor into theground until the flat surface of the cap is at or below ground level.

Part Number Description Price3-3476 3/4" DIA. SHAFT $7.983-3476-96 96 to 199 $7.183-3476-200 200 & up $7.183-3479 7/8" DIA. SHAFT $10.32

STABILIZER CAP, See 3-3555


HAS ONE 6" AND ONE 4" SHARPENED HELIX 3/4" DIA. SHAFT

Suitable for class 2, 3 & 4 soil

Part Number Price3-3477 $9.69


HAS ONE 6" SHARPENED HELIX 5/8" DIA. SHAFT

Suitable for class 2, 3 & 4 soil


E-Z ONE-STEP STABILIZED ANCHORING

Combines anchor & stabilizer as one unit. Reduces installationtime by 50% over separate anchor & separate plate installation.

30 inch long, 3/4 inch diameter shaft, double head with two 4

inch diameter sharpened disc.

Suitable for use in class 2 & 3 soil


DOUBLE HEAD BARBED ROCK ANCHOR

This anchor is designed to be driven into a 1-1/4" Dia. hole drilled 8" deep into solid rock.

24 Inches long, 23/32 inch dia shaft with double head

Head slides down over anchor shaft for ease of driving anchor into rock.


*Prices are Subject to Change without Notice.*

(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 144

DOUBLE HEAD ROCK CROSS ANCHOR

Comes with two 36" x 3/4" rods.

Must be used in solid rock.


CONCRETE ANCHOR “L” Shaped

For use when pouring concrete.

Part Number Description Price3-3498 PAINTED STEEL $3.983-3498G GAL. STEEL $5.89

DOUBLE HEAD PATIO ANCHOR

For use in existing concrete. Split strap bolts are soldseparately. Made of heavy gauge painted steel.Comes with expansion bolt.


FRAME TIE WITH HOOK

Attach frame clamp (hook) on inside top flange ofhome I-beam. Bring galvanized strap between floor and I-beam. Go around I-beam one completeturn, pull strap tight and attach to split bolt onanchor tensioning head.

Part Number Description Price3-3488 7 FT. FRAME TIE $3.263-3488-96 96 & UP $2.943-3489 10 FT. FRAME TIE $3.983-3489-96 96 & UP $3.59

FRAME TIE WITH BUCKLE

Has 10 ft. long strap

Part Number Description Price3-3487 1 THRU 95 $3.953-3487-96 96 & UP $3.56

LOCKING FRAME CLAMP II

MMA-33 ASSEMBLED UNIT Shown as an assembled unit, but sold separately. Clamp comeswith a plated grade-5 bolt & nut. Strap comes with attached pivot clip with bolt hole to attach to frame clamp.

Part Number Description Price3-3473 10 FT. STRAP & CLIP $4.193-3473-96 96 & UP $3.773-3474 CLAMP ONLY $2.683-3474-96 96 & UP $2.42

CORNER TIE With Galvanized Strap

This galvanized steel pivot clip is bent at a 45 degree angle with one 1/2" diameter hole. The attached galvanized steel strap is 7 feet long. Designed mainly for use with longitudinal frame clamp # 3-3475.




LONGITUDINAL FRAME CLAMP We stock the four bolt type for use in wind zone I. Consists oftwo top plates, one bottom plate and four plated grade-5 bolts. Clamp mounts on bottom of I-Beam as shown. Note: Use strap & pivot clip # 3-3472


BUCKLE

Made of heavy galvanized steel.

Part Number Description Price3-3484 SINGLE SLOT $0.643-3485 DOUBLE SLOT $0.49

CRIMPS

For use with steel strapping.


STRAPPING 1-1/4" x .035 thick galvanized steelstrap. Stamped as per ANSI code & Staterequirements.

Part Number Description Price3-3494 37 ft. $10.983-3495 600 ft. $149.00

GALVANIZED STRAPPING

This strapping is used to tie modular homesto the foundation sill plate. Twenty -four (24) gauge galvanized steel. Two inches(2") wide x sixteen inches (16") long.


ANCHOR BOLT WITH NUT Plated steel split bolt and nut for use with strap.


ROOF BRACKET We stock both galvanized steel and aluminum roof brackets. Both type are made of heavy gauge material to withstand high stress levels exerted by high winds.

Part Number Description Price3-3490 GALVANIZED STEEL $5.593-3491 ALUMINUM $5.98

FRAME TIE HOOK For use with tie down strapping. Made of heavy gauge galvanized steel.


CARRIAGE BOLT

Grade 5 plated steel bolt and nut. Part Number Description Price3-3469 1/2" x 1-1/4" $0.69

ADJUSTABLE OUTRIGGERS Eliminates perimeter blocking, problems with anchor spacing, andinterference with skirting. Outer wall settling is greatly reduced.

Easy to install and are tested & approved.

Part Number Description Price3-3550 FOR 14 FT. WIDE HOMES $14.493-3551 FOR 16 FT. WIDE HOMES $17.35



STABILIZER CAP Designed for attaching to the head of Nu-Concept Minute Man anchors. Used instead ofthe drive-in style stabilizing plate. Cap is 6"dia. and 1"deep. Comes with bolt to secure toanchor. Comes 16 in a box.

Part Number Description Price3-3555 1 thru 95 $4.193-3555-96 96 to 200 $4.073-3555-200 200 & up $3.95

STABILIZER for ANCHORS This stabilizer has been designed to meet theN.C. state code effective Jan. 15, 1991. Wastested and approved for use without the useof a U-bolt to hold the anchor against thestabilizer plate. Made of heavy gage paintedsteel.


ANCHOR FLANGE Concrete Dry Set

This dry set anchor flange is used insteadof using the pier pad pan. Longitudinal orlateral brace tubes may be connected tothis device. Comes with one 1/2" x 1-1/2" long carriage bolt and two 5/8" x 3" longshield anchors for concrete. MMCAF 24 per box.


ANCHORING KIT for UTILITY BUILDINGS This system is designed for small to medium size storage/utilitybuildings. Comes with four painted eye anchors that are 30” with 1/2" diameter shaft and has one 3" diameter sharpened helix. Has50 feet of 6-strand-20 gauge galvanized steel cable and four zinccoated u-bolt clamps with nuts. Kit weighs 8 pounds.




Minute Man, Brace System for Soil

THE MINUTE MAN FOUNDATION SYSTEM EXCEEDS REQUIREMENTS

FOR ALL WIND ZONES

Eliminates or reduces most anchors and hardware, saving time and money

ZONE I, II & III LONGITUDINAL AND LATERAL BRACING SYSTEMS FOR SOIL INSTALLATIONS

Ground anchors may not be required on double wide homes.Marriage wall and perimeter wall anchors must be used when calledfor by home manufacturer. 3,150 lb. working load ground anchorswith stabilizers and frame ties are required on 4 corners of all single

wide homes. Systems must be as equally spaced as possible and no more than 10 ft. from the end of the home. Triple wide homes and tagunits require two additional systems.

Part Number Description Price3-3580 PIER PAD, 20" x 20", GALVANIZED STEEL (MMSPP), (4 ea. 16" long drive pins and

2 ea. 1/2" x 2-1/2" long bolts/nuts)$42.76

3-3584 LATERAL BRACE TUBE KIT with hardware, 60" to 96", (EACH package contains: 2ea. brace tubes, 2 ea. 2" x 7-3/4" lateral clamps, 2 ea. 1-5/8" x 2" tube clamp, 4 ea.1/2" x 2-1/2" bolt/nut, 4 ea. 1/2" x 1-3/8" washers, 2 ea. 1/2" x 1-1/4" bolt/nut, 8 ea. 1/4"x 3/4" self drilling screws). Two Lateral brace tubes with hardware per pkg., pricedseparately.

$48.89

3-3585 LATERAL BRACE TUBE HARDWARE KIT (Each hardware kit contains enoughproduct to install two tubes)

$18.98

3-3586 LONGITUDINAL BRACE TUBE, 39" LONG With Hardware $24.983-3587 LONGITUDINAL BRACE TUBE, 44" LONG With Hardware $27.003-3588 LONGITUDINAL BRACE TUBE, 53" LONG With Hardware $29.663-3589 LONGITUDINAL BRACE TUBE, 65" LONG With Hardware (EACH package contains:

2 ea. Brace tubes, 2 ea. Preassembled beam clips, 4 ea. 3-3/4" x 2-3/4" top coverattachment clips, 8 ea. 1/2" x 1-1/4" bolt/nut.) Two longitudinal brace tubes withhardware per pkg, priced separately.

$32.79

3-3592 LONGITUDINAL BRACE TUBE HARDWARE KIT (MMLBC) (EACH hardware kitcontains enough product to install two tubes)

$23.00

Note: Hardware kits are stocked for those customers that loose or misplace those that came with the brace tubes. 12" THRU 24" HIGH PIER REQUIRES: 39" LONG LONGITUDINAL BRACE TUBES 12" THRU 32" HIGH PIER REQUIRES: 44" LONG LONGITUDINAL BRACE TUBES 12" THRU 40" HIGH PIER REQUIRES: 53" LONG LONGITUDINAL BRACE TUBES 12" THRU 48" HIGH PIER REQUIRES: 65" LONG LONGITUDINAL BRACE TUBES Note: Longitudinal & lateral brace tubes must have an angle of between 10 degrees and 45 degrees.

YOUR SET MUST BE DESIGNED BY A REGISTERED PROFESSIONAL ENGINEER IF ANY OF THE FOLLOWING CONDITIONS EXIST: • SITE LOCATION IS WITHIN 1,500 FT. OF COAST LINE • PIER HEIGHT EXCEEDS 48 INCHES • ROOF EAVES EXCEED 16 INCHES • SIDEWALL HEIGHT EXCEEDS 96 INCHES • MAIN I-BEAM SPACING EXCEEDS 99.5 INCHES



Minute Man, Flex Brace System for Dry & Wet Concrete

THE MINUTE MAN FOUNDATION SYSTEM EXCEEDS REQUIREMENTS

FOR ALL WIND ZONES

Eliminates or reduces most anchors and hardware, saving time and money

ZONE I, II & III LONGITUDINAL AND LATERAL FLEX BRACING SYSTEMS FOR DRY AND WET CONCRETE

INSTALLATIONS Ground anchors may not be required on double wide homes.Marriage wall and perimeter wall anchors must be used when calledfor by home manufacturer. 3,150 lb. working load ground anchorswith stabilizers and frame ties are required on 4 corners of all single

wide homes. Systems must be as equally spaced as possible and no more than 10 ft. from the end of the home. Triple wide homes and tagunits require two additional systems.

Part Number Description Price3-3623 LATERAL FLEX BRACE TUBE KIT with hardware, 60" to 96", (EACH package

contains: 2 ea. brace tubes, 2 ea. 2" x 7-3/4" lateral clamps, 2 ea. 1/2" x 2-1/2"bolt/nut, 2 ea. 1/2" x 1-3/8" washers, 8 ea. 1/4" x 3/4" self drilling screws and 2 ea. 5/8"x 3" sleeve anchors for dry concrete.) Two Lateral flex brace tubes with hardware perpkg., priced separately.

$53.00

3-3625 LATERAL FLEX BRACE TUBE HARDWARE KIT (Each hardware kit contains enoughproduct to install two tubes)

$17.98

3-3628 LONGITUDINAL FLEX BRACE TUBE, 39" LONG With Hardware $25.003-3629 LONGITUDINAL FLEX BRACE TUBE, 44" LONG With Hardware $26.793-3630 LONGITUDINAL FLEX BRACE TUBE, 53" LONG With Hardware (EACH package

contains: 2 ea. Brace tubes, 2 ea. Preassembled beam clips, 4 ea. 3-3/4" x 2-3/4" topcover attachment clips, 8 ea. 1/2" x 1-1/4" bolt/nut and 2 ea. 5/8" x 3" sleeve anchorsfor dry concrete.) Two longitudinal brace tubes with hardware per pkg, pricedseparately.

$28.00

3-3631 LONGITUDINAL FLEX BRACE TUBE HARDWARE KIT (Each hardware kit containsenough product to install two tubes)

$26.98

3-3632 L-ANCHOR FOR WET CONCRETE, 4 per box, priced each not per box (Comes withwasher and nut)

$3.49

18" THRU 24" HIGH PIER REQUIRES: 39" LONG LONGITUDINAL BRACE TUBES



Note: Longitudinal & lateral brace tubes must have an angle of between 10 degrees and 45 degrees. Note: Hardware kits are stocked for those customers that loose or misplace those that came with the brace tubes.

YOUR SET MUST BE DESIGNED BY A REGISTERED PROFESSIONAL ENGINEER IF ANY OF THE FOLLOWING CONDITIONS EXIST:

• SITE LOCATION IS WITHIN 1,500 FT. OF COAST LINE • PIER HEIGHT EXCEEDS 48 INCHES

• ROOF EAVES EXCEED 16 INCHES • SIDEWALL HEIGHT EXCEEDS 96 INCHES

• MAIN I-BEAM SPACING EXCEEDS 99.5 INCHES



Lateral & Longitudinal Pan System

LATERAL AND LONGITUDINAL PAN SYSTEM

by OLIVER TECHNOLOGIES

for HOME SETS

in NORTH CAROLINA

No ground anchors are required on double wide homes.

Two ground anchors are required on each side of singe wide homes and are to be located within two feet from the end with a minimum pull of 3150 lb.

Homes longer than 76 feet have additional requirements.

State of North Carolina only. Brace tubing must be galvanized, when the home manufacturers installation instructions are not available, vertical all tie-downs must be installed not to exceed 8 feet on centers. (wind zone II)

EACH SYSTEM CONSISTS OF THE FOLLOWING ITEMS: GROUND PAN (2.5” DEEP), 1 each CENTERPOINT BRACKET, 1 each U-BRACKET, 1 each 1/2” x 3/16” WASHER, 2 each BOLTS, GRADE 2 (1/2” DIA. x 1” LONG), 2 each NUTS (1/2” HEX), 2 each LONGITUDINAL I-BEAM CLAMP, 4 each I-BEAM FORM CLAMP WITH FLAT CLAMP, 1 each BOLT BAG, LONGITUDINAL BRACING, 1 each BOLT BAG, LATERAL BRACING, 1 each 5’ LATERAL ARM (1.25” & 1.5”) GALVANIZED, 1 each LONGITUDINAL ARMS, GALVANIZED, 2 each Note: Model number is NC 1100 I”V” COMPLETE SYSTEM WITH 39” LONG LONGITUDINAL BRACE ARMS 3-3615 (For 24” to 35” pier height) COMPLETE SYSTEM WITH 44” LONG LONGITUDINAL BRACE ARMS 3-3620 (For 30” to 40” pier height) Note: Longitudinal brace tubes must have a minimum of 40 degree and a maximum of 60 degree angle.

If the following conditions occur, STOP!!! Call Oliver Technologies, Inc. @ 1-800-284-7437: A. Pier height exceeds 48”. B. Roof eaves exceed 16”. C. Roof pitch greater than 7/12. D. Location is within 1500 feet of coast line. E. The following soil conditions; loose sands, firm clays and silts and alluvial fills (soil deposited by flowing water).

Part Number Description Price3-3615 COMPLETE SYSTEM WITH 39" LONG LONGITUDINAL BRACE ARMS $159.003-3620 COMPLETE SYSTEM WITH 44" LONG LONGITUDINAL BRACE ARMS $164.00



ANCHOR MACHINE by

MINUTE MAN PRODUCTS INC. Frame is made of welded tubular steel. 115-120 volt motordevelops a minimum of 600 lb. of torque. Has pressure sensitiveon/off switch for safer operation. Toggle style forward/reverseswitch allows for clockwise or counter clockwise operation. Has a27" long extension handle. Ninety (90) day limited warranty onparts and labor. Sold with adapter head.

Part Number Description Price3-3560 12 RPM, 1/2 HP MOTOR $898.00

"T" Style

ADAPTERS for

ANCHORING MACHINES These “T” style adapters are made of 3/16" thicksquare steel. Fits square anchoring machine shaftsonly. Comes in 3/4" and 1-1/8" sizes only.

Part Number Description Price3-3541 3/4" x 3/4" $32.003-3544 1-1/8" x 1-1/8" $32.00

Heavy Duty

ADAPTERS for

ANCHORING MACHINES This heavy duty adapter fits over the entirehead of all popular anchors. Simply slip theadapter over the anchor head, install theanchor into the ground, then slip theadapter off the anchor, saving time.

Part Number Description Price3-3545 FITS 1" SQUARE SHAFT $45.003-3546 FITS 3/4" SQUARE SHAFT $55.00

ELECTRICAL SWITCHES Anchoring Machines

Rated 10 amps @ 125 vac, 1/2 hp rated

Part Number Description Price3-3717 ON-OFF TOGGLE SWITCH $17.983-3719 FORWARD/REVERSE SWITCH $17.98

DIGITAL LEVELING SYSTEM

This electronic water level can beused outside or inside the home.Reads in inches and tenths. Willlevel to .2" (1/5") over entire lengthof 100’ tubing. Magnet holds digitaldisplay in place when necessary.Uses a 9-volt battery to power electronics. Uses RV anti-freeze or water as sensing agent. 90 day manufacturer’s warranty.




DOUBLE-WIDE ROLLERS

3-ROLLER STYLE

Top plate is of 1/2" thick plate steel, sides are of 3/8" thick steel,capable of supporting 27,000 lb. Each roller has three sealed ballbearing rollers of seamless steel. Overall dimensions: 9" wide x 9"long. Rolls on a user provided 4” x 8” timber, steel beam orequivalent, all capable of supporting weight of section beingmoved. Comes 3 per set.


DOUBLE-WIDE ROLLERS

5-ROLLER STYLE

Top plate is of 1/2" thick plate steel, sides are of 3/8" thick steel,capable of supporting approximately 48,000 lb. The two main unitshave five sealed ball bearing rollers of seamless steel. Thetongue/jack unit has three rollers. Overall dimensions: 9" wide x17" long. Rolls on a user provided 4” x 8” timber, steel beam orequivalent, all capable of supporting weight of section beingmoved. Comes 3 per set.


CRIMPING TOOL for

STRAP SEALS Part Number Price3-3505 $277.00

SOIL TEST PROBE This 60 inch long probe is used to test the earths soil density. Use inch pound readings to determine which anchor to use to resist at least 4170 pounds of pull. Comes with wrench adapter and 600 inch pound torque wrench.


MAGNETIC VALVE ASSEMBLY

for WATER LEVEL

Has 1-3/4" diameter magnet. Brass valvehas barbed fitting to accept 1/4" inside diameter plastic tubing.


POCKET PENETROMETER

by ELE

Used to determine thecompression strength of topsoil. Use reading to determineproper depth to place footers.

Part Number Description Price3-3504 PENETROMETER $98.003-3508 ADAPTER FOOT $39.00

GFCI CORD SET

Ground fault circuit interrupter is made of safety-yellow materials, Has a nine inch 12/3 AWG cord. 115 volt, 15 amp, 1800 watt outdoor UL listed. Plugs directly into receptacle. Do not use an extension cord between wall receptacle and GFCI.




CONTROL SCREW ASSEMBLY Replacement screw assembly for model 24-36 double wide dollykit by Double Wide Systems Co. Overall length is 33 inches.


COME-A-LONG This 2 ton capacity power pull has a steel cable with die castlocking hooks.


PLUMBING VENTS All listed vents are designed for flat orslightly pitched roofs.

Part Number Description Price3-3510 2-3/8" I.D., METAL $4.393-3511 2-3/8" I.D., PLASTIC $2.493-3512 5" I.D., METAL $7.79

ROOF FLASHING (Galvanized)

Fits 1-1/4" & 1-1/2" ABS or PVC pipe.


ROOF VENT Static Type

Made of galvanized steel. Overallheight is 3-3/4", nailing flange is16" x 15". Top hood is 11-1/2" square. Has 9" square opening.Small louvered openings preventsinsects from entering the atticspace. Not for roofs over 6/12pitch slope. Net free area is 50square inches.


RV VENT by

VENTLINE Body is made of galvanized steel,unlike those that are made of plastic,these will not crack along the baseand sides creating water leaks. Topcover is of white plastic.

Part Number Description Price3-3520 VENT WITH WHITE COVER $29.893-3525 COVER ONLY, WHITE $12.59

SKYLITES by SUN-TEC Smoke Tinted Double Pane

Unbreakable polycarbonate seamless outer pane protects againstleaking, damage and intrusion. Inner pane is made of clearpolycarbonate. Unique ventilation system prevents fogging andcondensation. High-tech engineered polycarbonate blocks over97% of ultra-violet light. Comes with pre-punched flanges ready to mount over roof opening of metal or sloped (3/12 pitch or greater)shingle roof. 5-year limited product warranty. *=Rough opening size.

Part Number Description Price3-FDE1632 16" x 32" (*14-1/4" x 30-1/4") $69.003-FDE1648 16" x 48" (*14-1/4" x 46-1/4") $87.503-FDE2246 22" x 46" (*21-1/2" x 46-1/2") $98.003-FDE2525 25" x 25" (*22-1/2" x 22-1/2") $69.003-FDE2432 24" x 32" (*22-1/4" x 30-1/4") $79.00

SHIPPING WEIGHT 16"x32" 06 LBS.

16"x48’ 10 LBS. 22"x46" 12 LBS. 25"x25" 08 LBS. 24"x32" 10 LBS.

46”x46” 25 LBS.

3-FDE4646 46" x 46" (*46-1/2" x 46-1/2") $198.00



Antique Style, Plastic

HOUSE NUMBERS Antique style house numbers of black plastic that are 4 inches tall. Comes with mounting screws.

Part Number Description Price3-5000 #0 $0.893-5001 #1 $0.893-5002 #2 $0.893-5003 #3 $0.893-5004 #4 $0.893-5005 #5 $0.893-5006 #6 $0.893-5007 #7 $0.893-5008 #8 $0.893-5009 #9 $0.89

Elegant Style, Solid Brass

HOUSE NUMBERS Elegant style house numbers of solid brass that are 4 inches tall. Comes with mounting screws.

Part Number Description Price3-5020 #0 $2.893-5021 #1 $2.893-5022 #2 $2.893-5023 #3 $2.893-5024 #4 $2.893-5025 #5 $2.893-5026 #6 $2.893-5027 #7 $2.893-5028 #8 $2.893-5029 #9 $2.89



Contact Cement

WELDWOOD THE ORIGINAL

CONTACT CEMENT Fast dry formula exceeds industry performancerequirements. Dries in 15-20 minutes. Highheat resistance. Water resistant when dry.

Part Number Description Price4-1029 1 QUART $11.98

Construction Adhesive

Liquid Nails, Interior/Exterior

NAIL POWER CONSTRUCTION

ADHESIVE Heavy Duty

A high performance adhesive for multi-purpose use.Recommended for use on paneling, drywall, plaster,decks, loose tile, plywood, treated lumber, concrete andbrick. Not recommended for polystyrene foam or panels. For interior or exterior use.

Part Number Description Price4-2017 10.2 FL. OZ. TUBE $2.98

Roof Cement

Wet or Dry, Plastic

ROOF CEMENT WET OR DRY

Plastic Use on metal roofs, asphalt roofs, and compositionroofs. Use around chimneys, flues, plumbing vents, etc.

Part Number Description Price4-1018 10.1 FL.OZ. TUBE $0.00

Constructive Adhesive

MAX BOND CONSTRUCTION

ADHESIVE Multi-Purpose

This premium grade multi-purpose interior/exterior construction adhesive is ideal for bonding paneling, wood, drywall, concrete, steel, aluminum, cork, polystyrene and urethane foams. Excellent for installing tub/shower wall kits. 10.6 fluid ounces per tube.


Boss Multi-Purpose

CONSTRUCTION ADHESIVE Multi-Purpose

by BOSS

Bonds most types of construction materials such as polystryene foam, paneling, marble, gypsum board, fiberglass panels, wood, paper and metal. An excellent waterproof adhesive for all types of tub/shower wallkits.

Part Number Description Price4-2016 10.3 FL. OZ. TUBE $5.98

Construction Adhesive

Liquid Nails, Exterior

LIQUID NAILS ADHESIVE

A fast bonding, superior quality, waterproof interior grade adhesive that stays flexible. Bridges gaps up to 3/8" and offers up to 10 minutes working time. Not for exterior use.

Part Number Description Price4-2018 10.5 FL.OZ TUBE $3.69



Fire Mortar

FIRE MORTAR A non-combustible silicate cement that can withstandextremely high heat. Formulated for repairing chimneys,fireplaces, wood stoves and appliances. Can be used onwood frame construction where non-combustible sealantis required. This product has excellent adhesion and setsto become rock hard when cured. Conforms to ASTME-136 and can withstand temperatures of up to 3000degree F. 10.1 fluid ounce cartridge.


Fiberglass Repair Kit

FIBERGLASS, PORCELAIN AND PLASTIC REPAIR KIT

Repairs holes up to 1” in diameter and cracks up to 5”long. May use on showers, tubs, sinks and toilets.Handling time 4 to 5 minutes, set time 20 minutes, curesin 24 hours. Holding strength of 1500 PSI. White & almond in same package.




Kool Seal, Blue Label

BLUE LABEL (SILVER) ROOF COATING by KOOL SEAL This original Blue Label Premium quality Kool Seal is so good that it has a 5-year factory product warranty, whenapplied according to manufacturer’s instructions. Blue Label Kool Seal has the finest aluminum pigments available, and has up to three times more pigment than most other brands on the market. These high grade aluminum pigmentsare microscopic flakes, when dispersed in asphalt, have the ability to migrate, over time, to the surface where theyreflect the sun’s heat. This reflect ability causes the home to be cooler, and prolongs the coating’s life. Cover approximately 80 to 100 Sq. Ft. per Gallon when applied as per instructions.

Part Number Description Price4-1055 5-GALLON $114.594-1057 1-GALLON $29.95

Kool Seal, Aluminum

ALUMINUM ROOF COATING by KOOL SEAL An economical good quality aluminum roof coating with less aluminum pigment than the other grade of Kool Seallisted on this page. Reinforced with non-asbestos fibers for a longer lasting roof life. Cover approximately 50 to 75 Sq. Ft. per Gallon when applied as per instructions.

Part Number Description Price4-1059 5-GALLON $79.98

Kool Seal, White Elastomeric

WHITE ELASTOMERIC ROOF COATING by KOOL SEAL This product reflects 90% or more of the suns rays saving up to 30% in energy costs. Forms a thick rubber-like blanket of protection against moisture and the elements. The durable acrylic elastomeric resin expands and contracts with your roof for a longer product life. Cured elastomeric film is mildew and algae resistant. Soap and water cleanup while wet.On smooth metal, coverage is approximately 100 sq. ft. per gallon when applying required two coats. Five (5) year limited product warranty when applied as per instructions.

Part Number Description Price1-GALLON NOT AVAILABLE

4-1065 5-GALLON $86.69

Kool Seal, Premium White Elastomeric

PREMIUM WHITE ELASTOMERIC ROOF COATING by KOOL SEAL Environmentally engineered premium white elastomeric kool seal saves up to 35% on energy costs while protectingagainst water damage. Higher solids content forms a thick rubber-like blanket for better coverage and protection. Expands and contracts with the temperature and is durable in all climates. Is mildew and algae resistant. Helps toabsorb sound. Soap and water clean-up while wet. On smooth metal, coverage is approximately 100 sq. ft. per gallon when applying required two coats. Ten (10) year limited product warranty when applied as per instructions.

Part Number Description Price4-1067 1-GALLON $30.474-1068 5-GALLON $129.00



Kool Seal, Patching Cement

PATCHING CEMENT White Acrylic KOOL SEAL

Formulated with durable acrylicresin and special reinforcingmaterials. Stops leaks on damp ordry surfaces. Long lasting, tough,flexible patch seals out water and ismildew resistant. Blends in onexisting white roofs and resistscracking, peeling and blistering.Soap and water cleanup while wet.

Part Number Description Price4-1060 QUART $8.984-1061 GALLON $23.37

Kool Seal, Storm Patch

STORM PATCH All Weather Rubberized

Cement KOOL SEAL

This all-weather premiumrubberized cement actuallydisplaces water from wet surfacesand creates a tight seal. Ideal forsealing around flashing,chimneys, vents, skylights, joints,gutters, pipes, and similar objects.Clean-up tools with kerosene,paint thinner or mineral spiritsimmediately after use.

Part Number Description Price4-1062 GALLON - BLACK $21.894-1063 TUBE - CLEAR $7.184-1064 TUBE - BLACK $3.29

Kool Seal, Glass Membrane

GLASS MEMBRANE Reinforcement Fabric

Excellent for repairing those troublesome seams orjoints that keep pulling apart. May be used withasphalt based or white roof coatings.

ll one gallon pails have .90 gallon of product.

Part Number Description Price4-2025 4" WIDE x 40 FT. LONG $6.79

Aldo Products, Great White

GREAT WHITE ELASTOMERIC ROOF COATING

by ALDO PRODUCTS CO.

Great White roof coating 100 is atechnologically advanced fire retardant,thrixotropic, acrylic elastomericcoating that has been formulated tohave exceptional adhesion to a varietyof substrates; such as primed wood, metal roofs, concrete and masonry. Itsunique formulation incorporateselastomeric acrylics resins, reinforcinglaminar pigments and othernonmigrating fire retardants to producea seamless, flexible, durable membranehaving exceptional weather ability, ultraviolet and fire resistance.Suggested coverage is 3-gallon per 100 square ft. or 15 mils thick.

Part Number Description Price4-1051 5-GALLON $89.00

Aldo Products, Butyl Seam Seal

BUTYL SEAM SEAL by

ALDO PRODUCTS CO.

Butyl seam seal, (ALDOSEAL 747), is a single component elastomer sealer specially formulated to provide a waterproof, weather resistant membrane with excellent permeability and ultraviolet protection. ALDOSEAL 747 offers good elongation and tensil strength to resist lateral movement and allow for expansion and contraction of the substrate. May apply acrylic base or asphalt base roof coating over this product within one hour of application. Color is white.

Part Number Description Price4-1048 GALLON $49.95



Silicone Caulk

SILICONE CAULKING

by BOSS “The Choice of the

Construction Industry” 100 % Silicone, 100% Acetoxy cure, 10.1 fl. oz. pertube.

Part Number Description Price4-2101 CLEAR $4.984-2102 WHITE $4.984-2103 ALUMINUM $4.984-2104 BLACK $4.984-2107 BRONZE $4.98

Acrylic Latex Caulk

ACRYLIC LATEX CAULKING


Construction Industry” Siliconized, Interior/Exterior use, Paintable after 60minutes of curing, 10.1 fl. oz. per tube.

Part Number Description Price4-2121 CLEAR $4.894-2122 WHITE $3.894-2123 ALMOND $3.894-2124 BROWN $3.894-2125 GRAY $3.89

Tub & Tile Caulk

Boss

Tub & Tile SILICONE CAULKING


Construction Industry” Mildew resistant, Non-yellowing, Paintable, 10.1 fl. oz.per tube.

Part Number Description Price4-2118 WHITE $5.794-2119 ALMOND $5.79

Silicone Caulk

SILICONE CAULKING

by BOSS

3 fl. oz. per tube.

Part Number Description Price4-1199 WHITE $2.984-2000 CLEAR $3.98

Tub & Tile Caulk

White Lightning

TUB & TILE CAULK

by White Lightning

Siliconized acrylic mildew and rust resistant. Excellent adhesion. Stays flexible.5.5 oz. tube.

Part Number Description Price5-1220 ALMOND $3.595-1221 WHITE $3.59



PEEL & SEAL An aluminum foil backed self-adhesive black butyl rubber flashing for quick,long lasting weather-proof seal.

Part Number Description Price4-2080 3" W x 33.5' L $17.894-2120 6" W x 33.5' L $25.98

SPEED MIXER This is a true mixer, not a paddle type stirrer.Entirely constructed of nickel-plated steel to resistcorrosion. For use with 3/8" or larger drill motor.Max. of 900 rpm. May be used to mix paint, roofcoatings and other similar density products. The small unit (2-3/8" head with 16" long x 3/8"diameter hex shaft) is ideal for one gallon pailswhile the large unit (4" diameter head with 24"long x 7/16" diameter hex shaft) works best in fivegallon pails.

Part Number Description Price4-2106 2-3/8" DIA. HEAD $6.594-2109 4" DIA. HEAD $11.19

SKELETON CAULKING GUN Made of heavy steel. 9" long for use with 10.1 oz. or similar sizetubes. The choice of the construction industry.


CAULK FINISHER Made of plastic, Bead size may be enlarged bytrimming end of finisher.


ROOF COATING BRUSH

This high quality inexpensive nylonbristle brush is ideal for applying roofcoatings.

Part Number Description Price4-2030 2-1/2" WIDE x 7" LONG $3.99

HANDLE for

ROOF COATING BRUSH

This heavy duty wood handle has a tapered end that fits snug into roof coating brush.

Part Number Description Price4-2031 1-1/8" DIA. x 54" LONG $4.49

BRUSH & HANDLE COMBINATION

Roof Coating

This combination roof coatingbrush and handle set has a 7” longx 2-1/2” wide wood brush with 2” long nylon bristles. The paintedscrew-in metal handle is 48” long x 7/8” diameter.


PAINT ROLLER KIT

Contains metal paint tray, 9"roller frame, and a 9" all-paint roller.


ROLLER FRAME

This 9 inch wire roller frame has formed grip threaded handle.




HANDLE for

ROLLER FRAME

This heavy duty wood handle has a threaded end that fitsinto the roller frame handle.

Part Number Description Price4-2038 15/16" DIA. x 60" LONG $4.98

Professional Grade

PAINT ROLLERS

These all purpose, 9", reusable rollers may be used with latex or oilbased paints. For smooth (1/4" nap) and medium (3/8" nap)surfaces.

Part Number Description Price4-2040 1/4" NAP $4.754-2046 3/8" NAP $5.46

Utility Grade

Part Number Description Price4-2041 1/4" NAP $3.654-2048 3/8" NAP $2.69

PAINT BRUSHES

Economy Grade White natural bristle with unfinished, sanded woodhandle.

Part Number Description Price4-2042 2" $0.894-2043 3" $1.29

Work

LEATHER PALM WORK GLOVES

Long lasting split cow hide palm, forefinger, fingertips & knuckle. Safety cuff for better protection. Striped cotton back & 100% cotton lining. One size fits all.


Jersey

JERSEY GLOVES Soft breathable, unlined, 100% cotton jersey. One size fits all.




Hex Head Screws, 1/4" Non-Slotted Hex Head

# 8, 1/2" thru 2" Long, Zinc Plated Steel

ZINC PLATED # 8 x 1/4" NON-SLOTTED

HEX WASHER HEAD

Part Number Description Price4-2500 #8 x 1/2" $0.024-2500M Box of 1000 $10.004-2510 #8 x 3/4" $0.0244-2510M Box of 1000 $13.004-2520 #8 x 1" $0.0244-2520M Box of 1000 $14.004-2530 #8 x 1-1/4" $0.034-2530D Box of 500 $8.004-2540 #8 x 1-1/2" $0.0364-2540D Box of 500 $9.004-2550 #8 x 2" $0.054-2550D Box of 500 $13.00

# 8, 1" thru 2" Long, Painted Heads

# 8 HEX HEAD SCREWS PAINTED HEADS

1/4 NON-SLOTTED HEAD

Part Number Description Price4-2552 #8 x 1" WHITE $0.0354-2552B #8 x 1" WHITE, 250 & up $0.024-2554 #8 x 1-1/2" WHITE $0.044-2554B #8 x 1-1/2" WHITE, 250 & up $0.034-2553 #8 x 2" WHITE $0.064-2553B #8 x 2" WHITE, 250 & up $0.0364-2555 #8 x 1" BROWN, $0.0354-2555B #8 x 1" BROWN, 250 & up $0.004-2556 #8 x 2" BROWN $0.064-2556B #8 x 2" BROWN, 250 & up $0.0384-2567 #8 x 1" ALMOND $0.0354-2567M #8 x 1" ALMOND, Box of 1000 $19.004-2568 #8 x 1" TAN $0.0354-2568M #8 x 1" TAN, Box of 1000 $19.004-2569 #8 x 1" CREAM $0.0354-2569M #8 x 1" CREAM, Box of 1000 $19.004-2570 #8 x 1" GRAY $0.0354-2570M #8 x 1" GRAY, Box of 1000 $19.004-2571 #8 x 1" BLACK $0.0354-2571M #8 x 1" BLACK, Box of 1000 $19.00

Countersunk Oval Head

COUNTER SUNK SCREWS

Part Number Description Price4-2579 Countersunk, Phillips, Stainless Steel.,

#6 x 1-1/4"$1.98

4-2581 Countersunk, Clutch, Nickel Plated., #5 x1-1/2"

$0.00

4-2582 Countersunk, Square, Zinc Plated., #6 x1-1/4"

$0.015

4-2583 Countersunk, Phillips, Zinc Plated., #8 x1"

$0.04

Flat Head Hinge Screws

FLAT HEAD SCREWS

Part Number Description Price4-2585 Flat, Countersunk, Phillips, Brass Pltd.,

#7 x 1"$0.05

4-2586 Flat, Countersunk, Phillips, Brass Pltd.,#7 x 1-1/2"

$0.07

4-2584 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 1"

$0.05

4-2587 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 1-1/2"

$0.07

4-2588 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 3"

$0.10

Round Washer Head

ROUND WASHER HEAD SCREWS

Part Number Description Price4-2591 Zinc Plated Steel, use #2 square insert

bit., #8 x 1"$0.00

4-2592 Zinc Plated Steel, use #2 square insertbit. Deep thread., #8 x 3"

$0.05

4-2592B Zinc Plated Steel, use #2 square insertbit. Deep thread., #8 x 3", 250 & up

$0.04

4-2595 Zinc Plated Steel, use #2 square insertbit. Deep thread., #10 x 5"

$0.12

4-2595B Zinc Plated Steel, use #2 square insertbit. Deep thread., #10 x 5", 250 & up

$0.10



Flat Countersunk Square Head

Plain Steel

FLAT COUNTERSUNK SQUARE HEAD SCREWS

Plain Steel

Part Number Description Price4-2590 8 x 2" $0.044-2590B 500 & up $0.0254-2600 #8 x 3" $0.054-2600B 250 & up $0.0354-2601 #8 x 4" $0.054-2601B 250 & up $0.044-2602 #10 x 5" $0.094-2602B 200 & up $0.07

Hot Dip Galvanized

FLAT COUNTERSUNK SQUARE HEAD DEEP THREAD

Hot Dip Galvanized

Part Number Description Price4-2610 #8 x 2-1/2" $0.084-2610B 250 & up $0.064-2611 #8 x 3" $0.094-2611B 250 & up $0.07

Hex Head Screws, 1/4" Non-Slotted Hex Head

# 8, 3/4" Long, Aluminum

ALUMINUM # 8 x 1/4" NON-SLOTTED

HEX WASHER HEAD

Part Number Description Price4-2630 #8 x 3/4" $0.034-2630M Box of 1000 $32.00

# 9, 3/4" & 1" Long, Aluminum

ALUMINUM #9 SIZE

1/4" SLOTTED HEX WASHER HEAD

This #9 screw is ideal for replacing the normal size (#8) screws in mobile homes and RV’s. Thelarger body size fits tighter where a #8 screw was previously installed. The extra large washer head covers up ugly rust stains. Also, the washer headis designed to help prevent screw from backing-out over time.

Part Number Description Price4-2661 #9 x 3/4" $0.0394-2661M Box of 1000 $38.004-2662 #9 x 1" $0.0464-2662M Box of 1000 $42.00

# 8, 1/2" Long, Self-Drilling, Zinc Plated Steel

ZINC PLATED STEEL SELF-DRILLING

# 8 x 1/4" NON-SLOTTED HEX WASHER HEAD

Part Number Description Price4-2560 #8 x 1/2" $0.024-2560M Box of 1000 $14.00

# 10, 1/2" Long, Zinc Plated

ZINC PLATED #10

5/16" NON-SLOTTED HEX HEAD

Part Number Description Price4-2565 #10 x 1/2" $0.03

Wood Screws

WOOD SCREWS SOLID BRASS

Part Number Description Price4-2598 Wood Screw, Solid Brass, Flat,

Countersunk Head, Phillips. Excellentfor mounting toilet flanges., #14 x 1-1/4",Package of 8.

$2.19



LAG SCREWS 9/16" Hex Head

Raw Steel Packaged with fender washers

Part Number Description Price4-2690 3/8" dia. x 3", 50/pkg $0.284-2691 3/8" dia. x 5", 50/pkg $0.354-2692 3/8" dia. x 6", 25/pkg $0.394-2694 3/8" dia. x 8", 25/pkg $0.56

Spiral Drive, Round Head

SPIRAL DRIVE NAILS ROUND HEAD

PLATED STEEL

1-1/4" LONG 50 PER PKG

Part Number Description Price4-2701 NICKEL PLATED #4 $1.394-2702 BRASS PLATED #4 $1.394-2703 NICKEL PLATED #6 $9.98

SCREW CAP PLASTIC

9/16” outside diameter plastic screw caps willaccommodate #6 thru #10 screw withcountersunk head. Priced per package of 25.

Part Number Description Price4-2720 WHITE $4.984-2721 BLACK $4.98

FENDER WASHER Flat Zinc Plated Steel

3/8" diameter hole, 1" outside dimensions,1/16" thick. 3550 per case. 50 lbs per case.Priced per each.

50 per bag


Green Cleaner

GREEN CLEANER Concentrate

Removes grease and grime when used at full strength, yet still effective for glass and crystal when diluted. Non-toxic, non-corrosive and biodegradable.

Part Number Description Price4-2059 22 oz. spray $4.98

Black Streak Remover

BLACK STREAK REMOVER Use this tough 100% spray to quickly and easily remove even the most stubborn black streaks. It’s strong enough to clean, but will not harm the paint.

Part Number Description Price4-2063 32 oz. spray $5.494-2064 1 gal. $18.98

Trailer Glitter

TRAILER GLITTER Remove road grease, dirt and grime in minutes with this concentrate cleaner. Adds sparkle and shine and protects any painted surface. Also great for removing mildew and stains.

Part Number Description Price4-2065 32 oz. $4.984-2066 1 gal. $14.98



Rope Caulk

ROPE CAULK Press in place to seal cracks and stop drafts.Will not harden or dry out. One roll coversapproximately 30 ft. Woodstone color.


Butyl Tape

BUTYL TAPE Sealant

Premium quality, permanent resilienceand elongation characteristics. Excellentfor sealing problem areas. Great for usewhen installing doors & windows. Gray in color.

Part Number Description Price4-2021 1/8" x 3/4" x 30 ft. $4.39

Duct Tape

Polybutylene, UL181

DUCT TAPE Polybutylene

Code approved UL 181B-FX For use on vinyl and foil backed flexible ductand duct wrap. 3.0 mil thick, has cold weather (-35deg. F) acrylic adhesive. 2" x 120 yds.

Part Number Description Price4-2071 BLACK $10.494-2072 METALLIC $10.49

Coated Cloth

DUCT TAPE Coated Cloth

Super sticky, conforms easily to items beingtaped, super performance. 10 MIL thickness.Gray color.

Part Number Description Price4-2075 2" x 60 yds. $6.98

Coated Cloth, UL181

DUCT TAPE Coated Cloth

Code Approved UL 181B-FX For use on vinyl and foil backed flexible ductand duct wrap. 2"x 60 yds.

Part Number Description Price4-2074 BLACK $15.984-2076 SILVER $15.98

High Tack Tape

HIGH TACK TAPE

The best tape on the market for repairing and patching vapor barrier under manufactured homes. Firstline No. 620. Black.


Duct Tape

Aluminum, UL181

ALUMINUM FOIL DUCT TAPE

Code Approved UL 181A-P For use on foil faced products such as duct board, duct wrap, and flexible duct.

Part Number Description Price4-2078 2-1/2" x 60 yds. $21.98

Duct Tape

Aluminum Foil

ALUMINUM FOIL TAPE

2 MIL aluminum foil has easy release liner.


Duct Tape

Aluminum with Heavy Butyl

ALUMINUM FOIL DUCT TAPE

with HEAVY BUTYL ADHESIVE

2-mil dead soft aluminum foil, heavy duty, all-weather duct tape with 43-mil butyl rubber adhesive. Excellent for repairing mobile home duct work. Has 20 lbs. per inch tinsel strength. Has easy release liner.

Part Number Description Price4-2080 3" x 30 ft. $17.89



Electrical Tape

ELECTRICAL TAPE Vinyl

UL approved, flame retardant 7 MIL tape suitablefor 600 volts or less and not more that 176 deg. F.

Part Number Description Price4-2081 3/4" x 60 ft., BLACK, Pro Grade $1.984-2082 3/4" x 66 ft., RED $1.494-2083 3/4" x 60 ft., BLACK, Econo Grade $0.98

Duct

DUCT TAPE INSULATION TAPEFoil Scrim Kraft (FSK) Tape

Non-tearable, diamond patterned 7-mil foil backing with an aggressive (AWF)all weather formula rubber adhesive.This superior adhesive system is perfectin application temperatures rangingfrom -25 deg F to + 250 deg F. Thistape is a must when installing orrepairing foil-backed duct insulation.Easy release liner. UL 723characteristics. Rolls are silver in color.


Carpet Tape

CARPET TAPE HOT MELT

Professional Grade This quick lock seaming tape is heat activatedfor bonding carpet seams.


Cork Tape

CORK INSULATION TAPE

Part Number Description Price4-2087 1/8" x 2" x 30 ft. $11.98



Hex

HEX DRIVERS

Part Number Description Price4-1079 3/16" $4.294-1081 5/16" $4.294-1083 3/8" $4.294-1085 7/16" $4.294-1084 1/2" $4.29

Square

SQUARE DRIVER

Part Number Description Price4-3211 #1 SQUARE $4.194-3212 #2 SQUARE $4.694-3113 #3 SQUARE $4.98

Clutch

CLUTCH DRIVERS

Part Number Description Price4-3220 5/32" CLUTCH $4.98

SCREWDRIVER REVERSIBLE BLADES

4 IN 1 Has Phillips #1 and Phillips #2, slotted 3/16" and 5/16"reversible blades.


6-IN-1 DRIVER KIT

Includes:

#1 SQUARE #2 SQUARE #2 PHILLIPS

5/32" CLUTCH 3/16" SLOTTED

1/4" HEX

BITS STORE IN HANDLE.


MEGA-MAGNETIC BIT HOLDERS

By IVY CLASSIC

These bit holders have twomagnets with forty times theholding power of other bit holders.One magnet holds the bit in placewhile the other magnet holds thefastner in place. The ¼” hex driveis made of stainless steel. The twenty-three inch long ¼” has a non-rotating outer sleeve for safer steadier operation.

Part Number Description Price4-3270 3" LONG $7.194-3274 23" LONG $17.69



Square

INSERT BITS (SQUARE)

One inch long, 1/4" hex drive.

Part Number Description Price4-3228 #0 SQUARE $0.494-3230 #1 SQUARE $0.494-3232 #2 SQUARE $0.494-3234 #3 SQUARE $0.89

Phillips

INSERTS BITS (PHILLIPS)

One inch long,1/4" hex drive.

Part Number Description Price4-3235 #1 PHILLIPS $0.494-3236 #2 PHILLIPS $0.49

Slotted

INSERT BITS (SLOTTED)


Part Number Description Price4-3238 #2 SLOTTED $0.49

Clutch

INSERT BITS (CLUTCH)


Part Number Description Price4-3240 5/32" CLUTCH $1.69

Square

POWER BITS (SQUARE)

Part Number Description Price4-3241 #1 SQUARE x 2" $0.984-3242 #2 SQUARE x 2" $1.294-3247 #2 SQUARE x 4" $1.49

Phillips

POWER BITS (PHILLIPS)

Part Number Description Price4-3243 #1 x 2" PHILLIPS $0.004-3244 #2 x 2" PHILLIPS $0.984-3249 #2 x 3-1/2" PHILLIPS $1.254-3245 #3 x 3-1/2"PHILLIPS $1.494-3258 #2 x 6" PHILLIPS $2.39

Slotted

POWER BIT (SLOTTED)

Part Number Description Price4-3246 # 8-10 x 2" SLOTTED $1.29

Clutch

POWER BIT (CLUTCH)

Part Number Description Price4-3248 5/32" x 2" CLUTCH $2.98



Magnetic Socket

Power Bits

POWER BITS MAGNETIC

SOCKET

1/4" HEX DRIVE

Part Number Description Price4-3250 1/4"HEX x 2"LONG (Tapered Socket

End)$3.98

4-3255 1/4"HEX x 4"LONG $8.394-3256 1/4"HEX x 6"LONG $6.894-3251 5/16"HEX x 2"LONG $2.984-3252 5/16"HEX x 4"LONG $7.294-3253 5/16"HEX x 6"LONG $7.98

Insert Bit Holder

INSERT BIT HOLDER (MAGNETIC)

Holds all 1/4" shank bits.


Magnetic Socket

MAGNETIC SOCKET

1/4" square drive.

Part Number Description Price4-3229 1/4" HEX $4.984-3226 5/16" HEX $4.98

Socket Adapter

SOCKET ADAPTER

1/4" hex x 1/4" square. 1-3/8 inches long.




4-Stop Positions

UTILITY KNIFE

This all metal knife has 4-stop positions for blade, with bladestorage in handle. Comes with one blade.


Rapid Reload

RAPID RELOAD UTILITY KNIFE “Ivy Classic Brand”

The Power Pro Grip handle is designed for comfort & balance.Five blade rapid reload cartridge fits into handle. Simply press thered button to release the blade and slide a new one into place. Usesstandard utility blades. Comes with 6 blades.

Part Number Description Price4-3315 KNIFE WITH 6-BLADES $7.984-3316 RAPID RELOAD CARTRIDGE,

5-BLADES$1.19

Retractable W/ Snap-Off Blade

UTILITY KNIFE Retractable with snap-off blade and safety lock, easy bladereplacement. 3/4" wide blade.


Double End Hook Blade

HOOK BLADE FOR

UTILITY KNIVES This heavy duty deep throat hook blade fits most popular utility knives. 5 blades per package.


Heavy Duty, 5 Blades Per Package

UTILITY KNIFE BLADES “Ivy Classic Brand”

Heavy duty blades for industrial and home use. For general cutting, trimming, and scraping. Made of high carbon steel. 5 blades per package.


Heavy Duty, 100 Pack Dispenser

UTILITY KNIFE BLADES by

Ivy Classic This 100 pack dispenser is handy and economical for volume users of heavy duty blades. Made of high carbon steel.

Part Number Description Price4-3323 100 PER PACKAGE $16.98

Single End Hook Blade

HOOK BLADE by

STANLEY For cutting vinyl or linoleum floor coverings, roofing and similarmaterials. For use with fixed blade knives only. # 11-980


Fixed Blade Style

UTILITY KNIFE by STANLEY

Fixed Blade Style

For use with all fixed style blades. Contractor grade.




HACKSAW (ADJUSTABLE)

Part Number Description Price4-3325 ECONOMY $6.984-3326 DELUXE GRADE $10.98

HACKSAW BLADES High quality blades made of high carbon steel. 24 teeth per inch.

Part Number Description Price4-3327 10" $1.684-3328 12" $1.77

MEASURING TAPE This 25 ft. tape has vivid black numbers on ayellow blade with red indicators for every foot.Triple riveted end hook. Deluxe chrome tensionbelt clip. Bright neon color makes it harder tomisplace.


AVIATION SNIPS “Ivy Classic Brand”

Cuts straight to wide curves, left or right. The non-slip serratedjaws cut up to 18 gauge low carbon cold rolled steel. Self-opening jaws.


TORPEDO LEVEL Has level, plumb, and 45 deg. bubbles. 9" long. Has strongmagnet to hold level in position.


WIRE BRUSH Shoe handle style, tempered andgalvanized bristles. Overall length10".


PUTTY KNIFE 1-1/4" wide steel blade with plastic handle. Stiff blade.




Poly, PVC & Pex Pipe

TUBING CUTTER “LiL Nipper”

Cuts poly, PVC and pex tubing, andrubber hose up to 1-5/8" O.D. Lightweight, safe and tough. Stainless steelblade.

Part Number Description Price4-3500 TUBING CUTTER $12.004-3502 BLADE ONLY, “LI’L NIPPER”, 2/PKG $8.984-3504 BLADE ONLY, “IVY CLASSIC”, 1/PKG $4.98

PVC Pipe

TUBING CUTTER FOR

PVC PIPE Cuts PVC pipe up to 1-5/8" O.D. Heavy duty metal construction,replaceable stainless steel blade.

Part Number Description Price4-3501 TUBE CUTTER $15.984-3503 BLADE ONLY $7.49

SAND CLOTH 120 GRIT

1-1/2" WIDE

Part Number Description Price4-3506 2 YDS $1.994-3507 10 YDS $5.49

SOLDER 100% Lead Free

Lower melting point than 95/5, wide workingrange similar to 50/50. 1 lb. spool.


SOLDERING PASTE

NOKORODE Works on all solder alloys including 95-5 and all lead free solders.


WD-40

WD-40 Spray Lubricant

with Smart Straw Feature

Stops squeaks, loosens rusted parts, frees sticky mechanisms and protects metal. New smart straw features a permanently attached straw that sprays two ways. Simply flip it up for a precision stream and down for a regular spray. 11ounce can.


Liquid Wrench

LIQUID WRENCH Spray Lubricant

with Teflon This non-flammable super lubricant stops squeaks, loosens rust and penetrates. 11 oz. can.


Silicone

SILICONE Spray Lubricant

Stops squeaks, waterproofs, rust proofs and lubricates. Compatible with all metals, rubber and wood. 12 oz. can.




HYDRAULIC AXLE JACKS

Gives Long, Trouble-Free

Performance

MULTI-POSITION DESIGNCan Be Used At Any Angle

Lifetime Limited Warranty

Unlike many other jacks on the market, these jacks can be rebuilt, should they fail to operate. We stock rebuild kits and several other parts.

Part Number Description Price4-76412 12 TON, Standard Height, Fully

Extended 18-3/4"$139.00

4-76512 12 TON, Low Height, Fully Extended13-3/16"

$139.00

4-76520 20 TON, Standard Height, FullyExtended 10-1/16"

$198.00

NORCO JACK REBUILD KITS

Rebuild kit includes: O-rings, filler plug, seals, chrome check ballsand pump plunger.

Part Number Description Price4-5000 20 TON $29.984-5001 12 TON STANDARD $29.95

REPLACEMENT PINS FOR NORCO JACKS

Comes with e-ring Part Number Description Price4-5002 PIN, LINK, 5/16"dia. x 15/16" long,

(Lever linkage to jack body)$1.29

4-5003 PIN, LINK, 5/16" dia. x 1" long, (Leverlinkage to pump plunger)

$1.29

REPLACEMENT LIMIT PIN

NORCO JACKS

Part Number Description Price4-5006 9/32" diameter x 1-3/4" long, (# 6 on

exploded parts diagram)$1.98

RUBBER OIL FILL PLUG


HARDWOOD BOARDS

8" x 16" x 1" 10 PER BUNDLE

600 PALLET


HARDWOOD WEDGES

1" x 4" x 10" 50 PER BUNDLE

5,000 PALLET




FOUNDATION PADS ABS

Approved for use in NC as footers.They are lightweight, easy toinstall, will not crack or split andsaves on labor cost. Limited lifetime warranty.

Part Number Description Price4-5016 16" x 16" x 3/4" - 20 per Bundle $5.394-5018 20" x 20" x 3/4" - 10 per Bundle $8.98

FOUNDATION PAD Round

This round pad is ideal for use asdecking footer where concrete footersare not required. Pads are made fromrecycled automobile tires and selectresins. Will not rot or deteriorate and islight weight, only 3 lbs. each. 15-3/4” diameter x 1-1/2” thick.


.030" Narrow

STAPLES by

DUO-FAST

.030" NARROW CROWN STAPLES

5000 PER BOX

Part Number Description Price4-3416 1/2" - Natural $14.004-3418 9/16" - Natural $14.504-3416-4 1/2" - Tan $17.794-3418-4 9/16" - Tan $19.584-3416-1 1/2" - Brown $17.794-3416-3 1/2" - White $17.794-3418-3 9/16" - White $19.58

.050" Narrow

STAPLES by

DUO-FAST

.050" NARROW CROWN STAPLES

5000 PER BOX

Part Number Description Price4-5418 9/16" - Natural $12.3945418-3 9/16" - White $19.58

POP RIVETS Aluminum

25 Per Package

Part Number Description Price4-5430 1/8" DIAMETER x 3/8" LONG, (Has 1/4"

maximum grip)$1.25

4-5431 3/16" DIAMETER x 11/16" LONG, (Has1/2" maximum grip)

$2.29

“S” HOOK This 1-1/2" long open type S-hook is made of heavy gauge zinc coated steel. Maximum weight limit is 40 pounds.


Gutter Screws With 5" Ferrules

GUTTER SCREWS With

5” Ferrules These 7” long gutter screwsand 5” ferrules are made foruse with 5” gutter. Perfect forreplacing spikes that havepopped out. Use originalinstallation hole on existinginstallations. Comes with ¼”drive x #2 square bit for installing screws. There are10 screws and ferrules perpackage. We stock white only.


Zip-it Anchor

ZIP-IT ANCHOR This #8 self-drilling plastic anchor is ideal forhanging heavy items on drywall board. May use with #6 or #8 screw. Inside of head is cut for Philips or slotted screwdriver. Anchors are white or natural color. Packaged 10 per plastic bag.




REGULATOR LP GAS

LOW PRESSURE ONLY

140,000 BTUH CAPACITY 1/4" F.P.T. INLET

3/8" F.P.T. OUTLET


TANK VALVE LP GAS

STANDARD VALVE POL x 3/4" #14 NGT

Part Number Description Price4-6030 TANKS UP TO 40 LBS $9.984-6032 FOR 100 LB TANKS $9.98

REGULATOR TEE Inverted Type

1/4" O.D. TUBE by 1/4" M.P.T.


TAILPIECE ASSEMBLY

FOR

LP GAS REGULATOR POL x 1/4" M.P.T.


PIGTAILS - LP GAS

POL TO 1/4" INVERTED FLARE COPPER TUBING WITH

BRASS FITTINGS

Part Number Description Price4-6070 15" LONG $7.694-6071 20" LONG $7.79

JIG SAW BLADES Assorted 5-Pack

U-shank fits Black & Decker, Skil, Craftsman, Milwaukee, DeWalt,Makita, Ryobie and Porter Cable saws.Three blades are for wood cutting; one 4” blade with 10 tpi for clean smoothcuts, one 4” blade with 6 tpi for faststraight cuts and one wood cuttingscroll blade 2-3/4” with 12 tpi. Two blades for metal cutting; one 2-3/4” blade with 24 tpi for metal under 1/8”thick and one blade 2-3/4” with 14 tpi for metal over 1/8” thick. All bladesare made of high carbon steel withcobalt cutting edges.


RECIPROCATING SAW BLADE

IVY CLASSIC BRAND

This 6” long metal cutting blade has 18TPI (teeth per inch). Cuts metal 18gauge to 1/8” thick. Fits all 1/2” shankreciprocating saws. Has bi-metal cobalt cutting edge with 65-67 Rockwell hardness.


RECIPROCATING SAW BLADE

IVY CLASSIC BRAND

This 6” long wood, nail embedded wood and composition materialscutting blade has 6 TPI (teeth per inch). Fits all 1/2” shank reciprocating saws.Has bi-metal cobalt cutting edge with65-67 Rockwell hardness.




HOLE SAW The original patented high speed hole sawwith handy built-in arbor. Guaranteed to cutwood, plastic, or any machineable metal. Usewith pilot drill bit shown this page.

Part Number Description Price4-7000 1" DIAMETER $9.984-7001 2-1/8" DIAMETER $15.89

INSTALLATION KIT DOOR LOCKS WOOD DOORS

Door lock installation kit for use on wood doors 1-3/8” or 1-3/4” thick. Comes with adjustable molded plastic guide template foreasy and exact drilling. Use template for 2-3/8” and 2-3/4” backsets. Has 1” and 2-3/4” diameter wood hole saws with arbor &pilot drill bit that fits both hole saws. May use with entry locksand/or deadbolt locks. Instructions come with installation kit.


INSTALLATION KIT DOOR LOCKS

BI-METAL DOORS

Bi-metal installation kit for metal or wood doors 1-3/8” or 1-3/4” thick. Comes with adjustable molded plastic guide template foreasy and exact drilling. Use template for 2-3/8” and 2-3/4” backsets. Includes 1” and 2-1/8” diameter bi-metal hole saws witharbor & pilot drill bit that fits both hole saws. May use with entrylocks and/or deadbolt locks. Instructions come with installation kit.


PILOT BIT FOR HOLE SAW 1/4" diameter bit is made of high speed steel.


SCRAPER Razor Blade Retractable

Scrapes and cleans paint from glass, tile and metal. Comes withone high carbon steel .009" thick single edge blade.


RAZOR BLADES Single Edge

High Carbon Steel .009" thick industrial quality high carbon steel single edge blades are individually wrapped. Comes 10 to a package.


HUB PULLER Blower Wheel Fan

Blade This heavy duty hub puller isideal for pulling hub styleblower wheels and fan blades.Comes complete with four pullfingers and shaft alignmenttool. Fine threads provide foradditional torque and pullingpower.




Copper Tubing

TUBE CUTTER

ECONOMY GRADE ALL METAL BODY

Cuts from 1/8" to 1-1/8" tubing size. Part Number Price4-3348 $7.98

Copper Tubing, Midget With Rollers

TUBE CUTTER MIDGET

With Rollers

Cuts from 1/8" to 7/8" O.D. tubing.


TENSIONING TOOL

For Nylon Ties

Fits all standard and heavy duty ties.Provides proper tightness and trimsexcess materials flush.


Pressure Test Kit

PRESSURE TEST KIT

Comes with two steel-case pressuregauges, one is 0-30 psi, the other 0-100 psi. Gauges have unbreakable plasticfaces, 1/4"brass m.p.t. connection. Brassmanifold has 3/4" f.p.t. connection oneend with brass air valve on other end.For testing water piping, sewer systemand/or gas piping.


Water Pressure Test Gauge

PRESSURE TEST KIT

This water pressure test gauge has a metal casing with a unbreakable plastic face. Readings from 0 to 300 PSI. Has a 3/4" female hose adapter made of brass.


CARPENTERS PENCIL

Made of wood, has gray lead, 7 inches long.


MARKING FLAGS

Flag is made of 2.5" x 3.5" orange plastic attached to a 21" long steel shaft.

Sold 100 per bundle.


ELEMENT WRENCH (Heavy Duty)

Fits all screw-in water heater elements. Fits all 1-1/2 hex nuts. Heavy duty zinc plated steel.




Date post:	06-Feb-2018
Category:	Documents
Upload:	phungtruc
View:	221 times
Download:	1 times

36 DOUBLE HEAD ANCHOR - Triad Mobile Home Supplytriadmobilehomesupply.com/catalog/section_07.pdf ·...

Documents