NU-CONCEPT ANCHORS WITH STABILIZER CAP
30" DOUBLE HEAD ANCHOR
HAS TWO 4" SHARPENED HELIX
Suitable for use in class 2 & 3 soil
The 6"diameter swivel stabilizer cap is approved for use on anyand all Minute Man anchors. Simply slide cap over anchor headand install included bolt, then continue to screw anchor into theground until the flat surface of the cap is at or below ground level.
Part Number Description Price3-3476 3/4" DIA. SHAFT $7.983-3476-96 96 to 199 $7.183-3476-200 200 & up $7.183-3479 7/8" DIA. SHAFT $10.32
STABILIZER CAP, See 3-3555
36" DOUBLE HEAD ANCHOR
HAS ONE 6" AND ONE 4" SHARPENED HELIX 3/4" DIA. SHAFT
Suitable for class 2, 3 & 4 soil
Part Number Price3-3477 $9.69
50" DOUBLE HEAD ANCHOR
HAS ONE 6" SHARPENED HELIX 5/8" DIA. SHAFT
Suitable for class 2, 3 & 4 soil
Part Number Price3-3480 $8.45
E-Z ONE-STEP STABILIZED ANCHORING
Combines anchor & stabilizer as one unit. Reduces installationtime by 50% over separate anchor & separate plate installation.
30 inch long, 3/4 inch diameter shaft, double head with two 4
inch diameter sharpened disc.
Suitable for use in class 2 & 3 soil
Part Number Price3-3481 $10.98
DOUBLE HEAD BARBED ROCK ANCHOR
This anchor is designed to be driven into a 1-1/4" Dia. hole drilled 8" deep into solid rock.
24 Inches long, 23/32 inch dia shaft with double head
Head slides down over anchor shaft for ease of driving anchor into rock.
Part Number Price3-3492 $11.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 144
DOUBLE HEAD ROCK CROSS ANCHOR
Comes with two 36" x 3/4" rods.
Must be used in solid rock.
Part Number Price3-3482 $14.78
CONCRETE ANCHOR “L” Shaped
For use when pouring concrete.
Part Number Description Price3-3498 PAINTED STEEL $3.983-3498G GAL. STEEL $5.89
DOUBLE HEAD PATIO ANCHOR
For use in existing concrete. Split strap bolts are soldseparately. Made of heavy gauge painted steel.Comes with expansion bolt.
Part Number Price3-3497 $3.89
FRAME TIE WITH HOOK
Attach frame clamp (hook) on inside top flange ofhome I-beam. Bring galvanized strap between floor and I-beam. Go around I-beam one completeturn, pull strap tight and attach to split bolt onanchor tensioning head.
Part Number Description Price3-3488 7 FT. FRAME TIE $3.263-3488-96 96 & UP $2.943-3489 10 FT. FRAME TIE $3.983-3489-96 96 & UP $3.59
FRAME TIE WITH BUCKLE
Has 10 ft. long strap
Part Number Description Price3-3487 1 THRU 95 $3.953-3487-96 96 & UP $3.56
LOCKING FRAME CLAMP II
MMA-33 ASSEMBLED UNIT Shown as an assembled unit, but sold separately. Clamp comeswith a plated grade-5 bolt & nut. Strap comes with attached pivot clip with bolt hole to attach to frame clamp.
Part Number Description Price3-3473 10 FT. STRAP & CLIP $4.193-3473-96 96 & UP $3.773-3474 CLAMP ONLY $2.683-3474-96 96 & UP $2.42
CORNER TIE With Galvanized Strap
This galvanized steel pivot clip is bent at a 45 degree angle with one 1/2" diameter hole. The attached galvanized steel strap is 7 feet long. Designed mainly for use with longitudinal frame clamp # 3-3475.
Part Number Description Price3-3472 1 THRU 95 $3.263-3472-96 96 & UP $2.94
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 145
LONGITUDINAL FRAME CLAMP We stock the four bolt type for use in wind zone I. Consists oftwo top plates, one bottom plate and four plated grade-5 bolts. Clamp mounts on bottom of I-Beam as shown. Note: Use strap & pivot clip # 3-3472
Part Number Description Price3-3475 1 THRU 95 $8.293-3475-96 96 & UP $7.46
BUCKLE
Made of heavy galvanized steel.
Part Number Description Price3-3484 SINGLE SLOT $0.643-3485 DOUBLE SLOT $0.49
CRIMPS
For use with steel strapping.
Part Number Price3-3486 $0.24
STRAPPING 1-1/4" x .035 thick galvanized steelstrap. Stamped as per ANSI code & Staterequirements.
Part Number Description Price3-3494 37 ft. $10.983-3495 600 ft. $149.00
GALVANIZED STRAPPING
This strapping is used to tie modular homesto the foundation sill plate. Twenty -four (24) gauge galvanized steel. Two inches(2") wide x sixteen inches (16") long.
Part Number Price3-3496 $0.99
ANCHOR BOLT WITH NUT Plated steel split bolt and nut for use with strap.
Part Number Price3-3483 $0.79
ROOF BRACKET We stock both galvanized steel and aluminum roof brackets. Both type are made of heavy gauge material to withstand high stress levels exerted by high winds.
Part Number Description Price3-3490 GALVANIZED STEEL $5.593-3491 ALUMINUM $5.98
FRAME TIE HOOK For use with tie down strapping. Made of heavy gauge galvanized steel.
Part Number Price3-3499 $0.98
CARRIAGE BOLT
Grade 5 plated steel bolt and nut. Part Number Description Price3-3469 1/2" x 1-1/4" $0.69
ADJUSTABLE OUTRIGGERS Eliminates perimeter blocking, problems with anchor spacing, andinterference with skirting. Outer wall settling is greatly reduced.
Easy to install and are tested & approved.
Part Number Description Price3-3550 FOR 14 FT. WIDE HOMES $14.493-3551 FOR 16 FT. WIDE HOMES $17.35
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 146
STABILIZER CAP Designed for attaching to the head of Nu-Concept Minute Man anchors. Used instead ofthe drive-in style stabilizing plate. Cap is 6"dia. and 1"deep. Comes with bolt to secure toanchor. Comes 16 in a box.
Part Number Description Price3-3555 1 thru 95 $4.193-3555-96 96 to 200 $4.073-3555-200 200 & up $3.95
STABILIZER for ANCHORS This stabilizer has been designed to meet theN.C. state code effective Jan. 15, 1991. Wastested and approved for use without the useof a U-bolt to hold the anchor against thestabilizer plate. Made of heavy gage paintedsteel.
Part Number Price3-3478 $6.49
ANCHOR FLANGE Concrete Dry Set
This dry set anchor flange is used insteadof using the pier pad pan. Longitudinal orlateral brace tubes may be connected tothis device. Comes with one 1/2" x 1-1/2" long carriage bolt and two 5/8" x 3" longshield anchors for concrete. MMCAF 24 per box.
Part Number Price3-3575 $8.69
ANCHORING KIT for UTILITY BUILDINGS This system is designed for small to medium size storage/utilitybuildings. Comes with four painted eye anchors that are 30” with 1/2" diameter shaft and has one 3" diameter sharpened helix. Has50 feet of 6-strand-20 gauge galvanized steel cable and four zinccoated u-bolt clamps with nuts. Kit weighs 8 pounds.
Part Number Price3-3578 $38.00
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 147
Minute Man, Brace System for Soil
THE MINUTE MAN FOUNDATION SYSTEM EXCEEDS REQUIREMENTS
FOR ALL WIND ZONES
Eliminates or reduces most anchors and hardware, saving time and money
ZONE I, II & III LONGITUDINAL AND LATERAL BRACING SYSTEMS FOR SOIL INSTALLATIONS
Ground anchors may not be required on double wide homes.Marriage wall and perimeter wall anchors must be used when calledfor by home manufacturer. 3,150 lb. working load ground anchorswith stabilizers and frame ties are required on 4 corners of all single
wide homes. Systems must be as equally spaced as possible and no more than 10 ft. from the end of the home. Triple wide homes and tagunits require two additional systems.
Part Number Description Price3-3580 PIER PAD, 20" x 20", GALVANIZED STEEL (MMSPP), (4 ea. 16" long drive pins and
2 ea. 1/2" x 2-1/2" long bolts/nuts)$42.76
3-3584 LATERAL BRACE TUBE KIT with hardware, 60" to 96", (EACH package contains: 2ea. brace tubes, 2 ea. 2" x 7-3/4" lateral clamps, 2 ea. 1-5/8" x 2" tube clamp, 4 ea.1/2" x 2-1/2" bolt/nut, 4 ea. 1/2" x 1-3/8" washers, 2 ea. 1/2" x 1-1/4" bolt/nut, 8 ea. 1/4"x 3/4" self drilling screws). Two Lateral brace tubes with hardware per pkg., pricedseparately.
$48.89
3-3585 LATERAL BRACE TUBE HARDWARE KIT (Each hardware kit contains enoughproduct to install two tubes)
$18.98
3-3586 LONGITUDINAL BRACE TUBE, 39" LONG With Hardware $24.983-3587 LONGITUDINAL BRACE TUBE, 44" LONG With Hardware $27.003-3588 LONGITUDINAL BRACE TUBE, 53" LONG With Hardware $29.663-3589 LONGITUDINAL BRACE TUBE, 65" LONG With Hardware (EACH package contains:
2 ea. Brace tubes, 2 ea. Preassembled beam clips, 4 ea. 3-3/4" x 2-3/4" top coverattachment clips, 8 ea. 1/2" x 1-1/4" bolt/nut.) Two longitudinal brace tubes withhardware per pkg, priced separately.
$32.79
3-3592 LONGITUDINAL BRACE TUBE HARDWARE KIT (MMLBC) (EACH hardware kitcontains enough product to install two tubes)
$23.00
Note: Hardware kits are stocked for those customers that loose or misplace those that came with the brace tubes. 12" THRU 24" HIGH PIER REQUIRES: 39" LONG LONGITUDINAL BRACE TUBES 12" THRU 32" HIGH PIER REQUIRES: 44" LONG LONGITUDINAL BRACE TUBES 12" THRU 40" HIGH PIER REQUIRES: 53" LONG LONGITUDINAL BRACE TUBES 12" THRU 48" HIGH PIER REQUIRES: 65" LONG LONGITUDINAL BRACE TUBES Note: Longitudinal & lateral brace tubes must have an angle of between 10 degrees and 45 degrees.
YOUR SET MUST BE DESIGNED BY A REGISTERED PROFESSIONAL ENGINEER IF ANY OF THE FOLLOWING CONDITIONS EXIST: • SITE LOCATION IS WITHIN 1,500 FT. OF COAST LINE • PIER HEIGHT EXCEEDS 48 INCHES • ROOF EAVES EXCEED 16 INCHES • SIDEWALL HEIGHT EXCEEDS 96 INCHES • MAIN I-BEAM SPACING EXCEEDS 99.5 INCHES
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 148
Minute Man, Flex Brace System for Dry & Wet Concrete
THE MINUTE MAN FOUNDATION SYSTEM EXCEEDS REQUIREMENTS
FOR ALL WIND ZONES
Eliminates or reduces most anchors and hardware, saving time and money
ZONE I, II & III LONGITUDINAL AND LATERAL FLEX BRACING SYSTEMS FOR DRY AND WET CONCRETE
INSTALLATIONS Ground anchors may not be required on double wide homes.Marriage wall and perimeter wall anchors must be used when calledfor by home manufacturer. 3,150 lb. working load ground anchorswith stabilizers and frame ties are required on 4 corners of all single
wide homes. Systems must be as equally spaced as possible and no more than 10 ft. from the end of the home. Triple wide homes and tagunits require two additional systems.
Part Number Description Price3-3623 LATERAL FLEX BRACE TUBE KIT with hardware, 60" to 96", (EACH package
contains: 2 ea. brace tubes, 2 ea. 2" x 7-3/4" lateral clamps, 2 ea. 1/2" x 2-1/2"bolt/nut, 2 ea. 1/2" x 1-3/8" washers, 8 ea. 1/4" x 3/4" self drilling screws and 2 ea. 5/8"x 3" sleeve anchors for dry concrete.) Two Lateral flex brace tubes with hardware perpkg., priced separately.
$53.00
3-3625 LATERAL FLEX BRACE TUBE HARDWARE KIT (Each hardware kit contains enoughproduct to install two tubes)
$17.98
3-3628 LONGITUDINAL FLEX BRACE TUBE, 39" LONG With Hardware $25.003-3629 LONGITUDINAL FLEX BRACE TUBE, 44" LONG With Hardware $26.793-3630 LONGITUDINAL FLEX BRACE TUBE, 53" LONG With Hardware (EACH package
contains: 2 ea. Brace tubes, 2 ea. Preassembled beam clips, 4 ea. 3-3/4" x 2-3/4" topcover attachment clips, 8 ea. 1/2" x 1-1/4" bolt/nut and 2 ea. 5/8" x 3" sleeve anchorsfor dry concrete.) Two longitudinal brace tubes with hardware per pkg, pricedseparately.
$28.00
3-3631 LONGITUDINAL FLEX BRACE TUBE HARDWARE KIT (Each hardware kit containsenough product to install two tubes)
$26.98
3-3632 L-ANCHOR FOR WET CONCRETE, 4 per box, priced each not per box (Comes withwasher and nut)
$3.49
18" THRU 24" HIGH PIER REQUIRES: 39" LONG LONGITUDINAL BRACE TUBES
18" THRU 32" HIGH PIER REQUIRES: 44" LONG LONGITUDINAL BRACE TUBES
18" THRU 40" HIGH PIER REQUIRES: 53" LONG LONGITUDINAL BRACE TUBES
Note: Longitudinal & lateral brace tubes must have an angle of between 10 degrees and 45 degrees. Note: Hardware kits are stocked for those customers that loose or misplace those that came with the brace tubes.
YOUR SET MUST BE DESIGNED BY A REGISTERED PROFESSIONAL ENGINEER IF ANY OF THE FOLLOWING CONDITIONS EXIST:
• SITE LOCATION IS WITHIN 1,500 FT. OF COAST LINE • PIER HEIGHT EXCEEDS 48 INCHES
• ROOF EAVES EXCEED 16 INCHES • SIDEWALL HEIGHT EXCEEDS 96 INCHES
• MAIN I-BEAM SPACING EXCEEDS 99.5 INCHES
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 149
Lateral & Longitudinal Pan System
LATERAL AND LONGITUDINAL PAN SYSTEM
by OLIVER TECHNOLOGIES
for HOME SETS
in NORTH CAROLINA
No ground anchors are required on double wide homes.
Two ground anchors are required on each side of singe wide homes and are to be located within two feet from the end with a minimum pull of 3150 lb.
Homes longer than 76 feet have additional requirements.
State of North Carolina only. Brace tubing must be galvanized, when the home manufacturers installation instructions are not available, vertical all tie-downs must be installed not to exceed 8 feet on centers. (wind zone II)
EACH SYSTEM CONSISTS OF THE FOLLOWING ITEMS: GROUND PAN (2.5” DEEP), 1 each CENTERPOINT BRACKET, 1 each U-BRACKET, 1 each 1/2” x 3/16” WASHER, 2 each BOLTS, GRADE 2 (1/2” DIA. x 1” LONG), 2 each NUTS (1/2” HEX), 2 each LONGITUDINAL I-BEAM CLAMP, 4 each I-BEAM FORM CLAMP WITH FLAT CLAMP, 1 each BOLT BAG, LONGITUDINAL BRACING, 1 each BOLT BAG, LATERAL BRACING, 1 each 5’ LATERAL ARM (1.25” & 1.5”) GALVANIZED, 1 each LONGITUDINAL ARMS, GALVANIZED, 2 each Note: Model number is NC 1100 I”V” COMPLETE SYSTEM WITH 39” LONG LONGITUDINAL BRACE ARMS 3-3615 (For 24” to 35” pier height) COMPLETE SYSTEM WITH 44” LONG LONGITUDINAL BRACE ARMS 3-3620 (For 30” to 40” pier height) Note: Longitudinal brace tubes must have a minimum of 40 degree and a maximum of 60 degree angle.
If the following conditions occur, STOP!!! Call Oliver Technologies, Inc. @ 1-800-284-7437: A. Pier height exceeds 48”. B. Roof eaves exceed 16”. C. Roof pitch greater than 7/12. D. Location is within 1500 feet of coast line. E. The following soil conditions; loose sands, firm clays and silts and alluvial fills (soil deposited by flowing water).
Part Number Description Price3-3615 COMPLETE SYSTEM WITH 39" LONG LONGITUDINAL BRACE ARMS $159.003-3620 COMPLETE SYSTEM WITH 44" LONG LONGITUDINAL BRACE ARMS $164.00
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 150
ANCHOR MACHINE by
MINUTE MAN PRODUCTS INC. Frame is made of welded tubular steel. 115-120 volt motordevelops a minimum of 600 lb. of torque. Has pressure sensitiveon/off switch for safer operation. Toggle style forward/reverseswitch allows for clockwise or counter clockwise operation. Has a27" long extension handle. Ninety (90) day limited warranty onparts and labor. Sold with adapter head.
Part Number Description Price3-3560 12 RPM, 1/2 HP MOTOR $898.00
"T" Style
ADAPTERS for
ANCHORING MACHINES These “T” style adapters are made of 3/16" thicksquare steel. Fits square anchoring machine shaftsonly. Comes in 3/4" and 1-1/8" sizes only.
Part Number Description Price3-3541 3/4" x 3/4" $32.003-3544 1-1/8" x 1-1/8" $32.00
Heavy Duty
ADAPTERS for
ANCHORING MACHINES This heavy duty adapter fits over the entirehead of all popular anchors. Simply slip theadapter over the anchor head, install theanchor into the ground, then slip theadapter off the anchor, saving time.
Part Number Description Price3-3545 FITS 1" SQUARE SHAFT $45.003-3546 FITS 3/4" SQUARE SHAFT $55.00
ELECTRICAL SWITCHES Anchoring Machines
Rated 10 amps @ 125 vac, 1/2 hp rated
Part Number Description Price3-3717 ON-OFF TOGGLE SWITCH $17.983-3719 FORWARD/REVERSE SWITCH $17.98
DIGITAL LEVELING SYSTEM
This electronic water level can beused outside or inside the home.Reads in inches and tenths. Willlevel to .2" (1/5") over entire lengthof 100’ tubing. Magnet holds digitaldisplay in place when necessary.Uses a 9-volt battery to power electronics. Uses RV anti-freeze or water as sensing agent. 90 day manufacturer’s warranty.
Part Number Price3-3530 $298.00
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 151
DOUBLE-WIDE ROLLERS
3-ROLLER STYLE
Top plate is of 1/2" thick plate steel, sides are of 3/8" thick steel,capable of supporting 27,000 lb. Each roller has three sealed ballbearing rollers of seamless steel. Overall dimensions: 9" wide x 9"long. Rolls on a user provided 4” x 8” timber, steel beam orequivalent, all capable of supporting weight of section beingmoved. Comes 3 per set.
Part Number Price3-3506 $498.00
DOUBLE-WIDE ROLLERS
5-ROLLER STYLE
Top plate is of 1/2" thick plate steel, sides are of 3/8" thick steel,capable of supporting approximately 48,000 lb. The two main unitshave five sealed ball bearing rollers of seamless steel. Thetongue/jack unit has three rollers. Overall dimensions: 9" wide x17" long. Rolls on a user provided 4” x 8” timber, steel beam orequivalent, all capable of supporting weight of section beingmoved. Comes 3 per set.
Part Number Price3-3509 $698.00
CRIMPING TOOL for
STRAP SEALS Part Number Price3-3505 $277.00
SOIL TEST PROBE This 60 inch long probe is used to test the earths soil density. Use inch pound readings to determine which anchor to use to resist at least 4170 pounds of pull. Comes with wrench adapter and 600 inch pound torque wrench.
Part Number Price3-3507 $228.00
MAGNETIC VALVE ASSEMBLY
for WATER LEVEL
Has 1-3/4" diameter magnet. Brass valvehas barbed fitting to accept 1/4" inside diameter plastic tubing.
Part Number Price3-3547 $35.95
POCKET PENETROMETER
by ELE
Used to determine thecompression strength of topsoil. Use reading to determineproper depth to place footers.
Part Number Description Price3-3504 PENETROMETER $98.003-3508 ADAPTER FOOT $39.00
GFCI CORD SET
Ground fault circuit interrupter is made of safety-yellow materials, Has a nine inch 12/3 AWG cord. 115 volt, 15 amp, 1800 watt outdoor UL listed. Plugs directly into receptacle. Do not use an extension cord between wall receptacle and GFCI.
Part Number Price3-3565 $29.95
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 152
CONTROL SCREW ASSEMBLY Replacement screw assembly for model 24-36 double wide dollykit by Double Wide Systems Co. Overall length is 33 inches.
Part Number Price3-3543 $36.00
COME-A-LONG This 2 ton capacity power pull has a steel cable with die castlocking hooks.
Part Number Price3-3540 $0.00
PLUMBING VENTS All listed vents are designed for flat orslightly pitched roofs.
Part Number Description Price3-3510 2-3/8" I.D., METAL $4.393-3511 2-3/8" I.D., PLASTIC $2.493-3512 5" I.D., METAL $7.79
ROOF FLASHING (Galvanized)
Fits 1-1/4" & 1-1/2" ABS or PVC pipe.
Part Number Price3-3515 $6.98
ROOF VENT Static Type
Made of galvanized steel. Overallheight is 3-3/4", nailing flange is16" x 15". Top hood is 11-1/2" square. Has 9" square opening.Small louvered openings preventsinsects from entering the atticspace. Not for roofs over 6/12pitch slope. Net free area is 50square inches.
Part Number Price3-3518 $14.98
RV VENT by
VENTLINE Body is made of galvanized steel,unlike those that are made of plastic,these will not crack along the baseand sides creating water leaks. Topcover is of white plastic.
Part Number Description Price3-3520 VENT WITH WHITE COVER $29.893-3525 COVER ONLY, WHITE $12.59
SKYLITES by SUN-TEC Smoke Tinted Double Pane
Unbreakable polycarbonate seamless outer pane protects againstleaking, damage and intrusion. Inner pane is made of clearpolycarbonate. Unique ventilation system prevents fogging andcondensation. High-tech engineered polycarbonate blocks over97% of ultra-violet light. Comes with pre-punched flanges ready to mount over roof opening of metal or sloped (3/12 pitch or greater)shingle roof. 5-year limited product warranty. *=Rough opening size.
Part Number Description Price3-FDE1632 16" x 32" (*14-1/4" x 30-1/4") $69.003-FDE1648 16" x 48" (*14-1/4" x 46-1/4") $87.503-FDE2246 22" x 46" (*21-1/2" x 46-1/2") $98.003-FDE2525 25" x 25" (*22-1/2" x 22-1/2") $69.003-FDE2432 24" x 32" (*22-1/4" x 30-1/4") $79.00
SHIPPING WEIGHT 16"x32" 06 LBS.
16"x48’ 10 LBS. 22"x46" 12 LBS. 25"x25" 08 LBS. 24"x32" 10 LBS.
46”x46” 25 LBS.
3-FDE4646 46" x 46" (*46-1/2" x 46-1/2") $198.00
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 153
Antique Style, Plastic
HOUSE NUMBERS Antique style house numbers of black plastic that are 4 inches tall. Comes with mounting screws.
Part Number Description Price3-5000 #0 $0.893-5001 #1 $0.893-5002 #2 $0.893-5003 #3 $0.893-5004 #4 $0.893-5005 #5 $0.893-5006 #6 $0.893-5007 #7 $0.893-5008 #8 $0.893-5009 #9 $0.89
Elegant Style, Solid Brass
HOUSE NUMBERS Elegant style house numbers of solid brass that are 4 inches tall. Comes with mounting screws.
Part Number Description Price3-5020 #0 $2.893-5021 #1 $2.893-5022 #2 $2.893-5023 #3 $2.893-5024 #4 $2.893-5025 #5 $2.893-5026 #6 $2.893-5027 #7 $2.893-5028 #8 $2.893-5029 #9 $2.89
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 154
Contact Cement
WELDWOOD THE ORIGINAL
CONTACT CEMENT Fast dry formula exceeds industry performancerequirements. Dries in 15-20 minutes. Highheat resistance. Water resistant when dry.
Part Number Description Price4-1029 1 QUART $11.98
Construction Adhesive
Liquid Nails, Interior/Exterior
NAIL POWER CONSTRUCTION
ADHESIVE Heavy Duty
A high performance adhesive for multi-purpose use.Recommended for use on paneling, drywall, plaster,decks, loose tile, plywood, treated lumber, concrete andbrick. Not recommended for polystyrene foam or panels. For interior or exterior use.
Part Number Description Price4-2017 10.2 FL. OZ. TUBE $2.98
Roof Cement
Wet or Dry, Plastic
ROOF CEMENT WET OR DRY
Plastic Use on metal roofs, asphalt roofs, and compositionroofs. Use around chimneys, flues, plumbing vents, etc.
Part Number Description Price4-1018 10.1 FL.OZ. TUBE $0.00
Constructive Adhesive
MAX BOND CONSTRUCTION
ADHESIVE Multi-Purpose
This premium grade multi-purpose interior/exterior construction adhesive is ideal for bonding paneling, wood, drywall, concrete, steel, aluminum, cork, polystyrene and urethane foams. Excellent for installing tub/shower wall kits. 10.6 fluid ounces per tube.
Part Number Price4-2019 $5.98
Boss Multi-Purpose
CONSTRUCTION ADHESIVE Multi-Purpose
by BOSS
Bonds most types of construction materials such as polystryene foam, paneling, marble, gypsum board, fiberglass panels, wood, paper and metal. An excellent waterproof adhesive for all types of tub/shower wallkits.
Part Number Description Price4-2016 10.3 FL. OZ. TUBE $5.98
Construction Adhesive
Liquid Nails, Exterior
LIQUID NAILS ADHESIVE
A fast bonding, superior quality, waterproof interior grade adhesive that stays flexible. Bridges gaps up to 3/8" and offers up to 10 minutes working time. Not for exterior use.
Part Number Description Price4-2018 10.5 FL.OZ TUBE $3.69
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 155
Fire Mortar
FIRE MORTAR A non-combustible silicate cement that can withstandextremely high heat. Formulated for repairing chimneys,fireplaces, wood stoves and appliances. Can be used onwood frame construction where non-combustible sealantis required. This product has excellent adhesion and setsto become rock hard when cured. Conforms to ASTME-136 and can withstand temperatures of up to 3000degree F. 10.1 fluid ounce cartridge.
Part Number Price4-1020 $5.98
Fiberglass Repair Kit
FIBERGLASS, PORCELAIN AND PLASTIC REPAIR KIT
Repairs holes up to 1” in diameter and cracks up to 5”long. May use on showers, tubs, sinks and toilets.Handling time 4 to 5 minutes, set time 20 minutes, curesin 24 hours. Holding strength of 1500 PSI. White & almond in same package.
Part Number Price4-1024 $19.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 156
Kool Seal, Blue Label
BLUE LABEL (SILVER) ROOF COATING by KOOL SEAL This original Blue Label Premium quality Kool Seal is so good that it has a 5-year factory product warranty, whenapplied according to manufacturer’s instructions. Blue Label Kool Seal has the finest aluminum pigments available, and has up to three times more pigment than most other brands on the market. These high grade aluminum pigmentsare microscopic flakes, when dispersed in asphalt, have the ability to migrate, over time, to the surface where theyreflect the sun’s heat. This reflect ability causes the home to be cooler, and prolongs the coating’s life. Cover approximately 80 to 100 Sq. Ft. per Gallon when applied as per instructions.
Part Number Description Price4-1055 5-GALLON $114.594-1057 1-GALLON $29.95
Kool Seal, Aluminum
ALUMINUM ROOF COATING by KOOL SEAL An economical good quality aluminum roof coating with less aluminum pigment than the other grade of Kool Seallisted on this page. Reinforced with non-asbestos fibers for a longer lasting roof life. Cover approximately 50 to 75 Sq. Ft. per Gallon when applied as per instructions.
Part Number Description Price4-1059 5-GALLON $79.98
Kool Seal, White Elastomeric
WHITE ELASTOMERIC ROOF COATING by KOOL SEAL This product reflects 90% or more of the suns rays saving up to 30% in energy costs. Forms a thick rubber-like blanket of protection against moisture and the elements. The durable acrylic elastomeric resin expands and contracts with your roof for a longer product life. Cured elastomeric film is mildew and algae resistant. Soap and water cleanup while wet.On smooth metal, coverage is approximately 100 sq. ft. per gallon when applying required two coats. Five (5) year limited product warranty when applied as per instructions.
Part Number Description Price1-GALLON NOT AVAILABLE
4-1065 5-GALLON $86.69
Kool Seal, Premium White Elastomeric
PREMIUM WHITE ELASTOMERIC ROOF COATING by KOOL SEAL Environmentally engineered premium white elastomeric kool seal saves up to 35% on energy costs while protectingagainst water damage. Higher solids content forms a thick rubber-like blanket for better coverage and protection. Expands and contracts with the temperature and is durable in all climates. Is mildew and algae resistant. Helps toabsorb sound. Soap and water clean-up while wet. On smooth metal, coverage is approximately 100 sq. ft. per gallon when applying required two coats. Ten (10) year limited product warranty when applied as per instructions.
Part Number Description Price4-1067 1-GALLON $30.474-1068 5-GALLON $129.00
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 157
Kool Seal, Patching Cement
PATCHING CEMENT White Acrylic KOOL SEAL
Formulated with durable acrylicresin and special reinforcingmaterials. Stops leaks on damp ordry surfaces. Long lasting, tough,flexible patch seals out water and ismildew resistant. Blends in onexisting white roofs and resistscracking, peeling and blistering.Soap and water cleanup while wet.
Part Number Description Price4-1060 QUART $8.984-1061 GALLON $23.37
Kool Seal, Storm Patch
STORM PATCH All Weather Rubberized
Cement KOOL SEAL
This all-weather premiumrubberized cement actuallydisplaces water from wet surfacesand creates a tight seal. Ideal forsealing around flashing,chimneys, vents, skylights, joints,gutters, pipes, and similar objects.Clean-up tools with kerosene,paint thinner or mineral spiritsimmediately after use.
Part Number Description Price4-1062 GALLON - BLACK $21.894-1063 TUBE - CLEAR $7.184-1064 TUBE - BLACK $3.29
Kool Seal, Glass Membrane
GLASS MEMBRANE Reinforcement Fabric
Excellent for repairing those troublesome seams orjoints that keep pulling apart. May be used withasphalt based or white roof coatings.
ll one gallon pails have .90 gallon of product.
Part Number Description Price4-2025 4" WIDE x 40 FT. LONG $6.79
Aldo Products, Great White
GREAT WHITE ELASTOMERIC ROOF COATING
by ALDO PRODUCTS CO.
Great White roof coating 100 is atechnologically advanced fire retardant,thrixotropic, acrylic elastomericcoating that has been formulated tohave exceptional adhesion to a varietyof substrates; such as primed wood, metal roofs, concrete and masonry. Itsunique formulation incorporateselastomeric acrylics resins, reinforcinglaminar pigments and othernonmigrating fire retardants to producea seamless, flexible, durable membranehaving exceptional weather ability, ultraviolet and fire resistance.Suggested coverage is 3-gallon per 100 square ft. or 15 mils thick.
Part Number Description Price4-1051 5-GALLON $89.00
Aldo Products, Butyl Seam Seal
BUTYL SEAM SEAL by
ALDO PRODUCTS CO.
Butyl seam seal, (ALDOSEAL 747), is a single component elastomer sealer specially formulated to provide a waterproof, weather resistant membrane with excellent permeability and ultraviolet protection. ALDOSEAL 747 offers good elongation and tensil strength to resist lateral movement and allow for expansion and contraction of the substrate. May apply acrylic base or asphalt base roof coating over this product within one hour of application. Color is white.
Part Number Description Price4-1048 GALLON $49.95
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 158
Silicone Caulk
SILICONE CAULKING
by BOSS “The Choice of the
Construction Industry” 100 % Silicone, 100% Acetoxy cure, 10.1 fl. oz. pertube.
Part Number Description Price4-2101 CLEAR $4.984-2102 WHITE $4.984-2103 ALUMINUM $4.984-2104 BLACK $4.984-2107 BRONZE $4.98
Acrylic Latex Caulk
ACRYLIC LATEX CAULKING
by BOSS “The Choice of the
Construction Industry” Siliconized, Interior/Exterior use, Paintable after 60minutes of curing, 10.1 fl. oz. per tube.
Part Number Description Price4-2121 CLEAR $4.894-2122 WHITE $3.894-2123 ALMOND $3.894-2124 BROWN $3.894-2125 GRAY $3.89
Tub & Tile Caulk
Boss
Tub & Tile SILICONE CAULKING
by BOSS “The Choice of the
Construction Industry” Mildew resistant, Non-yellowing, Paintable, 10.1 fl. oz.per tube.
Part Number Description Price4-2118 WHITE $5.794-2119 ALMOND $5.79
Silicone Caulk
SILICONE CAULKING
by BOSS
3 fl. oz. per tube.
Part Number Description Price4-1199 WHITE $2.984-2000 CLEAR $3.98
Tub & Tile Caulk
White Lightning
TUB & TILE CAULK
by White Lightning
Siliconized acrylic mildew and rust resistant. Excellent adhesion. Stays flexible.5.5 oz. tube.
Part Number Description Price5-1220 ALMOND $3.595-1221 WHITE $3.59
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 159
PEEL & SEAL An aluminum foil backed self-adhesive black butyl rubber flashing for quick,long lasting weather-proof seal.
Part Number Description Price4-2080 3" W x 33.5' L $17.894-2120 6" W x 33.5' L $25.98
SPEED MIXER This is a true mixer, not a paddle type stirrer.Entirely constructed of nickel-plated steel to resistcorrosion. For use with 3/8" or larger drill motor.Max. of 900 rpm. May be used to mix paint, roofcoatings and other similar density products. The small unit (2-3/8" head with 16" long x 3/8"diameter hex shaft) is ideal for one gallon pailswhile the large unit (4" diameter head with 24"long x 7/16" diameter hex shaft) works best in fivegallon pails.
Part Number Description Price4-2106 2-3/8" DIA. HEAD $6.594-2109 4" DIA. HEAD $11.19
SKELETON CAULKING GUN Made of heavy steel. 9" long for use with 10.1 oz. or similar sizetubes. The choice of the construction industry.
Part Number Price4-2110 $6.98
CAULK FINISHER Made of plastic, Bead size may be enlarged bytrimming end of finisher.
Part Number Price4-2112 $1.69
ROOF COATING BRUSH
This high quality inexpensive nylonbristle brush is ideal for applying roofcoatings.
Part Number Description Price4-2030 2-1/2" WIDE x 7" LONG $3.99
HANDLE for
ROOF COATING BRUSH
This heavy duty wood handle has a tapered end that fits snug into roof coating brush.
Part Number Description Price4-2031 1-1/8" DIA. x 54" LONG $4.49
BRUSH & HANDLE COMBINATION
Roof Coating
This combination roof coatingbrush and handle set has a 7” longx 2-1/2” wide wood brush with 2” long nylon bristles. The paintedscrew-in metal handle is 48” long x 7/8” diameter.
Part Number Price4-2033 $7.49
PAINT ROLLER KIT
Contains metal paint tray, 9"roller frame, and a 9" all-paint roller.
Part Number Price4-2037 $5.49
ROLLER FRAME
This 9 inch wire roller frame has formed grip threaded handle.
Part Number Price4-2039 $2.69
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 160
HANDLE for
ROLLER FRAME
This heavy duty wood handle has a threaded end that fitsinto the roller frame handle.
Part Number Description Price4-2038 15/16" DIA. x 60" LONG $4.98
Professional Grade
PAINT ROLLERS
These all purpose, 9", reusable rollers may be used with latex or oilbased paints. For smooth (1/4" nap) and medium (3/8" nap)surfaces.
Part Number Description Price4-2040 1/4" NAP $4.754-2046 3/8" NAP $5.46
Utility Grade
Part Number Description Price4-2041 1/4" NAP $3.654-2048 3/8" NAP $2.69
PAINT BRUSHES
Economy Grade White natural bristle with unfinished, sanded woodhandle.
Part Number Description Price4-2042 2" $0.894-2043 3" $1.29
Work
LEATHER PALM WORK GLOVES
Long lasting split cow hide palm, forefinger, fingertips & knuckle. Safety cuff for better protection. Striped cotton back & 100% cotton lining. One size fits all.
Part Number Price4-2050 $3.29
Jersey
JERSEY GLOVES Soft breathable, unlined, 100% cotton jersey. One size fits all.
Part Number Price4-2052 $1.79
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 161
Hex Head Screws, 1/4" Non-Slotted Hex Head
# 8, 1/2" thru 2" Long, Zinc Plated Steel
ZINC PLATED # 8 x 1/4" NON-SLOTTED
HEX WASHER HEAD
Part Number Description Price4-2500 #8 x 1/2" $0.024-2500M Box of 1000 $10.004-2510 #8 x 3/4" $0.0244-2510M Box of 1000 $13.004-2520 #8 x 1" $0.0244-2520M Box of 1000 $14.004-2530 #8 x 1-1/4" $0.034-2530D Box of 500 $8.004-2540 #8 x 1-1/2" $0.0364-2540D Box of 500 $9.004-2550 #8 x 2" $0.054-2550D Box of 500 $13.00
# 8, 1" thru 2" Long, Painted Heads
# 8 HEX HEAD SCREWS PAINTED HEADS
1/4 NON-SLOTTED HEAD
Part Number Description Price4-2552 #8 x 1" WHITE $0.0354-2552B #8 x 1" WHITE, 250 & up $0.024-2554 #8 x 1-1/2" WHITE $0.044-2554B #8 x 1-1/2" WHITE, 250 & up $0.034-2553 #8 x 2" WHITE $0.064-2553B #8 x 2" WHITE, 250 & up $0.0364-2555 #8 x 1" BROWN, $0.0354-2555B #8 x 1" BROWN, 250 & up $0.004-2556 #8 x 2" BROWN $0.064-2556B #8 x 2" BROWN, 250 & up $0.0384-2567 #8 x 1" ALMOND $0.0354-2567M #8 x 1" ALMOND, Box of 1000 $19.004-2568 #8 x 1" TAN $0.0354-2568M #8 x 1" TAN, Box of 1000 $19.004-2569 #8 x 1" CREAM $0.0354-2569M #8 x 1" CREAM, Box of 1000 $19.004-2570 #8 x 1" GRAY $0.0354-2570M #8 x 1" GRAY, Box of 1000 $19.004-2571 #8 x 1" BLACK $0.0354-2571M #8 x 1" BLACK, Box of 1000 $19.00
Countersunk Oval Head
COUNTER SUNK SCREWS
Part Number Description Price4-2579 Countersunk, Phillips, Stainless Steel.,
#6 x 1-1/4"$1.98
4-2581 Countersunk, Clutch, Nickel Plated., #5 x1-1/2"
$0.00
4-2582 Countersunk, Square, Zinc Plated., #6 x1-1/4"
$0.015
4-2583 Countersunk, Phillips, Zinc Plated., #8 x1"
$0.04
Flat Head Hinge Screws
FLAT HEAD SCREWS
Part Number Description Price4-2585 Flat, Countersunk, Phillips, Brass Pltd.,
#7 x 1"$0.05
4-2586 Flat, Countersunk, Phillips, Brass Pltd.,#7 x 1-1/2"
$0.07
4-2584 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 1"
$0.05
4-2587 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 1-1/2"
$0.07
4-2588 Flat, Countersunk, Phillips, Brass Pltd.,#8 x 3"
$0.10
Round Washer Head
ROUND WASHER HEAD SCREWS
Part Number Description Price4-2591 Zinc Plated Steel, use #2 square insert
bit., #8 x 1"$0.00
4-2592 Zinc Plated Steel, use #2 square insertbit. Deep thread., #8 x 3"
$0.05
4-2592B Zinc Plated Steel, use #2 square insertbit. Deep thread., #8 x 3", 250 & up
$0.04
4-2595 Zinc Plated Steel, use #2 square insertbit. Deep thread., #10 x 5"
$0.12
4-2595B Zinc Plated Steel, use #2 square insertbit. Deep thread., #10 x 5", 250 & up
$0.10
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 162
Flat Countersunk Square Head
Plain Steel
FLAT COUNTERSUNK SQUARE HEAD SCREWS
Plain Steel
Part Number Description Price4-2590 8 x 2" $0.044-2590B 500 & up $0.0254-2600 #8 x 3" $0.054-2600B 250 & up $0.0354-2601 #8 x 4" $0.054-2601B 250 & up $0.044-2602 #10 x 5" $0.094-2602B 200 & up $0.07
Hot Dip Galvanized
FLAT COUNTERSUNK SQUARE HEAD DEEP THREAD
Hot Dip Galvanized
Part Number Description Price4-2610 #8 x 2-1/2" $0.084-2610B 250 & up $0.064-2611 #8 x 3" $0.094-2611B 250 & up $0.07
Hex Head Screws, 1/4" Non-Slotted Hex Head
# 8, 3/4" Long, Aluminum
ALUMINUM # 8 x 1/4" NON-SLOTTED
HEX WASHER HEAD
Part Number Description Price4-2630 #8 x 3/4" $0.034-2630M Box of 1000 $32.00
# 9, 3/4" & 1" Long, Aluminum
ALUMINUM #9 SIZE
1/4" SLOTTED HEX WASHER HEAD
This #9 screw is ideal for replacing the normal size (#8) screws in mobile homes and RV’s. Thelarger body size fits tighter where a #8 screw was previously installed. The extra large washer head covers up ugly rust stains. Also, the washer headis designed to help prevent screw from backing-out over time.
Part Number Description Price4-2661 #9 x 3/4" $0.0394-2661M Box of 1000 $38.004-2662 #9 x 1" $0.0464-2662M Box of 1000 $42.00
# 8, 1/2" Long, Self-Drilling, Zinc Plated Steel
ZINC PLATED STEEL SELF-DRILLING
# 8 x 1/4" NON-SLOTTED HEX WASHER HEAD
Part Number Description Price4-2560 #8 x 1/2" $0.024-2560M Box of 1000 $14.00
# 10, 1/2" Long, Zinc Plated
ZINC PLATED #10
5/16" NON-SLOTTED HEX HEAD
Part Number Description Price4-2565 #10 x 1/2" $0.03
Wood Screws
WOOD SCREWS SOLID BRASS
Part Number Description Price4-2598 Wood Screw, Solid Brass, Flat,
Countersunk Head, Phillips. Excellentfor mounting toilet flanges., #14 x 1-1/4",Package of 8.
$2.19
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 163
LAG SCREWS 9/16" Hex Head
Raw Steel Packaged with fender washers
Part Number Description Price4-2690 3/8" dia. x 3", 50/pkg $0.284-2691 3/8" dia. x 5", 50/pkg $0.354-2692 3/8" dia. x 6", 25/pkg $0.394-2694 3/8" dia. x 8", 25/pkg $0.56
Spiral Drive, Round Head
SPIRAL DRIVE NAILS ROUND HEAD
PLATED STEEL
1-1/4" LONG 50 PER PKG
Part Number Description Price4-2701 NICKEL PLATED #4 $1.394-2702 BRASS PLATED #4 $1.394-2703 NICKEL PLATED #6 $9.98
SCREW CAP PLASTIC
9/16” outside diameter plastic screw caps willaccommodate #6 thru #10 screw withcountersunk head. Priced per package of 25.
Part Number Description Price4-2720 WHITE $4.984-2721 BLACK $4.98
FENDER WASHER Flat Zinc Plated Steel
3/8" diameter hole, 1" outside dimensions,1/16" thick. 3550 per case. 50 lbs per case.Priced per each.
50 per bag
Part Number Price4-2730 $0.03
Green Cleaner
GREEN CLEANER Concentrate
Removes grease and grime when used at full strength, yet still effective for glass and crystal when diluted. Non-toxic, non-corrosive and biodegradable.
Part Number Description Price4-2059 22 oz. spray $4.98
Black Streak Remover
BLACK STREAK REMOVER Use this tough 100% spray to quickly and easily remove even the most stubborn black streaks. It’s strong enough to clean, but will not harm the paint.
Part Number Description Price4-2063 32 oz. spray $5.494-2064 1 gal. $18.98
Trailer Glitter
TRAILER GLITTER Remove road grease, dirt and grime in minutes with this concentrate cleaner. Adds sparkle and shine and protects any painted surface. Also great for removing mildew and stains.
Part Number Description Price4-2065 32 oz. $4.984-2066 1 gal. $14.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 164
Rope Caulk
ROPE CAULK Press in place to seal cracks and stop drafts.Will not harden or dry out. One roll coversapproximately 30 ft. Woodstone color.
Part Number Price4-2014 $3.49
Butyl Tape
BUTYL TAPE Sealant
Premium quality, permanent resilienceand elongation characteristics. Excellentfor sealing problem areas. Great for usewhen installing doors & windows. Gray in color.
Part Number Description Price4-2021 1/8" x 3/4" x 30 ft. $4.39
Duct Tape
Polybutylene, UL181
DUCT TAPE Polybutylene
Code approved UL 181B-FX For use on vinyl and foil backed flexible ductand duct wrap. 3.0 mil thick, has cold weather (-35deg. F) acrylic adhesive. 2" x 120 yds.
Part Number Description Price4-2071 BLACK $10.494-2072 METALLIC $10.49
Coated Cloth
DUCT TAPE Coated Cloth
Super sticky, conforms easily to items beingtaped, super performance. 10 MIL thickness.Gray color.
Part Number Description Price4-2075 2" x 60 yds. $6.98
Coated Cloth, UL181
DUCT TAPE Coated Cloth
Code Approved UL 181B-FX For use on vinyl and foil backed flexible ductand duct wrap. 2"x 60 yds.
Part Number Description Price4-2074 BLACK $15.984-2076 SILVER $15.98
High Tack Tape
HIGH TACK TAPE
The best tape on the market for repairing and patching vapor barrier under manufactured homes. Firstline No. 620. Black.
Part Number Description Price4-2077 2" x 36 yds. $18.98
Duct Tape
Aluminum, UL181
ALUMINUM FOIL DUCT TAPE
Code Approved UL 181A-P For use on foil faced products such as duct board, duct wrap, and flexible duct.
Part Number Description Price4-2078 2-1/2" x 60 yds. $21.98
Duct Tape
Aluminum Foil
ALUMINUM FOIL TAPE
2 MIL aluminum foil has easy release liner.
Part Number Description Price4-2079 2" x 60 yds. $10.98
Duct Tape
Aluminum with Heavy Butyl
ALUMINUM FOIL DUCT TAPE
with HEAVY BUTYL ADHESIVE
2-mil dead soft aluminum foil, heavy duty, all-weather duct tape with 43-mil butyl rubber adhesive. Excellent for repairing mobile home duct work. Has 20 lbs. per inch tinsel strength. Has easy release liner.
Part Number Description Price4-2080 3" x 30 ft. $17.89
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 165
Electrical Tape
ELECTRICAL TAPE Vinyl
UL approved, flame retardant 7 MIL tape suitablefor 600 volts or less and not more that 176 deg. F.
Part Number Description Price4-2081 3/4" x 60 ft., BLACK, Pro Grade $1.984-2082 3/4" x 66 ft., RED $1.494-2083 3/4" x 60 ft., BLACK, Econo Grade $0.98
Duct
DUCT TAPE INSULATION TAPEFoil Scrim Kraft (FSK) Tape
Non-tearable, diamond patterned 7-mil foil backing with an aggressive (AWF)all weather formula rubber adhesive.This superior adhesive system is perfectin application temperatures rangingfrom -25 deg F to + 250 deg F. Thistape is a must when installing orrepairing foil-backed duct insulation.Easy release liner. UL 723characteristics. Rolls are silver in color.
Part Number Description Price4-2088 3" x 50 yds. $13.98
Carpet Tape
CARPET TAPE HOT MELT
Professional Grade This quick lock seaming tape is heat activatedfor bonding carpet seams.
Part Number Description Price4-2084 3" x 66 yds. $0.00
Cork Tape
CORK INSULATION TAPE
Part Number Description Price4-2087 1/8" x 2" x 30 ft. $11.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 166
Hex
HEX DRIVERS
Part Number Description Price4-1079 3/16" $4.294-1081 5/16" $4.294-1083 3/8" $4.294-1085 7/16" $4.294-1084 1/2" $4.29
Square
SQUARE DRIVER
Part Number Description Price4-3211 #1 SQUARE $4.194-3212 #2 SQUARE $4.694-3113 #3 SQUARE $4.98
Clutch
CLUTCH DRIVERS
Part Number Description Price4-3220 5/32" CLUTCH $4.98
SCREWDRIVER REVERSIBLE BLADES
4 IN 1 Has Phillips #1 and Phillips #2, slotted 3/16" and 5/16"reversible blades.
Part Number Price4-3224 $6.19
6-IN-1 DRIVER KIT
Includes:
#1 SQUARE #2 SQUARE #2 PHILLIPS
5/32" CLUTCH 3/16" SLOTTED
1/4" HEX
BITS STORE IN HANDLE.
Part Number Price4-3225 $11.98
MEGA-MAGNETIC BIT HOLDERS
By IVY CLASSIC
These bit holders have twomagnets with forty times theholding power of other bit holders.One magnet holds the bit in placewhile the other magnet holds thefastner in place. The ¼” hex driveis made of stainless steel. The twenty-three inch long ¼” has a non-rotating outer sleeve for safer steadier operation.
Part Number Description Price4-3270 3" LONG $7.194-3274 23" LONG $17.69
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 167
Square
INSERT BITS (SQUARE)
One inch long, 1/4" hex drive.
Part Number Description Price4-3228 #0 SQUARE $0.494-3230 #1 SQUARE $0.494-3232 #2 SQUARE $0.494-3234 #3 SQUARE $0.89
Phillips
INSERTS BITS (PHILLIPS)
One inch long,1/4" hex drive.
Part Number Description Price4-3235 #1 PHILLIPS $0.494-3236 #2 PHILLIPS $0.49
Slotted
INSERT BITS (SLOTTED)
One inch long, 1/4" hex drive.
Part Number Description Price4-3238 #2 SLOTTED $0.49
Clutch
INSERT BITS (CLUTCH)
One inch long, 1/4" hex drive.
Part Number Description Price4-3240 5/32" CLUTCH $1.69
Square
POWER BITS (SQUARE)
Part Number Description Price4-3241 #1 SQUARE x 2" $0.984-3242 #2 SQUARE x 2" $1.294-3247 #2 SQUARE x 4" $1.49
Phillips
POWER BITS (PHILLIPS)
Part Number Description Price4-3243 #1 x 2" PHILLIPS $0.004-3244 #2 x 2" PHILLIPS $0.984-3249 #2 x 3-1/2" PHILLIPS $1.254-3245 #3 x 3-1/2"PHILLIPS $1.494-3258 #2 x 6" PHILLIPS $2.39
Slotted
POWER BIT (SLOTTED)
Part Number Description Price4-3246 # 8-10 x 2" SLOTTED $1.29
Clutch
POWER BIT (CLUTCH)
Part Number Description Price4-3248 5/32" x 2" CLUTCH $2.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 168
Magnetic Socket
Power Bits
POWER BITS MAGNETIC
SOCKET
1/4" HEX DRIVE
Part Number Description Price4-3250 1/4"HEX x 2"LONG (Tapered Socket
End)$3.98
4-3255 1/4"HEX x 4"LONG $8.394-3256 1/4"HEX x 6"LONG $6.894-3251 5/16"HEX x 2"LONG $2.984-3252 5/16"HEX x 4"LONG $7.294-3253 5/16"HEX x 6"LONG $7.98
Insert Bit Holder
INSERT BIT HOLDER (MAGNETIC)
Holds all 1/4" shank bits.
Part Number Price4-3231 $3.69
Magnetic Socket
MAGNETIC SOCKET
1/4" square drive.
Part Number Description Price4-3229 1/4" HEX $4.984-3226 5/16" HEX $4.98
Socket Adapter
SOCKET ADAPTER
1/4" hex x 1/4" square. 1-3/8 inches long.
Part Number Price4-3227 $2.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 169
4-Stop Positions
UTILITY KNIFE
This all metal knife has 4-stop positions for blade, with bladestorage in handle. Comes with one blade.
Part Number Price4-3314 $3.98
Rapid Reload
RAPID RELOAD UTILITY KNIFE “Ivy Classic Brand”
The Power Pro Grip handle is designed for comfort & balance.Five blade rapid reload cartridge fits into handle. Simply press thered button to release the blade and slide a new one into place. Usesstandard utility blades. Comes with 6 blades.
Part Number Description Price4-3315 KNIFE WITH 6-BLADES $7.984-3316 RAPID RELOAD CARTRIDGE,
5-BLADES$1.19
Retractable W/ Snap-Off Blade
UTILITY KNIFE Retractable with snap-off blade and safety lock, easy bladereplacement. 3/4" wide blade.
Part Number Price4-3317 $1.32
Double End Hook Blade
HOOK BLADE FOR
UTILITY KNIVES This heavy duty deep throat hook blade fits most popular utility knives. 5 blades per package.
Part Number Price4-3324 $2.49
Heavy Duty, 5 Blades Per Package
UTILITY KNIFE BLADES “Ivy Classic Brand”
Heavy duty blades for industrial and home use. For general cutting, trimming, and scraping. Made of high carbon steel. 5 blades per package.
Part Number Price4-3321 $1.32
Heavy Duty, 100 Pack Dispenser
UTILITY KNIFE BLADES by
Ivy Classic This 100 pack dispenser is handy and economical for volume users of heavy duty blades. Made of high carbon steel.
Part Number Description Price4-3323 100 PER PACKAGE $16.98
Single End Hook Blade
HOOK BLADE by
STANLEY For cutting vinyl or linoleum floor coverings, roofing and similarmaterials. For use with fixed blade knives only. # 11-980
Part Number Price4-3322 $3.98
Fixed Blade Style
UTILITY KNIFE by STANLEY
Fixed Blade Style
For use with all fixed style blades. Contractor grade.
Part Number Price4-3329 $5.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 170
HACKSAW (ADJUSTABLE)
Part Number Description Price4-3325 ECONOMY $6.984-3326 DELUXE GRADE $10.98
HACKSAW BLADES High quality blades made of high carbon steel. 24 teeth per inch.
Part Number Description Price4-3327 10" $1.684-3328 12" $1.77
MEASURING TAPE This 25 ft. tape has vivid black numbers on ayellow blade with red indicators for every foot.Triple riveted end hook. Deluxe chrome tensionbelt clip. Bright neon color makes it harder tomisplace.
Part Number Price4-3300 $6.98
AVIATION SNIPS “Ivy Classic Brand”
Cuts straight to wide curves, left or right. The non-slip serratedjaws cut up to 18 gauge low carbon cold rolled steel. Self-opening jaws.
Part Number Price4-3310 $12.85
TORPEDO LEVEL Has level, plumb, and 45 deg. bubbles. 9" long. Has strongmagnet to hold level in position.
Part Number Price4-3331 $4.98
WIRE BRUSH Shoe handle style, tempered andgalvanized bristles. Overall length10".
Part Number Price4-3340 $1.98
PUTTY KNIFE 1-1/4" wide steel blade with plastic handle. Stiff blade.
Part Number Price4-3345 $2.79
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 171
Poly, PVC & Pex Pipe
TUBING CUTTER “LiL Nipper”
Cuts poly, PVC and pex tubing, andrubber hose up to 1-5/8" O.D. Lightweight, safe and tough. Stainless steelblade.
Part Number Description Price4-3500 TUBING CUTTER $12.004-3502 BLADE ONLY, “LI’L NIPPER”, 2/PKG $8.984-3504 BLADE ONLY, “IVY CLASSIC”, 1/PKG $4.98
PVC Pipe
TUBING CUTTER FOR
PVC PIPE Cuts PVC pipe up to 1-5/8" O.D. Heavy duty metal construction,replaceable stainless steel blade.
Part Number Description Price4-3501 TUBE CUTTER $15.984-3503 BLADE ONLY $7.49
SAND CLOTH 120 GRIT
1-1/2" WIDE
Part Number Description Price4-3506 2 YDS $1.994-3507 10 YDS $5.49
SOLDER 100% Lead Free
Lower melting point than 95/5, wide workingrange similar to 50/50. 1 lb. spool.
Part Number Price4-3532 $39.95
SOLDERING PASTE
NOKORODE Works on all solder alloys including 95-5 and all lead free solders.
Part Number Price4-3535 $2.29
WD-40
WD-40 Spray Lubricant
with Smart Straw Feature
Stops squeaks, loosens rusted parts, frees sticky mechanisms and protects metal. New smart straw features a permanently attached straw that sprays two ways. Simply flip it up for a precision stream and down for a regular spray. 11ounce can.
Part Number Price4-3542 $8.98
Liquid Wrench
LIQUID WRENCH Spray Lubricant
with Teflon This non-flammable super lubricant stops squeaks, loosens rust and penetrates. 11 oz. can.
Part Number Price4-3543 $4.49
Silicone
SILICONE Spray Lubricant
Stops squeaks, waterproofs, rust proofs and lubricates. Compatible with all metals, rubber and wood. 12 oz. can.
Part Number Price4-3545 $5.59
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 172
HYDRAULIC AXLE JACKS
Gives Long, Trouble-Free
Performance
MULTI-POSITION DESIGNCan Be Used At Any Angle
Lifetime Limited Warranty
Unlike many other jacks on the market, these jacks can be rebuilt, should they fail to operate. We stock rebuild kits and several other parts.
Part Number Description Price4-76412 12 TON, Standard Height, Fully
Extended 18-3/4"$139.00
4-76512 12 TON, Low Height, Fully Extended13-3/16"
$139.00
4-76520 20 TON, Standard Height, FullyExtended 10-1/16"
$198.00
NORCO JACK REBUILD KITS
Rebuild kit includes: O-rings, filler plug, seals, chrome check ballsand pump plunger.
Part Number Description Price4-5000 20 TON $29.984-5001 12 TON STANDARD $29.95
REPLACEMENT PINS FOR NORCO JACKS
Comes with e-ring Part Number Description Price4-5002 PIN, LINK, 5/16"dia. x 15/16" long,
(Lever linkage to jack body)$1.29
4-5003 PIN, LINK, 5/16" dia. x 1" long, (Leverlinkage to pump plunger)
$1.29
REPLACEMENT LIMIT PIN
NORCO JACKS
Part Number Description Price4-5006 9/32" diameter x 1-3/4" long, (# 6 on
exploded parts diagram)$1.98
RUBBER OIL FILL PLUG
Part Number Price4-5004 $0.69
HARDWOOD BOARDS
8" x 16" x 1" 10 PER BUNDLE
600 PALLET
Part Number Price4-5010 $1.13
HARDWOOD WEDGES
1" x 4" x 10" 50 PER BUNDLE
5,000 PALLET
Part Number Price4-5015 $0.32
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 173
FOUNDATION PADS ABS
Approved for use in NC as footers.They are lightweight, easy toinstall, will not crack or split andsaves on labor cost. Limited lifetime warranty.
Part Number Description Price4-5016 16" x 16" x 3/4" - 20 per Bundle $5.394-5018 20" x 20" x 3/4" - 10 per Bundle $8.98
FOUNDATION PAD Round
This round pad is ideal for use asdecking footer where concrete footersare not required. Pads are made fromrecycled automobile tires and selectresins. Will not rot or deteriorate and islight weight, only 3 lbs. each. 15-3/4” diameter x 1-1/2” thick.
Part Number Price4-5020 $13.98
.030" Narrow
STAPLES by
DUO-FAST
.030" NARROW CROWN STAPLES
5000 PER BOX
Part Number Description Price4-3416 1/2" - Natural $14.004-3418 9/16" - Natural $14.504-3416-4 1/2" - Tan $17.794-3418-4 9/16" - Tan $19.584-3416-1 1/2" - Brown $17.794-3416-3 1/2" - White $17.794-3418-3 9/16" - White $19.58
.050" Narrow
STAPLES by
DUO-FAST
.050" NARROW CROWN STAPLES
5000 PER BOX
Part Number Description Price4-5418 9/16" - Natural $12.3945418-3 9/16" - White $19.58
POP RIVETS Aluminum
25 Per Package
Part Number Description Price4-5430 1/8" DIAMETER x 3/8" LONG, (Has 1/4"
maximum grip)$1.25
4-5431 3/16" DIAMETER x 11/16" LONG, (Has1/2" maximum grip)
$2.29
“S” HOOK This 1-1/2" long open type S-hook is made of heavy gauge zinc coated steel. Maximum weight limit is 40 pounds.
Part Number Price4-5440 $0.69
Gutter Screws With 5" Ferrules
GUTTER SCREWS With
5” Ferrules These 7” long gutter screwsand 5” ferrules are made foruse with 5” gutter. Perfect forreplacing spikes that havepopped out. Use originalinstallation hole on existinginstallations. Comes with ¼”drive x #2 square bit for installing screws. There are10 screws and ferrules perpackage. We stock white only.
Part Number Price4-5450 $9.09
Zip-it Anchor
ZIP-IT ANCHOR This #8 self-drilling plastic anchor is ideal forhanging heavy items on drywall board. May use with #6 or #8 screw. Inside of head is cut for Philips or slotted screwdriver. Anchors are white or natural color. Packaged 10 per plastic bag.
Part Number Price4-5454 $2.98
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 174
REGULATOR LP GAS
LOW PRESSURE ONLY
140,000 BTUH CAPACITY 1/4" F.P.T. INLET
3/8" F.P.T. OUTLET
Part Number Price4-6010 $6.89
TANK VALVE LP GAS
STANDARD VALVE POL x 3/4" #14 NGT
Part Number Description Price4-6030 TANKS UP TO 40 LBS $9.984-6032 FOR 100 LB TANKS $9.98
REGULATOR TEE Inverted Type
1/4" O.D. TUBE by 1/4" M.P.T.
Part Number Price4-6035 $1.80
TAILPIECE ASSEMBLY
FOR
LP GAS REGULATOR POL x 1/4" M.P.T.
Part Number Price4-6045 $3.49
PIGTAILS - LP GAS
POL TO 1/4" INVERTED FLARE COPPER TUBING WITH
BRASS FITTINGS
Part Number Description Price4-6070 15" LONG $7.694-6071 20" LONG $7.79
JIG SAW BLADES Assorted 5-Pack
U-shank fits Black & Decker, Skil, Craftsman, Milwaukee, DeWalt,Makita, Ryobie and Porter Cable saws.Three blades are for wood cutting; one 4” blade with 10 tpi for clean smoothcuts, one 4” blade with 6 tpi for faststraight cuts and one wood cuttingscroll blade 2-3/4” with 12 tpi. Two blades for metal cutting; one 2-3/4” blade with 24 tpi for metal under 1/8”thick and one blade 2-3/4” with 14 tpi for metal over 1/8” thick. All bladesare made of high carbon steel withcobalt cutting edges.
Part Number Price4-7030 $6.98
RECIPROCATING SAW BLADE
IVY CLASSIC BRAND
This 6” long metal cutting blade has 18TPI (teeth per inch). Cuts metal 18gauge to 1/8” thick. Fits all 1/2” shankreciprocating saws. Has bi-metal cobalt cutting edge with 65-67 Rockwell hardness.
Part Number Price4-7032 $3.69
RECIPROCATING SAW BLADE
IVY CLASSIC BRAND
This 6” long wood, nail embedded wood and composition materialscutting blade has 6 TPI (teeth per inch). Fits all 1/2” shank reciprocating saws.Has bi-metal cobalt cutting edge with65-67 Rockwell hardness.
Part Number Price4-7036 $3.69
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 175
HOLE SAW The original patented high speed hole sawwith handy built-in arbor. Guaranteed to cutwood, plastic, or any machineable metal. Usewith pilot drill bit shown this page.
Part Number Description Price4-7000 1" DIAMETER $9.984-7001 2-1/8" DIAMETER $15.89
INSTALLATION KIT DOOR LOCKS WOOD DOORS
Door lock installation kit for use on wood doors 1-3/8” or 1-3/4” thick. Comes with adjustable molded plastic guide template foreasy and exact drilling. Use template for 2-3/8” and 2-3/4” backsets. Has 1” and 2-3/4” diameter wood hole saws with arbor &pilot drill bit that fits both hole saws. May use with entry locksand/or deadbolt locks. Instructions come with installation kit.
Part Number Price4-7002 $10.98
INSTALLATION KIT DOOR LOCKS
BI-METAL DOORS
Bi-metal installation kit for metal or wood doors 1-3/8” or 1-3/4” thick. Comes with adjustable molded plastic guide template foreasy and exact drilling. Use template for 2-3/8” and 2-3/4” backsets. Includes 1” and 2-1/8” diameter bi-metal hole saws witharbor & pilot drill bit that fits both hole saws. May use with entrylocks and/or deadbolt locks. Instructions come with installation kit.
Part Number Price4-7004 $16.98
PILOT BIT FOR HOLE SAW 1/4" diameter bit is made of high speed steel.
Part Number Price4-7005 $3.05
SCRAPER Razor Blade Retractable
Scrapes and cleans paint from glass, tile and metal. Comes withone high carbon steel .009" thick single edge blade.
Part Number Price4-7020 $2.98
RAZOR BLADES Single Edge
High Carbon Steel .009" thick industrial quality high carbon steel single edge blades are individually wrapped. Comes 10 to a package.
Part Number Price4-7022 $1.72
HUB PULLER Blower Wheel Fan
Blade This heavy duty hub puller isideal for pulling hub styleblower wheels and fan blades.Comes complete with four pullfingers and shaft alignmenttool. Fine threads provide foradditional torque and pullingpower.
Part Number Price4-7025 $34.95
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 176
Copper Tubing
TUBE CUTTER
ECONOMY GRADE ALL METAL BODY
Cuts from 1/8" to 1-1/8" tubing size. Part Number Price4-3348 $7.98
Copper Tubing, Midget With Rollers
TUBE CUTTER MIDGET
With Rollers
Cuts from 1/8" to 7/8" O.D. tubing.
Part Number Price4-3349 $5.25
TENSIONING TOOL
For Nylon Ties
Fits all standard and heavy duty ties.Provides proper tightness and trimsexcess materials flush.
Part Number Price4-3350 $29.95
Pressure Test Kit
PRESSURE TEST KIT
Comes with two steel-case pressuregauges, one is 0-30 psi, the other 0-100 psi. Gauges have unbreakable plasticfaces, 1/4"brass m.p.t. connection. Brassmanifold has 3/4" f.p.t. connection oneend with brass air valve on other end.For testing water piping, sewer systemand/or gas piping.
Part Number Price4-3311 $15.98
Water Pressure Test Gauge
PRESSURE TEST KIT
This water pressure test gauge has a metal casing with a unbreakable plastic face. Readings from 0 to 300 PSI. Has a 3/4" female hose adapter made of brass.
Part Number Price4-3352 $9.99
CARPENTERS PENCIL
Made of wood, has gray lead, 7 inches long.
Part Number Price4-7010 $0.98
MARKING FLAGS
Flag is made of 2.5" x 3.5" orange plastic attached to a 21" long steel shaft.
Sold 100 per bundle.
Part Number Price4-7014 $6.98
ELEMENT WRENCH (Heavy Duty)
Fits all screw-in water heater elements. Fits all 1-1/2 hex nuts. Heavy duty zinc plated steel.
Part Number Price4-3525 $5.45
*Prices are Subject to Change without Notice.*
(336) 744-9071 Winston-Salem, NC Toll Free Phone (800) 836-3627Page 177