365 Operator and Parts Manual - Tennant Co

365

MM173

This manual is furnished with each new TENNANTr Model . It provides necessary operating and preventivemaintenance instructions. Read this manual completely and understand the machine before operating or servicingit.

This manual covers all machine variations and standard accessories. The instruction portion of the manualconsists of the Specification, Operation, Maintenance, and Appendix sections. The parts portion consists of theStandard Model Parts; LPG Parts; Accessories; Hydraulic Components; Engine Parts; and Cross Reference; andCustomer Documents sections.

All right side and left side references to the machine are determined by facing the direction of forward travel. Allhardware considered to be of a common nature or locally available has been omitted from the parts sections. Beaware that this machine may contain metric hardware. Make sure you use equivalent hardware whenreplacement becomes necessary.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

D The machine is operated with reasonable care.D The machine is maintained regularly -- per the maintenance instructions provided.D The machine is maintained with Tennant Company supplied or equivalent parts.

Parts and supplies may be ordered by phone or mail from any Tennant Company parts and service center,distributor, or from any of the Tennant Company subsidiaries. Before ordering parts or supplies, be sure to haveyour machine model number and serial number handy. Fill out the data block below for future reference. Thetelephone numbers, telex numbers, mailing addresses, and locations of those outlets are listed in the CustomerDocuments section of the manual.

MACHINE DATA

Please fill out at time of installation.

Machine Serial Number --

Engine Serial Number --

Sales Representative --

Customer Number --

Date of Installation --

Manual Number -- MM173

Revision: 09

Published: 6--9003873

Trademark Registered in: Austria, Benelux, Denmark, England, France, Germany, Italy, Spain, Switzerland,United States, Argentina, Australia, Canada, Japan, Mexico, Sweden, by TENNANT COMPANY, Minneapolis,Minnesota, U.S.A.

Acknowledgements: Technical information and/or illustrations supplied by Ford Motor Company; EatonCorporation, Hydraulics Division.

Copyright 1986, 1987, 1988, 1989, 1990 Tennant Company, Printed in U.S.A.

ABOUT THIS MANUAL

a365 MM173 (3--90)

ABOUT THIS MANUAL

The machine manual that you received with yourTENNANT machine contains valuable informationabout the operation and maintenance, and numeroussections filled with TENNANT part numbers for therepair of the machine. Please read through thissection titled ABOUT THIS MANUAL to becomefamiliar with the contents of the machine manual,making the information you are looking for easier tofind.

The machine manual consists of several sections ofreference information, and the remainder contain partnumber information for ordering repair parts for themachine. Each section has a shaded bar at the top ofthe page with the name of that section. Just as thissection has the title ABOUT THIS MANUAL on thetop of each page. This way you can tell which sectionyou are in at all times.

REFERENCE SECTIONS

The reference information sections of the manual are;General Information, Specifications, Operation,Maintenance, and Appendix.

GENERAL INFORMATION -- The GeneralInformation section of the manual contains the safetyprecautions, the location of the safety labels on themachine, and a table of contents of the entire manual.The Safety Precautions are an overview of the safetymeasures to be observed when operating andmaintaining your machine. The location of the safetylabels show the mounting location of the safety labelsfor use in the replacement of the labels. The table ofcontents in this section is a list of all the table ofcontents that appear in the front of each section in themanual. This can be used for easy reference to locateinformation in a particular section of the manual.

SPECIFICATIONS -- The Specifications section of themanual contains machine specification informationuseful in the operation and maintenance of themachine. This section gives you specificationinformation on the engine, electric motors, brakesystem, hydraulics, fluid capacities, and machineweight to mention a few. The section also has aillustration of the top and side view of the machinewith the height and width dimensions displayed.

OPERATION -- The Operation section of the manualcontains information needed to operate the machine.This section will list the controls and instruments onthe machine, overview the machine operation, and tellyou how to transport and store the machine.

MAINTENANCE -- The Maintenance section containsinformation on the suggested maintenanceprocedures and adjustments to keep your machine intop operating condition. The section includes aMaintenance Chart listing the maintenance scheduleand the areas of the machine to be addressed. Eachsubject of maintenance is covered in more detail insuch areas as Lubrication, Hydraulics, Engine, andElectrical System.

APPENDIX -- The Appendix contains hardware andhydraulic information. Standard hardware torques andidentification information is included, plus hydraulictorques if your machine is hydraulically controlled.

PART SECTIONS

The remaining sections of the manual contain partnumber information for ordering repair parts for yourmachine. The manual contains part numberinformation on every type of machine model availablein the model size of your particular machine.Therefore there will be part number information inyour manual you will not need to refer to whenwanting to place an order.

The main thing you need to know about your machineis what type of model is it. Is the machine powered byan engine or batteries? If the machine has an engine,is it fueled from gasoline, LPG, or gasoline? If it is amid-sized or larger sweeper, is it multi-level or lowdump? For the scrubbers, is it SRSr or standard.Determining this information about your machine willhelp guide you through the separate parts sections tofind the repair part you need.

ABOUT THIS MANUAL

365 MM173 (3--90)b

The smaller line of sweeper and scrubbers have lesscomplicated part section arrangement, and are easierto find your way through the parts sections. The largermachines can have quite a variety of model typeswhich significantly increases the size to the machinemanual. Because of this, on the larger machine wemade the first part section, Section 5, a part sectionwhich contains parts common to all type of themachine. If the machine has an engine, this sectioncontains parts information on a gasoline poweredmachine.

The remaining sections contain only parts informationwhich is unique to that particular machine type, suchas unique diesel parts on the machine, or uniqueSRSr parts. Knowing the machine model type youhave is important when searching for that partinformation you need for ordering repair parts. Start inthat unique section first when looking for a part, thengo to the first parts section, Section 5, if the part can’tbe found in the unique section.

MACHINE SERIAL NUMBERS

When a design change takes place to a machine, thechanges are indicated in the parts sections withmachine serial numbers. Know the serial number ofyour machine which can be found on the machinedata plate mounted on the machine. Record thisnumber on the inside front cover of your manual alongwith your customer number.

Machine number usage is recorded in the MachineSerial Number column of the parts lists in the partssections of the manual. If the machine serial numbercolumn lists zeros on the left side of the dash, thenthis part is used on all machines; such as(000000-- ).

If the column lists zeros on the left of the dash and anumber on the right of the dash, then the part is usedon machines up to and including that machine serialnumber; such as (00000--002345).

For parts that are used on machines beginning at andcontinuing on from a certain serial number, thecolumn would list a serial number on the left of thedash and have blank spaces on the right side of thedash; such as (002346-- ). This part would be usedon machines starting with that machine serial numberand greater.

Finally, parts can be used on machines with serialnumbers in a certain block of numbers. In thissituation there is a serial number on the left and rightside of the dash. The part is then used on a machinewith a serial number starting at the number on the leftand up to and including the number on the right; suchas (002346--008900).

PARTS ASSEMBLIES

A part assembly has parts within the assembly, suchas a parking brake consisting of other smaller parts.What parts are contained in a part assembly can bedetermined by an indentation arrangement in thedescription column of the parts lists.

Here is an example of a part assembly, in this casewe will use the parking brake mentioned previously:

MachineSerial Number Description Qty.(000000-- ) Parking Brake 1(000000-- ) Pin, Roll 1(000000-- ) Link 1(000000-- ) Spring, Compression 1(000000-- ) Pin, Roll 1(000000-- ) Support 1(000000-- ) Lever, Release 1(000000-- ) Rod, Parking Brake 1(000000-- ) Washer, 0.50” 3

In this example, the parts whose descriptions areindented under the parking brake are all parts of theparking brake. When you order the parking brake youwill receive all the parts listed under it. You also canorder any of the individual parts listed under theparking brake if it is the only part you need.

ABOUT THIS MANUAL

c365 MM173 (3--90)

SUPPLIER COMPONENT BREAKDOWNS

TENNANT purchases certain components of themachine from suppliers. Some of these componentsare engines, hydraulic pumps and motors, electricmotors, and solution pumps.

For those purchased components that are repairable,lists of parts for them appear in the later part of theparts sections. These are the supplier breakdowns.The engine breakdown contains both supplier andTENNANT parts numbers for repair parts.Breakdowns for hydraulic and electrical componentshave TENNANT part numbers for the partsTENNANT supplies. The serial numbers listed in anyof the parts lists in these sections is a serial numberthe manufacturer uses to identify design changes intheir particular component.

ORDERING REPAIR PARTS

Once you have located a part to order, there areseveral things you need to have to place the order. Atthe beginning of each parts section is an OrderingRepair Parts page which lists the information you willneed to place your order. Review this list beforeplacing the order.

ABOUT THIS MANUAL

365 MM173 (3--90)d

GENERAL INFORMATION

i365 MM173 (3--90)

SAFETY PRECAUTIONS

The following symbols are used throughout thismanual as indicated in their descriptions:

WARNING: To warn of hazards or unsafepractices which could result in severe

personal injury or death.

FOR SAFETY: To identify actions which must befollowed for safe operation of equipment.

The following information signals potentiallydangerous conditions to the operator or equipment.Read this manual carefully. Know when theseconditions can exist. Locate all safety devices on themachine. Then take necessary steps to train machineoperating personnel. Report machine damage orfaulty operation immediately. Do not use the machineif it is not in proper operating condition.

FOR SAFETY:1. Do not operate machine:

-- Unless trained and authorized.-- Unless operation manual is read andunderstood.

-- In flammable or explosive areas unlessmodified for use in those areas.

-- In areas with possible falling objectsunless equipped with overhead guard.

2. Before starting machine:-- Check for fuel leaks (gasoline, LPG).-- Make sure all safety devices are in placeand operate properly.

-- Check brakes and steering for properoperation.

3. When starting machine:-- Keep foot on brake and directional pedalin neutral.

4. When using machine:-- Go slow on grades and slippery surfaces.-- Use care when backing machine.-- Do not carry riders on machine.-- Always follow safety and traffic rules.

5. Before leaving or servicing machine:-- Stop on level surface.-- Set parking brake.-- Turn off machine and remove key.

6. When servicing machine:-- Avoid moving parts. Do not wear loosejackets, shirts, or sleeves when workingon machine.

-- Use TENNANT supplied or equivalentreplacement parts.

WARNING: Engine emits toxic gases.Severe respiratory damage or asphyxiation

can result. Provide adequate ventilation. Consultwith your regulatory agency for exposure limits.Keep engine properly tuned.

WARNING: Machine can emit excessivenoise. Consult with your regulatory agency

for exposure limits. Hearing loss can result. Wearhearing protection.

WARNING: Machine hopper lifts to 108 in(2745 mm) when high dumping. Hopper can

hit overhead wires or object. Electrical shock orfalling debris can result. Be sure adequateclearance is available before raising hopper.

WARNING: Machine can have staticelectricity charge. When pouring fuel, spark

can ignite fuel causing fire or explosion. Connectwire attached to fuel can to machine to dischargespark before pouring fuel.

WARNING: Machine moves whendirectional pedal linkage is out of

adjustment. Severe personal injury or death canresult. If machine creeps when the directionalpedal is in neutral, adjust pedal linkage. Engageparking brake when stopped.

WARNING: Falling hopper. Engage hoppersupport bar before working under hopper.

WARNING: Batteries emit hydrogen gas.Explosion or fire can result. Keep flames

and sparks away. Keep covers open whencharging.

WARNING: Avoid contact with battery acid.Battery acid can cause severe burns. Wash

immediately and get medical attention if contactwith acid occurs.

GENERAL INFORMATION

365 MM173 (3--90)ii

WARNING: Fuel vapor is present whenservicing fuel system. Fire or explosion can

result. Keep flames and sparks away.

WARNING: Machine moves whendirectional pedal linkage is out of

adjustment. Severe personal injury or death canresult. If machine creeps when the directionalpedal is in neutral, adjust pedal linkage. Engageparking brake when stopped.

WARNING: Machine is unstable on jack.Jack machine up at designated locations

only. Block machine up with jack stands.

WARNING: Machine is unstable on jack.Block machine tires before jacking machine

up.

WARNING: Leaking hydraulic fluid underpressure can penetrate skin. Severe

infection or death can result. Do not use body tolocate leak. Use cardboard to locate leak.

WARNING: Hot engine coolant. Scaldingcan result. Do not open radiator cap or

service cooling system until radiator and engineis cool to the touch.

WARNING: Air or water under pressure.Severe eye or ear injury can result. Wear

eye and ear protection.

WARNING: LPG fuel is very cold. Frostbitecan result. Wear gloves when connecting

or disconnecting LPG hoses.

WARNING: Stay clear of hopper lift armswhen they are in motion.

GENERAL INFORMATION

iii365 MM173 (3--90)

The following safety labels are mounted on themachine in the locations indicated. If these or anylabels become damaged or illegible, install a newlabel in its place.

ENGINE FAN LABEL -- LOCATED ON RADIATORSHROUD.

05958

HOPPER SUPPORT BAR LABEL -- LOCATED ONHOPPER SUPPORT BAR AND ON EACH SIDE OFTHE HOPPER.

SAFETY LABEL -- LOCATED ON LEFT SIDE OFOPERATOR COMPARTMENT.

HOPPER CLEARANCE LABEL -- LOCATEDABOVE EACH FRONT WHEEL.

GENERAL INFORMATION

365 MM173 (3--90)iv

CONTENTS

PageGENERAL INFORMATION i. . . . . . . . . . . . . . . . .

SAFETY PRECAUTIONS i. . . . . . . . . . . . . . .

SPECIFICATIONS 1-1. . . . . . . . . . . . . . . . . . . . . . . .MACHINE SPECIFICATIONS 1-3. . . . . . . . . . . .

POWER TYPE 1-3. . . . . . . . . . . . . . . . . . . . . .POWER TRAIN 1-3. . . . . . . . . . . . . . . . . . . . .STEERING 1-3. . . . . . . . . . . . . . . . . . . . . . . . .HYDRAULIC SYSTEM 1-3. . . . . . . . . . . . . . .BRAKING SYSTEM 1-4. . . . . . . . . . . . . . . . .SUSPENSION SYSTEM 1-4. . . . . . . . . . . . .SYSTEM FLUID CAPACITIES 1-4. . . . . . . .GENERAL MACHINE

DIMENSIONS/CAPACITIES 1-4. . . . . . .MACHINE WEIGHTS 1-4. . . . . . . . . . . . . . . .GENERAL MACHINE PERFORMANCE 1-4

MACHINE DIMENSIONS 1-5. . . . . . . . . . . . . . . .

OPERATION 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PREPARATION FOR OPERATION 2-3. . . . . . .

AFTER UNLOADING AND BEFOREOPERATING THE MACHINE: 2-3. . . . . .

OPERATION OF CONTROLS 2-4. . . . . . . . . . .MACHINE COMPONENTS 2-4. . . . . . . . . . .INSTRUMENT PANEL SYMBOLS 2-5. . . . .CONTROLS AND INSTRUMENTS 2-6. . . .BRAKE PEDAL 2-7. . . . . . . . . . . . . . . . . . . . .DIRECTIONAL PEDAL 2-7. . . . . . . . . . . . . . .PARKING BRAKE LEVER 2-7. . . . . . . . . . . .OPERATOR SEAT 2-7. . . . . . . . . . . . . . . . . . .HAZARD LIGHT SWITCH 2-8. . . . . . . . . . . .THROTTLE LEVER 2-8. . . . . . . . . . . . . . . . . .THROTTLE SWITCH 2-8. . . . . . . . . . . . . . . .ENGINE CHOKE LEVER 2-8. . . . . . . . . . . . .ENGINE CHOKE KNOB 2-8. . . . . . . . . . . . . .CLOGGED FILTER INDICATOR 2-8. . . . . . .VACUUM FAN AND FILTER SHAKER

SWITCH 2-8. . . . . . . . . . . . . . . . . . . . . . . . .II SPEEDt SWITCH 2-8. . . . . . . . . . . . . . . . .HOPPER DOOR SWITCH 2-8. . . . . . . . . . . .HOPPER SWITCH 2-9. . . . . . . . . . . . . . . . . .SIDE BRUSH POSITION LEVER 2-9. . . . . .MAIN BRUSH POSITION LEVER 2-9. . . . .MAIN BRUSH HEIGHT ADJUSTMENT

KNOB 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . .STEERING TILT LEVER 2-9. . . . . . . . . . . . .ENGINE HOUR METER 2-10. . . . . . . . . . . . . .ENGINE OIL PRESSURE GAUGE 2-10. . . .ENGINE COOLANT TEMPERATURE

GAUGE 2-10. . . . . . . . . . . . . . . . . . . . . . . . .STEERING WHEEL 2-10. . . . . . . . . . . . . . . . .

PageFUEL LEVEL GAUGE 2-10. . . . . . . . . . . . . . . .VOLTAGE GAUGE 2-10. . . . . . . . . . . . . . . . . .OPERATING LIGHTS SWITCH 2-10. . . . . . .IGNITION SWITCH 2-10. . . . . . . . . . . . . . . . . .HOPPER SUPPORT BAR 2-11. . . . . . . . . . . .

TO ENGAGE HOPPERSUPPORT BAR 2-11. . . . . . . . . . . . . . .

TO DISENGAGE HOPPERSUPPORT BAR 2-11. . . . . . . . . . . . . . .

CIRCUIT BREAKERS 2-12. . . . . . . . . . . . . . . .MACHINE OPERATION 2-13. . . . . . . . . . . . . . . . .

NORMAL SWEEPING OPERATION 2-13. . .PRE-START CHECKLIST 2-13. . . . . . . . . .TO START MACHINE 2-13. . . . . . . . . . . . .TO SWEEP 2-14. . . . . . . . . . . . . . . . . . . . . .TO DUMP HOPPER 2-14. . . . . . . . . . . . . .POST OPERATION CHECKLIST --

ENGINE OPERATING 2-15. . . . . . . . . .TO STOP MACHINE 2-15. . . . . . . . . . . . . .POST OPERATION CHECKLIST --

ENGINE STOPPED 2-15. . . . . . . . . . . .OPERATION ON GRADES 2-15. . . . . . . . . . .MACHINE TROUBLESHOOTING 2-16. . . . .

ACCESSORIES OPERATION 2-17. . . . . . . . . . .VACUUM WAND ACCESSORY 2-17. . . . . . .

TO OPERATE VACUUM WAND 2-17. . . .CAB PRESSURIZER 2-18. . . . . . . . . . . . . . . .

TRANSPORTING MACHINE 2-19. . . . . . . . . . . . .PUSHING OR TOWING MACHINE 2-19. . . .MACHINE JACKING 2-19. . . . . . . . . . . . . . . . .

TO JACK UP MACHINE 2-19. . . . . . . . . . .MACHINE TIE-DOWNS 2-20. . . . . . . . . . . . . .

MACHINE STORAGE 2-21. . . . . . . . . . . . . . . . . . .STORING MACHINE 2-21. . . . . . . . . . . . . . . .

MAINTENANCE 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . .RECOMMENDED FIRST 50-HOUR

MACHINE INSPECTION 3-3. . . . . . . . . . . . .MAINTENANCE CHART 3-4. . . . . . . . . . . . . . . .LUBRICATION 3-6. . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .HOPPER PIVOT 3-6. . . . . . . . . . . . . . . . . . . .SIDE BRUSH PIVOT 3-6. . . . . . . . . . . . . . . .REAR WHEEL SUPPORT 3-7. . . . . . . . . . . .STEERING CYLINDER ENDS 3-7. . . . . . . .FRONT WHEEL BEARINGS 3-7. . . . . . . . . .

GENERAL INFORMATION

v365 MM173 (3--90)

PageHYDRAULICS 3-8. . . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID 3-8. . . . . . . . . . . . . . . . .HYDRAULIC FLUID RESERVOIR 3-8. . . . .

TO DRAIN HYDRAULIC FLUIDRESERVOIR 3-9. . . . . . . . . . . . . . . . . .

TO FILL HYDRAULIC FLUIDRESERVOIR 3-9. . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID RESERVOIRBREATHER 3-10. . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID FILTER 3-10. . . . . . . . . .TO REPLACE HYDRAULIC

FLUID FILTER ELEMENT 3-10. . . . . .DIRECTIONAL PEDAL 3-11. . . . . . . . . . . . . . .

TO ADJUST DIRECTIONALPEDAL LINKAGE 3-11. . . . . . . . . . . . . .

HYDRAULIC FLUID LEAKS 3-13. . . . . . . . . .HYDRAULIC SCHEMATIC 3-14. . . . . . . . . . . .HYDRAULIC SYSTEM

TROUBLESHOOTING 3-15. . . . . . . . . . . .ENGINE 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE LUBRICATION 3-17. . . . . . . . . . . . . .COOLING SYSTEM 3-17. . . . . . . . . . . . . . . . .AIR INTAKE SYSTEM 3-18. . . . . . . . . . . . . . .

AIR FILTER SERVICE INDICATOR 3-18.AIR FILTER 3-18. . . . . . . . . . . . . . . . . . . . . .TO REPLACE AIR FILTER ELEMENT3-19

FUEL SYSTEM -- GASOLINE 3-21. . . . . . . . .FUEL FILTER 3-21. . . . . . . . . . . . . . . . . . . .CARBURETOR 3-21. . . . . . . . . . . . . . . . . . .

FUEL SYSTEM -- LPG 3-21. . . . . . . . . . . . . . .LPG FUEL SYSTEM 3-21. . . . . . . . . . . . . .FUEL TANKS 3-22. . . . . . . . . . . . . . . . . . . .TO CHANGE AN LPG FUEL TANK 3-23.FUEL FILTER LOCK 3-23. . . . . . . . . . . . . .VAPORIZER-REGULATOR 3-23. . . . . . . .CARBURETOR 3-24. . . . . . . . . . . . . . . . . . .OIL PRESSURE SWITCH 3-24. . . . . . . . .

LPG FUEL TROUBLESHOOTING 3-24. . . . .GOVERNOR (For machines below serialnumber 007000) 3-25. . . . . . . . . . . . . . . . . . . . .

TO ADJUST GOVERNOR (For machinesbelow serial number 007000) 3-25. . . .

GOVERNOR (For machines serial number007000 and above) 3-25. . . . . . . . . . . . . . .

PageELECTRICAL SYSTEM 3-26. . . . . . . . . . . . . .

SPARK PLUGS 3-26. . . . . . . . . . . . . . . . . .DISTRIBUTOR (For machines below

serial number 007000) 3-26. . . . . . . . . .TO REPLACE IGNITION POINTS (For

machines below serialnumber 007000) 3-27. . . . . . . . . . . . . . .

DISTRIBUTOR IGNITION TIMING (Formachines below serial

number 007000) 3-28. . . . . . . . . . . . . . .TO CHECK AND ADJUST DISTRIBUTOR

IGNITION TIMING (For machinesbelow serial number 007000) 3-28.

ENGINE IGNITION TIMING (Formachines serial number 007000and above) 3-29. . . . . . . . . . . . . . . . . . . .

CYLINDER HEAD 3-29. . . . . . . . . . . . . . . . . . .CYLINDER HEAD 3-29. . . . . . . . . . . . . . . .VALVE TAPPET CLEARANCE 3-30. . . . .

CRANKCASE VENTILATION SYSTEM 3-30.TUNE-UP CHART 3-30. . . . . . . . . . . . . . . . . . .

ELECTRICAL SYSTEM 3-31. . . . . . . . . . . . . . . . .BATTERY 3-31. . . . . . . . . . . . . . . . . . . . . . . . . .ELECTRICAL SCHEMATIC (For machines

below serial number 007000) 3-32. . . . . . .ELECTRICAL SCHEMATIC (For machines

serial number 007000 and above) 3-34. . .BELTS AND CHAINS 3-36. . . . . . . . . . . . . . . . . . .

ALTERNATOR BELT (For machines belowserial number 007000) 3-36. . . . . . . . . . . . .

ENGINE FAN BELT (For machines belowserial number 007000) 3-36. . . . . . . . . . . . .

ENGINE FAN BELT (For machines serialnumber 007000 and above) 3-36. . . . . . . .

STATIC DRAG CHAIN 3-36. . . . . . . . . . . . . . .DEBRIS HOPPER 3-37. . . . . . . . . . . . . . . . . . . . . .

HOPPER DUST FILTER 3-37. . . . . . . . . . . . . .TO REMOVE HOPPER

DUST FILTER 3-37. . . . . . . . . . . . . . . . .TO INSTALL HOPPER

DUST FILTER 3-38. . . . . . . . . . . . . . . . .THERMO-SENTRYt 3-38. . . . . . . . . . . . . . . .VACUUM FAN AND MAIN BRUSH

SHUT-OFF SWITCH 3-39. . . . . . . . . . . . . .DEBRIS HOPPER 3-39. . . . . . . . . . . . . . . . . . .

TO ADJUST HOPPER 3-39. . . . . . . . . . . .

GENERAL INFORMATION

365 MM173 (3--90)vi

PageBRUSHES 3-44. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAIN BRUSH 3-44. . . . . . . . . . . . . . . . . . . . . . .TO REPLACE MAIN BRUSH 3-44. . . . . . .TO CHECK AND ADJUST MAIN

BRUSH PATTERN 3-45. . . . . . . . . . . . .SIDE BRUSH 3-46. . . . . . . . . . . . . . . . . . . . . . .

TO REPLACE SIDE BRUSH 3-47. . . . . . .SKIRTS AND SEALS 3-49. . . . . . . . . . . . . . . . . . .

HOPPER LIP SKIRTS 3-49. . . . . . . . . . . . . . . .TO REPLACE HOPPER LIP SKIRTS 3-49

BRUSH DOOR SKIRTS 3-49. . . . . . . . . . . . . .TO REPLACE AND ADJUST BRUSH

DOOR SKIRTS 3-49. . . . . . . . . . . . . . . .REAR SKIRTS 3-50. . . . . . . . . . . . . . . . . . . . . .

TO REPLACE AND ADJUST REARSKIRTS 3-50. . . . . . . . . . . . . . . . . . . . . .

HOPPER SIDE SKIRTS 3-51. . . . . . . . . . . . . .TO REPLACE AND ADJUST HOPPER

SIDE SKIRTS 3-51. . . . . . . . . . . . . .MAIN BRUSH DOOR SEALS 3-52. . . . . . . . .HOPPER SEALS 3-52. . . . . . . . . . . . . . . . . . . .HOPPER DOOR SEALS 3-52. . . . . . . . . . . . .HOPPER COVER SEAL 3-53. . . . . . . . . . . . . .HOPPER VACUUM FAN SEAL 3-53. . . . . . . .

BRAKES AND TIRES 3-54. . . . . . . . . . . . . . . . . . .SERVICE BRAKES 3-54. . . . . . . . . . . . . . . . . .

TO BLEED THE BRAKES 3-54. . . . . . . . .PARKING BRAKES 3-54. . . . . . . . . . . . . . . . . .TIRES 3-55. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPENDIX 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .HARDWARE INFORMATION 4-3. . . . . . . . . . . .

STANDARD BOLT TORQUE CHART 4-3. .METRIC BOLT TORQUE CHART 4-3. . . . .BOLT IDENTIFICATION 4-3. . . . . . . . . . . . . .THREAD SEALANT AND LOCKING

COMPOUNDS 4-3. . . . . . . . . . . . . . . . . . .HYDRAULIC FITTING INFORMATION 4-4. . . .

HYDRAULIC TAPERED PIPE FITTING(NPT) TORQUE CHART 4-4. . . . . . . . . . .

HYDRAULIC TAPERED SEAT FITTING(JIC) TORQUE CHART 4-4. . . . . . . . . . . .

HYDRAULIC O--RING FITTING TORQUECHART 4-4. . . . . . . . . . . . . . . . . . . . . . . .

STANDARD PARTS 5-1. . . . . . . . . . . . . . . . . . . . . . .ORDERING REPAIR PARTS 5-3. . . . . . . . . . . .Fig. 1 -- Recommended General

Maintenance Items 5-4. . . . . . . . . .Fig. 2 -- Replacement Brushes 5-5. . . . . . . . . . .Fig. 3 -- Main Frame Group 5-6. . . . . . . . . . . . . .Fig. 4 -- Operators Compartment Group 5-8. . .Fig. 5 -- Engine Cover and Side

Panels Group 5-10. . . . . . . . . . . . . . .

PageFig. 6 -- Seat Group 5-12. . . . . . . . . . . . . . . . . . . .Fig. 7 -- Sheaves and Belts Group 5-13. . . . . . . .Fig. 8 -- Engine Fan and Alternator Group,

Distributorless (DIS) 5-14. . . . . . . . . . . .Fig. 9 -- Engine Group 5-16. . . . . . . . . . . . . . . . . .Fig. 10 -- Engine Group, Distributorless

(DIS) 5-18. . . . . . . . . . . . . . . . . . . . . .Fig. 11 -- Engine Flywheel and Mounting

Group, Distributorless (DIS) 5-20. .Fig. 12 -- Carburetor and Throttle Group 5-22. . .Fig. 13 -- Carburetor and Throttle Group,

Distributorless (DIS) 5-24. . . . . . . . .Fig. 14 -- Fuel Tank Group 5-26. . . . . . . . . . . . . . .Fig. 15 -- Fuel Tank Group 5-27. . . . . . . . . . . . . . .Fig. 16 -- Fuel Tank Group 5-28. . . . . . . . . . . . . . .Fig. 17 -- Air Cleaner and Hydraulic Filter

Group 5-29. . . . . . . . . . . . . . . . . . . . .Fig. 18 -- Air Cleaner and Hydraulic Filter

Group, Distributorless (DIS) 5-30. .Fig. 19 -- Radiator Group 5-31. . . . . . . . . . . . . . . .Fig. 20 -- Radiator Group, Distributorless

(DIS) 5-32. . . . . . . . . . . . . . . . . . . . . .Fig. 21 -- Vacuum Fan Group 5-34. . . . . . . . . . . . .Fig. 22 -- Hopper Lift Arms Group 5-36. . . . . . . . .Fig. 23 -- Hopper Assembly 5-38. . . . . . . . . . . . . .Fig. 24 -- Hopper Door Group 5-40. . . . . . . . . . . .Fig. 25 -- Muffler Group 5-41. . . . . . . . . . . . . . . . . .Fig. 26 -- Muffler Group, Distributorless

(DIS) 5-42. . . . . . . . . . . . . . . . . . . . . .Fig. 27 -- Side Brush Cables Group 5-43. . . . . . .Fig. 28 -- Side Brush Group 5-44. . . . . . . . . . . . . .Fig. 29 -- Main Brush Lift and Drive Group 5-46.Fig. 30 -- Brakes Group 5-48. . . . . . . . . . . . . . . . . .Fig. 31 -- Parking Brakes Group 5-50. . . . . . . . . .Fig. 32 -- Front Wheel Group 5-52. . . . . . . . . . . . .Fig. 33 -- Rear Wheel Assembly 5-53. . . . . . . . . .Fig. 34 -- Rear Wheel Support Group 5-54. . . . . .Fig. 35 -- Steering Column Group 5-56. . . . . . . . .Fig. 36 -- Instrument Panel Group 5-58. . . . . . . . .Fig. 37 -- Battery Group 5-59. . . . . . . . . . . . . . . . .Fig. 38 -- Wire Harnesses Group 5-60. . . . . . . . . .Fig. 39 -- Wire Harnesses Group 5-62. . . . . . . . . .Fig. 40 -- Directional Control Group 5-64. . . . . . .Fig. 41 -- Directional Control Group 5-66. . . . . . .Fig. 42 -- Hydraulic Pumps Group 5-68. . . . . . . . .Fig. 43 -- Hydraulic Pumps Group 5-69. . . . . . . . .Fig. 44 -- Hydraulic Control Valve Group 5-70. . .Fig. 45 -- Hydraulic Reservoir Group 5-72. . . . . .Fig. 46 -- Hydraulic Hoses Group 5-74. . . . . . . . .Fig. 47 -- Hydraulic Hoses Group 5-76. . . . . . . . .Fig. 48 -- Labels Group 5-78. . . . . . . . . . . . . . . . . .

GENERAL INFORMATION

vii365 MM173 (3--90)

PageLPG PARTS 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ORDERING REPAIR PARTS 6-3. . . . . . . . . . . .Fig. 1 -- Carburetor and Fuel Tank

Group, LPG 6-4. . . . . . . . . . . . . . . .Fig. 2 -- Engine Group, Distributorless

(DIS), LPG 6-6. . . . . . . . . . . . . . . . .

ACCESSORIES 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . .ORDERING REPAIR PARTS 7-3. . . . . . . . . . . .Fig. 1 -- Revolving Light Kit, Shroud 7-4. . . . . .Fig. 2 -- Revolving Light Kit, Overhead

Guard 7-5. . . . . . . . . . . . . . . . . . . . .Fig. 3 -- Revolving Light Kit, Cab 7-6. . . . . . . . .Fig. 4 -- Flashing Light Kit, Shroud 7-7. . . . . . . .Fig. 5 -- Flashing Light Kit, Overhead

Guard 7-8. . . . . . . . . . . . . . . . . . . . .Fig. 6 -- Flashing Light Kit, Cab 7-9. . . . . . . . . .Fig. 7 -- Overhead Guard Kit 7-10. . . . . . . . . . . . .Fig. 8 -- Air Filter Safety Kit 7-11. . . . . . . . . . . . . .Fig. 9 -- Fire Extinguisher Kit 7-12. . . . . . . . . . . . .Fig. 10 -- Protectoseal Fuel Tank Cap Kit 7-12. .Fig. 11 -- Solid Tire Kit 7-13. . . . . . . . . . . . . . . . . . .Fig. 12 -- Cab Kit 7-14. . . . . . . . . . . . . . . . . . . . . . .Fig. 13 -- Cab Door Assembly 7-16. . . . . . . . . . . .Fig. 14 -- Cab Pressurizer Group 7-18. . . . . . . . .Fig. 15 -- Wire Harnesses Group, Cab 7-19. . . . .Fig. 16 -- Cab Heater Group 7-20. . . . . . . . . . . . . .Fig. 17 -- Cab Heater Electrical Group 7-22. . . . .Fig. 18 -- Cab Heater Group 7-24. . . . . . . . . . . . . .Fig. 19 -- Cab Heater Electrical Group 7-26. . . . .Fig. 20 -- Vacuum Wand Kit 7-28. . . . . . . . . . . . . .Fig. 21 -- Heavy Duty Bumper Group 7-30. . . . . .Fig. 22 -- Urethane Tire Kit 7-31. . . . . . . . . . . . . . .

PageHYDRAULIC COMPONENTS 8-1. . . . . . . . . . . . . . .

ORDERING REPAIR PARTS 8-3. . . . . . . . . . . .Fig. 1 -- Hydraulic Pump Breakdown,

02634 8-4. . . . . . . . . . . . . . . . . . . . .Fig. 2 -- Hydraulic Pump Breakdown,

02704 8-6. . . . . . . . . . . . . . . . . . . . .Fig. 3 -- Hydraulic Pump Breakdown,

13101 8-8. . . . . . . . . . . . . . . . . . . . .Fig. 4 -- Hydraulic Motor Breakdown,






27800 8-14. . . . . . . . . . . . . . . . . . . . .Fig. 10 -- Hydraulic Valve Breakdown,

57982 8-15. . . . . . . . . . . . . . . . . . . . .Fig. 11 -- Hydraulic Solenoid Valve

Breakdown, 13104 8-16. . . . . . . . . .Fig. 12 -- Hydraulic Cylinder Breakdown,

04464 8-17. . . . . . . . . . . . . . . . . . . . .Fig. 13 -- Hydraulic Cylinder Breakdown,

04430 8-18. . . . . . . . . . . . . . . . . . . . .

GENERAL INFORMATION

365 MM173 (3--90)viii

PageENGINE PARTS, GASOLINE, LPG 9-1. . . . . . . . . .

ORDERING REPAIR PARTS 9-3. . . . . . . . . . . .Fig. 1 -- Cylinder Block, Head, and

Manifolds Group 9-4. . . . . . . . . . . .Fig. 2 -- Crankshaft Group 9-5. . . . . . . . . . . . . . .Fig. 3 -- Valves and Valve Cover Group 9-6. . . .Fig. 4 -- Camshaft Group 9-8. . . . . . . . . . . . . . . .Fig. 5 -- Piston and Connecting

Rod Group 9-9. . . . . . . . . . . . . . . . .Fig. 6 -- Oil Pump, Filter, and PCV

Group 9-10. . . . . . . . . . . . . . . . . . . . .Fig. 7 -- Water Pump and Thermostat

Group 9-12. . . . . . . . . . . . . . . . . . . . .Fig. 8 -- Distributor and Spark Plugs

Group 9-13. . . . . . . . . . . . . . . . . . . . .Fig. 9 -- Gasket Kits Group 9-14. . . . . . . . . . . . . . .

ENGINE PARTS, DIS, GASOLINE, LPG 10-1. . . . .ORDERING REPAIR PARTS 10-3. . . . . . . . . . . .Fig. 1 -- Cylinder Head, Valves Group 10-4. . . . .Fig. 2 -- Cylinder Block Group 10-6. . . . . . . . . . . .Fig. 3 -- Camshaft and Valve Control

Group 10-8. . . . . . . . . . . . . . . . . . . . .Fig. 4 -- Crankshaft and Piston Group 10-10. . . . .Fig. 5 -- Oil Pump and Oil Pan Group 10-12. . . . .Fig. 6 -- Intake Manifold Group 10-14. . . . . . . . . . .Fig. 7 -- Front Cover Assembly Group 10-15. . . . .Fig. 8 -- Water Pump Group 10-16. . . . . . . . . . . . .Fig. 9 -- Distributorless Ignition Group 10-17. . . . .Fig. 10 -- Gaskets Group 10-18. . . . . . . . . . . . . . . .Fig. 11 -- Flywheel Group 10-19. . . . . . . . . . . . . . . .

SPECIFICATIONS

1-1365 MM173 (3---90)

SECTION 1CONTENTS

PageMACHINE SPECIFICATIONS 1-3. . . . . . . . . . . . . . .

POWER TYPE 1-3. . . . . . . . . . . . . . . . . . . . . . . . .POWER TRAIN 1-3. . . . . . . . . . . . . . . . . . . . . . . .STEERING 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .HYDRAULIC SYSTEM 1-3. . . . . . . . . . . . . . . . . .BRAKING SYSTEM 1-4. . . . . . . . . . . . . . . . . . . .SUSPENSION SYSTEM 1-4. . . . . . . . . . . . . . . .SYSTEM FLUID CAPACITIES 1-4. . . . . . . . . . .GENERAL MACHINE

DIMENSIONS/CAPACITIES 1-4. . . . . . . . . .MACHINE WEIGHTS 1-4. . . . . . . . . . . . . . . . . . .GENERAL MACHINE PERFORMANCE 1-4. . .

MACHINE DIMENSIONS 1-5. . . . . . . . . . . . . . . . . . .

SPECIFICATIONS

365 MM173 (3---90)1-2

SPECIFICATIONS

1-3365 MM173 (3---90)

MACHINE SPECIFICATIONS

POWER TYPE

Engine for machine below serial number 007000Type -- pistonIgnition -- breaker--type sparkCycle -- 4Aspiration -- naturalCylinders -- 4Bore -- 3.19 in (81 mm)Stroke -- 3.06 in (78 mm)Displacement -- 98 cu in (1600 cc)Net power -- 35 hp (26 kw) @ 2350 rpm governed

47.5 hp (35 kw) @ 3600 rpm maximumFuel -- gasoline, 91 RON octane minimum, unleaded

or LPGCooling system -- water/ethylene glycol antifreezeElectrical system -- 12 V nominal, 37 A alternator

Engine for machine serial number 007000 and aboveType -- pistonIgnition -- breaker--type sparkCycle -- 4Aspiration -- naturalCylinders -- 4Bore -- 2.91 in (74 mm)Stroke -- 2.97 in (75 mm)Displacement -- 79 cu in (1300 cc)Net power -- 29 hp (21.6 kw) @ 2400 rpm governed

53.7 hp (40 kw) @ 4000 rpm maximumFuel -- gasoline, 87 octane minimum, unleaded or

LPGCooling system -- water/ethylene glycol antifreezeElectrical system -- 12 V nominal, 37 A alternator

POWER TRAIN

Propelling -- hydraulic drive motor driven, rear wheelMain brush -- hydraulic drive motor drivenSide brush -- hydraulic drive motor drivenVacuum fan -- hydraulic drive motor driven

STEERING

Type -- rear wheel, hydraulic cylinder and rotaryvalve controlled

Power source -- hydraulic accessory pumpEmergency steering -- manual

HYDRAULIC SYSTEM

Function -- operates propelling, hopper lift, steering,main brush drive, side brush drive, vacuum fandrive

Control valve, main brush, side brush, lift cylinders --open center, solenoid operated

Control valve, steering -- open center type, rotary,non--load reacting

Pump, propelling -- variable displacement pistontype, 1.24 cu in (20 cc) maximum displacementper revolution, 11.4 gpm (43 L/min) @ 2350 rpm

Propelling system relief pressure -- 4000 psi (27,850kPa)

Pump, accessories -- gear type, 1.20 cu in(20 cc) displacement, 9.8 gpm (37 L/min)@ 2350 rpm

Side brush system relief pressure -- 1200 psi (8275kPa)

Steering system relief pressure -- 500 psi (3450 kPa)

Main brush and vacuum fan system relief pressure --2300 psi (15,860 kPa)

Lifting cylinders system relief pressure -- 2300 psi(15,860 kPa)

Motor, propelling -- internal gear type, 19 cu in(310 cc) displacement per revolution, 3000 psi(20,685 kPa) maximum rated continouspressure

Motor, main brush -- internal gear type, 4.5 cu i(75 cc) displacement per revolution, 2400 psi(16,550 kPa) maximum rated continouspressure

Motor, side brush -- internal gear type, 2.8 cu in(45 cc) displacement per revolution, 1500 psi(10,340 kPa) maximum rated continouspressure

SPECIFICATIONS

365 MM173 (3---90)1-4

Motor, vacuum fan -- internal gear type, 0.194 cu in(3.2 cc) displacement per revolution, 2300 psi(15,860 kPa) maximum rated continouspressure

Cylinder, hopper lift -- double action type, 2.5 in(65 mm) bore x 12.62 in (320 mm) stroke,1.25 in (32 mm) diameter rod, 2500 psi (17,238kPa) maximum rated pressure

Cylinder, steering -- double action type, 2 in (50 mm)bore x 8 in (200 mm) stroke, 0.75 in(20 mm)diameter rod, 1500 psi (10,340 kPa) maximumrated pressure

BRAKING SYSTEM

Service brakes -- hydraulic drum brakes (2), one perfront wheel, master cylinder foot brake actuated.

Parking brakes -- utilizes service brakes, cableactuated

SUSPENSION SYSTEM

Front -- two 5.70 x 8 pneumatic tirestwo 6.00 x 9 solid tires with solid tire accessory

Rear -- one 6.90/6.00 x 9 pneumatic tireone 4.00 x 8 solid tire with solid tire accessory

SYSTEM FLUID CAPACITIES

Engine cooling system -- radiator 4 qt (3.8 L)total system -- 8.4 qt (8 L)total system with heater (accessory) --9.3 qt (8.8 L)

Engine lubricating oil -- 3.5 qt (3.3 L) with filter

Fuel tank -- 10 gal (38 L) gasoline 33 lb (15 kg) LPGHydraulic system -- reservoir 5.3 gal (20 L)

total system 6 gal (23 L)

GENERAL MACHINE DIMENSIONS/CAPACITIES

Length -- 97 in (2460 mm)

Width -- 58.3 in (1480 mm)

Height -- 55 in (1400 mm)Height with overhead guard/cab (accessory) -- 81.6

in (2075 mm)Height with overhead guard/cab and rotating/flashing

light (accessory) -- 88.8 in (2255 mm)

Track -- 54.5 in (1385 mm)

Wheelbase -- 54.5 in (1385 mm)

Main brush -- diameter, 14 in (355 mm)length, 48 in (1220 mm)

Side brush -- diameter, 21 in (535 mm)

Sweeping path width -- 48 in (1220 mm)Sweeping path width with side brush -- 60 in

(1525 mm)Hopper capacity -- 1200 lb (545 kg)

16 cu ft (0.45 m#)Dust filter area -- 110 sq ft (10.2 m@)

MACHINE WEIGHTS

GVWR -- 4300 lb (1950 kg)

GENERAL MACHINE PERFORMANCE

Maximum forward speed -- 8.5 mph (13.7 km/h)Maximum reverse speed -- 3 mph (4.8 km/h)Turning radius -- right, 104 in (2640 mm)

left, 77 in (1955 mm)U--turn, 118.5 in (3010 mm)

Maximum rated clemb/descent angle -- 15_ withempty hopper, 10_ with hopper full

SPECIFICATIONS

1-5365 MM173 (3---90)

MACHINE DIMENSIONS

TOP VIEW

SIDE VIEW

58.3 in(1480 mm)

97 in (2460 mm)

108 in(2745 mm)

81.6 in(2075 mm)

55 in(1400 mm)

02146

SPECIFICATIONS

365 MM173 (3---90)1-6

OPERATION

2-1365 MM173 (3--90)

SECTION 2CONTENTS

PagePREPARATION FOR OPERATION 2-3. . . . . . . . . .

AFTER UNLOADING AND BEFOREOPERATING THE MACHINE: 2-3. . . . . . . . .

OPERATION OF CONTROLS 2-4. . . . . . . . . . . . . .MACHINE COMPONENTS 2-4. . . . . . . . . . . . . .INSTRUMENT PANEL SYMBOLS 2-5. . . . . . . .CONTROLS AND INSTRUMENTS 2-6. . . . . . .BRAKE PEDAL 2-7. . . . . . . . . . . . . . . . . . . . . . . .DIRECTIONAL PEDAL 2-7. . . . . . . . . . . . . . . . . .PARKING BRAKE LEVER 2-7. . . . . . . . . . . . . . .OPERATOR SEAT 2-7. . . . . . . . . . . . . . . . . . . . .HAZARD LIGHT SWITCH 2-8. . . . . . . . . . . . . . .THROTTLE LEVER 2-8. . . . . . . . . . . . . . . . . . . .THROTTLE SWITCH 2-8. . . . . . . . . . . . . . . . . . .ENGINE CHOKE LEVER 2-8. . . . . . . . . . . . . . . .ENGINE CHOKE KNOB 2-8. . . . . . . . . . . . . . . . .CLOGGED FILTER INDICATOR 2-8. . . . . . . . .VACUUM FAN AND FILTER SHAKER

SWITCH 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . .II SPEEDt SWITCH 2-8. . . . . . . . . . . . . . . . . . .HOPPER DOOR SWITCH 2-8. . . . . . . . . . . . . . .HOPPER SWITCH 2-9. . . . . . . . . . . . . . . . . . . . .SIDE BRUSH POSITION LEVER 2-9. . . . . . . . .MAIN BRUSH POSITION LEVER 2-9. . . . . . . .MAIN BRUSH HEIGHT ADJUSTMENT

KNOB 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .STEERING TILT LEVER 2-9. . . . . . . . . . . . . . . .ENGINE HOUR METER 2-10. . . . . . . . . . . . . . . .ENGINE OIL PRESSURE GAUGE 2-10. . . . . . .ENGINE COOLANT TEMPERATURE

GAUGE 2-10. . . . . . . . . . . . . . . . . . . . . . . . . . . .STEERING WHEEL 2-10. . . . . . . . . . . . . . . . . . . .FUEL LEVEL GAUGE 2-10. . . . . . . . . . . . . . . . . .VOLTAGE GAUGE 2-10. . . . . . . . . . . . . . . . . . . . .OPERATING LIGHTS SWITCH 2-10. . . . . . . . . .IGNITION SWITCH 2-10. . . . . . . . . . . . . . . . . . . . .HOPPER SUPPORT BAR 2-11. . . . . . . . . . . . . . .

TO ENGAGE HOPPER SUPPORT BAR 2-11TO DISENGAGE HOPPER

SUPPORT BAR 2-11. . . . . . . . . . . . . . . . . .CIRCUIT BREAKERS 2-12. . . . . . . . . . . . . . . . . . .

PageMACHINE OPERATION 2-13. . . . . . . . . . . . . . . . . . . .

NORMAL SWEEPING OPERATION 2-13. . . . . .PRE-START CHECKLIST 2-13. . . . . . . . . . . .TO START MACHINE 2-13. . . . . . . . . . . . . . . .TO SWEEP 2-14. . . . . . . . . . . . . . . . . . . . . . . . .TO DUMP HOPPER 2-14. . . . . . . . . . . . . . . . .POST OPERATION CHECKLIST --

ENGINE OPERATING 2-15. . . . . . . . . . . . .TO STOP MACHINE 2-15. . . . . . . . . . . . . . . . .POST OPERATION CHECKLIST --

ENGINE STOPPED 2-15. . . . . . . . . . . . . . .OPERATION ON GRADES 2-15. . . . . . . . . . . . . .MACHINE TROUBLESHOOTING 2-16. . . . . . . .

ACCESSORIES OPERATION 2-17. . . . . . . . . . . . . .VACUUM WAND ACCESSORY 2-17. . . . . . . . . .

TO OPERATE VACUUM WAND 2-17. . . . . . .CAB PRESSURIZER 2-18. . . . . . . . . . . . . . . . . . .

TRANSPORTING MACHINE 2-19. . . . . . . . . . . . . . .PUSHING OR TOWING MACHINE 2-19. . . . . . .MACHINE JACKING 2-19. . . . . . . . . . . . . . . . . . . .

TO JACK UP MACHINE 2-19. . . . . . . . . . . . . .MACHINE TIE-DOWNS 2-20. . . . . . . . . . . . . . . . .

MACHINE STORAGE 2-21. . . . . . . . . . . . . . . . . . . . .STORING MACHINE 2-21. . . . . . . . . . . . . . . . . . .

OPERATION

365 MM173 (3--90)2-2

OPERATION

2-3365 MM173 (3--90)

PREPARATION FOR OPERATION

AFTER UNLOADING AND BEFORE OPERATINGTHE MACHINE:

1. Check the machine for shipping damage.

2. Read this manual carefully before operating orservicing the machine.

FOR SAFETY: Do not operate the machine unlessoperation manual is read and understood.

3. Check the hydraulic fluid level in the hydraulicfluid reservoir, using the dipstick provided.TENNANT hydraulic fluid is recommended. IfTENNANT hydraulic fluid is not available, useonly new, approved hydraulic fluid. SeeHYDRAULICS in the MAINTENANCE section.

4. Check the engine oil level.

5. Check the radiator coolant level.

6. Check the brush adjustment, as described inBRUSHES in the MAINTENANCE section.

7. Check the air pressure of the tires. Pressureshould be as listed in BRAKES AND TIRES inthe MAINTENANCE Section.

8. Fill the fuel tank, or install an LPG fuel tank onthe machine per the instructions in this manual.

WARNING: Machine can have staticelectricity charge. When pouring fuel, spark

can ignite fuel causing fire or explosion. Connectwire attached to fuel can to machine to dischargespark before pouring fuel.

OPERATION

365 MM173 (3--90)2-4

OPERATION OF CONTROLS

A

BC

D E

F

G

H

I

JK

05958

MACHINE COMPONENTS

A. Parking Brake G. Vacuum Wand Connection DoorB. Overhead Guard H. Hopper DoorC. Operator Seat I. Side BrushD. Steering Console J. Hopper Support BarE. Engine Cover K. Main Brush Access DoorF. Hopper Cover

OPERATION

2-5365 MM173 (3--90)

INSTRUMENT PANEL SYMBOLS

These symbols are used to identify controls anddisplays on the machine:

Side Brush Down and On

Side Brush Up

Main Brush Free-Float

Main Brush Down

Main Brush Up

Hopper Door Close

Hopper Door Open

Hopper Down

Hopper Up

Main Brush 1

Main Brush 2

Vacuum Fan

Filter Shaker

Filter Clogged

Choke

Fast

Idle

Engine Start

Hazard Light

Operational Lights

OPERATION

365 MM173 (3--90)2-6

For machines belowserial number 005774

For machines serialnumber 005775 to

006999

A

B

C

D

E

FG

H

I

J

K

L

M

N

OP

Q R S

T

U

V

W X

Y Z

AA

BB

FBB

03762

CONTROLS AND INSTRUMENTS

A. Brake Pedal O. Main Brush Height Adjustment KnobB. Directional Control Pedal P. Steering Tilt LeverC. Parking Brake Lever Q. Engine Hour MeterD. Operator Seat R. Engine Oil Pressure GaugeE. Hazard Lamp Switch S. Engine Coolant Temperature GaugeF. Throttle Lever T. Steering WheelG. Engine Choke Lever U. Horn ButtonH. Clogged Filter Indicator V. Fuel Level GaugeI. Vacuum Fan and Filter W. Voltage Gauge

Shaker Switch X. Operating Lights SwitchJ. II Speedt Switch Y. Ignition SwitchK. Hopper Door Switch Z. Hopper Support BarL. Hopper Switch AA.Throttle SwitchM. Side Brush Position Lever BB.Engine Choke KnobN. Main Brush Position Lever

OPERATION

2-7365 MM173 (3--90)

BRAKE PEDAL

The brake pedal operates the hydraulic drum brakeson the two front wheels.

To stop the machine, return the directional pedal toneutral; then apply pressure to the brake pedal.

DIRECTIONAL PEDAL

The directional pedal controls the propelling drive.The foot pedal is used to select the direction of traveland the propelling speed of the machine.

AB

C

D

E

00116

DIRECTIONAL CONTROL PEDAL

A. “Reverse” PositionB. “Neutral” PositionC. “Forward” PositionD. Toe PortionE. Heel Portion

To travel forward, press the “toe” portion of the pedal;press the “heel” portion of the pedal for reverse travel.The propelling speed of the machine is regulated byvarying the pressure on the pedal.

If the machine creeps when the pedal is in the“neutral” position, adjust the pedal as directed inDIRECTIONAL PEDAL in the MAINTENANCEsection.

PARKING BRAKE LEVER

The parking brake lever controls the brakes on thefront wheels. To set the parking brake, pull the brakehandle up. To release the parking brake, push thebrake handle down. Always set the parking brakebefore leaving the machine unattended and beforeworking on the machine.

FOR SAFETY: Before leaving or servicingmachine; stop on level surface, set parking brake,and turn off the machine and remove key.

OPERATOR SEAT

The operator seat is a three-way adjustable seat witharmrests. It has adjustments to compensate foroperator weight, to vary the backrest angle, and tovary the front-to-rear seat position.

The weight adjustment lever has three positions. Oneposition is for light-weight operators, one formiddle-weight operators, and one for heavy-weightoperators. Pull the lever up for light-weight operators,position the lever horizontally for middle-weightoperators, and down for heavy-weight operators.

The backrest angle is adjusted by rotating the knobclockwise to decrease the backrest angle orcounterclockwise to increase the backrest angle.

The seat position is adjusted by pulling the seatposition lever, located on the lower front edge of theseat. Pull the lever out to the left, sliding the seatforward or backward to a comfortable position, andreleasing the lever.

The right side armrest may be rotated up and back toenter or exit from the operator seat.

A

B

C

D

01435

OPERATOR SEAT

A. SeatB. Weight Adjustment LeverC. Backrest Angle KnobD. Armrest

OPERATION

365 MM173 (3--90)2-8

The operator seat also tilts forward to allow access tothe gasoline fuel tank and hydraulic reservoir fill caps.A support rod has also been provided to hold the seatin the forward tilted position.

A

B

03763

SEAT SUPPORT ROD

A. Support RodB. Seat Base

HAZARD LIGHT SWITCH

The hazard light switch is present on machineswith the rotating or flashing light accessory. Tooperate the light, place the switch in the top position.To turn the light off, place the switch in the bottomposition.

THROTTLE LEVER

The throttle lever controls the engine governed speedon machines below serial number 007000. Push thelever forward to slow the engine to idle speed. Pull thelever back to speed the engine to the maximumgoverned speed.

THROTTLE SWITCH

The throttle switch controls the engine governedspeed on machines serial number 007000 and above.To start the engine, place the switch in the bottom

(Engine Start) position. To slow the engine beforestopping it, place the switch in the middle (Idle)position. To speed up the engine to operating speed,place the switch in the top (Fast) position.

ENGINE CHOKE LEVER

The engine choke lever is present on gasolinepowered machines below serial number 005774. Thelever controls the engine choke. To close the chokefor cold starting, push the engine choke lever forwardinto the “FULL” position. After the engine starts andwarms up, open the choke by pulling the choke leverback into the “RUN” position. It is not necessary tochoke a warm engine.

ENGINE CHOKE KNOB

The engine choke knob is present on gasolinemachines serial number 005774 and above. The knobcontrols the engine choke. To close the choke for coldstarting, pull the choke knob out. To open the choke,push the knob in.

CLOGGED FILTER INDICATOR

The clogged filter indicator lights when the dustfilter is clogged. Shake or clean the hopper dust filterwhenever the indicator lights.

VACUUM FAN AND FILTER SHAKER SWITCH

The vacuum fan and filter shaker switch controls thevacuum fan and the hopper dust filter shaker.

To start the vacuum fan, place the switch in the top(Vacuum Fan) position. To stop the vacuum fan,

place the switch in the middle position. To shake thehopper dust filters, press the bottom (FilterShaker) of the switch.

II SPEEDt SWITCH

The II Speedt switch controls the speed of thevacuum fan and the main brush. Place the switch inthe bottom (Main Brush 1) position for sweepingup normal debris. Place the switch in the top(Main Brush 2) position for sweeping up light litter.

HOPPER DOOR SWITCH

The hopper door switch controls the hopper doorposition. To open the hopper door, press the bottom

(Hopper Door Open) of the switch. To close thehopper door, press the top (Hopper Door Close)of the switch.

OPERATION

2-9365 MM173 (3--90)

HOPPER SWITCH

The hopper switch controls the hopper position. Toraise and dump the hopper, press and hold thebottom (Hopper Up) of the switch. This will raisethe hopper into the dump position. Press the switchuntil enough hopper-to-dumpster clearance is reachedand release the switch. Continuing to press the switchwill raise the hopper to the maximum dump height.



To lower the hopper, place the switch in the top(Hopper Down) position. This will lower and return thehopper to the operating position.

SIDE BRUSH POSITION LEVER

The side brush position lever controls brush positionand rotation of the side brush.

To lower and start the side brush, pull the side brushposition lever back and to the left; then release thelever into the (Side Brush Down and On)position.

To raise and stop the side brush, pull the side brushposition lever back to the right and release the leverinto the (Side Brush Up) position.

NOTE: The side brush will not rotate unless the mainbrush position lever is in the (Main Brush Down) or(Main Brush Free-Float) positions.

MAIN BRUSH POSITION LEVER

The main brush position lever controls the positionand rotation of the main brush.

To lower and start the main brush, pull the main brushposition lever back and to the left. Then release thelever into the (Main Brush Down) position --allowing the lever to move forward and to the right willplace the lever in the (Main Brush Free-Float)position.

To raise and stop the main brush, pull the main brushposition lever back to the right and release the leverinto the (Main Brush Up) position.

NOTE: Always place the main brush position lever inthe (Main Brush Up) position when the machine is notbeing used for a period of time. This will prevent themain brush from getting a flat spot.

MAIN BRUSH HEIGHT ADJUSTMENT KNOB

The main brush height adjustment knob is locatedbehind an access door next to the operator’s left foot.The adjustment knob controls the amount of mainbrush contact with the floor.

To decrease the main brush floor contact, loosen thelocking knob and thread the adjustment knobclockwise. To increase the main brush floor contact,loosen the locking knob and thread the adjustmentknob counterclockwise. Retighten the locking knobafter making any adjustment.

A

B

C

02150


A. Access DoorB. Adjustment KnobC. Locking Knob

STEERING TILT LEVER

The steering tilt lever controls the tilt angle of thesteering console.

To adjust the angle of the steering console, push thelever forward, adjust the console to a comfortableangle, and release the lever.

OPERATION

365 MM173 (3--90)2-10

ENGINE HOUR METER

The hour meter records the number of hours themachine has been operated. This information isuseful in determining when to service the machine.

ENGINE OIL PRESSURE GAUGE

The engine oil pressure gauge registers the engine oilpressure. Normal engine oil pressure ranges from 20to 35 psi (140 to 240 kPa) at full engine throttle. If thegauge registers an oil pressure reading below 7 psi(50 kPa), stop the engine immediately and determinethe cause. Failure to stop the engine will result inengine damage.

ENGINE COOLANT TEMPERATURE GAUGE

The engine coolant temperature gauge registers theengine coolant temperature. Normal engine coolanttemperatures range up to 200_ F (93 _C).Temperatures above this level indicate anover-heating engine. This condition may be due to alow coolant level, a clogged radiator, a loose fan belt,a defective thermostat, or other engine malfunctions.Engine overheating will always cause a coolant loss.If coolant loss does not occur, check for malfunctionof the temperature sending unit.

STEERING WHEEL

The automotive-type steering wheel controls asteering cylinder connected to the rear wheel support.It is recommended that the steering wheel not beturned excessively when the engine is not operating.A horn button is located in the center of the steeringwheel.

FUEL LEVEL GAUGE

The fuel level gauge is present on all gasolinepowered machines. It indicates how much fuel is leftin the fuel tank.

VOLTAGE GAUGE

The voltage gauge indicates the present voltagepotential of the battery. Normal battery voltage is 10to 14 volts. If the battery voltage exceeds 14 volts, itmay be overcharging. If the battery voltage falls below10 volts, it may not be accepting or getting a chargefrom the alternator. Overcharging and underchargingare indications that one or more electricalcomponents are in need of repair.

OPERATING LIGHTS SWITCH

The operating lights switch controls theheadlights, taillights, and side brush spot light. Tooperate the lights, place the switch in the bottomposition. To turn off the lights, place the switch in thetop position.

IGNITION SWITCH

The key operated ignition switch starts the engine. Tostart the engine, turn the key clockwise. To turn theignition off, turn the key counterclockwise.

NOTE: Do not operate the starter motor for more than10 seconds at a time or after the engine has started.Allow the starter to cool between starting attempts.The starter motor may be damaged if it is operatedincorrectly.

FOR SAFETY: Before starting machine, make sureall safety devices are in place and operateproperly.

OPERATION

2-11365 MM173 (3--90)

HOPPER SUPPORT BAR

The hopper support bar is present on the operator’sside of the hopper. The support bar holds the hopperin a raised position to allow work to be done under thehopper. Do not rely on the machine hydraulic systemto keep the hopper raised.


TO ENGAGE HOPPER SUPPORT BAR

1. Set the machine parking brake and start theengine.

FOR SAFETY: Before leaving or servicing themachine; stop on level surface, set parking brake.

2. Place the engine throttle control in the (Fast)position.

3. Raise the hopper to the fully raised position.

4. Lift and position the hopper support bar in thefront bumper slot.

A

B

02151

ENGAGED HOPPER SUPPORT BAR

A. Front Bumper SlotB. Support Bar

5. Slowly lower the hopper so the front bumperrests securely on the support bar.

6. Turn the engine off.

7. Check the support bar to make sure it issecurely engaged.

TO DISENGAGE HOPPER SUPPORT BAR

1. Start the engine.

2. Place the engine throttle control in the (Fast)position.

3. Raise the hopper to the fully raised position.

4. Lower the support bar into its storage position.

A

02142

DISENGAGED HOPPER SUPPORT BAR

A. Support Bar

5. Lower the hopper.

6. Turn the engine off.

OPERATION

365 MM173 (3--90)2-12

CIRCUIT BREAKERS

Circuit breakers are resetable circuit protectiondevices designed to stop the flow of current in theevent of a circuit overload. Once tripped, circuitbreakers must cool before they automatically reset. Ifthe overload which caused the circuit breaker to trip isstill present in the circuit, the circuit breaker willcontinue to stop current flow until the overload iscorrected.

The circuit breakers are located below the steeringconsole.

The chart below shows the various circuit breakersand the electrical components they protect.

PROTECTIVEDEVICE RATING CIRCUIT PROTECTED

CB--1 15 A Filter shakerCB--2 15 A Horn, hopper doorCB--3 15 A Engine ignition, gaugesCB--4 15 A LightsCB--5 15 A Brush drive, hopper lift,

vacuum fanCB--6 15 A Cab heater, blower,

wipers

OPERATION

2-13365 MM173 (3--90)

MACHINE OPERATION

NORMAL SWEEPING OPERATION

A normal sweeping operation consists of seventypical operations: pre-start checklist, startingmachine, sweeping, dumping hopper, post operationchecklist -- engine operating, stopping machine, andpost operation checklist -- engine stopped.

The PRE-START CHECKLIST lists things to checkbefore starting the machine.

TO START MACHINE lists the steps required to startthe machine.

TO SWEEP lists things to keep in mind before andduring the sweeping operation.

TO DUMP HOPPER lists the steps required to dumpthe hopper.

POST OPERATION CHECKLIST -- ENGINEOPERATING lists things to check before stopping themachine engine.

TO STOP MACHINE lists the steps required to stopthe machine.

POST OPERATION CHECKLIST -- ENGINESTOPPED lists things to check after stopping themachine engine.

PRE-START CHECKLIST

Check under the machine for leak spots.

Check the engine lubricating oil level.

Check the engine air filter service indicator.

Check the fuel level.

Check for LPG odor, or frost on LPG hoses andcomponents, indicating a leak.

Check the brakes and controls for proper operation.

Check the service records to determine servicerequirements.

TO START MACHINE

NOTE: Before starting the machine, perform thepre-start checks.

1. LPG machines: Slowly open the liquid servicevalve.

NOTE: Opening the service valve too quickly maycause the service valve check valve to stop the flowof LPG fuel. If the check valve stops the flow of fuel,close the service valve, wait a few seconds, andslowly open the service valve once again.

2. The machine operator must be in the operator’sseat with the directional control pedal in the“neutral” position and a foot on the brake pedalor the parking brake set.

FOR SAFETY: Before starting machine, make sureall safety devices are in place and operateproperly.

3. Cold gasoline engines: Move the choke leverforward into the “FULL” position, or pull out thechoke knob about three-fourths of the way. Pullthe choke lever back, or push the choke knob in,after the engine has started and is runningsmoothly.

4. Place the throttle control in the (Idle) position.

5. Turn the ignition switch key clockwise until theengine starts.

NOTE: Do not operate the starter motor for more than10 seconds at a time or after the engine has started.Allow the starter to cool between starting attempts.The starter motor may be damaged if it is operatedincorrectly.

6. Allow the engine and hydraulic system to warmup three to five minutes.

7. Release the machine parking brake.

8. Place the throttle control in the (Fast) position,and drive the machine to the area to be swept.

OPERATION

365 MM173 (3--90)2-14

TO SWEEP

Plan the sweeping in advance. Try to arrange longruns with minimum stopping and starting. Sweepdebris from very narrow aisles into main aisles aheadof time. Do an entire floor or section at one time.

Pick up oversize debris before sweeping. Flatten orremove bulky cartons from aisles before sweeping.Pick up pieces of wire, twine, string, etc., which couldbecome entangled in brush or brush plugs. Overlapbrush paths.

Avoid turning the steering wheel too sharply when themachine is in motion. The machine is very responsiveto the movement of the steering wheel. Avoid suddenturns, except in emergencies.

Sweep as straight a path as possible. Avoid bumpinginto posts or scraping the sides of the sweeper.

Speed the main brush from (Main Brush 1) to (MainBrush 2) when light letter is to be swept up. Do notoveruse the (Main Brush 2) speed in dustyenvironments because the machine dusting may clogthe hopper dust filters. The (Main Brush 1) speed isbest for sweeping up normal debris.

Stop the machine vacuum when sweeping in wetconditions to avoid soaking the hopper dust filter.

1. Place the vacuum fan and filter shaker switch inthe top (Vacuum Fan) position.

2. Place the II Speedt switch in the top (MainBrush 2) or the bottom (Main Brush 1) positiondepending on the debris to be picked up.

3. Move the main brush position lever to the (MainBrush Down) or (Main Brush Free-Free)position.

4. Move the side brush position lever to the (SideBrush Down and On) position.

5. Sweep as required.

TO DUMP HOPPER

1. Pull the side brush position lever back into the(Side Brush Up) position.

2. Pull the main brush position lever back into the(Main Brush Up) position.

3. Press the bottom (Filter Shaker) of the vacuumfan and filter shaker switch to shake the hopperdust filter. Place the switch in the middle positionafter the filter shaker stops.

4. Slowly drive the machine up to the dump site ordumpster.

5. Press the top (Hopper Door Close) of thehopper door switch to close the hopper door.Press the bottom (Hopper Up) of the hopperswitch to raise and rotate the hopper into thedump position. Hold the switch down until thedesired hopper height is reached.



6. Press the bottom (Hopper Door Open) of thehopper door switch to open the hopper door andempty the hopper.

NOTE: Lowering the hopper into the dumpster mayhelp to control flying dust.

7. Press the bottom (Hopper Up) of the hopperswitch to allow the hopper to raise and clear thedumpster.

8. Press the top (Hopper Door Close) or thehopper door switch to close the hopper door.

9. Slowly back the machine away from the dumpsite or dumpster.

10. Place the hopper switch in the top (HopperDown) position to lower and rotate the hopperinto the operating position.

11. Press the bottom (Hopper Door Open) of thehopper door switch to open the hopper door.

OPERATION

2-15365 MM173 (3--90)


13. Place the II Speedt switch in the bottom(Main Brush 1) or the top (Main Brush 2)position depending on the debris to be pickedup.

14. Move the main brush position lever to the (MainBrush Down) or (Main Brush Free-Free)position.

15. Move the side brush position lever to the (SideBrush Down and On) position.

16. Continue sweeping as required.

POST OPERATION CHECKLIST -- ENGINEOPERATING

Check brush pattern for width and evenness.

TO STOP MACHINE

NOTE: Before leaving the machine, perform the postoperation checks.

1. Return the directional control pedal to the“neutral” position. Apply the brake.

2. Pull the side brush position lever back into the(Side Brush Up) position.

3. Pull the main brush position lever back into the(Main Brush Up) position.

4. Place the vacuum fan and filter shaker switch inthe middle position.

5. Turn the operating lights off if used.


7. Set the machine parking brake.

8. Turn the ignition key switch counterclockwise.Remove the key from the ignition switch.

FOR SAFETY: Before leaving or servicingmachine; stop on level surface, set parking brake,and turn off machine and remove key.

9. Close the LPG tank liquid service valve.

POST OPERATION CHECKLIST -- ENGINESTOPPED

Check the skirts for damage, wear, and adjustment.

Check for wire or string tangled on the brushes.

Check for LPG odor, or frost on the LPG hoses andcomponents, indicating a leak.

Check for leaks.

OPERATION ON GRADES

Drive the machine slowly on grades. Use the servicebrakes to control machine speed.

FOR SAFETY: When using machine, go slow ongrades and slippery surfaces.

The maximum rated ramp climb and descent angle is15_ with an empty hopper, and 10_ with a fullhopper.

OPERATION

365 MM173 (3--90)2-16

MACHINE TROUBLESHOOTING

Problem Cause Remedy

Excessive dusting. Dust skirts and seals worn, Replace or adjust skirts ordamaged, not adjusted properly. seals.

Thermo-Sentryt tripped. Reset Thermo-Sentryt.

Dust filter clogged. Shake and/or clean or replacefilter.

Poor sweeping performance. Brushes worn. Replace brushes.

Wrong brush for application. Replace brush.

Brushes not adjusted properly. Adjust brushes.

Main brush drive failure. See HYDRAULIC SYSTEMTROUBLESHOOTING in theMAINTENANCE section: Mainbrush does not turn.

Side brush drive failure. See HYDRAULIC SYSTEMTROUBLESHOOTING in theMAINTENANCE section: Sidebrush does not turn.

Hopper full. Empty hopper.

OPERATION

2-17365 MM173 (3--90)

ACCESSORIES OPERATION

VACUUM WAND ACCESSORY

The vacuum wand accessory gives the machine theadded flexibility of picking up debris not accessible tothe machine. A 120 in (3050 mm) long hose utilizesthe machine vacuum system.

TO OPERATE VACUUM WAND

1. Stop the machine close to the area to becleaned.

2. Place the main brush position lever in the (MainBrush Up) and side brush position lever in the(Side Brush Up) position.

3. Stop the engine and set the machine parkingbrake.

FOR SAFETY: Before leaving or servicingmachine; stop on level surface, set parking brake,and turn off machine.

4. Remove the vacuum wand and wand hose fromtheir storage clips.

5. Open the hopper cover.

6. Pull the wand door handles up and lower theminto the hopper to close the wand door.

B

A

03775

CLOSING WAND DOOR

A. Vacuum Wand ConnectionB. Wand Door Handles

7. Close the hopper cover.

8. Push one end of the wand hose onto the wandconnection.

9. Push the other end of the wand hose onto thevacuum wand.


WARNING: Engine emits toxic gases.Severe respiratory damage or asphyxiation

can result. Provide adequate ventilation. Consultwith your regulatory agency for exposure limits.Keep engine properly tuned.

11. Place the throttle control in the (Fast) position.

12. Place the II Speedt switch in the top (MainBrush 2) position.


14. Vacuum the area as required.

15. When finished, place the vacuum fan and filtershaker switch in the middle position.


16. Stop the engine.

17. Pull the vacuum hose out of the vacuum hoseconnection.

18. Disconnect the wand hose from the vacuumwand.

19. Pull the wand door handles up and sideways toopen the wand door.

NOTE: The wand door must be reopened to allow thehopper vacuum system to operate.


21. Return the vacuum wand and wand hose to theirstorage clips.

OPERATION

365 MM173 (3--90)2-18

CAB PRESSURIZER

The cab pressurizer is included in the cab accessory.The pressurizer includes a dome light,defroster/circulation fan and vent controls, windshieldwiper control, and heater control for machinesequipped with the cab heater accessory.

A

B

C

DE

03779

CAB PRESSURIZER

A. Defroster/Circulation Fan SwitchB. Vent ControlsC. Windshield Wiper SwitchD. Heater SwitchE. Dome Light Switch

OPERATION

2-19365 MM173 (3--90)

TRANSPORTING MACHINE

PUSHING OR TOWING MACHINE

The machine may be pushed from the front or therear, using the bumpers provided, only after placingthe rear wheel on a dolly.

The machine may be towed in either direction afterplacing the rear wheel on a dolly. Do not pull on thefront bumper -- pull on the hopper pivot tube.

ATTENTION! Do not push or tow the machinewithout placing the rear wheel on a dolly; themachine hydraulic system may be damaged.

A03765

FRONT TOW LOCATION

A. Hopper Pivot Tube

MACHINE JACKING

The machine may be jacked up for service at thedesignated locations. Use a jack of adequate capacityand good working condition. Always stop the machineon a flat, level surface and block the tires beforejacking the machine up. The front jacking locationsare on the flat bottom edge of the machine frame infront of the front tires.

The rear jacking location is the middle flat bottomedge of the rear bumper.

TO JACK UP MACHINE

1. Empty the debris hopper.



3. Block the tires, which are not being jacked up, inorder to secure the machine position.


up.

4. Use a jack of adequate capacity to raise themachine. Jack up the machine only at thedesignated locations.



A02141

FRONT JACKING LOCATION

A. Jacking Location

A

03764

REAR JACKING LOCATION

A. Jacking Location

OPERATION

365 MM173 (3--90)2-20

5. Block machine up with jack stands or similardevices near the designated jacking locations tosecure the machine.



6. Lower the machine onto the jack stands.

7. Check to make sure the machine is secure.

8. Service the machine as required.

9. When finished servicing the machine, raise themachine off the jack stands.

10. Remove the jack stands from under themachine.

11. Lower the machine.

12. Remove the blocks from the tires.

MACHINE TIE-DOWNS

The machine may be tied down at each of the fourcorners of the machine at the locations specified.

To tie the machine down, use the hopper pivot tube orfront wheel pocket holes in the front and the holes inthe lower rear machine frame in the back.

A

B

03765

FRONT TIE-DOWN LOCATION

A. Hopper Pivot TubeB. Pocket Hole

A03764

REAR TIE-DOWN LOCATION

A. Tie-Down Hole

When transporting the machine on a trailer or in atruck, be sure to set the machine parking brake andblock the machine tires to prevent the machine fromrolling.

OPERATION

2-21365 MM173 (3--90)

MACHINE STORAGE

STORING MACHINE

When storing the machine for extended periods oftime, the following procedures must be followed tolessen the chance of rust, sludge, and otherundesirable deposits from forming.


2. Change the engine oil.

3. Place the main brush position lever in the (MainBrush Up) position and side brush position leverin the (Side Brush Up) position.

4. Park the machine in a cool and dry area.

5. Stop the engine.

6. Fill the hydraulic reservoir with hydraulic fluid tothe full mark on the dipstick to preventexcessive condensation from forming in thereservoir.

7A. To store the machine 30 to 90 days:

1. Remove the spark plugs.

2. Pour 3 oz (90 cc) of clean engine oil intoeach of the spark plug holes.

3. Remove the ignition coil high tension wire.Operate the engine starter motor for tenseconds. This distributes the oil over thecylinder walls.

NOTE: Before preparing the engine for storage, allowit to cool down to the surrounding temperature. Oiladheres to cold metal surfaces much better than hotsurfaces.

4. Replace the high tension coil wire andspark plugs.

5. Drain the gasoline from the carburetor.

7B. To store the machine more than 90 days:

1. Remove the spark plugs.

2. Pour 3 oz (90 cc) of clean engine oil intoeach of the spark plug holes.

3. Remove the ignition coil high tension wire.Operate the engine starter motor for tenseconds. This distributes the oil over thecylinder walls.

NOTE: Before preparing the engine for storage, allowit to cool down to the surrounding temperature. Oiladheres to cold metal surfaces much better than hotsurfaces.

4. Replace the high tension coil wire andspark plugs.

5. Drain the engine oil from the oil pan.

6. Drain the coolant from the radiator andengine block.

7. Close the engine cooling system draincocks.

8. Drain gasoline from the carburetor, fueltank, and the fuel lines.

9. Seal the air cleaner inlet and the exhaustoutlet with weatherproof masking tape.

10. Tighten the engine oil filler cap, the fueltank cap, and the radiator cap to makecertain they are securely in place.

OPERATION

365 MM173 (3--90)2-22

MAINTENANCE

3-1365 MM173 (3--90)

SECTION 3CONTENTS

PageRECOMMENDED FIRST 50-HOUR

MACHINE INSPECTION 3-3. . . . . . . . . . . . . . . .MAINTENANCE CHART 3-4. . . . . . . . . . . . . . . . . . .LUBRICATION 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .HOPPER PIVOT 3-6. . . . . . . . . . . . . . . . . . . . . . .SIDE BRUSH PIVOT 3-6. . . . . . . . . . . . . . . . . . .REAR WHEEL SUPPORT 3-7. . . . . . . . . . . . . . .STEERING CYLINDER ENDS 3-7. . . . . . . . . . .FRONT WHEEL BEARINGS 3-7. . . . . . . . . . . . .

HYDRAULICS 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . .HYDRAULIC FLUID 3-8. . . . . . . . . . . . . . . . . . . .HYDRAULIC FLUID RESERVOIR 3-8. . . . . . . .

TO DRAIN HYDRAULIC FLUIDRESERVOIR 3-9. . . . . . . . . . . . . . . . . . . . .

TO FILL HYDRAULIC FLUIDRESERVOIR 3-9. . . . . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID RESERVOIRBREATHER 3-10. . . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID FILTER 3-10. . . . . . . . . . . . .TO REPLACE HYDRAULIC

FLUID FILTER ELEMENT 3-10. . . . . . . . .DIRECTIONAL PEDAL 3-11. . . . . . . . . . . . . . . . . .

TO ADJUST DIRECTIONALPEDAL LINKAGE 3-11. . . . . . . . . . . . . . . . .

HYDRAULIC FLUID LEAKS 3-13. . . . . . . . . . . . .HYDRAULIC SCHEMATIC 3-14. . . . . . . . . . . . . .HYDRAULIC SYSTEM

TROUBLESHOOTING 3-15. . . . . . . . . . . . . . .ENGINE 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE LUBRICATION 3-17. . . . . . . . . . . . . . . . .COOLING SYSTEM 3-17. . . . . . . . . . . . . . . . . . . .AIR INTAKE SYSTEM 3-18. . . . . . . . . . . . . . . . . .

AIR FILTER SERVICE INDICATOR 3-18. . . .AIR FILTER 3-18. . . . . . . . . . . . . . . . . . . . . . . . .TO REPLACE AIR FILTER ELEMENT 3-19.

FUEL SYSTEM -- GASOLINE 3-21. . . . . . . . . . . .FUEL FILTER 3-21. . . . . . . . . . . . . . . . . . . . . . .CARBURETOR 3-21. . . . . . . . . . . . . . . . . . . . .

FUEL SYSTEM -- LPG 3-21. . . . . . . . . . . . . . . . . .LPG FUEL SYSTEM 3-21. . . . . . . . . . . . . . . . .FUEL TANKS 3-22. . . . . . . . . . . . . . . . . . . . . . .TO CHANGE AN LPG FUEL TANK 3-23. . . .FUEL FILTER LOCK 3-23. . . . . . . . . . . . . . . . .VAPORIZER-REGULATOR 3-23. . . . . . . . . . .CARBURETOR 3-24. . . . . . . . . . . . . . . . . . . . .OIL PRESSURE SWITCH 3-24. . . . . . . . . . . .

LPG FUEL TROUBLESHOOTING 3-24. . . . . . . .

PageGOVERNOR (For machines below serial

number 007000) 3-25. . . . . . . . . . . . . . . . . . . . .TO ADJUST GOVERNOR (For machines

below serial number 007000) 3-25. . . . . . .GOVERNOR (For machines serial number

007000 and above) 3-25. . . . . . . . . . . . . . . . . .ELECTRICAL SYSTEM 3-26. . . . . . . . . . . . . . . . .

SPARK PLUGS 3-26. . . . . . . . . . . . . . . . . . . . .DISTRIBUTOR (For machines below

serial number 007000) 3-26. . . . . . . . . . . . .TO REPLACE IGNITION POINTS (For

machines below serialnumber 007000) 3-27. . . . . . . . . . . . . . . . . .

DISTRIBUTOR IGNITION TIMING (Formachines below serialnumber 007000) 3-28. . . . . . . . . . . . . . . . . .

TO CHECK AND ADJUST DISTRIBUTORIGNITION TIMING (For machines

below serial number 007000) 3-28. . . . . . .ENGINE IGNITION TIMING (For

machines serial number 007000and above) 3-29. . . . . . . . . . . . . . . . . . . . . . .

CYLINDER HEAD 3-29. . . . . . . . . . . . . . . . . . . . . .CYLINDER HEAD 3-29. . . . . . . . . . . . . . . . . . .VALVE TAPPET CLEARANCE 3-30. . . . . . . .

CRANKCASE VENTILATION SYSTEM 3-30. . .TUNE-UP CHART 3-30. . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL SYSTEM 3-31. . . . . . . . . . . . . . . . . . . .BATTERY 3-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . .ELECTRICAL SCHEMATIC (For machines

below serial number 007000) 3-32. . . . . . . . . .ELECTRICAL SCHEMATIC (For machines

serial number 007000 and above) 3-34. . . . . .BELTS AND CHAINS 3-36. . . . . . . . . . . . . . . . . . . . . .

ALTERNATOR BELT (For machines belowserial number 007000) 3-36. . . . . . . . . . . . . . .

ENGINE FAN BELT (For machines belowserial number 007000) 3-36. . . . . . . . . . . . . . .

ENGINE FAN BELT (For machines serialnumber 007000 and above) 3-36. . . . . . . . . . .

STATIC DRAG CHAIN 3-36. . . . . . . . . . . . . . . . . .

MAINTENANCE

365 MM173 (NIL)3-2

PageDEBRIS HOPPER 3-37. . . . . . . . . . . . . . . . . . . . . . . . .

HOPPER DUST FILTER 3-37. . . . . . . . . . . . . . . .TO REMOVE HOPPER DUST FILTER 3-37.TO INSTALL HOPPER DUST FILTER 3-38. .

THERMO-SENTRYt 3-38. . . . . . . . . . . . . . . . . . .VACUUM FAN AND MAIN BRUSH

SHUT-OFF SWITCH 3-39. . . . . . . . . . . . . . . . .DEBRIS HOPPER 3-39. . . . . . . . . . . . . . . . . . . . . .

TO ADJUST HOPPER 3-39. . . . . . . . . . . . . . .BRUSHES 3-44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAIN BRUSH 3-44. . . . . . . . . . . . . . . . . . . . . . . . . .TO REPLACE MAIN BRUSH 3-44. . . . . . . . . .TO CHECK AND ADJUST MAIN

BRUSH PATTERN 3-45. . . . . . . . . . . . . . . .SIDE BRUSH 3-46. . . . . . . . . . . . . . . . . . . . . . . . . .

TO REPLACE SIDE BRUSH 3-47. . . . . . . . . .

PageSKIRTS AND SEALS 3-49. . . . . . . . . . . . . . . . . . . . . .

HOPPER LIP SKIRTS 3-49. . . . . . . . . . . . . . . . . .TO REPLACE HOPPER LIP SKIRTS 3-49. .

BRUSH DOOR SKIRTS 3-49. . . . . . . . . . . . . . . . .TO REPLACE AND ADJUST BRUSH

DOOR SKIRTS 3-49. . . . . . . . . . . . . . . . . . .REAR SKIRTS 3-50. . . . . . . . . . . . . . . . . . . . . . . . .

TO REPLACE AND ADJUST REARSKIRTS 3-50. . . . . . . . . . . . . . . . . . . . . . . . .

HOPPER SIDE SKIRTS 3-51. . . . . . . . . . . . . . . . .TO REPLACE AND ADJUST HOPPER

SIDE SKIRTS 3-51. . . . . . . . . . . . . . . . . . . .MAIN BRUSH DOOR SEALS 3-52. . . . . . . . . . . .HOPPER SEALS 3-52. . . . . . . . . . . . . . . . . . . . . . .HOPPER DOOR SEALS 3-52. . . . . . . . . . . . . . . .HOPPER COVER SEAL 3-53. . . . . . . . . . . . . . . .HOPPER VACUUM FAN SEAL 3-53. . . . . . . . . . .

BRAKES AND TIRES 3-54. . . . . . . . . . . . . . . . . . . . . .SERVICE BRAKES 3-54. . . . . . . . . . . . . . . . . . . . .

TO BLEED THE BRAKES 3-54. . . . . . . . . . . .PARKING BRAKES 3-54. . . . . . . . . . . . . . . . . . . . .TIRES 3-55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE

3-3365 MM173 (3--90)

RECOMMENDED FIRST 50-HOUR MACHINE INSPECTION

After the first 50 hours of operation, the followingprocedures are recommended:

1. Check the brush pattern for correct brushadjustment.

2. Change the hydraulic fluid filter element.

3. Machines below serial number 007000: Checkdistributor ignition timing.

4. Machines below serial number 007000: Torquethe cylinder head bolts to the properspecification.

5. Perform all 50-hour interval lubrication andmaintenance procedures listed in theMaintenance chart.

MAINTENANCE

365 MM173 (3--90)3-4

MAINTENANCE CHART

10119876543

2

1

21

20

19

18 1716

15 14 12

13

16

108 11

03766

No. ofService

Interval Key Description Procedure Lubricant Points

Daily 7 Engine air filter Check service indicator -- 1Empty dust cup -- 1

4 Engine crankcase Check oil level EO 116 Dust skirts Check for damage, wear, and

adjustment -- 714 Main brush Check for damage, wear, and

adjustment -- 112 Side brush Check for damage, wear, and

adjustment -- 1

50 Hours 4 Engine crankcase Change oil and filter element EO 114 Main brush Rotate end-for-end -- 1

100 Hours 8 Dust seals Check for wear or damage -- 159 Hopper dust filter Inspect and clean or replace -- 11 Radiator Check coolant level WG 1

Clean exterior -- 120 Hydraulic fluid reservoir Check fluid level HYDO 110 Front tires Check pressure -- 221 Rear tire Check pressure -- 12 Engine fan belt (For Check tension -- 1

machines serial number007000 and above)

MAINTENANCE

3-5365 MM173 (3--90)

No. ofService

Interval Key Description Procedure Lubricant Points

200 Hours 3 Alternator belt(For Check tension -- 1machines below serialnumber 007000)

2 Engine fan belt (For Check tension -- 1machines below serialnumber 007000)

13 Side brush pivot Lubricate MPGM 117 Parking brake Check adjustment -- 119 Rear wheel support

bearing Lubricate MPGM 111 Hopper pivot Lubricate MPGM 218 Steering cylinder end Lubricate MPGM 2

400 Hours 15 Brake master cylinder Check fluid level BF 15 Engine (For machines Check and adjust valve clearance -- 8

below serial number Check and adjust idle speed -- 1007000) Check and adjust idle mixture -- 1

Clean or replace and adjustspark plugs -- 4Clean or replace and adjustdistributor points -- 1Check and adjust timing -- 1Replace PCV valve -- 1Clean PCV hoses, tubes,and fittings --Lubricate distributor felt EO 1

5 Engine (For machines Check and adjust valve clearance -- 8serial number 007000 Check and adjust idle speed -- 1and above) Check and adjust idle mixture -- 1

Clean or replace and adjustspark plugs -- 4Replace PCV valve -- 1Clean PCV hoses, tubes,and fittings --

20 Hydraulic fluid reservoir Change hydraulic fluid HYDO 16 Hydraulic fluid filter Change filter element -- 1

800 Hours 10 Front wheel bearings Repack wheel bearings MPGM 25 Engine Torque intake manifold bolts -- 51 Cooling system Flush WG 120 Hydraulic fluid reservoir Replace breather -- 1

BF -- Brake fluidEO -- Engine oilHYDO -- Tennant Company or approved hydraulic fluidMPGM -- Multipurpose, water resistant, lithium base, moly-disulphide EP greaseWG -- Water and permanent-type ethylene glycol antifreeze, one-to-one ratio

NOTE: More frequent intervals may be required in extremely dusty conditions.

MAINTENANCE

365 MM173 (3--90)3-6

LUBRICATION

ENGINE

Check the engine oil level daily. Change the engine oiland oil filter after every 50 hours of operation. Useonly SAE-SE/SF rated engine oil.

The following SAE-SE/SF rated oil grades arerecommended for engines during changing seasonaltemperatures:

MULTI-VISCOSITY OILSBelow 32_F --10_ to 90_F --10_ to above 90_F Above 10_F(Below 0_C) (--23_ to 32_C) (--23 to above 32_C) (Above --12_C)

5W 30 10W 30 10W 40 20W 40

SINGLE VISCOSITY OILS--10_ to 32_F 10_ to 60_F 32_ to 90_F Above 60_F(--23_ to 0_C) (--12_ to 16_C) (0_ to 32_C) (Above 16_C)

10W 20W 20 30 40

The engine oil capacity is 3.5 qt (3.3 L) including theoil filter.

HOPPER PIVOT

The hopper pivot is near the front of the machine.Lubricate the pivot by applying a multipurpose, waterresistant, lithium base, moly-disulphide EP grease tothe two grease fittings after every 200 hours ofoperation.

A

B

03765

HOPPER PIVOT

A. Hopper PivotB. Grease Fitting

SIDE BRUSH PIVOT

The side brush mechanism pivots on a shaft near theinside right front corner of the machine. Lubricate theshaft by applying a multipurpose, water resistant,lithium base, moly-disulphide EP grease to the greasefitting after every 200 hours of operation.

A

B

02158

SIDE BRUSH PIVOT

A. Side Brush PivotB. Grease Fitting

MAINTENANCE

3-7365 MM173 (3--90)

REAR WHEEL SUPPORT

The rear wheel support pivots the rear wheel.Lubricate the rear wheel support bearing by applyinga multipurpose, water resistant, lithium base,moly-disulphide EP grease to the grease fitting afterevery 200 hours of operation.

A

B

C

02160

REAR WHEEL SUPPORT AND STEERING

A. Rear Wheel SupportB. Steering Cylinder EndC. Grease Fitting

STEERING CYLINDER ENDS

The steering cylinder ends pivot the rear wheelsupport. Lubricate the cylinder ends by applying amultipurpose, water resistant, lithium base,moly-disulphide EP grease to the grease fittings afterevery 200 hours of operation.

FRONT WHEEL BEARINGS

The front wheel bearings support the front half of themachine. They should be repacked with multipurpose,water resistant, lithium base, moly-disulphide EPgrease after every 800 hours of operation.

MAINTENANCE

365 MM173 (3--90)3-8

HYDRAULICS

HYDRAULIC FLUID

TENNANTr Hydraulic Fluid is a speciallycompounded oil with the following features not foundin many hydraulic fluids:

1. Flat viscosity curve.

2. Additives to prevent corrosion.

3. Additives to prevent oxidation.

4. Rust inhibitors.

5. Foam suppressors.

These features restrict foaming of the hydraulic fluidand provide a high standard of lubrication to thecomponents.

TENNANT HYDRAULIC FLUIDVISCOSITY SPECIFICATIONS

TENNANT Hyd. Fluid TENNANT Hyd. FluidNo. 32397 (HP1040) No. 32398 (HP2060)

SUS @ 100_ F (38_ C) 404--445 940--1010

SUS @ 210_ F (99_ C) 78--84 122--130

TENNANT Hydraulic Fluids have a very flatviscosity curve (synonymous with “high viscosityindex”). The flat viscosity curve means that thethickness of the fluid is very constant over widetemperature ranges.

Hydraulic fluid with the viscosity rating of HP1040should be used in machines that are operated inareas which have ambient temperatures up to90_ F (32_ C). Use the HP2060 rated hydraulicfluid in areas which have ambient temperatures above90_ F (32_ C).

If a locally-available hydraulic fluid is preferred, or ifproducts of only one oil company are used, thehydraulic fluid used must match closely the viscosityspecifications given in the chart for TENNANTHydraulic Fluid, as well as the other featuresdescribed. Do not substitute automatic transmissionfluid for hydraulic fluid.

ATTENTION! Hydraulic components depend onsystem hydraulic fluid for internal lubrication. Ifdirt or other contaminants are allowed to enterthe hydraulic system, malfunctions, acceleratedwear, and damage will result.

HYDRAULIC FLUID RESERVOIR

Hydraulic fluid is stored in the hydraulic fluid reservoir.The reservoir holds up to 5.3 gal (20 L) of hydraulicfluid. The reservoir is located under the operator seat.

The reservoir is equipped with a breather-filler capand fluid level dipstick mounted on the filler neck. SeeHYDRAULIC FLUID RESERVOIR BREATHER forbreather service information.

A

B

02160

HYDRAULIC FLUID RESERVOIR

A. Filler NeckB. Breather-Filler Cap

The hydraulic fluid level dipstick is built into thebreather-filler cap. The end of the dipstick is markedwith “FULL” and “ADD” levels. This indicates the levelof hydraulic fluid in the reservoir.

MAINTENANCE

3-9365 MM173 (3--90)

Check the hydraulic fluid level after every100 hours of operation. It should be above the “ADD”marks on the dipstick, but not above the “FULL” markwhen the hydraulic fluid is warm.

FULLADD 4 QT.

A

BC

02164

HYDRAULIC FLUID LEVEL DIPSTICK

A. DipstickB. “FULL” RangeC. “ADD” Range

Do not overfill the hydraulic fluid reservoir. Thehydraulic fluid expands as it heats to its normaloperating temperature. Always allow for expansionwhen filling the reservoir.

ATTENTION! Do not overfill the hydraulic fluidreservoir or operate the machine with a low levelof hydraulic fluid in the reservoir. Damage to themachine hydraulic system may result.

Drain, flush, and refill the hydraulic fluid reservoir withhydraulic fluid after every 400 hours of operation.

TO DRAIN HYDRAULIC FLUID RESERVOIR



2. Raise the operator seat.

3. Allow the hydraulic fluid to cool.

4. Loosen the breather-filler cap. Remove thereservoir drain plug located on the bottom of thereservoir to drain the hydraulic fluid. Discard theused hydraulic fluid.

NOTE: Always change the hydraulic fluid filter whendraining the hydraulic fluid reservoir.

A

B

C02165

HYDRAULIC FLUID RESERVOIR DRAIN PLUG

A. Right Rear of MachineB. Hydraulic Fluid ReservoirC. Drain Plug

5. Flush the reservoir with clean hydraulic fluid orsuitable solvent. Do not use gasoline, kerosene,or diesel fuel.

6. Reinstall the reservoir drain plug andbreather-filler cap.

7. Lower the operator seat.

TO FILL HYDRAULIC FLUID RESERVOIR

1. Raise the operator seat.

2. Remove the reservoir breather-filler cap.

3. Pour 5 gal (19 L) of new, approved hydraulicfluid through a 200 mesh screened funnel andinto the reservoir filler neck.

ATTENTION! Use only new, approved hydraulicfluid to fill the hydraulic fluid reservoir.

4. Check the hydraulic fluid level in the reservoirwith the reservoir dipstick.

MAINTENANCE

365 MM173 (3--90)3-10

5. Add hydraulic fluid until the level in the reservoiris between the “ADD” and the “FULL” range. Donot overfill.

NOTE: Do not overfill the hydraulic fluid reservoir. Ashydraulic fluid heats to its normal operatingtemperature, it expands. Always allow for thisexpansion when filling the hydraulic fluid reservoir.

6. Place the reservoir breather-filler cap securelyon the reservoir filler neck.

7. Lower the operator seat.

8. Start engine and operate all of the hydrauliccomponents. Then recheck the hydraulic fluidlevel.

HYDRAULIC FLUID RESERVOIR BREATHER

The hydraulic fluid reservoir is equipped with abreather. The breather relieves excess atmosphericpressure or vacuum in the reservoir. The breather ismounted on the hydraulic fluid reservoir filler necklocated under the operator seat. The breather shouldbe replaced after every 800 hours of operation.

A

B

02160

RESERVOIR BREATHER-FILLER CAP

A. Filler NeckB. Breather-Filler Cap

HYDRAULIC FLUID FILTER

The machine hydraulic system is kept clean to a levelof 10 microns by a hydraulic fluid filter. The hydraulicfluid filter is located in the left front of the machineengine compartment.

Replace the hydraulic fluid filter element after the first50 hours of operation and then after every 400 hoursof operation.

TO REPLACE HYDRAULIC FLUID FILTERELEMENT



2. Open the side engine access door.

A

B

02166

HYDRAULIC FLUID FILTER

A. Hydraulic Fluid Filter ElementB. Engine

3. Unthread and discard the hydraulic fluid filterelement.

NOTE: Discard all hydraulic fluid drained from thesystem. Drained hydraulic fluid may contain foreignmaterial harmful to the hydraulic system.

4. Apply a thin coat of hydraulic fluid to the seal ofthe new hydraulic fluid filter element.

5. Thread and hand tighten the new hydraulic fluidfilter element on the filter head.

6. Operate the machine and check for leaks.Correct any leaks found.

7. Check the hydraulic fluid reservoir level and fillas required.

8. Close the side engine access door.

MAINTENANCE

3-11365 MM173 (3--90)

DIRECTIONAL PEDAL

The directional pedal controls the flow of hydraulicfluid to the hydraulic drive motor. The pedal has threepositions: “forward,” “neutral,” and “reverse.” The“forward” and “reverse” positions send hydraulic fluidto the drive motor to propel the machine.

The “neutral” position is the position in which thepropelling pump sends no hydraulic fluid to thepropelling motor. The machine should not creep whenthe “neutral” position is correctly adjusted. Adjust thepedal linkages whenever the machine creeps or afterreplacing the hydraulic propelling pump or pumplinkages. The pedal linkages should also be adjustedwhenever the reverse speed seems excessive orinadequate. The pedal linkage also includes a speedlimiter. It limits forward speed to 2 mph (3.2 km/h)whenever the hopper is raised.

TO ADJUST DIRECTIONAL PEDAL LINKAGE



2. Block the machine tires and jack up the rear ofthe machine at the designated location.


up.

3. Block up the machine with jack stands near thedesignated jacking locations. Make sure the reartire clears the floor by 2 in (50 mm) and allobstacles within a 24 in (610 mm) radius.



4. Remove side engine access door.

5. Loosen the centering spring bracket retentionbolts and adjustment bolt jam nut.

A

BC

DE

F

02167

CENTERING SPRINGS

A. Centering SpringsB. Pump Pintle ArmC. Adjustment BoltD. Stationary BracketE. Retaining BoltF. Spring Bracket

6. Adjust the position of the spring bracket andadjustment bolt so the hydraulic pump pintle armis held in a vertical position.

7. Snug the retention bolts.


9. Move the directional control pedal into the“forward” position and release it. The rear wheelshould stop rotating as soon as the pedal isreleased. Adjust the spring bracket as required.

10. Move the directional control pedal into the“reverse” position and release it. The rear wheelshould stop rotating as soon as the pedal isreleased. Adjust the spring bracket as required.

MAINTENANCE

365 MM173 (3--90)3-12

11. Stop the engine. Tighten the bolts.

12. Replace side engine access door.

13. Raise the rear of the machine, remove the jackstands, and lower the machine.

14. Loosen the bolt connecting the directionalcontrol pedal to the control linkage.

A

B

02168

DIRECTIONAL CONTROL PEDAL

A. Control PedalB. Adjustment Bolt

15. Adjust the position of the directional controlpedal so it will contact the floor when it ispressed backward. In this position the machineshould not travel backward faster than 2.5 mph(4 km/h).

16. Tighten the directional control pedal bolt.

17. Start the engine and raise the hopper.

18. Engage the hopper support bar.



20. Adjust the speed limiter cable so the cam underthe directional control pedal is rotated 10_ pastvertical toward the rear of the machine. Slide thecam assembly forward or backward to allow fullforward speed with the hopper down. Recheckthe cable adjustment for limited forward speedwith the hopper up.

AB

03776

SPEED LIMITER CAM

A. CamB. Directional Control Pedal

MAINTENANCE

3-13365 MM173 (3--90)

HYDRAULIC FLUID LEAKS

Fluid escaping at high pressure from a very small holecan be almost invisible and can cause seriousinjuries. Use a piece of cardboard or wood, ratherthan hands, to search for suspected leaks.

A

C

B

00002

HYDRAULIC PINHOLE LEAK

A. CardboardB. Pinhole LeakC. Magnifying Glass

If injured by escaping hydraulic fluid, see a doctor atonce. Serious infection or reaction can develop ifproper medical treatment is not administeredimmediately.

WARNING: Leaking hydraulic fluid underpressure can penetrate skin. Severe

infection or death can result. Do not use body tolocate leak. Use cardboard to locate leak.

MAINTENANCE

365 MM173 (3--90)3-14

03767

HYDRAULIC SCHEMATIC

MAINTENANCE

3-15365 MM173 (3--90)

HYDRAULIC SYSTEM TROUBLESHOOTING


Bad coil at S2. Replace coil.

Bad seal at S2. Replace seal.

Bad electrical connection Remake connection.at S2.

Circuit breaker tripped CB-5. Reset circuit breaker CB-5.Look for short circuit.

Bad electrical relay M4. Replace electrical relay M4.

Hopper lift micro-switch Check connection atnot operating. micro-switch. Check adjustment of

hopper and fan inlet bracket.

Main brush micro-switch Check connections atnot operating. micro-switch on main brush handle.

Bad relief valve at R1. Replace relief cartridge R1.


Cartridge stuck open at S3. Replace cartridge.

Bad electrical connection Remake connection.at S3.

Two-speed rocker switch not Replace rocker switch orworking. check electrical connections.

Circuit breaker tripped CB-5. Reset circuit breaker CB-5.Look for short circuit.




Bad electrical connection Remake connectionat S4.

Hopper lift micro-switch Check connection ofnot operating. micro-switch at hopper.

Thermo-Sentryt indicator Reset Thermo-Sentryt switchtripped or replace it.

Vacuum fan rocker switch Replace rocker switch ornot operating. check electrical connections.

Relief valve R1 is stuck open. Replace valve R1

Circuit breaker tripped CB-5. Reset circuit breaker CB-5.

Main brush does not turn.Everything else works fine.

Vacuum fan does not turn.Everything else works fine.

Two speed function ofmain brush and vacuumfan does not work. Operatesat slow speed only.

Main brush and vacuum fandoes not turn. Hopper doesnot lift.

MAINTENANCE

365 MM173 (3--90)3-16


Hopper lifts slow or does not Priority flow control F2 Clean or replace control F2.lift at all. is stuck in shifted position.

Four-way, three-position Manually shift valve, if hoppersolenoid valve has bad coil, operates properly when manuallyor spool is stuck. shifted but not when electrically

shifted, check electric circuit andcoils. Replace coils or valve ifnecessary.

Relief valve R4 has Clean or replace valve R4.contamination holding poppetoff its seat.

Bad electrical connection at Remake connections at bothsolenoid valve. coils.

Side brush does not turn. Priority flow control pump Clean or replace valve inis stuck. pump or replace entire pump.




Relief valve R2 has Clean or replace R2.contamination holding poppetoff its seat.

Bad electrical connection. Remake connection.

Side brush micro-switch Check connection or replacenot operating. micro-switch at side brush handle.

Bad relay M4. Replace relay M4.

Power steering stiff. Relief valve R2 has Clean or replace valve R2.Not functioning properly. contamination holding poppet off seat.

Relief valve R3 has Clean or replace valve R3.contamination holding poppet off seat.

MAINTENANCE

3-17365 MM173 (3--90)

ENGINE

ENGINE LUBRICATION

Check the engine oil level daily. Change the engine oiland oil filter after every 50 hours of operation. Useonly SAE-SE/SF rated engine oil.

The following SAE-SE/SF rated oil grades arerecommended for engines during changing seasonaltemperatures:

MULTI-VISCOSITY OILSBelow 32_F --10_ to 90_F --10_ to above 90_F Above 10_F(Below 0_C) (--23_ to 32_C) (--23 to above 32_C) (Above --12_C)

5W 30 10W 30 10W 40 20W 40

SINGLE VISCOSITY OILS--10_ to 32_F 10_ to 60_F 32_ to 90_F Above 60_F(--23_ to 0_C) (--12_ to 16_C) (0_ to 32_C) (Above 16_C)

10W 20W 20 30 40

The engine oil capacity is 3.5 qt (3.3 L) including theoil filter.

COOLING SYSTEM

Maintaining cooling system efficiency is important.Engine temperatures must be brought up to andmaintained within the satisfactory range for efficientoperation. However, the engine must be kept fromoverheating in order to prevent damage to the valves,pistons, and bearings. Check the radiator coolantlevel after every 100 hours of operation.

Use soft, clean water mixed with permanent-type,ethylene glycol antifreeze in a one-to-one ratio to fillthe cooling system. Deposits of sludge, scale, andrust prevent normal heat transfer. Flush the radiatorand the cooling system after every800 hours of operation, using a dependable cleaningcompound. Follow the mixing procedurerecommended by the compound manufacturer. This isimportant because of the difference in concentrationand composition of the cleaning compounds. Aftercleaning, flush the system with clean water.

Whenever a cooling system is badly rust-clogged, asindicated by overflow loss or abnormally highoperating temperatures, corrective cleaning byreverse flow flushing will most effectively remove theheavy deposits of sludge, rust, and scale. Thereverse flow flushing should be performedimmediately after draining the cleaning solution. Flushthe radiator first, then the engine, to allow the engineto cool as much as possible.

Engine overheating may also be caused by dirtyradiator fins. The exterior fins of the radiator can becleaned with an air hose. Clean the radiator exteriorafter every 100 hours of operation or sooner ifoperating in a dusty environment.

Blow all dust, which may have collected on theradiator, in through the grill and radiator fins, oppositethe direction of normal air flow. A tilt-out hydrauliccooler is provided to aid cleaning. Use care not tobend the cooling fins when cleaning. Clean thoroughlyto prevent caking dust.

A

B

02468

TILTED-OUT COOLER

A. RadiatorB. Hydraulic Cooler

Clean the radiator and cooler after they have cooledto avoid cracking.

The engine is equipped with a 180_ F (82_ C)thermostat. Normal engine temperature is 200_ F(93_ C); temperatures up to 220_ F (104_ C) areallowable; temperatures over 200_ F (93_ C)indicate a problem exists.

MAINTENANCE

365 MM173 (3--90)3-18

A pressure cap is used on the radiator to preventoverflow loss of water during normal operation. Thespring-loaded valve in the cap closes the outlet to theoverflow pipe of the radiator and thus seals thesystem. Pressure developing within the system raisesthe boiling point of the coolant and allows highertemperatures without overflow loss from boiling. Thepressure valve opens at 7 psi (50 kPa), allowingsteam and water to pass out the overflow pipe.

WARNING: Hot engine coolant. Scaldingcan result. Do not open radiator cap or

service cooling system until radiator and engineis cool to the touch.

ATTENTION! Never pour cold water or coldantifreeze into the radiator of an overheatedengine. Allow the engine to cool to avoidcracking the cylinder head or block. Keep theengine running while adding water.

AIR INTAKE SYSTEM

The importance of maintaining an air filter cannot beoveremphasized. Dirt ingested through improperlyinstalled, improperly serviced, or inadequate air filterelements wears out more engines than long hours ofoperation. Even a small amount of dirt will wear out aset of piston rings in just a few hours. Operating witha clogged air filter element also causes the fuelmixture to be richer, which can lead to formation ofharmful sludge deposits in the engine. Always coverthe air intake when the air filter is removed forservicing. Do not neglect servicing the air filter. Useonly approved replacement parts. Keep all other airintake components secure and in good condition toprevent entrance of unfiltered air.

Over-maintenance can cause more damage thangood. Removing the air filter element more often thanis needed allows contaminants to enter the engineunnecessarily. Clean or replace the air filter elementonly when the restriction indicator indicates excessiverestriction in the system.

AIR FILTER SERVICE INDICATOR

The air filter service indicator signals when to clean orreplace the air filter element. Check the serviceindicator daily. The red line will move on the scale asthe air filter element fills with dirt. Do not clean orreplace the air filter element until the red line reaches20 in H2O (5 kPa) and the “Service when Red”window is filled with red. The service indicator red linemay return to a lower reading on the scale when theengine is shut off. The red line will return to a correctreading when the engine is started.

Clean or replace the filter element when the serviceindicator reads 20 in H2O (5 kPa). After cleaning orreplacing the air filter element, reset the serviceindicator by pushing the reset button on the end of theindicator.

A

B

02172

AIR FILTER SERVICE INDICATOR

A. Service IndicatorB. Indicator Reset Button

AIR FILTER

The engine air filter housing includes a dust cap and adry cartridge-type air filter element. The dust capmust be emptied of dirt daily. The air filter elementmust be cleaned and inspected or replaced wheneverthe air filter service indicator reads 20 in H2O (5 kPa).The filter element must be replaced if it is damaged orhas been cleaned three times.

Service the air filter element only when the air filterservice indicator shows excessive restriction in thesystem. Do not remove the air filter element unless itis restricting air flow.

MAINTENANCE

3-19365 MM173 (3--90)

TO REPLACE AIR FILTER ELEMENT



2. Open the left side and top engine access doors.

3. Unscrew the clamp ring on the filter.

4. Remove the dust cap.

5. Empty the dust cap.

6. Remove the filter wing nut.

7. Gently pull the filter element out of the filterhousing.

A

B

C

E

F

D

02173

REMOVING AIR FILTER ELEMENT

A. Filter HousingB. Clamp RingC. Filter ElementD. Wing NutE. Dust CapF. Safety Air Filter Element

NOTE: Machines with heavy-duty air cleaneraccessory have a safety filter element. The safetyfilter element should be replaced, not cleaned, afterthe regular element has been damaged or has beencleaned three times.

8. Clean the interior of the air cleaner housing witha damp cloth. Clean the element housingsealing surfaces.

9. Using an air hose, direct dry, clean air maximum30 psi (205 kPa) up and down pleats on theinside of the filter. Do not rap, tap, or pound dustout of the element.



A

B

00051

CLEANING AIR FILTER ELEMENT

A. Air HoseB. Filter Element

MAINTENANCE

365 MM173 (3--90)3-20

10. After cleaning the air filter element, inspect it fordamage by placing a bright light inside. Theslightest rupture requires replacement of thefilter. Clean and inspect the seals on the ends ofthe element. They should be unbroken andflexible. Remember, the element must bereplaced after it has been cleaned three times.

B

A

03500

INSPECTING AIR FILTER ELEMENT

A. Bright LightB. Filter Element

11. Install the new or cleaned filter element so thefins on the element are at the intake end of theair cleaner. Use care so the fins are notdamaged. Make sure the element is seatingevenly. Tighten the filter wing nut.

12. Install the dust cap with the arrows pointing up.Tighten the clamp ring to hold it in place. Checkall intake hose connections for leaks orabrasion.

A02492

DUST CAP

A. Dust Cap

13. Reset the air filter service indicator.

14. Close the access doors.

MAINTENANCE

3-21365 MM173 (3--90)

FUEL SYSTEM -- GASOLINE

FUEL FILTER

The fuel filter traps fuel impurities. The filter is locatedbear the fuel tank. Replace the fuel filter whenneeded.

CARBURETOR

The carburetor has two basic adjustments. Thoseadjustments are idle fuel mixture and idle speed.Check and adjust idle fuel mixture and idle speedafter every 400 hours of operation. The idle fuelmixture is controlled by a screw located on the front ofthe carburetor. Turning the screw in, clockwise, leansthe fuel mixture. Turning the screw counterclockwise,richens the fuel mixture.

FOR SAFETY: When servicing machine: avoidmoving parts. Do not wear loose jackets, shirts,or sleeves when working on machine.

The idle speed is controlled by a screw located on theside of the carburetor next to the throttle linkage.Turning the screw clockwise increases engine speed.Turning the screw out, counterclockwise, decreasesengine speed. Proper idle speed is 950 + 50 rpm withall accessories in the “off” position.

A

B

05509

CARBURETOR ADJUSTING SCREWS

A. Idle Fuel Mixture Adjusting ScrewB. Idle Speed Adjusting Screw



FUEL SYSTEM -- LPG

LPG FUEL SYSTEM

The liquid withdrawal LPG fuel system consists of fivecomponents which are: the LPG fuel tank, pressurerelief valve, fuel filter lock, vaporizer-regulator, andthe carburetor.

Liquid LPG fuel flows from the LPG tank, under itsown pressure, to the pressure relief valve. This valveis normally closed, preventing LPG fuel from escapinginto the atmosphere. The valve opens to relievepressure if the fuel pressure exceeds system limits.From the pressure relief valve, the liquid LPG fuel ispiped to the fuel filter lock. The fuel filter lock filtersunwanted tank scale and deposits out of the LPGfuel. The fuel filter lock also stops the flow of LPG fuelwhen the engine is not operating. The oil pressureswitch controls the fuel filter lock. When the engine oilpressure is4 psi (30 kPa) or greater, the oil pressure switchpermits an electrical current to open the fuel filter lockwhich allows LPG fuel to flow on to thevaporizer-regulator. The oil pressure switch isbypassed when the engine is being started, allowingLPG fuel to flow.

The vaporizer section of the vaporizer-regulatorconverts the liquid LPG fuel into a gaseous LPG fuel.From the vaporizer section, the gaseous LPG fuel issent to the primary regulator section of thevaporizer-regulator. The primary regulator sectionreduces the pressure of the LPG fuel. The secondaryregulator section reduces the LPG fuel pressure tothe level required by the carburetor. From thevaporizer-regulator, the LPG fuel is sent to thecarburetor where it is finally metered into the air flowwhich is sent to the engine combustion chamber.

A B

C

D

E

FG03511

LPG FUEL SYSTEM

A. CarburetorB. Vaporizer-RegulatorC. Fuel Filter LockD. Pressure Relief ValveE. Tank Service ValveF. LPG Fuel TankG. Oil Pressure Switch

MAINTENANCE

365 MM173 (3--90)3-22

Never operate an LPG powered machine if the LPGfuel system is leaking, or if any component in the fuelsystem is malfunctioning. Operating the machineunder either of these conditions may cause a fire orexplosion.

Check for frosting. If frosting occurs on or near anyLPG component, there is a possibility of an LPG fuelleak or a malfunctioning component. To locate theleak, apply a soapy water solution to the suspectedarea. Watch for forming bubbles in the suspectedarea. This area may have an LPG fuel leak. Repair orreplace the part. Use Loctite brand Stainless SteelPST thread sealant when reassembling. Thisepoxy-type sealant is not affected by aging or highhumidity. Be sure to follow application directions andapply proper torque when reconnecting fittings. Neverbypass safety components except to test. If the safetycomponents are defective, replace them beforeoperating the machine.

Check routings of all LPG hoses. Keep them awayfrom sharp edges, exhaust manifolds, or other hotsurfaces. Check for signs of abrasion or deterioration.Replace hoses found to be worn or damaged.

FUEL TANKS

The LPG fuel tanks should be inspected for sharpdents, gouges, leaks, and broken protecting ringswhenever the tanks are refilled. All tank valves mustbe inspected for leaks using a soap solution. Valvesmust also be checked for dirt, paint, or other debris inthe valve openings. The following specific checksmust also be made:

Filler Valve -- Check for proper functioning and thepresence of the handwheel. Valve must be closedexcept during filling.

Vapor and Liquid Tank Service Valves -- Check forproper functioning and presence of the handwheel.The valve must be closed except when in service.

Tank Service Valve Coupling -- Check for properfunctioning, thread condition, and damaged ormissing washers or o-rings.

Safety Relief Valve -- Check for damage. Check forthe presence of the relief valve elbow and the properdirection of the elbow. If the rain cap is missing, checkfor foreign matter and replace the rain cap. Do nottamper with the relief valve setting.

Magnetic Liquid Level Gauge -- Check operationagainst the maximum filling point as determined byweight.

D

CA

B

E

03485

TYPICAL LPG LIQUID WITHDRAWAL FUEL TANK

A. Filler ValveB. Safety Relief ValveC. Liquid Tank Service ValveD. Magnetic Liquid Level GaugeE. Tank Service Valve Coupling

An LPG fuel tank with any of the stated defects mustbe removed from service and be repaired ordestroyed accordingly.

If an LPG fuel tank is damaged or leaking, it shouldbe removed to a designated safe area, and the properpersonnel should be notified. Do not attempt to makerepairs to the tank, regardless of condition. Repairs ordisposal must only be made by qualified personnel.

The care an LPG fuel tank receives has a directbearing on how long that tank can be used safely.LPG fuel tanks must not be dropped or draggedacross any surface. To move LPG fuel tanks, use ahand truck or roll the tank on its foot ring while it isbeing held in a position slightly off vertical.

Whether the storage is inside or outside, fuel tanksshould not be stored in the vicinity of combustiblematerials or high temperature sources such as ovensand furnaces, since the heat may raise the pressureof the fuel to a point where the safety relief valveswould function. Take care to insure that the tanks arestored in such a way that if the safety relief valves dofunction, they will relieve vapor, rather than liquid.

Valves on empty tanks must be closed during storageand transportation.

MAINTENANCE

3-23365 MM173 (3--90)

Similar precautions should be taken in storingmachines fitted with LPG fuel tanks. The machinesmay be stored or serviced inside buildings, providedthere are no leaks in the fuel system and the tanksare not overfilled. While machines are being repairedinside a building, the shut-off valve on the tank mustbe closed, except when the engine must be operated.

Changing the tank is a chance for the machineoperator to carefully check the tank, fittings, and thefuel lines and fittings. If abnormal wear is detected,the operator should report the findings to theappropriate personnel.

TO CHANGE AN LPG FUEL TANK

1. Park the machine in a designated safe area. Setthe machine parking brake.


2. Close the tank service valve.

3. Operate the engine until it stops from lack offuel.



4. Put on gloves and remove the quick-disconnecttank coupling.

WARNING: LPG fuel is very cold. Frostbitecan result. Wear gloves when connecting

or disconnecting LPG hoses.

5. Inspect the LPG fuel lines for wear or damage.

6. Remove the empty LPG fuel tank from themachine.

7. Check the tank for damage or wear.

8. Store the tank in a designated safe area.

9. Select a filled LPG fuel tank and inspect it fordamage or leaks.

NOTE: Make sure the LPG fuel tank matches the fuelsystem (liquid tank with liquid system).

10. Carefully place the LPG tank in the machine sothat the tank centering pin enters the aligninghole in the tank collar.

NOTE: If the pin cannot be engaged, make sure youhave the correct LPG fuel tank and then adjust the pinlocator in or out.

11. Fasten the tank hold-down clamp to lock thetank in position.

12. Connect the LPG fuel line to the tank servicecoupling. Make sure the service coupling isclean and free of damage. Also make sure itmatches the machine service coupling.

13. Open the tank service valve slowly and checkfor leaks. If an LPG leak is found, close theservice valve immediately and notify theappropriate personnel.

14. If no leaks are found, the engine is ready tostart.

FUEL FILTER LOCK

The fuel filter lock filters the LPG fuel. The fuel filterlock also stops the flow of LPG fuel to the enginewhen the engine is not operating, or when the engineoil pressure is less than 4 psi (30 kPa).

Replace the fuel filter lock filter pack with the filterpack replacement kit if diminished gas flow indicatesthe filter is clogged. A drain plug is provided forpurging the filter bowl. Clean out the bowl whenreplacing the filter pack.

VAPORIZER-REGULATOR

If any malfunction is noted, completely disassemblethe vaporizer-regulator. Clean all of the parts inalcohol. Inspect all of the parts and replace whereneeded. Carefully reassemble the vaporizer-regulatorwith the seal repair kit. Check for proper operation.

CARBURETOR

If any malfunction is noted, completely disassemblethe carburetor. Clean all of the parts in alcohol.

Inspect all of the parts and replace when needed.Carefully reassemble the carburetor with the sealrepair kit.

MAINTENANCE

365 MM173 (NIL)3-24

OIL PRESSURE SWITCH

The engine oil pressure switch requires no regularmaintenance. Never bypass the oil pressure switch asthis is a safety feature which prevents LPG fuel fromflowing when the engine is not operating properly.

LPG FUEL TROUBLESHOOTING


Engine will not start. Out of fuel. Replace fuel tank with full one.

Service valve opened too Close valve and reopen slowly.quickly -- engaging safety valve.

Plugged fuel filter. Replace filter.

Kinked or restricted fuel line. Straighten or replace fuel line.

Engine out of tune. Tune-up engine.

Oil pressure switch failure. Replace oil pressure switch.

Fuel lock valve failure. Repair or replace fuel filter lock.

Vaporizer-regulator failure. Repair or replace vaporizer --regulator.

Engine runs unevenly Wrong type of fuel Replace vapor withdrawal tankor lacks power. tank -- vapor withdrawal tank. with liquid withdrawal tank.

Plugged fuel filter lock. Replace filter pack.

Kinked or restricted fuel line. Straighten or replace fuel line.

Engine out of tune. Tune-up engine.

Restricted air filter. Clean or replace air filter element.

Vaporizer-regulator out of Adjust vaporizer-regulator.adjustment.

MAINTENANCE

3-25365 MM173 (3--90)

GOVERNOR (For machines below serial number007000)

The governor controls engine speed. It is driven by abelt which spans the crankshaft sheave.

The governor is oil filled. It requires no regularinspections. Change the oil when performing majorengine work. Use an SAE rated 10W30 or 10W40engine oil.

A

B

CD

E

F

G03723

GOVERNOR

A. High Speed Stop ScrewB. Oil Fill PlugC. GovernorD. Surge ScrewE. Regulation ScrewF. Throttle RodG. Oil Level Plug

The governor is factory set and should not beadjusted unless the engine speed varies from thespecification or if the engine surges. The governorshould be set so the engine operates at2400 + 50 rpm at “full” speed setting under load. Asurge screw has been provided to compensate forsurging — adjust it with care or governor damagemay result. The regulation screw has been factory setand should not be tampered with.

TO ADJUST GOVERNOR (For machines below serialnumber 007000)

1. Operate the engine until it reaches normaloperating temperature.

2. Park the machine on a level surface, stop theengine, and set the machine parking brake.


3. Check the fan belt tension as described inENGINE FAN BELT (For machines below serialnumber 007000).

4. Place the throttle control lever in the “high”position. There should be a 0.03 to 0.06 in (1 to2 mm) space between the carburetor lever andthe lever stop. Adjust the throttle rod asrequired.

5. Move the throttle control lever to the “idle”position. Start the engine and adjust the engineidle speed screw so the engine operates at 950+ 50 rpm.

6. Lower and start the main brush and side brushrotating. Adjust the high speed stop screw sothe engine operates at 2350 rpm. Then adjustthe surge screw to bring the engine speed to2400 rpm. Tighten all locknuts.


7. Stop the engine.

8. Check and adjust the throttle cable position toallow full linkage movement.

GOVERNOR (For machines serial number 007000and above)

The electronic governor controls engine speed. Thegovernor consists of a control box located to the leftof the operator under the throttle switch, and anactuator mounted on the engine. The control boxregulates the actuator, which in turn controls thethrottle.

The electronic governor is factory set and is not userserviceable.

MAINTENANCE

365 MM173 (3--90)3-26

ELECTRICAL SYSTEM

SPARK PLUGS

Clean or replace and adjust spark plugs after every400 hours of operation. A wire gauge is best forchecking the spark plug gap. A flat gauge should notbe used unless the electrode surfaces have beenbeen dressed with a small file to get parallel surfacesbetween the center and side electrodes. Set the sparkplug gap by bending the side electrode. All sparkplugs, new or used, should have the gaps checkedand reset if necessary.

A

B

D

c

01174

GAPPING THE SPARK PLUG

A. Spark PlugB. Gapping ToolC. Side ElectrodeD. Center Electrode

The proper spark plug gap is 0.032 in (0.8 mm) formachines below serial number 007000. The properspark plug gap is 0.039 in (1 mm) for machines serialnumber 007000 and above.

To get good performance from the spark plugs, followthese steps when installing the plugs:

1. Clean the spark plug seat in the cylinder head.

2. Use a new seat gasket and screw the plug in byhand.

3. Tighten the spark plugs to 22 to 28 ft lb(30 to 38 Nm) with a socket wrench of thecorrect size.

DISTRIBUTOR (For machines below serial number007000)

The distributor operation is vital to the operation of theengine. The following items should be carefullyinspected after every 400 hours of normal operation;however, dirt, dust, water, and high speed operationmay cause more rapid wear and necessitate morefrequent inspections:

1. Remove the distributor cap. Clean the cap andexamine for cracks, carbon runners, or corrodedterminals. If the vertical faces of the inserts areburned, install a new cap. If the horizontal facesof the inserts are burned, replace the cap andthe rotor as this condition is caused by the rotorbeing too short.

NOTE: If replacing the rotor, be sure to use anoverspeed rotor as indicated in the parts manual or itmay damage the engine if the governor fails.

2. Check the centrifugal advance mechanism for“freeness” by turning the breaker cam in thedirection of rotation and then releasing it. Theadvance springs should return the cam to itsoriginal position.

3. Lubricate the shaft felt, advance mechanism,breaker cam, and pivot. Make sure the breakerarm moves freely on its hinge. Special grease(with Moly) should be used sparingly on thebreaker cam.

NOTE: Avoid excessive lubrication. Excess lubricantmay get on the contact points and cause burning.

MAINTENANCE

3-27365 MM173 (3--90)

4. Clean and check or replace the ignition pointsand gap. If the points are pitted, burned, or wornto an unserviceable condition, install a new setof points. Badly pitted points may be caused bya defective or improper condenser capacity.

If the points are serviceable, they should bedressed down with a fine cut stone or point file.The file must be clean and sharp; never useemery cloth to clean contact points.

After filing, check the point gap and reset to0.025 in (0.6 mm), 48_ to 52_ dwell. Thebreaker arm must be resting on the high point ofthe cam during this operation.

When replacing points, make sure they arealigned and make full contact. Bend thestationary arm to obtain proper alignment; donot bend the breaker arm.

TO REPLACE IGNITION POINTS (For machinesbelow serial number 007000)

1. Remove the distributor cap and the rotor.

2. Disconnect the condenser wire from the ignitionpoint assembly.

A

B

C

D

E

00694

INSTALLING IGNITION POINTS

A. Retaining LockscrewB. PinC. Ignition Point AssemblyD. HoleE. Advance Plate

3. Remove the ignition points attaching screw andlift out the ignition point assembly.

4. Remove the condenser by removing the screwattaching the condenser to the distributor plate.

5. Install the new condenser.

6. Position the new ignition points on the advanceplate and install the attaching screw.

7. Connect the condenser wire to the ignitionpoints.

8. Adjust the ignition points to 0.025 in(0.6 mm). The dwell angle is 48_ to 52_.

A

B

C

D

E

00695

ADJUSTING IGNITION POINTS

A. ScrewdriverB. Screwdriver BladeC. LockscrewD. SlotE. Boss

9. Replace the distributor cap and the rotor.

NOTE: If replacing the rotor, be sure to use anoverspeed rotor as indicated in the parts manual orthe engine will overspeed if the governor or governorbelt fails.

MAINTENANCE

365 MM173 (3--90)3-28

DISTRIBUTOR IGNITION TIMING (For machinesbelow serial number 007000)

The distributor ignition timing must be checked with atiming light, using the timing points located on thefront of the engine and the timing marks located onthe crankshaft pulley. Distributor ignition timing shouldbe checked after the first 50 hours of operation andafter every 400 hours of operation thereafter.

To check and adjust the ignition timing with a scope,refer to the scope manufacturer’s instructions. Tocheck and adjust the timing with a timing light,proceed as follows:

TO CHECK AND ADJUST DISTRIBUTOR IGNITIONTIMING (For machines below serial number 007000)

NOTE: Dwell angle must be correct or timing will notbe accurate.



2. Clean and mark the timing marks.

NOTE: Painting a white line on the front pulley timingmarks will make them easier to see under the timinglight.

3. Disconnect and plug the vacuum hose from thedistributor.

A

B

00696

ENGINE TIMING MARKS

A. Timing PointerB. Crankshaft Pulley

4. Connect the timing light to the No. 1 cylinderspark plug wire. Connect a tachometer to theengine.


5. Start the engine and reduce the idle speed to600 rpm to be sure that the centrifugal advanceis not operating. Adjust the initial ignition timingto 10_ to 12_ BTDC on gasoline engines,and 12_ to 14_ BTDC on LPG engines.

To advance the timing, turn the distributor bodyclockwise. To retard the timing, turn thedistributor body counterclockwise.

6. Check the centrifugal advance for properoperation by starting the engine andaccelerating it to approximately 2000 rpm. If theignition timing advances, the centrifugaladvance mechanism is functioning properly.Note the engine speed when the advancebegins and the amount of total advance. Stopthe engine.

7. Unplug the vacuum line and connect it to thedistributor vacuum advance unit. Start theengine and accelerate it to approximately 2000rpm. Note the engine speed when the advancebegins and the total amount of advance.Advance of the ignition timing should beginsooner and advance farther than when checkingthe centrifugal advance alone. Stop the engine.

8. If the vacuum advance is not functioningproperly, remove the distributor and check it ona distributor tester.

9. After adjusting timing, be sure to increase theengine idle speed to its normal setting.

MAINTENANCE

3-29365 MM173 (3--90)

ENGINE IGNITION TIMING (For machines serialnumber 007000 and above)

The ignition system does not require any mechanicalexternal adjustments, however the spark plug hightension leads must be inserted correctly, if everremoved, at each numbered coil position to thecorresponding spark plug number in the cylinder (frontto rear #1, 2, 3, and 4).

The ESC module controls the timing position in thestart mode at 10_ BTDC until the rpm reaches250 rpm, thereafter the sensors are processed andtiming is set to be compatible with engine speed,crankshaft position, engine load, engine coolanttemperature and overspeed by the module.

CYLINDER HEAD

CYLINDER HEAD

A three-stage torque procedure should be used whenreassembling the cylinder head. The cylinder headbolts must be tightened after the first50 hours of operation, for machines below serialnumber 007000, and seasonally thereafter for allmachines.

Snug down cylinder head bolts in the propersequence; first to 20 to 30 ft lb (27 to 41 Nm), then to50 to 55 ft lb (68 to 75 Nm), and then to 65 to 70 ft lb(88 to 95 Nm).

Tighten the intake manifold bolts to 15 to 18 ft lb (20to 24 Nm) after every 800 hours of operation.

00697

CYLINDER HEAD BOLT TIGHTENING SEQUENCE

The cylinder head bolts must be retorqued after theengine is put into operation and brought up to properoperating temperatures. To retorque head bolts, followthe correct sequence. Loosen one head bolt at a timeone-quarter turn, 90 degrees; then retorque it to thecorrect value.

NOTE: Power wrench torque limit must be held atleast 10 ft lb (14 Nm) below hand torque specification;then hand torque to the specifications.

MAINTENANCE

365 MM173 (3--90)3-30

VALVE TAPPET CLEARANCE

The valve tappet clearance must be checked andadjusted if necessary after every 400 hours ofoperation.

To set the valve clearance, rotate the crankshaft untilNo. 1 cylinder is at the top of the compression stroke.Check the timing marks. It should read 0 or TDC.Both valves on No. 1 cylinder are now closed. Set thevalve clearance on both valves. Next, rotate thecrankshaft 180_, and set the valve lash on bothvalves on No. 2 cylinder. Again rotate the crankshaft180_, and set the valve lash on both valves on No. 4cylinder. Rotate the crankshaft another 180_, and setthe valve lash on both valves on No. 3 cylinder.

Check and adjust, for machines below serial number007000, the intake valve clearance from 0.008 to0.010 in (0.20 to 0.25 mm) and the exhaust valveclearance from 0.018 to 0.020 in (0.45 to 0.50 mm)while the engine is cold.

Check and adjust, for machines serial number 007000and above, the intake valve clearance from 0.009 in(0.22 mm) and the exhaust valve clearance from0.013 in (0.32 mm) while the engine is cold.

CRANKCASE VENTILATION SYSTEM

Clean the crankcase ventilation hoses, tubes, andfittings and replace the PCV valve after every400 hours of operation.

TUNE-UP CHART

Idle speed 950 + 50 rpm

Maximum governed speed,under load 2350 + 50 rpm

Maximum governed speed,no load 2700 + 100 rpm

Spark plug gap (For 0.032 in (0.8 mm)machines below serialnumber 007000)

Spark plug gap (For 0.039 in (1 mm)machines serial number007000 and above)

Ignition point gap (For 0.025 in (0.6 mm)machines below serialnumber 007000)

Dwell angle (For machines 48_ to 52_below serial number007000)

Timing (For machines 10_ to 12_ BTDCbelow serial number @ 600 rpm,007000) gasoline

12_ to 14_ BTDC@ 600 rpm, LPG

Firing order 1--2--4--3, counter--clockwise rotation

Valve clearances, cold 0.008 to 0.010 in(For machines below (0.20 to 0.25 mm)serial number 007000) intake

0.018 to 0.020 in(0.45 to 0.50 mm)exhaust

Valve clearances, cold 0.009 in(For machines serial (0.22 mm)number 007000 and above) intake

0.013 in(0.32 mm)exhaust

MAINTENANCE

3-31365 MM173 (3--90)

ELECTRICAL SYSTEM

BATTERY

The battery is rated at 12 V, 475 ccA. It is locatedunder the operator foot plate. When removing batterycables, remove the negative (--) cable before thepositive (+) cable.

Do not allow the battery to remain in dischargedcondition for any length of time. Do not operate themachine if the battery is in poor condition or with only25% of charge left.

Clean the top surface and the terminals of the batteryperiodically. Use a strong solution of baking soda andwater. Brush the solution sparingly over the batterytop, terminals, and cable clamps. Do not allow anybaking soda solution to enter the battery. Use a wirebrush to clean the terminal posts and the cableconnectors. After cleaning, apply a coating of clearpetroleum jelly to the terminals and the cableconnectors. Keep the top of the battery clean and dry.

Keep all metallic objects off the top of the battery, asthey may cause a short circuit. Replace worn ordamaged wires.

The electrolyte level in regular non-sealed batteriescan be checked. It must always be above the batteryplates. Add distilled water to maintain solution at thecorrect level above the plates, but do not overfill.Never add acid to batteries, only distilled water. Keepvent plugs firmly in place at all times, except whenadding water or taking hydrometer readings.

WARNING: Battery acid causes severeburns. Avoid contact. Wash immediately

and get medical attention if contact occurs.

If when checking battery specific gravity, one or morebattery cells tests lower than the other battery cells,(0.050 or more) the cell is damaged, shorted, or isabout to fail.

NOTE: Do not take readings immediately after addingwater -- if the water and acid are not thoroughlymixed, the readings may not be accurate. Check thehydrometer readings against this chart:

SPECIFIC GRAVITY BATTERYat 80_ F (27_ C) CONDITION

1.260 -- 1.280 100% charged1.230 -- 1.250 75% charged1.200 -- 1.220 50% charged1.170 -- 1.190 25% charged1.110 -- 1.160 Discharged

NOTE: If the readings are taken when the batteryelectrolyte is any temperature other than 80_ F(27_ C), the reading must be temperature corrected.

To determine the corrected specific gravity readingwhen the temperature of the battery electrolyte isother than 80_ F (27_ C):

Add to the specific gravity reading 0.004,4 points, for each 10_ F (5_ C) above 80_F (27_ C).

Subtract from the specific gravity reading 0.004,4 points for each 10_ F (5_ C) below 80_ F(27_ C).

MAINTENANCE

365 MM173 (3--90)3-32

03768

ELECTRICAL SCHEMATIC(For machines below serial number 007000)

MAINTENANCE

3-33365 MM173 (3--90)

03768

ELECTRICAL SCHEMATIC(For machines below serial number 007000)

MAINTENANCE

365 MM173 (3--90)3-34

03768

ELECTRICAL SCHEMATIC(For machines serial number 007000 and above)

MAINTENANCE

3-35365 MM173 (3--90)

03768

ELECTRICAL SCHEMATIC(For machines serial number 007000 and above)

MAINTENANCE

365 MM173 (3--90)3-36

BELTS AND CHAINS

ALTERNATOR BELT (For machines below serialnumber 007000)

The alternator belt is driven by the engine crankshaftsheave and drives the water pump and alternatorsheaves. Check and adjust the alternator belt tensionafter every 200 hours of operation.

To tighten the alternator belt, loosen the alternatormounting bolts and pull the alternator away from theengine until the belt is snug; then tighten the bolts. Donot use a pry bar on the alternator as it will damagethe alternator. Proper belt tension is obtained whenthe belt deflects 0.09 in (2 mm) from a force of 7 to 10lb (3 to 4.5 kg) applied at the midpoint of the longestspan.

A

B

03769

BELTS

A. Engine Fan BeltB. Alternator Belt

ENGINE FAN BELT (For machines below serialnumber 007000)

The engine fan belt is driven by the engine crankshaftsheave and drives the engine fan and governorsheaves. Check and adjust the engine fan belttension after every 200 hours of operation.

To tighten the engine fan belt, loosen the governormounting bolts, pull the governor away from theengine until the belt is snug, then tighten the bolts.Proper belt tension is obtained when the belt deflects0.25 in (6 mm) from a force of 1 to 2 lb (0.5 to 0.9 kg)applied at the midpoint of the longest span. Afteradjusting the belt check the governor adjustment asdescribed in TO ADJUST GOVERNOR (Formachines below serial number 007000).

ENGINE FAN BELT (For machines serial number007000 and above)

The engine fan belt is driven by the engine crankshaftsheave and drives the engine fan and alternator.Check and adjust belt tension after every 100 hoursof operation.

To adjust belt tension, loosen the alternator mountingbolts and pull the alternator away from the engineuntil the belt is snug; then tighten the bolts. Do notuse a pry bar on the alternator as it may damage thealternator. Proper belt tension is obtained when thebelt deflects 0.5 in (13 mm) from a force of 8 to 10 lb(4 to 5 kg) applied at midpoint of the longest span.

STATIC DRAG CHAIN

A static drag chain is provided to prevent the buildupof static electricity in the machine. The chain isattached to the machine by a rear brush skirt retainingbolt.

The chain should make contact with the floor at alltimes.

MAINTENANCE

3-37365 MM173 (3--90)

DEBRIS HOPPER

HOPPER DUST FILTER

The dust filter filters the air which is drawn up fromthe main brush compartment through the hopper. Thedust filter is equipped with a shaker motor to removethe accumulated loose dust particles. The dust filtershaker motor is operated by the vacuum fan and filtershaker switch. Shake the dust filter before dumpingthe hopper and at the end of every work shift. Inspectand clean or replace the dust filter after every 100hours of operation.

To clean the dust filter, use one of the followingmethods:

D TAPPING -- Tap the filter gently on a flat surfacewith the dirty side down. Do not damage theedges of the filter element or the filter will notseat properly in the hopper.

D AIR -- Blow compressed air, 35 psi (240 kPa)maximum, through the dust filter opposite thedirection of the arrows. This may be done withthe dust filter in the machine. Always wear eyeprotection when using compressed air.



D WATER -- Soak the dust filter in a water andmild detergent solution. Rinse the dust filter untilit is clean. The maximum water pressureallowable is 40 psi (275 kPa). Air dry the wetdust filter; do not use compressed air.

NOTE: Be sure the dust filter is dry before reinstallingit in the machine.

TO REMOVE HOPPER DUST FILTER



2. Push the hopper cover latch release lever toopen the hopper cover.

3. Disconnect the shaker motor wire connectors.

AB

C

D

C

03770

DUST FILTER SHAKER ASSEMBLY

A. Dust Filter Shaker AssemblyB. Dust FilterC. Spring Mounting BoltD. Filter Retaining Tab

4. Remove the two dust filter spring mountingbolts.

5. Loosen the six dust filter retaining tab bolts.

6. Rotate the filter retaining tabs to allow the dustfilter to be removed.

7. Lift the dust filter shaker assembly off the dustfilter element.

8. Lift the dust filter element out of the hopper.

9. Clean or discard the dust filter element asrequired.

MAINTENANCE

365 MM173 (3--90)3-38

TO INSTALL HOPPER DUST FILTER

1. Place the cleaned or new dust filter in thehopper with the arrows pointing up.

A

B

03771

INSTALLING DUST FILTER

A. Dust FilterB. Hopper

2. Rotate the retaining tabs to hold the dust filter inthe hopper.

3. Tighten the retaining tab bolts.

4. Slide the dust filter shaker assembly in positionover the dust filter.

5. Thread the two bolts through the mountingsprings and into the dust filter frame. Tighten thebolts.

6. Reconnect the shaker motor wire connectors.


THERMO-SENTRYt

The Thermo-Sentryt is a thermostat that sensesthe temperature of the air drawn into the vacuum fanfrom the hopper. The thermostat controls the solenoidvalve that directs hydraulic fluid to the vacuum fanmotor. In the event of a fire in the hopper, the high airtemperature would trip the thermostat stopping theelectric current to the solenoid valve -- stoppinghydraulic flow to the vacuum fan motor and air flow tothe fire. After the thermostat has tripped, it must bemanually reset by pushing the reset button in.

A

B

C

03777

THERMO-SENTRYt

A. Vacuum FanB. Thermo-SentrytC. Reset Button

MAINTENANCE

3-39365 MM173 (3--90)

VACUUM FAN AND MAIN BRUSH SHUT-OFFSWITCH

The vacuum fan and main brush shut-off switch stopsthe vacuum fan and main brush whenever the hopperis raised. The switch roller rides on the back of thehopper. When the hopper is raised, the switch loosescontact with the hopper and stops hydraulic flow.Adjust the switch position after adjusting the hopperor if the vacuum fan and main brush do not stop whenthe hopper is raised.

A

B

03724

SHUT-OFF SWITCH

A. SwitchB. Switch Roller

DEBRIS HOPPER

The debris hopper collects all of the debris swept upby the machine. The hopper has four areas ofadjustment. The adjustments are: hopper lift linkage,hopper stops, arm lock bracket, and hoppercentering. All of the adjustments have been made atthe factory and require no regular maintenance. In theevent that the hopper components are repaired orreplaced, the hopper must be readjusted for bestperformance.

The hopper adjustments must be made in the orderspecified. Make all adjustments with the engine offand parking brake set. If the adjustments are madewith the hopper raised, be sure to engage the hoppersafety support bar.

TO ADJUST HOPPER

NOTE: Empty the debris hopper and temporarilyremove the hopper lift linkage side panels beforemaking adjustments.

A. HOPPER LIFT LINKAGE

1. Stand clear and cycle the hopper up anddown. Watch for signs of binding,sloppiness, or misalignment of the lift armlinkage. Reshim to remove binding,sloppiness, or misalignment of the linkageas necessary.

WARNING: Stay clear of hopper lift armswhen they are in motion.

B. HOPPER STOPS

1. The two top hopper stop bolts, one on eachside, prevent the lift cylinders from overextending. Adjust the stop bolts so the liftlinkage stops against the bolts and stillallows the hopper to raise to the requiredheight.

MAINTENANCE

365 MM173 (3--90)3-40

2. The bottom stop bolts prevent the liftcylinders from bottoming. Loosen the jamnut on each down stop bolt. Thread thebolts into the frame. Extend each hydrauliccylinder 0.38 in (10 mm) from its fullyretracted position. Thread the stop bolt outof the frame until the bolt contacts thebottom of the lift linkage. Secure the stopbolt positions with the jam nuts.

C A

B

02179

STOP BOLT

A. Lift LinkageB. Stop BoltC. Hydraulic Cylinder

3. The upper arm wedge stop allowsadjustment so both upper arm slider pinscontact their stops at the same time as thehopper is being rolled out. Roll out thehopper and observe the slider pins. If theydo not top out at the same time, loosen thewedge stop bolt on the top left lift arm andmove the wedge stop to match the travel ofthe right slider pin. Tighten the wedge stopbolt and check to make sure the pins stopat the same time. Readjust as necessary.

A

B

C

02180

WEDGE STOP

A. Left Slider PinB. Wedge Stop BoltC. Wedge Stop

MAINTENANCE

3-41365 MM173 (3--90)

C. ARM LOCK BRACKET

1. The arm lock bracket locks the upper liftarm in the fully extended position when thehopper is in the raised position. Thisprevents the hopper from rolling back in theevent the operator tries to lower the hopperand it becomes jammed or hung up. Thearm lock bracket must be adjusted so itdrops and latches when the hopper israised and unlatches when the hopper islowered. Adjust the locking strip so thespring lifts the bracket as it comes incontact with the locking strip, and lowersthe bracket as it looses contact with thelocking strip.

A

B

CD

02181

DISENGAGED ARM LOCK BRACKET

A. Locking StripB. SpringC. Arm Lock BracketD. Lift Arm

A

B

C

02182

ENGAGED ARM LOCK BRACKET

A. Arm Lock BracketB. Lift ArmC. Lift Arm Stop

MAINTENANCE

365 MM173 (3--90)3-42

D. HOPPER CENTERING

1. The side-to-side and front-to-backadjustments allow the hopper to becentered in the machine. Make sure thehopper does not interfere with any otherparts when in motion. One bolt on eachside of the hopper adjusts the side-to-sideposition. Loosen both bolts before makingan adjustment. Tightening one bolt closesthe gap on that side of the hopper. Tightenboth bolts after the hopper is centeredside-to-side with respect to the hopper liftarms.

Five bolts on each side of the hopper adjustthe front-to-back position. Loosen all of thebolts, reposition the hopper, and tighten thebolts.

A

B

C

D

02183

HOPPER POSITION ADJUSTMENT BOLTS

A. HopperB. Front-to-Back Adjustment BoltsC. Hopper PivotD. Side-to-Side Adjustment Bolt

2. The hopper cover hinges and latch determinethe tightness of the hopper cover seal. Adjustthe hinges and latch so the entire seal iscompressed evenly. The hopper cover hingeshave slots to allow adjustment.

AB

02161

HOPPER COVER HINGE

A. HingeB. Hopper Cover

The latch height is adjusted by loosening,repositioning, and tightening the latchstriker. The latch position can also beadjusted by loosening, repositioning, andretightening the latch bracket mountingbolts.

A

B

C

02184

HOPPER COVER LATCH STRIKER

A. Hopper CoverB. Latch StrikerC. Mounting Bolt

MAINTENANCE

3-43365 MM173 (3--90)

3. The two rear hopper stops determine the heightof the rear of the hopper. Adjust the stop boltsso the rear of the hopper is0.31 to 0.50 in (10 to 15 mm) lower than andparallel to the relay panel cover and the valvecover panel.

B

A

03780

REAR HOPPER STOP BOLTS

A. HopperB. Stop Bolt

The relay panel cover and valve cover panelsshould also be level side-to-side. Slots havebeen provided in the panel hinges to allowadjustment of the panel positions.

MAINTENANCE

365 MM173 (3--90)3-44

BRUSHES

MAIN BRUSH

The main brush is tubular and runs the width of themachine, sweeping debris into the debris hopper. Themain brush should be inspected daily for wear ordamage. Remove any string or wire found tangled onthe main brush, main brush drive hub, or main brushidler hub.

Rotate the main brush end-for-end after every50 hours of operation for maximum brush life andbest sweeping performance.

The main brush pattern should be checked daily. Thepattern should be 2 to 2.5 in (50 to 65 mm) wide withthe main brush in the (Main Brush Down) position.Main brush pattern adjustments are made by turningthe height adjustment knob behind the side shroudnext to the operator’s left leg.

The main brush should be replaced when theremaining bristles measure 1.5 in (40 mm) in length.

TO REPLACE MAIN BRUSH



2. Place the main brush in the (Main BrushFree-Float) position.

3. Open the right side main brush door.

4. Remove the retaining bolt from the brush idlerarm.

B A

03772

MAIN BRUSH IDLER ARM

A. Brush Idler ArmB. Retaining Bolt

5. Pull the brush idler arm off the arm hub.

6. Pull The main brush off the brush drive plug andout of the main brush compartment.

7. Place the new or rotated end-for-end main brushon the floor next to the access door.

8. Slide the main brush into the brushcompartment and onto the drive plug.

9. Slide the main brush idler plug into the mainbrush tube.

10. Slide the brush idler arm onto the arm hub.

11. Thread the brush idler arm retaining bolt throughthe idler arm and into the arm hub.

12. Tighten the brush idler arm retaining bolt.

13. Close the right side main brush door.

14. Check and adjust the main brush pattern asdescribed in TO CHECK AND ADJUST MAINBRUSH PATTERN.

MAINTENANCE

3-45365 MM173 (3--90)

TO CHECK AND ADJUST MAIN BRUSH PATTERN

1. Apply chalk, or some other material that will notblow away easily, to a smooth, level floor.

2. With the side brush in the (Side Brush Up)position, and main brush in the (Main Brush Up)position, position the main brush over thechalked area.

3. Place the main brush position lever in the (MainBrush Down) position for 15 to20 seconds while keeping a foot on the brakesto keep the machine from moving. This willlower and start the main brush rotating.

NOTE: If chalk or other material is not available, allowthe brushes to spin on the floor for two minutes. Donot spin brushes on a coated floor as it may bedamaged.

4. Place the main brush position lever in the (MainBrush Up) position.

5. Drive the machine off the test area.

6. Observe the width of the brush pattern. Theproper brush pattern width is 2 to 2.5 in(50 to 65 mm).

A

00582

NORMAL MAIN BRUSH PATTERN

A. Brush Pattern Width

00601

TAPERED MAIN BRUSH PATTERN

If the main brush pattern is tapered, remove the mainbrush idler arm. Loosen the right side main brushcross shaft bearing mounting bracket bolts and brushleveling bolt jam nut. Adjust the brush leveling boltand pivot the bearing mounting bracket to level thecross shaft. Tighten the right side main brush crossshaft bearing mounting bracket bolts and the brushleveling jam nut. Replace the main brush idler arm.Check the main brush pattern and readjust asnecessary. Then adjust the width of the main brushpattern.

A

B

C

D

03772

MAIN BRUSH LEVELING BOLT

A. Bearing Mounting BracketB. Leveling BoltC. Jam NutD. Idler Arm

MAINTENANCE

365 MM173 (3--90)3-46

To widen the main brush pattern, loosen the mainbrush height adjustment lock knob and turn the heightadjustment knob counterclockwise from the top. Toreduce the width of the main brush pattern, loosen thelock knob and turn the adjustment knob clockwisefrom the top. Tighten the lock knob against theadjustment knob and recheck the main brush pattern.Repeat the procedure until the main brush pattern iswithin specified range.

A

B

C

02150


A. Height Adjustment KnobB. Lock KnobC. Access Door

SIDE BRUSH

The side brush sweeps debris from curbs or guttersinto the path of the main brush. It should be inspecteddaily for wear or damage. Remove any string or wirefound tangled on the side brush or side brush drivehub.

The side brush pattern should be checked daily. Theside brush should just contact the floor when thebrush is in motion. Side brush pattern adjustmentsare made by adjusting the clevis on the side brush liftcable or by connecting the clevis to a different link ofthe side brush lift chain.

A

B

C

D

02158

SIDE BRUSH LIFT CHAIN AND CLEVIS

A. Lift CableB. ClevisC. Lift ChainD. Side Brush

MAINTENANCE

3-47365 MM173 (3--90)

Two other cables control the in-out movement of theside brush. They require no regular adjustment. Whenreplacing the cable which pulls the side brush in asthe hopper raises, adjust the cable so the front of theside brush swings in and measures even with thefront of the machine frame. When replacing the cablewhich pulls the side brush out, adjust the cable so thespring backing plate is 0.5 in (15 mm) inside of thespring tube when the side brush is in the operatingposition and the hopper is in the rolled out andlowered position.

A

B C

02190

SPRING BACKING PLATE

A. Spring TubeB. Backing PlateC. Cable Adjustment Nut

The side brush should be replaced when theremaining brush bristle measures 2.5 in (65 mm) inlength.

TO REPLACE SIDE BRUSH


2. Raise the hopper, engage the hopper supportbar, and lower the hopper onto the support bar.


3. Place the main brush position lever in the (MainBrush Down) position.



5. Remove the plugbutton from the top of the sidebrush bumper.

A

B

C

D

02191

SIDE BRUSH

A. Side BrushB. Side Brush BumperC. PlugbuttonD. Side Brush Retaining Bolt

6. Rotate the side brush by hand until a boltappears through the hole in the side brushbumper. Remove the bolt.

MAINTENANCE

365 MM173 (3--90)3-48

7. Remove the other three side brush retainingbolts in the same manner and remove the sidebrush.

8. Position the new side brush under the sidebrush bumper. Line up one of the four sidebrush mounting holes with the hole in the sidebrush bumper and side brush adapter.

9. Secure the side brush to the side brush adapterwith the bolts removed earlier.

10. Adjust the side brush pattern.

11. Disengage the hopper support bar and lower thehopper.

MAINTENANCE

3-49365 MM173 (3--90)

SKIRTS AND SEALS

HOPPER LIP SKIRTS

The hopper lip skirts are located on the bottom rear ofthe hopper. The lip skirts float over debris, controldust and help deflect the debris into the hopper.

The hopper lip skirts should be inspected for wear ordamage daily.

TO REPLACE HOPPER LIP SKIRTS

1. Empty the machine debris hopper.

2. Stop the machine on a level surface and set themachine parking brake.

3. Raise the hopper, engage the hopper supportbar, and lower the hopper onto the hoppersupport bar.


4. Stop the engine.


5. Remove the skirt retaining strip mounting bolts.

A

BC

03780

HOPPER LIP SKIRTS

A. Hopper Lip SkirtsB. Retaining StripC. Retaining Strip Mounting Bolt

6. Remove the skirt retaining strip and the worn ordamaged skirts.

7. Thread the retaining strip mounting boltsthrough the retaining strip, the skirts, and intothe hopper.

8. Tighten the mounting bolts.


10. Raise the hopper, lower the hopper support bar,and lower the hopper.


BRUSH DOOR SKIRTS

The brush door skirts are located on the bottom ofeach of the two main brush doors. The skirts seal themain brush compartment. The skirts should beinspected for wear or damage, and adjustment daily.

TO REPLACE AND ADJUST BRUSH DOOR SKIRTS

1. Stop the machine on a smooth, level surface.



3. Open the main brush doors.

MAINTENANCE

365 MM173 (3--90)3-50

4. Remove the brush door skirt retaining bolts.

A

B

03778

BRUSH DOOR SKIRT

A. Brush DoorB. Brush Door Skirt

5. Remove the skirt retaining strip and the doorskirt.

6. Position the new door skirt and skirt retainingstrip on the brush door.

7. Thread the skirt retaining bolts through thebrush door, the door skirt, and into the skirtretaining strip.

NOTE: The brush door skirts have slotted holes toallow for a ground clearance adjustment. The doormust be closed for proper adjustment.

8. Slide the brush door skirt up or down so that theskirt clears the floor 0.12 to 0.25 in(5 to 10 mm).

9. Tighten the skirt retaining bolts.

10. Close the brush doors.

REAR SKIRTS

The skirts are located on the bottom rear of the mainbrush compartment. They seal the main brushcompartment. The seals should be inspected for wearor damage, and adjustment daily.

TO REPLACE AND ADJUST REAR SKIRTS

1. Stop the machine on a smooth, level surface.




A

BE

C

D

F

03772

REAR SKIRTS

A. Brush Idler ArmB. Skirt Retaining StripC. Rear Floor SkirtD. Skirt Mounting AngleE. Brush Contact SkirtF. Skirts Mounting Bracket

4. Remove the main brush as described in TOREPLACE MAIN BRUSH.

5. Remove the front skirts mounting bracketretaining bolts. Remove the skirts assembly inone piece.

6. Disassemble the skirts assembly.

7. Reassemble the skirts assembly with a newfloor skirt and brush skirt.

MAINTENANCE

3-51365 MM173 (3--90)

8. Reinstall the skirts assembly in the machine.

9. Slide the rear floor skirt up or down so that theskirt clears the floor 0.12 to 0.25 in(5 to 10 mm).

10. Tighten the retaining bolts.

11. Reinstall the main brush.

HOPPER SIDE SKIRTS

The hopper side skirts are located on the bottom frontsides of the main brush compartment. The skirts sealthe main brush compartment. The skirts should beinspected for wear or damage, and adjustment daily.

TO REPLACE AND ADJUST HOPPER SIDESKIRTS

1. Empty the machine debris hopper.

2. Stop the machine on a level surface and set themachine parking brake.

3. Raise the hopper, engage the hopper supportbar, and lower the hopper onto the hoppersafety support bar.


4. Stop the engine.



6. Remove the hopper side skirt retaining strips.

7. Remove the side skirts.

B

A

03773

HOPPER SIDE SKIRTS

A. Side SkirtB. Retaining Bolt

8. Loosely install new side skirts with the retainingstrips.

9. Slide the skirt up or down so the skirt clears thefloor 0.12 to 0.25 in (5 to 10 mm).

10. Tighten the retaining bolts.


12. Raise the hopper, disengage the support bar,and lower the hopper.


MAINTENANCE

365 MM173 (3--90)3-52

MAIN BRUSH DOOR SEALS

The main brush door seals are located on both mainbrush doors and on corresponding portions of themain frame. They seal the main brush compartment.The seals should be inspected for wear or damageafter every 100 hours of operation.

A

B

03778

MAIN BRUSH DOOR SEALS

A. Main Brush DoorB. Door Seals

B

A

03772

MAIN BRUSH COMPARTMENT SEALS

A. Door SealsB. Main Brush Idler Arm

HOPPER SEALS

The hopper seals are located on the top and sideportions of the machine frame which contacts thehopper. They seal the main brush compartment. Theseals should be inspected for wear or damage afterevery 100 hours of operation.

A

B

03773

HOPPER SEALS

A. Top SealB. Side Seal

HOPPER DOOR SEALS

The hopper door seals are located on the top andside door contact edges of the hopper and the bottomedge of the hopper door. They seal the hopper door.The seals should be checked for wear or damageafter every 100 hours of operation.

A

B

C

D

03722

HOPPER DOOR SEALS

A. Hopper DoorB. Bottom SealC. Hopper Mounted SealsD. Hopper

MAINTENANCE

3-53365 MM173 (3--90)

HOPPER COVER SEAL

The hopper cover seal is located on the bottom of thehopper cover. It seals the hopper filter compartment.The seal should be checked for wear or damage afterevery 100 hours of operation. Check to make sure theseal is evenly compressed. Adjust the hopper coverhinges and latch striker to adjust seal compression.

A

B

02184

HOPPER COVER SEAL

A. Hopper CoverB. Cover Seal

HOPPER VACUUM FAN SEAL

The hopper vacuum fan seal is located on the rear ofthe hopper. It seals the hopper filter compartment tothe vacuum fan intake bracket. The seal should bechecked for wear or damage after every 100 hours ofoperation. Check to make sure that the seal is makinggood contact with the vacuum fan intake bracket. Theseal should be compressed 0.12 in (5 mm) by thecontact.

A

B

03780

HOPPER VACUUM FAN SEAL

A. HopperB. Seal

To adjust seal contact, loosen the vacuum fan intakebracket mounting bolts. Pivot the bracket into thecorrect position and retighten the bolts.

A

B

C

D

E

03721

VACUUM FAN INTAKE BRACKET

A. Intake BracketB. Bracket BoltC. Engine CoverD. Fan Exhaust SealE. Vacuum Fan

MAINTENANCE

365 MM173 (3--90)3-54

BRAKES AND TIRES

SERVICE BRAKES

The service brakes are hydraulically activated by amaster brake cylinder. Check the master brakecylinder fluid level after every 400 hours of operationand add brake fluid as needed. The master brakecylinder is located in front of the operator station. If,due to wear or replacement, the brakes needadjustment, an automotive-type tightening mechanismhas been provided on each brake assembly. Amechanism is located behind a plugbutton on eachside of the inner main frame.

If necessary, adjust the brake clevis on the mastercylinder push rod so that the brake pedal is in ahorizontal position when the cylinder push rod startsto engage the master cylinder piston.

A

B

C

D

02197

BRAKE LINKAGE

A. Brake PedalB. Brake ClevisC. Master Cylinder Push RodD. Master Cylinder

Brakes require bleeding whenever air enters thesystem, lowering the effective braking pressure. Aircan enter when the master cylinder or wheel cylindersare serviced or if the fluid in the reservoir runs dry. Aircan also enter through a leaky brake line or hose.Find the leaking line and replace it before bleeding thesystem.

Whenever handling brake fluid, do not get any on thebrake shoes, drums, or body paint. Brake pads will bepermanently damaged, requiring replacement. Bodypaint can also be damaged unless the area is wipedwith a clean cloth and washed with a soapy solutionimmediately.

TO BLEED THE BRAKES

1. Make sure that the brake fluid reservoir is fulland that the vent in the cap is open.

2. Connect a plastic or rubber tube to the bleedervalve on the left front wheel. Suspend the otherend of the tube in a jar or bottle filled with a fewinches of brake fluid. During the remainingsteps, keep this end submerged at all times andnever let the level in the brake fluid reservoirdrop below one half full.

3. Open the bleeder valve on the left front wheelabout one turn. Have an assistant press thebrake pedal slowly to the floor. As soon as thepedal is all the way down, close the bleedervalve and let the pedal up. Repeat this step asmany times as necessary, until fluid free of airbubbles flows from the tube.

4. Bleed the right front wheel in the same manneras described in the steps above. Keep checkingthe brake fluid reservoir to be sure it doesn’t runout of fluid.

5. When all wheels are bled, discard the brake fluidin the jar or bottle; never reuse such fluid.

6. Fill the brake fluid reservoir with clean fluid.

PARKING BRAKES

The parking brakes are mechanically activated by theparking brake lever and two cables.

The parking brakes should be adjusted whenever themachine rolls after setting the parking brake, when itbecomes very easy to set the parking brake, or afterevery 200 hours of operation. The parking brake maybe routinely tightened by turning the knurled knob onthe end of the parking brake clockwise. If the knobadjustment is inadequate, fully loosen the knob,loosen the brake cable mounting nuts located underthe operator seat, thread the lower nuts closer to theend of the cable, and retighten the top nuts. Be sureto thread each of the nuts out the same number ofturns.

MAINTENANCE

3-55365 MM173 (3--90)

TIRES

The standard front machine tires are pneumatic. Theproper tire air pressure is 50 to 55 psi (345 to 380kPa).

The standard rear machine tire is pneumatic. Theproper tire air pressure is 80 to 85 psi (550 to590 kPa). Check the air pressure of the tires afterevery 100 hours of operation.

Solid tires are available as accessories. No regularmaintenance is required on these tires.

MAINTENANCE

365 MM173 (3--90)3-56

APPENDIX

4-1365 MM173 (3--90)

SECTION 4CONTENTS

PageHARDWARE INFORMATION 4-3. . . . . . . . . . . . . . .

STANDARD BOLT TORQUE CHART 4-3. . . . .METRIC BOLT TORQUE CHART 4-3. . . . . . . .BOLT IDENTIFICATION 4-3. . . . . . . . . . . . . . . . .THREAD SEALANT AND LOCKING

COMPOUNDS 4-3. . . . . . . . . . . . . . . . . . . . . .HYDRAULIC FITTING INFORMATION 4-4. . . . . . .

HYDRAULIC TAPERED PIPE FITTING (NPT)TORQUE CHART 4-4. . . . . . . . . . . . . . . . .

HYDRAULIC TAPERED SEAT FITTING (JIC)TORQUE CHART 4-4. . . . . . . . . . . . . . . . .

HYDRAULIC O--RING FITTING TORQUECHART 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPENDIX

365 MM (3--90)4-2

APPENDIX

4-3365 MM173 (3--90)

HARDWARE INFORMATION

The following charts state standard plated hardwaretightening ranges for normal assembly applications.Decrease the specified torque by 20% when using athread lubricant. Do not substitute lower gradehardware for higher grade hardware. If higher gradehardware than specified is substituted, tighten only tothe specified hardware torque value to avoiddamaging the threads of the part being threaded into,as when threading into speed nuts or weldments.

STANDARD BOLT TORQUE CHART

Thread SAE Grade 5 SAE Grade 8Size Torque ft lb (Nm) Torque ft lb (Nm)

0.25 in 7--10 (9--14) 10--13 (14--38)0.31 in 15--20 (20--27) 20--26 (27--35)0.38 in 27--35 (37--47) 36--47 (49--64)0.44 in 43--56 (58--76) 53--76 (72--103)0.50 in 65--85 (88--115) 89--116 (121--157)0.62 in 130--170 (176--231) 117--265 (159--359)0.75 in 215--280 (291--380) 313--407 (424--552)1.00 in 500--650 (678--881) 757--984 (1026--1334)

NOTE: Decrease torque by 20% when using a threadlubricant.

METRIC BOLT TORQUE CHART

Thread Class 8.8 Class 10.9Size Torque ft lb (Nm) Torque ft lb (Nm)______________________________________________________________M4 2 (3) 3 (4)M5 4 (5) 6 (8)M6 7 (9) 10 (14)M8 18 (24) 25 (34)M10 32 (43) 47 (64)M12 58 (79) 83 (112)M14 94 (127) 133 (180)M16 144 (195) 196 (265)M20 260 (352) 336 (455)M24 470 (637) 664 (900)

NOTE: Decrease torque by 20% when using a threadlubricant.

Exceptions to the above chart:

Main brush drive plug nut -- 30 ft lb (40 Nm) thentighten to next slot.

Front wheel nut -- 10 to 12 ft lb (14 to 16 Nm)while turning wheel, tighten to spec, thenbackoff, retighten by hand till snug, then turn tonext slot.

Rear wheel hub nut -- 200 to 250 ft lb(270 to 340 Nm).

Rear wheel lug nuts -- 85 to 95 ft lb(115 to 130Nm).

BOLT IDENTIFICATION

Identification SpecificationGrade Marking and Grade

SAE--Grade 5

SAE--Grade 8

ISO--Grade 8.8

ISO--Grade 10.901395

THREAD SEALANT AND LOCKING COMPOUNDS

Thread sealants and locking compounds may be usedon this machine. They include the following:

Locktite 515 sealant -- gasket forming material.TENNANTr Part No. 75567,15 oz (440 ml)cartridge.

Locktite 242 blue -- medium strength threadlocking compound. TENNANTr Part No.32676, 0.5 ml tube.

Locktite 271 red -- high strength thread lockingcompound. TENNANTr Part No. 19857, 0.5 mltube.

APPENDIX

365 MM (3--90)4-4

HYDRAULIC FITTING INFORMATION

HYDRAULIC TAPERED PIPE FITTING (NPT)TORQUE CHART

NOTE: Ratings listed are when using teflon threadseal.

Minimum MaximumSize Torque Torque

1/4 NPT 10 ft lb (14 Nm) 30 ft lb (41 Nm)1/2 NPT 25 ft lb (34 Nm) 50 ft lb (68 Nm)3/4 NPT 50 ft lb (68 Nm) 100 ft lb (136 Nm)

HYDRAULIC TAPERED SEAT FITTING (JIC)TORQUE CHART

Tube Thread MaximumO.D. (in) Size Torque

0.25 0.44--20 9 ft lb (12 Nm)0.38 0.56--18 20 ft lb (27 Nm)0.50 0.75--16 30 ft lb (41 Nm)0.62 0.88--14 40 ft lb (54 Nm)0.75 1.12--12 70 ft lb (95 Nm)1.0 1.31--12 90 ft lb (122 Nm)

HYDRAULIC O--RING FITTING TORQUE CHART

Tube Thread Minimum MaximumO.D.(in) Size Torque Torque

0.25 0.44--20 6 ft lb (8 Nm) 9 ft lb (12 Nm)0.38 0.56--18 13 ft lb (18 Nm) 20 ft lb (27 Nm)

*10 ft lb (14 Nm) 12 ft lb (16 Nm)0.50 0.75--16 20 ft lb (27 Nm) 30 ft lb (41 Nm)

*21 ft lb (28 Nm) 24 ft lb (33 Nm)0.62 0.88--14 25 ft lb (34 Nm) 40 ft lb (54 Nm)0.75 1.12--12 45 ft lb (61 Nm) 70 ft lb (95 Nm)1.0 1.31--12 60 ft lb (81 Nm) 90 ft lb (122 Nm)

NOTE: Do not use sealant on o--ring threads.

*Aluminum bodied components

STANDARD PARTS

5-1365 MM173 (3--90)

SECTION 5CONTENTS

PageORDERING REPAIR PARTS 5-3. . . . . . . . . . . . . . .Fig. 1 -- Recommended General

Maintenance Items 5-4. . . . . . . . . . . . .Fig. 2 -- Replacement Brushes 5-5. . . . . . . . . . . . . .Fig. 3 -- Main Frame Group 5-6. . . . . . . . . . . . . . . .Fig. 4 -- Operators Compartment Group 5-8. . . . . .Fig. 5 -- Engine Cover and Side

Panels Group 5-10. . . . . . . . . . . . . . . . .Fig. 6 -- Seat Group 5-12. . . . . . . . . . . . . . . . . . . . . . .Fig. 7 -- Sheaves and Belts Group 5-13. . . . . . . . . . .Fig. 8 -- Engine Fan and Alternator Group,

Distributorless (DIS) 5-14. . . . . . . . . . . . . . .Fig. 9 -- Engine Group 5-16. . . . . . . . . . . . . . . . . . . . .Fig. 10 -- Engine Group, Distributorless (DIS) 5-18.Fig. 11 -- Engine Flywheel and Mounting

Group, Distributorless (DIS) 5-20. . . . .Fig. 12 -- Carburetor and Throttle Group 5-22. . . . . .Fig. 13 -- Carburetor and Throttle Group,

Distributorless (DIS) 5-24. . . . . . . . . . . .Fig. 14 -- Fuel Tank Group 5-26. . . . . . . . . . . . . . . . . .Fig. 15 -- Fuel Tank Group 5-27. . . . . . . . . . . . . . . . . .Fig. 16 -- Fuel Tank Group 5-28. . . . . . . . . . . . . . . . . .Fig. 17 -- Air Cleaner and Hydraulic Filter

Group 5-29. . . . . . . . . . . . . . . . . . . . . . . .Fig. 18 -- Air Cleaner and Hydraulic Filter

Group, Distributorless (DIS) 5-30. . . . .Fig. 19 -- Radiator Group 5-31. . . . . . . . . . . . . . . . . . .Fig. 20 -- Radiator Group, Distributorless (DIS) 5-32Fig. 21 -- Vacuum Fan Group 5-34. . . . . . . . . . . . . . .Fig. 22 -- Hopper Lift Arms Group 5-36. . . . . . . . . . . .Fig. 23 -- Hopper Assembly 5-38. . . . . . . . . . . . . . . . .Fig. 24 -- Hopper Door Group 5-40. . . . . . . . . . . . . . .Fig. 25 -- Muffler Group 5-41. . . . . . . . . . . . . . . . . . . . .Fig. 26 -- Muffler Group, Distributorless (DIS) 5-42. .Fig. 27 -- Side Brush Cables Group 5-43. . . . . . . . . .

PageFig. 28 -- Side Brush Group 5-44. . . . . . . . . . . . . . . . .Fig. 29 -- Main Brush Lift and Drive Group 5-46. . . .Fig. 30 -- Brakes Group 5-48. . . . . . . . . . . . . . . . . . . .Fig. 31 -- Parking Brakes Group 5-50. . . . . . . . . . . . .Fig. 32 -- Front Wheel Group 5-52. . . . . . . . . . . . . . . .Fig. 33 -- Rear Wheel Assembly 5-53. . . . . . . . . . . . .Fig. 34 -- Rear Wheel Support Group 5-54. . . . . . . . .Fig. 35 -- Steering Column Group 5-56. . . . . . . . . . . .Fig. 36 -- Instrument Panel Group 5-58. . . . . . . . . . . .Fig. 37 -- Battery Group 5-59. . . . . . . . . . . . . . . . . . . .Fig. 38 -- Wire Harnesses Group 5-60. . . . . . . . . . . .Fig. 39 -- Wire Harnesses Group 5-62. . . . . . . . . . . .Fig. 40 -- Directional Control Group 5-64. . . . . . . . . .Fig. 41 -- Directional Control Group 5-66. . . . . . . . . .Fig. 42 -- Hydraulic Pumps Group 5-68. . . . . . . . . . . .Fig. 43 -- Hydraulic Pumps Group 5-69. . . . . . . . . . . .Fig. 44 -- Hydraulic Control Valve Group 5-70. . . . . .Fig. 45 -- Hydraulic Reservoir Group 5-72. . . . . . . . .Fig. 46 -- Hydraulic Hoses Group 5-74. . . . . . . . . . . .Fig. 47 -- Hydraulic Hoses Group 5-76. . . . . . . . . . . .Fig. 48 -- Labels Group 5-78. . . . . . . . . . . . . . . . . . . . .

NOTE: SECTION 5, STANDARD MODEL PARTS,lists repair parts for a standard model, gasolinepowered machine. This section also contains partscommon to all models of the machine.

STANDARD PARTS

365 MM173 (3--90)5-2

STANDARD PARTS

5-3365 MM173 (3--90)

ORDERING REPAIR PARTSThe components used in this machine have beencarefully selected for performance and safety. Useonly Tennant Company specified or equivalent parts.

To receive prompt service in filling of your partsorders, please direct all orders for parts with TennantCompany part numbers to the Tennant Company, andall orders for parts with vendor part numbers to thelocal supplier of the respective vendor.

When ordering parts, please furnish all of thefollowing information:

1. Machine model number - shown on the machinedata plate.

SER.NO.

GVW. LBS. KG.

TENNANT COMPANYMINNEAPOLIS, MINNESOTA USA

2. Machine serial number - shown on the machinedata plate.

3. Power source - gasoline, LPG, diesel, electric.

4. Company name.

5. Shipping address.

6. Billing address.

7. Name, first and last - of person ordering parts.

8. Telephone number.

9. Purchase order number.

10. Part number, description, and quantity - of eachitem on the order.

11. Customer ID Number.

Do not order parts by key number or the figurenumber of the illustrated parts. Indented itemsindicate parts of assemblies. Standard hardware isfurnished only when part of a purchased assembly.Please get hardware from a local hardware supplier.

If the old part cannot be identified, send it to us withthe quantity needed specified on the order.

Any claim for loss or damage to a shipment in transitshould be filed promptly against the transportationcompany making the delivery. Shipments will becomplete unless the packing list or order ack-nowledgement indicate items back ordered.

If parts received are suspected to be incorrect ordefective, please write, wire, or phone the TennantCompany representative from whom you ordered thepart. They will give authorization for return and/orhandle replacement shipments when required.

SERIAL NUMBER INFORMATION EXPLANATION

Serial number listings are shown to indicate on whichmachines each part can be used. These listings areexplained by the following examples:

(000000-- ) The part can be used on all machines.

(003342-- ) The part can be used on all machinesbeginning with the serial number listed.

(000000--004320) The part can be used on allmachines up to and including serial number listed.

(004321--005678) The part can be used on allmachines between and including the serial numberslisted.

Where xxxxxx’s are listed in place of a serial number,it indicates a change was made but the exact serialnumber had not been established when the catalogwent to press.

SI UNITS OF MEASURE(INTERNATIONAL SYSTEM)

Metric equivalents have been included, whereapplicable, throughout this parts catalog.

FASTENER STRENGTH IDENTIFICATION

Fasteners required to have high--strength qualitiesequivalent to SAE Grade 8 are identified throughoutthis catalog by the description GR 8. Unless identifiedby this description, all standard fasteners are SAEGrade 5.

(Specifications and design subject to change withoutnotice.)

04239

STANDARD PARTS

365 MM173 (3--90)5-4

04239

Fig. 1 -- Recommended General Maintenance Items

TENNANT MachineKey Part No. Serial Number Description Qty

57519 (000000--006999) Performance Package 400 Hour 101433--1 (000000--006999) Grease, Lubriplate EMB 138245 (000000--006999) Valve, PCV 145770--8 (000000--006999) Spark Plug 454911--24 (000000--006999) Gasket, Valve Cover 1

58120 (000000--006999) Element, Air Filter 158122 (000000--006999) Element, Oil Filter 858476 (000000--006999) Filter, Panel 158506 (000000--006999) Points Set 158507 (000000--006999) Cap, Distributor 1

82697 (000000--006999) Rotor, Overspeed 158509 (000000--006999) Condenser 107328 (000000--006999) Filter, Distributor Cap 107330 (000000--006999) Filter, Distributor 131745 (007000-- ) Performance Package 400 Hour, Gasoline 1

39046 (007000-- ) Spark Plug 407705 (007000-- ) Gasket 158120 (007000-- ) Element, Air Filter 119205 (007000-- ) Element, Engine Oil 882525 (007000-- ) Filter, Fuel 1

32397--1 (007000-- ) Hydraulic Fluid, HP1040, 1 gal 655740 (007000-- ) Element, Hydraulic Fluid Filter 131746 (007000-- ) Performance Package 400 Hour, LPG 139046 (007000-- ) Spark Plug 407705 (007000-- ) Gasket 1

58120 (007000-- ) Element, Air Filter 119205 (007000-- ) Element, Engine Oil 832397--1 (007000-- ) Hydraulic Fluid, HP1040, 1 gal 655740 (007000-- ) Element, Hydraulic Fluid Filter 157518 (000000-- ) Performance Package 800Hour 1

55740 (000000-- ) Element, Hydraulic Fluid 132397--1 (000000-- ) Hydraulic Fluid, Hp1040, 1 gal (3.7 L) 613970 (000000-- ) Maintenance Kit, Brush Door Seals 113177 (000000-- ) Skirt, Side Door, LH 113471 (000000-- ) Skirt, Side Door, LH (Short) 1

13178 (000000-- ) Strip, Retainer, Door Skirt 213468 (000000-- ) Skirt, Side Door, RH 113472 (000000-- ) Skirt, Side Door, RH (Short) 113476 (000000-- ) Retainer, Door Skirt 213296 (000000-- ) Insulation, Brush Door 1

57822 (000000-- ) Seal 157820 (000000-- ) Seal 158543 (000000-- ) Seal 247037 (000000-- ) Adhesive, 5 oz (150 ml) 113293 (000000-- ) Seal, Rubber 2

13294 (000000-- ) Seal, Rubber 213295 (000000-- ) Seal, Rubber 313301 (000000-- ) Seal, Rubber 268198 (000000-- ) Adhesive, 1 oz (150 ml) 113973 (000000-- ) Maintenance Kit, Recirculation Flap 1

13054 (000000-- ) Bracket, Recirculation Flap 113181 (000000--005340) Replacement Kit, Skirt 113056 (000000-- ) Blade, Rear Deflector 1

STANDARD PARTS

5-5365 MM173 (3--90)

TENNANT MachineKey Part No. Serial Number Description Qty

13166 (005341-- ) Skirt, Rear 113165 (005341-- ) Retainer, Skirt 113172 (005341-- ) Strip, Retainer 157858 (000000-- ) Chain, Static 113974 (000000-- ) Maintenance Kit, Hopper Seals 1

13080 (000000-- ) Skirt, Hopper Lip 613081 (000000-- ) Retainer, Hopper Skirt 158485 (000000-- ) Seal, Air Outlet Tube 113083 (000000-- ) Seal, Rubber 147037 (000000-- ) Adhesive, 5 oz (150 ml) 2

13270 (000000-- ) Seal, Rubber 213271 (000000-- ) Seal, Rubber 213301 (000000-- ) Seal, Rubber 213302 (000000-- ) Seal, Rubber 257511 (000000-- ) Seal, Rubber 1

58981 (000000-- ) Seal, Rubber 168198 (000000-- ) Adhesive, 1 oz (30 ml) 1

1

2

03858

Fig. 2 -- Replacement Brushes

TENNANT MachineKey Part No. Serial Number Description Qty.

1 13280 (000000-- ) Main Brush, Proex and Wire 11 13281 (000000-- ) Main Brush, 24 Single Row, Nylon 11 13282 (000000-- ) Main Brush, 8 Double Row, Nylon 11 13283 (000000-- ) Main Brush, Fiber and Wire 12 09600P (000000-- ) Side Brush, Polypropylene 1

2 09600N (000000-- ) Side Brush, Nylon 12 10712K (000000-- ) Side Brush, Flat Wire 1

STANDARD PARTS

365 MM173 (3--90)5-6

4

3

1

2

36

7

26

27

2930

1745

19

46

2021

24

222343

5

24

14

1315

15

28

40

37

18

39

19

20

42

4117

31

2116

32

33

29

44

34

347

8

36

37

189

14

10

1211

35

25

47

46

38

38

38

38

Fig. 3 -- Main Frame Group

STANDARD PARTS

5-7365 MM173 (3--90)

03863

Fig. 3 -- Main Frame Group


1 13747 (000000--006999) Frame, Main 11 31498 (007000-- ) Frame, Main 12 57941 (000000-- ) Taillight Assembly 2

45780 (000000-- ) Bulb 13 87515 (000000-- ) Grommet, Rubber 2

4 58366 (000000-- ) Clamp, Hose 35 57858 (000000-- ) Chain, Static 16 13184 (000000-- ) Stop, Steering, R.H. 17 58898 (000000-- ) Latch, Brush Door 28 34375 (000000-- ) Fitting, Straight 1

9 57979 (000000-- ) Fitting, Straight 110 13114 (000000-- ) Fitting, Tee 111 57978 (000000-- ) Fitting, Tee 112 47753 (000000-- xxxxxx) Fitting, Straight 113 76721 (000000-- ) Grommet, Rubber 1

14 57976 (000000-- ) Fitting, Tee 215 58543 (000000-- ) Seal, Side 216 13472 (000000-- ) Skirt, Side Door, R.H. 117 13476 (000000-- ) Retainer, Strip, 218 58864 (000000-- ) Hinge, Side Door 4

19 13294 (000000-- ) Seal, Rubber 220 13295 (000000-- ) Seal, Rubber 221 13293 (000000-- ) Seal, Rubber 222 13054 (000000-- ) Bracket, Recirculation 123 13181 (000000--005340) Replacement Kit, Rear Skirt 1

23 13165 (005341-- ) Strip, Retainer 124 13056 (000000-- ) Blade, Deflector 125 13181 (000000--005340) Replacement Kit, Rear Skirt 125 13172 (005341-- ) Strip, Retainer 126 58489 (000000-- ) Latch, Hook, Brush Door, R.H. 1

27 13174 (000000-- ) Door, Side, L.H. 128 57820 (000000-- ) Seal 129 13178 (000000-- ) Strip, Skirt Retainer 230 13177 (000000-- ) Skirt, Side Door, L.H. 131 13175 (000000-- ) Door, Side, R.H. 1

32 58844 (000000-- ) Latch, Hook, Brush Door, L.H. 133 57822 (000000-- ) Seal, Brush Door 134 57977 (000000-- ) Fitting, Straight 235 57570 (000000-- ) Molding, Rigid 136 58563 (000000-- ) Pin, Spiral 1

37 58248 (000000-- ) Plugbutton 238 13828 (000000-- ) Dust Shield Replacement Kit 139 13296 (000000-- ) Seal, Brush Door 140 19580 (000000-- ) Screw 241 57588 (000000-- ) Arm Assembly, Safety 1

42 57594 (000000-- ) Label, Safety Arm 143 13181 (000000--005340) Replacement Kit, Rear Skirt 143 13166 (005341-- ) Skirt, Rear 144 13468 (000000-- ) Skirt, Side Door, R.H. 145 13471 (000000-- ) Skirt, Side Door, L.H. 1

46 13301 (000000-- ) Seal 247 13789 (000000-- ) Dust Shield 1

STANDARD PARTS

365 MM173 (3--90)5-8

7

22

32

1533

3

2

1

4

5

6

9

8

31

26

27

17

18

19

20

21

1214

13

12

10

16

11

34

25

2930

28

24

23

25

635

36

Fig. 4 -- Operators Compartment Group

STANDARD PARTS

5-9365 MM173 (3--90)

03852

Fig. 4 -- Operators Compartment Group


1 58724 (000000-- ) Shroud, Rear 12 58759 (000000-- ) Bracket, Rear Shroud 13 57820 (000000-- ) Seal 14 13792 (000000-- ) Cover, Rear Access 15 13131 (000000-- ) Door, Brush Adjustment 1

6 58768 (000000-- ) Fastener 17 58786 (000000-- ) Cover, Battery 18 32270 (000000-- ) Tread, Floor 19 13387 (000000-- ) Panel, Removable 110 14138A (000000-- ) Horn 1

11 13746 (000000--006999) Compartment, Operator 111 31576 (007000-- ) Compartment, Operator 112 58916 (000000-- ) Seal 213 58915 (000000-- ) Seal 114 58819 (000000-- ) Tread, Floor 1

15 13314 (000000--006999) Insulation, Foam 116 13138 (000000-- ) Label, Instrument Panel 117 58911 (000000-- ) Seal 118 58912 (000000-- ) Seal 119 58913 (000000-- ) Seal 1

20 58914 (000000-- ) Seal 121 44847 (000000-- ) Switch 222 69234 (000000-- ) Clamp, Cable 223 31966 (000000-- ) Switch, Rocker, SPDT 124 31964 (000000-- ) Switch, Rocker, DPDT 1

25 57807 (000000-- ) Seal, Rocker Switch 526 57772 (000000-- ) Plate, Cover 127 40678 (000000-- ) Clamp, Cable 228 31963 (000000-- ) Switch, Rocker, DPDT 129 31965 (000000-- ) Switch, Rocker, SPST 1

30 64141--1 (000000-- ) Light Assembly, Panel 131 34816 (000000-- ) Timer, Shaker 132 13279 (000000-- ) Insulation Box Assembly 133 13312 (000000--006999) Seal, Noise 134 69571 (000000-- ) Tread, Floor 1

35 31962 (007000-- ) Switch, Rocker, DPDT 136 31529 (007000-- ) Control Box 1

STANDARD PARTS

365 MM173 (3--90)5-10

24

23

25

26

2722

20

17

30

31

19

1828

32

13

14

12

42

1

9 5

10876

293

11

21

12

1516

21

33

21

3434

Fig. 5 -- Engine Cover and Side Panels Group

STANDARD PARTS

5-11365 MM173 (3--90)

03840

Fig. 5 -- Engine Cover and Side Panels Group


1 58779 (000000-- ) Lintel 12 57564 (000000-- ) Molding, Rigid 13 58776 (000000-- ) Bracket, Support 14 58572 (000000-- ) Cover, Lintel 15 57563 (000000-- ) Molding, Rigid 1

6 13067 (000000-- ) Support, Front 17 58219 (000000-- ) Hinge, Cover, R. H. 18 58222 (000000-- ) Tube, Spacer 19 57889 (000000-- ) Spring, Compression 110 58574 (000000-- ) Angle, Mounting 1

11 13572 (000000-- ) Bracket, Mounting 112 46563 (000000-- ) Bushing, Sleeve 213 58220 (000000--006999) Cover, Engine 113 31581 (007000-- ) Cover, Engine 114 13779 (000000-- ) Label, 365 Logo 1

15 58207 (000000--006999) Duct, Floor 115 31585 (007000-- ) Duct, Floor 116 58218 (000000-- ) Hinge, Cover, L. H. 117 58338 (000000--006999) Angle, Engine Cover 117 31586 (007000-- ) Angle, Engine Cover 1

18 29233 (000000-- ) Bumper, Rubber 119 57905 (000000--006999) Foam, Sound 119 31587 (007000-- ) Foam, Sound 120 58206 (000000-- ) Channel, Mount 121 58494 (000000-- ) Stud, Ball 4

22 31183 (000000-- xxxxxx) Replacement Kit, Gas Spring 222 31182 ( xxxxxx-- ) Spring, Gas 223 58345 (000000-- ) Panel, Left Cover 124 58347 (000000-- ) Hinge, Engine Door 225 58349 (000000--006999) Panel, Engine Door 1

25 13070 (007000-- ) Panel, Engine Door 126 64533 (000000-- ) Latch, Trigger 127 57298 (000000-- ) Bracket, Latch 128 13602 (000000-- ) Seal, Rubber 229 58829 (000000-- ) Insulation, Sound Foam 1

30 04088 (000000-- ) Bracket, Latch Pin 131 58490 (000000-- ) Pin, Latch 132 13598 (000000-- ) Seal, Rubber 133 58828 (000000-- ) Foam, Sound 434 64595 ( xxxxxx-- ) Clip, Safety 4

STANDARD PARTS

365 MM173 (3--90)5-12

12

3

4

5

6

7

8

8

1

02289

Fig. 6 -- Seat Group


1 34252 (000000-- ) Armrest Assembly 12 34251 (000000-- ) Seat 13 68275 (000000-- ) Pouch, Manual 14 58789 (000000-- ) Cover, Seat 15 58780 (000000-- ) Rod

1

6 11476 (000000-- ) Pin, Roll 27 51304--1 (000000-- ) Bearing, Pillowblock 28 58910 (000000-- ) Seal, Seat 3

STANDARD PARTS

5-13365 MM173 (3--90)

AlternatorSheave

Gover-norSheave

1

23

4

5

6

7

8

9

10

11

03832

Fig. 7 -- Sheaves and Belts Group


1 16805 (000000--006999) Fan 12 58098 (000000--006999) Spacer, Fan 13 58045 (000000--006999) Pulley, Water Pump 14 58110 (000000--006999) Housing Assembly, Bearing 15 17759 (000000--006999) V--Belt 1

6 50388 (000000--006999) Screw, Hex, M8 47 54911--10 (000000--006999) Pulley, Water Pump 18 44561 (000000--006999) V--Belt 19 58044 (000000--006999) Pulley, Crankshaft 110 08718 (000000--006999) Tube, Spacer 1

11 13515 (000000--006999) Plate, Governor Mounting 1

STANDARD PARTS

365 MM173 (6--90)5-14

1

2

3

4

5

6

7

8

10

11

12

13

9

14

Fig. 8 -- Engine Fan and Alternator Group, Distributorless (DIS)

STANDARD PARTS

5-15365 MM173 (6--90)

06098

Fig. 8 -- Engine Fan and Alternator Group, Distributorless (DIS)


1 07254 (007000-- ) Strap, Fan Support 12 82537 (007000-- ) Fan 13 07255 (007000-- ) Screw, Socket 34 31534 (007000-- ) Spacer, Fan 15 07189 (007000-- ) V--Belt 1

6 03158 (007000-- ) Pulley, Water Pump 17 54914 (007000--007104) Sheave 18 03233 (007000--007104) Alternator 19 00500--5 (007000--007104) Key, Woodruff 110 31526 (007000-- ) Arm, Alternator 1

11 54959 (007000--007104) Spacer 112 16931 (007000-- ) Screw, Hex, M8 113 39283 (007000-- ) Screw, Hex, M10 214 30458 (007105-- ) Alternator 1

STANDARD PARTS

365 MM173 (3--90)5-16

401516

17

18

14

19

523

24

37

3835

34

33

32

22

26

28

3031

29

39

36 12

1122

21

20

429

8

7

2

13

4

6

25

28

10

13

41

27

15

21

Fig. 9 -- Engine Group

STANDARD PARTS

5-17365 MM173 (3--90)

03850

Fig. 9 -- Engine Group


1 54914 (000000--006999) Sheave 12 58850 (000000--006999) Arm, Alternator 13 03233 (000000--006999) Alternator 14 54959 (000000--006999) Spacer 15 54928 (000000--006999) Bracket 1

6 58592 (000000--006999) Sender, Temperature 17 57548 (000000--006999) Connector, Outlet 18 54911--25 (000000--006999) Gasket, Thermostat 19 58087 (000000--006999) Engine 110 54911--31 (000000--006999) Wire 1

11 54911--11 (000000--006999) Coil 112 54911--30 (000000--006999) Strap, Coil 113 54911--28 (000000--006999) Cover, Fuel Pump 114 82627 (000000--006999) Sender, Oil Pressure 115 17414 (000000--006999) Fitting, Straight 2

16 24929 (000000--006999) Fitting, Tee 117 51805 (000000--006999) Switch, Oil Pressure 118 68106 (000000--006999) Terminal, Tab 319 54911--15 (000000--006999) Resistor 120 58381 (000000--006999) Mount, Engine, L. H. 1

21 51176 (000000--006999) Dampener, Engine 222 51564 (000000--006999) Washer 223 58376 (000000--006999) Mount, Engine, R. H. 124 58377 (000000--006999) Mount, Engine 125 54911--32 (000000--006999) Draincock, Block 1

26 57773 (000000--006999) Wire, Ground 127 54911--7 (000000--006999) Decal, Service 128 54911--16 (000000--006999) Pin, Dowel 229 47933 (000000--006999) Adaptor, Pump 130 00926 (000000--006999) Key, Square 1

31 53531--2 (000000--006999) Coupling, Chain 132 33778 (000000--006999) Chain 133 15280--1 (000000--006999) Bushing134 39330 (000000--006999) Screw, Set 235 53386 (000000--006999) Coupling, Spline 1

36 57549 (000000--006999) Starter 137 54911--5 (000000--006999) Ring, Locating 138 33826 (000000--006999) Housing, Flywheel 139 41361 (000000--006999) Nut, Brass 140 11984 (000000--006999) Fitting, Elbow 1

41 02887 (000000--006999) Gasket, Fuel Pump 142 07120 (000000--006999) Separator, Ignition Wire 1

STANDARD PARTS

365 MM173 (6--90)5-18

1

2

3

4

5

6

7

8

9

10

1112

1314

1516

17

1819

20 21

22

23

24

25

26

23

25

Oil Filter

27

Fig. 10 -- Engine Group, Distributorless (DIS)

STANDARD PARTS

5-19365 MM173 (6--90)

06097

Fig. 10 -- Engine Group, Distributorless (DIS)


1 57773 (007000-- ) Wire Assembly, Ground 12 08165 (007000-- ) Nut, Hex, M8 83 39349 (007000-- ) Washer 84 30316 (007000-- ) Manifold, Exhaust 15 24013 (007000-- ) Fitting, Nipple 1

6 19689 (007000-- ) Housing and Gasket, Thermostat 17 54911--25 (007000-- ) Gasket, Thermostat 18 58592 (007000-- ) Sender, Water Temperature 19 30296 (007000-- ) Engine, Distributorless (DIS) 110 19200 (007000-- ) Fitting, Straight 1

11 16472 (007000-- ) Fitting, Elbow, 45_ 112 40625 (007000-- ) Fitting, Plug 113 17414 (007000-- ) Fitting, Straight 114 26426 (007000-- ) Fitting, Tee 115 51805 (007000-- ) Switch, Oil Pressure 1

16 68106 (007000-- ) Tab, Terminal 317 24976 (007000-- ) Fitting, Elbow, 45_ 118 07175 (007000-- ) Sending Unit, Oil Pressure 119 02887 (007000-- ) Gasket, Fuel Pump 120 16735 (007000-- ) Screw, Hex, M8 2

21 31516 (007000-- ) Bracket, Actuator Mounting 122 31543 (007000-- ) Hose, Heater 123 63810 (007000-- ) Clamp, Worm Drive 224 76589--2 (007000-- ) Hose, Rubber 125 54333 (007000-- ) Clamp, Worm Drive 2

26 30306 (007000-- ) Cap Assembly, Oil Filler 127 30463 (007105-- ) Shield, Exhaust Manifold 1

STANDARD PARTS

365 MM173 (3--90)5-20

1

2

3

4

5 6

7

8910

11

12

13

14

1

1

4

4

5

5

Fig. 11 -- Engine Flywheel and Mounting Group, Distributorless (DIS)

STANDARD PARTS

5-21365 MM173 (6--90)

06095

Fig. 11 -- Engine Flywheel and Mounting Group, Distributorless (DIS)


1 57048 (007000-- ) Washer 32 19106 (007000-- ) Bracket, Rear Engine Mounting, R.H. 13 19100 (007000-- ) Bracket, Rear Engine Mounting, L.H. 14 51176 (007000-- ) Dampner, Engine 35 32493 (007000-- ) Washer 3

6 34877 (007000-- ) Screw, Hex, M10 37 19073 (007000-- ) Housing, Flywheel 18 19531 (007000-- ) Ring, Starter Locating 19 16735 (007000-- ) Screw, Hex, M8 610 19252 (007000-- ) Coupling Assembly, Flywheel 1

11 54911--16 (007000-- ) Pin, Dowel 212 03160 (007000-- ) Starter 113 41361 (007000-- ) Nut, Brass 114 31491 (007000--007104) Mount, Engine Front 114 30434 (007105-- ) Mount, Engine Front 1

STANDARD PARTS

365 MM173 (3--90)5-22

6

5

4

1

8

1526

27

16

17

21 11 2

25

29

14

910

24

18

30

22

32

20

2020

19

23

1213

28

3

36

3334

35

7

31

Fig. 12 -- Carburetor and Throttle Group

STANDARD PARTS

5-23365 MM173 (3--90)

03833

Fig. 12 -- Carburetor and Throttle Group


1 58745 (000000--005773) Knob, Tapered 12 43242 (000000--006999) Swivel 13 58905 (000000--005773) Lever, Choke 14 68058 (000000--006999) Sleeve 15 45261 (000000--006999) Spring, Compression 1

6 51225 (000000--006999) Pin, Clevis 17 08720 (000000--005773) Cable, Choke 18 08719 (000000--006999) Cable, Throttle 19 13525 (000000--006999) Arm, Governor 110 57392 (000000--006999) Spring, Flat 1

11 50332--1 (000000--006999) Ball Joint 112 34898 (000000--006999) Stud, Throttle 113 14601 (000000--006999) Ball Joint 114 40823 (000000--006999) Screw, Shoulder 115 07252 (000000--006999) Nut, Wing 1

16 57934 (000000--006999) Adaptor, Carburetor 117 16738 (000000--006999) Gasket, Air Horn 118 68616 (000000--006999) Valve, Anti--Dieseling 119 55589 (000000--006999) Line Assembly, Fuel 120 46236 (000000--006999) Clamp, Cable 3

21 82674 (000000--005177) Carburetor 121 12044 (005178--006999) Carburetor 1

02738 (000000--006999) Repair Kit, Carburetor 122 54912--8 (000000--006999) Gasket, Carburetor 123 57230 (000000--006999) Bracket, Throttle Cable 1

24 82660 (000000--006999) Governor, Mechanical 125 54745 (000000--006999) Spring 126 07251 (000000--006999) Washer 127 07250 (000000--006999) Stud 128 58846 (000000--005773) Spring, Compression 1

29 13516 (000000--006999) Spacer, Governor 130 11984 (000000--006999) Fitting, Elbow 131 28296 (000000--005773) Pin, Clevis 132 82534 (000000--006999) Shield, Drip 133 47313A (005774--006999) Cable, Choke 1

34 58745 (000000--006999) Knob, Tapered 135 58905 (000000--006999) Lever, Throttle 136 28296 (000000--006999) Pin, Clevis 1

STANDARD PARTS

365 MM173 (6--90)5-24

1

2

3

4 56

78

910

11

12

13

14

15

16

17

18

19

20 21

22

2324

25

26

27

28

21

22

24

Fig. 13 -- Carburetor and Throttle Group, Distributorless (DIS)

STANDARD PARTS

5-25365 MM173 (6--90)

06096

Fig. 13 -- Carburetor and Throttle Group, Distributorless (DIS)


1 07252 (007000-- ) Nut, Wing 12 07251 (007000-- ) Washer, Rubber 13 57934 (007000-- ) Adaptor, Carburetor 14 16738 (007000-- ) Gasket, Carburetor 15 07250 (007000-- ) Stud 1

6 50332--1 (007000-- ) Ball Joint 17 50332--2 (007000-- ) Ball Joint, Stud 18 30451 (007000-- ) Lever, Carburetor 19 30320 (007000-- ) Rod, Throttle Control 110 39311 (007000-- ) Nut, Hex, M8 2

11 15555--1 (007000-- ) Fitting, Elbow 112 69266 (007000-- ) Cable Assembly, Choke 113 49266 (007000-- ) Tie, Cable 114 39780 (007000-- ) Hose, Rubber 115 30305 (007000-- ) Control Assembly, Ignition 1

16 40586 (007000-- ) Fuel Line 117 58846 (007000-- ) Spring, Compression 118 30321 (007000-- ) Carburetor 1

02738 (007000-- ) Repair Kit, Carburetor 119 30325 (007000-- ) Plug, Carburetor 1

20 31542 (007000-- ) Gasket, Carburetor 121 30324 (007000-- ) Stud, M8 222 06532 (007000-- ) Screw, Socket, M6 223 31728 (007000-- ) Plate, Carburetor Mounting 124 30312 (007000-- ) Gasket, Carburetor 2

25 31550 (007000-- ) Shield, Drip 126 07539 (007000-- ) Actuator, Governor 127 30318 (007000-- ) Lever, Governor 128 14601 (007000-- ) Ball Joint 1

STANDARD PARTS

365 MM173 (3--90)5-26

98

7

6

1

2

35

4

1415

10

98

13

11

12

1

10 16

9

17

18

19

20

18

03847

Fig. 14 -- Fuel Tank Group


1 58534 (000000--005830) Strap, Tank 22 58300 (000000--005830) Tank, Fuel 13 48267 (000000--005830) Cap, Tank 14 47473 (000000--005830) Sending Unit, Tank 15 14131 (000000--005830) Gasket 1

6 06507 (000000--005830) Fitting, Elbow 17 11984 (000000--005830) Fitting, Elbow 28 48253 (000000--005830) Fitting, Barbed 29 43844 (000000--005830) Clamp, Worm Drive 410 04107 (000000--005830) Hose 2

11 04106 (000000--005830) Filter, Fuel 112 13251 (000000--005830) Bracket, Fuel Pump 113 54338--7 (000000--005830) Seal, Foam Rubber 114 49263 (000000--005830) Cable Ties 415 13253 (000000--005830) Jumper Wire 1

16 54230 (000000--005830) Pump, Fuel 117 13988 (000000--005228) Cock 117 08873 (005229--005830) Ball Valve 118 22383 (000000--005830) Fitting, Straight 219 46236 (000000--005830) Clamp, Cable 1

20 54231 (000000--005830) Line Assembly, Fuel 1

STANDARD PARTS

5-27365 MM173 (3--90)

9

8

7

6

1

2

3

5

4

109

8

13

11

12

17

05155



1 58534 (005831--006999) Strap, Tank 12 13778 (005831--006999) Tank, Fuel 13 48267 (005831--006999) Cap, Tank 14 47473 (005831--006999) Sending Unit, Tank 15 14131 (005831--006999) Gasket 1

6 11984 (005831--006999) Fitting, Elbow 17 48253 (005831--006999) Fitting, Barbed 28 43844 (005831--006999) Clamp, Worm Drive 49 04107 (005831--006999) Hose 210 04106 (005831--006999) Filter, Fuel 1

11 54230 (005831--006999) Pump, Fuel 112 13238 (005831--006999) Isolator 113 22383 (005831--006999) Fitting, Straight 1

54338--7 (005831--006999) Seal, Foam Rubber 1

STANDARD PARTS

365 MM173 (3--90)5-28

9

8

7

6

1

2

3

5

4

109

8

13

11

12

17

9

06114



1 58534 (007000-- ) Strap, Tank 12 13778 (007000-- ) Tank, Fuel 13 48267 (007000-- ) Cap, Tank 14 47473 (007000-- ) Sending Unit, Tank 15 14131 (007000-- ) Gasket 1

6 11984 (007000-- ) Fitting, Elbow 17 82544 (007000-- ) Fitting, Brass 28 82526 (007000-- ) Hose, Fuelline 29 43844 (007000-- ) Clamp, Worm Drive 410 82525 (007000-- ) Filter, Fuel 1

11 19171 (007000-- ) Pump, Fuel 112 13238 (007000-- ) Isolator 113 40585 (007000-- ) Fitting, Straight 1

STANDARD PARTS

5-29365 MM173 (3--90)

8

17

7

6

4

5

4

15

15

15

16

1210

3

1

11311 2

9

14

03846

Fig. 17 -- Air Cleaner and Hydraulic Filter Group


1 54333 (000000--006999) Clamp, Worm Drive 22 47826 (000000--006999) Hose, Rubber 13 52033 (000000--006999) Indicator, Service 14 58538 (000000--006999) Body, Air Cleaner 15 58120 (000000--006999) Element, Air Cleaner 1

6 51560--3 (000000--006999) Clamp, Mounting 27 57686 (000000--006999) Bracket, Air Cleaner 18 55619 (000000--006999) Filter Assembly, Hydraulic 19 55740 (000000--006999) Element, Hydraulic Filter 110 42260 (000000--006999) Fitting, Straight 1

11 49263 (000000--006999) Tie, Cable 112 58346 (000000--006999) Tube, Air Intake 113 13739 (000000--006999) Tube, Air Outlet 114 82533 (000000--006999) Spud 115 14432 (000000--006999) Clamp, Worm Drive 4

16 58084 (000000--006999) Tube, Inlet 117 16081 (000000--006999) Fitting, Elbow 45_ 1

STANDARD PARTS

365 MM173 (3--90)5-30

1

2

3

4

5

6

7

8

910

11

12

13

14

15

16

17 18

19

20

8

8

8

16

06099

Fig. 18 -- Air Cleaner and Hydraulic Filter Group, Distributorless (DIS)


1 58538 (007000-- ) Air Cleaner 12 58120 (007000-- ) Element, Air Filter 13 02740 (007000-- ) Clamp Assembly 14 02741 (007000-- ) Cup Assembly 15 07562 (007000-- ) Nut, Wing 1

6 51560--3 (007000-- ) Clamp, Mounting 27 82685 (007000-- ) Indicator, Air Filter Service 18 14432 (007000-- ) Clamp, Worm Drive 49 58084 (007000-- ) Hose, Air Intake 110 31511 (007000-- ) Bracket, Air Cleaner Mounting 1

11 78143 (007000-- ) Fitting, Straight 112 42216 (007000-- ) Fitting, Tee 113 55619 (007000-- ) Filter Assembly, Hydraulic 114 55740 (007000-- ) Element, Hydraulic Filter 115 39284 (007000-- ) Screw, Hex, M10 2

16 54333 (007000-- ) Clamp, Worm Drive 217 31515 (007000-- ) Hose, PCV 118 82533 (007000-- ) Spud 119 31486 (007000-- ) Hose, Air Intake 120 46481 (007000-- ) Fitting, Elbow 1

STANDARD PARTS

5-31365 MM173 (3--90)

13

14

6

15

16

12

12

43

17

17

17

1820

2119

12 22

165

7

7

10

89

11

9

03841

Fig. 19 -- Radiator Group


1 03498 (000000--006999) Radiator 12 48655 (000000--006999) Cap, Radiator 13 51305 (000000--006999) Drain Cock 14 13698 (000000--006999) Cooler, Hydraulic 15 58704 (000000--006999) Tab, Mount 2

6 13118 (000000--006999) Bracket, Stabilizer 17 02485 (000000--006999) Nut, Speed 28 04084 (000000--006999) Latch, Rotary 19 82315 (000000--006999) Latch, Quarter Turn 110 03903 (000000--006999) Bracket, Latch Mounting 1

11 82310 (000000--006999) Grille 112 43454 (000000--006999) Washer, Nylon 413 29233 (000000--006999) Bumper, Rubber 214 03912 (000000--006999) Corner, Left Rear 115 13119 (000000--006999) Panel, Rear Engine 1

16 46481 (000000--006999) Fitting, Elbow 217 11531 (000000--006999) Clamp, Worm Drive 418 03909 (000000--006999) Hose, Lower Radiator 119 03908 (000000--006999) Hose, Upper Radiator 120 03907 (000000--006999) Shroud, Fan 1

21 04102 (000000--006999) Guard, Fan 122 57994 (000000--006999) Fitting, Tube, Elbow 1

STANDARD PARTS

365 MM173 (6--90)5-32

1

2

3

45

6

7

8

9

10

11

1213

14 15

16

17

18

19

20

21

2223

24

2

2

2

5

10

11

17

19

22

23

25

Fig. 20 -- Radiator Group, Distributorless (DIS)

STANDARD PARTS

5-33365 MM173 (3--90)

05510

Fig. 20 -- Radiator Group, Distributorless (DIS)


1 31518 (007000-- ) Hose, Radiator 12 11531 (007000-- ) Clamp, Worm Drive 43 30354 (007000-- ) Bar, Support 14 31517 (007000-- ) Hose, Radiator, Upper 15 31541 (007000-- ) Plate, Shroud Support 2

6 31490 (007000-- ) Radiator 17 54911--32 (007000-- ) Cock, Drain 18 82688 (007000-- ) Cap, Radiator 19 54274 (007000-- ) Isolator, Vibration 210 09832 (007000-- ) Washer 2

11 13248 (007000-- ) Washer 212 46481 (007000-- ) Fitting, Elbow 213 19676 (007000-- ) Cable Assembly, Lanyard 114 13698 (007000-- ) Cooler, Hydraulic 115 42260 (007000-- ) Fitting, Straight 1

16 58704 (007000-- ) Tab, Mount 217 02485 (007000-- ) Nut, Speed 218 04084 (007000-- ) Latch, Rotary 119 82315 (007000-- ) Latch, Quarter Turn 120 03903 (007000-- ) Bracket, Latch Mounting 1

21 82310 (007000-- ) Grille 122 43454 (007000-- ) Washer, Nylon 423 29233 (007000-- ) Bumper, Rubber 224 13038 (007000-- ) Panel, Rear 125 30348 (007000-- ) Guard and Label Assembly 1

STANDARD PARTS

365 MM173 (3--90)5-34

8

3

1

31

2711

12

2

45

6

10

14

15

16

28

29

30

28

13

32459

17

19

192018

26 25

24 23

22217

33

Fig. 21 -- Vacuum Fan Group

STANDARD PARTS

5-35365 MM173 (3--90)

03835

Fig. 21 -- Vacuum Fan Group


1 13066 (000000-- ) Bracket, Vacuum Fan 12 23498 (000000-- ) Clamp, Worm Drive 23 57825 (000000-- ) Duct, Flexible 14 34323 (000000-- ) Screw, Nylon Hex 45 03467A (000000-- ) Clip, Housing 4

6 82368 (000000-- ) Inlet Assembly 17 23542 (000000-- ) Seal, Foam Rubber 18 82733 (000000-- ) Gasket, Fire Switch 19 02712 (000000-- ) Thermostat, Sealed 110 82268 (000000-- ) Impeller1

11 13316 (000000-- ) Switch, Roller 112 41136 (000000-- ) Screw, Pan Head 213 13045 (000000--006999) Bracket, Mounting 113 31588 (007000-- ) Bracket, Mounting 114 82386 (000000--006999) Housing, Vacuum Fan 1

14 31713 (007000-- ) Housing, Vacuum Fan 115 13046 (000000-- ) Bracket, Support 116 82661 (000000-- ) Isolator, Vibration 117 57828 (000000-- ) Foam, Acoustic 118 13047 (000000-- ) Duct, Exhaust 1

19 54274 (000000-- ) Isolator, Vibration 420 54275A (000000-- ) Bracket, Motor Mounting 121 77097 (000000-- ) Fitting, Elbow 122 17980 (000000-- ) Fitting, Elbow 123 45482 (000000-- ) Fitting, Tee 1

24 44869 (000000-- ) Fitting, Straight 125 77101 (000000-- ) Motor, Hydraulic 126 44868 (000000-- ) Fitting, Elbow 127 75939 (000000-- ) Nut, Nylon Loc 228 29570 (000000-- ) Washer 4

29 54528 (000000-- ) Bushing, Rubber 230 54527 (000000-- ) Ring, Rubber 231 13601 (000000-- ) Spacer 132 57569 (000000-- ) Molding, Rigid 133 58366 (000000-- ) Clamp, Cable 1

STANDARD PARTS

365 MM173 (3--90)5-36

8

8

5

9

24

26

2125

8

9

2125

8

913

15

31

2

34 33

14

3413

1213

8

3

33

3

1

2

7

21

13

13

12

32178

819

16

27 8

8

18

16

23

913

2216

19

83

816

188

11

89

10

9 8

68

5

89

3

9

486

8

8

89

10

9 8

21

29

28

2830

7

4

9

86

8 617

20

Fig. 22 -- Hopper Lift Arms Group

STANDARD PARTS

5-37365 MM173 (3--90)

03839

Fig. 22 -- Hopper Lift Arms Group


1 13559 (000000-- ) Arms and Torque Tube 12 06418 (000000-- ) Fitting, Grease 23 58676 (000000-- ) Pin 44 58640 (000000-- ) Link, Push 45 58680 (000000-- ) Pin 4

6 32495 (000000-- ) Washer 47 39527 (000000-- ) Nut, Slotted 48 35688 (000000-- ) Bearing, Journal 309 09006 (000000-- ) Washer 1710 58694 (000000-- ) Plate, Rollout 2

11 26395--1 (000000-- ) Clamp, Cable 512 58682 (000000-- ) Pin, Cylinder 213 09005 (000000-- ) Ring, Retaining 614 58696 (000000-- ) Panel, L. H. 115 58695 (000000-- ) Panel, R. H. 1

16 55586 (000000-- ) Fitting, Straight 417 49266 (000000-- ) Tie, Cable 218 16456 (000000-- ) Fitting, Restrictor 219 04464 (000000-- ) Cylinder, Hydraulic 220 58659 (000000-- ) Arm, Upper, L. H. 1

21 58679 (000000-- ) Pin 422 58684 (000000-- ) Pin, Arm Adjustment 123 58644 (000000-- ) Wedge, Arm Adjustment 124 58652 (000000-- ) Arm, Slider, L. H. 125 58647 (000000-- ) Spacer 2

26 58651 (000000-- ) Arm, Slider, R. H. 127 58681 (000000-- ) Pin, Lock 128 58677 (000000-- ) Bearing, Thrust 229 58660 (000000-- ) Bracket, Lock 130 58661 (000000-- ) Spring, Lock 1

31 58658 (000000-- ) Arm, Upper, R. H. 132 58634 (000000-- ) Strip, Unlocking 133 58669 (000000-- ) Screw, Shoulder 234 13173 (000000-- ) Molding, Ridgid 2

STANDARD PARTS

365 MM173 (3--90)5-38

4

34

5133

4352

53

54

55

57

57

56

1

3

2

18

5845

2120

22

2324

20 4748

49

50

5352

604446

4638

36

6

7

8

9

155

24

2534

2437

5554

44

3836

4259 41

39

3536

32

2431 30

299

1113

1617

27

2819

7

10

14

26

40

12

19

61

61

03864

Fig. 23 -- Hopper Assembly


13027 (000000-- ) Hopper Assembly 11 58460 (000000-- ) Cover, Hopper 12 61110 (000000-- ) Nut, Retainer 43 58477 (000000-- ) Panel, Triangle 24 57511 (000000-- ) Seal 1

5 58465 (000000-- ) Bracket, Pin 16 58490 (000000-- ) Pin, Latch 17 36663 (000000-- ) Sleeve, Rubber 2

STANDARD PARTS

5-39365 MM173 (3--90)


8 58476 (000000-- ) Filter Assembly, Panel 19 36665 (000000-- ) Sleeve, Rubber 210 58483 (000000-- ) Bar, Shaker 111 58481 (000000-- ) Clamp, Spring 112 36661 (000000-- ) Pad, Rubber 1

13 55130 (000000-- ) Weight, Eccentric 114 39319 (000000-- ) Screw, Set 215 36666 (000000-- ) Strap, Shaker Motor 116 36658 (000000-- ) Pad, Rubber 117 54121 (000000-- ) Motor, Electric 1

18 40678 (000000-- ) Clamp, Cable 419 58482 (000000-- ) Spring, Shaker 220 58494 (000000-- ) Stud, Ball 421 58485 (000000-- ) Seal, Outlet Tube 122 58484 (000000-- ) Hinge, Hopper Cover 3

23 31183 (000000-- xxxxxx) Replacement Kit, Gas Spring 223 31182 ( xxxxxx-- ) Spring, Gas 224 58424 (000000-- ) Bar, Retainer 625 58981 (000000-- ) Seal, Rubber 126 34868 (000000-- ) Switch, Pressure 1

27 82739 (000000-- ) Fitting, Breather 128 40607 (000000-- ) Fitting, Straight 129 43454 (000000-- ) Washer, Nylon 130 39923 (000000-- ) Fitting, Bulkhead 131 13292 (000000-- ) Hose, Rubber 1

32 58489 (000000-- ) Latch, Hook, R.H. 133 13144 (000000-- ) Plate, Cover 134 13302 (000000-- ) Seal, Rubber 235 13301 (000000-- ) Seal, Rubber 236 10632--3 (000000-- ) Grommet, Rubber 3

37 37031 (000000-- ) Strain Relief 138 58524 (000000-- ) Headlight 239 58496 (000000-- ) Hinge, Hopper Cover 140 56799 (000000-- ) Rivet, Pop 641 13083 (000000-- ) Seal, Rubber 1

42 13082 (000000-- ) Door, Hopper 143 13269 (000000-- ) Plate, Mount, R.H. 144 13270 (000000-- ) Seal, Rubber 245 13335 (000000-- ) Spring, Micro--switch 146 13271 (000000-- ) Seal, Rubber 2

47 32985 (000000-- ) Nut, Hex 448 53963A (000000-- ) Screw, Full Threaded 249 13081 (000000-- ) Strip, Retainer 150 13080 (000000-- ) Skirt, Hopper Lip 651 13132 (000000-- ) Hopper and Label Assembly 1

52 39811 (000000-- ) Screw, Hex 253 32523 (000000-- ) Nut, Jam 254 20567 (000000-- ) Pin, Clevis 255 13244 (000000-- ) Bracket, L 256 13297 (000000-- ) Perma--Filter Assembly 1

57 13236 (000000-- ) Angle, Support 258 13493 (000000-- ) Insulation, Foam 159 13291 (000000-- ) Panel, Deflector 160 13268 (000000-- ) Plate, Mount, L.H. 161 64595 ( xxxxxx-- ) Clip, Safety 4

STANDARD PARTS

365 MM173 (3--90)5-40

1

2

3 45

6

7

8

9

10

5

10

10

03867

Fig. 24 -- Hopper Door Group


1 58488 (000000-- ) Actuator 12 51534 (000000-- ) Pin, Clevis 13 58498 (000000-- ) Pin, Mounting 14 46236 (000000-- ) Clamp, Cable 15 58497 (000000-- ) Pin, Door Pivot 2

6 13211 (000000-- ) Hinge, Hopper Door, L.H 17 13205 (000000-- ) Door, Hopper 18 13212 (000000-- ) Hinge, Hopper Door, R.H. 19 22465 (000000-- ) Spotlight Assembly 1

32827 (000000-- ) Bulb 155272 (000000-- ) Plug, Snap Terminal 1

10 53963A (000000-- ) Screw, Hex 5

STANDARD PARTS

5-41365 MM173 (3--90)

1

2

3

4

5

6

7

8

9

10

11

12

9

513

14

02276

Fig. 25 -- Muffler Group


1 32841 (000000--006999) Stud 22 32840 (000000--006999) Gasket, Exhaust 13 32839 (000000--006999) Flange, Exhaust 14 58932 (000000--005689) Tube, Exhaust 14 13532 (005690--006999) Tube, Exhaust 1

5 24012 (000000--006999) Clamp, Muffler 26 13555 (000000--005689) Muffler 17 47989 (000000--005689) Bracket, L 18 54274 (000000--005689) Isolator, Vibration 19 09832 (000000--005689) Washer 2

10 33330 (005690--005896) Muffler, Replacement Kit 111 82545 (005690--006999) Bracket, Muffler 112 82661 (005690--006999) Isolator 113 33333 (005897--006999) Muffler 114 33329 (005897--006999) Tailpipe 1

STANDARD PARTS

365 MM173 (3--90)5-42

1

2

3

4

5

6

7

8

2

2

2

06115

Fig. 26 -- Muffler Group, Distributorless (DIS)


1 31506 (007000-- ) Tube, Exhaust 12 24012 (007000-- ) Clamp, Muffler 33 33333 (007000-- ) Muffler 14 54274 (007000-- ) Isolator, Vibration 15 09832 (007000-- ) Washer 2

6 13248 (007000-- ) Washer 17 31640 (007000-- ) Bracket, Muffler Hanger 18 33329 (007000-- ) Pipe, Tail 1

STANDARD MODEL PARTS

5-43365 MM173 (3---90)

MainFrame

967

7

7

8

1610

68

6

3

2

1

4

8

1514

22

19

20

21

1718

5

1112

13

03843

Fig. 27 -- Side Brush Cables Group


1 13199 (000000-- ) Knob, Tapered 12 58742 (000000-- ) Lever, Brush 13 06598 (000000-- ) Pin, Clevis 14 13329 (000000-- ) Pivot, Brush 15 58361 (000000-- ) Cable, Lift 1

6 36758 (000000-- ) Screw, Shoulder 37 58279 (000000-- ) Pulley, Cable 58 57910 (000000-- ) Angle, Cable Keeper 39 57760 (000000-- ) Pulley Assembly 110 58236 (000000-- ) Bushing, Sleeve 1

11 58298 (000000-- ) Pin, Pivot 112 58077 (000000-- ) Tube, Pivot 113 58287 (000000-- ) Cable, Swing 114 58237 (000000-- ) Spring, Compression 115 58238 (000000-- ) Spring, Compression 1

16 58228 (000000-- ) Plate, Spring 117 58277 (000000-- ) Cable, Return 118 57908 (000000-- ) Block, Cable Guide 119 58244 (000000-- ) Clevis 120 04743 (000000-- ) Pin, Clevis 1

21 46307 (000000-- ) Chain, Link 122 13290 (000000-- ) Angle, Cable Keeper 2


365 MM173 (3---90)5-44

15

2819

SideBrush

18

26

2722

22

23

23

2524

1

2

3

2

45

9

6 10

11

12

13

14

16

7

30

30

20

29

8

17

21

13

Fig. 28 -- Side Brush Group


5-45365 MM173 (3---90)

03849

Fig. 28 -- Side Brush Group


58035 (000000-- ) Shaft Assembly 11 57835 (000000-- ) Pivot Assembly, Vertical 12 57936 (000000-- ) Bearing, Journal 23 09718 (000000-- ) Fitting, Grease 14 58359 (000000-- ) Ring, Retaining 1

5 58281 (000000-- ) Spacer, Spring 16 57852 (000000-- ) Spring, Compression 17 57860 (000000-- ) Pivot Assembly 18 57936 (000000-- ) Bearing, Journal 19 57870 (000000-- ) Shaft, Vertical Pivot 1

10 58246 (000000-- ) Pin, Spiral 111 23546 (000000-- ) Pin, Roll 112 57866 (000000-- ) Pivot Assembly, Horizontal 113 58293 (000000-- ) Bearing, Journal 214 58290 (000000-- ) Pin, Pivot 1

15 23999--3 (000000-- ) Pin, Roll 216 57892 (000000-- ) Guard, Brush 117 47178 (000000-- ) Plugbutton 118 57896 (000000-- ) Bumper, Side Brush 119 13249 (000000-- ) Mount, Brush 1

20 20050 (000000-- ) Pin, Roll 121 13105 (000000--005923) Motor, Hydraulic, Replaced by 28808 121 28808 (005924-- ) Motor, Hydraulic 122 57984 (000000-- ) Fitting, Straight 223 39210 (000000-- ) Fitting, Elbow 224 34329 (000000-- ) Sleeve, Hose 1

25 49266 (000000-- ) Tie, Cable 326 56980 (000000-- ) Clamp, Retaining 127 69743 (000000-- ) Bushing, Split 228 39396 (000000-- ) Screw, Lag 429 58275 (000000-- ) Link 2

30 69582 (000000-- ) Pin, Clevis 2


365 MM173 (3---90)5-46

2728

3129

2624

25

13

30

1415

1416

12

6

11

9

8

6

4

3

2

1

7

5

14

17

15

13301823

22

19

2223

21

20

6

10

Fig. 29 -- Main Brush Lift and Drive Group


5-47365 MM173 (3---90)

03834

Fig. 29 -- Main Brush Lift and Drive Group


1 13199 (000000-- ) Knob, Tapered 12 58743 (000000-- ) Lever, Main Brush 13 06598 (000000-- ) Pin, Clevis 14 13327 (000000-- ) Pivot, Main Brush 15 67290 (000000-- ) Pin, Clevis 1

6 06598 (000000-- ) Pin, Clevis 37 57743 (000000-- ) Clevis, Adjustable, R.H. 18 57742 (000000-- ) Knob, Adjusting 19 57741 (000000-- ) Rod, Brush Lift 110 57744 (000000-- ) Clevis, Adjustable, L.H. 1

11 58767 (000000-- ) Bar, Lift 112 13170 (000000-- ) Shaft, Brush 113 51317 (000000-- ) Pin, Roll 214 51449 (000000-- ) Flange, Bearing 415 51448 (000000-- ) Bearing and Collar 2

16 57849 (000000-- ) Plate, Bracket 117 58254 (000000-- ) Bracket 1

13179 (000000-- ) Arm Assembly, Brush, R.H. 118 13157 (000000-- ) Arm, Brush R.H. 119 13151 (000000-- ) Shaft, Idler Brush 120 00927 (000000-- ) Key, Square 1

21 87631 (000000-- ) Plug, Brush Drive 122 13534 (000000-- ) Bearing, Ball 223 40727 (000000-- ) Ring, Retaining 2

13180 (000000-- ) Arm Assembly, Brush, L.H. 124 13156 (000000-- ) Arm, Brush, L.H. 125 87631 (000000-- ) Plug, Brush Drive 1

26 13106 (000000--005943) Motor, Hydraulic, Replaced by 27800 126 27800 (005944-- ) Motor, Hydraulic 127 44869 (000000-- ) Fitting, Straight 228 55586 (000000-- ) Fitting, Straight 129 13202 (000000-- ) Clamp 130 51059 (000000-- ) Hub, Brush 231 82830 (000000-- ) Sleeve 1


365 MM173 (3---90)5-48

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2018

17

16

5

5

4

Fig. 30 -- Brakes Group


5-49365 MM173 (3---90)

03836

Fig. 30 -- Brakes Group


1 51109 (000000-- ) Pad 12 58399 (000000-- ) Pedal, Brake 13 58848 (000000-- ) Pin, Clevis 14 58244 (000000-- ) Clevis, Female 35 14331 (000000-- ) Pin, Clevis 3

‘

6 05416 (000000-- ) Stud 17 58529 (000000-- ) Bellcrank 18 57904 (000000-- ) Pin, Clevis 19 58337 (000000-- ) Rod, Push 110 SK2136 (000000-- ) Replacement Kit, Brake Cylinder 1

SK2137 (000000-- ) Repair Kit, Cylinder 111 13959 (000000-- ) Switch 112 11984 (000000-- ) Fitting, Elbow 113 51483 (000000-- ) Fitting, Tee 114 58678 (000000-- ) Tube Assembly 1

15 76058 (000000-- ) Tube Assembly 116 09092--1 (000000-- ) Clamp, Hold--Down 217 57856 (000000-- ) Spindle 218 34292 (000000-- ) Screw, Hex 819 57782 (000000-- ) Brake Assembly, L.H. 1

58329 (000000-- ) Replacement Kit, Brake Cylinder 158330 (000000-- ) Replacement Kit, Brake Shoe 1

20 57781 (000000-- ) Brake Assembly, R.H. 158329 (000000-- ) Replacement Kit, Brake Cylinder 158330 (000000-- ) Replacement Kit, Brake Shoe 1


365 MM173 (3---90)5-50

1

2

3

4

5

6

7

8

9

10

11

1213

14

15

1514

8

8

10

Right HandBrake Assembly

Left HandBrakeAssembly

Fig. 31 -- Parking Brakes Group


5-51365 MM173 (3---90)

03838

Fig. 31 -- Parking Brakes Group


1 58772 (000000-- ) Cover, Lever 12 43896 (000000-- ) Screw, Pan, Thread Forming 33 51545 (000000-- ) Lever, Brake 14 51562 (000000-- ) Sleeve 25 57791 (000000-- ) Plate, Spacer 1

6 58279 (000000-- ) Pulley, Cable 17 58535 (000000-- ) Cable 18 69582 (000000-- ) Pin, Clevis 59 58311 (000000-- ) Clevis 210 26395--1 (000000-- ) Clamp, Cable 2

11 58319 (000000-- ) Plate, Transfer 112 58320 (000000-- ) Cable Assembly, L. H. 113 58321 (000000-- ) Cable Assembly, R. H. 114 65129 (000000-- ) Clamp, Cable 215 39302 (000000-- ) Screw, Socket 4


365 MM173 (3---90)5-52

2

5

6

7

8

9

10

1112

13

14

25

3

1

4

02317

Fig. 32 -- Front Wheel Group


1 57565 (000000-- ) Seal, Grease 22 68297 (000000-- ) Bearing, Cone 43 58328 (000000-- ) Drum, Brake 24 57275 (000000-- ) Stud, Wheel 55 24989 (000000-- ) Cup, Bearing 2

6 31705 (000000-- ) Washer 27 41112 (000000-- ) Nut, Slotted 28 58331 (000000-- ) Tire and Rim Assembly 29 57277 (000000-- ) Tire 110 57278 (000000-- ) Rim 1

11 75365 (000000-- ) Valve, Tubeless Tire 112 45786 (000000-- ) Cap, Valve Stem 113 24339 (000000-- ) Nut, Wheel 1014 57567 (000000-- ) Cap, Hub 2


5-53365 MM173 (3---90)

6

3

1

5

4

1

2

3

01532

Fig. 33 -- Rear Wheel Assembly


51357 (000000-- ) Tire and Rim Assembly 11 52775 (000000-- ) Rim Assembly 12 51355 (000000-- ) Stud, Wheel 6

52510 (000000-- ) Tire Assembly 13 51362 (000000-- ) Tire 1

4 51360 (000000-- ) Flap 15 51361 (000000-- ) Tube 16 45786 (000000-- ) Cap, Valve Stem 1


365 MM173 (3---90)5-54

25

1

24

15

3

6 810

5

26

7

26

26

4

4

13

23

2

6

22 18

20

21

19

17

16

14

14

13

12

11

9

Fig. 34 -- Rear Wheel Support Group


5-55365 MM173 (3---90)

03837

Fig. 34 -- Rear Wheel Support Group


1 04430 (000000-- ) Cylinder, Hydraulic 12 16081 (000000-- ) Fitting, Elbow, 45_ 13 08731 (000000-- ) Spacer 14 32987 (000000-- ) Nut, Nylon Hex 25 77097 (000000-- ) Fitting, Elbow 1

6 55586 (000000-- ) Fitting, Straight 27 08733 (000000-- ) Plate, Mounting 18 58842 (000000-- ) Plate, Hose Support 19 34330 (000000-- ) Sleeve, Hydraulic 110 49263 (000000-- ) Tie, Cable 3

11 14242 (000000-- ) Nut, Slotted Hex 112 47719 (000000-- ) Washer 113 49225 (000000-- ) Bearing, Cup and Cone 114 57577 (000000-- ) Support, Rear Wheel 115 57561 (000000-- ) Screw, Hex 1

16 09718 (000000-- ) Fitting, Grease 117 57925 (000000-- ) Pin, Wheel Support 118 19583 (000000-- ) Screw, Socket 419 58368 (000000-- ) Hub and Stud Assembly 120 32126 (000000-- ) Stud, Wheel 6

21 24339 (000000-- ) Nut, Wheel 622 48663 (000000-- ) Motor, Hydraulic 123 42260 (000000-- ) Fitting, Straight 124 39900 (000000-- ) Screw, Hex 125 39350 (000000-- ) Washer 2

26 32486 (000000-- ) Washer 6


365 MM173 (3---90)5-56

1

2

3

45

6

78

9

10

11

12

13

14

15

16

17

18

19

20

2122

2324

2526

27

28

18

17

Fig. 35 -- Steering Column Group


5-57365 MM173 (3---90)

03855

Fig. 35 -- Steering Column Group


1 47010--7 (000000-- ) Cover, Horn 12 47010--6 (000000-- ) Button, Horn 13 47010--2 (000000-- ) Cup, Contact 14 47010--3 (000000-- ) Spring, Horn 15 47010--1 (000000-- ) Cap, Contact 1

6 47010--4 (000000-- ) Screw, Horn 37 14700--4 (000000-- ) Plate Assembly, Base 18 58737 (000000-- ) Wheel, Steering 19 57676 (000000-- ) Nut, Steering Wheel 110 52388 (000000-- ) Steering Column Assembly 1

11 58748 (000000-- ) U--Bolt 112 57982 (000000-- ) Valve, Hydraulic Steering 113 55685 (000000-- ) Fitting, Straight 214 34330 (000000-- ) Sleeve, Hose 115 49263 (000000-- ) Tie, Cable 3

16 58924 (000000-- ) Column, Steering 117 58796 (000000-- ) Bracket, Mount 218 58775 (000000-- ) Bracket, Reinforcement 219 06777 (000000-- ) Clamp, Cable 120 58810 (000000-- ) Bar, Spring Guide 1

21 63852 (000000-- ) Spring, Compression 122 58762 (000000-- ) Spring, Torsion 123 58797 (000000-- ) Bracket, Notched 124 58793 (000000-- ) Lever, Tilt 125 51813 (000000-- ) Pin, Clevis 1

26 58807 (000000-- ) Bar, Spring Support 127 13199 (000000-- ) Knob, Tapered 128 56690 (000000-- ) Fitting, Straight 2


365 MM173 (3---90)5-58

17

15

1614

14 13 12

7

10

2

986

43

5

11

1

18

02265

Fig. 36 -- Instrument Panel Group


1 58769 (000000--005923) Panel, Instrument 11 13879 (005924-- ) Panel, Instrument 12 09925 (000000-- ) Label, Instrument Panel 13 34810 (000000-- ) Meter, Hour 14 82626 (000000--006999) Gauge, Oil Pressure 1

4 07056 (007000-- ) Gauge, Oil Pressure 15 58591 (000000-- ) Gauge, Water Temperature 16 34813 (000000-- ) Gauge, Fuel 17 48252 (000000-- ) Terminal, Tab 28 55557 (000000-- ) Gauge, Voltage 1

9 57807 (000000-- ) Seal, Switch 110 31965 (000000-- ) Switch, Rocker 111 55271 (000000-- ) Light, Instrument 412 55258 (000000--005923) Switch, Ignition 112 87536 (005924-- ) Switch, Ignition 1

13 62530--1 (000000--005923) Key Set, Ignition 113 87866 (005924-- ) Key Set, Ignition 114 09385 (000000-- ) Clamp, Cable 215 57803 (000000-- ) Breaker, Circuit 616 43949 (000000-- ) Screw, Pan 2

17 57751 (000000-- ) Boot, Breaker 618 19768 (005924-- ) Plate, Ignition 1


5-59365 MM173 (3---90)

1

23

4

03853

Fig. 37 -- Battery Group


1 57769 (000000-- ) Strap, Rubber 12 57778 (000000-- ) Cable, Positive Battery 13 57345 (000000-- ) Cable, Negative Battery 14 10137 (000000-- ) Battery, 475 ccA 1


365 MM173 (3---90)5-60

1 2

3

3

Fig. 38 -- Wire Harnesses Group


5-61365 MM173 (3---90)

4

03860



1 13864 (000000--005569) Replacement Kit, Main Wire Harness 12 13259 (000000--005569) Wire Harness, Hopper 13 02513 (000000--005923) Wire Harness, Instrument Panel 14 57804 (000000-- ) Relay, Electrical 4


365 MM173 (3--90)5-62

1

2

3

5



5-63365 MM173 (3--90)

4

06117



1 13818 (005924-- ) Wire Harness, Main 12 13807 (005570-- ) Wire Harness, Hopper 13 13818 (005924-- ) Wire Harness, Instrument Panel 14 57804 (000000-- ) Relay, Electrical 45 31528 (007000-- ) Wire Harness, Engine 1


365 MM173 (3--90)5-64

2017 22

21

14

11

78

6

135

12

43

30

29

3132

28

34

2726

24

259

1035

33

16

15

12

23PropellingPump

1921

19

18

7

Fig. 40 -- Directional Control Group


5-65365 MM173 (3--90)

03842



1 58820 (000000--006999) Tread, Pedal 12 58819 (000000--006999) Tread, Pedal 13 13097 (000000--006999) Pedal, Directional Control 14 58824 (000000--006999) Sleeve 15 58517 (000000--006999) Rod, Directional Control 1

6 00912 (000000--006999) Key, Square 17 39328 (000000--006999) Screw, Set 28 03549 (000000--006999) Coupling, Shaft, R.H. 19 14595--1 (000000--006999) Clevis, Adjustable 110 14605 (000000--006999) Pin, Clevis 1

11 57875 (000000--006999) Coupling, Shaft 112 54274 (000000--006999) Isolator 113 10827 (000000--006999) Screw, Socket 414 57873 (000000--006999) Bracket, Engine Mounting 115 57874 (000000--006999) Bracket, Spring 1

16 49681 (000000--006999) Plate, Spring 417 04081 (000000--006999) Coupling Assembly, L.H. 118 31249 (000000--006999) Screw, Shoulder 119 19580 (000000--006999) Screw, Socket 220 03556 (000000--006999) Nut, Self--Locking 2

21 09787 (000000--006999) Washer, Clipped 222 45181 (000000--006999) Nut, Self--Locking 123 13248 (000000--006999) Washer, Special 124 13378 (000000--006999) Cable, Speed Limiter 125 46328 (000000--006999) Roller, Cable 1

26 13361 (000000--006999) Bracket, Cable Retainer 127 13360 (000000--006999) Shaft, Mounting 128 13392 (000000--006999) Bracket, Speed Limiter 129 13540 (000000--006999) Spring 130 29087 (000000--006999) Screw, Shoulder 1

31 13413 (000000--006999) Spacer 132 59632 (000000--006999) Sleeve 133 13362 (000000--006999) Cam, Speed Limiter 134 13554 (000000--006999) Plate 135 13513 (000000--006999) Nut, Nylon Lock 1


365 MM173 (3--90)5-66

1

2

3

4

5

67

8

9

10

11

12

13 14

15 16

1718

19

20

2122

23

24 25

2627

28

29 30

31

3233

34

35

36

37

10

17

19

22

13



5-67365 MM173 (3--90)

06100



1 13097 (007000-- ) Pedal, Directional Control 12 58819 (007000-- ) Tread, Pedal 13 58820 (007000-- ) Tread, Pedal 14 58824 (007000-- ) Sleeve 15 58517 (007000-- ) Rod, Directional Control 1

6 00912 (007000-- ) Key, Square 17 34096 (007000-- ) Bearing, Flange 18 39328 (007000-- ) Screw, Set 29 31539 (007000-- ) Plate, Directional Control 110 51531 (007000-- ) Ball Joint 2

11 59054 (007000-- ) Rod, Threaded 112 19074 (007000-- ) Plate, PUmp Control 113 64991 (007000-- ) Sleeve 414 57875 (007000-- ) Coupling, Shaft 115 02702 (007000-- ) Washer, Retainer 2

16 15280--3 (007000-- ) Bushing 117 39330 (007000-- ) Screw, Set 218 02701 (007000-- ) Flange, Coupling 119 49681 (007000-- ) Plate, Spring 420 16736 (007000-- ) Screw, Nylon Hex 1

21 19071 (007000-- ) Bracket, Spring Mounting 122 56855 (007000-- ) Bumper, Rubber 223 14595--1 (007000-- ) Clevis, Adjustable 124 14605 (007000-- ) Pin, Clevis 125 46328 (007000-- ) Roller, Cable 1

26 13361 (007000-- ) Bracket, Cable Retainer 127 13360 (007000-- ) Shaft, Mounting 128 13554 (007000-- ) Plate 129 13392 (007000-- ) Bracket, Speed Limiter 130 29087 (007000-- ) Screw, Shoulder 1

31 13540 (007000-- ) Spring 132 13413 (007000-- ) Spacer 133 59632 (007000-- ) Sleeve 134 20160 (007000-- ) Pin, Roll 135 13362 (007000-- ) Cam, Speed Limiter 1

36 13513 (007000-- ) Nut, Nylon Lock 137 13378 (007000-- ) Cable, Speed Limiter 1


365 MM173 (3--90)5-68

1

23

4

5

6

7

8

9

10

11

12 13

14

15

16

17

18

19

20

21

18

03844

Fig. 42 -- Hydraulic Pumps Group


1 02634 (000000--006999) Pump, Hydraulic 12 13101 (000000--006999) Pump, Hydraulic 13 65145--1 (000000--006999) O--Ring 14 58395 (000000--006999) O--Ring 25 82767 (000000--006999) Valve, Neutral Valve 1

6 82764 (000000--006999) Screw, Socket 37 57993 (000000--006999) Fitting, Straight 18 07934 (000000--006999) Fitting, Elbow, 45_ 19 41016 (000000--006999) Clamp, Cable 110 67811 (000000--006999) Fitting, Straight 1

11 56692 (000000--006999) Fitting, Straight 112 55686 (000000--006999) Fitting, Straight 113 42260 (000000--006999) Fitting, Straight 114 57994 (000000--006999) Fitting, Special Elbow 115 62390 (000000--006999) Fitting, Straight 1

16 62389 (000000--006999) Fitting, Tee 117 39210 (000000--006999) Fitting, Elbow 118 57979 (000000--006999) Fitting, Straight 219 35033 (000000--006999) Fitting, Elbow 120 57992 (000000--006999) Fitting, Cross 1

21 47524 (000000--006999) Fitting, Straight 1


5-69365 MM173 (3--90)

1

2

3

4

56

7

8

9 10

11

12

13

14

15

16

17

8

15

7

06112

Fig. 43 -- Hydraulic Pumps Group


1 02704 (007000-- ) Pump, Hydraulic 12 13101 (007000-- ) Pump, Hydraulic 13 65145--1 (007000-- ) O--Ring 14 58395 (007000-- ) O--Ring 25 82767 (007000-- ) Valve, Neutral Valve 1

6 82764 (007000-- ) Screw, Socket 37 42260 (007000-- ) Fitting, Straight 28 35033 (007000-- ) Fitting, Elbow 29 41016 (007000-- ) Clamp, Cable 110 67811 (007000-- ) Fitting, Straight 1

11 56692 (007000-- ) Fitting, Straight 112 55686 (007000-- ) Fitting, Straight 113 44869 (007000-- ) Fitting, Straight 114 39210 (007000-- ) Fitting, Elbow 115 57979 (007000-- ) Fitting, Straight 2

16 57992 (007000-- ) Fitting, Cross 117 47524 (007000-- ) Fitting, Straight 1


365 MM173 (3--90)5-70

11 7

7

13

13

12

12

1

10

10

9 85

46

4

3

2

Fig. 44 -- Hydraulic Control Valve Group


5-71365 MM173 (3--90)

03862

Fig. 44 -- Hydraulic Control Valve Group


1 13104 (000000-- ) Valve, Hydraulic Solenoid 12 42260 (000000-- ) Fitting, Straight 13 56820 (000000-- ) Fitting, Elbow 14 44869 (000000-- ) Fitting, Straight 35 44868 (000000-- ) Fitting, Elbow 1

6 17980 (000000-- ) Fitting, Elbow 17 29570 (000000-- ) Washer 28 55586 (000000-- ) Fitting, Straight 19 39210 (000000-- ) Fitting, Elbow 110 77097 (000000-- ) Fitting, Elbow 4

11 13061 (000000-- ) Plate, Valve Mounting 112 54528 (000000-- ) Bushing, Rubber 213 54527 (000000-- ) Ring, Rubber 2


365 MM173 (3--90)5-72

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

18

17

5

3

Fig. 45 -- Hydraulic Reservoir Group


5-73365 MM173 (3--90)

03845

Fig. 45 -- Hydraulic Reservoir Group


1 57942 (000000--005752) Breather--Filler 12 58941 (000000--005752) Bracket, Mounting 13 54333 (000000--005752) Clamp, Worm Drive 24 57957 (000000--005752) Hose, Hydraulic 15 22297 (000000--005752) Clamp, Worm Drive 2

6 57956 (000000--005752) Hose, Hydraulic 17 49263 (000000--005752) Tie, Cable 28 40362 (000000-- ) Fitting, Plug 19 56692 (000000-- ) Fitting, Straight 110 58934 (000000-- ) Mount, Reservoir 1

11 58933 (000000-- ) Mount, Reservoir 112 57776 (000000--005752) Reservoir Assembly 113 31613 (000000-- ) Strainer, Suction 114 58858 (000000-- ) Fitting, Straight 115 49287 (000000--005752) Clamp, Cable 1

16 06750 (000000-- ) Fitting, Straight 117 13788 (005753-- ) Reservoir Assembly 118 13791 (005753-- ) Breather--Filler 1


365 MM173 (3--90)5-74

SideBrushMotor

Lift andDumpCylinder

MainControlValve


MainBrushMotor

HydraulicFilter

HydraulicCooler

Pump

VacuumFan

SteeringCylinder

PropelMotor

HydraulicReservoir

PowerSteering

19

20

22

23

15

1

2

9 10

11

25

24

216

13

2

1

518

17

16

7

8

14

4

3

12

26

27

Fig. 46 -- Hydraulic Hoses Group


5-75365 MM173 (3--90)

03861



1 57946 (000000--006999) Hose, Hydraulic 22 57575 (000000--006999) Hose, Hydraulic 23 57967 (000000--006999) Hose, Hydraulic 24 49957--1 (000000--006999) Hose, Hydraulic 25 34380 (000000--006999) Hose, Hydraulic 2

6 57945 (000000--006999) Hose, Hydraulic 17 57153 (000000--006999) Hose, Hydraulic 18 13108 (000000--006999) Hose, Hydraulic 19 31563 (000000--006999) Hose, Hydraulic 110 57968 (000000--006999) Hose, Hydraulic 1




26 57955 (000000--006999) Hose, Hydraulic 127 57953 (000000--006999) Hose, Hydraulic 1


365 MM173 (3--90)5-76

SideBrushMotor


MainControlValve


MainBrushMotor

HydraulicFilter

HydraulicCooler

Pump

VacuumFan

SteeringCylinder

PropelMotor

HydraulicReservoir

PowerSteering

19

20

22

23

15

1

2

910

11

25

24

21

6

13

2

1

518

17

16

7

8

14

4

3

12

26

27



5-77365 MM173 (3--90)

00000



1 57946 (007000-- ) Hose, Hydraulic 22 57575 (007000-- ) Hose, Hydraulic 23 57967 (007000-- ) Hose, Hydraulic 24 49957--1 (007000-- ) Hose, Hydraulic 25 34380 (007000-- ) Hose, Hydraulic 2

6 57945 (007000-- ) Hose, Hydraulic 17 57153 (007000-- ) Hose, Hydraulic 18 82822 (007000-- ) Hose, Hydraulic 19 31563 (007000-- ) Hose, Hydraulic 110 57968 (007000-- ) Hose, Hydraulic 1




26 57955 (007000-- ) Hose, Hydraulic 127 57953 (007000-- ) Hose, Hydraulic 1


365 MM173 (3--90)5-78

1

1

1

1

4

2

1

12

2

3

1

1

03866

Fig. 48 -- Labels Group


13130 (000000--006999) Label Kit, Complete 131560 (007000-- ) Label Kit, Complete 1

1 13756 (000000-- ) Label Kit, Information and Hazard 12 13751 (000000--006999) Label Kit, Striping 1

31718 (007000-- ) Label, Numberals 365 13 13195 (000000--006999) Label Kit, Operational 13 31561 (007000-- ) Label Kit, Operational 14 13139 (000000--006999) Label, Maintenance Chart 1

LPG PARTS

6-1365 MM173 (3--90)

SECTION 6CONTENTS

PageORDERING REPAIR PARTS 6-3. . . . . . . . . . . . . . .Fig. 1 -- Carburetor and Fuel Tank

Group, LPG 6-4. . . . . . . . . . . . . . . . . . .Fig. 2 --- Engine Group, Distributorless

(DIS), LPG 6-6. . . . . . . . . . . . . . . . . . . .

NOTE: SECTION 6, LPG PARTS, lists repair partsunique to an LPG powered machine.

LPG PARTS

365 MM173 (3--90)6-2

LPG PARTS

6-3365 MM173 (3--90)





SER.NO.

GVW. LBS. KG.




4. Company name.


6. Billing address.






















LPG PARTS

365 MM173 (3--90)6-4

28

29

2928

28

2829

32

31

39

37

30

32

34

3541

40

29

33

36

1621

2223

26

24201918

17

13 12

4

14

11

9 86

62

2

1

2

5

3

10

7

15

25

2738

InstrumentPanel

OperatorCompartment

Fig. 1 -- Carburetor and Fuel Tank Group, LPG

NOTE: To identify parts shown but not listed, see SECTION 5, STANDARD MODEL PARTS.

LPG PARTS

6-5365 MM173 (3--90)

03865

Fig. 1 -- Carburetor and Fuel Tank Group, LPG


1 55633 (000000-- ) Bumper, LPG 12 20536--1 (000000-- ) Washer 43 29499 (000000-- ) Spring, Tension 14 58582 (000000-- ) Bumper, LPG 15 11893 (000000-- ) Eyebolt 1

6 46231 (000000-- ) Sleeve 27 58581 (000000-- ) Bracket, Locator Stud 18 53400--1 (000000-- ) Latch 19 53400--4 (000000-- ) Lug 110 57297 (000000-- ) Strap, Hinge 1

11 58590 (000000-- ) Strap, Retainer 112 58589 (000000-- ) Strap, Mounting 113 58588 (000000-- ) Cradle, Tank 114 24928 (000000-- ) Tank, LPG, 33 lb 114 24928--1 (000000-- ) Tank, LPG, 33 lb, with Filler Gauge 1

15 26496 (000000-- ) Coupling, LPG 116 22308 (000000-- ) Hose, LPG 117 49266 (000000-- ) Tie, Cable 218 27048 (000000-- ) Fitting, Elbow 119 56976A (000000-- ) Fitting, Tee 1

20 24047 (000000-- ) Valve, Pressure Relief 121 11442--1 (000000-- ) Fitting, Elbow 122 33555 (000000-- ) Fuel Filter Lock 1

SK1444 (000000-- ) Repair Kit, Fuel Filter Lock 123 58194 (000000-- ) Bracket, Mounting 1

24 68106 (000000-- ) Terminal, Tab 125 47192 (000000-- ) Hose, LPG 126 26395--1 (000000-- ) Clamp, Cable 127 54930 (000000--006999) Vaporizer, LPG 1

55998 (000000--006999) Repair Kit, Vaporizer 1

28 51839 (000000--006999) Fitting, Elbow 429 54333 (000000--006999) Clamp, Worm Drive 430 13048 (000000--006999) Hose, Rubber 131 82505 (000000--006999) Hose 132 46611 (000000--006999) Fitting, Elbow 2

33 08727 (000000--006999) Bracket, Mounting 134 57544 (000000-- ) Label, Choke Cover 135 82691 (000000--006999) Carburetor, LPG 136 13049 (000000--006999) Hose 137 76589--2 (000000--006999) Hose 1

38 43242 (000000--006999) Swivel 139 82684 (000000--006999) Fitting, Straight, Barbed 140 47178--6 (000000-- ) Plugbutton 141 27048 (000000--006999) Fitting, Elbow 1

LPG PARTS

365 MM173 (6--90)6-6

1

2

3

4

5

6

7

8

910

11

12

13

1415 16

17

18

19

20

21

2223

24

20

18

1817

18

4

Fig. 2 -- Engine Group, Distributorless (DIS), LPG

LPG PARTS

6-7365 MM173 (6--90)

06110

Fig. 2 -- Engine Group, Distributorless (DIS), LPG


1 30322 (007000-- ) Carburetor, LPG 155975 (007000-- ) Repair Kit, Carburetor 1

2 31542 (007000-- ) Gasket, Carburetor 13 30324 (007000-- ) Stud, M8 24 06532 (007000-- ) Screw, Socket, M6 2

5 31728 (007000-- ) Plate, Carburetor Mounting 16 30312 (007000-- ) Gasket, Carburetor 17 39311 (007000-- ) Nut, Hex, M8 28 30451 (007000-- ) Lever, Carburetor 19 50332--2 (007000-- ) Ball Joint, Stud 1

10 50332--1 (007000-- ) Ball Joint 111 30320 (007000-- ) Rod, Throttle Control 112 07602 (007000-- ) Fitting, Elbow 113 07597 (007000-- ) Hose, LPG 114 30326 (007000-- ) Bracket, Vaporizer 1

15 07598 (007000-- ) Fitting, Elbow 116 54930 (007000-- ) Vaporizer, LPG 1

55998 (007000-- ) Repair Kit, Vaporizer 117 51839 (007000-- ) Fitting, Elbow 218 63810 (007000-- ) Clamp, Worm Drive 4

19 11442--1 (007000-- ) Fitting, Elbow 120 31543 (007000-- ) Hose, Heater (Cut in 2 pieces) 121 49263 (007000-- ) Tie, Cable 222 14601 (007000-- ) Ball Joint 123 30318 (007000-- ) Lever, Governor 1

24 07539 (007000-- ) Actuator, Governor 1

LPG PARTS

365 MM173 (3--90)6-8

ACCESSORIES

7-1365 MM173 (3--90)

SECTION 7CONTENTS

PageORDERING REPAIR PARTS 7-3. . . . . . . . . . . . . . .Fig. 1 -- Revolving Light Kit, Shroud 7-4. . . . . . . . .Fig. 2 -- Revolving Light Kit, Overhead

Guard 7-5. . . . . . . . . . . . . . . . . . . . . . . .Fig. 3 -- Revolving Light Kit, Cab 7-6. . . . . . . . . . . .Fig. 4 -- Flashing Light Kit, Shroud 7-7. . . . . . . . . .Fig. 5 -- Flashing Light Kit, Overhead

Guard 7-8. . . . . . . . . . . . . . . . . . . . . . . .Fig. 6 -- Flashing Light Kit, Cab 7-9. . . . . . . . . . . . .Fig. 7 -- Overhead Guard Kit 7-10. . . . . . . . . . . . . . .Fig. 8 -- Air Filter Safety Kit 7-11. . . . . . . . . . . . . . . . .Fig. 9 -- Fire Extinguisher Kit 7-12. . . . . . . . . . . . . . .Fig. 10 -- Protectoseal Fuel Tank Cap Kit 7-12. . . . .Fig. 11 -- Solid Tire Kit 7-13. . . . . . . . . . . . . . . . . . . . . .Fig. 12 -- Cab Kit 7-14. . . . . . . . . . . . . . . . . . . . . . . . . .Fig. 13 -- Cab Door Assembly 7-16. . . . . . . . . . . . . . .Fig. 14 -- Cab Pressurizer Group 7-18. . . . . . . . . . . .Fig. 15 -- Wire Harnesses Group, Cab 7-19. . . . . . . .Fig. 16 -- Cab Heater Group 7-20. . . . . . . . . . . . . . . .Fig. 17 -- Cab Heater Electrical Group 7-22. . . . . . . .Fig. 18 -- Cab Heater Group 7-24. . . . . . . . . . . . . . . .Fig. 19 -- Cab Heater Electrical Group 7-26. . . . . . . .Fig. 20 -- Vacuum Wand Kit 7-28. . . . . . . . . . . . . . . . .Fig. 21 -- Heavy Duty Bumper Group 7-30. . . . . . . . .Fig. 22 -- Urethane Tire Kit 7-31. . . . . . . . . . . . . . . . . .

NOTE: SECTION 7, ACCESSORIES, lists repairparts included as part of the available accessories.

ACCESSORIES

365 MM173 (3--90)7-2

ACCESSORIES

7-3365 MM173 (3--90)





SER.NO.

GVW. LBS. KG.

TENNANT COM-PANYMINNEAPOLIS, MINNESOTA USA



4. Company name.


6. Billing address.






















ACCESSORIES

365 MM173 (3--90)7-4

1

2

34

5

6

7

8

9

10

11

12

Shroud

OperatorCompartment

02308

Fig. 1 -- Revolving Light Kit, Shroud


58041 (000000-- ) Light Kit, Revolving Red, Shroud 11 55297 (000000-- ) Light Assembly, Revolving Red 1

44681 (000000-- ) Lens, Red 145779 (000000-- ) Bulb 1

2 47178--16 (000000-- ) Plugbutton 1

3 29192 (000000-- ) Terminal, Ring 14 48258 (000000-- ) Sleeve, Vinyl 15 10632--12 (000000-- ) Grommet 16 58065 (000000-- ) Bracket 17 46236 (000000-- ) Clamp, Cable 2

8 22794 (000000-- ) Terminal, Ring 19 50470 (000000-- ) Terminal, Female 110 57807 (000000-- ) Seal, Switch 111 31965 (000000-- ) Switch, Rocker 112 57740 (000000-- ) Label, Hazard Light 1

55290 (000000-- ) Light Assembly, Revolving Blue 144681--2 (000000-- ) Lens, Blue 155291 (000000-- ) Light Assembly, Revolving Amber 144681--1 (000000-- ) Lens, Amber 1


ACCESSORIES

7-5365 MM173 (3--90)

1

23

4

5

6

7

8

9

OverheadGuard

02304

Fig. 2 -- Revolving Light Kit, Overhead Guard


58133 (000000-- ) Light Kit, Revolving Red, Overhead Guard 11 55297 (000000-- ) Light Assembly, Revolving Red 1

44681 (000000-- ) Lens, Red 145779 (000000-- ) Bulb 1

2 47178--16 (000000-- ) Plugbutton 1

3 55272 (000000-- ) Plug, Terminal 14 10632--12 (000000-- ) Grommet 15 58068 (000000-- ) Wire Harness, Overhead Guard 16 46236 (000000-- ) Clamp, Cable 37 57807 (000000-- ) Seal, Switch 1

8 31965 (000000-- ) Switch, Rocker 19 57740 (000000-- ) Label, Hazard Light 1



ACCESSORIES

365 MM173 (3--90)7-6

1

2

3

4

5

6

7

Cab

02306

Fig. 3 -- Revolving Light Kit, Cab


58139 (000000-- ) Light Kit, Revolving Red, Cab 11 55297 (000000-- ) Light Assembly, Revolving Red 1

44681 (000000-- ) Lens, Red 145779 (000000-- ) Bulb 1

2 47178--16 (000000-- ) Plugbutton 1

3 10632--20 (000000-- ) Grommet 14 55272 (000000-- ) Plug, Terminal 15 57807 (000000-- ) Seal, Switch 16 31965 (000000-- ) Switch, Rocker 17 57740 (000000-- ) Label, Hazard Light 1



ACCESSORIES

7-7365 MM173 (3--90)

1

2

3

4

5

67

8

9

10

11

Shroud

02307

Fig. 4 -- Flashing Light Kit, Shroud


58038 (000000-- ) Light Kit, Flashing Red, Shroud 11 58510 (000000-- ) Light Assembly, Flashing Red 1

45779 (000000-- ) Bulb 158518 (000000-- ) Lens, Red 1

2 29192 (000000-- ) Terminal, Ring 1

3 48258 (000000-- ) Sleeve, Vinyl 14 10632--12 (000000-- ) Grommet 15 58065 (000000-- ) Bracket 16 46236 (000000-- ) Clamp, Cable 37 22794 (000000-- ) Terminal, Ring 1

8 50470 (000000-- ) Terminal, Female 19 57807 (000000-- ) Seal, Switch 110 31965 (000000-- ) Switch, Rocker 111 57740 (000000-- ) Label, Hazard Light 1

58511 (000000-- ) Light Assembly, Blue 1

58519 (000000-- ) Lens, Blue 158512 (000000-- ) Light Assembly, Amber 158520 (000000-- ) Lens, Amber 1


ACCESSORIES

365 MM173 (3--90)7-8

1

2

34

56

7

8

OverheadGuard

02303

Fig. 5 -- Flashing Light Kit, Overhead Guard


58130 (000000-- ) Light Kit, Flashing Red, Overhead Guard 11 58510 (000000-- ) Light Assembly, Flashing Red 1

45779 (000000-- ) Bulb 158518 (000000-- ) Lens, Red 1

2 55272 (000000-- ) Plug, Terminal 1

3 10632--12 (000000-- ) Grommet 14 58068 (000000-- ) Wire Harness 15 46236 (000000-- ) Clamp, Cable 36 57807 (000000-- ) Seal, Switch 17 31965 (000000-- ) Switch, Rocker 1

8 57740 (000000-- ) Label, Hazard Light 158511 (000000-- ) Light Assembly, Flashing Blue 158519 (000000-- ) Lens, Blue 158512 (000000-- ) Light Assembly, Flashing Amber 158520 (000000-- ) Lens, Amber 1


ACCESSORIES

7-9365 MM173 (3--90)

1

2

3

4

5

6

Cab

02305

Fig. 6 -- Flashing Light Kit, Cab


58136 (000000-- ) Light Kit, Flashing Red, Cab 11 58510 (000000-- ) Light Assembly, Flashing Red 1

45779 (000000-- ) Bulb 158518 (000000-- ) Lens, Red 1

2 10632--20 (000000-- ) Grommet 1

3 55272 (000000-- ) Plug, Terminal 14 57807 (000000-- ) Seal, Switch 15 31965 (000000-- ) Switch, Rocker 16 57740 (000000-- ) Label, Hazard Light 1

58511 (000000-- ) Light Assembly, Flashing Blue 1

58519 (000000-- ) Lens, Blue 158512 (000000-- ) Light Assembly, Flashing Amber 158520 (000000-- ) Lens, Amber 1


ACCESSORIES

365 MM173 (3--90)7-10

1

02291

Fig. 7 -- Overhead Guard Kit


1 58773 (000000-- ) Overhead Guard Kit 1

ACCESSORIES

7-11365 MM173 (3--90)

1

2

02274

Fig. 8 -- Air Filter Safety Kit


07565 (000000-- ) Element Kit, Air, Safety 11 58121 (000000-- ) Element, Safety 12 07562 (000000-- ) Wingnut 1

ACCESSORIES

365 MM173 (3--90)7-12

1

EngineCover

02300

Fig. 9 -- Fire Extinguisher Kit


46938 (000000-- ) Extinguisher Kit, Fire 11 25312 (000000-- ) Extinguisher, Fire 1

FuelTank

1

02295

Fig. 10 -- Protectoseal Fuel Tank Cap Kit


1 02506--6 (000000-- ) Cap, Fuel Tank, Protectoseal 1


ACCESSORIES

7-13365 MM173 (3--90)

1

2

3

4

1

02302

Fig. 11 -- Solid Tire Kit


58113 (000000-- ) Solid Tire Kit 151705 (000000-- ) Tire and Wheel Assembly, Solid 1

1 52775 (000000-- ) Rim Kit, Tire 12 51355 (000000-- ) Stud, Wheel 63 51711 (000000-- ) Tire, Solid 1

4 58296 (000000-- ) Tire and Wheel Assembly, Solid 2

ACCESSORIES

365 MM173 (3--90)7-14

13

1521

20

14

44

8

338

35

6

34

37

32

30

31

2928

42 22

16

23

2426

34

36

2

39

1

5

4

9

10

11

12

40

41

17

19

18

27

33

25

7

43

Fig. 12 -- Cab Kit

ACCESSORIES

7-15365 MM173 (3--90)

03941

Fig. 12 -- Cab Kit

NOTE: Cab Kit, TENNANT Part Number 13036, includes Fig. 12, Fig. 13, Fig. 14, and Fig. 15.


1 57670 (000000-- ) Cab 12 58910 (000000-- ) Seal, Seat 23 58951 (000000-- ) Light, Dome 14 51416 (000000-- ) Terminal, Male 25 51406 (000000-- ) Connector 1

6 57652 (000000-- ) Weather Strip 17 68106 (000000-- ) Terminal 18 10632--14 (000000-- ) Grommet 39 57625 (000000-- ) Cover, Access 110 58967 (000000-- ) Gasket, Access 1

11 58210 (000000-- ) Weather Strip 112 58209 (000000-- ) Glass, Rear 113 58968 (000000-- ) Cover, Hose 114 57654 (000000-- ) Channel, Flexible 115 57526 (000000-- ) Spacer, Rubber 1

16 57653 (000000-- ) Weather Strip 117 57643 (000000-- ) Channel, Rigid 118 15066 (000000-- ) Pull and Lock Set 119 58974 (000000-- ) Pad, Rubber 220 04134 (000000-- ) Glass, Stationary 1

21 57634 (000000-- ) Glass, L. H. 122 58964 (000000-- ) Seal 123 57648 (000000-- ) Seal 124 57877 (000000-- ) Motor, Wiper 125 57651 (000000-- ) Weather Strip 1

26 57636 (000000-- ) Glass, Front 127 58898 (000000-- ) Latch 128 57534 (000000-- ) Seal 129 57664 (000000-- ) Angle 130 57677 (000000-- ) Lintel, Cab 1

31 57919 (000000-- ) Mount, Wiper 132 57918 (000000-- ) Arm, Wiper 133 57970 (000000-- ) Blade, Wiper 134 37083--1 (000000-- ) Catch 235 57674 (000000-- ) Housing, Filter Mount 1

36 58958 (000000-- ) Filter, Air 137 57639 (000000-- ) Glass, Front, R.H. 1

13041 (000000-- ) Replacement Kit, Cab Insulation 138 04148 (000000-- ) Foam, Accoustic 139 13585 (000000-- ) Insulation, Control Panel 1

40 13586 (000000-- ) Insulation, Corner 141 13596 (000000-- ) Insulation, Lower Rear Panel 142 13594 (000000-- ) Insulation, Dashboard 143 13590 (000000-- ) Insulation, Upper Rear Panel 144 13597 (000000-- ) Insulation, Left Panel 1

ACCESSORIES

365 MM173 (3--90)7-16

1

2

34

5

6

7

8

9

10

11

12

1314

15

16

17

18

19

21 22

23

24

25

20

2321

Fig. 13 -- Cab Door Assembly

ACCESSORIES

7-17365 MM173 (3--90)

02279

Fig. 13 -- Cab Door Assembly



57649 (000000-- ) Door Assembly, Cab 11 57640 (000000-- ) Weather Strip 12 04134 (000000-- ) Glass, Stationary 13 57643 (000000-- ) Channel, Rigid 14 57642 (000000-- ) Spacer, Rubber 1

5 57641 (000000-- ) Channel, Flex 16 58974 (000000-- ) Tape, Setting 27 15066 (000000-- ) Pull and Lock Set 18 57633 (000000-- ) Glass, Sliding 19 57662 (000000-- ) Door, Cab 1

10 57637 (000000-- ) Armrest, Door 111 57647 (000000-- ) Handle, Door 112 58973 (000000-- ) Cover, Door Latch 113 13164 (000000-- ) Spring, Tension 114 58489 (000000-- ) Latch, Hook 1

15 57646 (000000-- ) Cam 116 57631 (000000-- ) Glass, Stationary 117 57644 (000000-- ) Weather Strip 118 57678 (000000-- ) Plate, Seal Mount 119 58957 (000000-- ) Seal 120 13757 (000000-- ) Bracket, Latch Stop 1

21 57667 (000000-- ) Hinge 222 58962 (000000-- ) Shim, 0.05” (1 mm) 123 58963 (000000-- ) Shim, 0.12” (3 mm) 224 58966 (000000-- ) Sleeve, Door Stop 125 57598 (000000-- ) Pin, Clevis 1

ACCESSORIES

365 MM173 (3--90)7-18

1

2

3

4

5

6

7

8

9

10 10

9

7

4

02294

Fig. 14 -- Cab Pressurizer Group



1 57535 (000000-- ) Blower Assembly 12 57608 (000000-- ) Housing, Pressurizer 13 57604 (000000-- ) Bracket, Mount 14 26395--1 (000000-- ) Clamp, Cable 25 63837 (000000-- ) Switch 1

6 63814 (000000-- ) Knob 17 31965 (000000-- ) Switch, Rocker 28 58950 (000000-- ) Decal, Cab 19 57537 (000000-- ) Fastener 810 57536 (000000-- ) Louver 2

ACCESSORIES

7-19365 MM173 (3--90)

1

2

03942

Fig. 15 -- Wire Harnesses Group, Cab



1 58955 (000000-- ) Wire Harness, Cab 12 58956 (000000-- ) Wire Harness, Cab Wiper 1

ACCESSORIES

365 MM173 (3--90)7-20

GovernorSheave

2

2

2

2

2

2

2

2

12

CrankshaftPulley

8

292

10

112

19

4 2

2

19

219

15

2

22

4

20

62120

4

7

4

4

4

4

5

5

3

1

14

14

132

16

13

14

Engine

LPGVaporizer

WaterPump

OperatorCompartment

Water PumpPulley

18 17

Fig. 16 -- Cab Heater Group

NOTE: To identify parts shown but not listed, see SECTION 5, STANDARD MODEL PARTS or SECTION 6, LPGPARTS.

ACCESSORIES

7-21365 MM173 (3--90)

03258


NOTE: Cab Heater Kit, TENNANT Part Number 57903, includes Fig. 16 and Fig. 17.


1 57528 (000000--006999) Core, Heater 12 63810 (000000--006999) Clamp, Worm Drive 163 57533 (000000--006999) Hose, Heater 24 20343 (000000--006999) Fitting, Straight 75 32418 (000000--006999) Fitting, Elbow 2

6 57531 (000000--006999) Hose, Heater 17 13122 (000000--006999) Hose, Heater 18 44961 (000000--006999) Tie, Cable 39 57872 (000000--006999) Fitting, Y 110 57871 (000000--006999) Hose, Heater 1

11 58948 (000000--006999) Fitting, Tee 112 57532 (000000--006999) Hose, Heater 213 04118 (000000--006999) Reducer, Hose 214 11399 (000000--006999) Clamp, Worm Drive 415 04123 (000000--006999) Hose, Adaptor 1

16 04125 (000000--006999) Hose, Radiator 117 04104 (000000--006999) Pump, Solution 1

SK2498 (000000--006999) Replacement Kit, Brushes 103711 (000000--006999) Replacement Kit, Pump Head 133308 (000000--006999) Replacement Kit, Pump Body 1

51406 (000000--006999) Connector, Body 151416 (000000--006999) Terminal, Male 2

18 04121 (000000--006999) Bracket, Heater Pump 119 51839 (000000--006999) Fitting, Elbow 220 47167 (000000--006999) Fitting, Straight 2

21 13127 (000000--006999) Valve, Solenoid 122 13124 (000000--006999) Hose 1

ACCESSORIES

365 MM173 (3--90)7-22

5

6

03454

Fig. 17 -- Cab Heater Electrical Group


ACCESSORIES

7-23365 MM173 (3--90)

1

2

3

4

InstrumentPanel

PressurizerHousing

BlowerAssembly

03257




1 57751 (000000-- ) Boot, Circuit Breaker 12 57803 (000000-- ) Breaker, Circuit 13 04133 (000000-- ) Label, Heater 14 63266 (000000-- ) Switch 15 57804 (000000-- ) Relay 1

6 13334 (000000-- ) Wire Harness, Heater 1

ACCESSORIES

365 MM173 (3--90)7-24

Engine

LPGVaporizer

12

5

6

7

83

3

3

3

3

3

3

3

3

3

3

3

3

3

33

3

4

4

4

6

910

10

1011

11 12

13

14

1516 17

18

19

20

21

22

11

12

13

14

14

20

20

21

14

Engine


NOTE: To identify parts shown but not listed, see SECTION 5, STANDARD MODEL PARTS or SECTION 6, LPGPARTS.

ACCESSORIES

7-25365 MM173 (3--90)

06106




1 57528 (007000-- ) Core, Heater 12 17409 (007000-- ) Cable Assembly 13 63810 (007000-- ) Clamp, Worm Drive 164 13124 (007000-- ) Hose, Heater 15 31754 (007000-- ) Bracket 1

6 47701 (007000-- ) Fitting, Elbow 28 31507 (007000-- ) Valve 19 47167 (007000-- ) Fitting, Straight 110 20343 (007000-- ) Fitting, Straight 511 57872 (007000-- ) Fitting, Y 3

12 57532 (007000-- ) Hose, Heater 213 32418 (007000-- ) Fitting, Elbow 214 31543 (007000-- ) Hose, Heater 215 57531 (007000-- ) Hose, Heater 216 04121 (007000-- ) Bracket, Heater Pump 1

17 04104 (007000-- ) Pump, Solution 1SK2498 (007000-- ) Replacement Kit, Brushes 103711 (007000-- ) Replacement Kit, Pump Head 133308 (007000-- ) Replacement Kit, Pump Body 151406 (007000-- ) Connector, Body 1

51416 (007000-- ) Terminal, Male 218 04123 (007000-- ) Hose, Adaptor 119 04125 (007000-- ) Hose, Radiator 120 11399 (007000-- ) Clamp, Worm Drive 421 04118 (007000-- ) Reducer, Hose 2

22 43242 (007000-- ) Swivel 1

ACCESSORIES

365 MM173 (3--90)7-26

5

6

7

03454



ACCESSORIES

7-27365 MM173 (3--90)

1

2

3

4

InstrumentPanel

PressurizerHousing

BlowerAssembly

06116




1 57751 (007000-- ) Boot, Circuit Breaker 12 57803 (007000-- ) Breaker, Circuit 13 04133 (007000-- ) Label, Heater 14 63266 (007000-- ) Switch 15 57804 (007000-- ) Relay 1

6 13334 (007000-- ) Wire Harness, Heater 17 06570 (007000-- ) Wire Assembly 1

27184 (007000-- ) Connector, 3-Way 1

ACCESSORIES

365 MM173 (3--90)7-28

14

15

8

814

2

2

9

9

17

17

3

1

15

518

18

6

6

4

4

7

7

3

10

12

16

13

11

3

HopperHood

Hopper

Fig. 20 -- Vacuum Wand Kit


ACCESSORIES

7-29365 MM173 (3--90)

03943

Fig. 20 -- Vacuum Wand Kit


13028 (000000-- ) Wand Kit, Vacuum 11 13226 (000000-- ) Door, Vac Wand 22 13309 (000000-- ) Seal, Rubber 23 13229 (000000-- ) Seal, Rubber 44 13308 (000000-- ) Seal, Rubber 2

5 13306 (000000-- ) Seal, Rubber 26 13203 (000000-- ) Handle, Door 27 01047 (000000-- ) Retainer 28 13090 (000000-- ) Bracket, Vacuum Wand Door, Upper 29 51372 (000000-- ) Spring 2

10 13233 (000000-- ) Plate, Access 111 54009 (000000-- ) Hose and Cuff Assembly 112 54012 (000000-- ) Wand 113 67004 (000000-- ) Clip, Finger Grip 614 13302 (000000-- ) Seal, Rubber 215 13301 (000000-- ) Seal, Rubber 216 13743 (000000-- ) O--ring 217 13228 (000000-- ) Bracket, Vacuum Wand Door, Lower 218 13689 (000000-- ) Insulation, Wand Handle 2

ACCESSORIES

365 MM173 (3--90)7-30

1

2

3

02153

Fig. 21 -- Heavy Duty Bumper Group


1 13734 (000000--006999) Frame, Heavy Duty Bumper 11 31500 (007000-- ) Frame, Heavy Duty Bumper 12 57703 (000000-- ) Guard, Side Brush 13 57710 (000000-- ) Bumper, Front, L. H. 1


ACCESSORIES

7-31365 MM173 (3--90)

1

03452

Fig. 22 -- Urethane Tire Kit


1 16869 (000000-- ) Urethane Tire Kit 1

ACCESSORIES

365 MM173 (3--90)7-32

HYDRAULIC COMPONENTS

8-1365 MM173 (3--90)

SECTION 8CONTENTS

PageORDERING REPAIR PARTS 8-3. . . . . . . . . . . . . . .Fig. 1 -- Hydraulic Pump Breakdown,

02634 8-4. . . . . . . . . . . . . . . . . . . . . . . .Fig. 2 -- Hydraulic Pump Breakdown,

02704 8-6. . . . . . . . . . . . . . . . . . . . . . . .Fig. 3 -- Hydraulic Pump Breakdown,

13101 8-8. . . . . . . . . . . . . . . . . . . . . . . .Fig. 4 -- Hydraulic Motor Breakdown,






27800 8-14. . . . . . . . . . . . . . . . . . . . . . . .Fig. 10 -- Hydraulic Valve Breakdown,

57982 8-15. . . . . . . . . . . . . . . . . . . . . . . .Fig. 11 -- Hydraulic Solenoid Valve

Breakdown, 13104 8-16. . . . . . . . . . . . .Fig. 12 -- Hydraulic Cylinder Breakdown,

04464 8-17. . . . . . . . . . . . . . . . . . . . . . . .Fig. 13 -- Hydraulic Cylinder Breakdown,

04430 8-18. . . . . . . . . . . . . . . . . . . . . . . .

NOTE: SECTION 8, HYDRAULIC COMPONENTS,lists repair parts for repairable hydraulic components.


365 MM173 (3--90)8-2


8-3365 MM173 (3--90)





SER.NO.

GVW. LBS. KG.




4. Company name.


6. Billing address.























365 MM173 (3--90)8-4

1

2

3

4

5

6

8

910

11

12

14

15

16

17

18

1

1

1

6

7

12

11 13 1

Fig. 1 -- Hydraulic Pump Breakdown, 02634


8-5365 MM173 (3--90)

02321


TENNANT ManufacturerKey Part No. Serial Number Description Qty.

02634 (000000-- ) Pump, Hydraulic 11 55918 (000000-- ) Seal Kit 12 55922 (000000-- ) Bearing Kit, Thrust 13 55931 (000000-- ) Shaft, Pump 14 58925 (000000-- ) Housing Assembly, Pump 1

5 55939 (000000-- ) Bearing, Roller 16 55905 (000000-- ) Bearing, Trunion 27 55933 (000000-- ) Plate, Cam 18 55920 (000000-- ) Rotating Kit 19 57051 (000000-- ) Back Plate 1

10 55937 (000000-- ) Bearing, Roller 111 55941 (000000-- ) Valve, Relief 212 57210 (000000-- ) Plug Assembly 213 55932 (000000-- ) Gerotor And Coupler Assembly 114 37457 (000000-- ) Valve Assembly 2

15 55930 (000000-- ) Pump Adaptor Assembly 116 55906 (000000-- ) Valve, Charge Relief 117 55929 (000000-- ) Bearing, Roller 118 31537 (000000-- ) Cover 1


365 MM173 (3--90)8-6

1

2

3

4

5

6

78

910

11

12

13

14

15

1617

14

13

11

12

1

1

8

1

61

18



8-7365 MM173 (3--90)

04694



02704 (000000-- ) Pump, Hydraulic 11 02711 (000000-- ) Seal Kit 12 55922 (000000-- ) Bearing Kit, Thrust 13 55931 (000000-- ) Shaft, Pump 14 02710 (000000-- ) Key 1

5 55939 (000000-- ) Bearing, Roller 16 02709 (000000-- ) Bearing, Trunnion 27 02708 (000000-- ) Plate, Cam 18 02706 (000000-- ) Rotating Kit 19 02707 (000000-- ) Back Plate 1

10 55937 (000000-- ) Bearing, Roller 111 02650 (000000-- ) Valve, Relief 212 57210 (000000-- ) Plug Assembly 213 55932 (000000-- ) Gerotor and Coupler Assembly 114 37457 (000000-- ) Valve Assembly 2

15 55930 (000000-- ) Pump Adaptor Assembly 116 55906 (000000-- ) Valve, Charge Relief 117 55929 (000000-- ) Bearing, Roller 118 02705 (000000-- ) Bearing, Inner Race 1


365 MM173 (3--90)8-8

111

2 3

4

2

2

03829



13101 (000000-- ) Pump, Hydraulic 11 57064 (000000-- ) Seal Kit 12 82333 (000000-- ) Plate Kit, Back 13 13989 (000000-- ) Gear and Body Kit 14 13966 (000000-- ) Gear, Drive 1


8-9365 MM173 (3--90)

1

2

3

4

5

6

7

2

1

12

01737

Fig. 4 -- Hydraulic Motor Breakdown, 48663


48663 (000000-- ) Motor, Hydraulic 11 33579 (000000-- ) Seal Kit, Shaft 12 33580 (000000-- ) Seal Kit, Rear 13 33694 (000000-- ) Shaft And Bearing Assembly 14 45622 (000000-- ) Nut 1

5 45623 (000000-- ) Key 16 37616 (000000-- ) Drive 17 37756 (000000-- ) Gerotor 1


365 MM173 (3--90)8-10

02613



77101 (000000-- ) Motor, Hydraulic 1SK2561 (000000-- ) Seal Kit 100966 (000000-- ) Key 1


8-11365 MM173 (3--90)

1

2

3

4

5

67

8

2

2

03938



13105 (000000-- ) Motor, Hydraulic 11 34174 (000000-- ) Flange, Mounting 12 47649 (000000-- ) Seal Kit 13 16694 (000000-- ) Shaft, Output 14 34176 (000000-- ) Drive 1

5 87663 (000000-- ) Gerotor 16 16695 (000000-- ) Race, Thrust 17 45628 (000000-- ) Bearing, Thrust 18 00500--15 (000000-- ) Key, Woodruff 1


365 MM173 (3--90)8-12

1

2

4

6

8

9

5

1

17

05349



28808 (000000-- ) Motor, Hydraulic 11 28835 (000000-- ) Seal Kit 12 31354 (000000-- ) Flange, Mounting 1

34175 (000000-- ) Output Shaft Assembly 13 16694 (000000-- ) Shaft, Output 1

4 45628 (000000-- ) Bearing, Thrust 15 16695 (000000-- ) Race, Thrust 16 34176 (000000-- ) Drive 17 31381 (000000-- ) Gerotor Set 18 00500--15 (000000-- ) Key, Woodruff 1


8-13365 MM173 (3--90)

1

2

3

4

5

6 78

92

2

2

03939



13106 (000000-- ) Motor, Hydraulic 11 34174 (000000-- ) Flange, Mounting 12 28835 (000000-- ) Seal Kit 13 37617 (000000-- ) Shaft, Output 14 34176 (000000-- ) Drive 1

5 34177 (000000-- ) Gerotor 16 16695 (000000-- ) Race, Thrust 17 45628 (000000-- ) Thrust, Bearing 18 00500--15 (000000-- ) Key, Woodruff 19 39527 (000000-- ) Nut, Slotted Hex 1


365 MM173 (3--90)8-14

1

2

4

56 7

8

9

10

1

1

1

05347



27800 (000000-- ) Motor, Hydraulic 11 28835 (000000-- ) Seal Kit 12 31354 (000000-- ) Flange, Mounting 1

31374 (000000-- ) Output Shaft Assembly 13 31375 (000000-- ) Shaft, Output 1

4 45628 (000000-- ) Bearing 15 16695 (000000-- ) Race, Thrust 16 31380 (000000-- ) Drive 17 31383 (000000-- ) Gerotor Set 18 00500--15 (000000-- ) Key, Woodruff 1

9 39527 (000000-- ) Nut, Slotted Hex 1


8-15365 MM173 (3--90)

1

23 4

1

1

02319

Fig. 10 -- Hydraulic Valve Breakdown, 57982


57982 (000000-- ) Valve, Hydraulic 11 57152 (000000-- ) Seal Kit 12 57154 (000000-- ) Race, Thrust 13 57155 (000000-- ) Drive 14 57156 (000000-- ) Gerotor 1


365 MM173 (3--90)8-16

03830

Fig. 11 -- Hydraulic Solenoid Valve Breakdown, 13104


13104 (000000-- ) Valve, Hydraulic Solenoid 11 13893 (000000-- ) Seal Kit, Complete 1

13891 (000000-- ) Seal Kit, Partial 12 13909 (000000-- ) Valve, Solenoid 13 13932 (000000-- ) Coil 24 57186 (000000-- ) Coil 1

5 13945 (000000-- ) Coil 16 13947 (000000-- ) Coil 17 13948 (000000-- ) Coil 18 13894 (000000-- ) Valve, Flow Control, 1 (includes seals) 19 13895 (000000-- ) Valve, Flow Control, 2 (includes seals) 1

10 13896 (000000-- ) Valve, Relief, 1 (includes seals) 111 13898 (000000-- ) Valve, Relief, 2 (includes seals) 112 13899 (000000-- ) Valve, Relief, 3 and 4 (includes seals) 213 13902 (000000-- ) Plug, #2 314 13903 (000000-- ) Plug, #4 4

15 13904 (000000-- ) Plug, #6 816 13907 (000000-- ) Plug, #8 117 02607 (000000-- ) Valve, Solenoid (includes seals) 4


8-17365 MM173 (3--90)

1

1

1

03828

Fig. 12 -- Hydraulic Cylinder Breakdown, 04464


04464 (000000-- ) Cylinder, Hydraulic 11 04481 (000000-- ) Seal Kit 1


365 MM173 (3--90)8-18

1

2

3

3

2

1

1

03827

Fig. 13 -- Hydraulic Cylinder Breakdown, 04430


04430 (000000-- ) Cylinder, Hydraulic 11 04483 (000000-- ) Seal Kit 12 13924 (000000-- ) Bearing 23 07259 (000000-- ) Fitting, Grease 2

ENGINE PARTS, GASOLINE, LPG

9-1365 MM173 (3---90)

SECTION 9CONTENTS

PageORDERING REPAIR PARTS 9-3. . . . . . . . . . . . . . .Fig. 1 -- Cylinder Block, Head, and

Manifolds Group 9-4. . . . . . . . . . . . . . .Fig. 2 -- Crankshaft Group 9-5. . . . . . . . . . . . . . . . . .Fig. 3 -- Valves and Valve Cover Group 9-6. . . . . . .Fig. 4 -- Camshaft Group 9-8. . . . . . . . . . . . . . . . . . .Fig. 5 -- Piston and Connecting

Rod Group 9-9. . . . . . . . . . . . . . . . . . . .Fig. 6 -- Oil Pump, Filter, and PCV

Group 9-10. . . . . . . . . . . . . . . . . . . . . . . .Fig. 7 -- Water Pump and Thermostat

Group 9-12. . . . . . . . . . . . . . . . . . . . . . . .Fig. 8 -- Distributor and Spark Plugs

Group 9-13. . . . . . . . . . . . . . . . . . . . . . . .Fig. 9 -- Gasket Kits Group 9-14. . . . . . . . . . . . . . . . .

NOTE: SECTION 12, ENGINE PARTS, GASOLINE,LPG, lists repair parts for gasoline and LPG poweredengines, TENNANT part number 58087, for machinesbelow serial number 007000.


365 MM173 (3---90)9-2


9-3365 MM173 (3---90)





SER.NO.

GVW. LBS. KG.




4. Company name.


6. Billing address.























365 MM173 (3---90)9-4

1

2

3

4

5

6

7

8

9

02311

Fig. 1 -- Cylinder Block, Head, and Manifolds Group

TENNANTr Ford EngineKey Part No. Part Number Serial Number Description Qty.

1 711M--6010--BA (000000-- ) Block, Cylinder 1761F--6011--CA (000000-- ) Block, Cylinder With Pistons, Etc. 1

2 37351 D9ZZ--9278--A (000000-- ) Switch, Oil Pressure 13 DORY--6055--A (000000-- ) Liner, Cylinder Block, Standard 43 DORY--6055--B (000000-- ) Liner, Cylinder Block, 0.020” 0/s 4

4 731M--6059--BA (000000-- ) Front Cover 15 37333 D1FZ--6020--B (000000-- ) Gasket, Front Cover 16 37342 D1FZ--6700--B (000000-- ) Seal, Front Cover Oil 17 761F--6049--AA (000000-- ) Head, Cylinder 18 54911--23 D8RZ--6051--B (000000-- ) Gasket, Cylinder Head 1

9 D1FZ--6065--B (000000-- ) Bolt, Cylinder Head 89 D1FZ--6065--C (000000-- ) Bolt, Cylinder Head 2

38246 761F--9425--AA (000000-- ) Manifold, Intake 1113765--ES2 (000000-- ) Stud, LPG 2

58049 711F--9430--AC (000000-- ) Manifold, Exhaust 1

54911--22 DORY--9441--A (000000-- ) Gasket, Intake Manifold 154911--20 DORY--9448--A (000000-- ) Gasket, Exhaust, Inner 154911--21 DORY--9448--B (000000-- ) Gasket, Exhaust, Outer 2


9-5365 MM173 (3---90)

1

2 34 5

6

7

8

9

1011

12136

6

Serviced only in Block Assembly02312

Fig. 2 -- Crankshaft Group


1 D1FZ--6303--B (000000-- ) Crankshaft 12 37321 DORY--6306--A (000000-- ) Sprocket 13 D1FZ--6310--A (000000-- ) Slinger 14 37343 D1FZ--6701--A (000000-- ) Seal, Crankshaft Rear 15 37312 DORY--6B316--A (000000-- ) Key 1

6 D8RZ--6333--A (000000-- ) Bearing, Standard O.D. and Standard I.D. 56 D8RZ--6333--D (000000-- ) Bearing, Standard O.D. and 0.010”

Undersize I.D. As Req.6 D8RZ--6333--T (000000-- ) Bearing, Standard O.D. and 0.020”

Undersize I.D. As Req.

6 D8RZ--6333--F (000000-- ) Bearing, Standard O.D. and 0.030”Undersize I.D. As Req.

6 D8RZ--6333--AA (000000-- ) Bearing, 0.015” Oversize O.D. andStandard I.D. As Req.

6 D2FZ--6333--C (000000-- ) Bearing, 0.015” Oversize O.D. and0.010” Undersize I.D. As Req.

6 D8RZ--6333--Y (000000-- ) Bearing, 0.015” Oversize O.D. and0.020” Undersize I.D. As Req.

6 D8RZ--6333--Z (000000-- ) Bearing, 0.015” Oversize O.D. and0.030” Undersize I.D. As Req.

7 D1FZ--6345--B (000000-- ) Bolt, Main Bearing Cap 10

8 D1FZ--6335--C (000000-- ) Retainer 19 DORY--6344--A (000000-- ) Gasket 110 37689 D1FZ--6A355--A (000000-- ) Washer, Main Bearing, Standard,2.938” O.D. 210 37330 D1FZ--6A355--c (000000-- ) Washer, Main Bearing, 0.005” O.S. As Req.10 D1FZ--6A355--D (000000-- ) Washer, Main Bearing, 0.0075” O.S. As Req.

10 D1FZ--6A355--E (000000-- ) Washer, Main Bearing, 0.010” O.S. As Req.12 731M--6375--BA (000000-- ) Flywheel 113 37719 D1FZ--6384--A (000000-- ) Gear, Flywheel Ring 1


365 MM173 (3---90)9-6

1

2

3

4

5

6

7

8 9

10

11

12

13

14

15

1617

18

1920

21

22

Fig. 3 -- Valves and Valve Cover Group


9-7365 MM173 (3---90)

02313

Fig. 3 -- Valves and Valve Cover Group


1 D1FZ--6500--A (000000-- ) Tappet, Standard 0.515” Stem O.D. 8D1FZ--6500--B (000000-- ) Tappet, 0.004” Oversize As Req.801M--6507--GA (000000-- ) Valve, Standard, 1 Groove, Intake 4

2 801M--6507--HA (000000-- ) Valve, 0.015” Oversize, 1 Groove,Intake As Req.

2 37368 731M--6505--AA (000000-- ) Valve, Standard, 1 Groove, Exhaust 42 731M--6505--CA (000000-- ) Valve, 0.015” Oversize, 1 Groove,

Exhaust As Req.3 37308 DORY--6510--A (000000-- ) Bushing, Valve Guide, Intake,

1.825”, Plain As Req.

3 DORY--6510--C (000000-- ) Bushing, Valve Guide, Intake,1.825”, Shouldered As Req.

3 37309 DORY--6510--B (000000-- ) Bushing, Valve Guide, Exhaust,2.075”, Plain As Req.

3 DORY--6510--D (000000-- ) Bushing, Valve Guide, Exhaust,2.075”, Shouldered As Req.

4 37340 D1FZ--6513--D (000000-- ) Spring 85 D1FZ--6514--B (000000-- ) Retainer 86 2724E--6518--A (000000-- ) Key 167 DORY--6A527--A (000000-- ) Bolt 48 DORY--6A528--A (000000-- ) Washer 4

9 DORY--6531--A (000000-- ) Support 410 37693 DORY--6549--B (000000-- ) Screw 811 50352 D1FZ--6766--B (000000-- ) Cap 112 DORY--6563--B (000000-- ) Shaft 113 72034--S (000000-- ) Pin, Cotter, 1” Long 2

14 DORY--6026--D (000000-- ) Plug 215 DORY--6564--D (000000-- ) Arm, R.H. 415 DORY--6564--C (000000-- ) Arm, L.H. 416 DORY--6565--A (000000-- ) Rod, Push 817 38250 E2JL--6571--AA (000000-- ) Seal 8

18 DORY--6587--A (000000-- ) Spring, Valve Rocker To Shaft 319 DORY--6590--A (000000-- ) Washer, Flat Type 420 DORY--6598--A (000000-- ) Washer, Spring Type 221 37358 701M6582--GA (000000-- ) Cover 122 54911--24 D1FZ--6584--C (000000-- ) Gasket 1


365 MM173 (3---90)9-8

1

2

3

4

567

8

9

10

11

1312

00746

Fig. 4 -- Camshaft Group


1 711F--6250--DA (000000-- ) Camshaft 12 DORY--6253--A (000000-- ) Dowel 13 DORY--6255--A (000000-- ) Retainer 14 37315 DORY--6256--A (000000-- ) Sprocket 15 DORY--6258--A (000000-- ) Retainer 1

6 37316 DORY--6261--A (000000-- ) Bearing, Front, Standard I.D. and O.D. 16 37317 DORY--6261--B (000000-- ) Bearing, Front, Standard I.D. and

0.020” O.S. -- O.D. As Req.7 37306 DORY--6262--A (000000-- ) Bearing, Center, Standard I.D. and O.D. 17 38242 DORY--6262--B (000000-- ) Bearing, Center, Standard I.D. and

0.020” O.S. -- O.D. As Req.

8 DORY--6263--A (000000-- ) Bearing, Rear, Standard I.D. and O.D. 18 DORY--6263--B (000000-- ) Bearing, Rear, Standard I.D. and

0.020” O.S. -- O.D. As Req.9 37307 DORY--6268--A (000000-- ) Chain 110 DORY--6269--A (000000-- ) Plate 1

11 37337 D1FZ--6284--A (000000-- ) Tensioner 112 37338 D1FZ--6285--A (000000-- ) Arm 113 37694 D1FZ--6286--A (000000-- ) Pin 1


9-9365 MM173 (3---90)

1

2 3

4

56

7

8

5

00742

Fig. 5 -- Piston and Connecting Rod Group


1 751M--6102--ARB (000000-- ) Piston, Standard 41 751M--6102--AUB (000000-- ) Piston, 0.030” O/s As Req.2 DORY--6135--A (000000-- ) Pin, Standard 42 DORY--6135--C (000000-- ) Pin, 0.002” Undersize As Req.3 DORY--6140--A (000000-- ) Retainer, Pin 8

4 751M--6149--AA (000000-- ) Ring Set, Piston, Standard 14 751M--6149--DA (000000-- ) Ring, Piston, 0.030” O/s As Req.5 DORY--6200--A (000000-- ) Rod Assembly 46 105e--6207--B (000000-- ) Bushing 47 38243 D1FZ--6211--AA (000000-- ) Bearing, Standard 8

7 D1FZ--6211--AB (000000-- ) Bearing, 0.001” Undersize As Req.7 D1FZ--6211--AC (000000-- ) Bearing, 0.002” Undersize As Req.7 37335 D1FZ--6211--AD (000000-- ) Bearing, 0.010” Undersize As Req.7 D1FZ--6211--AE (000000-- ) Bearing, 0.020” Undersize As Req.7 D1FZ--6211--AF (000000-- ) Bearing, 0.030” Undersize As Req.

7 D1FZ--6211--AG (000000-- ) Bearing, 0.040” Undersize As Req.8 DORY--6214--A (000000-- ) Bolt, 0.38” -- 24 X 1.718” 8


365 MM173 (3---90)9-10

1

23

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

Fig. 6 -- Oil Pump, Filter, and PCV Group


9-11365 MM173 (3---90)

02314

Fig. 6 -- Oil Pump, Filter, and PCV Group


1 37844 731M--6600--AA (000000-- ) Oil Pump 12 D1FZ--6608--B (000000-- ) Rotor and Shaft 13 37403 116682--ES (000000-- ) O--Ring 14 DORY--6622--A (000000-- ) Tube, Oil Pickup 15 DORY--6652--A (000000-- ) Gear 1

6 72432--S (000000-- ) Pin 17 DORY--6K656--A (000000-- ) Tube, Oil Return 18 37341 D1FZ--6659--A (000000-- ) Gasket 19 DORY--6A665--A (000000-- ) Adaptor, Crankcase Ventilation 110 38245 73HF--6A666--AB (000000-- ) Valve, Crankcase Ventilation, PCV 1

11 751F--6K609--AB (000000-- ) Hose, PCV 112 DORY--6670--A (000000-- ) Spring 113 DORY--6674--A (000000-- ) Plunger 114 58122 FL--271 (000000-- ) Oil Filter 115 37326 DORY--6675--C (000000-- ) Oil Pan 1

16 37354 D6TZ--6730--A (000000-- ) Plug, Oil Drain 117 37303 C20Z--6734--A (000000-- ) Gasket, Oil Drain 118 54911--27 DORY--6754--A (000000-- ) Tube, Oil Level Indicator 119 DORY--6K777--A (000000-- ) O--Ring 120 37344 D1FZ--6781--B (000000-- ) Gasket, Oil Pan 1

21 D1FZ--6A785--B (000000-- ) Separator 122 D1FZ--6890--B (000000-- ) Insert, Oil Filter Mounting Bolt 123 C8SZ--6A892--A (000000-- ) Grommet, PCV Valve 1


365 MM173 (3---90)9-12

1

2

3

4

5

6

02315

Fig. 7 -- Water Pump and Thermostat Group


1 33864 (000000-- ) Replacement Kit, Water Pump 12 37325 DORY--8507--A (000000-- ) Gasket 13 DORY--8553--A (000000-- ) Hub 14 51839 (000000-- ) Fitting, Elbow 15 54911--25 D1FZ--8255B (000000-- ) Gasket 1

6 37327 D4PZ--8575--A (000000-- ) Thermostat 1


9-13365 MM173 (3---90)

7

8

4

2

3

1

9

5

6

04411

Fig. 8 -- Distributor and Spark Plugs Group


1 06997 (000000-- ) Distributor Kit 12 82697 (000000-- ) Rotor, Overspeed Protection 13 58507 D1FZ--2106--A (000000-- ) Cap 14 58506 77BF--12171--AA (000000-- ) Points Set 15 58509 831F--12300--AA (000000-- ) Condenser 1

37328 D1FZ--12259--A (000000-- ) Wire Kit, Ignition 16 721F--12283--BA (000000-- ) Wire, No. 2 1

721F--12284--AA (000000-- ) Wire, No. 3 1721F--12286--BA (000000-- ) Wire, No. 1 1721F--12287--AA (000000-- ) Wire, No. 4 1

7 45770--8 AGR--22 (000000-- ) Spark Plug 48 07328 (000000-- ) Filter, Distributor Cap 19 07330 (000000-- ) Filter, Distributor 1

NOTE: To identify parts shown but not listed here, see SECTION 5, STANDARD MODEL PARTS.


365 MM173 (3---90)9-14

1

1

1

1

1

2

2

2

2

1

00749

Fig. 9 -- Gasket Kits Group


1 37332 D1FZ--6008--A (000000-- ) Gasket Kit, Engine Overhaul 12 37334 D1FZ--6079--A (000000-- ) Gasket Kit, Valve Grind 1

ENGINE PARTS, DIS, GASOLINE, LPG

10-1365 MM173 (3--90)

SECTION 10CONTENTS

PageORDERING REPAIR PARTS 10-3. . . . . . . . . . . . . . .Fig. 1 -- Cylinder Head, Valves Group 10-4. . . . . . . .Fig. 2 -- Cylinder Block Group 10-6. . . . . . . . . . . . . .Fig. 3 -- Camshaft and Valve Control Group 10-8. .Fig. 4 -- Crankshaft and Piston Group 10-10. . . . . . . .Fig. 5 -- Oil Pump and Oil Pan Group 10-12. . . . . . . .Fig. 6 -- Intake Manifold Group 10-14. . . . . . . . . . . . . .Fig. 7 -- Front Cover Assembly Group 10-15. . . . . . .Fig. 8 -- Water Pump Group 10-16. . . . . . . . . . . . . . . .Fig. 9 -- Distributorless Ignition Group 10-17. . . . . . . .Fig. 10 -- Gaskets Group 10-18. . . . . . . . . . . . . . . . . . .Fig. 11 -- Flywheel Group 10-19. . . . . . . . . . . . . . . . . . .

NOTE: SECTION 10, ENGINE PARTS, DIS,GASOLINE, LPG, lists repair parts for Distributorless(DIS) Gasoline and LPG Engines, TENNANT PartNo. 30296, for machines serial number 007000 andabove.


365 MM173 (3--90)10-2


10-3365 MM173 (3--90)





SER.NO.

GVW. LBS. KG.




4. Company name.


6. Billing address.























365 MM173 (3--90)10-4

1

2

3

4

5

6

7

8

910

11

12

13

14

15

1617

18

Fig. 1 -- Cylinder Head, Valves Group



10-5365 MM173 (3--90)

05498

Fig. 1 -- Cylinder Head, Valves Group


1 36279 89BM--6049--DD (000000-- ) Head Assembly, Cylinder 12 36281 89BM--6051--C1C (000000-- ) Gasket, Cylinder Head 13 36297 89BM--6065--DA (000000-- ) Bolt, Cylinder Head 104 36298 E840126--S (000000-- ) Dowel, Cylinder Head to Block 25 36300 89BM--6507--BA (000000-- ) Valve, Intake, Std 4

5 36303 89BM--6507--BC (000000-- ) Valve, Intake, 0.40 mm O/S As Req.6 36306 89BM--6505--BC (000000-- ) Valve, Exhaust, 0.40 mm O/S As Req.6 36307 89BM--6505--CA (000000-- ) Valve, Exhaust, Std 47 36315 89BM--6513--AA (000000-- ) Spring, Valve 88 36317 D1FZ--6571--B (000000-- ) Seal, Valve Stem 8

9 36318 89BM--6A536--AA (000000-- ) Retainer 810 36319 88WM--6518--AA (000000-- ) Lock, Valve Spring 1611 36321 89BM--6582--AA (000000-- ) Cover, Rocker Arm 112 07705 77BM--6584--CA (000000-- ) Gasket, Rocker Arm Cover 113 36324 E800516--S72 (000000-- ) Screw, Rocker Cover to Head 4

14 36325 118297--ES8 (000000-- ) Washer, Flat, 6 mm, 415 36265 D8RZ--6026--B (000000-- ) Plug 116 36330 89BM--6057--A2E (000000-- ) Insert, Exhaust Valve Seat 417 36331 89BM--6056--A1G (000000-- ) Insert, Intake Valve Seat 418 30327 (000000-- ) Stud 8


365 MM173 (3--90)10-6

1

2

3

4

5

6

7

8

9

10

11

4

4

Fig. 2 -- Cylinder Block Group



10-7365 MM173 (3--90)

05497

Fig. 2 -- Cylinder Block Group


1 36264 89BM--6011--DA (000000-- ) Block, Cylinder, With Crank,Pistons, Rings, etc. 1

36263 89BM--6010--FA (000000-- ) Block, Cylinder 12 36265 D8RZ--6026--B (000000-- ) Plug 23 36267 D8RZ--6026--A (000000-- ) Plug 1

4 36268 87837--S (000000-- ) Plug, 1/4 NPT 35 36272 353055--S7 (000000-- ) Plug, 1/4 NPT 16 36273 E890100--S (000000-- ) Plug, Ball, Oil Gallery 17 36274 D8RZ--6767--A (000000-- ) Adapter 18 36275 89BM--6055--BA (000000-- ) Liner, Cylinder As Req.

9 36276 D1FZ--6345--A (000000-- ) Bolt, Main Bearing Cap 1010 36277 89BF--6C315--AA (000000-- ) Transducer 111 36278 E802666--S72 (000000-- ) Screw, M6 x 14 1


365 MM173 (3--90)10-8

Fig. 3 -- Camshaft and Valve Control Group


10-9365 MM173 (6--90)

05500

Fig. 3 -- Camshaft and Valve Control Group


1 36340 89BM--6251--BA (000000-- ) Camshaft 12 37316 DORY--6261--A (000000-- ) Bearing, Std ID -- Std OD 12 37317 DORY--6261--B (000000-- ) Bearing, Std ID + 0.020 OD As Req.3 37306 DORY--6262--A (000000-- ) Bearing, Std ID -- Std OD 13 38242 DORY--6262--B (000000-- ) Bearing, Std ID + 0.020 OD As Req.

4 37306 DORY--6262--A (000000-- ) Bearing, Std ID -- Std OD 14 38242 DORY--6262--B (000000-- ) Bearing, Std ID + 0.020 OD As Req.5 36341 DORY--6253--A (000000-- ) Dowel 16 36342 DORY--6269--A (000000-- ) Plate, Thrust 17 36343 DORY--6255--A (000000-- ) Retainer 1

8 36344 E602166--S72 (000000-- ) Bolt, M6 x 16, Tensioner to Block 29 36345 77BM--6256--AA (000000-- ) Sprocket, Camshaft 110 36348 DORY--6258--A (000000-- ) Retainer 111 36349 E602351--S72 (000000-- ) Bolt, M8 x 16 212 37307 DORY--6268--A (000000-- ) Chain 1

13 37337 D1FZ--6284--A (000000-- ) Tensioner 114 36372 E600116--S72 (000000-- ) Bolt, M6 x 55, Tensioner to Block 115 36344 E602166--S72 (000000-- ) Bolt, M6 x 16, Tensioner to Block 116 36373 34805--S8 (000000-- ) Washer, 1/4 Lock 217 36374 77BM--6K255--AB (000000-- ) Arm, Tensioner 1

18 37694 D1FZ--6286--A (000000-- ) Pin 119 36375 89BM--6500--AA (000000-- ) Tappet, Std 820 36381 89BM--6565--AA (000000-- ) Rod, Valve Push 821 36382 89BM--6529--AB (000000-- ) Arm, Valve Rocker, Right, With Screw 421 36383 89BM--6K528--AB (000000-- ) Arm, Valve Rocker, Left, With Screw 4

22 37693 DORY--6549--B (000000-- ) Screw 823 36384 77BM--6531--BB (000000-- ) Support, Rocker Arm Shaft 424 36389 E630031--S101 (000000-- ) Washer, B10 x 20 x 2.5 425 36390 E800509--S72 (000000-- ) Bolt, Rocker Support 426 36402 DORY--6587--A (000000-- ) Spring, Locating 3

27 36405 77BM--6A557--BB (000000-- ) Shaft Assembly, Rocker Arm 128 36406 D1FZ--6026--E (000000-- ) Plug, Rocker Arm Shaft, 11 mm 229 36407 77BM--6598--AB (000000-- ) Washer, Spring 230 36408 116106--ES10 (000000-- ) Washer, Flat 231 36409 72025--S7 (000000-- ) Pin, Cotter, 2.3 mm 2


365 MM173 (3--90)10-10

1

2

3

4

56

78

9

10

1112

13

1415

16

17

18

19

2021

2

2

2

2

2

3

18

Fig. 4 -- Crankshaft and Piston Group


10-11365 MM173 (3--90)

05501

Fig. 4 -- Crankshaft and Piston Group


1 36322 89BM--6303--DA (000000-- ) Crankshaft Assembly 12 36410 89BM--6333--AA (000000-- ) Main Bearing, Crankshaft,

Std OD, Std ID 52 36411 89BM--6333--BA (000000-- ) Main Bearing, Crankshaft,

Std OD, 0.005 US ID As Req.

2 36412 89BM--6333--CA (000000-- ) Main Bearing, Crankshaft,Std OD, 0.010 US ID As Req.

2 36413 89BM--6333--DA (000000-- ) Main Bearing, Crankshaft,0.015 OS OD, Std ID As Req.

2 36414 89BM--6333--EA (000000-- ) Main Bearing, Crankshaft,

Std OD, 0.020 US ID As Req.2 36415 89BM--6333--FA (000000-- ) Main Bearing, Crankshaft,

Std OD, 0.030 US ID As Req.2 36416 89BM--6333--GA (000000-- ) Main Bearing, Crankshaft,

0.015 OS OD, 0.010 US ID As Req.

2 36418 89BM--6333--HA (000000-- ) Main Bearing, Crankshaft,0.015 OS OD, 0.020 US ID As Req.

3 36419 89BM--6A341--AA (000000-- ) Washer, Main Bearing Thrust, Std 23 36421 89BM--6A341--BA (000000-- ) Washer, Main Bearing Thrust,

0.015 OS As Req.

4 36422 89BM--6312--AA (000000-- ) Pulley, Crankshaft, 1 Groove 15 36423 89BM--6K340--AA (000000-- ) Bolt, Pulley to Crankshaft, M12 x 32 16 07707 E830135--S76 (000000-- ) Washer, Pulley to Crankshaft, B12 17 36257 83BM--6700--A4A (000000-- ) Seal, Front Cover 18 36424 D8RZ--6310--A (000000-- ) Slinger, Oil 1

9 37321 DORY--6306--A (000000-- ) Sprocket 110 36429 DORY--6B316--A (000000-- ) Key, Woodruff 111 36259 89BM--6344--BA (000000-- ) Gasket, Rear Retainer 112 36430 86BM--6K318--AA (000000-- ) Retainer Assembly, Rear 113 36262 D7RZ--6701--A (000000-- ) Seal, Crankshaft Rear 1

14 36431 E630173--S71M (000000-- ) Washer, B8 Lock 415 37181 E602187--S82 (000000-- ) Bolt, M8 x 20 416 36432 89BM--6102--DA (000000-- ) Piston, Pin and Ring Assembly, Std 416 36433 89BM--6102--EA (000000-- ) Piston, Pin and Ring Assembly,

0.020 OS As Req.

16 36445 89BM--6102--FA (000000-- ) Piston, Pin and Ring Assembly,0.040 OS As Req.

17 36450 84BM--6148--DA (000000-- ) Ring Set, Piston, Std 417 36451 84BM--6148--EA (000000-- ) Ring Set, Piston, 0.020 OS As Req.17 36452 84BM--6148--FA (000000-- ) Ring Set, Piston, 0.040 OS As Req.

18 36453 86BM--6200--AA (000000-- ) Rod Assembly, Connecting 419 36454 89BM--6214--CB (000000-- ) Bolt, Connecting Rod 820 36463 89SM--6211--AA (000000-- ) Bearing, Connecting Rod, Std 820 36467 89SM--6211--BA (000000-- ) Bearing, Connecting Rod, 0.001 US As Req.20 36469 89SM--6211--CA (000000-- ) Bearing, Connecting Rod, 0.010 US As Req.

20 36483 89SM--6211--DA (000000-- ) Bearing, Connecting Rod, 0.020 US As Req.20 36493 89SM--6211--EA (000000-- ) Bearing, Connecting Rod, 0.030 US As Req.21 36590 116336--ES100 (000000-- ) Dowel Pin, Connecting Rod 8


365 MM173 (3--90)10-12

1

2

3

4

5

6

7

8

9

101112

13

14

15

1617

18

19

18

18

21

20

Fig. 5 -- Oil Pump and Oil Pan Group



10-13365 MM173 (3--90)

05503

Fig. 5 -- Oil Pump and Oil Pan Group


1 07710 D8RZ--6600--A (000000-- ) Pump, Oil 12 36748 E800519--S72 (000000-- ) Bolt 33 36431 E630173--S71M (000000-- ) Washer, B8 Lock 34 36764 89BM--6659--AA (000000-- ) Gasket, Oil Pump to Block 15 36765 86BM--6617--AA (000000-- ) Tube Assembly, Oil Pickup 1

6 10075 D1FZ--6608--B (000000-- ) Rotor and Shaft 17 36776 116682--ES (000000-- ) Seal, Cover Plate 18 36780 DORY--6652--A (000000-- ) Gear 19 36867 72432--S (000000-- ) Pin, Drive Gear 110 36881 DORY--6674--A (000000-- ) Plunger 1

11 36904 DORY--6670--A (000000-- ) Spring 112 36923 DORY--6666--A (000000-- ) Plug 113 36924 89BM--6750--AA (000000-- ) Indicator, Oil Level 114 37053 89BM--6784--AA (000000-- ) Tube, Oil Level Indicator 115 37098 86BM--6675--AA (000000-- ) Oil Pan 1

16 37099 E602165--S72 (000000-- ) Bolt, M6 x 14, Oil Pan 1817 36373 34805--S8 (000000-- ) Washer, 1/4 Lock 1818 10806 A850X--6013--AA (000000-- ) Kit, Oil Pan Gasket 119 37127 EOFZ--6730--B (000000-- ) Plug, Oil Drain 120 37157 EOFZ--6734--A (000000-- ) Gasket, Oil Drain Plug 1

21 19205 (000000-- ) Filter, Engine Oil 1


365 MM173 (3--90)10-14

1

2

3

4

5

05506

Fig. 6 -- Intake Manifold Group


1 37194 89BF--9424--AD (000000-- ) Manifold, Intake 12 37195 89BM--9441--AB (000000-- ) Gasket, Intake Manifold 13 37196 E800157--S72 (000000-- ) Bolt, M8 x 25 64 37198 77BF--9K442--AA (000000-- ) Adapter, Vacuum 15 37199 E4AF--12A648--AA (000000-- ) Sensor, Water Temperature 1


10-15365 MM173 (3--90)

1

2

3

4

5

6

7

7

7

05499

Fig. 7 -- Front Cover Assembly Group


1 36332 89BM--6019--AA (000000-- ) Cover and Seal Assembly,Cylinder Front 1

2 36258 89BM--6020--AA (000000-- ) Gasket, Front Cover 13 36333 83BM--6700--A3A (000000-- ) Seal, Front Cover 14 36337 E800518--S72 (000000-- ) Bolt, M6 x 45, Front Cover to Block 1

5 39047 E800113--S72 (000000-- ) Bolt, M6 x 40, Front Cover to Block 36 36338 E800512--S72 (000000-- ) Bolt, M6 x 18, Front Cover to Block 47 36339 E630152--S71 (000000-- ) Washer, Lock, B6, Front Cover

and W/P to Block 8


365 MM173 (3--90)10-16

3

4

2

6

5

1

ThermostatHousingAssembly

05509

Fig. 8 -- Water Pump Group


1 37181 E602187--S82 (000000-- ) Bolt, M8 x 20 22 36431 E630173--S71M (000000-- ) Washer, B8 Lock 23 37327 RT--351 (000000-- ) Thermostat 14 37188 89BM--8501--BD (000000-- ) Water Pump 15 37189 89BM--8507--AA (000000-- ) Gasket, Water Pump 1

6 37193 E600113--S72 (000000-- ) Bolt, M6 x 40, Front Cover andW/P to Block 3



10-17365 MM173 (6--90)

1

2

3

45

6

7

8

910

2

05508

Fig. 9 -- Distributorless Ignition Group


1 39025 89BF--12024--AB (000000-- ) Coil and Bracket Assembly, Ignition 12 39026 E804335--S201 (000000-- ) Screw, M8 x 14 3

39035 E8JL--12A200--AC (000000-- ) Wiring Harness, Ignition 13 39038 89BF--12286--AC (000000-- ) Wire, Spark Plug, No. 1 14 39040 89BF--12283--AC (000000-- ) Wire, Spark Plug, No. 2 1

5 39041 89BF--12284--AC (000000-- ) Wire, Spark Plug, No. 3 16 39042 89BF--12287--AC (000000-- ) Wire, Spark Plug, No. 4 17 39043 E865648--S (000000-- ) Separator, Ignition Wire 18 39044 89BF--12297--AA (000000-- ) Separator, Ignition Wire 19 39045 E802166--S76 (000000-- ) Screw, M4 x 10 1

10 39046 87YF--12405--AA (000000-- ) Spark Plug 4


365 MM173 (3--90)10-18

1

2

1 1

1

05495

Fig. 10 -- Gaskets Group


36253 88BX--6008--BA (000000-- ) Engine Gasket Kit, Complete 11 36254 88BX--6014--BA (000000-- ) Engine Gasket Kit, Upper 12 10806 A850X--6013--AA (000000-- ) Engine Gasket Kit, Oil Pan 1



10-19365 MM173 (3--90)

1

2

05502

Fig. 11 -- Flywheel Group


1 36591 89BM--6375--BA (000000-- ) Flywheel and Ring Gear Assembly 12 36630 D2RY--6379--A (000000-- ) Bolt, M10 x 22.5, Flywheel to Crankshaft 6

36646 D1FZ--6397--B (000000-- ) Dowel 6


365 MM173 (3--90)10-20

CROSS REFERENCE

11-1365 MM173 (6--90)

SECTION 11CONTENTS

PagePART NUMBER TO PAGE NUMBER CROSS

REFERENCE LIST 11--1. . . . . . . . . . . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-2

CROSS REFERENCE

11-3365 MM173 (6--90)

PART NUMBER TO PAGE NUMBER CROSS REFERENCE LIST

Part PageNumber Number

A850X--6013--AA 10--12, 10--18. .AGR--22 9--13. . . . . . . . .C20Z--6734--A 9--10. . . .C8SZ--6A892--A 9--10. . .D1FZ--12259--A 9--13. . .D1FZ--2106--A 9--13. . . .D1FZ--6008--A 9--14. . . .D1FZ--6020--B 9--4. . . .D1FZ--6026--E 10--8. . . .D1FZ--6065--B 9--4. . . .D1FZ--6065--C 9--4. . . .D1FZ--6079--A 9--14. . . .D1FZ--6211--AA 9--9. . .D1FZ--6211--AB 9--9. . .D1FZ--6211--AC 9--9. . .D1FZ--6211--AD 9--9. . .D1FZ--6211--AE 9--9. . .D1FZ--6211--AF 9--9. . .D1FZ--6211--AG 9--9. . .D1FZ--6284--A 9--8, 10--8. . . .D1FZ--6285--A 9--8. . . .D1FZ--6286--A 9--8, 10--8. . . .D1FZ--6303--B 9--5. . . .D1FZ--6310--A 9--5. . . .D1FZ--6335--C 9--5. . . .D1FZ--6345--A 10--6. . . .D1FZ--6345--B 9--5. . . .D1FZ--6384--A 9--5. . . .D1FZ--6397--B 10--19. . . .D1FZ--6500--A 9--6. . . .D1FZ--6500--B 9--6. . . .D1FZ--6513--D 9--6. . . .D1FZ--6514--B 9--6. . . .D1FZ--6571--B 10--4. . . .D1FZ--6584--C 9--6. . . .D1FZ--6608--B 9--10, 10--12. . . .D1FZ--6659--A 9--10. . . .D1FZ--6700--B 9--4. . . .D1FZ--6701--A 9--5. . . .D1FZ--6766--B 9--6. . . .D1FZ--6781--B 9--10. . . .D1FZ--6890--B 9--10. . . .D1FZ--6A355--A 9--5. . .D1FZ--6A355--D 9--5. . .D1FZ--6A355--E 9--5. . .D1FZ--6A355--C 9--5. . .D1FZ--6A785--B 9--10. . .D1FZ--8255B 9--12. . . . .D2FZ--6333--C 9--5. . . .D2RY--6379--A 10--19. . . .D4PZ--8575--A 9--12. . . .D6TZ--6730--A 9--10. . . .D7RZ--6701--A 10--10. . . .D8RZ--6026--A 10--6. . . .D8RZ--6026--B 10--4, 10--6. . . .D8RZ--6051--B 9--4. . . .


D8RZ--6310--A 10--10. . . .D8RZ--6333--A 9--5. . . .D8RZ--6333--AA 9--5. . .D8RZ--6333--D 9--5. . . .D8RZ--6333--F 9--5. . . .D8RZ--6333--T 9--5. . . .D8RZ--6333--Y 9--5. . . .D8RZ--6333--Z 9--5. . . .D8RZ--6600--A 10--12. . . .D8RZ--6767--A 10--6. . . .D9ZZ--9278--A 9--4. . . .DORY--6026--D 9--6. . .DORY--6055--A 9--4. . .DORY--6055--B 9--4. . .DORY--6135--A 9--9. . .DORY--6135--C 9--9. . .DORY--6140--A 9--9. . .DORY--6200--A 9--9. . .DORY--6214--A 9--9. . .DORY--6253--A 9--8, 10--8. . .DORY--6255--A 9--8, 10--8. . .DORY--6256--A 9--8. . .DORY--6258--A 9--8, 10--8. . .DORY--6261--A 9--8, 10--8. . .DORY--6261--B 10--8. . .DORY--6261--B 9--8. . .DORY--6262--A 9--8, 10--8. . .DORY--6262--B 9--8, 10--8. . .DORY--6263--A 9--8. . .DORY--6263--B 9--8. . .DORY--6268--A 9--8, 10--8. . .DORY--6269--A 9--8, 10--8. . .DORY--6306--A 9--5, 10--10. . .DORY--6344--A 9--5. . .DORY--6510--A 9--6. . .DORY--6510--B 9--6. . .DORY--6510--C 9--6. . .DORY--6510--D 9--6. . .DORY--6531--A 9--6. . .DORY--6549--B 9--6, 10--8. . .DORY--6563--B 9--6. . .DORY--6564--C 9--6. . .DORY--6564--D 9--6. . .DORY--6565--A 9--6. . .DORY--6587--A 9--6, 10--8. . .DORY--6590--A 9--6. . .DORY--6598--A 9--6. . .DORY--6622--A 9--10. . .DORY--6652--A 9--10, 10--12. . .DORY--6666--A 10--12. . .DORY--6670--A 9--10, 10--12. . .DORY--6674--A 9--10, 10--12. . .DORY--6675--C 9--10. . .DORY--6754--A 9--10. . .DORY--6A527--A 9--6. .DORY--6A528--A 9--6. .

CROSS REFERENCE

365 MM173 (6--90)11-4


DORY--6A665--A 9--10. .DORY--6B316--A 9--5, 10--10. .DORY--6K656--A 9--10. .DORY--6K777--A 9--10. .DORY--8507--A 9--12. . .DORY--8553--A 9--12. . .DORY--9441--A 9--4. . .DORY--9448--A 9--4. . .DORY--9448--B 9--4. . .E2JL--6571--AA 9--6. . .E4AF--12A648--AA 10--14E600113--S72 10--16. . . . .E600116--S72 10--8. . . . .E602165--S72 10--12. . . .E602166--S72 10--8. . . .E602187--S82 10--10, 10--16. . . .E602351--S72 10--8. . . .E630031--S101 10--8. . .E630152--S71 10--15. . . .E630173--S71M 10--10, 10--12. . .E630173--S71M 10--16. . .E800113--S72 10--15. . . . .E800157--S72 10--14. . . .E800509--S72 10--8. . . .E800512--S72 10--15. . . .E800516--S72 10--4. . . .E800518--S72 10--15. . . .E800519--S72 10--12. . . .E802166--S76 10--17. . . .E802666--S72 10--6. . . .E804335--S201 10--17. . .E830135--S76 10--10. . . .E840126--S 10--4. . . . . . .E865648--S 10--17. . . . . . .E890100--S 10--6. . . . . . .E8JL--12A200--AC 10--17.EOFZ--6730--B 10--12. . . .EOFZ--6734--A 10--12. . . .FL--271 9--10. . . . . . . . . .RT--351 10--16. . . . . . . . . .SK1444 6--4. . . . . . . . . .SK2136 5--48. . . . . . . . . .SK2137 5--48. . . . . . . . . .SK2498 7--20. . . . . . . . . .SK2498 7--24. . . . . . . . . .SK2561 8--10. . . . . . . . . .73HF--6A666--AB 9--10. .77BF--12171--AA 9--13. .77BF--9K442--AA 10--14. .77BM--6256--AA 10--8. . .77BM--6531--BB 10--8. . .77BM--6584--CA 10--4. .77BM--6598--AB 10--8. . .77BM--6A557--BB 10--8.77BM--6K255--AB 10--8.83BM--6700--A3A 10--15.83BM--6700--A4A 10--10.84BM--6148--DA 10--10. .84BM--6148--EA 10--10. . .84BM--6148--FA 10--10. . .


86BM--6200--AA 10--10. . .86BM--6617--AA 10--12. . .86BM--6675--AA 10--12. . .86BM--6K318--AA 10--10.87YF--12405--AA 10--17. .88BX--6008--BA 10--18. . .88BX--6014--BA 10--18. . .88WM--6518--AA 10--4. .89BF--12024--AB 10--17. .89BF--12283--AC 10--17. .89BF--12284--AC 10--17. .89BF--12286--AC 10--17. .89BF--12287--AC 10--17. .89BF--12297--AA 10--17. .89BF--6C315--AA 10--6. .89BF--9424--AD 10--14. . .89BM--6010--FA 10--6. . .89BM--6011--DA 10--6. . .89BM--6019--AA 10--15. . .89BM--6020--AA 10--15. . .89BM--6049--DD 10--4. .89BM--6051--C1C 10--4.89BM--6055--BA 10--6. . .89BM--6056--A1G 10--4.89BM--6057--A2E 10--4.89BM--6065--DA 10--4. .89BM--6102--DA 10--10. .89BM--6102--EA 10--10. . .89BM--6102--FA 10--10. . .89BM--6214--CB 10--10. .89BM--6251--BA 10--8. . .89BM--6303--DA 10--10. .89BM--6312--AA 10--10. . .89BM--6333--AA 10--10. . .89BM--6333--BA 10--10. . .89BM--6333--CA 10--10. .89BM--6333--DA 10--10. .89BM--6333--EA 10--10. . .89BM--6333--FA 10--10. . .89BM--6333--GA 10--10. .89BM--6333--HA 10--10. .89BM--6344--BA 10--10. . .89BM--6375--BA 10--19. . .89BM--6500--AA 10--8. . .89BM--6505--BC 10--4. .89BM--6505--CA 10--4. .89BM--6507--BA 10--4. . .89BM--6507--BC 10--4. .89BM--6513--AA 10--4. . .89BM--6529--AB 10--8. . .89BM--6565--AA 10--8. . .89BM--6582--AA 10--4. . .89BM--6659--AA 10--12. . .89BM--6750--AA 10--12. . .89BM--6784--AA 10--12. . .89BM--6A341--AA 10--10.89BM--6A341--BA 10--10.89BM--6A536--AA 10--4.89BM--6K340--AA 10--10.89BM--6K528--AB 10--8.

CROSS REFERENCE

11-5365 MM173 (6--90)


89BM--8501--BD 10--16. .89BM--8507--AA 10--16. . .89BM--9441--AB 10--14. . .89SM--6211--AA 10--10. . .89SM--6211--BA 10--10. . .89SM--6211--CA 10--10. . .89SM--6211--DA 10--10. . .89SM--6211--EA 10--10. . .105E--6207--B 9--9. . . .00500--5 5--14. . . . . . . . .00500--15 8--11, 8--12, 8--13, 8--14. . . . . . . .701M6582--GA 9--6. . . .711F--6250--DA 9--8. . .711F--9430--AC 9--4. . .711M--6010--BA 9--4. . .721F--12283--BA 9--13. .721F--12284--AA 9--13. .721F--12286--BA 9--13. .721F--12287--AA 9--13. .731M--6059--BA 9--4. . .731M--6375--BA 9--5. . .731M--6505--AA 9--6. . .731M--6505--CA 9--6. . .731M--6600--AA 9--10. . .751F--6K609--AB 9--10. .751M--6102--ARB 9--9.751M--6102--AUB 9--9.751M--6149--AA 9--9. . .751M--6149--DA 9--9. . .761F--6011--CA 9--4. . .761F--6049--AA 9--4. . .761F--9425--AA 9--4. . .801M--6507--GA 9--6. . .801M--6507--HA 9--6. . .831F--12300--AA 9--13. .00912 5--64, 5--66. . . . . . . . . . . .00926 5--16. . . . . . . . . . . .00927 5--46. . . . . . . . . . . .00966 8--10. . . . . . . . . . . .01047 7--28. . . . . . . . . . . .01433--1 5--4. . . . . . . . .02485 5--31, 5--32. . . . . . . . . . . .02506--6 7--12. . . . . . . . .02513 5--60. . . . . . . . . . . .02607 8--16. . . . . . . . . . . .02634 5--68, 8--4. . . . . . . . . . . .02650 8--6. . . . . . . . . . . .02701 5--66. . . . . . . . . . . .02702 5--66. . . . . . . . . . . .02704 5--69, 8--6. . . . . . . . . . . .02705 8--6. . . . . . . . . . . .02706 8--6. . . . . . . . . . . .02707 8--6. . . . . . . . . . . .02708 8--6. . . . . . . . . . . .02709 8--6. . . . . . . . . . . .02710 8--6. . . . . . . . . . . .02711 8--6. . . . . . . . . . . .02712 5--34. . . . . . . . . . . .2724E--6518--A 9--6. . .02738 5--22, 5--24. . . . . . . . . . . .


02740 5--30. . . . . . . . . . . .02741 5--30. . . . . . . . . . . .02887 5--16, 5--18. . . . . . . . . . . .03158 5--14. . . . . . . . . . . .03160 5--20. . . . . . . . . . . .03233 5--14, 5--16. . . . . . . . . . . .03467A 5--34. . . . . . . . . .03498 5--31. . . . . . . . . . . .03549 5--64. . . . . . . . . . . .03556 5--64. . . . . . . . . . . .03711 7--20, 7--24. . . . . . . . . . . .03903 5--31, 5--32. . . . . . . . . . . .03907 5--31. . . . . . . . . . . .03908 5--31. . . . . . . . . . . .03909 5--31. . . . . . . . . . . .03912 5--31. . . . . . . . . . . .04081 5--64. . . . . . . . . . . .04084 5--31, 5--32. . . . . . . . . . . .04088 5--10. . . . . . . . . . . .04102 5--31. . . . . . . . . . . .04104 7--20, 7--24. . . . . . . . . . . .04106 5--26, 5--27. . . . . . . . . . . .04107 5--26, 5--27. . . . . . . . . . . .04118 7--20, 7--24. . . . . . . . . . . .04121 7--20, 7--24. . . . . . . . . . . .04123 7--20, 7--24. . . . . . . . . . . .04125 7--20, 7--24. . . . . . . . . . . .04133 7--22, 7--26. . . . . . . . . . . .04134 7--14, 7--16. . . . . . . . . . . .04148 7--14. . . . . . . . . . . .04430 5--54, 8--18. . . . . . . . . . . .04464 5--36, 8--17. . . . . . . . . . . .04481 8--17. . . . . . . . . . . .04483 8--18. . . . . . . . . . . .04743 5--43. . . . . . . . . . . .05416 5--48. . . . . . . . . . . .06418 5--36. . . . . . . . . . . .06507 5--26. . . . . . . . . . . .06532 5--24, 6--6. . . . . . . . . . . .06570 7--26. . . . . . . . . . . .06598 5--43, 5--46. . . . . . . . . . . .06750 5--72. . . . . . . . . . . .06777 5--56. . . . . . . . . . . .06997 9--13. . . . . . . . . . . .07056 5--58. . . . . . . . . . . .07120 5--16. . . . . . . . . . . .07175 5--18. . . . . . . . . . . .07189 5--14. . . . . . . . . . . .07250 5--22, 5--24. . . . . . . . . . . .07251 5--22, 5--24. . . . . . . . . . . .07252 5--22, 5--24. . . . . . . . . . . .07254 5--14. . . . . . . . . . . .07255 5--14. . . . . . . . . . . .07259 8--18. . . . . . . . . . . .07328 5--4, 9--13. . . . . . . . . . . .07330 5--4, 9--13. . . . . . . . . . . .07539 5--24, 6--6. . . . . . . . . . . .07562 5--30, 7--11. . . . . . . . . . . .07565 7--11. . . . . . . . . . . .07597 6--6. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-6


07598 6--6. . . . . . . . . . . .07602 6--6. . . . . . . . . . . .07705 5--4, 10--4. . . . . . . . . . . .07705 5--4. . . . . . . . . . . .07707 10--10. . . . . . . . . . . .07710 10--12. . . . . . . . . . . .07934 5--68. . . . . . . . . . . .08165 5--18. . . . . . . . . . . .08718 5--13. . . . . . . . . . . .08719 5--22. . . . . . . . . . . .08720 5--22. . . . . . . . . . . .08727 6--4. . . . . . . . . . . .08731 5--54. . . . . . . . . . . .08733 5--54. . . . . . . . . . . .08873 5--26. . . . . . . . . . . .09005 5--36. . . . . . . . . . . .09006 5--36. . . . . . . . . . . .09092--1 5--48. . . . . . . . .09385 5--58. . . . . . . . . . . .09600N 5--5. . . . . . . . . .09600P 5--5. . . . . . . . . .09718 5--44, 5--54. . . . . . . . . . . .09787 5--64. . . . . . . . . . . .09832 5--32, 5--41, 5--42. . . . . . . . . . . .09925 5--58. . . . . . . . . . . .10075 10--12. . . . . . . . . . . .10137 5--59. . . . . . . . . . . .10632--12 7--4, 7--5, 7--7, 7--8. . . . . . . .10632--14 7--14. . . . . . . .10632--20 7--6, 7--9. . . . . . . .10632--3 5--38. . . . . . . . .10712K 5--5. . . . . . . . . .10806 10--12, 10--18. . . . . . . . . . . .10827 5--64. . . . . . . . . . . .113765--ES2 9--4. . . . . .11399 7--20, 7--24. . . . . . . . . . . .11442--1 6--4, 6--6. . . . . . . . .11476 5--12. . . . . . . . . . . .11531 5--31, 5--32. . . . . . . . . . . .116106--ES10 10--8. . . . .116336--ES100 10--10. . . .116682--ES 10--12. . . . . . .116682--ES 9--10. . . . . . .118297--ES8 10--4. . . . . .11893 6--4. . . . . . . . . . . .11984 5--16, 5--22, 5--26, 5--27,. . . . . . . . . . . .

5--28, 5--4812044 5--22. . . . . . . . . . . .13027 5--38. . . . . . . . . . . .13028 7--28. . . . . . . . . . . .13038 5--32. . . . . . . . . . . .13041 7--14. . . . . . . . . . . .13045 5--34. . . . . . . . . . . .13046 5--34. . . . . . . . . . . .13047 5--34. . . . . . . . . . . .13048 6--4. . . . . . . . . . . .13049 6--4. . . . . . . . . . . .13054 5--4, 5--6. . . . . . . . . . . .13056 5--4, 5--6. . . . . . . . . . . .13061 5--70. . . . . . . . . . . .


13066 5--34. . . . . . . . . . . .13067 5--10. . . . . . . . . . . .13070 5--10. . . . . . . . . . . .13080 5--4, 5--38. . . . . . . . . . . .13081 5--4, 5--38. . . . . . . . . . . .13082 5--38. . . . . . . . . . . .13083 5--4, 5--38. . . . . . . . . . . .13090 7--28. . . . . . . . . . . .13097 5--64, 5--66. . . . . . . . . . . .13101 5--68, 5--69, 8--8. . . . . . . . . . . .13104 5--70, 8--16. . . . . . . . . . . .13105 5--44, 8--11. . . . . . . . . . . .13106 5--46, 8--13. . . . . . . . . . . .13108 5--74. . . . . . . . . . . .13109 5--74. . . . . . . . . . . .13110 5--74. . . . . . . . . . . .13113 5--74. . . . . . . . . . . .13114 5--6. . . . . . . . . . . .13115 5--74, 5--76. . . . . . . . . . . .13118 5--31. . . . . . . . . . . .13119 5--31. . . . . . . . . . . .13122 7--20. . . . . . . . . . . .13124 7--20, 7--24. . . . . . . . . . . .13127 7--20. . . . . . . . . . . .13130 5--78. . . . . . . . . . . .13131 5--8. . . . . . . . . . . .13132 5--38. . . . . . . . . . . .13138 5--8. . . . . . . . . . . .13139 5--78. . . . . . . . . . . .13144 5--38. . . . . . . . . . . .13151 5--46. . . . . . . . . . . .13156 5--46. . . . . . . . . . . .13157 5--46. . . . . . . . . . . .13164 7--16. . . . . . . . . . . .13165 5--4. . . . . . . . . . . .13165 5--6. . . . . . . . . . . .13166 5--4. . . . . . . . . . . .13166 5--6. . . . . . . . . . . .13170 5--46. . . . . . . . . . . .13172 5--4, 5--6. . . . . . . . . . . .13173 5--36. . . . . . . . . . . .13174 5--6. . . . . . . . . . . .13175 5--6. . . . . . . . . . . .13177 5--4, 5--6. . . . . . . . . . . .13178 5--4, 5--6. . . . . . . . . . . .13179 5--46. . . . . . . . . . . .13180 5--46. . . . . . . . . . . .13181 5--4, 5--6. . . . . . . . . . . .13184 5--6. . . . . . . . . . . .13195 5--78. . . . . . . . . . . .13199 5--43, 5--46, 5--56. . . . . . . . . . . .13202 5--46. . . . . . . . . . . .13203 7--28. . . . . . . . . . . .13205 5--40. . . . . . . . . . . .13211 5--40. . . . . . . . . . . .13212 5--40. . . . . . . . . . . .13226 7--28. . . . . . . . . . . .13228 7--28. . . . . . . . . . . .13229 7--28. . . . . . . . . . . .13233 7--28. . . . . . . . . . . .

CROSS REFERENCE

11-7365 MM173 (6--90)


13236 5--38. . . . . . . . . . . .13238 5--27. . . . . . . . . . . .13238 5--28. . . . . . . . . . . .13243 5--74, 5--76. . . . . . . . . . . .13244 5--38. . . . . . . . . . . .13248 5--32, 5--42, 5--64. . . . . . . . . . . .13249 5--44. . . . . . . . . . . .13251 5--26. . . . . . . . . . . .13253 5--26. . . . . . . . . . . .13259 5--60. . . . . . . . . . . .13268 5--38. . . . . . . . . . . .13269 5--38. . . . . . . . . . . .13270 5--4, 5--38. . . . . . . . . . . .13271 5--4, 5--38. . . . . . . . . . . .13279 5--8. . . . . . . . . . . .13280 5--5. . . . . . . . . . . .13281 5--5. . . . . . . . . . . .13282 5--5. . . . . . . . . . . .13283 5--5. . . . . . . . . . . .13290 5--43. . . . . . . . . . . .13291 5--38. . . . . . . . . . . .13292 5--38. . . . . . . . . . . .13293 5--4, 5--6. . . . . . . . . . . .13294 5--4, 5--6. . . . . . . . . . . .13295 5--4, 5--6. . . . . . . . . . . .13296 5--4, 5--6. . . . . . . . . . . .13297 5--38. . . . . . . . . . . .13301 5--4, 5--6, 5--38, 7--28. . . . . . . . . . . .13302 5--4, 5--38, 7--28. . . . . . . . . . . .13306 7--28. . . . . . . . . . . .13308 7--28. . . . . . . . . . . .13309 7--28. . . . . . . . . . . .13312 5--8. . . . . . . . . . . .13314 5--8. . . . . . . . . . . .13316 5--34. . . . . . . . . . . .13327 5--46. . . . . . . . . . . .13329 5--43. . . . . . . . . . . .13334 7--22, 7--26. . . . . . . . . . . .13335 5--38. . . . . . . . . . . .13360 5--64, 5--66. . . . . . . . . . . .13361 5--64, 5--66. . . . . . . . . . . .13362 5--64, 5--66. . . . . . . . . . . .13378 5--64, 5--66. . . . . . . . . . . .13387 5--8. . . . . . . . . . . .13392 5--64, 5--66. . . . . . . . . . . .13413 5--64, 5--66. . . . . . . . . . . .13468 5--4, 5--6. . . . . . . . . . . .13471 5--4, 5--6. . . . . . . . . . . .13472 5--4, 5--6. . . . . . . . . . . .13476 5--4, 5--6. . . . . . . . . . . .13493 5--38. . . . . . . . . . . .13513 5--64, 5--66. . . . . . . . . . . .13515 5--13. . . . . . . . . . . .13516 5--22. . . . . . . . . . . .13525 5--22. . . . . . . . . . . .13532 5--41. . . . . . . . . . . .13534 5--46. . . . . . . . . . . .13540 5--64, 5--66. . . . . . . . . . . .13554 5--64, 5--66. . . . . . . . . . . .13555 5--41. . . . . . . . . . . .


13559 5--36. . . . . . . . . . . .13572 5--10. . . . . . . . . . . .13585 7--14. . . . . . . . . . . .13586 7--14. . . . . . . . . . . .13590 7--14. . . . . . . . . . . .13594 7--14. . . . . . . . . . . .13596 7--14. . . . . . . . . . . .13597 7--14. . . . . . . . . . . .13598 5--10. . . . . . . . . . . .13601 5--34. . . . . . . . . . . .13602 5--10. . . . . . . . . . . .13689 7--28. . . . . . . . . . . .13698 5--31, 5--32. . . . . . . . . . . .13734 7--30. . . . . . . . . . . .13739 5--29. . . . . . . . . . . .13743 7--28. . . . . . . . . . . .13746 5--8. . . . . . . . . . . .13747 5--6. . . . . . . . . . . .13751 5--78. . . . . . . . . . . .13756 5--78. . . . . . . . . . . .13757 7--16. . . . . . . . . . . .13778 5--27, 5--28. . . . . . . . . . . .13779 5--10. . . . . . . . . . . .13788 5--72. . . . . . . . . . . .13789 5--6. . . . . . . . . . . .13791 5--72. . . . . . . . . . . .13792 5--8. . . . . . . . . . . .13807 5--62. . . . . . . . . . . .13818 5--62. . . . . . . . . . . .13828 5--6. . . . . . . . . . . .13864 5--60. . . . . . . . . . . .13879 5--58. . . . . . . . . . . .13891 8--16. . . . . . . . . . . .13893 8--16. . . . . . . . . . . .13894 8--16. . . . . . . . . . . .13895 8--16. . . . . . . . . . . .13896 8--16. . . . . . . . . . . .13898 8--16. . . . . . . . . . . .13899 8--16. . . . . . . . . . . .13902 8--16. . . . . . . . . . . .13903 8--16. . . . . . . . . . . .13904 8--16. . . . . . . . . . . .13907 8--16. . . . . . . . . . . .13909 8--16. . . . . . . . . . . .13924 8--18. . . . . . . . . . . .13932 8--16. . . . . . . . . . . .13945 8--16. . . . . . . . . . . .13947 8--16. . . . . . . . . . . .13948 8--16. . . . . . . . . . . .13959 5--48. . . . . . . . . . . .13966 8--8. . . . . . . . . . . .13970 5--4. . . . . . . . . . . .13973 5--4. . . . . . . . . . . .13974 5--4. . . . . . . . . . . .13988 5--26. . . . . . . . . . . .13989 8--8. . . . . . . . . . . .14131 5--26, 5--27, 5--28. . . . . . . . . . . .14138A 5--8. . . . . . . . . .14242 5--54. . . . . . . . . . . .14331 5--48. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-8


14432 5--29, 5--30. . . . . . . . . . . .14595--1 5--64, 5--66. . . . . . . . .14601 5--22, 5--24, 6--6. . . . . . . . . . . .14605 5--64, 5--66. . . . . . . . . . . .14700--4 5--56. . . . . . . . .15066 7--14, 7--16. . . . . . . . . . . .15280--1 5--16. . . . . . . . .15280--3 5--66. . . . . . . . .15555--1 5--24. . . . . . . . .16081 5--29, 5--54. . . . . . . . . . . .16456 5--36. . . . . . . . . . . .16465 5--74. . . . . . . . . . . .16472 5--18. . . . . . . . . . . .16694 8--11, 8--12. . . . . . . . . . . .16695 8--11, 8--12, 8--13, 8--14. . . . . . . . . . . .16735 5--18, 5--20. . . . . . . . . . . .16736 5--66. . . . . . . . . . . .16738 5--22, 5--24. . . . . . . . . . . .16805 5--13. . . . . . . . . . . .16869 7--31. . . . . . . . . . . .16931 5--14. . . . . . . . . . . .17409 7--24. . . . . . . . . . . .17414 5--16, 5--18. . . . . . . . . . . .17759 5--13. . . . . . . . . . . .17980 5--34, 5--70. . . . . . . . . . . .19071 5--66. . . . . . . . . . . .19073 5--20. . . . . . . . . . . .19074 5--66. . . . . . . . . . . .19100 5--20. . . . . . . . . . . .19106 5--20. . . . . . . . . . . .19171 5--28. . . . . . . . . . . .19200 5--18. . . . . . . . . . . .19205 5--4, 10--12. . . . . . . . . . . .19252 5--20. . . . . . . . . . . .19531 5--20. . . . . . . . . . . .19580 5--6, 5--64. . . . . . . . . . . .19583 5--54. . . . . . . . . . . .19630 5--76. . . . . . . . . . . .19676 5--32. . . . . . . . . . . .19689 5--18. . . . . . . . . . . .19768 5--58. . . . . . . . . . . .20050 5--44. . . . . . . . . . . .20160 5--66. . . . . . . . . . . .20343 7--20, 7--24. . . . . . . . . . . .20536--1 6--4. . . . . . . . .20567 5--38. . . . . . . . . . . .22297 5--72. . . . . . . . . . . .22308 6--4. . . . . . . . . . . .22383 5--26, 5--27. . . . . . . . . . . .22465 5--40. . . . . . . . . . . .22794 7--4, 7--7. . . . . . . . . . . .23498 5--34. . . . . . . . . . . .23542 5--34. . . . . . . . . . . .23546 5--44. . . . . . . . . . . .23999--3 5--44. . . . . . . . .24012 5--41, 5--42. . . . . . . . . . . .24013 5--18. . . . . . . . . . . .24047 6--4. . . . . . . . . . . .24339 5--52, 5--54. . . . . . . . . . . .24928 6--4. . . . . . . . . . . .


24928--1 6--4. . . . . . . . .24929 5--16. . . . . . . . . . . .24976 5--18. . . . . . . . . . . .24989 5--52. . . . . . . . . . . .25312 7--12. . . . . . . . . . . .26395--1 5--36, 5--50, 6--4, 7--18. . . . . . . . .26426 5--18. . . . . . . . . . . .26496 6--4. . . . . . . . . . . .27048 6--4. . . . . . . . . . . .27184 7--26. . . . . . . . . . . .27800 5--46, 8--14. . . . . . . . . . . .28296 5--22. . . . . . . . . . . .28808 5--44, 8--12. . . . . . . . . . . .28835 8--12, 8--13, 8--14. . . . . . . . . . . .29087 5--64, 5--66. . . . . . . . . . . .29192 7--4, 7--7. . . . . . . . . . . .29233 5--10, 5--31, 5--32. . . . . . . . . . . .29499 6--4. . . . . . . . . . . .29570 5--34, 5--70. . . . . . . . . . . .30296 5--18. . . . . . . . . . . .30305 5--24. . . . . . . . . . . .30306 5--18. . . . . . . . . . . .30312 5--24, 6--6. . . . . . . . . . . .30316 5--18. . . . . . . . . . . .30318 5--24, 6--6. . . . . . . . . . . .30320 5--24, 6--6. . . . . . . . . . . .30321 5--24. . . . . . . . . . . .30322 6--6. . . . . . . . . . . .30324 5--24, 6--6. . . . . . . . . . . .30325 5--24. . . . . . . . . . . .30326 6--6. . . . . . . . . . . .30327 10--4. . . . . . . . . . . .30348 5--32. . . . . . . . . . . .30354 5--32. . . . . . . . . . . .30434 5--20. . . . . . . . . . . .30451 5--24, 6--6. . . . . . . . . . . .30458 5--14. . . . . . . . . . . .30463 5--18. . . . . . . . . . . .31174 5--74. . . . . . . . . . . .31182 5--10, 5--38. . . . . . . . . . . .31183 5--10, 5--38. . . . . . . . . . . .31249 5--64. . . . . . . . . . . .31354 8--12, 8--14. . . . . . . . . . . .31374 8--14. . . . . . . . . . . .31375 8--14. . . . . . . . . . . .31380 8--14. . . . . . . . . . . .31381 8--12. . . . . . . . . . . .31383 8--14. . . . . . . . . . . .31486 5--30. . . . . . . . . . . .31490 5--32. . . . . . . . . . . .31491 5--20. . . . . . . . . . . .31498 5--6. . . . . . . . . . . .31500 7--30. . . . . . . . . . . .31506 5--42. . . . . . . . . . . .31507 7--24. . . . . . . . . . . .31511 5--30. . . . . . . . . . . .31515 5--30. . . . . . . . . . . .31516 5--18. . . . . . . . . . . .31517 5--32. . . . . . . . . . . .31518 5--32. . . . . . . . . . . .

CROSS REFERENCE

11-9365 MM173 (6--90)


31526 5--14. . . . . . . . . . . .31528 5--62. . . . . . . . . . . .31529 5--8. . . . . . . . . . . .31534 5--14. . . . . . . . . . . .31537 8--4. . . . . . . . . . . .31539 5--66. . . . . . . . . . . .31541 5--32. . . . . . . . . . . .31542 5--24, 6--6. . . . . . . . . . . .31543 5--18, 6--6, 7--24. . . . . . . . . . . .31550 5--24. . . . . . . . . . . .31560 5--78. . . . . . . . . . . .31561 5--78. . . . . . . . . . . .31563 5--74, 5--76. . . . . . . . . . . .31576 5--8. . . . . . . . . . . .31581 5--10. . . . . . . . . . . .31585 5--10. . . . . . . . . . . .31586 5--10. . . . . . . . . . . .31587 5--10. . . . . . . . . . . .31588 5--34. . . . . . . . . . . .31602 5--74. . . . . . . . . . . .31602 5--76. . . . . . . . . . . .31613 5--72. . . . . . . . . . . .31640 5--42. . . . . . . . . . . .31705 5--52. . . . . . . . . . . .31713 5--34. . . . . . . . . . . .31714 5--76. . . . . . . . . . . .31718 5--78. . . . . . . . . . . .31719 5--76. . . . . . . . . . . .31720 5--76. . . . . . . . . . . .31721 5--76. . . . . . . . . . . .31722 5--76. . . . . . . . . . . .31724 5--76. . . . . . . . . . . .31725 5--76. . . . . . . . . . . .31728 5--24, 6--6. . . . . . . . . . . .31745 5--4. . . . . . . . . . . .31746 5--4. . . . . . . . . . . .31754 7--24. . . . . . . . . . . .31962 5--8. . . . . . . . . . . .31963 5--8. . . . . . . . . . . .31964 5--8. . . . . . . . . . . .31965 5--8, 5--58, 7--4, 7--5, 7--6,. . . . . . . . . . . .

7--7, 7--8, 7--9, 7--1831966 5--8. . . . . . . . . . . .32126 5--54. . . . . . . . . . . .32270 5--8. . . . . . . . . . . .32397--1 5--4. . . . . . . . .32418 7--20, 7--24. . . . . . . . . . . .32486 5--54. . . . . . . . . . . .32493 5--20. . . . . . . . . . . .32495 5--36. . . . . . . . . . . .32523 5--38. . . . . . . . . . . .32827 5--40. . . . . . . . . . . .32839 5--41. . . . . . . . . . . .32840 5--41. . . . . . . . . . . .32841 5--41. . . . . . . . . . . .32985 5--38. . . . . . . . . . . .32987 5--54. . . . . . . . . . . .33308 7--20, 7--24. . . . . . . . . . . .33329 5--41, 5--42. . . . . . . . . . . .33330 5--41. . . . . . . . . . . .


33333 5--41, 5--42. . . . . . . . . . . .33555 6--4. . . . . . . . . . . .33579 8--9. . . . . . . . . . . .33580 8--9. . . . . . . . . . . .33694 8--9. . . . . . . . . . . .33778 5--16. . . . . . . . . . . .33826 5--16. . . . . . . . . . . .33864 9--12. . . . . . . . . . . .34096 5--66. . . . . . . . . . . .34174 8--11, 8--13. . . . . . . . . . . .34175 8--12. . . . . . . . . . . .34176 8--11, 8--12, 8--13. . . . . . . . . . . .34177 8--13. . . . . . . . . . . .34251 5--12. . . . . . . . . . . .34252 5--12. . . . . . . . . . . .34292 5--48. . . . . . . . . . . .34323 5--34. . . . . . . . . . . .34329 5--44. . . . . . . . . . . .34330 5--54, 5--56. . . . . . . . . . . .34344 10--8. . . . . . . . . . . .34366 5--74, 5--76. . . . . . . . . . . .34375 5--6. . . . . . . . . . . .34380 5--74, 5--76. . . . . . . . . . . .34805--S8 10--8, 10--12. . . . . . . .34810 5--58. . . . . . . . . . . .34813 5--58. . . . . . . . . . . .34816 5--8. . . . . . . . . . . .34868 5--38. . . . . . . . . . . .34877 5--20. . . . . . . . . . . .34898 5--22. . . . . . . . . . . .35033 5--68, 5--69. . . . . . . . . . . .353055--S7 10--6. . . . . . .35688 5--36. . . . . . . . . . . .36253 10--18. . . . . . . . . . . .36254 10--18. . . . . . . . . . . .36257 10--10. . . . . . . . . . . .36258 10--15. . . . . . . . . . . .36259 10--10. . . . . . . . . . . .36262 10--10. . . . . . . . . . . .36263 10--6. . . . . . . . . . . .36264 10--6. . . . . . . . . . . .36265 10--4, 10--6. . . . . . . . . . . .36267 10--6. . . . . . . . . . . .36268 10--6. . . . . . . . . . . .36272 10--6. . . . . . . . . . . .36273 10--6. . . . . . . . . . . .36274 10--6. . . . . . . . . . . .36275 10--6. . . . . . . . . . . .36276 10--6. . . . . . . . . . . .36277 10--6. . . . . . . . . . . .36278 10--6. . . . . . . . . . . .36279 10--4. . . . . . . . . . . .36281 10--4. . . . . . . . . . . .36297 10--4. . . . . . . . . . . .36298 10--4. . . . . . . . . . . .36300 10--4. . . . . . . . . . . .36303 10--4. . . . . . . . . . . .36306 10--4. . . . . . . . . . . .36307 10--4. . . . . . . . . . . .36315 10--4. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-10


36317 10--4. . . . . . . . . . . .36318 10--4. . . . . . . . . . . .36319 10--4. . . . . . . . . . . .36321 10--4. . . . . . . . . . . .36322 10--10. . . . . . . . . . . .36324 10--4. . . . . . . . . . . .36325 10--4. . . . . . . . . . . .36330 10--4. . . . . . . . . . . .36331 10--4. . . . . . . . . . . .36332 10--15. . . . . . . . . . . .36333 10--15. . . . . . . . . . . .36337 10--15. . . . . . . . . . . .36338 10--15. . . . . . . . . . . .36339 10--15. . . . . . . . . . . .36340 10--8. . . . . . . . . . . .36341 10--8. . . . . . . . . . . .36342 10--8. . . . . . . . . . . .36343 10--8. . . . . . . . . . . .36344 10--8. . . . . . . . . . . .36345 10--8. . . . . . . . . . . .36348 10--8. . . . . . . . . . . .36349 10--8. . . . . . . . . . . .36372 10--8. . . . . . . . . . . .36373 10--12. . . . . . . . . . . .36373 10--8. . . . . . . . . . . .36374 10--8. . . . . . . . . . . .36375 10--8. . . . . . . . . . . .36381 10--8. . . . . . . . . . . .36382 10--8. . . . . . . . . . . .36383 10--8. . . . . . . . . . . .36384 10--8. . . . . . . . . . . .36389 10--8. . . . . . . . . . . .36390 10--8. . . . . . . . . . . .36402 10--8. . . . . . . . . . . .36405 10--8. . . . . . . . . . . .36406 10--8. . . . . . . . . . . .36407 10--8. . . . . . . . . . . .36408 10--8. . . . . . . . . . . .36409 10--8. . . . . . . . . . . .36410 10--10. . . . . . . . . . . .36411 10--10. . . . . . . . . . . .36412 10--10. . . . . . . . . . . .36413 10--10. . . . . . . . . . . .36414 10--10. . . . . . . . . . . .36415 10--10. . . . . . . . . . . .36416 10--10. . . . . . . . . . . .36418 10--10. . . . . . . . . . . .36419 10--10. . . . . . . . . . . .36421 10--10. . . . . . . . . . . .36422 10--10. . . . . . . . . . . .36423 10--10. . . . . . . . . . . .36424 10--10. . . . . . . . . . . .36429 10--10. . . . . . . . . . . .36430 10--10. . . . . . . . . . . .36431 10--10, 10--12, 10--16. . . . . . . . . . . .36432 10--10. . . . . . . . . . . .36433 10--10. . . . . . . . . . . .36445 10--10. . . . . . . . . . . .36450 10--10. . . . . . . . . . . .36451 10--10. . . . . . . . . . . .


36452 10--10. . . . . . . . . . . .36453 10--10. . . . . . . . . . . .36454 10--10. . . . . . . . . . . .36463 10--10. . . . . . . . . . . .36467 10--10. . . . . . . . . . . .36469 10--10. . . . . . . . . . . .36483 10--10. . . . . . . . . . . .36493 10--10. . . . . . . . . . . .36590 10--10. . . . . . . . . . . .36591 10--19. . . . . . . . . . . .36630 10--19. . . . . . . . . . . .36646 10--19. . . . . . . . . . . .36658 5--38. . . . . . . . . . . .36661 5--38. . . . . . . . . . . .36663 5--38. . . . . . . . . . . .36665 5--38. . . . . . . . . . . .36666 5--38. . . . . . . . . . . .36748 10--12. . . . . . . . . . . .36758 5--43. . . . . . . . . . . .36764 10--12. . . . . . . . . . . .36765 10--12. . . . . . . . . . . .36776 10--12. . . . . . . . . . . .36780 10--12. . . . . . . . . . . .36867 10--12. . . . . . . . . . . .36881 10--12. . . . . . . . . . . .36904 10--12. . . . . . . . . . . .36923 10--12. . . . . . . . . . . .36924 10--12. . . . . . . . . . . .37031 5--38. . . . . . . . . . . .37053 10--12. . . . . . . . . . . .37083--1 7--14. . . . . . . . .37098 10--12. . . . . . . . . . . .37099 10--12. . . . . . . . . . . .37127 10--12. . . . . . . . . . . .37157 10--12. . . . . . . . . . . .37181 10--10, 10--16. . . . . . . . . . . .37188 10--16. . . . . . . . . . . .37189 10--16. . . . . . . . . . . .37193 10--16. . . . . . . . . . . .37194 10--14. . . . . . . . . . . .37195 10--14. . . . . . . . . . . .37196 10--14. . . . . . . . . . . .37198 10--14. . . . . . . . . . . .37199 10--14. . . . . . . . . . . .37303 9--10. . . . . . . . . . . .37306 9--8, 10--8. . . . . . . . . . . .37307 9--8, 10--8. . . . . . . . . . . .37308 9--6. . . . . . . . . . . .37309 9--6. . . . . . . . . . . .37312 9--5. . . . . . . . . . . .37315 9--8. . . . . . . . . . . .37316 9--8, 10--8. . . . . . . . . . . .37317 9--8, 10--8. . . . . . . . . . . .37321 9--5, 10--10. . . . . . . . . . . .37325 9--12. . . . . . . . . . . .37326 9--10. . . . . . . . . . . .37327 9--12, 10--16. . . . . . . . . . . .37328 9--13. . . . . . . . . . . .37330 9--5. . . . . . . . . . . .37332 9--14. . . . . . . . . . . .

CROSS REFERENCE

11-11365 MM173 (6--90)


37333 9--4. . . . . . . . . . . .37334 9--14. . . . . . . . . . . .37335 9--9. . . . . . . . . . . .37337 9--8, 10--8. . . . . . . . . . . .37338 9--8. . . . . . . . . . . .37340 9--6. . . . . . . . . . . .37341 9--10. . . . . . . . . . . .37342 9--4. . . . . . . . . . . .37343 9--5. . . . . . . . . . . .37344 9--10. . . . . . . . . . . .37351 9--4. . . . . . . . . . . .37354 9--10. . . . . . . . . . . .37358 9--6. . . . . . . . . . . .37368 9--6. . . . . . . . . . . .37403 9--10. . . . . . . . . . . .37457 8--4, 8--6. . . . . . . . . . . .37616 8--9. . . . . . . . . . . .37617 8--13. . . . . . . . . . . .37689 9--5. . . . . . . . . . . .37693 9--6, 10--8. . . . . . . . . . . .37694 10--8. . . . . . . . . . . .37694 9--8. . . . . . . . . . . .37719 9--5. . . . . . . . . . . .37756 8--9. . . . . . . . . . . .37844 9--10. . . . . . . . . . . .38242 9--8, 10--8. . . . . . . . . . . .38243 9--9. . . . . . . . . . . .38245 5--4, 9--10. . . . . . . . . . . .38246 9--4. . . . . . . . . . . .38250 9--6. . . . . . . . . . . .39025 10--17. . . . . . . . . . . .39026 10--17. . . . . . . . . . . .39035 10--17. . . . . . . . . . . .39038 10--17. . . . . . . . . . . .39040 10--17. . . . . . . . . . . .39041 10--17. . . . . . . . . . . .39042 10--17. . . . . . . . . . . .39043 10--17. . . . . . . . . . . .39044 10--17. . . . . . . . . . . .39045 10--17. . . . . . . . . . . .39046 5--4, 10--17. . . . . . . . . . . .39047 10--15. . . . . . . . . . . .39210 5--44, 5--68, 5--69, 5--70. . . . . . . . . . . .39283 5--14. . . . . . . . . . . .39284 5--30. . . . . . . . . . . .39302 5--50. . . . . . . . . . . .39311 5--24, 6--6. . . . . . . . . . . .39319 5--38. . . . . . . . . . . .39328 5--64, 5--66. . . . . . . . . . . .39330 5--16, 5--66. . . . . . . . . . . .39349 5--18. . . . . . . . . . . .39350 5--54. . . . . . . . . . . .39396 5--44. . . . . . . . . . . .39527 5--36, 8--13, 8--14. . . . . . . . . . . .39780 5--24. . . . . . . . . . . .39811 5--38. . . . . . . . . . . .39900 5--54. . . . . . . . . . . .39923 5--38. . . . . . . . . . . .40362 5--72. . . . . . . . . . . .40585 5--28. . . . . . . . . . . .


40586 5--24. . . . . . . . . . . .40607 5--38. . . . . . . . . . . .40625 5--18. . . . . . . . . . . .40678 5--8, 5--38. . . . . . . . . . . .40727 5--46. . . . . . . . . . . .40823 5--22. . . . . . . . . . . .41016 5--68, 5--69. . . . . . . . . . . .41112 5--52. . . . . . . . . . . .41136 5--34. . . . . . . . . . . .41361 5--16, 5--20. . . . . . . . . . . .42216 5--30. . . . . . . . . . . .42260 5--29, 5--32, 5--54, 5--68,. . . . . . . . . . . .

5--69, 5--7043242 5--22, 6--4, 7--24. . . . . . . . . . . .43454 5--31, 5--32, 5--38. . . . . . . . . . . .43844 5--26, 5--27, 5--28. . . . . . . . . . . .43896 5--50. . . . . . . . . . . .43949 5--58. . . . . . . . . . . .44561 5--13. . . . . . . . . . . .44681 7--4, 7--5, 7--6. . . . . . . . . . . .44681--1 7--4, 7--5, 7--6. . . . . . . . .44681--2 7--4, 7--5, 7--6. . . . . . . . .44847 5--8. . . . . . . . . . . .44868 5--34, 5--70. . . . . . . . . . . .44869 5--34, 5--46, 5--69, 5--70. . . . . . . . . . . .44961 7--20. . . . . . . . . . . .45181 5--64. . . . . . . . . . . .45261 5--22. . . . . . . . . . . .45482 5--34. . . . . . . . . . . .45622 8--9. . . . . . . . . . . .45623 8--9. . . . . . . . . . . .45628 8--11, 8--12, 8--13, 8--14. . . . . . . . . . . .45770--8 5--4, 9--13. . . . . . . . .45779 7--4, 7--5, 7--6, 7--7, 7--8, 7--9. . . . . . . . . . . .45780 5--6. . . . . . . . . . . .45786 5--52, 5--53. . . . . . . . . . . .46231 6--4. . . . . . . . . . . .46236 5--22, 5--26, 5--40, 7--4, 7--5,. . . . . . . . . . . .

7--7, 7--846307 5--43. . . . . . . . . . . .46328 5--64, 5--66. . . . . . . . . . . .46481 5--30, 5--31, 5--32. . . . . . . . . . . .46563 5--10. . . . . . . . . . . .46611 6--4. . . . . . . . . . . .46938 7--12. . . . . . . . . . . .47010--1 5--56. . . . . . . . .47010--2 5--56. . . . . . . . .47010--3 5--56. . . . . . . . .47010--4 5--56. . . . . . . . .47010--6 5--56. . . . . . . . .47010--7 5--56. . . . . . . . .47037 5--4. . . . . . . . . . . .47167 7--20, 7--24. . . . . . . . . . . .47178 5--44. . . . . . . . . . . .47178--6 6--4. . . . . . . . .47178--16 7--4, 7--5, 7--6. . . . . . . .47192 6--4. . . . . . . . . . . .47313A 5--22. . . . . . . . . .47473 5--26, 5--27, 5--28. . . . . . . . . . . .47524 5--68, 5--69. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-12


47649 8--11. . . . . . . . . . . .47701 7--24. . . . . . . . . . . .47719 5--54. . . . . . . . . . . .47753 5--6. . . . . . . . . . . .47826 5--29. . . . . . . . . . . .47933 5--16. . . . . . . . . . . .47989 5--41. . . . . . . . . . . .48252 5--58. . . . . . . . . . . .48253 5--26. . . . . . . . . . . .48253 5--27. . . . . . . . . . . .48258 7--4, 7--7. . . . . . . . . . . .48267 5--26, 5--27, 5--28. . . . . . . . . . . .48655 5--31. . . . . . . . . . . .48663 5--54, 8--9. . . . . . . . . . . .49225 5--54. . . . . . . . . . . .49263 5--26, 5--29, 5--54, 5--56,. . . . . . . . . . . .

5--72, 6--649266 5--24, 5--36, 5--44, 6--4. . . . . . . . . . . .49287 5--72. . . . . . . . . . . .49681 5--64, 5--66. . . . . . . . . . . .49957--1 5--74, 5--76. . . . . . . . .50332--1 5--22, 5--24, 6--6. . . . . . . . .50332--2 5--24, 6--6. . . . . . . . .50352 9--6. . . . . . . . . . . .50388 5--13. . . . . . . . . . . .50470 7--4, 7--7. . . . . . . . . . . .51059 5--46. . . . . . . . . . . .51109 5--48. . . . . . . . . . . .51176 5--16, 5--20. . . . . . . . . . . .51225 5--22. . . . . . . . . . . .51304--1 5--12. . . . . . . . .51305 5--31. . . . . . . . . . . .51317 5--46. . . . . . . . . . . .51355 5--53, 7--13. . . . . . . . . . . .51357 5--53. . . . . . . . . . . .51360 5--53. . . . . . . . . . . .51361 5--53. . . . . . . . . . . .51362 5--53. . . . . . . . . . . .51372 7--28. . . . . . . . . . . .51406 7--14, 7--20, 7--24. . . . . . . . . . . .51416 7--14, 7--20, 7--24. . . . . . . . . . . .51448 5--46. . . . . . . . . . . .51449 5--46. . . . . . . . . . . .51483 5--48. . . . . . . . . . . .51531 5--66. . . . . . . . . . . .51534 5--40. . . . . . . . . . . .51545 5--50. . . . . . . . . . . .51560--3 5--29, 5--30. . . . . . . . .51562 5--50. . . . . . . . . . . .51564 5--16. . . . . . . . . . . .51705 7--13. . . . . . . . . . . .51711 7--13. . . . . . . . . . . .51805 5--16, 5--18. . . . . . . . . . . .51813 5--56. . . . . . . . . . . .51839 6--4, 6--6, 7--20, 9--12. . . . . . . . . . . .52033 5--29. . . . . . . . . . . .52388 5--56. . . . . . . . . . . .52510 5--53. . . . . . . . . . . .52775 5--53, 7--13. . . . . . . . . . . .53386 5--16. . . . . . . . . . . .


53400--1 6--4. . . . . . . . .53400--4 6--4. . . . . . . . .53531--2 5--16. . . . . . . . .53963A 5--38, 5--40. . . . . . . . . .54009 7--28. . . . . . . . . . . .54012 7--28. . . . . . . . . . . .54121 5--38. . . . . . . . . . . .54230 5--26, 5--27. . . . . . . . . . . .54231 5--26. . . . . . . . . . . .54274 5--32, 5--34, 5--41, 5--42, 5--64. . . . . . . . . . . .54275A 5--34. . . . . . . . . .54333 5--18, 5--29, 5--30, 5--72, 6--4. . . . . . . . . . . .54338--7 5--26, 5--27. . . . . . . . .54527 5--34, 5--70. . . . . . . . . . . .54528 5--34, 5--70. . . . . . . . . . . .54745 5--22. . . . . . . . . . . .54911--5 5--16. . . . . . . . .54911--7 5--16. . . . . . . . .54912--8 5--22. . . . . . . . .54911--10 5--13. . . . . . . .54911--11 5--16. . . . . . . . .54911--15 5--16. . . . . . . .54911--16 5--16. . . . . . . .54911--16 5--20. . . . . . . .54911--20 9--4. . . . . . . .54911--21 9--4. . . . . . . .54911--22 9--4. . . . . . . .54911--23 9--4. . . . . . . .54911--24 5--4, 9--6. . . . . . . .54911--25 5--16. . . . . . . .54911--25 5--18. . . . . . . .54911--25 9--12. . . . . . . .54911--27 9--10. . . . . . . .54911--28 5--16. . . . . . . .54911--30 5--16. . . . . . . .54911--31 5--16. . . . . . . .54911--32 5--16, 5--32. . . . . . . .54914 5--14, 5--16. . . . . . . . . . . .54928 5--16. . . . . . . . . . . .54930 6--4, 6--6. . . . . . . . . . . .54959 5--14, 5--16. . . . . . . . . . . .55130 5--38. . . . . . . . . . . .55258 5--58. . . . . . . . . . . .55271 5--58. . . . . . . . . . . .55272 5--40, 7--5, 7--6, 7--8, 7--9. . . . . . . . . . . .55290 7--4, 7--5, 7--6. . . . . . . . . . . .55291 7--4, 7--5, 7--6. . . . . . . . . . . .55297 7--4, 7--5, 7--6. . . . . . . . . . . .55557 5--58. . . . . . . . . . . .55586 5--36, 5--46, 5--54, 5--70. . . . . . . . . . . .55589 5--22. . . . . . . . . . . .55619 5--29, 5--30. . . . . . . . . . . .55633 6--4. . . . . . . . . . . .55685 5--56. . . . . . . . . . . .55686 5--68, 5--69. . . . . . . . . . . .55697 5--74, 5--76. . . . . . . . . . . .55740 5--4, 5--29, 5--30. . . . . . . . . . . .55905 8--4. . . . . . . . . . . .55906 8--4, 8--6. . . . . . . . . . . .55918 8--4. . . . . . . . . . . .

CROSS REFERENCE

11-13365 MM173 (6--90)


55920 8--4. . . . . . . . . . . .55922 8--4. . . . . . . . . . . .55922 8--6. . . . . . . . . . . .55929 8--4, 8--6. . . . . . . . . . . .55930 8--4, 8--6. . . . . . . . . . . .55931 8--4, 8--6. . . . . . . . . . . .55932 8--4, 8--6. . . . . . . . . . . .55933 8--4. . . . . . . . . . . .55937 8--4, 8--6. . . . . . . . . . . .55939 8--4, 8--6. . . . . . . . . . . .55941 8--4. . . . . . . . . . . .55975 6--6. . . . . . . . . . . .55998 6--4, 6--6. . . . . . . . . . . .56690 5--56. . . . . . . . . . . .56692 5--68, 5--69, 5--72. . . . . . . . . . . .56799 5--38. . . . . . . . . . . .56820 5--70. . . . . . . . . . . .56855 5--66. . . . . . . . . . . .56976A 6--4. . . . . . . . . .56980 5--44. . . . . . . . . . . .57048 5--20. . . . . . . . . . . .57051 8--4. . . . . . . . . . . .57064 8--8. . . . . . . . . . . .57152 8--15. . . . . . . . . . . .57153 5--74, 5--76. . . . . . . . . . . .57154 8--15. . . . . . . . . . . .57155 8--15. . . . . . . . . . . .57156 8--15. . . . . . . . . . . .57186 8--16. . . . . . . . . . . .57210 8--4, 8--6. . . . . . . . . . . .57221 5--74. . . . . . . . . . . .57222 5--74. . . . . . . . . . . .57230 5--22. . . . . . . . . . . .57275 5--52. . . . . . . . . . . .57277 5--52. . . . . . . . . . . .57278 5--52. . . . . . . . . . . .57297 6--4. . . . . . . . . . . .57298 5--10. . . . . . . . . . . .57345 5--59. . . . . . . . . . . .57392 5--22. . . . . . . . . . . .57511 5--4, 5--38. . . . . . . . . . . .57518 5--4. . . . . . . . . . . .57519 5--4. . . . . . . . . . . .57526 7--14. . . . . . . . . . . .57528 7--20, 7--24. . . . . . . . . . . .57531 7--20, 7--24. . . . . . . . . . . .57532 7--20, 7--24. . . . . . . . . . . .57533 7--20. . . . . . . . . . . .57534 7--14. . . . . . . . . . . .57535 7--18. . . . . . . . . . . .57536 7--18. . . . . . . . . . . .57537 7--18. . . . . . . . . . . .57544 6--4. . . . . . . . . . . .57548 5--16. . . . . . . . . . . .57549 5--16. . . . . . . . . . . .57561 5--54. . . . . . . . . . . .57563 5--10. . . . . . . . . . . .57564 5--10. . . . . . . . . . . .57565 5--52. . . . . . . . . . . .57567 5--52. . . . . . . . . . . .


57569 5--34. . . . . . . . . . . .57570 5--6. . . . . . . . . . . .57575 5--74, 5--76. . . . . . . . . . . .57577 5--54. . . . . . . . . . . .57582 5--74, 5--76. . . . . . . . . . . .57588 5--6. . . . . . . . . . . .57594 5--6. . . . . . . . . . . .57598 7--16. . . . . . . . . . . .57604 7--18. . . . . . . . . . . .57608 7--18. . . . . . . . . . . .57625 7--14. . . . . . . . . . . .57631 7--16. . . . . . . . . . . .57633 7--16. . . . . . . . . . . .57634 7--14. . . . . . . . . . . .57636 7--14. . . . . . . . . . . .57637 7--16. . . . . . . . . . . .57639 7--14. . . . . . . . . . . .57640 7--16. . . . . . . . . . . .57641 7--16. . . . . . . . . . . .57642 7--16. . . . . . . . . . . .57643 7--14, 7--16. . . . . . . . . . . .57644 7--16. . . . . . . . . . . .57646 7--16. . . . . . . . . . . .57647 7--16. . . . . . . . . . . .57648 7--14. . . . . . . . . . . .57649 7--16. . . . . . . . . . . .57651 7--14. . . . . . . . . . . .57652 7--14. . . . . . . . . . . .57653 7--14. . . . . . . . . . . .57654 7--14. . . . . . . . . . . .57662 7--16. . . . . . . . . . . .57664 7--14. . . . . . . . . . . .57667 7--16. . . . . . . . . . . .57670 7--14. . . . . . . . . . . .57674 7--14. . . . . . . . . . . .57676 5--56. . . . . . . . . . . .57677 7--14. . . . . . . . . . . .57678 7--16. . . . . . . . . . . .57686 5--29. . . . . . . . . . . .57703 7--30. . . . . . . . . . . .57710 7--30. . . . . . . . . . . .57740 7--4, 7--5, 7--6, 7--7, 7--8, 7--9. . . . . . . . . . . .57741 5--46. . . . . . . . . . . .57742 5--46. . . . . . . . . . . .57743 5--46. . . . . . . . . . . .57744 5--46. . . . . . . . . . . .57751 5--58. . . . . . . . . . . .57751 7--22. . . . . . . . . . . .57751 7--26. . . . . . . . . . . .57760 5--43. . . . . . . . . . . .57769 5--59. . . . . . . . . . . .57772 5--8. . . . . . . . . . . .57773 5--16, 5--18. . . . . . . . . . . .57776 5--72. . . . . . . . . . . .57778 5--59. . . . . . . . . . . .57781 5--48. . . . . . . . . . . .57782 5--48. . . . . . . . . . . .57791 5--50. . . . . . . . . . . .57803 5--58, 7--22, 7--26. . . . . . . . . . . .57804 5--60, 5--62, 7--22, 7--26. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-14


57807 5--58, 5--8, 7--4, 7--5, 7--6,. . . . . . . . . . . .7--7, 7--8, 7--9

57820 5--4, 5--6, 5--8. . . . . . . . . . . .57822 5--4, 5--6. . . . . . . . . . . .57825 5--34. . . . . . . . . . . .57828 5--34. . . . . . . . . . . .57835 5--44. . . . . . . . . . . .57849 5--46. . . . . . . . . . . .57852 5--44. . . . . . . . . . . .57856 5--48. . . . . . . . . . . .57858 5--4, 5--6. . . . . . . . . . . .57860 5--44. . . . . . . . . . . .57866 5--44. . . . . . . . . . . .57870 5--44. . . . . . . . . . . .57871 7--20. . . . . . . . . . . .57872 7--20, 7--24. . . . . . . . . . . .57873 5--64. . . . . . . . . . . .57874 5--64. . . . . . . . . . . .57875 5--64, 5--66. . . . . . . . . . . .57877 7--14. . . . . . . . . . . .57889 5--10. . . . . . . . . . . .57892 5--44. . . . . . . . . . . .57896 5--44. . . . . . . . . . . .57904 5--48. . . . . . . . . . . .57905 5--10. . . . . . . . . . . .57908 5--43. . . . . . . . . . . .57910 5--43. . . . . . . . . . . .57918 7--14. . . . . . . . . . . .57919 7--14. . . . . . . . . . . .57925 5--54. . . . . . . . . . . .57934 5--22, 5--24. . . . . . . . . . . .57936 5--44, 5--44. . . . . . . . . . . .57941 5--6. . . . . . . . . . . .57942 5--72. . . . . . . . . . . .57945 5--74, 5--76. . . . . . . . . . . .57946 5--74, 5--76. . . . . . . . . . . .57953 5--74, 5--76. . . . . . . . . . . .57955 5--74, 5--76. . . . . . . . . . . .57956 5--72. . . . . . . . . . . .57957 5--72. . . . . . . . . . . .57967 5--74, 5--76. . . . . . . . . . . .57968 5--74, 5--76. . . . . . . . . . . .57970 7--14. . . . . . . . . . . .57976 5--6. . . . . . . . . . . .57977 5--6. . . . . . . . . . . .57978 5--6. . . . . . . . . . . .57979 5--6, 5--68, 5--69. . . . . . . . . . . .57982 5--56, 8--15. . . . . . . . . . . .57984 5--44. . . . . . . . . . . .57992 5--68, 5--69. . . . . . . . . . . .57993 5--68. . . . . . . . . . . .57994 5--31, 5--68. . . . . . . . . . . .58035 5--44. . . . . . . . . . . .58038 7--7. . . . . . . . . . . .58041 7--4. . . . . . . . . . . .58044 5--13. . . . . . . . . . . .58045 5--13. . . . . . . . . . . .58049 9--4. . . . . . . . . . . .58065 7--4, 7--7. . . . . . . . . . . .58068 7--5, 7--8. . . . . . . . . . . .


58077 5--43. . . . . . . . . . . .58084 5--29. . . . . . . . . . . .58084 5--30. . . . . . . . . . . .58087 5--16. . . . . . . . . . . .58098 5--13. . . . . . . . . . . .58110 5--13. . . . . . . . . . . .58113 7--13. . . . . . . . . . . .58120 5--4, 5--29, 5--30. . . . . . . . . . . .58121 7--11. . . . . . . . . . . .58122 5--4, 9--10. . . . . . . . . . . .58130 7--8. . . . . . . . . . . .58133 7--5. . . . . . . . . . . .58136 7--9. . . . . . . . . . . .58139 7--6. . . . . . . . . . . .58194 6--4. . . . . . . . . . . .58206 5--10. . . . . . . . . . . .58207 5--10. . . . . . . . . . . .58209 7--14. . . . . . . . . . . .58210 7--14. . . . . . . . . . . .58218 5--10. . . . . . . . . . . .58219 5--10. . . . . . . . . . . .58220 5--10. . . . . . . . . . . .58222 5--10. . . . . . . . . . . .58228 5--43. . . . . . . . . . . .58236 5--43. . . . . . . . . . . .58237 5--43. . . . . . . . . . . .58238 5--43. . . . . . . . . . . .58244 5--43, 5--48. . . . . . . . . . . .58246 5--44. . . . . . . . . . . .58248 5--6. . . . . . . . . . . .58254 5--46. . . . . . . . . . . .58275 5--44. . . . . . . . . . . .58277 5--43. . . . . . . . . . . .58279 5--43, 5--50. . . . . . . . . . . .58281 5--44. . . . . . . . . . . .58287 5--43. . . . . . . . . . . .58290 5--44. . . . . . . . . . . .58293 5--44. . . . . . . . . . . .58296 7--13. . . . . . . . . . . .58298 5--43. . . . . . . . . . . .58300 5--26. . . . . . . . . . . .58311 5--50. . . . . . . . . . . .58319 5--50. . . . . . . . . . . .58320 5--50. . . . . . . . . . . .58321 5--50. . . . . . . . . . . .58328 5--52. . . . . . . . . . . .58329 5--48. . . . . . . . . . . .58329 5--48. . . . . . . . . . . .58330 5--48. . . . . . . . . . . .58331 5--52. . . . . . . . . . . .58337 5--48. . . . . . . . . . . .58338 5--10. . . . . . . . . . . .58345 5--10. . . . . . . . . . . .58346 5--29. . . . . . . . . . . .58347 5--10. . . . . . . . . . . .58349 5--10. . . . . . . . . . . .58359 5--44. . . . . . . . . . . .58361 5--43. . . . . . . . . . . .58366 5--6, 5--34. . . . . . . . . . . .58368 5--54. . . . . . . . . . . .

CROSS REFERENCE

11-15365 MM173 (6--90)


58376 5--16. . . . . . . . . . . .58377 5--16. . . . . . . . . . . .58381 5--16. . . . . . . . . . . .58395 5--68. . . . . . . . . . . .58395 5--69. . . . . . . . . . . .58399 5--48. . . . . . . . . . . .58424 5--38. . . . . . . . . . . .58460 5--38. . . . . . . . . . . .58465 5--38. . . . . . . . . . . .58476 5--38. . . . . . . . . . . .58476 5--4. . . . . . . . . . . .58477 5--38. . . . . . . . . . . .58481 5--38. . . . . . . . . . . .58482 5--38. . . . . . . . . . . .58483 5--38. . . . . . . . . . . .58484 5--38. . . . . . . . . . . .58485 5--38. . . . . . . . . . . .58485 5--4. . . . . . . . . . . .58488 5--40. . . . . . . . . . . .58489 5--6, 5--38, 7--16. . . . . . . . . . . .58490 5--10, 5--38. . . . . . . . . . . .58494 5--10, 5--38. . . . . . . . . . . .58496 5--38. . . . . . . . . . . .58497 5--40. . . . . . . . . . . .58498 5--40. . . . . . . . . . . .58506 5--4, 9--13. . . . . . . . . . . .58507 5--4, 9--13. . . . . . . . . . . .58509 5--4, 9--13. . . . . . . . . . . .58510 7--7, 7--8, 7--9. . . . . . . . . . . .58511 7--7, 7--8, 7--9. . . . . . . . . . . .58512 7--7, 7--8, 7--9. . . . . . . . . . . .58517 5--64, 5--66. . . . . . . . . . . .58518 7--7, 7--8, 7--9. . . . . . . . . . . .58519 7--7, 7--8, 7--9. . . . . . . . . . . .58520 7--7, 7--8, 7--9. . . . . . . . . . . .58524 5--38. . . . . . . . . . . .58529 5--48. . . . . . . . . . . .58534 5--26, 5--27, 5--28. . . . . . . . . . . .58535 5--50. . . . . . . . . . . .58538 5--29, 5--30. . . . . . . . . . . .58543 5--4, 5--6. . . . . . . . . . . .58563 5--6. . . . . . . . . . . .58572 5--10. . . . . . . . . . . .58574 5--10. . . . . . . . . . . .58581 6--4. . . . . . . . . . . .58582 6--4. . . . . . . . . . . .58588 6--4. . . . . . . . . . . .58589 6--4. . . . . . . . . . . .58590 6--4. . . . . . . . . . . .58591 5--58. . . . . . . . . . . .58592 5--16, 5--18. . . . . . . . . . . .58634 5--36. . . . . . . . . . . .58640 5--36. . . . . . . . . . . .58644 5--36. . . . . . . . . . . .58647 5--36. . . . . . . . . . . .58651 5--36. . . . . . . . . . . .58652 5--36. . . . . . . . . . . .58658 5--36. . . . . . . . . . . .58659 5--36. . . . . . . . . . . .58660 5--36. . . . . . . . . . . .


58661 5--36. . . . . . . . . . . .58669 5--36. . . . . . . . . . . .58676 5--36. . . . . . . . . . . .58677 5--36. . . . . . . . . . . .58678 5--48. . . . . . . . . . . .58679 5--36. . . . . . . . . . . .58680 5--36. . . . . . . . . . . .58681 5--36. . . . . . . . . . . .58682 5--36. . . . . . . . . . . .58694 5--36. . . . . . . . . . . .58695 5--36. . . . . . . . . . . .58696 5--36. . . . . . . . . . . .58704 5--31, 5--32. . . . . . . . . . . .58724 5--8. . . . . . . . . . . .58737 5--56. . . . . . . . . . . .58742 5--43. . . . . . . . . . . .58743 5--46. . . . . . . . . . . .58745 5--22. . . . . . . . . . . .58745 5--22. . . . . . . . . . . .58748 5--56. . . . . . . . . . . .58759 5--8. . . . . . . . . . . .58762 5--56. . . . . . . . . . . .58767 5--46. . . . . . . . . . . .58768 5--8. . . . . . . . . . . .58769 5--58. . . . . . . . . . . .58772 5--50. . . . . . . . . . . .58773 7--10. . . . . . . . . . . .58775 5--56. . . . . . . . . . . .58776 5--10. . . . . . . . . . . .58779 5--10. . . . . . . . . . . .58780 5--12. . . . . . . . . . . .58786 5--8. . . . . . . . . . . .58789 5--12. . . . . . . . . . . .58793 5--56. . . . . . . . . . . .58796 5--56. . . . . . . . . . . .58797 5--56. . . . . . . . . . . .58807 5--56. . . . . . . . . . . .58810 5--56. . . . . . . . . . . .58819 5--8, 5--64, 5--66. . . . . . . . . . . .58820 5--64, 5--66. . . . . . . . . . . .58824 5--64, 5--66. . . . . . . . . . . .58828 5--10. . . . . . . . . . . .58829 5--10. . . . . . . . . . . .58842 5--54. . . . . . . . . . . .58844 5--6. . . . . . . . . . . .58846 5--22, 5--24. . . . . . . . . . . .58848 5--48. . . . . . . . . . . .58850 5--16. . . . . . . . . . . .58858 5--72. . . . . . . . . . . .58864 5--6. . . . . . . . . . . .58898 5--6, 7--14. . . . . . . . . . . .58905 5--22. . . . . . . . . . . .58910 5--12. . . . . . . . . . . .58910 7--14. . . . . . . . . . . .58911 5--8. . . . . . . . . . . .58912 5--8. . . . . . . . . . . .58913 5--8. . . . . . . . . . . .58914 5--8. . . . . . . . . . . .58915 5--8. . . . . . . . . . . .58916 5--8. . . . . . . . . . . .

CROSS REFERENCE

365 MM173 (6--90)11-16


58924 5--56. . . . . . . . . . . .58925 8--4. . . . . . . . . . . .58929 5--74. . . . . . . . . . . .58932 5--41. . . . . . . . . . . .58933 5--72. . . . . . . . . . . .58934 5--72. . . . . . . . . . . .58941 5--72. . . . . . . . . . . .58948 7--20. . . . . . . . . . . .58950 7--18. . . . . . . . . . . .58951 7--14. . . . . . . . . . . .58955 7--19. . . . . . . . . . . .58956 7--19. . . . . . . . . . . .58957 7--16. . . . . . . . . . . .58958 7--14. . . . . . . . . . . .58962 7--16. . . . . . . . . . . .58963 7--16. . . . . . . . . . . .58964 7--14. . . . . . . . . . . .58966 7--16. . . . . . . . . . . .58967 7--14. . . . . . . . . . . .58968 7--14. . . . . . . . . . . .58973 7--16. . . . . . . . . . . .58974 7--14, 7--16. . . . . . . . . . . .58981 5--4, 5--38. . . . . . . . . . . .59054 5--66. . . . . . . . . . . .59632 5--64, 5--66. . . . . . . . . . . .61110 5--38. . . . . . . . . . . .62389 5--68. . . . . . . . . . . .62390 5--68. . . . . . . . . . . .62530--1 5--58. . . . . . . . .63266 7--22, 7--26. . . . . . . . . . . .63810 5--18, 6--6, 7--20, 7--24. . . . . . . . . . . .63814 7--18. . . . . . . . . . . .63837 7--18. . . . . . . . . . . .63852 5--56. . . . . . . . . . . .64141--1 5--8. . . . . . . . .64533 5--10. . . . . . . . . . . .64595 5--10, 5--38. . . . . . . . . . . .64991 5--66. . . . . . . . . . . .65129 5--50. . . . . . . . . . . .65145--1 5--68, 5--69. . . . . . . . .67004 7--28. . . . . . . . . . . .67290 5--46. . . . . . . . . . . .67811 5--68, 5--69. . . . . . . . . . . .68058 5--22. . . . . . . . . . . .68106 5--16, 5--18, 6--4, 7--14. . . . . . . . . . . .68198 5--4. . . . . . . . . . . .68275 5--12. . . . . . . . . . . .68297 5--52. . . . . . . . . . . .68616 5--22. . . . . . . . . . . .69234 5--8. . . . . . . . . . . .69266 5--24. . . . . . . . . . . .


69571 5--8. . . . . . . . . . . .69582 5--44, 5--50. . . . . . . . . . . .69743 5--44. . . . . . . . . . . .72025--S7 10--8. . . . . . . .72034--S 9--6. . . . . . . . .72432--S 9--10, 10--12. . . . . . . . .75365 5--52. . . . . . . . . . . .75939 5--34. . . . . . . . . . . .76058 5--48. . . . . . . . . . . .76589--2 5--18, 6--4. . . . . . . . .76721 5--6. . . . . . . . . . . .77097 5--34, 5--54, 5--70. . . . . . . . . . . .77101 5--34, 8--10. . . . . . . . . . . .78143 5--30. . . . . . . . . . . .82268 5--34. . . . . . . . . . . .82310 5--31, 5--32. . . . . . . . . . . .82315 5--31, 5--32. . . . . . . . . . . .82333 8--8. . . . . . . . . . . .82368 5--34. . . . . . . . . . . .82386 5--34. . . . . . . . . . . .82505 6--4. . . . . . . . . . . .82525 5--4, 5--28. . . . . . . . . . . .82526 5--28. . . . . . . . . . . .82533 5--29, 5--30. . . . . . . . . . . .82534 5--22. . . . . . . . . . . .82537 5--14. . . . . . . . . . . .82544 5--28. . . . . . . . . . . .82545 5--41. . . . . . . . . . . .82626 5--58. . . . . . . . . . . .82627 5--16. . . . . . . . . . . .82660 5--22. . . . . . . . . . . .82661 5--34, 5--41. . . . . . . . . . . .82674 5--22. . . . . . . . . . . .82684 6--4. . . . . . . . . . . .82685 5--30. . . . . . . . . . . .82688 5--32. . . . . . . . . . . .82691 6--4. . . . . . . . . . . .82697 5--4, 9--13. . . . . . . . . . . .82733 5--34. . . . . . . . . . . .82739 5--38. . . . . . . . . . . .82764 5--68, 5--69. . . . . . . . . . . .82767 5--68, 5--69. . . . . . . . . . . .82818 5--74, 5--76. . . . . . . . . . . .82822 5--76. . . . . . . . . . . .82830 5--46. . . . . . . . . . . .87515 5--6. . . . . . . . . . . .87536 5--58. . . . . . . . . . . .87631 5--46, 5--46. . . . . . . . . . . .87663 8--11. . . . . . . . . . . .87837--S 10--6. . . . . . . . .87866 5--58. . . . . . . . . . . .

CUSTOMER DOCUMENTS

12-1365 MM173 (3--90)

SECTION 12CONTENTS

PageTENNANT COMPANY LIMITED

WARRANTY 12-3. . . . . . . . . . . . . . . . . . . . . . . . . . .TENNANT COMPANY, TENNANT

COMPANY SUBSIDIARIES, ANDMAJOR PARTS AND SERVICELOCATIONS DIRECTORY 12-5. . . . . . . . . . . . . .

CUSTOMER DOCUMENTS

365 MM173 (3--90)12-2

CUSTOMER DOCUMENTS

12-3365 MM173 (3--90)

TENNANT COMPANY LIMITED WARRANTYNEW MACHINES

Tennant Company warrants to the original purchaser for the period stated below that goods manufactured by itwill be free from defects of workmanship and material, provided such goods are installed, operated, andmaintained in accordance with Tennant Company’s written manuals or other instructions. No warranty is madewith respect to items supplied by Tennant Company on special order of purchaser. Tennant Company’s soleobligation under this Warranty will be to repair and replace, at Tennant Company’s option, parts that do notconform to this Warranty.

SIX--MONTH LABOR COVERAGE (U.S.A. AND CANADA ONLY)For six (6) months in the U.S.A. or Canada, thirty (30) days elsewhere, from date of installation, TennantCompany will, at its option, provide labor for repair, pay for outside repair service, or pay the customer straighttime in accordance with Tennant Company’s flat rate schedule for particular warranty repairs. After six (6)months, Tennant Company’s sole obligation shall be limited to the repair or replacement, at Tennant Company’soption, of parts that do not conform to this Warranty according to the schedule below.

BATTERIES AND TIRESBatteries and tires will be replaced if failure occurs due to defective material or workmanship within ninety (90)days from date of purchase. Thereafter, a pro rata adjustment from date of purchase to twelve (12) months willbe made. The pro rata adjustment price of the replacement battery and/or tire will be the Tennant Companycurrent price as of the adjustment request less 1/12th of that price for each month remaining in the twelve (12)month period. This Warranty applies only to batteries and tires purchased from Tennant Company and installedin vehicles used in normal service.

BRUSHESBrushes that fail due to defective material or workmanship will be replaced on a pro rata basis within the firsttwelve (12) months of purchase. The replacement price will be calculated by multiplying the current TennantCompany price by the percentage of usable bristle remaining at the time of adjustment.

MACHINE WARRANTY PERIODTennant Company warrants its equipment for a set number of months or for a set number of hours of use,whichever comes first. The warranty periods and hours of use vary depending upon the machine model. Thewarranty periods for Tennant Company’s various machines are:

SCARIFIERSMachine Model Warranty Period Machine Model Warranty PeriodG 12 months/500 hours L2 12 months/500 hoursK4 12 months/500 hours RS/TLR 12 months/500 hoursKDC 12 months/500 hours

SCRUBBERSMachine Model Warranty Period Machine Model Warranty Period465/480 24 months/750 hours 528 24 months/2000 hours1465/1480 24 months/750 hours 530E 24 months/2000 hours510E 24 months/2000 hours (except Duramertsolution

(except Duramert solution and recovery tanksand recovery tanks, and 5 years/5000 hours)optional Pre-Sweept hopper 550 12 months/1500 hours5 years/5000 hours) 550E 12 months/1500 hours

SWEEPERSMachine Model Warranty Period Machine Model Warranty Period95 GR 24 months/2000 hours 235 24 months/1250 hours95 24 months/2000 hours (except Duramerthopper140/140E 12 months/500 hours 5 years/5000 hours)186 18 months/500 hours 255 Series II 18 months/1500 hours215 18 months/750 hours 275 Series II 24 months/2000 hours242E 24 months/1750 hours 285 24 months/2000 hours

365 24 months/2000 hours

CUSTOMER DOCUMENTS

365 MM173 (3--90)12-4

RECONDITIONED MACHINESTennant Company warrants to the purchaser of reconditioned equipment, purchased from Tennant Company, forthe period of ninety (90) days from the date of delivery that the purchased equipment will be free from defects ofworkmanship and material, provided such equipment is operated and maintained according to Tennant Companywritten manuals or instructions. Tennant Company’s sole obligation under this Warranty will be to repair andreplace, at Tennant Company’s option, parts that do not conform to this Warranty.No warranty of any kind is extended to equipment that is sold for salvage.

LABOR COVERAGEFor thirty (30) days from date of delivery Tennant Company will, at its option, provide labor for repair, pay outsiderepair service, or pay the customer straight time in accordance with Tennant Company flat rate schedule forparticular warranty repair. After thirty (30) days, Tennant Company’s sole obligation shall be limited to the repairor replacement, at Tennant Company’s option, of parts that do not conform to this Warranty.

DEMONSTRATOR MACHINESDemonstrator machines purchased from Tennant Company shall carry one of the following limited warranties:

1. Demonstrator machines purchased without a demonstrator discount carries the same warranty as newmachines;

2. Demonstrator machines purchased with a demonstrator discount carries the amount of warranty remainingon the unit from the original delivery date or the same warranty as a reconditioned machine, whichever isgreater.

NOTE: Demonstrator machines will always carry a minimum of 30 days labor.

REPAIR PARTSRepair parts supplied by Tennant Company are warranted against defects for the period stated below. TennantCompany’s obligation is limited to the replacement of the warranted part, and Tennant Company shall not beobligated to provide labor (except certain engines also stated below) in installing such part.

ENGINES, SHORT BLOCKS, AND LONG BLOCKSManufacturer Warranty Period Manufacturer Warranty PeriodContinental 1 year or 1500 hours parts & labor Perkins 1 year or 1500 hours parts & laborKohler 1 year or 1500 hours parts & labor Kubota 1 year or 1500 hours parts & labor

(except Kohler Model K181S --500 hours)Briggs & Stratton 90 days or 200 hours parts &labor Wisconsin 1 year or 500 hours parts & laborOnan 1 year or 1500 hours parts & labor Ford 1 year or 1500 hours parts only

D Engine part replacements such as water pumps, carburetors, and alternators are warranted for thirty (30)days parts only, no labor.D Labor is to include only the time it takes to repair an engine. It does not include removal and replacementnor does it include travel time.MAJOR HYDRAULIC COMPONENTS (PUMPS, MOTORS, CYLINDERS, AND CONTROL VALVES)

Manufacturer Warranty Period Manufacturer Warranty PeriodCessna 1 year parts only Oilgear 1 year parts onlyChar--Lynn 1 year parts only Gresen 90 days parts onlyVictor (Dukes) 1 year parts only MTE 90 days parts onlyRoss 1 year parts only Barnes 90 days parts onlyVickers 1 year parts onlyD All seal kits and replacement parts are warranted for thirty (30) days parts only.MAJOR ELECTRIC MOTORS

Manufacturer Warranty Period Manufacturer Warranty PeriodBaldor 1 year parts only Ohio Electric 1 year parts onlyGeneral Electric 1 year parts only HK Porter 1 year parts only

All other repair parts are warranted for thirty (30) days only.

SERVICE LABORLabor performed by a Tennant Company service representative shall be warranted for thirty (30) days from thedate the repairs are completed. This policy does not cover work performed by any service company, other thanTennant Company, and is restricted to the specific repair operation or component for which a claim is made.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESSED OR IMPLIED WARRANTIESINCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS AND OF ALL OTHER OBLIGATIONSAND LIABILITIES ON THE PART OF TENNANT COMPANY, INCLUDING LIABILITIES FOR DIRECT,IMMEDIATE, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE FAILURE OFANY MACHINE OR PART OF IT TO OPERATE PROPERLY, INCLUDING THE COST OR EXPENSE OFPROVIDING SUBSTITUTE EQUIPMENT OR SERVICE DURING PERIODS OF MALFUNCTION ORNON--USE.

This Warranty cannot be extended, changed, or modified by any representative of Tennant Company.

CUSTOMER DOCUMENTS

12-5365 MM173 (3--90)

TENNANT COMPANY, TENNANT COMPANY SUBSIDIARIES, ANDMAJOR PARTS AND SERVICE LOCATIONS DIRECTORY

LOCATION

NORTH AMERICA

U.S.A.

CALIFORNIALos Angeles Parts and Service Center2861 East La PalmaP. O. Box 66066Anaheim, CA 92806Phone: (714) 630--0800FAX: (714) 630--6934

GEORGIAAtlanta Parts and Service Center5805 Peachtree Corners E. Rd.Norcross, GA 30092Phone: (404) 447--1500FAX: (404) 449--0418

ILLINOISChicago Parts and Service Center630 Supreme DriveP. O. Box 590Bensenville, IL 60106Phone: (708) 595--1770FAX: (708) 595--5635

MICHIGANDetroit Parts and Service Center5601 Enterprise Dr.P. O. Box 927Warren, MI 48090Phone: (313) 573--6600FAX: (313) 573--2619

MINNESOTATennant Company, World HeadquartersMinneapolis Factory Customer Services701 N. Lilac Dr.Minneapolis, MN 55422Phone: (800) 553--8033 or (612) 593--8850FAX: (612) 540--1437

Mailing Address:P. O. Box 1452Minneapolis, MN 55440

PENNSYLVANIAPhiladelphia Parts and Service Center855 Bethel AvenueP. O. Box 220Pennsauken, NJ 08110Phone: (609) 665--2231FAX: (609) 665--4894

TEXASDallas/Ft. Worth Parts and Service Center1610 111th StreetGrand Prairie, TX 75050Phone: (214) 647--0801FAX: (214) 641--4011

CANADA

ONTARIOTennant1329 Cardiff BoulevardMississauga, OntarioCanada L5S 1R2Phone: (416) 670--8599FAX: (416) 670--8547

SOUTH AMERICA

BRAZILEquipamentos Tennant LimitadaRus Alvares Cabral Nr. 871Diadema -- SP -- Brazil CEP 09900Phone: (55) 11--456--2656FAX: (55) 11--465--4160

ASIA

JAPANTennant Japanc/o Nippon Yusoki Co., Ltd.1--1, 2--chome, HigashikotariNagaokakyo-shi, Kyoto, 617JAPANPhone: 075--956--8613Telex: 05429926 NYK HJFAX: 075--955--8993

AUSTRALIA

AUSTRALIATennant Australia10 Hope StreetErmington, N.S.W. 2115AustraliaPhone: (61) 2--858--5811Telex: AA27393FAX: (61) 2--858--1995

EUROPE

NETHERLANDSTennant N.V.Industrielaan 65400 AAUden, N.B., NetherlandsPhone: (31) 4132 63955Telex: 844 74768FAX: (31) 4132 50008

(continued on following page)

CUSTOMER DOCUMENTS

365 MM173 (3--90)12-6

EUROPE CONTINUED

UNITED KINGDOMTennant Maintenance Systems, Ltd.Central AvenueEast MoleseySurrey KT8 OQZUnited KingdomPhone: (44) 1--941--5585FAX: (44) 1--941--4678

WEST GERMANYTennant N.V.Walter--Freitag--Straβe 395630 Remscheid 11 (Lüttringhausen)B.R.D.Phone: (49) 2191--59140Telex: (841) 08 513 478 TENV D.FAX: (49) 2191--561436

This is a listing ofmajor Tennant Company parts and service centers. Parts and service are also available at many other Tennant Companycenters or distributors located around the world. To determine your nearest Tennant Company representative, phone or write the TennantCompany World Headquarters.

TENNANT SERVICE LITERATURE AVAILABLE...

A variety of information is available to you in forms to suit your needs. Thefollowing is a list of those publications that relate to the Model 365 family ofmachines:

Machine TENNANTModel Publication Form Part No.

365 Operation, Maintenance,and Parts Manual Printed MM173

365 Operation, Maintenance,and Parts Manual Microfiche 85173

365 Operator Handbook Printed MM174

365 Ford KSG-411, KSG-416Engine Service Manual Printed 38961

Keep your manuals in a safe, convenient location for your future reference inorder to operate, maintain, and order repair parts for your machine. Everyonewho operates, maintains, or purchases parts for the machine should have easyaccess to a copy of the manual.

To get pricing information or to order copies of these publications, contact yournearest Tennant Company parts warehouse, distributor, or sales representative.

Date post:	28-Feb-2022
Category:	Documents
Upload:	others
View:	6 times
Download:	0 times