3D Touch Portable Interactive Whiteboard Manual 3.3.0.0

7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0

1/21

3D TOUCH INTERACTIVE WHITEBOARD MANUAL

1

USER MANUALFor 3D Touch Interactive Whiteboard

(Version 3.3 N))


2/21


3/21


3

Introduction

3D Touch Interactive Whiteboard is attached with Projector/LCD and turns any flat surfaces into interactive and

collaborative workspace. It is an inexpensive Interactive Solution.

Key Features

1, Portable, Reliable, Simple installation;

2, Automatic Calibration within 4 seconds;

3, Screen Size is not limited, Support up to 150;

4, Turns LCD Screen into Interactive Whiteboard;

5, Multi Touch. Two or more users can write on it at the same time

Specifications

Active screen area 40- 150''diagonal

Shipping size 25 cm 26 cm 7 cm

Shipping weight 0.5 kg

Technology Optical + Laser technology

Mouse Function Double click function. Right-click function can be

achieved by maintaining the pressure on the board for

2 seconds.

Power Energy is taken from a computer via a USB cable.

Power Consumption 1w.

Delay Time


4/21


4

Package Includes

Calibration Device 12m USB Cable CDs

Infrared Pen Ceiling Mount Pointer (Optional)

Battery size for infrared pen/ Pointer: 2 pieces, AAA (non included)


5/21


5

Hardware Installation

Install Calibration Device

Install the Calibration Device to the ceiling with the mount and the distance to the front of the projection screen /

surface (based on 80 Projection Screen) should be approximately 1m for Short Throw Model.

Note:For 80 active size (Projection screen), the installation distance is about0.45 m-0.8m for ultra short throw

Sensor part, and about 2.2m-3.2m for long throw Sensor part.

Pic 1

Turn LCD TV screen into interactive: Connect the computer with the LCD TV through VGA cable and then

follow the following steps.

Connect Calibration Device

Connect the Calibration Device to the Computer (Laptop) with USB Cable. (Plug USB Cable into one of back

ports of computer. For Laptop, extra power may beneeded

Please note: If there is already a Video Camera/Webcam in the computer/Laptop, please disable it


6/21


6

Calibration Software

Introduction

1. Operate menu list

Pic1

Operate Menu list including run, stop, parameter settings, Auto Mask Clutter, Manual Mask Area, Manual

Calibration, Automatic Calibration, Disable the optical pen control and Exit.

(1) Parameter setting: almost parameter of the calibration software here, such as Proportion of the

spot, Eraser in multiples of spot, Brightness coefficient, Auto calibrate average brightness.

(2) Auto mask clutter: chose it, then software will mask the bright spot automatic.

(3) Manual mask area: manually mask the bright spot.

(4) Manual calibration: there are two kind of manual calibration, 25point and 36point.

(5) Automatic calibration: automatically make the calibration.

(6) Disable the optical pen: chose it, then you disable of function of the pen or finger, so you cannot

use the pen or the finger any more. Usually when the mouse out of control before the calibration, then

you can chose it.

(7) Exit: mean you wan not use the software and exit it.

Note: in the top right corner, which is not mean exit the software, it is mean you close display on

window, but the software will be there (bottom right corner)


7/21


7

2. Parameter Setting(As Pic6)

Pic 2

(1), Set the proportion of the spot (20%~80%): to set how large the spot will cause the sensor to detect. ( No

mean for pen touch model)

(2), Eraser in multiples of spot (3~7): set how large the spot will appear eraser. (No mean for pen touch model)

(3), Normal use of the brightness coefficient (0~250): adjust the average brightness of the software interface

when the device works normally.

Note: when you adjust this data, you should restart the software.

(4), Auto calibrates average brightness (0~255): adjust the average brightness of the software interface when

does calibration

(5), Auto calibrate light gray (0~255): when calibration failed, and the projection screen is very gray, then you

can adjust this data (increase) , when the projection is very brighten, then decrease.

(6), whether to record video: to record the auto calibration video.

(7), There are three model for usage, the pen touch, the finger touch and the rear projector.

(8), Manual Collection spot: when you writing, it interrupts, then do it (As Pic3)

(9), Default settings, click it; all parameter will be recommended value.

Pic 3


8/21


8

Pic7

3. Installation and debugging

(1). Show Status: check frame rate and real-time frame rate of the camera. If the frame rate lower than 110fps,

then you should check if there any problem.

(2). Tuning webcam image mode: chose this mode before calibration, then you can see the screen more clearly

and then adjust the position of camera.

(3). Tuning laser transmitter image mode:( No mean for pen touch model)

(4).Normal Usage image mode: after calibration, then use this mode to check the image. (After you calibration,

then you can see the image in normal mode).

4. Help

(1) Language option: chose the language as you like.

(2) About: company and software information

5. Right click the minimized software menu

Pic 4

(1) Display the main windows: display the interface of the calibration software

(2) Coordinate calibration: not use this option for now.

(3)Auto run at system startup: chose it, the software will be start when the computer starts.

(4) Exit: Exit the software.


9/21


9

Calibration

Step 1: Place the small software CD-ROM into the CD drive and copy the Calibration Software and IWB

Application Softwarefolder in the CD-ROM onto your PCs hard disk drive.

Please Note: do not RUN the software from the CD.

Step 2: Open the file of Calibration Software, run IWB_Setup.exe; , Then there will be icon

on desk :

Step3: Please click Installation and debugging-Mode 1. Then you will see the screen as below. You can see

the projection screen clear from calibration software window.

Projection screen image

Pic5

Note: make sure all projection screens image are included in the calibration software intersurface. The

image should take over 50% to 80% of the software screen.

Software interface


10/21


10

Pic 6

Next, keep adjusting the location or angel of calibration device or move any strong light until there is no

green dot or area in the viewing window. Please note: If there is any green area in this calibration

software screen or calibration will not success.

Step 4:

Option 1: Automatic calibration:

Just click Operation, chose Automatic Calibration, then you will see as below:


11/21


11

Pic7

About 4 seconds, its finished.

Option 2:Manual Calibration

1, Please choose Auto Mask Clutterfrom Operationor you can pressCtrl+Shift+A. The software will

specify the active area automatically. The other area will be shielded by green mask.

Pic 8

2, Touch each corner and check if it can be seen from the calibration screen like below. If some corner is notincluded, please eraser the green mask (Mask Bitmap Edit-Erase Mask Area).until you can see the spot as

below


12/21


12

Pic 9

Pic 10

3, Click Manual Calibrationin the Operation.


13/21


13

Pic11

You enter the calibration process now. Please use Pen to click the center of the cross on the screen, finished one,

then another cross appear, repeat this until the 36th dot or 25thdot is finished.

Pic 12


14/21


14

After Calibration finished, Viewing Window will be minimized in the right corner of the computer.

To make the device run with system start. Please right click the Icon . And select Auto Run At System

Startup

l

Tip: No need to calibration again when the projector and signal device are not moved.

Now you could control the computer from the projection screen with the infrared pen.

Pic 13


15/21


15

Application Software Installation

Step 1: When system is Windows Vista or XP, please place the big software CD-ROM into the CD drive and copy

the DotNetFX35 folder in the CD-ROM onto your PC s hard disk drive. (Please skip this step with

Windows 7)

Please Note: do not RUN the software from the CD.

Step 2: Open the DotNetFX35and then run .

Step 3: Open the folder IWB Application Softwareand run , Chose the install path and

language, then click next stop to install GLboard, then you will see :There will be a icon of GLboard

on the desktop.

Now the Application software of GLboardis installed.

GLBoard Software Manual

Introduction of the main toolbar

When you use the GL Board at first time, double click

To pen the software, interface includes three areas as following:


16/21


16

Function of Each button in the tool bar

iron Name function

Start menu Open the menu list

Resource Local recourse: You can click it to find many pictures.

Network resource: you click it and then you can search

any picture as you like.

New page There are four options:

back Go back to the previous page

forward Forward to next page

Pen Write like a ball pen

brush Write like Chinese brush pen

Smart pen Convert the drawing to typewriting geometric shapes.

Operate area: picture or text edit

Toolbar


17/21


17

Multi-writing

mode

Support ten persons writing simultaneously. Attention,

when you use this mode which is new function, you

just can write.

Insert shape Several shapes can be chose, such as triangle,

square ,circle and so on

Import picture Insert picture from your computer

Import text Insert text frame, then edit the words

Fill Fill the geometric shapes with different color

Select stroke Select the handwriting on the page, and do drag and

zoom operation

Select picture Move geometric shapes, text and pictures

zoom in and

out

Zoom in or zoom out the picture

Pen color Adjust the any pens color

Fill color Chose the color to fill

Pen width Set stroke width and line type.

Erase Three options:

undo Cancel the last operation

redo Redo the operation just canceled by undo

Move Move the edit screen

windows Back to the desktop


18/21


18

Start Menu Introduction

Click the menu , then the tool list will pop up, click the option according to the different needs.

The File menu: including theNew, Open, Save, Save As Support

open PTS, PDF, Word, Excel,

PowerPoint and other file formats.

Insert Hyperlink: including the

Web Page, Disk File and

Documentation Page

Export: the current page could be

exported as the format of PNG, JPG,

BMP, ISF and XPS.

Change Background: used to

change the background of current page.

Tool Group Includes: Protractor,

Triangle, Ruler, Timer, Media Player,

Vide Capture, Mask, Magnifying glass,

Spotlight, Keyboard, Calculator,

Handwriting Recognition, Screen

Recording, External tool Management.Slide page navigation: users will

be required to open the slide and enter

the View Show status under the

desktop status, click on the function keys

then the Annotation, page up and down

could be achieved.


19/21


19

Minimize the Toolbar Introduction

Click to switch to the desktop Mode, then the right side of the desktop will appear Minimize toolbar, the

following is a description of each button:

Back to Desktop

Pen

White Page

Previous Page

Erase

Undo

Note Page

Previous Note Page

Black Page

Next Page

Insert Picture

Exit

Pen Size

MaskMagnifying glassSpotlight

Screenshot


20/21


20

Tips1. The most proper distance from calibration device to the screen is 55cm - 100cm if the projection screen is

70-80inch. Computer image taken by the device must include whole projection screen. you can open the

menu of Installationand chose tuning image mode 1, then you can see following:

2. When use the infrared pen do manual calibration. Place the pen tip at the center of the cross; hold the infrared

pen at an angle of3045 to the projection surface and then press. Please hold on until color of cross turns

blue from red. Then click next cross.

3, Best Installation way: Install the Calibration Device on the ceiling and there is no block between the tip of pen

The white place is projection

screen shoot by our camera.The white image must take

up 60-80% of total screen.


21/21


21

and device. If the Calibration Device cannot be installed on the ceiling, please make sure there is no block

between the tip of pen and the Calibration Device when operation, like users body or hand. If there is block,

interrupted lines would happen during writing.

(Remark: if battery is not available, interrupted lines would happen during writing too.)

4, Operate right click function: pressure the infrared pen for 2 seconds.

5, USB cable has to be plugged into the port in the back of Computer Box.

6, If the software screen is not red, click stop and set another camera in the list of device, then choose start

again.

7. If after calibration, window of software is minimized and the mouse can move, but operations of double-click

and right-click does not work, please check if you have installed any anti-virus software, which prohibits additional

mouse functions, so that you cannot use all the functions of mouse. Please turn off anti-virus software, and then

our software can be used normally.

8, If there is time delay of green light moving in the red screen of the calibration software, please open menu of

status and check actual frame rate. If it is less than 110, please change a computer or contact your seller.

9. If the calibration failed, then you can find the folder named Intermdiate, open it, then you will find folder

namedautocalibrate. This folder record what is happen to the calibration, and then analysis the picture in it, then

you can know why calibration failed. If you dontknow how to analysis, then send such folder to manufacturer or

your dealer.

End

Date post:	02-Mar-2018
Category:	Documents
Upload:	joshi-thomas
View:	261 times
Download:	1 times

3D Touch Portable Interactive Whiteboard Manual 3.3.0.0

Documents