Date post: | 22-Jul-2016 |
Category: |
Documents |
Upload: | advantage-feeders |
View: | 214 times |
Download: | 0 times |
3IN1FEEDERS 2015 Catalog 1
The answer you’re looking forSome of our more frequently asked questions 6
Grow profitsMinimal outlay – maximum returns 8-9
2015 Catalog
3IN1FEEDERS 2015 Catalog 2
Grain and Pellet Feeders
Weight: 700lbs
Assembled Dimensions: 8’0” x 5’5” x 4’9” (LxWxH)
Flat-packed Dimensions: 8’0” x 3’10” x 0’11” (LxWxH)
Volume: 51 bushels
Weight of feed: 1.5 tons of wheat
1.3 tons of barley/pellets
1.0 tons of oats
1800
Weight: 350lbs
Assembled Dimensions: 4’0” x 5’5” x 4’6” (LxWxH)
Flat-packed Dimensions: 4’0” x 3’10” x 0’9” (LxWxH)
Volume: 23 bushels
Weight of feed: 0.6 tons of wheat
0.5 tons of barley/pellets
0.4 tons of oats
800
Weight: 850lbs
Assembled Dimensions: 8’0” x 5’5” x 7’1” (LxWxH)
Flat-packed Dimensions: 8’0” x 3’10” x 1’1” (LxWxH)
Volume: 108 bushels
Weight of feed: 3.3 tons of wheat
2.8 tons of barley/pellets
2.1 tons of oats
3800
StrengthAll outer extremities are reinforced
to withstand the roughest treatment
from cattle.
3IN1FEEDERS are stronger because
they are formed from connected
sheetmetal, with flanged joints
instead of parts that are simply
butted up and welded.
Two year warranty 3IN1FEEDERS provides a standard two
year warranty on all purchases.
Fully galvanizedAll parts are galvanized, not painted,
ensuring the product lasts longer.
Tube components can often sit in the
mud and muck and rust quickly – all
tube on our feeders is hot gal dipped
to ensure that’s not the case.
Lifting frameAll feeders can be moved fully loaded.
The 1800 and 3800 are designed with
‘Z’ shaped rails under the trough to
spread the load.
Accurate feeding and consumption stickerThe Upper and Lower Adjusters have
a series of painted dimples on them –
allowing them to be set accurately.
The Lower Side Panels have a table
to show the intake at each adjuster
setting.
The table should be considered a
guide only but is a good starting point
for setting the feeder.
Adjuster Guard The Adjuster Guard is a part that
sits above the feed access area to
partition it into 4” gaps. This ensures
that animals stand in the same location
while feeding.
Volume stickersThe volume stickers allow you to quickly
determine the amount being consumed
and make adjustments if required
Quality componentsAll fasteners on our adjusters are
stainless steel – ensuring a long,
functional life. All rivets and Tek screws
have high quality coatings.
Sight glassesSight glasses are a simple and effective feature that can save you getting out of your vehicle to check the volume in the feeder.
Retractable roofOur roofs can be easily opened and handily fastened on the same side.
Number of stock per feederThere are many variables to the number of stock that can put on a feeder. The main consideration is what other sources of feed they have in their field. If stock are totally reliant on the feeders, they will visit the feeder more often. As a general rule the feeders are suitable for the following quantities of stock:
1800/3800
• 50 cattle
• 25 cows with 25 calves
• 50 calves
800
• 25 cattle
• 12 cows with 12 calves
• 25 calves
Stock per feeder
3IN1FEEDERS 2015 Catalog 3
Mobile Feeders
Weight: 1300lbs
Assembled Dimensions: 12’0” x 5’5” x 7’1” (LxWxH)
Flat-packed Dimensions: 8’0” x 3’10” x 2’5” (LxWxH)
Volume: 108 bushels
Weight of feed: 3.3 tons of wheat
2.8 tons of barley/pellets
2.1 tons of oats
MGF3800
Mobile Grain Feeders give farmers the convenience of filling the feeders up at a bin and taking them out to the field. They are ideal for rotational grazing systems.
The MGF3800 is constructed by adding
the tandem axle chassis system to the
3800 stationary feeder. The MGF1800
is constructed by adding the single axle
chassis system to the 1800 stationary
feeder.
Central wheel positionThe centralised axle reduces the load
on the tow ball of the towing vehicle.
Other mobile feeders on the market
have the axle at the rear which can
place over 2000lbs of load on your
tow ball, when most vehicles have
a maximum tow ball loading of just
660lbs. This can cause the kind of
catastrophic failure which can lead to
accidents.
Our tires are only 19” high (195/55/
R13C) and have a load rating of
2000lbs each.
Weight: 1050lbs
Assembled Dimensions: 12’0” x 5’5” x 4’9” (LxWxH)
Flat-packed Dimensions: 8’0” x 3’10” x 2’3” (LxWxH)
Volume: 51 bushels
Weight of feed: 1.5 tons of wheat
1.3 tons of barley/pellets
1.0 tons of oats
MGF1800 3IN1FEEDERS give farmers the control to limit the amount of supplement that stock consume.
We do this through our revolutionary saliva-restriction, Advanced Adjustment System.
While the 3IN1FEEDERS’ Advanced Adjustment System can be set to feed unrestricted amounts to stock, it can also limit the intake of cattle to 3lb / day.
3IN1FEEDERS can be used successfully to do the following:
1) Controlled feeding 2) Creep feeding; and 3) Free choice feeding
How do 3IN1FEEDERS work?Our Advanced Adjustment System requires stock to lick feed out of a groove between two adjusters.
Changing the position of these adjusters changes the amount that stock can consume.
Research has shown that when the lick system is in its most restricted setting, stock lick for approximately five minutes between periods of grazing.
The licking period is limited because livestock use the saliva on their tongue to get the feed out of the groove. The saliva decreases with each lick until the animal can no longer access the feed.
SuspensionMobile Feeders have suspension to
ensure the longevity of the products
by providing smooth transportation
at higher speeds.
The MGF3800 features load-sharing
springs to spread a full load evenly
over all four wheels.
3IN1FEEDERS have no maximum speed
limit. Many others have a maximum of
15mph.
Telescopic standsThe Mobile Feeders feature a
telescopic stand at each corner to
prohibit movement when uncoupled.
Adjustable axle heightOur Mobile Feeders are manufactured
to allow the axle(s) to be set at one of
three different heights (approx. 12”, 16”
and 20”) to suit different sized stock.
3IN1FEEDERS 2015 Catalog 4
Calf Creep Feeding
Cows / herd run before creep feeding
50
Increased cow stocking
rate due to creep feeding 6%
Extra cows run due to creep feeding
3
Gross profit of extra cows / head
$ 750
Increased gross profit / herd / year $2,250
table 1.1 Run more cows
Increase stocking rates – run more cows
Creep feeding produces animals at a marketable weight faster. This allows these cattle to be taken off the farm earlier and makes more pasture available to run reproductive stock.
Creep feeding develops calves faster so they can be weaned at a younger age (often 2-3 month earlier). Due to early weaning, cows that would otherwise have a calf at foot can be run harder, requiring less pasture and supplement to maintain condition. (table 1.1)
Creep feeding has a high feed conversionCreep feeding is one of the most efficient
forms of supplement feeding. Creep
feeding trials with calves using whole
oats have shown that 77-88lbs additional
live weight gain can be achieved over
unsupplemented calves during a 100-
day feeding period (NSW Department
of Primary Industry, Agfact A2.5.4).
Approximately 440lbs of oats was fed
Additional weight gain from creep feeding (lb)
80
Value of live weight / lb $ 1.60
Increased income from creep feeding / calf
$ 128.00
Cost of 440lb of oats ($180/ton)
$ 39.60
Gross profit / calf / annum $88.40
Calves / herd 50
Increased gross profit / herd / year
$4,420.00
table 1.2 High feed conversion
to achieve this weight gain offering a conversion of 5-5.7 : 1. (table 1.2)
3IN1FEEDERS 2015 Catalog 5
CG2
What is creep feeding?
Creep feeding is the process of
exclusively feeding unweaned
young stock.
How do the creep gates work?3IN1FEEDERS Creep Gates
deny cows access to the
feeding area because their
body size is too large to fit
through the gaps in the gates.
Depending on the breed, the
gaps will allow calves to enter
until they are 12 months of age.
The Creep Gate simplifies creep
feeding because the pivoting
gates enable farmers to quickly
and easily pivot them from the
transport/inactive position to
the engaged, creep feeding
position.
They are permanently attached
to the feeder making the feeder
simple to relocate. It is common
to attach only one Creep Gate
to a feeder to ad-lib feed calves
on one side and use the other
side to feed cows a restricted
ration, particularly heifers.
The gates have a horizontal bar
that can be positioned at nine
different heights to best suit
the size of the calf and prevent
young and small-framed cows
from entering.
They have a strong triangular
brace to prevent cows from
changing the shape of the area
the gate creates.
Gates have pins to prevent
cows from lifting them up.
Weight: 110lb
Assembled Dimensions: 8’2” x 4’7” x 3’10” (LxWxH)
Flat-packed Dimensions: 8’2” x 3’10” x 0’6” (LxWxH)
Weight: 90lb each
Assembled Dimensions: 4’1” x 4’7” x 3’10” (LxWxH)
Flat-packed Dimensions: 5’0” x 3’10” x 0’6” (LxWxH)
CG1
Early rumen development
Feeding high starch-based diets to calves
drastically reduces the time for the rumen
to develop.
Starch helps the conversion of the rumen
for processing milk at infancy to support a
large microbial population – essential for
processing fodder and grain/pellets.
While the additional feed will have a high
feed conversion, the primary benefit of a
developed rumen is that it allows young
stock to consume and process more pasture
– the most cost effective feed for growing
stock in peak pasture growth periods.
Benefits of creep feeding include:• Increase the weight gain of calves.
• Increase the number of calves that reach target weight by weaning.
• Allow calves to be weaned earlier.
• Increase the number of cows run by carrying fewer calves.
• Reduce the supplement cows require for the desired condition score prior to breeding, as weaning is earlier.
• Increase the number of heifers reaching the desired minimum breeding weight and improve conception rates.
• Increase the number of cows that conceive early in the breeding period.
Fig. 1 The rumen of a calf fed milk only shows little papillae development.
Fig. 2 The rumen of a calf fed milk and hay shows little papillae development.
Fig. 3 The rumen of a calf fed milk and grain shows significant papillae.
3IN1FEEDERS 2015 Catalog 6
Frequently Asked Questions
How does the 3IN1FEEDERS system control feed consumption better than other feeders?Critical to the success of controlling the
feed amount is to limit what an animal’s
tongue can touch with any one lick.
In the restricted setting, 3IN1FEEDERS
Advanced Adjustment System can position
feed 2” down between two plates.
The feed in the bottom of the groove can
sit so the depth of grains/pellets is only one
pellet deep, only allowing stock to lick
a few grains/pellets with each lick.
When the animal’s saliva depletes, they
cannot access feed.
While other feeders can also make stock
lick through a narrow gap, they allow stock
to put their tongues into the feed as deep
as the tongue will reach.
They access a lot more feed with each lick
so instead of stopping when they run out of
saliva, they stop when they grow tired
of licking.
3IN1FEEDERS’ control over the feed
amount is further enhanced by the use of
the Adjuster Guard – a set of holes dividing
the feed access area.
This part encourages stock not to move
along the trough, allowing more animals to
feed uninterrupted.
3IN1FEEDERS can also be adjusted to
free choice feed.
Why is the 3IN1FEEDERS system more efficient than periodic feeding?
Rumens contain different types of microbes
– some digest starch and sugars and
others digest cellulose.
Dietary upsets, such as feeding too much
concentrate only once per day, can cause
rapid change in the microbial population.
This changes fermentation patterns,
the rumen PH and interferes with fibre
digestion.
Animals that feed from 3IN1FEEDERS
receive numerous, small amounts of
supplement ensuring the rumen always
has the same feed content – maximizing
efficiency.
What stops them eating all day? Although the feed in 3IN1FEEDERS is
always accessible when the feeders are
set to restrict intake, stock can only access
it while they have sufficient saliva on their
tongue.
They require saliva to stick feed to their
tongue – without it, they can’t get the feed
out and into their mouth.
When their tongue dries, why won’t they just go between the water trough and feeder all day? Although proximity to the water supply will
increase the minimum amount received
from 3IN1FEEDERS, saliva is much stickier
than water. The supply of saliva is limited
because it comes through the glands in
the mouth from the fluid in the rumen.
How do you know they’re all getting a supplement? Bossy animals also run out of saliva –
leaving the feeder to other animals in the
flock to receive a supplement.
Many farmers observe that the trough
space is rarely full, feeding is less frantic
and stock are frequently coming and going
between the feeder and the rest of the
flock grazing in the field.
How are bullying stock discouraged from pushing others out of the way?
The Adjuster Guard features a series of
holes that animals eat through. Any feed
spilled from the feed access area and
through the Adjuster Guard falls in the
trough in front of them.
This means it is disadvantageous to move
along the trough, pushing other stock away
from the feeder.
How do you train stock to lick from the groove? Stock learn fastest if they have a reward
(a generous amount of feed) the first time
they come to the feeder.
This is done by using a safe feed and
opening the adjustment system to an
ad-lib position.
Other ways to help train stock are to put
some feed in the troughs and on the
ground around the feeder.
Each feeder has instruction stickers above
the troughs for more information.
Will rough cattle wreck my feeders? All feeders have reinforcing in the edges of
the troughs and weather protecting shields.
For added peace of mind, 3IN1FEEDERS
provide a full two year warranty on all
products after filling in a simple form.
3IN1FEEDERS began eight years ago.
We are yet to replace any part damaged
by cattle in any of our Next Generation
Feeders.
Is there enough rain protection to prevent feed getting wet?The 3IN1FEEDERS system holds the feed
in the licking area, up and out of the trough.
The side panels on the feeder are
designed with a gutter at the bottom of
them, draining any rain that hits them to
either end of the feeder, not into the feed.
The only feed that can get wet is the small
amount of feed sitting in the licking area.
Stock usually lick this out before it clogs.
If you have any further questions regarding 3IN1FEEDERS and their use, please feel free to contact us.
3IN1FEEDERS 2015 Catalog 7
Mineral Attachment
Loose Minerals are the most cost
effective form in which to supply the
mineral and vitamin requirements
of stock.
If Loose Minerals are substituted for
Lick Blocks, the savings can pay for the
investment in a matter of months.
Capacity: 250lbs
Weight: 22lbs
Dimensions: 30”x16”x22” (LxWxH)
Material: UV stable polyethylene
The Mineral Attachment ensures that
your stock receive their nutritional
requirements while reducing waste
and labour.
It has a cover over the access area to
protect the mineral feed from rain.
It can fasten to the end of Next
Generation Feeders making it easy
to move the mineral component of
the stock’s ration when they are
moved field.
Farmers can also hang them on iron
posts, gates or yard panels.
3IN1FEEDERS 2015 Catalog 8
Trial outline:
Duration: 60 days (from 120 to
180 days old)
Quantity: 20 in each supplement group, 10 in the control
group
Sex: Half steers and half
heifers in each group
Feed: No supplement group:
Pasture
Restricted barley group:
Pasture + 3.1lbs/day of
barley
Unrestricted oats group:
Pasture and 4.5lbs/day of oats
Results: The free choice oats group had the highest growth rates. However, this group sold for a discounted price due to them being considered “pot-bellied” with excessive amounts of flesh.
The restricted barley group sold at the highest price due to being in forward condition.
The growth rate of the group
was 0.42lb/day less than the free
choice oats group but sold for
$68.02 more than the oats group
and $106.56 more than the group
that wasn’t supplemented.
A recently concluded trial shows that while creep feeding is quite profitable, feeding a restricted ration is considerably more profitable than feeding free-choice oats.
Creep Feeding Trial
SALE PRICENo
SupplementBarley -
restrictedOats -
free choice
Avg. daily weight gain (lbs / head) 2.11 2.53 2.95
Total weight gain (lbs / head) 126.6 151.9 177
Sale weight (lbs / head) 450.4 486.1 517.5
Sale price / lbs $2.85 $2.95 $2.65
Sale price / head $1,283.64 $1,434.00 $1,371.38
Feeding expense / head* $0.00 $43.80 $49.20
Net Income/head $1,283.64 $1,390.20 $1,322.18
*Refer Feeding Expense table
3IN1FEEDERS 2015 Catalog 9
Profitable with lower prices 2014 prices have been higher than the historical average.
They are forecast to remain high for a number of years yet.
Even so, if we were to imagine creep feeding a restricted barley ration with beef at only 60% of current prices and the same input costs as experienced in this trial, it would be $46.41/head more profitable than not creep feeding.
Perhaps more remarkably, it would be $42.97/head more profitable than creep feeding a free-choice oats ration.
FEEDING EXPENSE No Supp.Barley - restricted
Oats - free choice
Feed price (ton) 0 $200.00 $180.00
Daily consumption (lbs / head)
0 3.1 4.5
Daily feed cost / head $0.00 $0.37 $0.28
Total feed cost / head (60 days)
$0.00 $16.80 $22.20
Labour / head - filling feeder
$0.00 $3.00 $3.00
Depreciation / head (15% on a $3200 investment)
$0.00 $24.00 $24.00
Total feeding expense / head
$0.00 $43.80 $49.20
$1,300.00
$1,200.00
$1,100.00
$1,000.00
$900.00
$800.00
$700.0060% 70% 80% 90%
Percentage of 01/11/14 prices
Net income with lower weaner prices
No supplement
Barley supplement
Oats – free choice
$1,500.00
$1,450.00
$1,400.00
$1,350.00
$1,300.00
$1,250.00
$1,200.00
No supplement
Barley supplement
Oats – free choice
Average weaner sale price
Sale
price
Sale
price
Sale
price
Net in
com
e
Net in
com
e
Net in
com
e
Opportunity for higher profitsThe feeders in the trial only had 20 calves feeding from each. Many farmers feed 50 calves with one feeder.
Feeding 50 calves with a feeder would spread the depreciation cost over more calves to reduce it from $24/head to less than $10/head.
The trial operated for 60 days. In many operations, creep feeding can operate for over 120 days.
A longer creep feeding period would increase growth rates over the cycle, increasing profits more than experienced in this trial.
3IN1FEEDERS 2015 Catalog 10
On-Farm Trials
3IN1FEEDERS regularly conduct on-farm trials to provide our customers with the necessary facts to make informed decisions. Please visit our website for full trial report.
Increasing 2nd year heifers’ pregnancy rates
Objective:
Heifers that have calved suffer significant strains on their condition after pregnancy and while producing milk.
They often struggle to be in adequate condition to become pregnant again three months after calving.
The trial will compare the profitability, weight and pregnancy rates of a group of heifers that are given 4.4lbs/day of cereal after giving birth, until 30 days after mating, compared to a group without supplement.
UPCOMING ON-FARM TRIAL
3IN1FEEDERS 2015 Catalog 11
Yearling Trial – Forage crop grazing
Objective:
Compare the profitability of a group of
yearlings grazing a forage crop with hay
against another group on the same feed
but with a supplement of 2lb/day of wheat.
Result summary:
The supplement mob grew an average of
3.3lb/day, 1.1lb/day more than the control
mob over the 60 day trial. The per-head
cost of the grain was 70c/day and the
additional carcase weight gain was worth
$1.40/day.
The amount of crop saved was surprising.
The control mob was consuming 20lb/
day of forage and 4lb/day of hay. The
supplement group (2lb/day wheat) only
consumed 13lb/day of forage – as they
used feed more efficiently.
Yearling Trial – Cereal crop grazing
Objective:
Compare the profitability of a group of
yearlings growing from 450lb to 1000lb,
grazing cereal crops against another
group on the same feed but with an
additional supplement of 4lb/day of 16%
protein pellets.
Result summary:
The average daily weight gain achieved
was 3.06lb, 1.34lb higher than the historic
average.
The average time to grow the steers from
450lb to target weight reduced from an
average of 315 days to only 182 days.
Yearling Trial – Pasture grazing
Objective:
Compare the profitability of a group of
yearlings growing from 650lb to 900lb,
grazing pasture against another group
on the same feed but with an additional
supplement of 3lb/day of barley.
Result summary:
The control group weight gain averaged
1.96lb/head/day. The Barley group weight
gain averaged 2.86lb/head/day, an extra
0.90lb/head/day. Barley consumption
averaged 2.51lb/head/day.
If barley is $0.10/lb and live weight gain is
$1.30lb, the added income amounted to
$1.17/day, the added expenses to $0.25/
day – an added profit of $0.92/head per
day. A herd of 200 yearlings, over 120
days would add $22,080 in profit.
COMPLETED ON-FARM TRIALS
3IN1FEEDERS 2015 Catalog 12
March 27-29: Cattle Raisers Convention, Fort Worth www.tscra.org/convention
April 16-18: Oklahoma City Farm Show www.oklahomacityfarmshow.com
May 7-10: Abilene Western Heritage Ranch Rodeo www.westernheritageclassic.com
November 6-9: Amarillo World Championship Ranch Rodeo www.wrca.org
December 1-3: Amarillo Farm and Ranch Show www.ideaggroup.com/amarillo
December 11-13: Tulsa Farm Show www.tulsafarmshow.com
UPCOMING SHOWS
Depending on your location and need for delivery, extra charges and taxes may apply.
FEEDER FORM PRICE EX. TAX
FLAT-PACKED $2180
3800ASSEMBLED $2330
FLAT-PACKED $1940
1800ASSEMBLED $2075
FLAT-PACKED $1080
800ASSEMBLED $1180
FLAT-PACKED $3900
MGF3800ASSEMBLED $4125
FLAT-PACKED $3020
MGF1800ASSEMBLED $3230
FLAT-PACKED $400
CG2ASSEMBLED $425
FLAT-PACKED $320
CG1ASSEMBLED $345
FLAT-PACKED N/A
MAASSEMBLED $195
One gate only
One gate only
One gate only
One gate only
DEALERS: Myrna and Marlin Huber
1-800-806-0715
EMAIL: [email protected]
3IN1FEEDERS have Pick Up Locations throughout the US.
Please call or visit our website for your nearest location.
PLEASE NOTE: Show dates are correct at time of printing. Please check our website for up-to-date details of all shows.