43678371 CATIA V5R18 Course Catalog

CATIA V5R18Course Material Catalog

March 2008 Edition

CATIA V5R18 Course Material Catalog Mar 11, 2008 1/101

CATIA V5R18 Course Material Catalog

CATIA Course Material .......................................................................... 5Analysis Solutions ................................................................................................ 5

EST: ELFINI Structural Analysis (EDU-CAT-E-EST-F - V5R18) ............................................. 6FMD: FEM Solid (EDU-CAT-E-FMD-F - V5R18) ..................................................................... 7FMS: FEM Surface (EDU-CAT-E-FMS-F - V5R18) ................................................................. 9GAS: Generative Assembly Structural Analysis (EDU-CAT-E-GAS-F - V5R18) ................... 11GDY: Generative Dynamic Response Analysis (EDU-CAT-E-GDY-F - V5R18) ................... 13GPE: Generative Part Structural Analysis Expert (EDU-CAT-E-GPE-F - V5R18) ................. 14GPF: Generative Part Structural Analysis Fundamental (EDU-CAT-E-GPF-F - V5R18) ...... 15TAA: Tolerance Analysis of Deformable Assembly (EDU-CAT-E-TAA-F - V5R18) .............. 16V5A: CATIA V5 for Analysis (EDU-CAT-E-V5A-F - V5R18) .................................................. 17

Equipment & Systems Engineering Solutions .................................................... 18CBD: Circuit Board Design (EDU-CAT-E-CBD-F - V5R18) ................................................... 19EC1: Electrical 3D Design and Documentation (EDU-CAT-E-EC1-F - V5R18) .................... 20EHF: Electical Harness Flattening (EDU-CAT-E-EHF-F - V5R18) ........................................ 21ELI: Electrical Librarian & Harness Installation (EDU-CAT-E-ELI-F - V5R18) ....................... 22EWR: Electrical Wire Routing (EDU-CAT-E-EWR-F - V5R18) .............................................. 24TUB: Tubing Design (EDU-CAT-E-TUB-F - V5R18) .............................................................. 25TUD: Tubing Diagrams (EDU-CAT-E-TUD-F - V5R18) ......................................................... 26TUS: Tubing Catalogs (2D Diagrams & 3D Design) (EDU-CAT-E-TUS-A - V5R18) ............. 27V5VE: CATIA V5 Automotive - Electrical (EDU-CAT-E-V5VE-F - V5R18) ............................ 28

Infrastructure Solutions ....................................................................................... 29ADM: V5 Administration (EDU-CAT-E-ADM-F - V5R18) ....................................................... 30DF1: Product Data Filtering (EDU-CAT-E-DF1-F - V5R18) ................................................... 31PHS: Photo Studio (EDU-CAT-E-PHS-F - V5R18) ................................................................ 32PRO: CATIA Tools for Proficient Users (EDU-CAT-E-PRO-F - V5R18) ................................ 33PSO: Photo Studio Optimizer (EDU-CAT-E-PSO-F - V5R18) ............................................... 34RTR: Real Time Rendering (EDU-CAT-E-RTR-F - V5R18) .................................................. 35V4A: V4/V5 Advanced Interoperability (EDU-CAT-E-V4A-A - V5R18) .................................. 36V4I: V4 Integration (EDU-CAT-E-V4I-F - V5R18) .................................................................. 37VBA: CATIA V5 Automation (EDU-CAT-E-VBA-F - V5R18) .................................................. 38

Mechanical Design Solutions .............................................................................. 39ASL: Aerospace Sheet Metal Design (EDU-CAT-E-ASL-F - V5R18) .................................... 40ASM: CATIA Product Design Expert (EDU-CAT-E-ASM-A - V5R18) .................................... 41CCV: Core & Cavity Design (EDU-CAT-E-CCV-F - V5R18) .................................................. 42DDR: CATIA Detail Drafting (EDU-CAT-E-DDR-F - V5R18) ................................................. 43DRA: Advanced Drafting & Customization (EDU-CAT-E-DRA-A - V5R18) ........................... 44FMP: Functional Molded Part (EDU-CAT-E-FMP-F - V5R18) ............................................... 45FR1: Part Design Feature Recognition (EDU-CAT-E-FR1-F - V5R18) ................................. 46FTA: 3D Functional Tolerancing & Annotation (EDU-CAT-E-FTA-F - V5R18) ...................... 47GS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R18) ................................................. 48


HA1: Healing Assistant (EDU-CAT-E-HA1-F - V5R18) ......................................................... 49LO1: 2D Layout for 3D Design (EDU-CAT-E-LO1-F - V5R18) .............................................. 50MD2: Mechanical Design V5R18 Update (EDU-CAT-E-MD2-U - V5R18) ............................. 51MTD: Mold Tooling Design (EDU-CAT-E-MTD-F - V5R18) ................................................... 52PDG: CATIA Part Design Expert (EDU-CAT-E-PDG-A - V5R18) ......................................... 53SMD: CATIA Generative Sheetmetal Design (EDU-CAT-E-SMD-F - V5R18) ....................... 54SMD: CATIA Generative Sheet Metal Design V5R18 Update (EDU-CAT-E-SMD-U - V5R18)SR1: Structure Design (EDU-CAT-E-SR1-F - V5R18) .......................................................... 57SRA: Structure Design Administration (EDU-CAT-E-SRA-A - V5R18) .................................. 59TG1: Tooling Design (EDU-CAT-E-TG1-F - V5R18) ............................................................. 60V5E: CATIA V5 Mechanical Design Expert (EDU-CAT-E-V5E-A - V5R18) .......................... 61V5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R18) .............................................. 62V5VB: V5 Automotive - Fundamental Course for Body Designers (EDU-CAT-E-V5VB-F - V5R18)V5VC: V5 Automotive - Fundamental Course for Chassis Designers (EDU-CAT-E-V5VC-F - V5R18)V5VP: V5 Automotive - Fundamental Course for Powertrain Designers (EDU-CAT-E-V5VP-F - V5R18)WD1: Weld Design (EDU-CAT-E-WD1-F - V5R18) ............................................................... 66

Machining Solutions ........................................................................................... 67AMG: Advanced Part Machining (EDU-CAT-E-AMG-F - V5R18) .......................................... 68LMG: Lathe Machining (EDU-CAT-E-LMG-F - V5R18) ......................................................... 69MLG: Multi-Slide Lathe Machining (EDU-CAT-E-MLG-F - V5R18) ....................................... 70MMG: Multi-Axis Surface Machining (EDU-CAT-E-MMG-F - V5R18) ................................... 71MPA: Prismatic Machining Preparation Assistant (EDU-CAT-E-MPA-F - V5R18) ................ 72MPG: Multi Pocket Machining (EDU-CAT-E-MPG-F - V5R18) .............................................. 73NCI: Numerical Control Infrastructure (EDU-CAT-E-NCI-F - V5R18) .................................... 74PMG: Prismatic Machining (EDU-CAT-E-PMG-F - V5R18) .................................................. 75SMG: Surface Machining (EDU-CAT-E-SMG-F - V5R18) ..................................................... 76STL: STL Rapid Prototyping (EDU-CAT-E-STL-F - V5R18) .................................................. 78

Product Synthesis Solutions ............................................................................... 79HMN: Human Modeling (EDU-CAT-E-HMN-F - V5R18) ........................................................ 80KBE: Knowledge-Based Engineering (EDU-CAT-E-KBE-F - V5R18) ................................... 81KBE: Knowledge-Based Engineering (EDU-CAT-E-KBE-A - V5R18) ................................... 82KWA: Knowledge Advisor (EDU-CAT-E-KWA-F - V5R18) .................................................... 83KWE: Knowledge Expert (EDU-CAT-E-KWE-F - V5R18) ..................................................... 84KWF: Knowledge Fundamentals (EDU-CAT-E-KWF-F - V5R18) ......................................... 85PEO: Product Engineering Optimizer (EDU-CAT-E-PEO-F - V5R18) ................................... 86

Shape Design & Styling Solutions ...................................................................... 87DL1: Developed Shapes (EDU-CAT-E-DL1-F - V5R18) ........................................................ 88DSE: Digitized Shape Editor (EDU-CAT-E-DSE-F - V5R18) ................................................. 89DSS: Shape Sculptor (EDU-CAT-E-DSS-F - V5R18) ............................................................ 90FSK: FreeStyle Sketch Tracer (EDU-CAT-E-FSK-F - V5R18) .............................................. 92FSS: FreeStyle Shaper, Optimizer & Profiler (EDU-CAT-E-FSS-F - V5R18) ........................ 93GSD: Surface Design Expert (EDU-CAT-E-GSD-F - V5R18) ............................................... 94


GSO: Generative Shape Optimizer (EDU-CAT-E-GSO-F - V5R18) ...................................... 95HD2: Generative Shape Design V5R18 Update (EDU-CAT-E-HD2-U - V5R18) ................... 97IMA: Imagine & Shape (EDU-CAT-E-IMA-F - V5R18) ........................................................... 98QSR: Quick Surface Reconstruction (EDU-CAT-E-QSR-F - V5R18) .................................... 99RSO: Realistic Shape Optimizer (EDU-CAT-E-RSO-F - V5R18) ........................................ 100V5S: V5 Surface Design (EDU-CAT-E-V5S-F - V5R18) ...................................................... 101


CATIA Course Material

Analysis Solutions

CATIA V5R18 Course Catalog Mar 11, 2008 5/101

AnalysisSolutions

EST: ELFINI Structural Analysis

EDU-CAT-E-EST-FCourse Code EDU-CAT-E-EST-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-EST-FI-V5R17 Foils: EDU-CAT-E-EST-FF-V5R17 Exercises: EDU-CAT-E-EST-FX-V5R17

ObjectivesUpon completion of this course you will be able to: - Use the advanced pre-processing capabilities (such as loads and boundaryconditions) to create more realistic FE models. - Visualize the images of objects used for pre-processing (which is not possiblein GPS). - Use advanced case features (such as Buckling, MultiLoads, Envelope) inaddition to the standard Static and Frequency cases - Create your own result image templates, customize the post-processing resultimages, group selective entitites in the result images, and create advancedreports

Participants' ProfileMechanical DesignersStructural Analysts

PrerequisitesGenerative Part Structural Analysis Fundamentals, Generative AssemblyStructural Analysis, FEM Surface Meshing

Content- Introduction to EST Analysis- Advanced Pre-Processing- Advanced Analysis Case Management- Advanced Post-Processing- Master Exercises- Added Exercises

ExercisesEx. 1: Advanced Analysis of Landing Gear Assembly (120min) / AerospaceEx. 2: Blade Analysis (120min) / Aerospace


AnalysisSolutions

FMD: FEM Solid

EDU-CAT-E-FMD-FCourse Code EDU-CAT-E-FMD-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMD-FI-V5R18 Foils: EDU-CAT-E-FMD-FF-V5R18 Exercises: EDU-CAT-E-FMD-FX-V5R18 Detailed Steps: EDU-CAT-E-FMD-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Use different solid meshers such as Tetrahedron Filler, OCTREE TetrahedronMesher, Sweep3D Mesher - Create a solid mesh using mesh part transformations like Translation,Rotation, and Symmetry on 3D mesh parts - Analyze the solid meshes using the available mesh quality criteria - Import/Export the meshes into/from CATIA

Participants' ProfileMechanical Designers

Prerequisites- Generative Part Structural Analysis Fundamentals- Generative Part Structural Analysis Expert- Generative Assembly Structural Analysis- FEM Surface Meshing


ContentThis course will teach you how to generate a 3D tetrahedron mesh by focusingon the transformation methods used to create new mesh models from anexisting 2D or 3D mesh. It will teach you how to analyze the quality of theresulting mesh and visualize internal mesh elements.

Introduction to FEM Solid- What is FEM Solid- User Interface- General Process for Solid Mesh Generation- Accessing the Workbench

Tetrahedron Filler- What is Tetrahedron Filler- Tetrahedron Filler Parameters- Generating Solid Mesh Using Tetrahedron Filler

OCTREE Tetrahedron Mesher- What is OCTREE Tetrahedron Mesher- OCTREE Tetrahedron Mesher - Local Parameters- OCTREE Tetrahedron mesher - Quality Parameters- OCTREE Tetrahedron mesher - Other Parameters- Generating Mesh Using OCTREE Tetrahedron Mesher

Sweep 3D- What is Sweep 3D- Generating Solid Mesh Using Sweep 3D

Mesh Part Transformations- What is Mesh Part Transformations- Solid Mesh Generation Using Translation- Solid Mesh Generation Using Rotation- Solid Mesh Generation Using Symmetry

Mesh Part Extrusion- What is Mesh Part Extrusion- Solid Mesh Generation Using Extrusion with Translation- Solid Mesh Generation Using Extrusion with Rotation- Solid Mesh Generation Using Extrusion with Symmetry- Solid Mesh Generation Using Extrusion along Spine

Mesh Analysis and Mesh Data Transfer- Quality Analysis- Cutting Plane Analysis- Import/Export Meshes

ExercisesEx. 1: OCTREE Tetrahedron Mesher (15min) / All sectorsEx. 2: Solid Meshing Using Sweep 3D (5min) / All sectorsEx. 3: Mesh Part Transformation (15min) / All sectorsEx. 4: Mesh Part Extrusion (15min) / All sectorsEx. 5: Master Exercise: Meshing of an Engine Cylinder Block (60min) / Allsectors


AnalysisSolutions

FMS: FEM Surface

EDU-CAT-E-FMS-FCourse Code EDU-CAT-E-FMS-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMS-FI-V5R18 Foils: EDU-CAT-E-FMS-FF-V5R18 Exercises: EDU-CAT-E-FMS-FX-V5R18 Detailed Steps: EDU-CAT-E-FMS-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Use the various Meshers such as Surface Mesher, Advanced SurfaceMesher, Beam Mesher, and OCTREE Triangle Mesher - Create a new mesh using existing mesh with the help of mesh transformationtools and mesh operators - Edit the mesh using the mesh edition tools available within the abovementioned meshers - Analyze the mesh quality using mesh quality checks and tools like FreeEdges, Duplicate Elements, Duplicate Nodes, Mesh Interference Checks, etc.


Prerequisites- Generative Part Structural Analysis Fundamentals- Generative Assembly Structural Analysis

ContentThis course will teach you how to create a FE model for a complex surfacepart, and how to simplify geometric data so as to optimize the meshingprocess. You will learn how to manage surface and beam meshes, modifymeshes and node distributions, and perform interference and quality checks.

- Introduction to FEM Surface- Advanced Surface Mesh- Surface Mesh- OCTREE Triangle Mesher- Mesh Operators- Mesh Transformations- Update Mesh- Mesh Analysis Tools- Import/Export Meshes- Welding Connections


ExercisesEx. 1: Floor Mesh (20min) / All sectorsEx. 2: Fuselage Door Static Analysis (30min) / All sectorsEx. 3: Surface Mesher (75min) / All sectorsEx. 4: Octree Mesh on Block Cylinder (15min) / All sectorsEx. 5: Hybrid Mesh: 1D and 2D (30min) / All sectorsEx. 6: Extrude 1D Element Into 2D Mesh (15min) / All sectorsEx. 7: Mesh Parameters Exposition to Knowledge (30min) / All sectorsEx. 8: Mesh Parameters Exposition to Knowledge 2 (10min) / All sectorsEx. 9: Mesh Parameters Exposition to Knowledge 3 (5min) / All sectorsEx. 10: Meshing Parametric Conceptual Body (60min) / All sectorsEx. 11: Seam Welding Analysis (60min) / All sectorsEx. 12: Compatible Seam Welds (30min) / All sectorsEx. 13: Spot Welding With Hemming (15min) / All sectorsEx. 14: Fuselage Connection (60min) / All sectorsEx. 15: Master Exercise 1: Meshing of a Crossmember (60min) / All sectorsEx. 16: Wing Structure Analysis (60min) / All sectors


AnalysisSolutions

GAS: Generative Assembly Structural Analysis

EDU-CAT-E-GAS-FCourse Code EDU-CAT-E-GAS-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GAS-FI-V5R18 Foils: EDU-CAT-E-GAS-FF-V5R18 Exercises: EDU-CAT-E-GAS-FX-V5R18 Detailed Steps: EDU-CAT-E-GAS-FS-V5R18

Objectives- Use different types of hypotheses for an assembly analysis- Define analysis connections between assembly components- Use existing assembly constraints to automatically create connections- Assign a connection property to the appropriate analysis connection- Compute a static analysis for an assembly- Create and manage an analysis assembly model from existing meshed parts


PrerequisitesGenerative Part Structural Analysis Fundamentals Generative Part Structural Analysis Expert


ContentThis course will teach you how to perform a Finite Element Analysis using anexisting assembly, and will focus on the creation of connections betweenassembly components and how to assign appropriate connection properties.You will also learn how to create an analysis assembly from existing meshedparts.

Introduction to GAS- What is Generative Assembly Structural Analysis-Assembly Analysis Overview-Analysis Assembly Overview-what is GAS-Hypotheses Used for Analysis

Analysis Connections-What is Analysis Connection-General Analysis Connection-Defining Line Analysis Connections-Defining Point Analysis Connections-Defining Surface Analysis Connections-Points to Points Analysis Connection

GAS Connections-Face Face Connection Properties-Distant Connection Properties-Welding Connection Properties-Nodes to Nodes Connection Property

Analysis Assembly Management-What is Analysis Assembly-Why Use Analysis Assembly-Analysis Assembly Process-What is Shape Representation-How to Attach Shape to Part-What is Analysis Assembly 2D Viewer-How to Use Analysis Assembly 2D Viewer

ExercisesNone


AnalysisSolutions

GDY: Generative Dynamic Response Analysis

EDU-CAT-E-GDY-FCourse Code EDU-CAT-E-GDY-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GDY-FI-V5R18 Foils: EDU-CAT-E-GDY-FF-V5R18 Exercises: EDU-CAT-E-GDY-FX-V5R18 Detailed Steps: EDU-CAT-E-GDY-FS-V5R18

Objectives- Recognize the differences between harmonic and transient analyses- Define load and restraint excitations- Ensure that the appropriate pre-requisites are defined for the requiredexcitation case- Visualize and animate 3D images of the analysis results- Generate translation, velocity and acceleration graphs- Export result data in Text or Excel format


PrerequisitesGenerative Part Structural Analysis Fundamentals Generative Part Structural Analysis Expert

ContentThis course will teach you how to perform a harmonic or transient analysis on asingle part using finite elements. You will learn how to generate and visualize2D graphical results and how to export the resulting data.

Introduction to GDY-What are the Different Types of Dynamic Analysis-Load or Restraint Excitation-Prerequisites

GDY Preprocessing-Harmonic Response Case-Transient Response Analysis

Results Visualization- Generating Images- Generating 2D Display

ExercisesNone


AnalysisSolutions

GPE: Generative Part Structural Analysis Expert

EDU-CAT-E-GPE-FCourse Code EDU-CAT-E-GPE-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPE-FI-V5R18 Foils: EDU-CAT-E-GPE-FF-V5R18 Exercises: EDU-CAT-E-GPE-FX-V5R18 Detailed Steps: EDU-CAT-E-GPE-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Define and customize material properties - Apply pressure, acceleration and force density loads; and define virtual parts - Apply pivot, ball-joint, and user-defined restraints - Compute a frequency analysis for a single part - Create planar sections with which to visualize internal result values - Compute and refine a mesh using adaptive meshing in order to achieve apre-defined accuracy


PrerequisitesCATIA V5 FundamentalsGenerative Part Structural Analysis Fundamentals

ContentThis course will focus on advanced Finite Element Analysis pre-processingtechniques and post-processing tools, including the concept of virtual parts toavoid excessive geometric modeling. It will teach you how to perform afrequency analysis on a single part, and the use of adaptive meshing toachieve pre-defined accuracy.

GPS Advanced Pre-Processing Tools- Advanced Pre-Processing Tools- Frequency Analysis

Computation- Computing a Frequency Case- Computing with Adaptivity- Historic of Computation

GPS Advanced post-Processing Tools- Results Visualization- Results Management- Refinement

ExercisesNone


AnalysisSolutions

GPF: Generative Part Structural AnalysisFundamental

EDU-CAT-E-GPF-FCourse Code EDU-CAT-E-GPF-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPF-FI-V5R18 Foils: EDU-CAT-E-GPF-FF-V5R18 Exercises: EDU-CAT-E-GPF-FX-V5R18 Detailed Steps: EDU-CAT-E-GPF-FS-V5R18

ObjectivesThis course covers the main tools for Structural Analysis on a single part.Throughout this course, you will learn how to perform a basic static analysisusing the finite elements method.

Participants' ProfileCATIA Designers

PrerequisitesCATIA V5 Fundamentals

ContentIntroduction to Finite Element Analysis- What is Finite Element Analysis- Why to Use Finite Element Analysis- Application of Finite Element Analysis

Introduction to GPS Analysis- Accessing the Generative Part Structural Analysis Workbench- The Generative Part Structural Analysis Interface- The GPS General Process- The Generative Part Structural Analysis Tree Structure

GPS Pre-Processing- Managing Mesh-Part- Defining Restraints- Defining Loads

Computation- Specifying the External Storage- Computing a Static Case

GPS Post-Processing - Results Visualization- Results Management- Refinement

Managing Analysis- About Saving an Analysis Document- About Save As- How to Use Save Management- Saving Document Using ‘Send To’ Mechanism- User Settings

Notes

ExercisesNone


AnalysisSolutions

TAA: Tolerance Analysis of Deformable Assembly

EDU-CAT-E-TAA-FCourse Code EDU-CAT-E-TAA-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-TAA-FI-V5R17 Foils: EDU-CAT-E-TAA-FF-V5R17 Exercises: EDU-CAT-E-TAA-FX-V5R17

ObjectivesUpon completion of this course you will, Set up, compute and visualize a simple tolerance analysis of flexibleassemblies in CATIA V5. This course is an overview of Tolerance Analysis of Deformable Assembly(TAA) product.

Participants' ProfileMechanical Engineer, Tolerancing Engineer, FEM Analyst, ManufacturingEngineer.

PrerequisitesProduct Structure, Part Design, Assembly Design, Generative Shape Design,Functional Tolerancing & Annotations, Generative Part Structural AnalysisFundamentals, Generative Part Structural Analysis Expert, FEM SurfaceMeshing, FEM Solid Meshing, Generative Assembly Structural Analysis.

Content- Introduction to TAA- Creating Tolerance Analysis Elements- Tolerance Analysis- Frequently Asked Questions- Master Exercise- To Sum Up

ExercisesEx. 1: Interactive Tolerance analysis : Application (480min) / Aerospace,Automotive, Shipbuilding


AnalysisSolutions

V5A: CATIA V5 for Analysis

EDU-CAT-E-V5A-FCourse Code EDU-CAT-E-V5A-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5A-FI-V5R18 Foils: EDU-CAT-E-V5A-FF-V5R18

ObjectivesThis course is designed using a process-based approach to training. Ratherthan focusing on individual features and functions, this course emphasizes onthe processes and procedures required to complete a particular task. By usingthe case studies to illustrate these processes, you will learn the necessarycommands, options, and menus within the context of completing a design task.

Participants' ProfileNew CATIA V5 mechanical designers

PrerequisitesStudents attending this course should have the following experience:- Mechanical design experience- CATIA Basics

Content- Introduction to Finite Element Analysis- Pre-processing- Computation- Post-processing- Mesh refinement- Assembly Structural Analysis

ExercisesEx. 1: Introducation to Finite Element Analsyis (130min) / All sectorsEx. 2: Pre-processing (90min) / All sectorsEx. 3: Computation (45min) / All sectorsEx. 4: Post-processing (45min) / All sectorsEx. 5: Mesh Refinement (15min) / All sectorsEx. 6: Assembly Structural Analysis (60min) / All sectorsEx. 7: Master Project (120min) / All sectors



Equipment & Systems Engineering Solutions


Equipment & SystemsEngineering

Solutions

CBD: Circuit Board Design

EDU-CAT-E-CBD-FCourse Code EDU-CAT-E-CBD-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-CBD-FI-V5R17 Foils: EDU-CAT-E-CBD-FF-V5R17 Exercises: EDU-CAT-E-CBD-FX-V5R17 Detailed Steps: EDU-CAT-E-CBD-FS-V5R17

ObjectivesUpon completion of this course you will be able to create Printed Circuit Boards(PCB) in context of Assemblies and export/import them to/from an ECAD toolusing the IDF interface.

Participants' ProfileElectrical Designers

PrerequisitesStudents attending this course should have the knowledge of CATIA V5Fundamentals, Part Design, Assembly Design

Content- Introduction to Circuit Board Design- Creating the PCB geometry with Mounting Holes- Constraint Areas and Components- Export and Import using the IDF Interface- Creating a Catalog of Electrical Components- To Sum Up- Master Exercise: Connector Box- Added Exercise: Camera

ExercisesEx. 1: Transformer (45min) / Electronics & ElectricalEx. 2: Connector Box (40min) / Electronics & ElectricalEx. 3: Camera (30min) / Electronics & Electrical



Solutions

EC1: Electrical 3D Design and Documentation

EDU-CAT-E-EC1-FCourse Code EDU-CAT-E-EC1-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-EC1-FI-V5R18 Foils: EDU-CAT-E-EC1-FF-V5R18 Exercises: EDU-CAT-E-EC1-FX-V5R18

ObjectivesUpon completion of this course you will be able to:- Create the harness suitable for the consumer goods- Design the wire harness for appliances- Route the signal and create the wires- Flatten and synchronize an electrical or geometrical harness- Generate harness documentation- Generate simple drawings

Participants' ProfileConsumer goods Electrical Harness Designers

PrerequisitesMechanical Design conceptsKnowledge of Part Design, Assembly Design and Drafting workbenches

Content- Electrical Design and Documentation- Creating Electrical Components Library- Creating and Managing the Harness- Wire Routing- Harness Flattening- Drawing Introduction

What is new in this releaseNew course

ExercisesEx. 1: Defining Electrical Components / All sectorsEx. 2: Creating an Electrical Parts Catalog / All sectorsEx. 3: Creating an Electrical Assembly / All sectorsEx. 4: Bundle Segment Definition / All sectorsEx. 5: Split a Bundle Segment / All sectorsEx. 6: External Data Exchange for Wire Routing / All sectorsEx. 7: Extracting Harness / All sectorsEx. 8: Manipulating the Harness / All sectorsEx. 9: Synchronizing the Harness / All sectors



Solutions

EHF: Electical Harness Flattening

EDU-CAT-E-EHF-FCourse Code EDU-CAT-E-EHF-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EHF-FI-V5R18 Foils: EDU-CAT-E-EHF-FF-V5R18 Exercises: EDU-CAT-E-EHF-FX-V5R18

ObjectivesIn this course you will learn how to flatten an electrical or geometrical harnessintegrated within the DMU and how to modify the bundle segments of theharness to fit your drawing in order to build the harness documentation

Participants' ProfileElectrical V5 users

PrerequisitesPRO-F: CATIA Tools for Proficient UsersEHI-F: Electrical Harness InstallationELB-F: Electrical Librarian

ContentIntroduction to Harness FlatteningHarness Flattening parametersExtracting dataHarness flattening modificationsSynchronizeLinks visualizationReportsDrawingCatalog text template creationGraphic Replacement

ExercisesEx. 1: Harness Documentation / Electronics & ElectricalEx. 2: Harness Flattening / Electronics & ElectricalEx. 3: Harness Documentation (2) / Electronics & ElectricalEx. 4: Harness Flattening (2) / Electronics & Electrical



Solutions

ELI: Electrical Librarian & Harness Installation

EDU-CAT-E-ELI-FCourse Code EDU-CAT-E-ELI-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ELI-FI-V5R18 Foils: EDU-CAT-E-ELI-FF-V5R18 Exercises: EDU-CAT-E-ELI-FX-V5R18

ObjectivesIn this course you will learn how to build and manage an electrical componentscatalog, to design a harness integrated within the DMU and then connect thebundle segments to electrical components.

Participants' ProfileNew Electrical V5 users

PrerequisitesCatalog Editorart DesignCATIA V5 basics (mandatory)

ContentIntroduction to Electrical LibrarianElectrical Componentas DefinitionElectrical Librarian Catalog ManagementElectrical AssembliesIntroduction to Electrical Harness InstallationElectrical Harness SettingsGeometric Bundle definitionPosition Electrical DevicesBundle segment DefinitionManaging a Branch PointDelete BranchSplit a Bundle segmentTransfer BranchesInstantiate a protectionAdjust DiameterLinks ManagementLocal slack managementSupport ManagementMeasure geometrical bundle inertiaV4/V5 MigrationWires ManagementImporting electrical external data for 3D implementation


ExercisesEx. 1: Creating a catalog (10min) / All sectorsEx. 2: Defining a set of electrical components (40min) / All sectorsEx. 3: Store components in a catalog (15min) / All sectorsEx. 4: Define an assembly with the components from the catalog (15min) / AllsectorsEx. 5: Create a protection and store it into a catalog (15min) / All sectorsEx. 6: Bundle Segment Definition (15min) / All sectorsEx. 7: Create an adaptative support and position Bundle Segment (30min) / AllsectorsEx. 8: Link a bundle segment (10min) / All sectorsEx. 9: Add a Support to a Bundle Segment (5min) / All sectorsEx. 10: Add Local Slack to Bundle Segment portion (5min) / All sectorsEx. 11: Manage the bundle segment section (30min) / All sectorsEx. 12: Transfer Branches (15min) / All sectorsEx. 13: Instantiate a Protection (15min) / All sectorsEx. 14: Adjusts Diameter (10min) / All sectorsEx. 15: Split a Bundle Segment (10min) / All sectorsEx. 16: Define a Bundle Segment (20min) / All sectorsEx. 17: Harness Design / All sectorsEx. 18: Geometrical bundle inertia / All sectorsEx. 19: Knowledge (20min) / All sectorsEx. 20: External Data (30min) / All sectorsEx. 21: Electrical Harness installation / All sectorsEx. 22: Car Door / All sectors



Solutions

EWR: Electrical Wire Routing

EDU-CAT-E-EWR-FCourse Code EDU-CAT-E-EWR-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EWR-FI-V5R18 Foils: EDU-CAT-E-EWR-FF-V5R18 Exercises: EDU-CAT-E-EWR-FX-V5R18

ObjectivesAt the end of this course, participants will be able to:- Route wires in a harness.- Route signals in space reservation system- Use knowledgeware for segregation rules

Participants' ProfileNew V5 CATIA electrical users

PrerequisitesCATIA V5 Part DesignCATIA V5 Assembly Design

ContentIntroduction to Electrical Wire RoutingImport External DataWires Management

ExercisesEx. 1: External Data Exchange (60min) / All sectorsEx. 2: External Data (60min) / All sectorsEx. 3: External Data Exchange (60min) / All sectors



Solutions

TUB: Tubing Design

EDU-CAT-E-TUB-FCourse Code EDU-CAT-E-TUB-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUB-FI-V5R18 Foils: EDU-CAT-E-TUB-FF-V5R18 Exercises: EDU-CAT-E-TUB-FX-V5R18

ObjectivesIn this course you will learn how the CATIA Tubing Design product is used toquickly and efficiently create an intelligent tubing layout.

Participants' ProfileExperienced CATIA V5 users


Content- Introduction to Tubing Design- Tubing Design Fundamentals- Modifying Tubing Designs- Managing Tubing Designs- Added Functionalities

ExercisesNone



Solutions

TUD: Tubing Diagrams

EDU-CAT-E-TUD-FCourse Code EDU-CAT-E-TUD-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUD-FI-V5R18 Foils: EDU-CAT-E-TUD-FF-V5R18 Exercises: EDU-CAT-E-TUD-FX-V5R18

ObjectivesThis course illustrates how the Tubing Diagram product could be used toquickly and efficiently create a schematic diagram.

Participants' ProfileExperienced CATIA V5 Users


Content- Introduction- Tubing Diagram Creation - Diagram Modification/Annotation/Reports- Design Checks- Analysis

ExercisesNone



Solutions

TUS: Tubing Catalogs (2D Diagrams & 3D Design)

EDU-CAT-E-TUS-ACourse Code EDU-CAT-E-TUS-ACATIA V5R18Brand & Release CATIA V5R184 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUS-AI-V5R18 Foils: EDU-CAT-E-TUS-AF-V5R18 Exercises: EDU-CAT-E-TUS-AX-V5R18 Detailed Steps: EDU-CAT-E-TUS-AS-V5R18

ObjectivesUpon completion of this course you will be able to: - Manage object classes in the Feature Dictionary - Create 2D Diagram Catalogs and 3D Design Catalogs - Create Standards Catalogs, Design Rules Catalogs - Create Reports - Customize the settings for Drawings


PrerequisitesCATIA V5 Fundamentals- Tubing Design- Tubing Diagrams- ESA

Content- Introduction to Tubing Catalogs- Tubing Workbench Customization- Creating a Report- Drawing Production Settings

ExercisesNone



Solutions

V5VE: CATIA V5 Automotive - Electrical

EDU-CAT-E-V5VE-FCourse Code EDU-CAT-E-V5VE-FCATIA V5R18Brand & Release CATIA V5R186 daysDuration 6 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5VE-FI-V5R18 Foils: EDU-CAT-E-V5VE-FF-V5R18

ObjectivesThe aim of the course is to teach you how to build parts and assemblies inCATIA and hwo to make simple drawings of these parts and assemblies. Thiscourse also teaches you to create a library of electrical parts, instantiateelectrical devices from a catalog, route electrical harness in your digitalmock-up, route wires in the harness, extract harness and create harnessdrawings.

Participants' ProfileAutomotive Electrical Harness DesignersNew Electrical V5 Users

PrerequisitesExperience in Mechanical Design

Content- Introduction to CATIA- Profile Creation- Basic Features- Assembly Design- Designing in Context- Drafting (ISO)- Introduction to Electrical Library Products- Creating Electrical Harness- Routing Electrical Wires- Flattening Electrical Harness- Creating Electrical Harness Documentation


ExercisesEx. 1: Master Project: V5 Automotive Electrical / All sectors



Infrastructure Solutions


InfrastructureSolutions

ADM: V5 Administration

EDU-CAT-E-ADM-FCourse Code EDU-CAT-E-ADM-FCATIA V5R18Brand & Release CATIA V5R183 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-ADM-FI-V5R18 Foils: EDU-CAT-E-ADM-FF-V5R18 Exercises: EDU-CAT-E-ADM-FX-V5R18

ObjectivesThis course tells you how to install, customize and maintain CATIA V5 site

Participants' ProfileAdministrators of CATIA V5

Prerequisites- System Administration - CATIA Administration

Content- CATIA Installation- Licensing- Environment Management- Settings Management- Standards- Software Management- Tools- Data Managment- Interoperability

ExercisesNone



DF1: Product Data Filtering

EDU-CAT-E-DF1-FCourse Code EDU-CAT-E-DF1-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DF1-FI-V5R18 Foils: EDU-CAT-E-DF1-FF-V5R18 Exercises: EDU-CAT-E-DF1-FX-V5R18

ObjectivesIn the course you will learn how to use Product Data Filtering (DF1) to convertparts or products to datum surfaces and solids. The main objective of filtering is to hide the design process by removing allintermediate objects and associativity links. Another goal might be simply toreduce the size of models.

Participants' ProfileAll designers

PrerequisitesMechanical or hybrid design.

ContentIntroduction to Product Data Filtering- Why do you need DF1 ?Workbench presentation- Accessing the workbenchData Filtering - Filter a Part- Filter a Product

ExercisesEx. 1: Part (15min) / All sectorsEx. 2: Product (15min) / All sectors



PHS: Photo Studio

EDU-CAT-E-PHS-FCourse Code EDU-CAT-E-PHS-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PHS-FI-V5R18 Foils: EDU-CAT-E-PHS-FF-V5R18 Exercises: EDU-CAT-E-PHS-FX-V5R18 Detailed Steps: EDU-CAT-E-PHS-FS-V5R18

ObjectivesObjectives of the Course

Upon completion of this course you will be able to: - Create photo realistic images using the Photo Studio workbench - Create and apply stickers to your models - Create animations using different techniques

Participants' ProfileIndustrial Stylists and Designers


Content- Introduction- Environment management- Camera management- Light sources management- Shooting management- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements- Catalogs

ExercisesEx. 1: Phone Handset (150min) / Fabrication & Assemblies Consumer Goods



PRO: CATIA Tools for Proficient Users

EDU-CAT-E-PRO-FCourse Code EDU-CAT-E-PRO-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PRO-FI-V5R18 Foils: EDU-CAT-E-PRO-FF-V5R18

ObjectivesUpon completion of this course you will be able to:-Create and reuse advanced replication tools like Power Copies-Store components and Power copies into catalog and reuse them in a newcontext-Analyze and convert CATIA V4 models to CATIA V5

Participants' ProfileAdvanced Users

PrerequisitesStudents attending this course should have knowledge of CATIA BASICS andPart Design

ContentThis course will teach you how to use advanced CATIA tools to re-use existingCATIA V4 and CATIA V5 model data. You will learn how to make use ofcomponent catalogs, and how to store and create re-usable parameterizedfeatures.

- Creating and Using Power Copy- Creating Catalogs of Components- From CATIA V4 to V5 Basics- Course Summary

ExercisesNone



PSO: Photo Studio Optimizer

EDU-CAT-E-PSO-FCourse Code EDU-CAT-E-PSO-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PSO-FI-V5R18 Foils: EDU-CAT-E-PSO-FF-V5R18

ObjectivesUpon completion of this course you will be able to use the various Photo StudioOptimizer tools to enhance the quality of your photo realistic images.


PrerequisitesCATIA V5 FundamentalsCATIA Photo Studio

Content- 3D textures- Bump mapping- Global illumination- Caustics- Visual effects

ExercisesNone



RTR: Real Time Rendering

EDU-CAT-E-RTR-FCourse Code EDU-CAT-E-RTR-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-RTR-FI-V5R18 Foils: EDU-CAT-E-RTR-FF-V5R18 Exercises: EDU-CAT-E-RTR-FX-V5R18

ObjectivesUpon completion of this course you will be able to: - Create the required environment around a model - Apply materials, textures, and 3D textures to your models - Use different types of lights and cameras to create the desired ambience



Content- Introduction- Environment management- Camera management- Light sources management- DMU integration- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements

ExercisesEx. 1: Defining an Environment (5min) / AutomotiveEx. 2: Defining the Camera (10min) / All sectorsEx. 3: Defining the Light Source (10min) / AutomotiveEx. 4: Applying Texture (40min) / AutomotiveEx. 5: Applying Stickers (10min) / AutomotiveEx. 6: Creating an Animation Using a Turntable (15min) / AutomotiveEx. 7: Creating an Animation of Scene (15min) / Automotive



V4A: V4/V5 Advanced Interoperability

EDU-CAT-E-V4A-ACourse Code EDU-CAT-E-V4A-ACATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4A-AI-V5R18 Foils: EDU-CAT-E-V4A-AF-V5R18 Exercises: EDU-CAT-E-V4A-AX-V5R18

ObjectivesIn this course, you will learn advanced interoperability concepts about themigration of CATIA V4 geometric/application data to CATIA V5. You will alsolearn how V5 data can be saved in CATIA V4 formats or used directly in CATIAV4.

Participants' ProfileExperienced CATIA V4/V5 users

PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- From V4 to V5 - Transfer of V4 geometric data to V5 - Transfer of V4 application data to V5- From V5 to V4 - Using V5 data in V4 - Saving V5 data in V4 formats

ExercisesEx. 1: Smart/Unsmart Solid (15min) / All sectorsEx. 2: Error during update (15min) / All sectorsEx. 3: Migration of kinematics data (25min) / All sectorsEx. 4: Sheet Metal Design (10min) / All sectors



V4I: V4 Integration

EDU-CAT-E-V4I-FCourse Code EDU-CAT-E-V4I-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4I-FI-V5R18 Foils: EDU-CAT-E-V4I-FF-V5R18 Exercises: EDU-CAT-E-V4I-FX-V5R18 Detailed Steps: EDU-CAT-E-V4I-FS-V5R18 Demonstration: EDU-CAT-E-V4I-FD-V5R18

ObjectivesAt the end of this course, participants will be able to:- Use CATIA V4 data in CATIA V5- Transfer a CATIA V4 solid into a CATIA V5 CATPart- Manage the links between CATIA V4 and CATIA V5 documents

Participants' ProfileCATIA V5 users

PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- Introduction to V4 Integration- Creating a CATProduct using V4 data- Assembly of V4 data in a V5 CATProduct- Transferring V4 data into V5 CATPart- Design in context- Drawing of a V4/V5 document in V5- Migration of 2D Draw elements and Views- CATIA V5 DMU solutions and V4 data- Links between V4 data and V5 documents

ExercisesEx. 1: Recap Exercise 1 : open and check the V4 geometry (20min) / AllsectorsEx. 2: Recap Exercise 2 : Solid translation (15min) / All sectorsEx. 3: Recap Exercise 3 : manipulations in a CATProduct (20min) / All sectorsEx. 4: Welding Gun : Creating a CATProduct with V4 data (10min) / All sectorsEx. 5: Welding Gun : Assembly of V4 data in a V5 CATProduct (15min) / AllsectorsEx. 6: Welding Gun : Copy/Pasting a V4 solid in a V5 CATPart (20min) / AllsectorsEx. 7: Welding Gun : Design in context (20min) / All sectorsEx. 8: Welding Gun : Generative drafting (20min) / All sectorsEx. 9: Welding Gun : DMU Space Analysis (20min) / All sectorsEx. 10: Welding Gun : V4 Modification and Update in V5 (20min) / All sectors



VBA: CATIA V5 Automation

EDU-CAT-E-VBA-FCourse Code EDU-CAT-E-VBA-FCATIA V5R18Brand & Release CATIA V5R184 daysDuration 4 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesFoils: EDU-CAT-E-VBA-FF-V5R18 Instructor Foils: EDU-CAT-E-VBA-FI-V5R18 Exercises: EDU-CAT-E-VBA-FX-V5R18

ObjectivesAt the end of this course, participants will have a good understanding of thedifferent ways to automate tasks related to CATIA V5: CATIA Macros andVisual Basic Programming.

Participants' ProfileCATIA V5 Applications developers; bench markers

PrerequisitesCATIA V5 Fundamentals.Visual Basic Editor on PC NTMinimum knowledge or exposure to Microsoft Visual Basic (cf. book ref.Microsoft Visual Basic 6.0 Learning Edition)JavaScript is a plus

Content- CATIA V5 OLE Automation, Journaling & Scripting Architecture- Exported objects of CATIA V5- Designing panels for Macros- Graphic selection of objects- Settings - V5 Administration - Communication with another Automation server.

ExercisesEx. 1: Cylinders (Master Exercise) (10min) / All sectorsEx. 2: Modifying the viewpoint of an existing document (30min) / All sectorsEx. 3: Creating 2D sketch with constraints (15min) / All sectorsEx. 4: Creating part design features (30min) / All sectorsEx. 5: Creating 3D wireframes and 3D surfaces (30min) / All sectorsEx. 6: Titanic (30min) / All sectorsEx. 7: Drafting the bolt (30min) / All sectorsEx. 8: Test Selections (30min) / All sectorsEx. 9: Select Element (30min) / All sectorsEx. 10: Get Point (30min) / All sectorsEx. 11: Settings - Applying local changes (20min) / All sectors



Mechanical Design Solutions


Mechanical DesignSolutions

ASL: Aerospace Sheet Metal Design

EDU-CAT-E-ASL-FCourse Code EDU-CAT-E-ASL-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASL-FI-V5R18 Foils: EDU-CAT-E-ASL-FF-V5R18 Exercises: EDU-CAT-E-ASL-FX-V5R18 Detailed Steps: EDU-CAT-E-ASL-FS-V5R18

ObjectivesIn this course, you will learn how to generate sheet metal parts for aerospace

Participants' ProfileAerospace Airframe Designer

PrerequisitesPart Design, Assembly Design, Wireframe and Surface Design

Content- Introduction to Aerospace Sheet Metal Design- ASL Parameters- Creating the Web- Creating a Surfacic Flange- Creating a Joggle- Creating Flanges- Creating a Corner Relief - Creating a Cut Out- Creating Stamps - Flanged Hole - Bead - Circular Stamp - Surface Stamp - Flanged Cutout - Stiffening Rib - Curve Stamp - User Stamp- Creating a Hole- Points or Curves Mapping- Creating Corners or Chamfers- Applying a Pattern- Modifying a Feature- Generating Folded and Flattened Parts- Drawing Generation

ExercisesEx. 1: Fighter Airframe (50min) / All sectorsEx. 2: Aero Structure (30min) / All sectorsEx. 3: Bracket (15min) / All sectorsEx. 4: Fighter Web Structure (20min) / All sectorsEx. 5: Rib (20min) / All sectors



ASM: CATIA Product Design Expert

EDU-CAT-E-ASM-ACourse Code EDU-CAT-E-ASM-ACATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASM-AI-V5R18 Foils: EDU-CAT-E-ASM-AF-V5R18 Exercises: EDU-CAT-E-ASM-AX-V5R18

ObjectivesUpon completion of this course, you will be able to:-Modify CATIA options in order to optimize performance for large, complexdesigns-Manage contextual links between product documents by using publications-create and use parameters to drive a product designCreate sections to visualize internal product structure-Create scenes and explodes views-Generate annotations and bills of material for assembly drawings


PrerequisitesStudents attending this course should have the knowledge of CATIA ProductDesign, CATIA Part Design.

ContentThis course will teach you collaborative engineering methods with which youcan design parts in the context of a complex product structure. You will learnhow to optimize performance for large and complex designs, and how togenerate annotations and bills of material for assembly drawings.

- Managing a Product Structure- Designing & Managing Contextual Parts- Creating and Using Published Geometry- Flexible Sub-Assembly- Working with Large Assemblies- Analyzing Assemblies to Prepare drawing

ExercisesNone



CCV: Core & Cavity Design

EDU-CAT-E-CCV-FCourse Code EDU-CAT-E-CCV-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesFoils: EDU-CAT-E-CCV-FF-V5R18 Exercises: EDU-CAT-E-CCV-FX-V5R18 Detailed Steps: EDU-CAT-E-CCV-FS-V5R18

ObjectivesUpon completion of the course you will be able to: - Import the part to a mold - Define the main pulling direction - Update mold areas by transferring, splitting and segregating faces - Create a parting surface - Use functionalities dedicated to stamping - Perform a geometric comparison of two parts

Participants' ProfileSurface designers in tooling domain

PrerequisitesV5F-F: CATIA V5 Fundamentals

Content- Import the Part to mold- Define the Main Pulling Direction- Define a Slider/Lifter Pulling Direction- Work on Mold Areas : Transfer, Aggregate, Split, Explode, Bounding Box- Define Parting Surface

ExercisesEx. 1: Pan Handle (60min) / All sectorsEx. 2: Support (30min) / All sectors



DDR: CATIA Detail Drafting

EDU-CAT-E-DDR-FCourse Code EDU-CAT-E-DDR-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DDR-FI-V5R18 Foils: EDU-CAT-E-DDR-FF-V5R18 Exercises: EDU-CAT-E-DDR-FX-V5R18

ObjectivesUpon completion of this course, you will be able to:-Create an interactive view and draw a sketch on it-Insert annotations to dress-up the views-Use advanced dimensioning toolsYou will also be introduced to the 2D-3D links management and to the draftingworkbench customization

Participants' ProfileDraftsmen

PrerequisitesStudents attending this course should be familiar with the basics of 2D viewscreation in CATIA V5

Content- Introduction to drafting workbench- Creating Interactive Views- Dressing up the Layout- View and Sheet Management- Customizing the Drafting Workbench- Master Exercise

What is new in this releaseThis course has been reworked to focus on the interactive creation and dressup of views. It includes useful recommendations and introduces to the use of2D components from catalogs.

ExercisesNone



DRA: Advanced Drafting & Customization

EDU-CAT-E-DRA-ACourse Code EDU-CAT-E-DRA-ACATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DRA-AI-V5R18 Foils: EDU-CAT-E-DRA-AF-V5R18 Exercises: EDU-CAT-E-DRA-AX-V5R18

ObjectivesUpon completion of this course you will be able to set and manage alldimension and annotation standards contained in the standard files accordingto company or projects needs.

Participants' ProfileDraftsmen, Drafting Administrators

PrerequisitesCATIA V5 Mechanical Design Fundamentals, knowledge of VB scripting

ContentDuring this 2-day session you will see -Hints & Tips on Interactive Drafting-Hints & Tips on Generative Drafting-Drawing Generation of large assemblies-Administration tasks-Increasing Productivity-Creating Frames & Title Blocks with a macro

ExercisesNone



FMP: Functional Molded Part

EDU-CAT-E-FMP-FCourse Code EDU-CAT-E-FMP-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMP-FI-V5R18 Foils: EDU-CAT-E-FMP-FF-V5R18 Exercises: EDU-CAT-E-FMP-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:- Define the main shapes of a molded part as added or removed material- Add functional features such as ribs or cutouts to the part- Finalize the molded part using the feature modifiers such as fillets or patterns- Use the multi-body approach- Extract cores and cavities from the final part

Participants' ProfileMold Designers

PrerequisitesStudents attending this course should be familiar with CATIA V5Fundamentals.

ContentThis course will teach you how to use the Functional Molded Part workbench tocreate molded parts from the main shapes definition and to finalize the partwith additional dress up features. You will also be taught the multi-bodyapproach and will finally learn how to extract cores and cavity from the finalpart.

- Basics of functional Molded Parts- Basic Features- Functional Features- Feature Modifiers and Dress-Up Tools- Multi-Body Features- Extraction Features

ExercisesNone



FR1: Part Design Feature Recognition

EDU-CAT-E-FR1-FCourse Code EDU-CAT-E-FR1-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FR1-FI-V5R18 Foils: EDU-CAT-E-FR1-FF-V5R18 Exercises: EDU-CAT-E-FR1-FX-V5R18

ObjectivesUpon completion of this course you will be able to: - Build comprehensive V5 data structures for solids whose specifications arelost or unreachable - Build data structure for solids that have been imported from other CADsystems


PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals and CATIA Part Design.

ContentFeature Recognition: IntroductionPerforming Feature RecognitionMaster ExerciseTo Sum Up

ExercisesEx. 1: Creating V5 geometry from an isolated solid (30min) / All sectors



FTA: 3D Functional Tolerancing & Annotation

EDU-CAT-E-FTA-FCourse Code EDU-CAT-E-FTA-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FTA-FI-V5R18 Foils: EDU-CAT-E-FTA-FF-V5R18 Exercises: EDU-CAT-E-FTA-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:- Add 3D annotations to a part- Manage and position these annotations- Create and manage annotation planes and views- Manage the 3D geometry associated to the 3D annotations


PrerequisitesStudents attending this course should be familiar with the basics of solids andsurfaces creation and also with the basics of knowledge

ContentThis course will teach you how to create annotation planes in a CATPart andhow to add and manage 3D annotations on these planes. You will also learnhow to create 3D views in the CATPart and how to use them to create 2Dviews in a CATDrawing.

ExercisesNone



GS1: CATIA Surface Design

EDU-CAT-E-GS1-FCourse Code EDU-CAT-E-GS1-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GS1-FI-V5R18 Foils: EDU-CAT-E-GS1-FF-V5R18 Exercises: EDU-CAT-E-GS1-FX-V5R18

ObjectivesUpon completion of this course you will be able to:- Identify and use the tools specific to the Generative Shape Design workbench- Create simple reference and Wireframe geometry- Use the reference wireframe elements to create simple surfaces- Create clean topology from a set of surfaces and smooth sharp edges- Detect and correct the discontinuities on curves and surfaces- Create solids from surfaces

Participants' ProfileMechanical Surface Designers

PrerequisitesStudents attending this course should be familiar with the CATIA V5 interface

ContentThis course introduces you to the Generative Shape Design interface andbasic tools. You will be taught wireframe and surface creation and you will familiarizeyourself with the hybrid design. This course focus on the Generative Shape Design tools that are available witha MD2 license.

- Introduction to Surface Design- Creating Wireframe Geometry- Shape Design Common Tools- Creating Surfaces- Performing Operations on the Geometry- Completing the Geometry in Part Design- Modifying the Geometry- Using Tools-Master Exercice: Mobile Phone

ExercisesNone



HA1: Healing Assistant

EDU-CAT-E-HA1-FCourse Code EDU-CAT-E-HA1-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-HA1-FI-V5R18 Foils: EDU-CAT-E-HA1-FF-V5R18 Exercises: EDU-CAT-E-HA1-FX-V5R18

ObjectivesUpon completion of this course you will be able to: - Analyze the imported data - Repair the imported data - Compare two versions of a Part - Customize the workbench

Participants' ProfileAll designers, especially in the tooling design domain

PrerequisitesGS1-F-V5R16: CATIA Surface Design

Content - Introduction to Healing Assistant - Master Exercise Presentation - Model Analysis - Master Exercise Step 1: Topological Analysis - Closing a Join Surface - Master Exercise Step 2: Topological Healing - Comparing Models - Customizing the Workbench

ExercisesEx. 1: Lateral Fender (master exercise) (60min) / All sectorsEx. 2: Compare exercise: Lateral fender (30min) / All sectorsEx. 3: Additional exercise (Handle) (45min) / All sectors



LO1: 2D Layout for 3D Design

EDU-CAT-E-LO1-FCourse Code EDU-CAT-E-LO1-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-LO1-FI-V5R18 Foils: EDU-CAT-E-LO1-FF-V5R18 Exercises: EDU-CAT-E-LO1-FX-V5R18

ObjectivesIn this course you will learn how to draw benefit from 2D & 3D available in asingle environment to design 3D products.


PrerequisitesDraftingPart DesignAssembly Design

Content1- Introduction Accessing the Workbench User Interface General Presentation User Settings Standards2- Geometry Creation Creating Projection Views Exporting the 2D View to 2D Layout Using 2D Components 3D Visualization and Use-Edges Capabilities Managing the Background Visualization Dressing-up the Geometry Creating 3D geometry from 2D geometry3- Data Management Print Capabilities Drawing Creation from 2D Layout

ExercisesNone



MD2: Mechanical Design V5R18 Update

EDU-CAT-E-MD2-UCourse Code EDU-CAT-E-MD2-UCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MD2-UI-V5R18 Foils: EDU-CAT-E-MD2-UF-V5R18

ObjectivesUpon completion of this course you will be able to use the new and enhancedtools of the Mechanical Design Workbenches in V5R18 Release.


PrerequisitesStudents attending this course should have knowledge of CATIA MechanicalDesign V5R17

ContentThis course will teach you the principal new tools available in CATIA V5R18Mechanical Design. You will be taught the new options for variable radiuscreation. You will also learn how to create symmetric set in products, how touse tolerant modeling while creating blends. In the drafting workbench, you willsee how to create new 2D and 3D clipping views or how to customize symbols.

- Sketcher Updates- Part Design Updates - Assembly Design Updates- Generative Shape Design.

ExercisesNone



MTD: Mold Tooling Design

EDU-CAT-E-MTD-FCourse Code EDU-CAT-E-MTD-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MTD-FI-V5R18 Foils: EDU-CAT-E-MTD-FF-V5R18 Exercises: EDU-CAT-E-MTD-FX-V5R18 Detailed Steps: EDU-CAT-E-MTD-FS-V5R18

ObjectivesUpon Completion of this course you will be able to: - Create the mold base having guided and fixed components using MoldTooling Design workbench - Build the complete assembly of a Plastic Injection Mold.

Participants' ProfileNew Mold Tooling Design users

PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals and TG1 Tooling Design Fundamentals

ContentIntroduction to Mold Tooling DesignCreating a New MoldEditing the Mold Base Working with Mold ComponentsMold Design to ManufacturingCreating Injection Features Additional Information

ExercisesNone



PDG: CATIA Part Design Expert

EDU-CAT-E-PDG-ACourse Code EDU-CAT-E-PDG-ACATIA V5R18Brand & Release CATIA V5R181.5 daysDuration 1.5 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PDG-AI-V5R18 Foils: EDU-CAT-E-PDG-AF-V5R18 Exercises: EDU-CAT-E-PDG-AX-V5R18

ObjectivesUpon completion of this course, you will be able to:-Use 3D reference Elements to create a part-Create advanced Sketch-Based Features-Apply Advanced Dress-Up Features-Design using Boolean operations-Share Designs by working in Multi-Model environment-Analyse Parts-Annotate Parts for review

Participants' ProfileCATIA V5 Mechanical Designers.

PrerequisitesStudents attending this course should have the knowledge of CATIA V5Fundamentals, Getting started with CATIA V5, Sketcher, Part DesignFundamentals

ContentThis course will teach you to design ‘Complex’ 3D mechanical parts fromsketches in context of an assembly. You will build upon the knowledge gainedin the Part Design Course and will be equiped to use ‘Advanced’ featuresoffered by the Part Design workbench.

- Using 3D Elements to Create a Part- Sketch-Based Features- Part Manipulations- Dress-Up Features- Part Analysis- Annotations

ExercisesNone



SMD: CATIA Generative Sheetmetal Design

EDU-CAT-E-SMD-FCourse Code EDU-CAT-E-SMD-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMD-FI-V5R18 Foils: EDU-CAT-E-SMD-FF-V5R18 Exercises: EDU-CAT-E-SMD-FX-V5R18 Detailed Steps: EDU-CAT-E-SMD-FS-V5R18

ObjectivesUnderstand the terminology and the creation process for sheet metal partdesignDefine and manage sheet metal part parametersDesign walls, bends and flanges- Add features such as cutouts, holes, corners and chamfers - Create standard and user defined stamped features- Manage folded and unfolded views and export a finished flat pattern

Participants' ProfileMechanical Designers, Sheetmetal Designers

PrerequisitesCATIA V5 Fundamentals.


ContentThis course will teach you how to design a sheet metal part using associativefeature-based modeling. Standard and user defined stamped features can beintegrated into the design and the resulting flat pattern is calculated inaccordance with standard bend allowances or with company specific bendallowance tables.

Getting Started- Introduction to Sheet Metal Design- Generative Sheet Metal Design Overview- Defining Sheet Metal Parameters- Recommendations for Getting Started

Sheet Metal Walls - What is a Sheet Metal Wall?- Defining the First Wall- Secondary Walls- Part Recognition- Recommendations for Sheet Metal Walls

Bends and Unfolded Mode- Bends- Unfolded Mode- Corner Relief- Recommendations for Bends

Flanges- Creating Flanges- Recommendations for Flanges

Sheet Metal Features- Cutouts- Holes- Corners and Chamfers- Standard Stamps- User-Defined Stamps- Recommendations for Sheet Metal Features

Transformations and Duplication - Transformation of Parts- Patterns- Mirror- PowerCopies- Recommendations for Duplication

Mapping and Output- Point or Curve Mapping- Output

Advanced Topics in Sheet Metal- Sheet Metal Standard Files- Multi-Body Methodology

ExercisesNone



SMD: CATIA Generative Sheet Metal Design V5R18Update

EDU-CAT-E-SMD-UCourse Code EDU-CAT-E-SMD-UCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMD-UI-V5R18 Foils: EDU-CAT-E-SMD-UF-V5R18

ObjectivesUpon completion of this course you will be able to use the new and enhancedcapabilities of Generative Sheetmetal Design Workbench in V5R18 release.


PrerequisitesStudents attending this course must have knowledge of CATIA GenerativeSheetmetal Design V5R17.

Content-Enhancements in Wall-Enhancements in Extrusion-Enhancements in Hopper-Transformation of Parts-Enhancements in Local Unfolding

ExercisesNone



SR1: Structure Design

EDU-CAT-E-SR1-FCourse Code EDU-CAT-E-SR1-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SR1-FI-V5R18 Foils: EDU-CAT-E-SR1-FF-V5R18 Exercises: EDU-CAT-E-SR1-FX-V5R18 Additional Information: EDU-CAT-E-SR1-FO-V5R18

ObjectivesIn this course you will learn methods to quickly create and modify linear andcurved structures, and plates using standard or user-defined sections. Itaddresses any kind of Frames, Foundations and Steel construction …, invarious domains like Aerospace, Automotive and F&A.

Participants' ProfileNew CATIA V5 users

PrerequisitesCOM, WFS, PDG


Content1.Introduction to Structure Designp6 Accessing the Workbench p7 Exploring the User Interfacep8 Terminologyp92.Options & Project Resources Managementp10 Setting Structure Design Optionsp11 Setting Part Design Options p12 Setting Assembly Design Optionsp14 Selecting a Projectp153.Creating Skeletonsp17 What about Skeletons?p18 Creating Grids in 3Dp194.Defining and Creating Shapes & Platesp22 What about Shapes? p23 Generating Piece Parts p24 Defining & Placing Shapes… p26 Defining Material & Gradep27 Defining Section p28 Defining Shape Anchor Point p29 Defining Shape Orientation p30 Placing Shapes Using Points p31 Placing Shapes on Support p34 Creating Plates & End-Platesp36 Creating Small Assemblies p425.Modifying Shapes & Platesp44 Modifying Shapes & Plates Definition p45 Extending and Stretching Shapesp47 Splitting and Merging Shapes & Platesp48 Nibbling/Coping Shapes ans Platesp49 Defining Cutbacks p51 Removing Cutbacks p57 Placing Cutoutsp58 Modifying Cutouts p63 Removing Cutouts p64 Placing End Cuts p65 Modifying and Removing End Cuts p69 Placing Slotsp70 Modifying Slotsp74 Removing Slotsp75

ExercisesEx. 1: Select your project and options (15min) / All sectorsEx. 2: External Turret: Panel System (45min) / All sectorsEx. 3: External Turret: Jacket System (30min) / All sectorsEx. 4: External Turret: Floor System (30min) / All sectorsEx. 5: External Turret: Detailing (90min) / All sectorsEx. 6: External Turret: Modifications (15min) / All sectorsEx. 7: External Turret: Secondary Structures (30min) / All sectorsEx. 8: Piece Part Generation (30min) / All sectors



SRA: Structure Design Administration

EDU-CAT-E-SRA-ACourse Code EDU-CAT-E-SRA-ACATIA V5R18Brand & Release CATIA V5R184 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SRA-AI-V5R18 Foils: EDU-CAT-E-SRA-AF-V5R18 Exercises: EDU-CAT-E-SRA-AX-V5R18 Additional Information: EDU-CAT-E-SRA-AO-V5R18

ObjectivesIn this course you will learn methods to:- administrate a SR1 project.- Create or modify a Section Catalog- Create End-Cuts, Slots and Small Assmblies

Participants' ProfileExperienced CATIA V5 users

PrerequisitesCOM, WFS, PDG, SR1, PKT, KWA (Optional)

Content1. Project Resource Managementp5 Introducing the PRMp6 Understanding the PRMp7 Structure Discipline Resourcesp11 Accessing & Checking the PRM p152. Feature Dictionaryp16 About the Feature Dictionaryp17 Starting the Feature Dictionary Editorp18 Managing Attributes p19 Discrete Valuesp21 Managing ID Numberp223. Standard Section Catalogsp24 Managing Parametric Sectionsp25 Generating Resolved Partsp30 Creating/Modifying Standard Section Catalogsp32 Creating/Modifying the StructureSpecificationMaterial Catalogsp344. Detailing Featuresp41 Design Rules and Recommendationsp42 End-Cutsp45 Slotsp51 Small Assembliesp54 Storing Detailing Features in a catalogp57

ExercisesEx. 1: Creating a New Project (180min) / All sectorsEx. 2: Adding New Attributes (180min) / All sectorsEx. 3: Creating a Resolved Standard section (240min) / All sectorsEx. 4: Modifying the StructureSpecifiactionMaterial Catalog (240min) / AllsectorsEx. 5: Creating a Standard End-Cut (180min) / All sectorsEx. 6: Creating a Contextual End-Cut (180min) / All sectorsEx. 7: Creating a Slot (180min) / All sectorsEx. 8: Creating a Small Assembly (180min) / All sectors



TG1: Tooling Design

EDU-CAT-E-TG1-FCourse Code EDU-CAT-E-TG1-FCATIA V5R18Brand & Release CATIA V5R181.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesFoils: EDU-CAT-E-TG1-FF-V5R18 Exercises: EDU-CAT-E-TG1-FX-V5R18 Detailed Steps: EDU-CAT-E-TG1-FS-V5R18

ObjectivesUpon completion of this course you will be able to:Create the die and mold components using Mold Tool Design workbench.Instantiate the components in a die or mold structure.

Participants' ProfileNew Tooling Design users

PrerequisitesStudents attending this course should have experience in the followingdomain(s): CATIA V5 Fundamentals

ContentIntroduction to Tooling DesignCreating ComponentsEditing ComponentsSpecific Components : Inserts & SlidersAdvanced Add/Remove CapabilitiesManaging User ComponentsTool Design to Manufacturing

ExercisesNone



V5E: CATIA V5 Mechanical Design Expert

EDU-CAT-E-V5E-ACourse Code EDU-CAT-E-V5E-ACATIA V5R18Brand & Release CATIA V5R185 daysDuration 5 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5E-AI-V5R18 Foils: EDU-CAT-E-V5E-AF-V5R18

Objectives- Create a complex model in CATIA V5- Create and manage a structured model- Design parts in the context of an assembly- Re-use existing data to complete assemblies- Manage relationships between assembled parts- Analyze and annotate your design

Participants' ProfileMechanical designers already having an experience of CATIA V5 mechanicaldesign foundations.

PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals

ContentThis course will teach you how to start a complex design project from itsspecifications (top down approach) and complete it by reusing existing data. Itwill focus on advanced skills and concepts that enable you to create andanalyze complex parts and assemblies.

Lesson 1: IntroductionLesson 2: Design Complex PartsLesson 3: Surface DesignLesson 4: Analyze and Annotate PartsLesson 5: Sharing InformationLesson 6: Assembly DesignLesson 7: Design in ContextLesson 8: Complex Assembly DesignMaster Project 1: Mobile PhoneMaster Project 2: Lifting Truck

ExercisesNone



V5F: CATIA V5 Fundamentals

EDU-CAT-E-V5F-FCourse Code EDU-CAT-E-V5F-FCATIA V5R18Brand & Release CATIA V5R185 daysDuration 5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5F-FI-V5R18 Foils: EDU-CAT-E-V5F-FF-V5R18

ObjectivesUnderstand the CATIA V5 interface Plan the construction of a part in order to properly convey its visual andfunctional aspects Create simple parts in CATIA V5 Understand how to manage parts in the context of an assembly Produce simple drawings and assembly layouts

Participants' ProfileNew CATIA V5 Mechanical Designers

PrerequisitesMechanical design experience.Experience with the Windows operating system.

ContentThis course will introduce you to CATIA V5. It will teach you how to buildsimple parts and assemblies in CATIA, and how to make simple drawings ofthose parts and assemblies.

- Lesson 1: Introduction to CATIA- Lesson 2: Profile Creation

- Lesson 3: Basic Features

- Lesson 4: Additional Features

- Lesson 5: Dress-Up Features

- Lesson 6: Reusing Data

- Lesson 7: Finalizing Design Intent

- Lesson 8: Assembly Design

- Lesson 9: Design in Context

- Lesson 10: Drafting ISO

- Lesson 10: Drafting ANSI

ExercisesNone



V5VB: V5 Automotive - Fundamental Course for BodyDesigners

EDU-CAT-E-V5VB-FCourse Code EDU-CAT-E-V5VB-FCATIA V5R18Brand & Release CATIA V5R187 daysDuration 7 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5VB-FI-V5R18 Foils: EDU-CAT-E-V5VB-FF-V5R18

ObjectivesThis course will introduce the fundamental concepts that are required to buildsimple automotive parts and assemblies in CATIA V5, and teaches how tomake simple drawings of those parts and assemblies. It will introduce you tothe correct surface modeling methodology necessary for body or chassisdesign.

At the end of the course students will be able to:- Understand the CATIA V5 interface- Plan the construction of an automotive part in order to properly convey itsvisual and functional aspects- Create simple automotive parts in CATIA V5- Use correct surface modeling methodology for body or chassis design- Understand how to design and manage parts in the context of an assembly- Produce simple drawings and assembly layouts

Participants' ProfileAutomotive Chassis or Body Designers

PrerequisitesNone

ContentThis course is made up of 12 lessons.

-Lesson 1: Introduction to CATIA-Lesson 2: Profile Creation-Lesson 3: Basic Features-Lesson 4: Additional Features-Lesson 5: Dress-Up Features-Lesson 6: Reusing Data-Lesson 7: Create Simple Surface-Lesson 8: Create Complex Surfaces-Lesson 9: Surface Modification Tools-Lesson 10: Assembly Design-Lesson 11: Designing in Context-Lesson 12: Drafting (ISO)

ExercisesNone



V5VC: V5 Automotive - Fundamental Course forChassis Designers

EDU-CAT-E-V5VC-FCourse Code EDU-CAT-E-V5VC-FCATIA V5R18Brand & Release CATIA V5R187 daysDuration 7 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesNone

ObjectivesThis course will introduce the fundamental concepts that are required to buildsimple automotive parts and assemblies in CATIA V5, and teaches how tomake simple drawings of those parts and assemblies. It will introduce you tothe correct surface modeling methodology necessary for body or chassisdesign.

At the end of the course students will be able to:- Understand the CATIA V5 interface- Plan the construction of an automotive part in order to properly convey itsvisual and functional aspects- Create simple automotive parts in CATIA V5- Use correct surface modeling methodology for body or chassis design- Understand how to design and manage parts in the context of an assembly- Produce simple drawings and assembly layouts

Participants' ProfileAutomotive Chassis or Body Designers

PrerequisitesNone

ContentThis course is made up of 12 lessons.

Lessons 1- 6: Introduction to basic modeling in CATIA V5Lessons 7 - 9: Surface Modeling for Chassis / Body DesignLessons 10 - 11: Assembly DesignLessons 12: DraftingMaste Project

ExercisesNone



V5VP: V5 Automotive - Fundamental Course forPowertrain Designers

EDU-CAT-E-V5VP-FCourse Code EDU-CAT-E-V5VP-FCATIA V5R18Brand & Release CATIA V5R187 daysDuration 7 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesNone

ObjectivesThis course will introduce the fundamental concepts that are required to buildsimple automotive parts and assemblies in CATIA V5, and teaches how tomake simple drawings of those parts and assemblies. It will introduce you tothe advanced solid modeling techniques necessary for Powertrain designmethodology.

ContentThis course is made up of 12 lessons:Lessons 1 - 6:Introduction to basic Solid ModelingLessons 7 - 9: Complex Solid ModelingLessons 10 - 11: Assembly DesignLesson 12: DraftingMaster Project

ExercisesNone



WD1: Weld Design

EDU-CAT-E-WD1-FCourse Code EDU-CAT-E-WD1-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-WD1-FI-V5R18 Foils: EDU-CAT-E-WD1-FF-V5R18 Exercises: EDU-CAT-E-WD1-FX-V5R18

ObjectivesUpon completion of this course you will be able to - Weld parts, - Generate Weld reports, - Extract 2D views from 3D welds.

Participants' ProfileMechanical and Structural Designers


Content- Workbench presentation- Weld creation- Weld edition- Weld report and drawing

Complete industrial exercice

ExercisesEx. 1: Welding / All sectors



Machining Solutions


MachiningSolutions

AMG: Advanced Part Machining

EDU-CAT-E-AMG-FCourse Code EDU-CAT-E-AMG-FCATIA V5R18Brand & Release CATIA V5R181.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-AMG-FI-V5R18 Foils: EDU-CAT-E-AMG-FF-V5R18 Exercises: EDU-CAT-E-AMG-FX-V5R18

ObjectivesUpon completion of this course you will be able to:- Identify and use the Advance Part Machining workbench tools- Define a Multi-Axis Flank Contouring operation- Define a Multi-Axis Helix Machining operation Define a Cavities Roughing operation�

Participants' ProfileAdvanced NC Programmers

PrerequisitesStudents attending this course should have knowledge of Numerical ControlInfrastructure(NCI), PMG, SMG and MMG workbench.

Content- Multi Axis Flank Contouring operation presentation- Geometry tab- Strategy tab- Multi Axis Helix machining operation presentation- Geometry tab- Strategy tab- Cavities Roughing operation presentation- Geometry tab- Strategy tab

ExercisesNone


MachiningSolutions

LMG: Lathe Machining

EDU-CAT-E-LMG-FCourse Code EDU-CAT-E-LMG-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-LMG-FI-V5R18 Foils: EDU-CAT-E-LMG-FF-V5R18 Exercises: EDU-CAT-E-LMG-FX-V5R18

ObjectivesUpon completion of this course you will be able to:-Identify and use the Lathe Machining workbench tools-Define Lathe Machining operations-Manage Tools and Tool Assemblies-Use different methodologies for Lathe Machining

Participants' ProfileNC Programmers

PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals and Numerical Control Infrastructure workbench

Content-Introduction to Lathe Machining-Crankshaft:Master Exercise Presentation-Crankshaft (Step:1)-Lathe Operation-Rough Turning Operation-Crankshaft (Step:2)-Groove Turning Operation-Crankshaft (Step:3)-Recess Turning Operation-Crankshaft (Step:4)-Groove Finish Turning Operation-Profile Finish Turning Operation-Crankshaft (Step:5)-Thread Turning Operation-Crankshaft (Step:6)-Sequential Turning Operation-Crankshaft (Step:7)-Ramp Rough Turning Operation-Ramp Recess Turning Operation-Tools and Tool Assemblies Management-Methodologies for Lathe Machining-Added Exercises

ExercisesNone


MachiningSolutions

MLG: Multi-Slide Lathe Machining

EDU-CAT-E-MLG-FCourse Code EDU-CAT-E-MLG-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MLG-FI-V5R17 Foils: EDU-CAT-E-MLG-FF-V5R17 Exercises: EDU-CAT-E-MLG-FX-V5R17

ObjectivesUpon completion of this course you will learn how to program with CATIA V5Multi turret & Multi spindle machines.

Participants' ProfileNC programmer who wants to optimize the NC Program in a Multi turretMachine environment

PrerequisitesStudents attending this course must have knowledge of CATIA V5Fundamentals, NC Infrastructure, Lathe Machining

Content- Introduction to Multi- Slide Lathe Machining- Machine Definition- Master Exercise: Turning Part- Create Manufacturing Programs- Create Synchronizations- Gantt Chart View- Step 2: Organize your Program and Create Synchronizations- Time Based Replay- NC Outputs- Step 3: Replay operations and generate NC Code- Create the NC Programs- Added Exercise: Turning Part

ExercisesEx. 1: Define Multi Axis turning machine (30min) / All sectorsEx. 2: Organize your Program & create synchronizations (30min) / All sectorsEx. 3: Replay operations and generate NC Code (60min) / All sectorsEx. 4: Multi spindle machining (90min) / All sectors


MachiningSolutions

MMG: Multi-Axis Surface Machining

EDU-CAT-E-MMG-FCourse Code EDU-CAT-E-MMG-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MMG-FI-V5R18 Foils: EDU-CAT-E-MMG-FF-V5R18 Exercises: EDU-CAT-E-MMG-FX-V5R18

ObjectivesUpon completion of this course you will be able to - Identify and use the Multi-Axis Surface Machining workbench tools. - Define 5-Axis machining operations such as Multi-Axis Sweeping, Multi-AxisContour Driven, Multi-Axis Curve Machining, Define Multi-Axis IsoparametricMachining, Multi-Axis Drilling and Multi-Axis Tube Machining.

Participants' ProfileAdvanced NC Programmers

PrerequisitesStudents attending this course should have knowledge of CATIA V5 SMGFundamentals

Content- Multi-Axis Sweeping Operation- Multi-Axis Contour Driven Operation- Multi-Axis Curve Machining Operation- Multi-Axis Isoparametric Machining Operation- Multi-Axis Drilling Operation- Multi-Axis Tube Machining Operation

ExercisesNone


MachiningSolutions

MPA: Prismatic Machining Preparation Assistant

EDU-CAT-E-MPA-FCourse Code EDU-CAT-E-MPA-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPA-FI-V5R18 Foils: EDU-CAT-E-MPA-FF-V5R18 Exercises: EDU-CAT-E-MPA-FX-V5R18 Detailed Steps: EDU-CAT-E-MPA-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Define 2.5 Axis Milling operations in CATIA V5 - Create prismatic machinable features - Form a link between Design and Manufacturing


PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals, Numerical Control Infrastructure, Prismatic Machining

Content- Introduction to Prismatic Machining Preparation Assistant- Global features recognition- Locall features recognition

ExercisesNone


MachiningSolutions

MPG: Multi Pocket Machining

EDU-CAT-E-MPG-FCourse Code EDU-CAT-E-MPG-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPG-FI-V5R18 Foils: EDU-CAT-E-MPG-FF-V5R18 Exercises: EDU-CAT-E-MPG-FX-V5R18

ObjectivesIn this course, you will learn how to define a power Machining operation

Participants' ProfileNC programmer knowing how to work with CATIA V5 Parts and already skilledin Machining products.

PrerequisitesFundamentals about CATIA V5Numerical Control Infrastructure

Content- Introduction to Multi- Pockets Machining- Power Machining: Geometry- Power Machining: Strategy- Managing Offsets

ExercisesNone


MachiningSolutions

NCI: Numerical Control Infrastructure

EDU-CAT-E-NCI-FCourse Code EDU-CAT-E-NCI-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-NCI-FI-V5R18 Foils: EDU-CAT-E-NCI-FF-V5R18 Exercises: EDU-CAT-E-NCI-FX-V5R18 Detailed Steps: EDU-CAT-E-NCI-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Identify and use the tools specific to Manufacturing workbenches - Create a Manufacturing Program and simulate it - Manage Tools and Tool Catalogs - Define and verify the Tool Path - Generate NC data using an integrated Post Processor - Create shop floor documentation - Manage design changes - Import V4 data

Participants' ProfileManufacturing Users (NC Programmers)


ContentCOMMON TOPICSLesson 1 : Workbench PresentationLesson 2 : Define Setup (Part Operation)Lesson 3 : Machining Operation, Macros, Tools PresentationLesson 4 : Tool Path Verification & Simulationlesson 5 : Auto sequencelesson 6 : Auxiliary Operationslesson 7 : Output generationlesson 8 : Axial Operationslesson 9 : Hole selection - Machining Pattern Managementlesson 10 : The different Process ViewsLesson 11 : Geometry wizard (edge, surface)

ADVANCED TOPICSLesson 12 : Import & Modify Tool PathLesson 13 : Resource ManagementLesson 14 : PP Word Table customizationLesson 15 : V4 NCMill & NCLathe Set Import (optional)Lesson 16 : Design Change ManagementLesson 17 : Machining Processes

APPENDIXSettings

ExercisesNone


MachiningSolutions

PMG: Prismatic Machining

EDU-CAT-E-PMG-FCourse Code EDU-CAT-E-PMG-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-PMG-FI-V5R18 Foils: EDU-CAT-E-PMG-FF-V5R18 Exercises: EDU-CAT-E-PMG-FX-V5R18 Detailed Steps: EDU-CAT-E-PMG-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Identify and use the Prismatic Machining workbench tools - Define Prismatic Machining operations (2.5 Axis Milling) in CATIA V5 - Create Prismatic Machining Area and Rework Area - Define and modify NC Macros


PrerequisitesCATIA V5 FundamentalsNumerical Control Infrastructure

ContentMilling operations: - Facing,- Pocketing, - Prismatic Roughing,- Profile contouring,- Groove milling,- Point to point, - Curve following, - Prismatic rework area,- Prismatic machining area,- Transition Paths (macros)

ExercisesNone


MachiningSolutions

SMG: Surface Machining

EDU-CAT-E-SMG-FCourse Code EDU-CAT-E-SMG-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMG-FI-V5R18 Foils: EDU-CAT-E-SMG-FF-V5R18 Exercises: EDU-CAT-E-SMG-FX-V5R18 Detailed Steps: EDU-CAT-E-SMG-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Identify and use the Surface Machining workbench tools - Define 3-Axis Surface Machining operations - Create a Machining Area before performing the operations - Define a Rework Area - Analyze and modify the Tool Path

Participants' ProfileManufacturing users (NC programmers)

Prerequisites- CATIA V5 Fundamentals- Numerical Control Infrastructure


ContentIntroduction to the 3-Axis Surface Machining Accessing the Workbench Workbench the user interface Process/Product/Resources model Manufacturing terminology General process

Creating geometrical elements Creates rough stock Inserts an STL file Creates a stock by offset Points creation wizard Limit lines projection wizard Limit lines creation wizard

Creating a Machining Feature Geometrical Zone Creation Machining/Slope Area Creation Rework Area Creation Offset group Creation

Creating a 3-Axis Surface Machining Operation 3-Axis Machining Operations Sweep Roughing Operation Roughing Operation Sweeping Operation Pencil Operation Zlevel Operation Contour-driven Operation Isoparametric machining Operation Spiral milling Operation Profile Contouring Operation

Analysing and modifying tool path

NotesThis course is linked to NCI course.

ExercisesNone


MachiningSolutions

STL: STL Rapid Prototyping

EDU-CAT-E-STL-FCourse Code EDU-CAT-E-STL-FCATIA V5R18Brand & Release CATIA V5R180.3 dayDuration 0.3 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-STL-FI-V5R18 Foils: EDU-CAT-E-STL-FF-V5R18 Exercises: EDU-CAT-E-STL-FX-V5R18

ObjectivesIn this course you will learn how to - Create a triangular mesh from a surface or a solid - Correct, tune, improve a triangular mesh, - Export a mesh as a standard STL file usable for rapid prototyping bystereolithography or any other prototyping technique (FDM, classical 3 axismilling)

Participants' ProfileSurface Designer

PrerequisitesDSE-F: Digitized Shape Editor

Content- Introduction- Creating a mesh from a basic surface- Tuning the mesh- Giving a thickness to the mesh- Optimizing the mesh- Exporting the mesh as an STL file

ExercisesNone



Product Synthesis Solutions


Product SynthesisSolutions

HMN: Human Modeling

EDU-CAT-E-HMN-FCourse Code EDU-CAT-E-HMN-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-HMN-FI-V5R18 Foils: EDU-CAT-E-HMN-FF-V5R18 Exercises: EDU-CAT-E-HMN-FX-V5R18 Detailed Steps: EDU-CAT-E-HMN-FS-V5R18

ObjectivesIn this course, you will learn how to use our Human Model technology in orderto leverage your ergonomics analysis. Among other things, you will learn howto position and manipulate the manikins within a V5 scene. In addition, you willevaluate the comfort, the reach, clearance, and the vision of your targetpopulation. Additional to standard ergonomics analysis you will evaluateinteraction between the manikin and geometries in the scene. Finally, you willrealize a simulation (animation).

Participants' Profile- Designers- Engineers- Human factors specialists- Any Health specialist

PrerequisitesCourse on Digital mock-up

ContentYou will use the Ergonomics Design & Analysis tools to review the ergonomicsaspect of a manikin inside and around a vehicle, with the tools of theworkbenches: Human Builder, Human Measurement Editor, Human ActivityAnalysis and Human Postural Analysis.

ExercisesEx. 1: Ergonomics review inside a vehicle with Human Measurement Editor(240min) / AutomotiveEx. 2: Ergonomics review inside a vehicle with Human Postural Analysis(240min) / AutomotiveEx. 3: Ergonomics review around a vehicle with Human Activity Analysis(240min) / AutomotiveEx. 4: Ergonomics review inside a vehicle with Human Builder (240min) /Automotive



KBE: Knowledge-Based Engineering

EDU-CAT-E-KBE-FCourse Code EDU-CAT-E-KBE-FCATIA V5R18Brand & Release CATIA V5R183 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KBE-FI-V5R18 Foils: EDU-CAT-E-KBE-FF-V5R18 Exercises: EDU-CAT-E-KBE-FX-V5R18 Detailed Steps: EDU-CAT-E-KBE-FS-V5R18

ObjectivesUpon completion of this course you will be able to:- Become familiar with the knowledgeware working environment, how it can beaccessed, the terminology that will be used and the settings- Create parametric parts and assemblies- Embed knowledge in your designs by controlling it using parameters,formulae, rules, checks and reactions- Create and reuse Power Copies and User-Defined Features- Create and store knowledge-driven design templates so as to instantiatethem in a new context- Create and reuse advanced instantiation features like Knowledge Pattern

Participants' ProfileCATIA V5 Users


Content- Introduction- Knowledge Advisor Workbench Presentation- Creating parameters, Formulas and Lists- Creating Adaptive Behaviors- Creating Design Tables and Part Families- Using Knowledge Advisor Tools- Product Knowledge Template Workbench Presentation- Creating and Using Powercopies- Creating and Using User-defined Features- Creating and Using Part and Assembly Templates- Managing Standard Components- Creating and Using Knowledge Patterns


ExercisesEx. 1: Stringer / All sectorsEx. 2: Knowledge Advisor / All sectorsEx. 3: Keyway / All sectorsEx. 4: User-defined Features / All sectorsEx. 5: Document Templates / All sectorsEx. 6: Jigs and Fixtures / All sectors



KBE: Knowledge-Based Engineering

EDU-CAT-E-KBE-ACourse Code EDU-CAT-E-KBE-ACATIA V5R18Brand & Release CATIA V5R181.5 daysDuration 1.5 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KBE-AI-V5R18 Foils: EDU-CAT-E-KBE-AF-V5R18 Exercises: EDU-CAT-E-KBE-AX-V5R18 Detailed Steps: EDU-CAT-E-KBE-AS-V5R18

ObjectivesUpon completion of this course you will be able to:- Become familiar with the knowledgeware working environment, the way it canbe accessed, the terminology that will be used and the settings- Embed complex design knowledge in a parametric part using knowledgewareexpert rules, checks and reactions- Automate your design modifications using various knowledgeware experttools- Define, solve and analyze an optimization problem using tools from theCATIA Product Knowledge Engineering workbench

Participants' ProfileCATIA V5 Advanced Users

PrerequisitesCATIA V5 BasicsCATIA V5 Knowledgeware Fundamentals

Content- Introduction to Knowledge Expert- Creating and Using an Expert Rule- Creating and Analyzing an Expert Check- Creating a Rule Base- Product Engineering Optimizer Workbench Presentation- Optimization Problem Formulation- Optimization Problem Resolution- Solution Analysis- Best Practices for Optimization with PEO- Design of Experiments Tools- Constraint Satisfaction Tools


ExercisesEx. 1: Connector / All sectorsEx. 2: LBlock / All sectorsEx. 3: Strap Tension Optimization / All sectorsEx. 4: Bottle / All sectorsEx. 5: Beam Mass Optimization / All sectorsEx. 6: Hanger / All sectorsEx. 7: Fastener / All sectorsEx. 8: Surfacic Structure / All sectorsEx. 9: 1D Beam / All sectorsEx. 10: Silo / All sectorsEx. 11: Design of Experiments / All sectors



KWA: Knowledge Advisor

EDU-CAT-E-KWA-FCourse Code EDU-CAT-E-KWA-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWA-FI-V5R18 Foils: EDU-CAT-E-KWA-FF-V5R18 Exercises: EDU-CAT-E-KWA-FX-V5R18 Detailed Steps: EDU-CAT-E-KWA-FS-V5R18

ObjectivesAccess the Knowledgeware working environmentCreate user parameters and formulaeCreate Design Tables and use them to create part familiesCreate reaction features that react to an event such as an updateUse the Macro with Argument featureUse inspection, equations, law and loop tools


PrerequisitesCATIA V5 Basics

ContentThis course you will teach you how to manage Knowledge Advisor objects inorder to embed knowledge within a design. It will teach you how to useknowledge rules to reduce errors and automate modifications.

-Workbench presentation-Creating user parameters and formulas-Defining Checks, Rules, Reactions, Lists, Laws, Loops and macros witharguments-Associating URLs to parameters or relations-Running macros from Rules or Reactions-Using the Knowledge Inspector tool-Managing Design Tables and part family catalogs

ExercisesEx. 1: Wheel Rim (90min) / All sectorsEx. 2: Light Bulb (60min) / All sectorsEx. 3: Sheet Metal Part (30min) / All sectors



KWE: Knowledge Expert

EDU-CAT-E-KWE-FCourse Code EDU-CAT-E-KWE-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWE-FI-V5R18 Foils: EDU-CAT-E-KWE-FF-V5R18 Exercises: EDU-CAT-E-KWE-FX-V5R18

ObjectivesUpon completion of this course you will be able to: - Become familiar with the Knowledgeware working environment, how it can beaccessed, the terminology that will be used and the Settings. - Embed complex design knowledge in a parametric part using Knowledgewareexpert rules checks and reactions. - Automate your designs modifications using various Knowledgeware Experttools.

Participants' ProfileCATIA V5 advanced users

PrerequisitesCATIA V5 Basics CATIA V5 Knowledgeware fundamentals

Content- Introduction to Knowledge Expert- Creating and Using an Expert Rule- Creating and Analyzing an Expert Check- Using a Rule Base

ExercisesEx. 1: Connector (40min) / All sectorsEx. 2: LBlock Correction (40min) / All sectors



KWF: Knowledge Fundamentals

EDU-CAT-E-KWF-FCourse Code EDU-CAT-E-KWF-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWF-FI-V5R18 Foils: EDU-CAT-E-KWF-FF-V5R18 Exercises: EDU-CAT-E-KWF-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:-Access the knowledgeware working environment-Manage the knowledgeware working environment-See how collaborative work affects knowledge features-Use parameters, formulae and design tables-Create parametric parts and assemblies-Share parameters and re-use relations


PrerequisitesStudents attending this course should have knowledge of CATIAV5 PartDesign and CATIA V5 Assembly Design

Content- Introduction to Common Knowledge Tools- Common Knowledge Tools- Collaborative Work and Knowledge- Stringer Assembly Exercice

ExercisesNone



PEO: Product Engineering Optimizer

EDU-CAT-E-PEO-FCourse Code EDU-CAT-E-PEO-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PEO-FI-V5R18 Foils: EDU-CAT-E-PEO-FF-V5R18 Exercises: EDU-CAT-E-PEO-FX-V5R18 Detailed Steps: EDU-CAT-E-PEO-FS-V5R18

ObjectivesIn this course, you will learn the functionalities of CATIA Product EngineeringOptimizer (PEO): - Definition of an optimization problem- Specification of the optimization algorithm,- Solving of an optimization problem,- Analyzing and reporting on the results, - Use of the Design of Experiments tool to understand the behavior of a systemthanks to space exploration,- Use of the Constraint Satisfaction tool to solve complex contraint problems(with no objective function)


PrerequisitesCATIA Basics

Content- Workbench Presentation- Optimization Problem Formulation- Optimization problem resolution- Solution analysis- Best practices for optimization with PEO- Design of Experiments tool- Constraint Satisfaction tool

ExercisesEx. 1: Strap tension optimization (90min) / All sectorsEx. 2: Beam mass optimization (30min) / All sectorsEx. 3: Shape optimization: Hanger (40min) / All sectorsEx. 4: Fastener Shape Optimization (30min) / All sectorsEx. 5: Surfacic structure Structural Optimization (20min) / All sectorsEx. 6: Child Swing Structural Optimization (25min) / All sectorsEx. 7: Silo Structural Optimization (30min) / All sectorsEx. 8: Design of experiments (30min) / All sectorsEx. 9: Beam Mass Minimization through Constraint Satisfaction (20min) / Allsectors



Shape Design & Styling Solutions


Shape Design & StylingSolutions

DL1: Developed Shapes

EDU-CAT-E-DL1-FCourse Code EDU-CAT-E-DL1-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DL1-FI-V5R18 Foils: EDU-CAT-E-DL1-FF-V5R18 Exercises: EDU-CAT-E-DL1-FX-V5R18 Detailed Steps: EDU-CAT-E-DL1-FS-V5R18

ObjectivesUpon completion of this course you will be able to: - Generate unfolded ruled surface - Develop wires and points onto a revolution surface

Participants' ProfileSurface Designers

PrerequisitesStudents attending this course should have knowledge of CATIA V5Fundamentals and Generative Shape Design

ContentUser interface and functionalitiesUser interfaceUnfolded surfacesDevelop wiresExercise PresentationTo Sum Up

ExercisesEx. 1: Water bottle and its support (45min) / All sectors



DSE: Digitized Shape Editor

EDU-CAT-E-DSE-FCourse Code EDU-CAT-E-DSE-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DSE-FI-V5R18 Foils: EDU-CAT-E-DSE-FF-V5R18 Exercises: EDU-CAT-E-DSE-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:- Import and optimize digitized data such as cloud of points- Compute and optimize a mesh based on digitized data- Extract the characteristic curves of a mesh

Participants' ProfileShape Designers

PrerequisitesStudents attending this course should be familiar with the CATIA V5 interface

ContentThis course will teach you how to import, clean and optimize digitized datasuch as clouds of points. You will also learn how to create an optimized meshon the digitized data and how to extract the characteristic curves from thismesh.

- Introduction to Digitized Shape Editor- Point processing- Mesh processing- Scans and curves- Advanced tasks

ExercisesNone



DSS: Shape Sculptor

EDU-CAT-E-DSS-FCourse Code EDU-CAT-E-DSS-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-DSS-FI-V5R18 Foils: EDU-CAT-E-DSS-FF-V5R18 Exercises: EDU-CAT-E-DSS-FX-V5R18

ObjectivesIn this course you will learn how to use the Shape Sculptor product to import,analyze, enhance meshes, then modify them by adding details or deformingshapes.

Participants' ProfileStyle designers, modelers

PrerequisitesCATIA Fundamentals


Content- Introduction to CATIA Shape Sculptor Process overview Polygon modeling Accessing the workbench The user interface Using the compass- General Tools Import Export Display Options Highlight Curvature- Selection and Activation Selection / Activation Selection Activation- Creation Creating Curves 3D Curve Paint Curve Creating meshes Generate mesh Tesselate Rough Offset- Mesh Edition Editing meshes Decimate / Refine Smooth / Brush Smooth Delete / Extract / Copy triangles Slice / Stitch Mesh Intersect Trim/Split- Modeling Shapes Modeling shapes Control points Project curve / Extract curve Curve Sculpt Emboss Push/Pull Surface Sculpt Sharp Edge Grid Modeling Interactive grid Modeling


ExercisesEx. 1: Hairdryer: Import and Analysis / All sectorsEx. 2: Boot ski: Selection and Mesh / All sectorsEx. 3: Bike: Modeling Shapes / All sectorsEx. 4: Dashboard / All sectors



FSK: FreeStyle Sketch Tracer

EDU-CAT-E-FSK-FCourse Code EDU-CAT-E-FSK-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSK-FI-V5R18 Foils: EDU-CAT-E-FSK-FF-V5R18 Exercises: EDU-CAT-E-FSK-FX-V5R18

ObjectivesUpon completion of this course you will be able to: Use an image as a background or as a basis for design Import an image into CATIA V5 Position an image in the CATIA V5 environment

Participants' ProfileShape Designers

PrerequisitesStudents attending this course should have experience in the followingdomain(s): CATIA V5 fundamentals

ContentIntroduction to CATIA Sketch TracerIntroductionAccessing theworkbenchUser Interface: Sketch TracerImporting the Sketches What is Importing a Sketch Why Import a SketchHow to Create an Immersive Sketch How to Create an Immersive Sketch Using Screen ShotModifying theAppearance of a Sketch Manipulating the FocusPositioning the SketchesWhat is Positioning a Sketch ?How to Positiona Sketch Using Cylindrical ViewHow to Position a Sketch Using ConicalViewmanaging Views What is Managing Views ? How to Manage Interactive ViewsHow to Manage Conical Views

What is new in this releaseSea Car exercise modified

ExercisesNone



FSS: FreeStyle Shaper, Optimizer & Profiler

EDU-CAT-E-FSS-FCourse Code EDU-CAT-E-FSS-FCATIA V5R18Brand & Release CATIA V5R181.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSS-FI-V5R18 Foils: EDU-CAT-E-FSS-FF-V5R18 Exercises: EDU-CAT-E-FSS-FX-V5R18

ObjectivesIn this course you will learn how to:- Create styled shapes using digitized data- Create surfaces using a curve-based approach- Create surfaces using a surface-based approach - Analyze and correct the curve quality- Analyze and correct the surface quality�


PrerequisitesStudents attending this course should have knowledge of CATIA SurfaceDesign (EDU-CAT-E-GS1-F - V5R16)

ContentThis course teaches you how to create flawless, styled shapes from scratchusing three-dimensional free-form curves and surfaces or with digitized data.You will also learn how to analyze and improve the quality of existing curvesand surfaces.

Introduction to Freestyle Shaper

Using the Curve-Based Approach

Using the Surface-Based Approach

Analysis Tools

What is new in this release- Creating a Styling fillet added

ExercisesNone



GSD: Surface Design Expert

EDU-CAT-E-GSD-FCourse Code EDU-CAT-E-GSD-FCATIA V5R18Brand & Release CATIA V5R182 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSD-FI-V5R18 Foils: EDU-CAT-E-GSD-FF-V5R18 Exercises: EDU-CAT-E-GSD-FX-V5R18

ObjectivesUpon completion of this course, you will be able to:- Correctly recall the tools of the Generative Shape Design workbench that arecommon to MD2 and HD2 licenses- Identify and use the Generative Shape Design tools that are specific to theHD2 license- Create advanced and parameterized swept surfaces- Perform advanced surfaces analysis and gap correction- Improve geometry quality and stability

Participants' ProfileMechanical Surface Designers

PrerequisitesStudents who are familiar with the basics of wireframe and surfaces creation

ContentThis course focuses on the Generative Shape Design tools specific to the HD2license and will first recall and summarize the tools covered in the SurfaceDesign course. You will capitalize on this with advanced surfaces creationtools, quality checking and correction techniques, and be introduced to surfacecreation in a multi-model environment.

- Inroduction to Surface Design- Creating Advanced Wireframe Features- Wireframe Analysis and Repair- Creating Advanced Swept Surfaces- Creating Advanced Blending Surfaces- Surface Analysis- Additional Surface Design Tools

What is new in this releaseThis course was updated in order to reflect the main CATIA V5R17enhancements

ExercisesNone



GSO: Generative Shape Optimizer

EDU-CAT-E-GSO-FCourse Code EDU-CAT-E-GSO-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSO-FI-V5R18 Foils: EDU-CAT-E-GSO-FF-V5R18 Exercises: EDU-CAT-E-GSO-FX-V5R18 Detailed Steps: EDU-CAT-E-GSO-FS-V5R18

ObjectivesUpon completion of the course you will learn to:- Develop Shapes- Morph Shapes- Create Junctions (BIW application) between surfaces- Work with Volumes- Create junctions between existing beams- Morph surfaces using target curves and shapes- Add bumps on surfaces


PrerequisitesStudents attending this course should have knowledge of:CATIA Surface Design.

ContentThis course introduces you to the Generative Shape Optimizer tools within theGSD workbench. You will learn how to manage volumes and how to defomrshapes using the morphing and bump tools. You will also learn how to developshapes and how to create junctions between beams.

Introduction to Generative Shape Optimizer - Accessing Generative Shape Optimizer - The User InterfaceCreating Offsets: - Variable Offset - Rough OffsetDeveloping Shapes: - Developing wireUsing BiW Tools: - Creating junctions - Creating a Diabolo SeatCreating Advanced Surfaces: - Creating bumped surfaces - Deforming surfaces according to curve wrapping - Deforming surfaces according to surface wrapping - Shape MorphingCreating Volumes - What is a Volume - Types of Volumes - Volumes made from Sketches - Volumes made from Surfaces - Dress-up features on Volumes - Volumes using Boolean operations - Volumes from Operations or Transformations


ExercisesNone



HD2: Generative Shape Design V5R18 Update

EDU-CAT-E-HD2-UCourse Code EDU-CAT-E-HD2-UCATIA V5R18Brand & Release CATIA V5R180.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-HD2-UI-V5R18 Foils: EDU-CAT-E-HD2-UF-V5R18

ObjectivesUpon completion of this course you will be able to use the new and enhancedfunctionalities of V5R18 Generative Shape Design workbench.

Participants' ProfileCATIA Surface Designers

PrerequisitesStudents attending this course must have knowledge of CATIA GenerativeShape Design V5R17.

Content-Enhancements in Sweep-Chordal Fillet-Other Enhancements

ExercisesNone



IMA: Imagine & Shape

EDU-CAT-E-IMA-FCourse Code EDU-CAT-E-IMA-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-IMA-FI-V5R18 Foils: EDU-CAT-E-IMA-FF-V5R18 Exercises: EDU-CAT-E-IMA-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:- Explain what is a subdivision surface- Create and deform subdivision surfaces- Create and deform IMA curves with the curve modeler- Associate curves with subdivision surfaces

Participants' ProfileThis course is targeted mainly for CATIA:Application engineersMechanical DesignersIndustrial Designers

PrerequisitesStudents attending this course should be familiar with the Generative ShapeDesign workbench

ContentThis course will introduce the concept of subdivision surfaces and will teachyou the tools available to create these surfaces. You will learn themanipulations necessary to modify and shape the subdivision surfaces. Youwill also learn how to create curves with the curve modeler and how toassociate subdivision surfaces with curves.

Introduction to Imagine & Shape

Surface modeling:-Creating Basic Surfaces-Manipulating Surfaces-Modifying the Topology

Curve modeling:-Curve creation-CUrve deformation

Curve creation:-Curve deformation-Sketching-Manipulate point-Smoothing-Fillet-Erase-On plane

Imaging and Shape Recommendation

ExercisesNone



QSR: Quick Surface Reconstruction

EDU-CAT-E-QSR-FCourse Code EDU-CAT-E-QSR-FCATIA V5R18Brand & Release CATIA V5R181 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-QSR-FI-V5R18 Foils: EDU-CAT-E-QSR-FF-V5R18 Exercises: EDU-CAT-E-QSR-FX-V5R18

ObjectivesUpon Completion of this course you will be able to:- Create Scans from point cloud data- Create curves from scans- Create surfaces from scans- Create model and fillet model


PrerequisitesStudents attending this course should have experience in the followingdomain(s):CATIA V5 fundamentals, Digitized Shape Editor and Surface Design

ContentThis course will show you how to reuse tools from Digitized Shape Editorworkbench, and which are the tools specific to QSR. You will learn how scansand curves can be rapidly created on a mesh, and how surfaces can be quicklyderived from the resulting curves.

- Introduction- Creating scans- Creating curves- Creating surfaces- Create curve networks- Automatic processes

ExercisesNone



RSO: Realistic Shape Optimizer

EDU-CAT-E-RSO-FCourse Code EDU-CAT-E-RSO-FCATIA V5R18Brand & Release CATIA V5R180.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-RSO-FI-V5R18 Foils: EDU-CAT-E-RSO-FF-V5R18 Exercises: EDU-CAT-E-RSO-FX-V5R18

ObjectivesIn this course you will learn how to deform a surface or a set of surfaces usinga displacement file resulting from a finite element analysis

Participants' ProfileSurface design Specialist or Expert Surface designers involved in tooling design

PrerequisitesGS1: CATIA Surface Design Companionor

CCV: Core & Cavity Design

ContentIntroduction to Realistic Shape Optimizer - Why do you need RSO ?Workbench presentation- Accessing the workbenchSurface Deformation - Digitized Morphing- Update Digitized Morphing

ExercisesEx. 1: Master exercise: Plastic Cover (30min) / All sectorsEx. 2: Additionnal exercise: Plane wing (30min) / Aerospace



V5S: V5 Surface Design

EDU-CAT-E-V5S-FCourse Code EDU-CAT-E-V5S-FCATIA V5R18Brand & Release CATIA V5R183 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanionMethod Companion

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5S-FI-V5R17 Foils: EDU-CAT-E-V5S-FF-V5R17

ObjectivesUpon Completion of this course you will be able to: - Understand the GSD workbench - Create good quality curves or improve imported wireframe - Create good quality surfaces based on a sound wireframe geometry - Assemble, relimit and smoothly connect the surfaces to get a topology - Analyze surface quality and heal the defects - Manage surfaces in a multimodel environment

Participants' Profile-Users familiar with CATIA V5 Fundamentals -Users who need to learn how to create advanced Mechanical Surfaces

PrerequisitesStudents attending this course should be familiar with CATIA V5 Fundamentalsand Microsoft Windows Operating System

Content- Lesson 1: Introduction to Generative Shape Design- Lesson 2: Wireframe Creation- Lesson 3: Surface Creation- Lesson 4: Surface Re-limitation and Connection- Lesson 5: Surface Check Tools- Lesson 6: Work in Multi-Model Environment with Surface- Master Project- Additional Exercises

NotesIn addition to the exercises specified just above, this course contains:- Exercises included in the flow of the lessons to make students to manipulateon simple data and get familiar with the tools- Case Study exercises at the end of each lesson to allow students to reviewthe tools seen in the lesson in a more concret set of data

This course also contains CATIA demonstration data including instructions inthe CATParts (3D annotations) to help the teacher to show what has to beshown.These demonstration data are also provided to the students (for lessons 2 to 5)to make the students manipulate while the teacher demonstrates.

ExercisesEx. 1: Master Project: Toy Car (200min) / All sectorsEx. 2: Additional Exercise: Mobile Phone (60min) / All sectorsEx. 3: Additional Exercise: Plastic Bottle (180min) / All sectors


Date post:	24-Mar-2015
Category:	Documents
Upload:	nanda-sundaram
View:	308 times
Download:	15 times

43678371 CATIA V5R18 Course Catalog

Documents