Date post: | 29-Nov-2014 |
Category: |
Documents |
Upload: | juzze-limer |
View: | 135 times |
Download: | 8 times |
ROI-S05590-054E 060323
P ASOLINK
N ETWORK
M ANAGEMENT
T ERMINAL
PNMT (Java version)Installation Manual
(WindowsXP)
NEC CorporationCopyright © 2006
ROI-S05590
- i -
Table of Contents
1. Installation Sequence ............................................................................................................................ 1
2. Phone and Modem Options Setting (Standard 19.2Kbps Connection) ............................................ 2
3. Installation of USB Com Port Driver (USB Connection)................................................................... 7
4. Dial-up Setting ..................................................................................................................................... 10
4 SNMP Service Setting ......................................................................................................................... 20
5 PNMT Setup ........................................................................................................................................ 25
6 Launching PNMT................................................................................................................................ 29
ROI-S05590
- 1 -
1. Installation Sequence
Step1: Modem Setting
Standard 19200bps Modem Setting (Phone and Modem Options Setting)
USB Modem Setting (Installation of USB Com Port Driver)
Step2: Dial-up Connection Setting
Step3: SNMP Service Setting
Step4: Pasolink Network Management Terminal (PNMT) Setup
Step5: Launching PNMT
Network Element (NE) other thanPASOLINK NEO
PASOLINK NEO ONLY
ROI-S05590
- 2 -
2. Phone and Modem Options Setting (Standard 19.2Kbps Connection)
This section deals with the use of a Standard 19.2Kbps Modem Dial-up connection. (for non-PASOLINK-NEO network elements). If you wish to use a USB Modem Driver (for PASOLINK-NEO network elements, please refer to 3.”Installation of USB Com Port Driver”, p.7
(1) Click Start | Settings | Control Panel.
(2) Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.
ROI-S05590
- 3 -
(3) Enter your country and area code in the Location Information window. Click [OK].
(4) Verify the Location and Area Code.
ROI-S05590
- 4 -
(5) Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.
(6) Check Don’t detect my modem ... and click [Next] to continue.
ROI-S05590
- 5 -
(7) Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models . Click [Next] to continue.
(8) Select Selected ports and COM#, then click [Next] to continue.
ROI-S05590
- 6 -
(9) Click [Finish] to complete the new modem installation.
(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].
(11) Please proceed directly to section 4. Dial-up Setting.
ROI-S05590
- 7 -
3. Installation of USB Com Port Driver (USB Connection)
This section deals with installation of a USB Modem Driver (for PASOLINK-NEO network elements) as the dial-up connection. Connect the PNMT computer to the LCT Port of the NE with a standard USB cable.
(1) Select No, not this time and Click [Next].
(2) Select Install from a list or specific location [Advanced] and click on [Next].
ROI-S05590
- 8 -
(3) Insert the USB driver CD-ROM in the computer’s disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].
(4) Click [Continue Anyway] in the Hardware Installation pop-up alert.
ROI-S05590
- 9 -
(5) USB Modem Driver Installation starts.
(6) USB Com Port Driver installation is complete.
ROI-S05590
- 10 -
4. Dial-up Setting
(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.
(2) The Network Connections window appears. Click Create a new connection in the Network Tasks area.
ROI-S05590
- 11 -
(3) The Welcome to the New Connection Wizard window appears. Click [Next].
(4) Select Connect to the network at my workplace and click [Next] to continue.
ROI-S05590
- 12 -
(5) Select Dial-up connection and click [Next] to continue.
(6) Select Modem – USB Modem Driver [COM#] and click [Next] to continue.
NOTE
This screen appears only when a USB Modem Driver has been installed.
ROI-S05590
- 13 -
(7) In the New Connection Wizard window, enter Pnmt in the Company Name field and click [Next] to continue.
(8) Enter any number in the Phone number field and click [Next] to continue.
ROI-S05590
- 14 -
(9) Verify that Pnmt is displayed as the connection. You can also create a shortcut on your desktop if desired. Click [Finish].
(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.
ROI-S05590
- 15 -
(11) Verify that Modem-Standard 19200 bps Modem [COM1] is displayed on the General tab in the Dial-up Connection Properties window. Click [Configure].
(12) In the Modem Configuration window, uncheck all five boxes.
ROI-S05590
- 16 -
(13) Retain the default setting on the Options tab and click the Security tab.
(14) Retain the default setting on the Security tab and click the Networking tab.
ROI-S05590
- 17 -
(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....
(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to
go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].
ROI-S05590
- 18 -
(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.
(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link.
Click [OK].
ROI-S05590
- 19 -
(19) Retain the default setting on the Advanced tab and click [OK].
After activating Windows XP SP2 Before activating Windows XP SP2
ROI-S05590
- 20 -
4 SNMP Service Setting
NOTE
It is necessary to remove SNMP Service or to stop it if it has already been installed.
To Remove SNMP Service:
(1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click
Add/Remove Windows Components.
(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ....
ROI-S05590
- 21 -
(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].
(4) Click [Finish] to complete the removal of SNMP Service.
ROI-S05590
- 22 -
To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel
window.
(6) Click Services in the Administrative Tools window.
ROI-S05590
- 23 -
(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu..
(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].
ROI-S05590
- 24 -
(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is Stopped, and that the startup condition for each one is Manual.
(10) Restart the computer.
ROI-S05590
- 25 -
5 PNMT Setup
NOTE
If PNMT software has already been installed, please uninstall it before you install a new version.
(1) Insert the PNMT Installation CDROM. Open the CDROM folder and double-click
setupwin32.exe.
(2) The following window appears until loading is completed.
ROI-S05590
- 26 -
(3) The welcome message window appears. Click [Next].
(4) Specify the directory in which the PNMT is to be installed. Click [Next].
NOTE
The default pass file is C:\PNMTj. It is not possible to include blank spaces as in “Program Files”.
ROI-S05590
- 27 -
(5) Specify the License.Key file if one is available. Click [Next].
NOTE
If no License Key is available, operation in Trial mode is possible. Simply leave the License Key field blank and proceed.
(6) Click [Install].
ROI-S05590
- 28 -
(7) During installation, this window appears.
(8) Click [Finish] to close the PNMT installation wizard.
ROI-S05590
- 29 -
6 Launching PNMT
(1) Click Start | Programs |PNMTj |PNMT to start the application.
(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).
ROI-S05590
- 30 -
(3) Enter User name and Password, and Select the Connection Entry.
After installation of the PNMT, the initial password will be:-
User name: admin
Password: (There is no initial password. Just press Enter.
A password can then be set.)
Connection: Select Dial-up and Pnmt entry.
NOTE
If another application is using the SNMP Port, application initialization will not be possible, the application will shut down, and the following message will appear.