BARTEK
www.bartek.com.au
BARTEKMaking the Connection
Product Catalogue December 2019
info@bartek,com.au | www.bartek.com.au
REBAR COUPLERS
BARTEK
www.bartek.com.au
TB Inserts for Reidbar
TB Couplers for Reidbar
TB Nail Plates for ReidbarPRODUCT
CODEPRODUCT DESCRIPTION
TB12NPR TB Nail Plate 12mm for Reidbar – Bag of 100
TB16NPR TB Nail Plate 16mm for Reidbar – Bag of 100
TB20NPR TB Nail Plate 20mm for Reidbar – Bag of 100
TB25NPR TB Nail Plate 25mm for Reidbar – Bag of 50
TB32NPR TB Nail Plate 32mm for Reidbar – Bag of 40
Rebate Boards - Polyurethane - Re-useable
PRODUCT CODE
PRODUCT DESCRIPTION
RBP10009030 Bartek Polyurethane Rebate Board - 1000x90x30
RBP12009030 Bartek Polyurethane Rebate Board - 1200x90x30
RBP100015030 Bartek Polyurethane Rebate Board - 1000x150x30
RBP120015030 Bartek Polyurethane Rebate Board - 1200x150x30
Reidbar Starter Bars
PRODUCT CODE
PRODUCT DESCRIPTION
TB12IR TB Insert 12mm to suit Reidbar
TB16IR TB Insert 16mm to suit Reidbar
TB20IR TB Insert 20mm to suit Reidbar
TB25IR TB Insert 25mm to suit Reidbar
TB32IR TB Insert 32mm to suit Reidbar
PRODUCT CODE
PRODUCT DESCRIPTION
TB12CR TB Coupler 12mm to suit Reidbar
TB16CR TB Coupler 16mm to suit Reidbar
TB20CR TB Coupler 20mm to suit Reidbar
TB25CR TB Coupler 25mm to suit Reidbar
TB32CR TB Coupler 32mm to suit Reidbar
PRODUCT CODE
PRODUCT DESCRIPTION
RB12.600 ThreadBar Starter Bar 12mm x 600mm
TB16.750 ThreadBar Starter Bar 16mm x 750mm
TB20.1000 ThreadBar Starter Bar 20mm x 1000mm
TB25.1200 ThreadBar Starter Bar 25mm x 1200mm
TB32.1500 ThreadBar Starter Bar 32mm x 1500mm
BARTEK
www.bartek.com.au
JEMEG PT Couplers
PRODUCT CODE
PRODUCT DESCRIPTION
PT12C Parallel Thread Coupler 12mm
PT16C Parallel Thread Coupler 16mm
PT20C Parallel Thread Coupler 20mm
PT24C Parallel Thread Coupler 24mm
PT28C Parallel Thread Coupler 28mm
PT32C Parallel Thread Coupler 32mm
PT36C Parallel Thread Coupler 36mm
PT40C Parallel Thread Coupler 40mm
JEMEG PT Couplers – Hot Dip Galvanised
PRODUCT CODE
PRODUCT DESCRIPTION
PT12CG Parallel Thread Coupler 12mm Galvanized
PT16CG Parallel Thread Coupler 16mm Galvanized
PT20CG Parallel Thread Coupler 20mm Galvanized
PT24CG Parallel Thread Coupler 24mm Galvanized
PT28CG Parallel Thread Coupler 28mm Galvanized
PT32CG Parallel Thread Coupler 32mm Galvanized
PT36CG Parallel Thread Coupler 36mm Galvanized
PT40CG Parallel Thread Coupler 40mm Galvanized
PT Inserts
PRODUCT CODE
PRODUCT DESCRIPTION
PT12I Parallel Thread Insert 12mm
PT16I Parallel Thread Insert 16mm
PT20I Parallel Thread Insert 20mm
PT24I Parallel Thread Insert 24mm
BARTEK
www.bartek.com.au
JEMEG PT Couplers – Lock Nuts
PRODUCT CODE
PRODUCT DESCRIPTION
PT12LN Parallel Thread Lock Nut 12mm
PT16LN Parallel Thread Lock Nut 16mm
PT20LN Parallel Thread Lock Nut 20mm
PT24LN Parallel Thread Lock Nut 24mm
PT28LN Parallel Thread Lock Nut 28mm
PT32LN Parallel Thread Lock Nut 32mm
PT36LN Parallel Thread Lock Nut 36mm
PT40LN Parallel Thread Lock Nut 40mm
JEMEG PT Adjustable Couplers
PRODUCT CODE
PRODUCT DESCRIPTION
PT16AC Parallel Thread Adjustable Coupler 16mm
PT20AC Parallel Thread Adjustable Coupler 20mm
PT24AC Parallel Thread Adjustable Coupler 24mm
PT28AC Parallel Thread Adjustable Coupler 28mm
PT32AC Parallel Thread Adjustable Coupler 32mm
PT36AC Parallel Thread Adjustable Coupler 36mm
PT40AC Parallel Thread Adjustable Coupler 40mm
JEMEG PT Couplers – Stainless Steel
PRODUCT CODE
PRODUCT DESCRIPTION
PT12CS Parallel Thread Coupler 12mm Stainless
PT16CS Parallel Thread Coupler 16mm Stainless
PT20CS Parallel Thread Coupler 20mm Stainless
PT24CS Parallel Thread Coupler 24mm Stainless
PT28CS Parallel Thread Coupler 28mm Stainless
PT32CS Parallel Thread Coupler 32mm Stainless
PT36CS Parallel Thread Coupler 36mm Stainless
PT40CS Parallel Thread Coupler 40mm Stainless
BARTEK
www.bartek.com.au
PT Couplers – Terminators
PRODUCT CODE
PRODUCT DESCRIPTION
PT20T Parallel Thread Terminator 20mm
PT24T Parallel Thread Terminator 24mm
PT28T Parallel Thread Terminator 28mm
PT32T Parallel Thread Terminator 32mm
PT36T Parallel Thread Terminator 36mm
PT40T Parallel Thread Terminator 40mm
PT Threading
PRODUCT CODE
PRODUCT DESCRIPTION
PT12TH Parallel Threading 12mm
PT16TH Parallel Threading 16mm
PT20TH Parallel Threading 20mm
PT24TH Parallel Threading 24mm
PT28TH Parallel Threading 28mm
PT32TH Parallel Threading 32mm
PT36TH Parallel Threading 36mm
PT40TH Parallel Threading 40mm
Threaded Starter Bars
PRODUCT CODE
PRODUCT DESCRIPTION
N12.600PT N12 Starter Bar 600mm long with PT Thread
N16.800PT N16 Starter Bar 800mm long with PT Thread
N20.900PT N20 Starter Bar 900mm long with PT Thread
N24.1100PT N24 Starter Bar 1100mm long with PT Thread
N28.1260PT N28 Starter Bar 1260mm long with PT Thread
N32.1470PT N32 Starter Bar 1470mm long with PT Thread
N16.600M16 N16 Starter Bar 600mm long with M16 Thread
N20.600M20 N20 Starter Bar 600mm long with M20 Thread
N20.900M20 N20 Starter Bar 900mm long with M20 Thread
BARTEK
www.bartek.com.au
PT Nail PlatesPRODUCT
CODEPRODUCT DESCRIPTION
PT12NP PT Nail Plate 12mm – Bag of 100
PT16NP PT Nail Plate 16mm – Bag of 100
PT20NP PT Nail Plate 20mm – Bag of 100
PT24NP PT Nail Plate 24mm – Bag of 100
PT28NP PT Nail Plate 28mm – Bag of 100
PT32NP PT Nail Plate 32mm – Bag of 100
PT36NP PT Nail Plate 36mm – Bag of 100
PT40NP PT Nail Plate 40mm – Bag of 100
BP Standard CouplersPRODUCT
CODEPRODUCT DESCRIPTION
BPS12F BP Coupler 12mm Female
BPS12M BP Coupler 12mm Male
BPS16F BP Coupler 16mm Female
BPS16M BP Coupler 16mm Male
BPS20F BP Coupler 20mm Female
BPS20M BP Coupler 20mm Male
BPS24F BP Coupler 24mm Female
BPS24M BP Coupler 24mm Male
BPS28F BP Coupler 28mm Female
BPS28M BP Coupler 28mm Male
BPS32F BP Coupler 32mm Female
BPS32M BP Coupler 32mm Male
BP Standard Couplers – Hot Dip GalvanisedPRODUCT
CODEPRODUCT DESCRIPTION
BPS12FG BP Coupler 12mm Female – HDG
BPS16FG BP Coupler 16mm Female – HDG
BPS20FG BP Coupler 20mm Female – HDG
BPS24FG BP Coupler 24mm Female – HDG
BPS28FG BP Coupler 28mm Female - HDG
BPS32FG BP Coupler 32mm Female - HDG
Metric Thread Nail PlatesPRODUCT
CODEPRODUCT DESCRIPTION
M16NP M16 Nail Plate for BP12 – Bag of 100
M20NP M20 Nail Plate for BP16 – Bag of 100
M24NP M24 Nail Plate for BP20 – Bag of 100
M30NP M30 Nail Plate for BP24 – Bag of 100
M33NP M33 Nail Plate for BP28 – Bag of 100
M36NP M36 Nail Plate for BP32 – Bag of 50
ADDRESS: 7 Brisbane Road, (PO Box 6062), Riverview QLD 4303 Australia PHONE +61 7 3816 5500 FAX +61 7 3282 0118
ALS INDUSTRIAL PTY LTD ABN 21 006 353 046 Part of the ALS Laboratory Group ALS Limited Company
MECHANICAL TESTING REPORT
Report No: QRM16-0206
Date of Issue: 06-04-2016
Page: 1 of 2
Client: Bartek Pty. Ltd.
Attention: David Short
Address: PO Box 578
Kallangur, QLD 4503
Order Number: COD
Job Description: Mechanical testing of (1) only Rebar coupler sample.
Accredited for compliance
with ISO/IEC 17025.
This document will not be
reproduced except in full.
Accreditation # 218
Josh Ford
Laboratory Technician
Mechanical Testing
Note:
1. All work is subject to our standard terms and conditions, available on our website
http://www.alsglobal.com/en/Our-Services/Industrial/Asset-Care/Downloads
2. Test plates and specimens will be disposed of 30 days from issue date of this report
unless other arrangements have been made.
3. This report is based on information supplied by the client and cannot be substantiated.
Report No.: QRM16-0206
PAGE NO: 2 OF 2
Test Piece Identification: Rebar to Coupler Sample – TB16CR
Nominated Material
Specification: Rebar – AS/NZS 4671 – 2001 Grade 500N (16mm Ø)
Coupler – Carbon Steel – Not Further Specified
Test Specification: AS 3600 – 2009 Clause 13.2.6
In general accordance with AS/NZS 1391 – 2007
Date of Examination: 06-04-2016
TENSILE TEST
Nominal Diameter mm 16
Area mm2
201
Visible Defects Nil
Location of Fracture Rebar – 40mm away from coupler
Fracture Face Appearance Ductile
Tensile Load kN 130.71
Tensile Stress MPa 650
RESULT COMPLIES
Sample Post Test
ALS Industrial Pty Ltd
7 Brisbane Road
Riverview QLD 4303
T +61 7 3816 5500 F +61 7 3282 0118
ABN: 21 006 353 046
Right Solutions • Right Partner www.alsglobal.com
MECHANICAL TESTING REPORT
Report No: 71930-ME-05
Date of Issue:
Interim Results:
08-02-2019
Emailed 08-02-2019
Page: 1 of 2
Client: Bartek Pty. Ltd.
Attention: David Short
Address: PO Box 578
Kallangur, Qld 4503
Order Number: COD
Job Description: Mechanical testing of (1) only reidbar coupler sample.
Accredited for compliance with ISO/IEC
17025 – Testing. This document will not
be reproduced except in full.
Accreditation # 218 Site# 852
Luke Davies
Laboratory Technician
Mechanical Testing
Note:
1. All work is subject to our standard terms and conditions, available on our website
http://www.alsglobal.com/en/Our-Services/Industrial/Asset-Care/Downloads
2. Test plates and specimens will be disposed of 30 days from issue date of this report
unless other arrangements have been made.
3. This report is based on information supplied by the client and cannot be substantiated.
Report No: 71930-ME-05 P2 of 2
Right Solutions • Right Partner www.alsglobal.com
Test Piece
Identification:
TB20CR - Reidbar to Coupler Sample – Ø20
Nominated Material
Specification:
Reidbar – Carbon Steel – Not Further Specified
Coupler – Carbon Steel – Not Further Specified
Test Specification: AS 3600 – 2009 Clause 13.2.6
Requirement: Failure Greater than 540MPa
In general accordance with AS/NZS 1391 – 2007
Date of Examination: 08-02-2019
TENSILE TEST
Nominal Diameter mm 20
Area mm2
314.16
Visible Defects Nil
Location of Fracture Bar fractured 60mm away from the coupler
Fracture Face Appearance Ductile
Tensile Load kN 221.110
Tensile Stress MPa 704
RESULT COMPLIES
Sample Post Test
ALS Industrial Pty Ltd
7 Brisbane Road
Riverview QLD 4303
T +61 7 3816 5500 F +61 7 3282 0118
ABN: 21 006 353 046
Right Solutions • Right Partner www.alsglobal.com
MECHANICAL TESTING REPORT
Report No: 48680-ME-01
Date of Issue:
Interim Results:
12-08-2017
Emailed 12-08-2017
Page: 1 of 2
Client: Bartek Pty. Ltd.
Attention: David Short
Address: PO Box 578
Kallangur, QLD 4503
Order Number: COD
Job Description: Mechanical testing of (1) only reidbar coupler sample.
Accredited for compliance with ISO/IEC
17025 – Testing. This document will not
be reproduced except in full.
Accreditation # 218 Site# 852
Luke Davies
Laboratory Technician
Mechanical Testing
Note:
1. All work is subject to our standard terms and conditions, available on our website
http://www.alsglobal.com/en/Our-Services/Industrial/Asset-Care/Downloads
2. Test plates and specimens will be disposed of 30 days from issue date of this report
unless other arrangements have been made.
3. This report is based on information supplied by the client and cannot be substantiated.
Report No: 48680-ME-01 P2 of 2
Right Solutions • Right Partner www.alsglobal.com
Test Piece
Identification:
TB25CR - Reidbar to Coupler Sample – Ø25
Nominated Material
Specification:
Reidbar – Carbon Steel – Not Further Specified
Coupler – Carbon Steel – Not Further Specified
Test Specification: AS 3600 – 2009 Clause 13.2.6
Requirement: Failure Greater than 540MPa
In general accordance with AS/NZS 1391 – 2007
Date of Examination: 11-08-2017
TENSILE TEST
Nominal Diameter mm 25
Area mm2
490.875
Visible Defects Nil
Location of Fracture Bar fractured 70mm away from the coupler
Fracture Face Appearance Ductile
Tensile Load kN 328.596
Tensile Stress MPa 669
RESULT COMPLIES
Sample Post Test
ALS Industrial Pty Ltd
7 Brisbane Road
Riverview QLD 4303
T +61 7 3816 5500 F +61 7 3282 0118
ABN: 21 006 353 046
Right Solutions • Right Partner www.alsglobal.com
MECHANICAL TESTING REPORT
Report No: 48680-ME-03
Date of Issue:
Interim Results:
12-08-2017
Emailed 12-08-2017
Page: 1 of 2
Client: Bartek Pty. Ltd.
Attention: David Short
Address: PO Box 578
Kallangur, QLD 4503
Order Number: COD
Job Description: Mechanical testing of (1) only reidbar coupler sample.
Accredited for compliance with ISO/IEC
17025 – Testing. This document will not
be reproduced except in full.
Accreditation # 218 Site# 852
Luke Davies
Laboratory Technician
Mechanical Testing
Note:
1. All work is subject to our standard terms and conditions, available on our website
http://www.alsglobal.com/en/Our-Services/Industrial/Asset-Care/Downloads
2. Test plates and specimens will be disposed of 30 days from issue date of this report
unless other arrangements have been made.
3. This report is based on information supplied by the client and cannot be substantiated.
Report No: 48680-ME-03 P2 of 2
Right Solutions • Right Partner www.alsglobal.com
Test Piece
Identification:
TB32CR - Reidbar to Coupler Sample – Ø32
Nominated Material
Specification:
Reidbar – Carbon Steel – Not Further Specified
Coupler – Carbon Steel – Not Further Specified
Test Specification: AS 3600 – 2009 Clause 13.2.6
Requirement: Failure Greater than 540MPa
In general accordance with AS/NZS 1391 – 2007
Date of Examination: 11-08-2017
TENSILE TEST
Nominal Diameter mm 32
Area mm2
804.250
Visible Defects Nil
Location of Fracture Bar fractured 80mm away from the coupler
Fracture Face Appearance Ductile
Tensile Load kN 560.976
Tensile Stress MPa 698
RESULT COMPLIES
Sample Post Test