1
DETAIL - A DETAIL - B 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 A A B B C C D D E E F F G G H H I I J J K K L L APPROVED: CHECKED: DRAWN: DATE: DATE: DATE: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN:- MM DIMENSIONS AND TOLERANCING AS PER AS 1100.101 - 1992 SCALE:- ITEM CONTROL:- SHEET:- OF CODE INDENT No:- DRAWING NUMBER:- PART NUMBER:- SHEET SIZE:- IDENTIFIER:- ITEM NAME:- Cummins Engine Company P/L. 2 CARIBBEAN DRIVE, SCORESBY, VICTORIA, 3179 (A.B.N. - 42 006 332 949) THIS DOCUMENT (AND THE INFORMATION SHOWN THEREON) IS CONFIDENTIAL AND PROPRIETARY AND SHALL NOT BE DISCLOSED TO OTHERS IN HARD COPY OR ELECTRONIC FORM, REPRODUCED BY ANY MEANS, OR USED FOR ANY PURPOSE WITHOUT WRITTEN CONSENT OF CUMMINS ENGINE COMPANY, P/L. J.E.ZAMMIT L.EDWARDS D.PIETSCH 3/09/2008 5/09/2008 5/09/2008 6BTA 24V FIRE PUMP ASSEMBLY CSP08544 CSP08544 6BTA 24V FIRE PUMP A0 1 1 1:4 Created with Autodesk Inventor LETTERING SEQUENCE FOR PRELIMINARY REVISIONS. A,B,C, AND NUMERICAL SEQUENCE FOR PRODUCTION RELEASE. 00,01,02 APPROX MASS: THIS HARD COPY DRAWING MAY NOT BE CURRENT RELEASE - PLEASE CHECK R-DRIVE PUBLIC FOR THE LATEST REVISION. 1.638 kg AIR FILTER KIT 6BTA 24V ACSP0026 ACSP0026 1 10 0.506 kg STOP SOLENOID ASSY 6BTA & 6CTA 24V ASSP0012 ASSP0012 1 9 14.850 kg ENGINE SUPPORT - LEG KIT BRSP0045 BRSP0045 1 8 31.769 kg COOLING SYSTEM - HEAT EXCHANGER CSSP0024 CSSP0024 1 7 0.792 kg BLOCK HEATER ASSEMBLY 4BTA & 6BTA EGSP0115 EGSP0115 1 6 137.389 kg ENGINE - 6BTA 5.9 - C180 23123 FRSP0024 1 5 3.922 kg BELT GUARD ASSEMBLY - 24V FIRE PUMPS SGSP0001 SGSP0001 1 4 0.182 kg BRACKET THROTTLE LINKAGE KIT TLSP0015 TLSP0015 1 3 0.076 kg EXHAUST - 4BT,4BTA,6BT & 6BTA XSSP0044 XSSP0044 1 2 6.016 kg GUARD ASSEMBLY - TURBO XSSP0054 XSSP0054 1 1 MASS DESCRIPTION PART No:- DWG No:- QTY ITEM A B ANGLE TOLERANCE: ( DEG~ ) ` 1~ 00.00 ` 0.25 00.0 ` 0.5 00. ` 4 UNLESS OTHERWISE SPECIFIED, TOLERANCES ON ALL DIMENSIONS OF LENGTH & ANGLE SHALL BE: REV DESCRIPTION DRWN CHKD ENG APPVD DRAWING No:- USED ON:- CSP08544 DO NOT SCALE IF IN DOUBT ASK ! REMOVE ALL BURRS AND SHARP EDGES (728) (894) (325) (1220) (411) - FRONT LEG (524) - REAR LEG (205) (744) (646) (461) 3 4 8 7 2 5 RELEASED FOR PRODUCTION 17/07/2015 (1164) (771) (806) NOTE: HOSE PROFILE REFERENCE ONLY. (935) C L C L (830) (394) 10 (182) (167) NOTE: FUEL FILTER REMOVAL DISTANCE 50MM OIL FILTER REMOVAL DISTANCE 100MM FUEL INLET M16 X 1.5 FLYWHEEL - FW90104 MOUNTING HOLES 8 - OFF TAPPED M10 x 20 DEEP FLYWHEEL HOUSING FH9712 - SAE 3 MOUNTING HOLES 12 - OFF TAPPED M10 x 1.5 -6H WATER OUTLET 1" BSP WATER INLET 1" BSP OIL DRAIN M18 x 1.5 -6H (100) (73) Ø MINIMUM ALLOWANCE FOR ELEMENT REMOVAL (898) FUEL RETURN M12 x 1.25 05 ECO - 1715, DRAWING REVISED TO SHOW THE UPDATED SOLENOID KIT AND U BOLT R.W 04/07/12 N.N 04/07/12 L.EDWARDS 04/07/12 06 ECO-2366, STOP SOLENOID OPTION REVISED FROM ASSP0010 TO ASSP0012. HEATSHIELD ASSEMBLY, BLOCK HEATER, & WIRING LOOM ADDED R.T. 12/05/15 S.R. 12/05/15 S.WAGHULE 12/05/15 1 9 6 C L 07 07 - POSITION BLOCK HEATER IN MIDDLE WELSH PLUG. - REMOVE ANY BURRS, SHARP EDGES, PAINT OR COMPOUND FROM THE SURFACE OF THE HOLE. - LUBRICATE BLOCK HEATER O RING & MACHINED SURFACE OF ENGINE BLOCK HOLE WITH A SMALL AMOUNT OF ANTI-FREEZE OR SILICONE GREASE. - WHEN INSTALLED, TORQUE CAPSCREW TO 14 Nm, SEE DRAWING No. 3826748 HEATER POSITIONED: 242mm FROM CL OF CRANK 254mm FROM RFOB - POSITION THERMOSTAT BEHIND FUEL FILTER (FUEL FILTER REMOVED FOR CLARITY). - APPLY PASTE TYPE THREAD SEALANT. THERMOSTAT POSITIONED: 340mm FROM CL OF CRANK 258mm FROM RFOB 07 BLOCK HEATER BLOCK HEATER THERMOSTAT 6 6 07 ECO-2366, PICTORIALLY REVISED TO SHOW BLOCK HEATER HARNESS & HEATSHIELD MODIFICATIONS R.T. 17/07/15 L.E. 17/07/15 S.WAGHULE 17/07/15 07
