8/10/2019 76-100016-001_print.pdf

1/158

PEGAsys™Intelligent Suppression Control

and Fire Alarm System

Installation,Operation and

Maintenance Manual

July 2003P/N 76-100016-001

R

LISTED

FM

 PPROVE

UL Listing File No. S2422 Factory Mutual Approval J.I. No. OB2A6.AY

8/10/2019 76-100016-001_print.pdf

2/158

8/10/2019 76-100016-001_print.pdf

3/158

PEGAsys™Intelligent Suppression Control

and Fire Alarm System

Installation,Operation and

Maintenance Manual

July 2003P/N 76-100016-001

8/10/2019 76-100016-001_print.pdf

4/158

THIS PAGE INTENTIONALLY LEFT BLANK.

8/10/2019 76-100016-001_print.pdf

5/158

i

FOREWORD

TERMS AND ABBREVIATIONS

AC Alternating Current

ADA Americans with Disabilities Act

AH Ampre Hour

AI Addressable Contact Input Device

AO Addressable Relay Output Device

AST Alarm Simulation TestATM Annunciator Terminal Module

BIP Broadcast Indexed Protocol

BPM Beats Per Minute

CCM Central Control Module

CCP Central Control Panel

DC Direct Current

EDP Electronic Data Processing

EOC Event Output Control

ESD Electrostatic Discharge

FCP Fire Control Panel

GUI Graphical User Interface

HSSD High-Sensitivity Smoke Detector

HVAC Heating, Ventilating and Air Conditioning

I/O Input/Output

ID Identification

IRI Industrial Risk Insurers

LCD Liquid Crystal Display

LED Light Emitting Diode

ML Multi-Loop

NC Normally Closed

Note: This Manual Is To Be Used By Trained Distributors Only

This manual is intended to clearly and accurately reflect the PEGAsys Fire Alarm/Suppression Control System.

This publication describes the operation, installation and maintenance of the PEGAsys Fire Alarm/SuppressionControl System, P/Ns 76-100000-501 for Single-Loop System and 76-100000-600 for Multi-Loop System.

NCCM Networkable Central Control Module

NIC Network Interface Card

NFPA National Fire Protection Agency

NO Normally Open

NR Not Registered

NYC New York CityP/N Part Number

PALM PEGAsys Addressable Loop Module

PAS Positive Alarm Sequence

PC Personal Computer

PCB Printed Circuit Board

PCS PEGAsys Configuration Software

PC Line Power/Communication Line (RX/TX Loo

PS Power Supply

RCU Remote Control Unit

RDCM Remote Display Control Module

RDM Remote Display Module

RTC Real-Time Clock

RX/TX Receive Transmit

SL Single-Loop

SLC Signaling Line Circuit

SPDT Single Pole, Double Throw

UL Underwriter Laboratories

V Volts

Vac Voltage Alternating Current

Vdc Voltage Direct Current

8/10/2019 76-100016-001_print.pdf

6/158

ii

ACCEPTANCES, APPROVALS AND CERTIFICATIONS

PEGAsys Single-Loop System (P/N 76-100000-501)

UL: Underwriters Laboratories Listing File Number S2422.

• FM: Factory Mutual Engineering Corp. (Factory Mutual System) Approval J.I. Number 3005511

• CSFM: California State Fire Marshal Listing Number 7165-1076:146.

• NYC: City of New York Listing Number MEA 454-91-E Vol.III.

PEGAsys Multi-Loop System (P/N 76-100000-600)

• UL: Underwriter’s Laboratories Listing File Number S2422.

• FM: Factory Mutual Engineering Corp. (Factory Mutual System) Approval J.I. Number 3005511

• CSFM: California State Fire Marshal Listing Number 7165-1076:146.

• NYC: City of New York Listing Number MEA 454-91-E Vol.III.

8/10/2019 76-100016-001_print.pdf

7/158

iii

Foreword ................................................................................................................................... iTerms and Abbreviations ........................................................................................................... iAppendices ................................................................................................................................vii

List of Illustrations...................................................................................................................... viiiList of Tables ............................................................................................................................. x

Safety Summary ........................................................................................................................ xi

PARAGRAPH TITLE PAGE

TABLE OF CONTENTS

1 General Information ................................................................................................................1-11-1 Introduction ................................................................................................................................1-1

1-1.1 System Description.................................................................................................................... 1-11-1.2 System Components .................................................................................................................1-1

1-2 Component Description ............................................................................................................. 1-21-2.1 Central Control Module (CCM) ..................................................................................................1-2

1-2.2 Display Module .......................................................................................................................... 1-21-2.3 Receiver/Transmitter Module (RX/TX) ...................................................................................... 1-21-2.4 Power Supply/Charger Assembly .............................................................................................. 1-2

1-2.5 Basic Motherboard .................................................................................................................... 1-3

1-2.6 Multi-Loop Motherboard ............................................................................................................1-31-2.7 Output Modules ......................................................................................................................... 1-31-2.7.1 Signal Output Module ................................................................................................................ 1-4

1-2.7.2 Relay Output Module ................................................................................................................. 1-41-2.7.3 Agent Release Output Module ................................................................................................... 1-4

1-2.7.4 City-Tie Module.......................................................................................................................... 1-41-2.8 Remote Display/Control Modules .............................................................................................. 1-51-2.9 ATM Series Driver Modules ....................................................................................................... 1-5

1-2.10 Network Interface Card ............................................................................................................. 1-51-2.11 Standby Batteries....................................................................................................................... 1-6

1-2.12 Intelligent Loop Devices ............................................................................................................ 1-61-2.12.1 SmartOne Ionization Detector ................................................................................................... 1-6

1-2.12.2 SmartOne Photoelectric Detector.............................................................................................. 1-6

1-2.12.3 SmartOne Heat Detector ........................................................................................................... 1-61-2.13 SmartOne Detector Bases ........................................................................................................1-6

1-2.14 Addressable Contact Input Device ............................................................................................1-61-2.15 Addressable Relay Output Device ............................................................................................. 1-7

1-2.16 Model DH-2000 Air Duct Housing.............................................................................................. 1-71-2.17 Loop Isolator Devices ................................................................................................................ 1-7

1-2.18 ORION XT Interface Module ..................................................................................................... 1-71-2.19 Addressable AlarmLine Module .................................................................................................1-81-2.20 Addressable Signal/Sounder Module ........................................................................................1-8

1-3 System Specification .................................................................................................................1-8

2 Operation .................................................................................................................................2-12-1 Introduction ................................................................................................................................ 2-1

2-1.1 Modes of Operation ................................................................................................................... 2-12-2 Controls and Indicators..............................................................................................................2-12-2.1 LCD Display............................................................................................................................... 2-1

2-2.2 Audible Device...........................................................................................................................2-32-3 System Security.........................................................................................................................2-3

2-3.1 Levels of Security ...................................................................................................................... 2-32-3.2 Default Passwords.....................................................................................................................2-3

2-3.3 Entering Passwords ................................................................................................................... 2-32-4 System Power-Up ...................................................................................................................... 2-32-5 System Menus ...........................................................................................................................2-4

2-5.1 Menu Structure .......................................................................................................................... 2-4

8/10/2019 76-100016-001_print.pdf

8/158

iv

TABLE OF CONTENTS (cont.)

PARAGRAPH TITLE PAGE

2-5.2 Accessing the System Menus ...................................................................................................2-42-5.3 Exiting the System Menus .........................................................................................................2-42-5.4 Menu Functions ......................................................................................................................... 2-4

2-5.4.1 Isolate Menu Function ............................................................................................................... 2-4

2-5.4.2 List Menu Function ....................................................................................................................2-72-5.4.3 Set Menu Function ....................................................................................................................2-72-5.4.4 Test Menu Function ................................................................................................................... 2-7

2-6 Modes of Operation ................................................................................................................... 2-72-6.1 Normal Standby Mode ............................................................................................................... 2-72-6.2 Active Alarm Mode.....................................................................................................................2-7

2-6.2.1 Alarm Mode Indications .............................................................................................................2-72-6.2.2 Alarm Mode User Action ............................................................................................................ 2-7

2-6.3 Active Supervisory Mode ...........................................................................................................2-102-6.3.1 Supervisory Mode Indication ..................................................................................................... 2-10

2-6.3.2 Supervisory Mode User Action .................................................................................................. 2-112-6.4 Active Trouble Mode.................................................................................................................. 2-112-6.4.1 Trouble Mode Indications ..........................................................................................................2-11

2-6.4.2 Trouble Mode User Action .........................................................................................................2-112-7 Printing Operation ...................................................................................................................... 2-12

2-8 System Programming ................................................................................................................ 2-122-8.1 EOC Programming ....................................................................................................................2-12

2-8.1.1 Listing EOC Programming ......................................................................................................... 2-122-8.2 RTC Programming .................................................................................................................... 2-122-8.2.1 Listing RTC Programming ......................................................................................................... 2-12

2-8.2.2 Enable/Disable RTC Program Line Numbers ............................................................................ 2-132-8.3 Types of Inputs and Outputs ...................................................................................................... 2-13

2-8.3.1 System Inputs ............................................................................................................................ 2-132-8.3.2 Remote Control Unit (RCU) .......................................................................................................2-13

2-8.3.3 RX/TX Loops ............................................................................................................................. 2-132-8.3.4 System Outputs ......................................................................................................................... 2-132-8.3.5 System Output Modules ............................................................................................................2-13

2-8.4 Addressing Output Modules ......................................................................................................2-132-8.5 Registering Output Module Assignments................................................................................... 2-14

2-8.5.1 Listing Output Module Assignment ............................................................................................2-142-8.6 Addressing RCUs ...................................................................................................................... 2-14

2-8.7 Registering RCUs...................................................................................................................... 2-152-8.7.1 Detector Registration .................................................................................................................2-15

2-8.7.2 Addressable Monitor Module Registration ................................................................................. 2-152-8.7.3 Remote Control Module Registration.........................................................................................2-162-8.7.4 Listing all Registered RCUs....................................................................................................... 2-16

2-8.7.5 De-Registering RCUs ................................................................................................................2-16

3 Functional Description............................................................................................................3-13-1 Introduction ................................................................................................................................3-13-2 Block Diagram ...........................................................................................................................3-13-3 Functional Descriptions ............................................................................................................. 3-2

3-3.1 Central Control Module ..............................................................................................................3-23-3.2 Receiver/Transmitter Module (RX/TX) ......................................................................................3-3

3-3.3 Power Supply/Charger Assembly .............................................................................................. 3-43-3.4 Multi-Loop Motherboard ............................................................................................................3-5

3-3.5 Signal Output Module ................................................................................................................3-53-3.6 Relay Output Module .................................................................................................................3-63-3.7 Agent Release Output Module................................................................................................... 3-7

3-3.8 City-Tie Module..........................................................................................................................3-7

8/10/2019 76-100016-001_print.pdf

9/158

v

TABLE OF CONTENTS (cont.)

PARAGRAPH TITLE PAGE

3-3.9 Remote Display Control Modules .............................................................................................. 3-83-3.10 ATM Series Driver Modules ....................................................................................................... 3-83-3.11 Network Interface Card ............................................................................................................. 3-8

3-3.12 Field Devices .............................................................................................................................3-9

3-3.13 SmartOne Ionization Detector ................................................................................................... 3-93-3.14 SmartOne Photoelectric Detector.............................................................................................. 3-93-3.15 SmartOne Heat Detector ........................................................................................................... 3-9

3-3.16 Addressable Contact Input Device ............................................................................................3-93-3.17 Addressable Relay Output Device ............................................................................................. 3-103-3.18 Model DH-2000 Air Duct Housing.............................................................................................. 3-10

3-3.19 Loop Isolator Devices ................................................................................................................3-103-3.20 PEGAsys Addressable Loop Module (PALM) ............................................................................ 3-11

3-3.21 Addressable AlarmLine Module .................................................................................................3-113-3.22 Addressable Signal/Sounder Module ........................................................................................3-12

4 Maintenance Procedure ..........................................................................................................4-14-1 Introduction ................................................................................................................................4-1

4-2 Scheduled Maintenance ............................................................................................................4-14-3 Maintenance Procedures...........................................................................................................4-1

4-3.1 Lamp Test ..................................................................................................................................4-14-3.2 Loop Device Test ....................................................................................................................... 4-1

4-3.3 Battery Test................................................................................................................................4-24-3.4 Walk Test ...................................................................................................................................4-24-3.4.1 Walk Testing Detectors ..............................................................................................................4-2

4-3.4.2 Walk Test Procedure ................................................................................................................. 4-24-3.5 Alarm Simulation Test (AST) .....................................................................................................4-3

4-3.5.1 AST Procedure .......................................................................................................................... 4-34-4 Disarming and Rearming Release Circuits................................................................................4-3

4-4.1 Disarming Release Circuits ....................................................................................................... 4-44-4.2 Arming Release Circuits ............................................................................................................ 4-44-5 Powering Down the System....................................................................................................... 4-4

4-5.1 Power-Down Procedure ............................................................................................................4-44-6 Powering Up the System ...........................................................................................................4-4

4-6.1 Power-Up Procedure ................................................................................................................. 4-4

5 Troubleshooting and Corrective Maintenance ..................................................................... 5-15-1 Introduction ................................................................................................................................5-15-2 Standard Fault-Isolation Techniques.......................................................................................... 5-15-2.1 Visual Inspection ....................................................................................................................... 5-1

5-2.2 Power Checks ........................................................................................................................... 5-15-3 Troubleshooting ......................................................................................................................... 5-1

5-4 Removal and Replacement ....................................................................................................... 5-2

5-4.1 Required Tools ........................................................................................................................... 5-25-4.2 Central Control Module ..............................................................................................................5-25-4.3 RX/TX Module ........................................................................................................................... 5-25-4.4 Field Devices ............................................................................................................................. 5-3

6 Parts List .................................................................................................................................. 6-16-1 Introduction ................................................................................................................................6-1

7 Installation ................................................................................................................................7-17-1 Introduction ................................................................................................................................7-17-2 Materials Required For Installation ............................................................................................ 7-1

8/10/2019 76-100016-001_print.pdf

10/158

vi

TABLE OF CONTENTS (cont.)

PARAGRAPH TITLE PAGE

7-3 Installation Procedure For Central Control Panel ...................................................................... 7-17-4 Installation Procedure For Expansion Enclosures .....................................................................7-17-5 Installation Procedure For Output Motherboard ........................................................................7-2

7-6 Installation Procedure For Rx/Tx Module (Multi-Loop Only) ......................................................7-2

7-7 Installation of Output Modules ...................................................................................................7-37-7.1 Signal Audible Output Module ...................................................................................................7-37-7.2 Relay Output Module .................................................................................................................7-4

7-7.3 Agent Release Module .............................................................................................................. 7-47-7.4 City-Tie Output Module ..............................................................................................................7-47-7.5 Power Supply/Charger Assembly .............................................................................................. 7-4

7-7.6 Power Supply/Charger Assembly, Expansion Enclosure ...........................................................7-47-7.7 Power Supply Communication Connections.............................................................................. 7-5

7-8 Connecting AC Power ...............................................................................................................7-57-9 Install And Connect DC Power ..................................................................................................7-6

7-9.1 Battery Enclosure ......................................................................................................................7-67-9.2 Batteries ....................................................................................................................................7-67-10 Field Device Connection To RX/TX Module...............................................................................7-6

7-10.1 Wiring the RX/TX PC Line ......................................................................................................... 7-67-11 Output Signal Connection .......................................................................................................... 7-8

7-12 External Power Failure Indicator Connection ............................................................................ 7-87-13 Detector Installation ................................................................................................................... 7-8

7-14 Setting and Adjusting Smoke and Heat Detector Sensitivities................................................... 7-87-14.1 Setting and Adjusting Smoke and Heat Detector Sensitivity Procedure ....................................7-97-15 Addressable Contact Input Device Installation ..........................................................................7-9

7-16 Addressable Relay Output Device Installation ...........................................................................7-97-17 Installation Checkout ................................................................................................................. 7-10

7-18 Connection of Peripherals .........................................................................................................7-107-18.1 Connecting a Terminal or Personal Computer........................................................................... 7-10

7-18.2 Connecting a Printer .................................................................................................................. 7-10

8/10/2019 76-100016-001_print.pdf

11/158

vii

A Power Supply Requirements ..................................................................................................... A-1B System Expansion .....................................................................................................................B-1C Releasing Applications ..............................................................................................................C-1

D Reserved for Future Use ...........................................................................................................D-1

E Factory Mutual Sprinkler Requirements for Pre-Action and Deluge Type Sprinkler Systems ....E-1F Glossary ....................................................................................................................................F-1G Display Abbreviations ................................................................................................................ G-1

H Wiring Requirements for PEGAsys Signaling Line Circuit RX/TX ............................................. H-1I System Drawings.......................................................................................................................I-1J PEGAsys Network Interface Card ............................................................................................. J-1

K Addressable Signal/Sounder Module ........................................................................................K-1L Remote Display Control Module and Remote Display Module ..................................................L-1

M Addressable AlarmLine Module ................................................................................................. M-1N Networkable Central Control Module (NCCM)...........................................................................N-1

O Central Station Operation .......................................................................................................... O-1

LIST OF APPENDICES

APPENDIX TITLE PAGE

8/10/2019 76-100016-001_print.pdf

12/158

viii

LIST OF ILLUSTRATIONS

FIGURE TITLE PAGE

1-1 PEGAsys System, Overall Diagram ..........................................................................................1-01-2 Central Control Module (CCM) ..................................................................................................1-21-3 Display Module Assembly..........................................................................................................1-2

1-4 Receiver/Transmitter Module (RX/TX) ......................................................................................1-2

1-5 Power Supply/Charger Assembly .............................................................................................. 1-31-6 Basic Motherboard .................................................................................................................... 1-31-7 Multi-Loop Motherboard ............................................................................................................1-3

1-8 Signal Output Module ................................................................................................................ 1-41-9 Relay Output Module ................................................................................................................. 1-41-10 Agent Release Output Module...................................................................................................1-4

1-11 City Tie Module ..........................................................................................................................1-41-12 RDCM Keypad ...........................................................................................................................1-5

1-13 Module Mounting Dimensions ...................................................................................................1-51-14 Network Interface Card ............................................................................................................. 1-5

1-15 Battery Enclosure ...................................................................................................................... 1-61-16 SmartOne Detection Device ......................................................................................................1-61-17 4-inch Detector Base .................................................................................................................1-6

1-18 6-inch Detector Base .................................................................................................................1-61-19 Addressable Contact Input Device ............................................................................................1-6

1-20 Addressable Relay Output Device .............................................................................................1-71-21 Air Duct Housing........................................................................................................................1-7

1-22 Loop Isolator, Stand-Alone......................................................................................................... 1-71-23 Loop Isolator, RX/TX Mount ......................................................................................................1-71-24 Loop Isolator, 6-inch Detector Base Mount................................................................................1-7

1-25 PALM Interface Module for ORION XT HSSD ...........................................................................1-71-26 Addressable AlarmLine Module ................................................................................................. 1-8

1-27 Addressable Signal/Sounder Module ........................................................................................ 1-8

2-1 System Front Panel ................................................................................................................... 2-12-2 Menu Structure ..........................................................................................................................2-52-3 Active Alarms Example .............................................................................................................. 2-7

2-4 Supervisory Example for Supervisory Mode Indication ............................................................. 2-112-5 Active Troubles and Pre-Alarms Example .................................................................................2-11

2-6 Output Module Address Scheme ...............................................................................................2-132-7 RCU Registration Screen .......................................................................................................... 2-15

3-1 Overall Block Diagram, Single-Loop System............................................................................ 3-1

3-2 Overall Block Diagram, Multi-Loop System ............................................................................... 3-13-3 Central Control Module, Details................................................................................................. 3-23-4 Receiver/Transmitter Module, Details........................................................................................ 3-3

3-5 Power Supply/Charger Assembly Details .................................................................................. 3-43-6 Multi-Loop Motherboard, Details................................................................................................ 3-5

3-7 Signal Output Module, Details ...................................................................................................3-63-8 Relay Output Module, Details .................................................................................................... 3-7

3-9 Agent Release Output Module, Details ...................................................................................... 3-73-10 City Tie Module, Details ............................................................................................................. 3-83-11 RDCM Keypad ...........................................................................................................................3-8

3-12 ATM Module ..............................................................................................................................3-83-13 Network Interface Card ............................................................................................................. 3-8

3-14 Typical Detector.........................................................................................................................3-93-15 Addressable Contact Input Device ............................................................................................3-10

3-16 Addressable Relay Output Device .............................................................................................3-10

8/10/2019 76-100016-001_print.pdf

13/158

ix

LIST OF ILLUSTRATIONS (cont.)

FIGURE TITLE PAGE

3-17 DH-2000 Air Duct Housing ........................................................................................................ 3-103-18 Loop Isolator, RX/TX Mount ......................................................................................................3-113-19 Loop Isolator, Stand-Alone ......................................................................................................... 3-11

3-20 Loop Isolator, 6-inch Detector Base Mount................................................................................ 3-11

3-21 PALM Interface Module for ORION XT HSSD...........................................................................3-113-22 Addressable AlarmLine Module ................................................................................................. 3-113-23 Addressable Signal/Sounder Module ........................................................................................ 3-12

5-1 Single Loop Installation.............................................................................................................. 5-25-2 Multi-Loop Installation ................................................................................................................ 5-2

7-1 CCP Installation Drawing ...........................................................................................................7-1

7-2 Back Plate, Output Motherboard and Four Power Supplies ......................................................7-27-3 Back Plate, Eight Power Supplies .............................................................................................7-2

7-4 Back Plate, Two Output Motherboards ...................................................................................... 7-27-5 Installation for Multi-Loop .......................................................................................................... 7-37-6 Power Supply/Charger Wiring Diagram..................................................................................... 7-4

7-7 Power Supply/Charger Wiring Diagram for Expansion Enclosure ............................................7-57-8 RS-485 Connection ................................................................................................................... 7-5

7-9 Battery Enclosure ...................................................................................................................... 7-67-10 Conduit to CCP..........................................................................................................................7-6

7-11 Shielded Wire to CCP ...............................................................................................................7-77-12 Style 4, RX/TX PC Line Connections......................................................................................... 7-77-13 Style 6, RX/TX PC Line Connections......................................................................................... 7-7

7-14 Style 6, RX/TX PC Line Connections with Loop Isolators..........................................................7-87-15 Style 7, RX/TX PC Line Connection ..........................................................................................7-8

7-16 CCM Printer Port ....................................................................................................................... 7-10

8/10/2019 76-100016-001_print.pdf

14/158

x

LIST OF TABLES

TABLE TITLE PAGE

1-1 System Specifications................................................................................................................1-8

 2-1 Controls and Indicators.............................................................................................................. 2-2

 2-2 Isolate Menu Function ...............................................................................................................2-8

 2-3 List Menu Function .................................................................................................................... 2-8 2-4 Set Menu Function .................................................................................................................... 2-9

 2-5 Test Menu Functions ................................................................................................................. 2-10

 3-1 Multi-Loop Motherboard Connectors .........................................................................................3-5 3-2 Approved Release Output Devices............................................................................................ 3-7

 5-1 Troubleshooting Index ...............................................................................................................5-1 5-2 RX/TX Configuration Selection .................................................................................................. 5-3

 6-1 PEGAsys System Parts List ......................................................................................................6-1

 7-1 RX/TX Configuration Selection .................................................................................................. 7-3

 7-2 Aux. Power Supply Module Connections to Main Power Supply/Charger Assembly ................. 7-5

8/10/2019 76-100016-001_print.pdf

15/158

xi

SAFETY SUMMARY

Note: Installation Precautions– Adherence to the following will aid in problem-free installation with long-term reliability

WARNING!

Several different sources of power can be connected to this fire alarm control panel.  Disconnect all

sources of power before servicing. Control unit and associated equipment may be damaged by removingand/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt toinstall, service, or operate this unit until this manual is read and understood.

CAUTION!

System Reacceptance Test after Software Changes:   To ensure proper system operation, this productmust be tested in accordance with NFPA-72 (2002) Chapter 10 after any programming operation or changein site-specific software. Reacceptance testing is required after any change, addition or deletion of systemcomponents, or after any modification, repair or adjustment to system hardware or wiring.

All components, circuits, system operations, or software functions known to be affected by a changemust be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices,

must also be tested and proper system operation verified.This system meets NFPA requirements for operation at 0° to 49° C and at a relative humidity of 85% (non-condensing) @ 30°C. However, the useful life of the system’s standby batteries and the electroniccomponents may be adversely affected by extreme temperature and humidity variations. Therefore, it isrecommended that this system and its peripherals be installed in an environment with a nominal roomtemperature of 60° to 80°F.

Like all solid state electronic devices, this system may operate erratically or can be damaged whensubjected to lightning induced transients. Although no system is completely immune from lightningtransients and interference, proper grounding will reduce susceptibility. The use of overhead or outside aerial wiring is not recommended due to the increased susceptibility to nearby lightning strikes. Consultwith the Applications Engineering Department if any problems are anticipated or encountered.

Disconnect AC power and batteries prior to removing or inserting circuit boards. Failure to do so candamage circuits.

Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of the enclosure.When possible, make all cable entries from the sides. Before making modifications, verify that they willnot interfere with battery and printed circuit board location.

Do not over tighten screw terminals. Over tightening may damage threads, resulting in reduced terminalcontact pressure and difficulty with screw terminal removal.

This system contains static-sensitive components. Always ground yourself with a proper wrist strapbefore handling any circuits so that static charges are removed from the body. Use static suppressivepackaging to protect electronic assemblies removed from the control unit.

Follow the instructions in the installation, operating, and programming manuals. These instructions must

be followed to avoid damage to the control panel and associated equipment. System operation andreliability depend upon proper installation.

FIRE ALARM SYSTEM LIMITATIONS

Note: While installing a fire alarm system may make lower insurance rates possible, it is not a substitute for fire insuance!

An automatic fire alarm system—typically made up of smoke detectors, heat detectors, manual pull stations, audib

warning devices, and a fire alarm control unit with remote notification capability—can provide early warning of a develoing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fir

8/10/2019 76-100016-001_print.pdf

16/158

xii

Any fire alarm system may fail for a variety of reasons:

Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in walls, or roofs, or

on the other side of closed doors. Smoke detectors also may not sense a fire on another level or floor of a building. Asecond floor detector, for example, may not sense a first floor or basement fire. Furthermore, all types of smoke detec-tors—both ionization and photoelectric types—have sensing limitations. No type of smoke detector can sense every kind

of fire caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper stor-age of flammable materials, overloaded electrical circuits, children playing with matches or arson.

Audible warning devices such as bells may not alert people if these devices are located on the other side of closed or

partly open doors or are located on another floor of a building.A fire alarm system will not operate without electrical power. If AC power fails, the system will operate from standby

batteries only for a specified time.

Rate-of-rise heat detectors may be subject to reduced sensitivity over time. For this reason, the rate-of-rise feature ofeach detector should be tested at least once per year by a qualified fire protection specialist.

Auxiliary equipment used in the system may not be technically compatible with the control panel. It is essential to use onlyequipment listed for service with your control panel.

Telephone lines needed to transmit alarm signals from a premise to a central monitoring station may be out of service or

temporarily disabled.

The most common cause of fire alarm malfunctions, however, is inadequate maintenance. All devices and system wiringshould be tested and maintained by professional fire alarm installers following written procedures supplied with each

device. System inspection and testing should be scheduled monthly or as required by national and/or local fire codes.Adequate written records of all inspections should be kept.

GENERAL SAFETY NOTICES

Note: The following must be observed to maintain personnel safety.

The following general safety notices supplement specific warnings and cautions appearing in the manual. The safetyprecautions in this section must be understood and applied during operation and maintenance. This manual is to be used

by trained distributors/technicians. The entire manual should be read and fully understood prior to installation.

TEST EQUIPMENT

Make certain test equipment is in good operating condition. Do not touch live equipment or personnel working on live

equipment while holding a test meter. Some types of measuring devices should not be grounded; these devices shouldnot be held when taking measurements.

FIRST AID

Any injury, no matter how slight, should never go unattended. Always obtain first aid or medical attention immediately.

GENERAL PRECAUTIONS

The following general safety precautions are to be observed at all times:

1. All electrical components associated with equipment shall be installed and grounded in accordance with NEC, NFPAand local regulatory requirements.

2. Special precautionary measures are essential to prevent applying power to equipment at any time maintenance workis in progress.

3. Before working on electrical equipment, use a voltmeter to ensure that the system is not energized.4. When working near electricity, do not use metal rulers, flashlights, metallic pencils or any other objects having ex-

posed conductive material.

5. When connecting a meter to terminals for measurement, use voltage range higher than the expected voltage.

8/10/2019 76-100016-001_print.pdf

17/158

THIS PAGE INTENTIONALLY LEFT BLANK.

8/10/2019 76-100016-001_print.pdf

18/158

January 2002

PEGAsys™ 

1-0 76-100016-001

   F   i  g  u  r  e   1  -   1

 .     P     E     G     A    s    y    s   S  y  s   t  e  m ,   O  v  e  r  a   l   l   D   i  a  g  r  a

  m

    A    d    d   r   e   s   s   a

    b    l   e    S   u   p   p   r   e   s   s

    i   o   n

    S   y   s

    t   e   m

    A    b   o   r    t

    D   e   v

    i   c   e

     P     U     S     H

     /     H     O     L     D

     S     U     P     P     R     E     S     S     I     O     N

     S     Y     S     T     E     M

     A     B     O     R     T

     P     U     S     H

     P     U     L     L

    R

     F     I     R     E

     A     L     A     R     M

     F     I     R     E

     A     L     A     R     M

    R    S

  -    4    8    5

    A    l   a   r   m

    N   o    t    i    f    i   c   a

    t    i   o   n

    A   p   p    l    i   a

   n   c   e   s

8/10/2019 76-100016-001_print.pdf

19/158

1-1 July 20

PEGAsys™

76-100016-001

CHAPTER 1

GENERAL INFORMATION

1-1 INTRODUCTION

This manual contains the operation, maintenance, trouble-shooting, parts listing and installation information neces-

sary to support the PEGAsys™   Intelligent SuppressionControl and Fire Alarm System.

Note: This manual is to be used by trained distributorsonly. The entire manual should be read and fully

understood prior to installation. Refer to Figure 1-1 for the PEGAsys System overall diagram.

1-1.1 System Description

PEGAsys is a fire alarm/suppression control system whichcan be used for local, auxiliary, remote protective signal-

ing and releasing device service. The system is a micro-processor based design for use with intelligent detectors

and loop devices.

The system utilizes distributed intelligent field devices.

These devices are typically smoke detectors, contact in-put devices, relay outputs and signal output modules which

represent a single fire alarm initiation/indicating zone. Eachdevice contains its own data transceiver, micro controller,

4K of memory and applicable algorithms which allows eachdevice to operate independently of the control system.

These unique devices have the ability to analyze informa-tion, make decisions and store information within them-

selves. They communicate with the PEGAsys system usingthe BIP protocol which utilizes a two-wire (Style 4), fourwire (Style 6) or isolated (Style 7) multiplex trunk. The

PEGAsys can support up to 255 device addresses per loop,with a maximum of eight (8) loops, for a total of 2,040 in-

telligent device points per system.

The PEGAsys is capable of controlling a wide variety of

auxiliary devices, such as relays, audible/visual indicatingsignal devices and agent/sprinkler release systems. The

system also supports the use of serial printers which pro-vide hard copy of system status information.

There are three versions of the PEGAsys currently in ser-

vice. These three versions are identified as:

• Pre-Network,

• Networkable, and

• Networkable and directly-integrable with ORION™XT High-Sensitivity Smoke Detectors (HSSDs).

Pre-networked systems have operating firmware in the

Central Control Module (CCM) that ranged from Version48.0 to Version 6X.X. All pre-networked systems must now

have Version 60.0, or higher, operating firmware. Pre-neworked systems are not covered in this manual.

Networkable systems have a modified CCM that can acept a Network Interface Card (NIC) for peer-to-peer co

trol unit operations, and can accommodate Remote DisplaModules (RDMs), Remote Display Control Module

(RDCMs) and ATM Series Driver Modules (ATM-L/RNetworkable systems have CCM Version 7X.X firmware

Networkable systems that are directly-integrable wiORION XT HSSDs have Version 8X.X CCM firmware.

1-1.2 System Components

The system is comprised of three major components, ashown in Figure 1-1: the Central Control Panel (CCP) whic

communicates with the field devices and drives outpdevices such as alarm signals that communicate with ce

tral stations and various types of control equipment; a dplay panel located on the CCP that provides system statu

LEDs and Control Switches; and an 80-character LCD thprovides alphanumeric display of system status informtion.

The single-loop PEGAsys Central Control Panel (P

76-100000-501) consists of the Central Control Modu(CCM) assembly, one receiver/transmitter (RX/TX) mo

ule and one power supply assembly. Optionally the sytem can add a motherboard assembly which allows for th

installation of optional output modules. An auxiliary powsupply module can be added which increases the bassystem power supply capacity to 8.0 Amps at 24 Vdc.

In multi-loop form, the PEGAsys  ML panel (P/N 76-10000

600) consists of a CCM, one (1) power-supply assembone (1) RX/TX module and one (1) multi-loop motherboa

mounted in the enclosure. The unique multi-loomotherboard provides the ability to connect up to eight (RX/TX modules to the system which allows for a full 2,04

addressable points to be connected to the PEGAsys Msystem.

Auxiliary enclosures are available to allow the system

be expanded. The auxiliary enclosure has the same dmensions as that of the main enclosure, with the absencof the window in the door. There are optional backplane

that install in the expansion enclosure. This allows the number of output modules and system power supplies to b

expanded. To allow for maximum system flexibility and epansion, enclosure(s) and backplane(s) can be added the system. See Appendix B for further system expansio

details.

8/10/2019 76-100016-001_print.pdf

20/158

1-2July 2003 76-100016-001

PEGAsys™

1-2 COMPONENT DESCRIPTION

The following paragraphs give a brief description of eachcomponent used in the PEGAsys system. For functional

descriptions of each component, see Chapter 3 of thismanual.

1-2.1 Central Control Module (CCM)

The CCM assembly is the heart of the system and is com-prised of two (2) printed circuit board (PCB) assemblies,

the display module and the main processor module. TheCCM controls the operation and supervision of all the sys-

tem modules and software within the PEGAsys system. Itreceives loop device data from the RX/TX module, pro-

cesses the data based on pre-programmed instructionsand transmits output commands to the output modules,field devices and display module(s).

1-2.2 Display Module

The display module assembly, attached to the main pro-cessor PCB, provides the system with the operator inter-

face for control switches, system status LEDs, systemtrouble/alarm buzzer, an 80-character (2 x 40) LCD dis-

play and an integral numeric keypad. The keypad is usedfor entering the security password and navigating through

the user menus. The system buzzer provides two (2) dis-tinctly different signaling patterns for audible warning ofsystem alarms and troubles.

PRE-ALARM

ALARM

AC POWER   SYSTEM TROUBLE

SUPERVISORY

SILENCE

SYSTEMACKNOWLEDGE

SYSTEMRESET

SILENCE

SCROLL

SYSTEM STATUS DISPLAY

R

Display ResetSwitch

      P      L       G       2 

      J       K       1 

      J       K       2 

      P      L       G       3 

      S       W      1 

      P      L       G       2 

      J       K       3 

      P      L       G       1 

PRINT PORT  DS1

      0       V

      2        4

      V      D       C 

      E       A      R       T      H

      F      A      U       L       T

      S       U       P      P      L       Y

      F      A      U       L       T

      T      B       6 

BUZZER

Processor Port

DisplayPort

PC Port

Display TroubleLED

24 Vdc fromPower Supply

Figure 1-2. Central Control Module (CCM)

PRE-ALARM

ALARM

AC POWER   SYSTEM TROUBLE

SUPERVISORY

SILENCE

SYSTEMACKNOWLEDGE

SYSTEMRESET

SILENCE

SCROLL

SYSTEM STATUS DISPLAY

 

Figure 1-3. Display Module Assembly

1-2.3 Receiver/Transmitter Module (RX/TX)

The RX/TX functions as the hardware and software inter-face between the field devices and the CCM. The RX/TX

receives control requests from the CCM, and establishescommunications with the field devices. The RX/TX receives

status changes from the field devices and reports thesechanges to the CCM. The RX/TX, shown in Figure 1-4, iscapable of communicating with up to 255 intelligent de-

vices and complies with the wiring requirements of NFPA

Style 4, 6 and 7 (with the use of the loop isolator devices).Style 4 initiation circuit wiring will permit “T” tapping orbranch circuitry.

1-2.4 Power Supply/Charger Assembly

The power supply/charger assembly (P/N 76-100009-010)is comprised of a PCB assembly and an AC/DC switching

power supply unit. The switching power supply unit pro-vides 4 Amps of 24 Vdc from the 120/240 Vac input power.The PCB assembly is a microprocessor based unit which

provides the system with:

• Battery charging and supervision

• AC power supervision

• 24 Vdc supervision

• Battery load test

• 24 Vdc ground fault detection (+/-)

• Auxiliary 24 Vdc outputs

Loop Isolator for Style 7

Figure 1-4. Receiver/Transmitter Module (RX/TX)

8/10/2019 76-100016-001_print.pdf

21/158

1-3 July 20

PEGAsys™

76-100016-001

Figure 1-5. Power Supply/Charger Assembly1-2.5 Basic Motherboard

The basic motherboard assembly (P/N 76-100007-001) is

an assembly which can accept up to eight (8) output mod-ule circuit board assemblies. The motherboard is mounted

to the back of the system enclosure and/or the auxiliaryenclosures. It distributes 24 Vdc power and bus communi-

cations to the output modules. The bus communicationsare provided by an RJ-12 (flat phone cable) style connec-tion. The 24 Vdc is provided by the system power supply

via a two-conductor wiring harness. The motherboardmounts to standoffs on the back of the main and expan-

sion enclosures with screws which are provided.

R1 W1

J1 J2   J3   J4 J5 J6 J7 J8 TB1+24V

RET

TB2

485B

485A

SIG GND

COM ALM

COM TBL

J9

RS-485

Figure 1-6. Basic Motherboard

1-2.6 Multi-Loop Motherboard

The multi-loop motherboard assembly (P/N 76-100017-001) is an assembly which can accept up to eight (8)

RX/TX modules and provide connections for up to seven(7) output module circuit board assemblies. The ML

motherboard is mounted to standoffs on the back of themain system enclosure. It distributes 24 Vdc power, CCM-

RX/TX communications for up to eight (8) RX/TX mod-ules and bus communications to the output modules. Thebus communications are provided by an RJ-12 (flat phone

cable) style connection. A single RJ-12 connection con-nects the ML motherboard to the CCM for RX/TX commu-

nications. The 24 Vdc is provided by the system powersupply via a two-conductor wiring harness. The allowable

combinations of RX/TX and output modules that can bused with a Multi-Loop Motherboard are as follows:

)s(XT/XRfo.oN seludoMtuptuOfo.oN

2ro1 7 – 1

3 6 – 1

4 5 – 1

5 4 – 1

6 3 – 1

7 2 – 1

8 1

W1

J1 J3   J4   J5   J6   J7J2 TB9+24V

RET

T

485A

SIG GND

COM ALM

COM TBL

485B

JP1JP2JP3JP4JP5JP6JP7JP8

TB8 TB7   TB6   TB5 TB4 TB3 TB2   TB1

TB11

+24V

RET

JP1

RS-232

JP9RS-485

Figure 1-7. Multi-Loop Motherboard

1-2.7 Output Modules

The optional output modules allow the PEGAsys systeto interface with external auxiliary devices. These aux

iary devices can be audible/visual signal devices, HVAsystems, elevator recall, power shut down, remote annu

ciators, agent/sprinkler release system and any other cotrol type output which may need to be interfaced to th

system.

The output modules plug into the motherboard assemb

located on the backplate of the system enclosure. Eacmodule occupies one slot in a motherboard assembly. Th

modules and the CCM communicate over the RS-48based bus, which uses a six-conductor, phone-type cab

to connect the CCM to the motherboard.

The PEGAsys single-loop panel has the ability to suppo

a maximum of sixteen (16) output modules, in any combnation. However, no more than eight (8) of any one type

module can be used. The system is limited to one City-TModule.

The PEGAsys multi-loop panel has the ability to supportmaximum of twenty-three (23) output modules, in any com

bination in the system. However, no more than eight (8) any one type of module can be used, and the system

limited to one City-Tie Module.

The following paragraphs describe each available outpmodule in greater detail.

8/10/2019 76-100016-001_print.pdf

22/158

1-4July 2003 76-100016-001

PEGAsys™

1-2.7.1 SIGNAL OUTPUT MODULE

The PEGAsys panel has the capacity for a maximum ofeight (8) Alarm Sounder/Signal Output cards, thus provid-ing thirty-two (32) possible Class B, Style "Y" signal cir-

cuits. Each Alarm Sounder/Signal Output card is equippedwith supervised 24 Vdc outputs which can operate as Class

B, Style “Y” or Class A, Style “Z” indicating circuits (seeFigure 1-8).

7      6      -   1      

 0       0       0       0       3      -    0      

 0      1      

Figure 1-8. Signal Output Module

1-2.7.2 RELAY OUTPUT MODULE

The PEGAsys panel has the capacity for a maximum ofeight (8) Auxiliary Relay Output cards, allowing up to thirty-two (32) relays. Each Auxiliary Relay Output card is

equipped with four (4) Form C, dry-contact relay outputs.The ability to isolate an individual relay output is provided

through the system operator menu.

Figure 1-9. Relay Output Module

1-2.7.3 AGENT RELEASE OUTPUT MODULE

The PEGAsys panel has the capacity for a maximum ofeight (8) agent release output modules, providing up toeight (8) release circuits and twenty-four (24) signal out-

puts on those modules.

Figure 1-10. Agent Release Output Module

1-2.7.4 CITY-TIE MODULE

The City-Tie (Notification) Module will provide connectionand operation for local energy or shunt type master boxes

and reverse polarity styles of off-premises reporting.

7

6

 

1

 

2

 

1

Figure 1-11. City Tie Module

8/10/2019 76-100016-001_print.pdf

23/158

1-5 July 20

PEGAsys™

76-100016-001

1-2.8 Remote Display/Control Modules

The remote display control modules permit system eventsto be displayed, and operator intervention to be accom-plished, from more than one location in a facility. Two styles

of remote display modules are available; Model RDCM isa duplicate of the PEGAsys Display/Control Module and

allows full operator intervention and system control, whileModel RDM is a display-only module that only permits the

viewing of the current system events.

SYSTEM

RESET

ACKNOWLEDGESYSTEM

3

8

AC POWER

ALARM

PRE-ALARM

6

1

7

2

SUPERVISORY

SYSTEM TROUBLE

System Status Display

SILENCE

9

4

0

5

SILENCE

SCROLL

R

Figure 1-12. RDCM Keypad

1-2.9 ATM Series Driver Modules

The ATM Series Driver Modules permit third-party graphi-cal annunciators and large numbers of auxiliary relays to

be used with the PEGAsys Control Unit. Two types of drivermodules can be used, Models ATM-L and ATM-R.

The Model ATM-L Annunciator Driver Module provides the

PEGAsys Control Unit with up to 32 programmable, su-pervised LED outputs for graphical or tabular annuncia-tors, along with 6 system-level LED outputs and 5

system-level input circuits for functional switches.

The system-level LEDs correspond to the following gen-eral conditions: Module Power, Alarm, Pre-Alarm, Alarm

Silence, Supervisory, and Trouble.

The input circuits for functional switches provide for the

following operator intervention: System Reset, Event Ac-knowledgment, Alarm Silence, Fire Drill, and Lamp Test.

The Model ATM-R Relay Driver Module can activate up to

32 programmable, supervised relays.

The PEGAsys supports up to 16 ATM-L or ATM-R Driver

Modules, or any combination of these two modules, alongwith RDCMs and RDMs, that does not exceed 31 total

addresses.

16151413121110

9

87654321

Lamp TestCom

AckReset

SilenceDrill

3231302928272625

2423222120191817

LK19

LK21

LK18

LK20

LK23   LK22

L K2 5 L K2 4

L K2 7 L K2 6

L K2 9 L K2 8

L K3 1 L K3 0

LK32

LK17

LK15LK16

LK13LK14

LK11LK12

LK10

LK8

LK6

LK4

LK2

LK9

LK7

LK5

LK3

LK1

TroubleSup.

Sil. OutPre AlmAlarmPwr On

AB

+24 V

ComPS Flt

W1

Out BOut AIn B

In A

S2 S1

ATM-L/R

Earth Gnd

1.375 5.175

0.188

4.625

8.000

5.000

Note:

Maintain a minumum one-half (1/2) inch clearance around ATM-L

and ATM-R Modules when installed in mounting enclosure.

Figure 1-13. Module Mounting Dimensions

1-2.10 Network Interface Card

The Network Interface Card allows multiple PEGAsControl Units to be combined into an integrated, peer-t

peer network for annunciation, event output control, anoperator intervention.

KIDDE-FENWAL, INC.   ASHLAND, MA 01721

D

NETWORK INTERFACE CARDCAT. NO. 74-200036-001

TB3

B2IA2

TB4

B2NA2

TB2

B1NA1

TB1

B1IA1

U11

C26

U16

1

U17

1

RV2

RV1

RV3

R26

K1

U181

U201

      R      2      1

U21

1

R41

Q2

R40

Q3

      C       1      0 

      R      4      3 

      R      4      2

R18U61

U14

1

C8

R7

Q4

C9

U19   1

U151

Q1

C7

R1

R44

R17

      R      V      1      1

      R      2      4

      R      V      1      2

      E      8 

      R      V      1      0    RV8RV6

      E      4

      E      7

      R      2      5 

      R      5 

      R      6 

R20

R22

RV5

RV4

      E      3 

      E      2

      E      5 

      E      6 

      R      4

      R      3 

R36

RV9

RV7

K2

K4

      R      2      3 

CR2

K3

CR1

U5

1

      C       1      8 

      R      1      3 

      R      2

U4

1

U8

1

R29

R38

C24

R19

C17

+      

R27

U9

1

R32

R12

U10

1

R28

C22

C16

C15

R31

C25   C       1

      R      1      5 

      R      3       3 

R34

C14

      R      1      4

U2

1

      C       2      3 

U7

1

C20

+

      C       2

      E      1

C11

C5

C3   +   C4     +

R45

U13

1

R46

C27

U12

1

C12

      C       R      3 

Y1

TP

+5

TP

TP

TP

TP

U3

1

C13

R10

TP

GND

J1   DS2

N1

DS4

N2

DS3

I2

DS1

I1

Figure 1-14. Network Interface Card

8/10/2019 76-100016-001_print.pdf

24/158

1-6July 2003 76-100016-001

PEGAsys™

1-2.11 Standby Batteries

Space is provided within the central control panel enclo-sure for up to two (2) 12 V, 33 AH, sealed lead-acid batter-ies used for 24-, 60- or 90-hour standby operation. If

additional batteries are required, an optional battery en-closure is available. The enclosure (Figure 1-15) is a heavy

duty steel cabinet that can house up to two (2) 40 AH bat-teries. For installation information, see Paragraph 7-9.1.

STANDBY BATTERIES

FIRE ALARM SYSTEM

KIDDE

Figure 1-15. Battery Enclosure

1-2.12 Intelligent Loop Devices

The SmartOne ®  Series of Intelligent Fire Alarm Devices

provides the PEGAsys control system with smoke and heat

detection, and necessary monitoring and control functionsrequired by advanced fire alarm systems. The followingparagraphs describe each available intelligent detectiondevice.

Figure 1-16. SmartOne Detection Device1-2.12.1 SMARTONE IONIZATION DETECTOR

The SmartOne Ionization smoke detector provides true dis-

tributed-intelligence, addressable microprocessor-basedsmoke detection to the PEGAsys system.

1-2.12.2 SMARTONE PHOTOELECTRIC

DETECTOR

The SmartOne Photoelectric smoke detector provides true

distributed-intelligence, addressable microprocessor-based smoke detection to the PEGAsys system.

1-2.12.3 SMARTONE HEAT DETECTOR

The SmartOne Thermistor heat detector provides true dis-tributed-intelligence, addressable, microprocessor-based

heat detection to the PEGAsys system.

1-2.13 SmartOne Detector Bases

The SmartOne series of detection devices use universalmounting bases which are available in three styles:

1. The 4SB is a sub-floor style 4-inch base with an out-

side diameter that matches that of the low profileSmartOne detectors. The 4SB, shown in Figure 1-17,

mounts to standard 3 inch/3.5-inch, or 100mm electri-cal boxes.

Figure 1-17. 4-inch Detector Base

2. The 6SB model, shown in Figure 1-18, is a tradition-

ally styled detector base with an integral trim ring whichprovides coverage for any inconsistencies between theelectrical box and ceiling material. The 6SB mounts tostandard 3 inch/3.5 inch/4-inch electrical boxes.

Figure 1-18. 6-inch Detector Base

1-2.14 Addressable Contact Input Device

The SmartOne Contact Monitor (P/N 70-407008-00X) al-

lows an installer the ability to interface typical NO/NC firealarm devices (i.e., water flow and tamper switches) to the

PEGAsys system. The contact monitor is also used to in-terface to manual alarm, manual release and abort sta-

tions.

     M     O      D     E     L     A     I ,  

      N     /      O 

    I    N    S     T    R    U     C     T    I    O     N    S 

    S     E    E    I    N    S     T    A    L    L    A    T    I    O     N

    C     A    T

 .     N

    O  .     7

    0   -    4

    0     7    0     0     8 

  -    0     0     1

     S     m    a     r     t 

     O     n    e 

     T     M

    F    O     R    S     E    R    V    I    C     E    S     E    N    D    T    O    :

    K    I    D    D    E

  -    F    E    N    W    A    L

 ,      I    N

    C  .

    4    0     0 

     M    A    I    N    S     T

 .

    A    S     H    L    A    N    D

 ,      M

    A    0     1    7    2    1

    D    A    T    E    O     F

     M    A    N    U     F    A    C     T    U     R    E   :

    M    A    X

 .     I    N

    S     T    A    L    L

 .     T

    E    M    P

 .     1

    2    0     °    F

   7 6 5 4 3 2 1

    0     6 

  -    2    3     5     5     7    8 

  -    0     0     1

    P    C    P    C    P    C    P    C  (   +  )  (  -  )  (   +  )  (  -  )

   8

    A

    S     W

    B

    S     W  (   +  )   L    E    D

  (  -  )   L    E    D

    A    L    L

     T    E    R    M    I    N    A    L    S 

     A    R    E    P    O     W    E    R    L    I    M    I    T    E    D

Figure 1-19. Addressable Contact Input Device

8/10/2019 76-100016-001_print.pdf

25/158

1-7 July 20

PEGAsys™

76-100016-001

1-2.15 Addressable Relay Output Device

The addressable relay output device (P/N 70-408004-001)provides the PEGAsys system with a Form C dry-contactinterface for remote control applications.

     M     O      D     E     L     A     O 

    I    N    S     T    R    U     C     T    I    O     N    S 

    S     E    E    I    N    S     T    A    L    L    A    T    I    O     N

    C     A    T

 .     N

    O  .     7

    0   -    4

    0     8     0     0     4  -    0 

    0     1

     S     m    a     r     t 

     O     n    e 

     T     M

    F    O     R    S     E    R    V    I    C     E    S     E    N    D    T    O    :

    K    I    D    D    E  -    F

    E    N    W    A    L

 ,      I    N

    C  .

    4    0     0 

     M    A    I    N    S     T

 .

    A    S     H    L    A    N    D

 ,      M

    A    0     1    7    2    1

    D    A    T    E    O     F

     M    A    N    U     F    A    C     T    U     R    E   :

    M    A    X

 .     I    N

    S     T    A    L    L

 .     T

    E    M    P

 .     1

    2    0     °    F

   7 6 5   4 3 2 1

    0     6   -    2

    3     5     5     7    7  -    0 

    0     1

    P    C    P    C    P    C    P    C  (   +  )  (  -  )  (   +  )  (  -  )    N  /    C    C    O     M    N  /    O

    T    E    R    M    I    N    A    L    S     5 

  -    7    A    R    E    P    O     W    E    R    L    I    M    I    T    E    D

    T    E    R    M    I    N    A    L    S     1

  -    4    A    R    E    P    O     W    E    R    L    I    M    I    T    E    D

LED

Figure 1-20. Addressable Relay Output Device

1-2.16 Model DH-2000 Air Duct Housing

The DH-2000 air duct housing is designed for detectingparticles of combustion products in air-handling systems.

DUCT

DETECTOR

MODEL

DH-2000

R

Figure 1-21. Air Duct Housing

1-2.17 Loop Isolator Devices

The SmartOne series of loop isolation devices, shown inFigures 1-22 through 1-24, offer optional loop isolationwhich protects the loop from wire-to-wire short conditions

(NFPA Style 7.0).

Figure 1-22. Loop Isolator, Stand-Alone

L  O OP I    S  OL A T  OR

RX  /   T X 

KIDDE-FENWAL, INC.

 ASHLAND, MA 01721

    S    H    O    R    T  -  1    S    H    O    R    T  -   2

DS2 DS1

J1

FOR MODULE INSTALL.

P/N 76-100016-001

INSTALLATION MANUAL

REFER TO

PROCEDURES

Laboratories Inc.Underwriters

R

LISTED

R

Figure 1-23. Loop Isolator, RX/TX Mount

LaboratoriesUnderwriters

R

LISTED

Figure 1-24. Loop Isolator, 6-inch Detector Base Moun

1-2.18 ORION XT Interface Module

The PEGAsys Addressable Loop Module (PALM) permdirect connection of an ORION XT High-Sensitivity SmoDetector (HSSD) to a signaling line circuit of the PEGAs

Control Unit. The ORION XT reports pre-alarm, alarm antrouble status by individual location (i.e., address) to th

PEGAsys Control Unit via the PALM.

The PALM is housed within the ORION XT HSSD enclsure and plugs into a receptacle on the Detector's printecircuit board.

Figure 1-25. PALM Interface Module forORION XT HSSD

8/10/2019 76-100016-001_print.pdf

26/158

1-8July 2003 76-100016-001

PEGAsys™

Table 1-1. System Specifications

METI SCITSIRETCARAHC

ylppuSrewoP

:tnemeriuqeRrewoP* zH06 / 05,V022 / 021

)eludoMreP(tupnI.S.P  spmA9.1,caV021

spmA59.,caV022

)eludoMreP(tuptuO.S.P spmA4,cdV42

:tuptuOregrahC.taB spmA3,cdV4.62

)2(:stuptuO.xuA hcaespmA5.1,cdV42

MCC

:tuptuOlangiS spmA2,cdV42

:tuptuOesaeleR spmA2,cdV42

:gnitaRtcatnoCyaleR cdV03@pmA1

:gnitaRyaleRelbuorT cdV03@pmA1

eludoMXT/XR

:egatloV.xaM cdV4.62

:egatloV.niM cdV0.91

:ecnaticapaCeniL.xaM Fu52.0

:ecnatsiseReniL.xaM smhO62

elbasserddA.xaM

:seciveD  XT / XRrep552

eludoMesaeleR

tuptuOesaeleR cdV42@spmA2

tuptuOlangiS hcaecdV42@spmA2

:epyTtuptuOesaeleR  sdionelosgnisaelerfoelbapaC

)relknirpsdnanoisserppus(

eludoMelbiduAlangiS

:stuptuOlangiS

ro"Y"elytS,BssalC)4(

"Z"elytSAssalC)2(hcaecdV42@spmA2

eludoMyaleR

:gnitaRtcatnoC

,stcatnoCCmroF)4(

rocdV03@spmA2caV021@pmA1

eludoMeiTytiC

:tcatnoCtnuhS evitsiseR,cdV42@spmA5

:tuptuOygrenElacoL  ,cdV42@.xamAm005

detimiLtnerruC

:yrosivrepuSygrenElacoL Am11

:daoLygrenElacoL  tnerruCpirTxoBretsaM

lacipytspmA52.0

CAdnarewopmetsyslatotrofAxidneppAotrefeR:etoN*

.stnemeriuqertiucrichcnarb

1-2.19 Addressable AlarmLine Module

The Addressable AlarmLine Module (AAM) permits anAlarmLine sensor cable to be directly interfaced to thePEGAsys Control Unit. The AAM transmits pre-alarm,

alarm, and trouble signals to the Central Control Modulevia the RX/TX’s signaling line circuit. Alternatively, the AAM

can be configured to transmit an overheat signal to theControl Unit for those applications that require excessively-

high temperature indications.

TM

Figure 1-26. Addressable AlarmLine Module

1-2.20 Addressable Signal/Sounder Module

The Addressable Signal/Sounder Module (ASM) permits

notification appliances to be controlled via commands is-sued from the PEGAsys Control Unit’s signaling line cir-

cuit. The ASM is designed to mount in a standard electricalbox.

 A B B A

-+-+ + - - +

KIDDE-FENWAL, INC.

 ASHLAND, MA 01721 U.S.A.CAT. NO. 70-200200-001INSTRUCTIONS P/N 06-235717-001

 ALL OTHERS - POWER LIMITED

DEVICE

 ADDRESS # _ _ _ _  AUX./AUDIO MODE

SETTINGS

PC LINE TERMINALS - POWER LIMITED

 ADDRESSABLE SIGNAL/SOUNDER MODULE (ASM)

 _ _ _ _ 

INSTRUCTIONS P/N 06-235717-001

 ADDRESS #SETTINGS

 AUDIO

P1=1&2MODE

S1=3 ON

 AUX. INUX.IN

+ - + -TROUBLE

CKT. -OUTPUTCKT.

-+ +

 AUX./AUDIO MODE

 AUXILIARY

MODEP1=2&3S1=1&2 ON

PC LINECLINE

 A B A B

DEVICE

 ALL OTHERS - POWER LIMITED

CAT. NO. 70-200200-001 ASHLAND, MA 01721 U.S.A.

KIDDE-FENWAL, INC.

FM

 APPROVED

R LU

TM

Figure 1-27. Addressable Signal/Sounder Module

1-3 SYSTEM SPECIFICATION

System power specifications are outlined in Table 1-1.

8/10/2019 76-100016-001_print.pdf

27/158

PEGAsys™

July 2076-100016-001 2-1

CHAPTER 2

OPERATION

2-1 INTRODUCTION

This chapter describes the PEGAsys™ system controlsand indicators located on the display panel. It also describes

the operating procedures and menu system.

2-1.1 Modes of Operation

There are two modes of PEGAsys system operation:

1. In the default operation, the panel will be set to latchall alarm inputs in the system. The latching operationwill not allow the loop input devices to generate an

"alarm off" signal that would possibly interrup