All rights reserved 12/16 SSc
1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install the outdoor unit close to the sea shore, contact your local distributor.
Cautions on product corrosion
Warning Ask a qualified installer or contractor to install this product. Do not try to install the product by yourself. Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical shock, fire or explosion.Read the user's manual carefully before using this product. The user's manual provides important safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any enquiries, please contact your local importer, distributor and/or retailer.
Specifications, designs and other content appearing in this brochure are current as of December 2016 but subject to change without notice.
PCSVN1602A
Air Conditioning SystemHeat pump 50Hz
Page 3
Page 7
Page 9
Page 11
Page 13
Page 13
1 2
P r o d u c t L i n e u p
DUCT CONNECTIONMIDDLE STATIC PRESSURE TYPE
CEILING SUSPENDED TYPE
71 100 125 140
RQ71MV1 RQ71MY1FCQ71KAVEA FCQ100KAVEA
RQ125MY1FCQ125KAVEA
RQ140MY1FCQ140KAVEA
FHQ71DAVMA FHQ100DAVMARQ125MY1
FHQ125DAVMARQ140MY1
FHQ140DAVMA
FBQ71EVE FBQ100EVERQ125MY1FBQ125EVE
RQ140MY1FBQ140EVE
FVQ71CVEB FVQ100CVEBRQ125MY1
FVQ125CVEBRQ140MY1
FVQ140CVEB
Outdoor unitIndoor unit
CEILING MOUNTED CASSETTE TYPE
Round Flow
Series
Outdoor unitIndoor unit
Outdoor unitIndoor unit
FLOOR STANDING TYPE
3Phase 50Hz380-415V
Outdoor unit
Outdoor unit
Indoor unit
Heat pump
RQ100MV1 RQ100MY1
RQ71MY1 RQ100MY1
RQ71MV1 RQ71MY1 RQ100MV1 RQ100MY1
RQ71MV1
RQ71MY1 RQ125MY1 RQ140MY1RQ100MY1
RQ71MY1 RQ100MV1 RQ100MY1
CEILING MOUNTED CASSETTE TYPE
CEILING SUSPENDED TYPE
DUCT CONNECTIONMIDDLE STATIC PRESSURE TYPE
FLOOR STANDING TYPE
Daikin meets your needs with the line up of various types of indoor units and power supplies
OUTDOOR UNIT1 Phase 50Hz
220-230V
Outdoor unit RQ71MV1 RQ100MV1
A built-in antibacterial treatment that uses silver ion in the drain pan prevents the growth of slime, bacteria, and mould that cause smells and clogging.
Condensation does not easily form on and dirt does not cling to non-flocking flaps. It is easy to clean.
Non-flocking flapsSilver ion anti-bacterial drain pan
Prevents mould and microorganisms growing out of the dust and moisture that adheres to the filters.
Filter has anti-mould and antibacterial treatment
Comfort enhanced by Round Flow!
Greater comfort
Avoids uneven temperature and discomfort caused by drafts
With uniform temperature distribution
360° air�ow
360° airflow can maintain comfort even if air discharge speed is lower.
Velocity decreases by 25% when set temperature is raised 1℃ to 1.5℃.
Room remains comfortable even when set temperature is raised 1℃.
Enhanced Comfort
Air movement is gentle with Round Flow
Airflow distribution
creates uniform comfort throughout
the space.
• Condition after exposure to the smoke of 600 cigarettes in 1 m3 enclosed space.
Treated surface
Untreated surface
Grimy surface
Resists soiling
External panels are treated with a coating that repels dirt
To prevent dirt sticking to the external panels, they have been coated with a surface treatment
Because air flows out from corner outlets, comfort spreads more widely
Grime prevention and antibacterial coating: Make cleaning easier
Adapts easily to the installation space
Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing material (option) must be used to close each unused outlet.
3-way flow L-shaped 2-way flow
Opposite 2-way flow
(E.g., installed in a corner)
(E.g., installed in a long room)
(E.g., installed near a wall)
(E.g., installed in middle of ceiling)
4-way flow also possible.
All-round flow
Typical flow patterns There are a total of 23 flow patterns.
Operation sound increases when using 2-way or 3-way flow.
Accessory required for indoor unit.Option
CEILING MOUNTED CASSETTE TYPE
FCQ71/100/125/140KA
Round Flow
BRC1E62
Navigation Remote Controller(Wired Remote Controller)
A signal receiver must be added to the indoor unit.
BRC7F634FHeat pump
Wireless remote controller is supplied in a set with a signal receiver.
Wireless LCD remote controller
Signal receiver unit (Installed type)
Note: Remote controller cable is not included and must be procured locally.
Note: Remote controller cable is not included and must be procured locally.
Wired LCD remote controller
BRC1C61
3 4
Cassette air conditioner with 360° uniform airflow sets the standardCassette air conditioner with 360° uniform airflow sets the standard
Easier to maintain
With Ultra long-life filters (option), maintenance is not required in normal shops or offices for up to four years
Options required for specific operating environments
Filter chamber (Can be used with ultra long-life filter)
High-efficiency filter
Filter chamber (Can be used with high-efficiency filter)
Ultra long-life filter
High-efficiency filter unitAvailable in two types: 65% and 90% colorimetry.
Please use if you think the temperature and humidity inside the ceiling exceeds 30°C and RH 80%, respectively.
Insulation kit for high humidity
Using this kit, a duct can be connected to take outdoor air in.There are two chamber types that have intake in two places: with T-duct joint and without T-duct joint.
Fresh air intake kit
Even in dusty environments where the air conditioning is on most of the time, the ultra long-life filter only has to be cleaned once a year.
Ultra long-life filter unit
Panel spacerUse when only minimal space is available between drop ceilings and ceiling slabs.
Sealing material of air discharge outletSealing material block air discharge openings not used in 2-way or 3-way blow.
Outside
Note: Some ceiling constructions may hinder installation. Contact your Daikin Dealer before installing your unit.
40mm
Panel spacer
Branch duct (direct-connection round duct)A round duct can be attached without the need for a chamber.A flanged port for direct connection of a round duct is provided. An existing branch duct chamber can also be fitted (square slit hole).
Dusty area: annual filter change
Ordinary store or office: filter change every 4 years
*For dust concentration of 0.3 mg/m3 (Requires separately sold Air purifier.) 1 year (Approx. 5,000 hr) 15 hr/day x 28 day/month x 12 month/year
*For dust concentration of 0.15 mg/m3
4 years (Approx. 10,000 hr) 8 hr/day x 25 day/month x 12 month/years x 4 years
1 Use of options will increase operating sound.2 Connecting ducts, fan, insect nets, fire dampers, air filters, and other parts
should, as required, be procured locally. 3 When a local-procured fan is used, an interlock with air conditioner is
necessary.Optional PCB(KRP1C63)is required for interlocking.4 It is recommended that the volume of outdoor air introduced through the kit is
limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher quantities will increase the operating sound and may also influence temperature sending.
Note:
The units can be installed in the following different ways.
Intake duct(procured locally)
Direct installation type
Chamber type (with T-duct joint)
KDDP55X160A
KDDP55B160K
Chamber type (without T-duct joint) Note 3.4
Note 3.4
KDDP55B160
Intake duct(procured locally)(duct length: 4 m max.)Connection
chamber
Suction chamber
Connection chamber
Suction chamberTop panel insulation(1)
Top panel insulation(2)Top panel insulation(3)Insulation for decoration panelSide panel insulation Suspension bracket insulation
Flexible duct(procured locally)
T-duct joint(procured locally)
Intake duct(procured locally)(duct length: 4 m max.)
Flexible duct
T-duct joint
Duct flange (with insulation material)
Note 1.2
The condition of the drain pan anddrain water can be checked byremoving the drain plug andsuction grille Drain plug
Just open the
suction grille!
5 6
CEILING MOUNTED CASSETTE TYPE Round Flow
Quick and easy to installJust 256 mm high. Installable in tight ceiling spaces (71KA)
Drain pump is equipped as standard accessory with 850 mm lift
Unified square panels Compact body and quiet operationPanel size is the same for all models, FCQ71-140KA.It is easy to maintain a neat appearance when multiple units are installed in the same room.
Optimal comfort and convenience assured by 2 air discharge modes
Control of airflow rate has been improved from 2-step to 3-step.
dB(A)Sound pressure level
Same for all models
950 mm 950 mm
256 mm *1 266 mm *2
*1 298 mm high with 100–140KA*2 308 mm high with 100–140KA
All models can be installed without using lifter because of the light weight
Transparent drain socket
Each corner of the unit has an Adjuster Pocket that lets you easily adjust the unit's suspended height.
Note: If the wireless remote controller is installed, a signal receiver unit is housed in one of the adjuster pockets.
Since the orientation of the suction grille can be adjusted after installing, the direction of the suction grille lines can be unified when multiple units are installed.
DIII-NET communication standardConnection to a centralised control system is available without option.
Easy height adjustment
Installed in any direction
Switchable fan speed: High/Middle/Low
175 mm
850 mm
4-wayflow
3-wayflow
2-wayflow
4-wayflow
3-wayflow
2-wayflow
3.1 m3.4 m4.0 m
All round flow
2.7 m3.0 m3.5 m
3.0 m3.3 m3.5 m
3.5 m3.8 m-
3.4 m3.9 m4.5 m
All round flow
3.2 m3.6 m4.2 m
3.6 m4.0 m4.2 m
4.2 m4.2 m-
StandardHigh ceiling High ceiling
Criteria for ceiling height and number of air discharge outlets
Note: Factory settings are for standard ceiling height and all-round flow. High ceiling settings (1) and (2) are set with the remote controller by field setting.
(Ceiling height is reference value)
71KA 100–140KA
Ceiling height
Number of air discharge outlets used
Indoor unit
125KA140KA
100KA71KA
High
4444
4335
Middle
3940
37.531.5
Low
3436
3228
Two selectable temperature-sensors See page 19
Note: 1Air direction is set to the standard position when the unit is shipped from the factory. The position can be changed from the remote controller.2Closing of the corner discharge outlets is recommended.
Air direction
Auto air direction control
Settable to 5 different levels between 15° and 60°
Settable to 5 different levels between 25° and 60°
Auto-swing between15° and 60°
Auto-swing between25° and 60°
Recommended for shops with light coloured ceilings that
must be kept spotless.Standard setting to
prevent draft.
Standard setting1 Setting to prevent soiling of ceiling2 (field setting)
At heating startup and thermo OFF, air discharge is automatically set to a near horizontal 25˚ or 30˚ to prevent direct exposure to cool air drafts.
Desired situation
Auto-swing
5-levelsair directionsetting
Draft prevention(In heating mode)
The air direction is set automatically to the memorised position of the previous air direction.
Even in spaces with high ceilings, a comfortable airflow is carried down to the floor level.
Suitable for high ceilings
When all round flow is selected, ceilings up to 4.2 m in height can be accommodated. (100-140KA)
Setting SettingStandard
4.2 m3.6
m3.2m
Oil resistant grille
Note: Intended for use in salons, dining rooms, and ordinary sales floors, this specification is not suitable for kitchens or other harsh environments.
Oil-resistant plastic is used for the air suction grille. This satisfies durability in restaurants and other similar environments.
Comfortable
Flap neatly closes when not in use.
The latest stylish model
Quiet operationdB(A)
Indoor unit HighSound pressure level
Low71DA
100DA125DA140DA
Middle
The technology of the DC fan motor, wide sirocco fan, and large heat exchanger combine for greater airflow and quiet operation
Sophisticated design
White colour
Auto swing (up and down) and louvers (left and right by hand) bring comfort to the room
Switchable fan speed: High/Middle/Low
-
Suitable for high ceilings
StandardHigh ceiling
71DA 100DA 125/140DA2.7m or less 3.8m or less 4.3m or less2.7m~3.5m 3.8m~4.3m
Note: Factory settings is “standard”. “High ceiling” are set with remote controller by field setting.
3.5m
71DA
4.3m
100-140DA
Non-flocking flap
Easy maintenance
Easy-clean, flat surfacesIt is easy to wipe dirt off the flat side and lower surfaces of the unit.
Condensation does not easily form on and dirt does not cling to non-flocking flap. It is easy to clean.
Non-flocking flap
Drain pump kit (option) includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging
Drain pump kit (built inside the unit)
600 mm
Flexible installation
*Water used in the test-run can be drained from the air discharge opening rather than from the side as was formerly the case.
The unit fits more snugly into tight spaces.
Drain pump kit (option) can be easily incorporatedDrain pipe connection can be done inside the unit. Refrigerant and drain pipe outlets are at the same opening.
All wiring and internal servicing can be done from under the unit
Installation flexibility for freedom of design
Easier piping work for rear side by removable frame
DIII-NET communication standardConnection to a centralised control system is available without option.
30 mm or more
30 mm or more
Programme "Dry" See page 19
Two selectable temperature-sensorsSee page 19
Louver manually adjusts for straight or wide angle airflow
38 3442 3444 37
363841
46 3842
Option
BRC1E62Note: Remote controller cable is not
included and must be procured locally.
A signal receiver must be added to the indoor unit. Wireless LCD remote controller
CEILING SUSPENDED TYPE
Wireless remote controller is supplied in a set with a signal receiver.
Signal receiver unit (Installed type)
Comfortable airflow travels throughout the roomComfortable airflow travels throughout the room
FHQ71/100/125/140DA
7 8
Accessory required for indoor unit.Option
Note: Remote controller cable is not included and must be procured locally.
Wired LCD remote controller
BRC1C61
Navigation Remote Controller(Wired Remote Controller)
Heat pump BRC7GA53
(“Auto” is applicable when BRC1E62 is used.)
ComfortSwitchable fan speed:High/Middle/Low and Auto
A built-in antibacterial treatment that uses silver ion in the drain pan prevents the growth of slime, bacteria, and mould that cause smells and clogging.
CleanSilver ion anti-bacterial drain pan
Easy maintenancePosition of drain pan inspection opening has been modified for easier inspection work
High efficiencyDC fan motor and DC drain pump are utilised to improve energy efficiency
Higher lift is realized by utilising built-in DC drain pump with standard accessory
850mm
Middle & High static pressure type(FBQ-D series)
700mm
Using a DC fan motor, the external static pressure can be controlled to within a range of 50 Pa to 150 Pa
Comfort airflow is achieved in accordance with conditions such as duct length.
Adjustable external static pressure
50 Pa 150 PaSet to high static pressure for
advanced needs such as when using dampers and long ducts.
Set to low static pressure when ducts
are short.
Easy maintenance because the drain pan can be removed
Drain pan maintenance check windowThis makes it possible to inspect for drain pan dirt and to confirm drainage during installation without the use of tools.
Inspection opening for drain pan
Drain pan maintenance check window
Airflow rate auto adjustment functionControls the airflow rate using a remote controller during test run.It is automatically adjusted to approximately ±10% of the rated H tap airflow.
DIII-NET communication standardEasier communication and connection with the centralised control system.
Interlock control As an energy saving feature, the room air conditioning unit can be interlocked with the hotel key card system.
Using a 3rd-party building management system, air conditioning and lighting can be interlocked.* Field setting with remote controller
Design and installation flexibility
With a height of only 245 mm, installation is possible even in buildings with narrow ceiling spaces
One of the industry’s most compact bodies in the mid-static pressure range.
245100/125/140E
1,000 1,400800
HeightIndoor unit
WidthDepth
71E(mm)
(mm)
(mm)
245mm
Interlock
Bottom suction is availableWiring and servicing can be done from the underside of the unit (an option part required).
Control box cover
Control box faces outward. Control box faces inward.
Air suction flange
Control box cover
Air suction flange
Bottom plate
Sield plate for side plate(option)
Bottomplate
Switch bottom plate with air suction flange.Make the control box face inward.
Air suction
joistunit
ceiling
Rear suction Bottom suction
BRC1E62
Navigation Remote Controller(Wired Remote Controller)
Note: Remote controller cable is not included and must be procured locally.
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
FBQ71/100/125/140E
A signal receiver must be added to the indoor unit.
BRC4C65Heat pump
Wireless remote controller is supplied in a set with a signal receiver.
Wireless LCD remote controller
Signal receiver unit (Separate type)
Note: Remote controller cable is not included and must be procured locally.
Wired LCD remote controller
BRC1C61
9 10
Thinner design allows greater installation flexibilityThinner design allows greater installation flexibility
Accessory required for indoor unit.Option
Simultaneous air conditioning of two rooms and ventilation grille (ventilation opening)
Ventilation grille
Door-installedventilation grille
Ventilation grille
Wall-installedventilation grille
Under-door cutout
Under-door cutoutWhen air conditioning two rooms simultaneously, the air discharged into each room must be circulated back to the air conditioner. To achieve this, a ventilation duct should be installed for each room or one of the indicated ventilation grilles should be installed on the partitioning wall or under the door between the rooms.
Ventilates air through the partitioning wall. (See right)
Partitioning wall
Note: The under-door cutout method should be used only when there is a small volume of airflow.
Quiet operation
Quick and easy installation and maintenance
Lightweight indoor unitEnables smooth transport and installation of the indoor unit.
The grill will not open even upon impact.
Energy savingDC fan motor improves efficiency
Employs a safety lock function of suction grille
100C 125C 140CHigh
Indoor unitSound pressure level
71C
50 51 5343Middle 47 48 5141Low 44 46 4838
dB(A)
39 47
100C 125C 140C
Weight
Indoor unit 71C(kg)
Comfortable fan speed control
To carry airflow to the far side of the room, airflow rate can be increased 5% or 10% depending on the installation condition or customer's request. (Field setting by remote controller.)
High fan speed mode
Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature.
Programme "Dry"
(applicable for FVQ71/100)
Airflow rate is automatically controlled in accordance with the difference between room temperature and set temperature.
Auto airflow rate is selectable
Example applications
When cooling
Turning louvers and upward and leaving and horizontal will reduce uneven room temperature.
New comfortable airflow control1) Left and right directions
2) Up and down directions Independent up-and-down airflow directions facilitate even room temperature and help save energy.
New unit
(by remote controller)
(by hand)
Freely select both up and down airflow direction with 8-louver (horizontal blade) setting.
Upper louver (1)Upper interlocking louvers (4)Lower interlocking louvers (2)Lower louver (1)
Each set of louvers to can be independently adjusted. (Manual adjustment)
Auto swing direction is selectable from 3 patterns to suit the layout of the room.
Pattern 1 Swing wide across the front
When installed in the center of a wall. When installed in the corner of a room.
Pattern 2 Swing across left side Pattern 3 Swing across right side
Switchable fan speed: High/Middle/Low and Auto("Auto" is applicable when BRC1E62 is used.)
(Applicable when BRC1E62 is used.)
* For dust concentration of 0.15 mg/m3
Long-life filter (standard) requires no maintenance for about 1 year*The filter is washable and reused after 1 year.
-Two time settings (2500 hrs and 1250 hrs) are available to match the installation environment. Maintenance time warning is displayed on the remote controller (filter sign).
-The periodical cleaning time for the filter can be shortened depending on the usage environment.
DIII-NET communication standardConnection to a centralised control system is available without option.
Note: Remote controller cable is not included and must be procured locally.
Wired LCD remote controller
BRC1C61
FLOOR STANDING TYPE
New airflow control for more comfortNew airflow control for more comfort
11 12
Accessory required for indoor unit.Option
BRC1E62 can be
incorporated into the
indoor unit.
(Wired Remote Controller)
Navigation Remote Controller
Note: Remote controller cable is not included and must be procured locally.
BRC1E62
FVQ71/100/125/140C
OUTDOOR UNIT
Outdoor unit
Easy installation and maintenance
Durability
Construction
Non-treated fin
Anti corrosion treated fin
Aluminium
AluminiumCorrosion resistantresin
Hydrophilic treatment
As the bottom frame is subject to corrosion, a corrosion-proof galvarium steel plate is adopted to enhance the durability
Heat exchange fins are provided with anti-corrosion treatment
Allowed refrigerant piping length and level difference
Note : 1Additional refrigerant charging is required if the refrigerant pipe is longer than the length.
Max. length
Max. leveldifference
Pre charged1
RQ71-140M
30 m
50 m(Equivalent length 70m)
30 m
Separation available
If the refrigerant piping length does not exceed 30 m, there is no need for on-site gas charging.
Pre charged for up to 30 metres
Long piping length
The outer panel for the piping connection part of the front, right side and backside can be removed and is easier for post-installation piping work.
4-direction piping offers greate rlayout freedom
Removable part of bottom frame makes the piping work easier
A pump-down switch is provided to make it easier to collect refrigerant if the unit is to be moved or layout modified.
Facilitates pump down (Refrigerant recovery function)
*Pump-down function is available for pre-charged refrigerant amount.
RQ100MV1RQ100MY1
RQ71MV1RQ71MY1
RQ125MY1RQ140MY1
13 14
Whatever your space, give it the comfort it deserves
Easy centralised installation with the module oriented designDepth of 71-140M are standardised as 320 mm. Horizontal continuous mounting is available.
71M
900 mm
320 mm
Suction
Discharge
100M
900 mm
125M
900 mm
140M
900 mm
-20-10
0102030
40
50Wide operation range
46˚CDB
Cooling
-5˚CDB
Outdoor temp(˚CWB)Outdoor temp(˚CDB)
Heating-10˚C
WB
15˚CWB
Cooling is efficient even in winter when indoor temperatures are higher than those outside, such as in underground public spaces or offices with many computers.
Operation range
Suited for year-round cooling applications
Comparison of outdoor unitsRY140LUY1 RQ140MY1
Height 1,345 mm 1170 mmWeight 112 kg 101 kg
Reduced installation work thanks to light, compact outdoor unit.
Compact and lightweight
RQ140MY1RY140LUY1
Reduced by175 mm
Reduced by11 kg
1170mm
Enables temperature sensing closer to target area for improved comfort. (When using remote control from another room, temperature-sensor in indoor unit's air inlet must be selected.)
Facilitates maintenance and repairAll initial settings can be set from the remote controller. After interior construction is complete, ceiling mounted cassette type can be remotely set without having to use stepladder access for manual setting.Setting contents: High ceiling use, air direction, filter type, address for centralised control (group control address is set automatically).
Remote controller is equipped with model name and failure display functions. This facilitates service in the unlikely event of a malfunction.
SkyAir shares common control with Heat Reclaim Ventilator and the other Daikin air-conditioning units, thus simplifying interlocking operations.
Easily adaptable to large-scale, high-function, centralised remote control systems.Installing and connecting control wiring between SkyAir and other Daikin air-conditioning equipment is easy.
LCD panel shows operating status in letters, numbers, and motion.Airflow / swing display Displays auto-swing operating status and setting position of air discharge angle.
Preset temperature / operation mode display Displays preset room temperature and operating status (fan, dry, cool).
Programming time display Operation start and stop time can be set for individual timers up to 72 hours. The LCD also shows when it is time to clean the filter, when changeover is under centralised control, and ventilation/cleaning.
Self-diagnosis function Monitors operating status within the system covering 40 items, and displays a message to indicate as soon as a malfunction occurs.
CEILING MOUNTED CASSETTE TYPECEILING SUSPENDED TYPEDUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
BRC7F634FHeat pump
BRC7GA53BRC4C65
Wired remote controller has built-in temperature-sensor (Applies to wired remote controllers (BRC1C61/1E62))
(Model name display function applies to BRC1E62 only.)
Signal receiver unit (For ceiling mounted cassette type)
Wireless remote controller for each indoor unit type
Wireless LCD remote controller
Note: The signal receiver unit shown in the photograph is for mounting inside the decoration panel of the ceiling mounted cassette type.
Wireless remote controller
BRC7F634F
The wireless remote controller is supplied in a set with a signal receiver.Signal receiver unit is contained inside decoration panel or indoor unit.Shape of signal receiver unit differs according to the indoor unit.
The rubber switch and the oil-resistant plastic casing are adopted for durability.Only 17 mm thick. Can be installed either recessed or exposed.
Easy to read because of large LCD screen.Wired LCD remote controller
BRC1C61
REMOTE CONTROLLER Optional accessory
15 16
Easy-to-read LCD remote controller allows various system control configurations and can control multiple indoor units. Remote controller options are shown on the page introducing each indoor unit model.
Navigation Remote Controller(Wired LCD Remote Controller)
- 5 actions per day can be scheduled for each day of the week.- The holiday function will disable schedule timer for the days that have been set as holiday.- 3 independent schedules can be set. (e.g. summer, winter, mid-season)
Display is available in 11 languages.
ConvenienceWeekly schedule Multilingual display
(English, German, French, Spanish, Italian, Portuguese, Greek, Dutch, Russian, Turkish, and Polish).NEW
Clear DisplayDot matrix display Backlight
displayA combination of fine dots enables various icons.Large text display is easy to see.
This simple, modern designed remote controller with fresh white colour matches your interior design. Operation is much easier and smoother, just follow the indications on the navigation remote controller.
Energy savingNEW
- Sets and saves setting for an increment of time that automatically turns off air conditioner after a preset period of time for each time operation starts.- Period can be preset from 30 to 180 minutes in10-minute increments.
Off timer (programmed)
Setpoint range setNEW Setpoint auto reset
Restaurant exampleRestaurant opened
Temperature is set to 27ºC
27°C
- Saves energy by limiting the min. and max. set temperature.
- Avoids excessive heating or cooling.
- This function is convenient if the remote controller is installed where anyone can change the settings.
- Even if the set temperature is changed, after a preset period new set temperature returns to preset value.
- Period selectable from 30, 60, 90, or 120 min.
Full tables at lunchtimeThen is lowered to 24ºC for crowded room
24°C
After 30 minutes*Automatically returns to preset temperature (27ºC)
*Preset-return time can be set at 30, 60, 90, or 120 min
Returns to
27°Cautomatically
BRC1E62
Central remote controllerEasily adaptable to large-scale, high-function, centralised remote control system.
Centralised control, with a setting as simple as it is with a standardremote controller, of up to 64 groups (1,024 indoor units) is possible.
DCS302CA61 (Option)
With its high functionality, the full colour “all-in-one” graphic controller facilitates management of SkyAir System in a variety of ways.
DCS601C51 (Option)
Unified on/off controller
Centralised control of on/off by group or all at once for up to 256 indoor units.
DCS301BA61 (Option)
Schedule timer
Unified control of weekly schedule for up to 1,024 indoor units.
DST301BA61 (Option)
Schedule timer sets on/off time in 1 minute units to be executed twice a day for a week at a time.
System variation to control multiple indoor units
Control by 1remote controller
Control pattern Wired remote controller Wireless remote controller
Control by 2remote controllers
Group control
Control by external command
Centralised remotecontrol
Interlock controlwith Heat Reclaim
Ventilator
(Basic system)
Link by remote controller group control.
Zone link control by centralised control.
For control from 2 locations such as in room and control room, exits, etc.
For simultaneous control of up to 16 indoor units.
Centralised control of up to 64 indoor groups from remote locationup to 1 km away.
Signal receiver unit installed on indoor unit
Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking. Can also be operated independently by remote controller.
Central remote controller (option)
Heat Reclaim Ventilator
Can be operated simultaneously or independently by remote controller (set by ventilation mode)
Heat Reclaim Ventilator
Non-polar, double-core (max. wiring length 500 m)
Connects 2 wired remote controllers (See note 1)
Automatic address setting function Automatic address setting functionSignal receiver unit installed on 1 indoor unit
Optional wiring adaptor for electrical appendices is necessary
Can be operated simultaneously by remote controller (set by ventilation mode)
Heat Reclaim Ventilator
Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking
Central remote controller (option)
Heat Reclaim Ventilator
Operation and monitoring is carried out using the contact signal from the operation control box in the monitoring room. Optional wiring adaptor for
electrical appendices is necessary
Note:1BRC1E62 can connect to BRC1E62 only. 2It is not possible to use two wireless remote controllers. 3BRC1E62 cannot connect to wireless remote controller.
Central remote controller (option) Central remote controller (option)
Not possible (See note 2, 3)
(Command from outside) (Command from outside)
FunctionsoverviewFunctionsoverview
FUNCTIONS
Work & servicing
REMOTE CONTROLLER Optional accessory
17 18
*1 : Applicable when BRC1E62 is used*2 : Applicable when wired remote controller is used*3 : Applicable when BRC1C61 is used*4: For outdoor units
*5 : Applicable for FVQ71-100*6: Installable on max. 3.5 m(71) and 4.3 m (100-140) high ceiling*7: Option
Note:
RQ71-140MY1 RQ71-140MY1 RQ71-140MY1
Indoor unit
Outdoor unit
Comfort
Cleanliness
Remote Controller
Control features
Options
Others
CEILING SUSPENDED TYPECEILING MOUNTED CASSETTE TYPERound Flow
Auto swing Swing pattern selection
Setpoint auto reset *1Setpoint range set *1Weekly schedule timer *1Off timer (programmed) *1On/Off timer *3
Anti-bacterial air filter
Drain pump mechanism
Pre-charged for up to 30 m *4
Filter signLong-life filter
Ceiling soiling prevention
Auto-restart
Control by 2 remote controllersGroup control by 1 remote controllerExternal command controlCentral remote control Interlock control with Heat Reclaim VentilatorDIII-NET communication standard
High-efficiency filter
Ultra long-life filterFresh air intake kit
Anti corrosion treated heat exchangers *4
Draft prevention function (heating)Independent up-and-down airflow
Auto-cooling/heating change-over
Emergency operationSelf-diagnosis function
RQ71-140MY1RQ71/100MV1 RQ71/100MV1RQ71/100MV1
FLOOR STANDING TYPEDUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
FCQ71-140KAVEA FHQ71-140DAVMA FBQ71-140EVE FVQ71-140CVEB
DC fan mortor (Indoor unit)Switchable fan speed
Programme “Dry”High ceiling applicationTwo selectable temperature-sensors *2
Auto airflow rate *1High fan speed mode
Hot startYear-round cooling applicable
Silver ion anti-bacterial drain pan
Heat pump
3step 3step 3step 3step
*7
*7
*7
*7 *7 *7 *7
*6
*5
Even if there is a malfunction elsewhere in the system, the fan or compressor can still be operated. (depending on the malfunction)
Emergency operation
You can turn up to 16 indoor units on/off with a single remote controller. (When using connected indoor units, the settings must all be the same and on/off will be simultaneous.)
Group control by 1 remote controller
Optional central remote controller enables centralised control of up to 1024 indoor units (64 groups) from up to 1 km away.
Central remote control
The operating parameters of indoor and outdoor units, and sensor data at critical locations throughout the system, are constantly monitored using a microcomputer. To facilitate quick response in the event of a malfunction, a message appears on the LCD of the remote controller and an LED on the unit illuminates.
Self-diagnosis function
Two types are available: 65% and 90% colorimetry.
High-efficiency filterYou can provide air-conditioning with fresh air from outside. Convenient for places where a ventilation fan cannot be installed.
Fresh-air intake kit
Work and Servicing
Control features
Options
Steeper gradient realises more efficient condensate drainage. High-lift is especially useful for long lengths of drain piping.
Maintenance is not required for one year*.The filter is washable and can be reused.
If refrigerant piping length does not exceed 30 m, there is no need for on-site gas charging.
The filter sign warns you when it is time to clean the filter. *When using a wired remote controller the sign is displayed in the LCD. When using a wireless remote controller the filter sign lamp illuminates on the signal receiver unit.
Drain pump mechanism
Long-life filter
Pre charged for up to 30 m
Filter sign
Daikin's innovative air discharge mechanism keeps airflow away from the ceiling. Ceiling cleaning is less frequently required.
Ceiling soiling prevention
Ultra long-life filter
If there is a power outage while the equipment is operating, operations will restart in the same mode as before the power cut when electricity is restored.
Auto-restart
Detects difference in preset temperature and actual room temperature and automatically switches to cooling or heatingaccordingly.
Auto-cooling / heating change-over
Using 2 remote controllers you can operate the equipment locally or from a remote location.Note: When a wireless remote controller is used, remote control by two remote controllers is not possible.
Control by 2 remote controllers
Requires no maintenance for about 4 years* (10,000h) in stores and offices.*For dust concentration of 0.15 mg/m3
Operation and monitoring is carried out using the contact signal from the operation control box in the building monitoring room.
External command control
*An option is required.
Others
Standardly equipped interface enables connection to centralised control system without need of an adaptor.
DIII-NET communication standard
To achieve increased durability by improved resistance to salt corrosion and atmospheric pollution, Anti corrosion treated fin for heat exchangers (with special coating) are used for the heat exchanger of the outdoor unit. In high corrosive areas, regular maintenance needs to be carried out.
Anti corrosion treated heat exchangers
*For dust concentration of 0.15 mg/m3
Enables interlocking control with external equipment such as Heat Reclaim Ventilator.
Interlock control with Heat Reclaim Ventilator
19 20
Abundance of functions that provide comfortable air-conditioning in stores and offices.
Note: Some features only available on selected models. See overview pages for full list of features applicable to each unit.
Note:When units are installed on high ceilings, depending on the model, various restrictions concerning maximum height, air discharge direction, and choice of options may apply.
Delivers air-conditioning comfort all the way down to the floor in air-conditioning zones with high ceilings.
High-ceiling application
High setting provides maximum reach while low setting minimises drafts.
Switchable fan speed
To prevent cold air drafts, automatically adjusts airflow to near horizontal position when heating initially starts or when the thermo off.
Draft prevention function (heating)
Cold air flow is avoided when heating operation starts or whenswitching to heat after defrosting.
Hot start
Airflow rate is automatically controlled in accordance with the difference between room temperature and set temperature.
Auto airflow rate
Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. Useful for reducing uncomfortable humidity without uncomfortable cooling of the room.
Programme "Dry"
Comfort
Delivers comfortable air-conditioning to all areas, near to and far from the air-conditioner.
Auto-swingThe air flow direction can be fixed at your desired angle by the remote controller.
Note: Wireless remote controllers have no temperature-sensor.
Use the temperature-sensor in the indoor unit when controlling air conditioning from another room.
Two selectable temperature-sensorsTemperature-sensors are included in the indoor unit and optional wired remote controller. Temperature sensing closer to target area is possible to further increase the comfort level.
Sets and saves setting for an increment of time that automatically turns off air conditioner after a preset period of time for each time operation starts.
Off timer (programmed)Remote Controller
Operation starts when the preset time of the ON timer elapses and stops when the preset time of the OFF timer elapses.
On/Off timer
Up to five operation ON/OFF settings can be programmed per day for each day of the week. Not only can the time be set for the operation ON setting, but also the temperature.
Weekly schedule timer
Even if the set temperature is changed, after a preset periodnew set temperature returns to preset value.
Setpoint auto reset
Saves energy by limiting the minimum and maximum set temperatures. Avoids excessive heating and cooling.
Setpoint range set
You can increase fan speed approximately 10% higher than the "high" setting.
High fan speed mode
DC fan motor improves efficiency.
DC fan motor (indoor unit)
Independently adjust (manually) the eight horizontal blade louvers in both up and down directions to achieve an airflow that reduces uneven room temperature.
Independent up-and-down airflow
Efficient cooling even in winter when the indoor temperatures are higher than those outside, such as in underground public spaces or offices with many computers.
Year-round cooling applicable
Cleanliness
A built-in antibacterial treatment that uses silver ion in the drain pan prevents the growth of slime, bacteria, and mould that cause smells and clogging.
Silver ion anti-bacterial drain panThe air filter has an anti-bacterial treatment to help prevent the growth of bacteria and mould on it.
Anti-bacterial air filter
FUNCTIONS
(1) standard setting (2) Ceiling soiling prevention setting
You can freely set air discharge settings by remote controller.
Swing pattern selection
21 22
SPECIFICATIONS
CEILING MOUNTED CASSETTE TYPE
Cooling capacity1,3
Rated (Min. - Max.) kW
V1Y1
Btu/h
°CDB°CWB
Certified Operation range
Sound pressure level4
°CWBCertified Operation range
Motor outputCompressorCoil
ModelName
Indoor unit
Outdoor unit
Dimensions(HXWXD)Machine weight
Colour
mmmm
dB(A)
kWRefrigerant charge (R-410A) kg
dB(A)Dimensions (HXWXD) mm
Unit
Piping connections
mmLiquid (Flare)mmGas (Flare)mmDrain Indoor unit
Outdoor unit
Decoration panel
UnitDecoration panel
kgkg
UnitDecoration panel
Machine weight kg
Machine weight kg
Machine weight kg
Airflow rate (H/M/L) m3/mincfm
Outdoorunit
Colour
mm
Heat insulation
Max. interunit piping length mmMax. installation level difference
Power supply
Type
Cooling / Heating
Sound pressure level4 (H/M/L)
Indoorunit
Hermetically sealed scroll typeType Cross fin coil
43/37.5/32
32/26/20
298X840X84050X950X950
5.52421
2.2 3.0
84(V1), 83(Y1) 103(V1), 101(Y1)
3.75 2.9
108 101
----------
1 Phase, 220–230 V, 50 Hz3 Phase, 380-415 V, 50 Hz
30
Ivory white
Fresh white
Both liquid and gas piping
50 (Equivalent length 70)
VP25 (I.D 25XO.D 32)
1,130/918/706
-5 to 46-10 to 15
12 to 25°CDB 15 to 27
kWPower consumption Cooling1
44/39/34 44/40/36
33/28/22.51,165/988/794
Cooling Heating
Cooling Heating
7.1
35/31.5/28
50/52 53/56 54/56770X900X320 1,170X900X320
256X840X840
2.7(Charged for 30 m)
3.7(Charged for 30 m)
21/17.5/13.5741/618/477
Heating capacity2,3
Rated (Min. - Max.) kW
Btu/h8.0
2.72Heating2
CoolingHeating
2.85
W/WCOP 2.612.81
3.833.752.612.99
4.665.062.682.77
4.914.972.853.22
24,20010.0
34,10012.5
42,70014.0
47,800
27,300 11.2
38,200 14.0
47,800 16.0
54,600
Outdoor unit
Hermetically sealed scroll type
42/38/34235X1,590X690235X1,270X690
3832
28/24/2020.5/17/14988/847/706
38/36/34724/600/494
CEILING SUSPENDED TYPE
Ivory white
°CWB
kWBtu/h
kWPower consumption
°CDBCertified Operation range
Certified Operation range
Motor output
Cooling / Heating
CompressorCoil
Dimensions (HXWXD)
Colour
mmdB(A)
kWRefrigerant charge (R-410A) kg
dB(A)Sound pressure level4Dimensions (HXWXD) mm
Piping connections
mmLiquid (Flare)mmGas (Flare)mmDrain Indoor unit
Outdoor unit
Airflow rate (H/M/L) m3/min
Outdoorunit
Colour
mm
Heat insulation
Max. interunit piping length mmMax. installation level difference
TypeCross fin coilType
Sound pressure level4 (H/M/L)
Indoorunit
Cooling capacity1,3
Rated (Min. - Max.)
cfm44/41/37
31/27/231,094/953/812
Light ivory
°CWB
12 to 25°CDB 15 to 27
W/WCOP
46/42/38
34/29/241,200/1,024/847
Cooling1
kWBtu/h
Heating capacity2,3
Rated (Min. - Max.)
kWHeating2
CoolingHeating
CoolingHeating
CoolingHeating
1 Phase, 220–240 V, 50 Hz
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
Indoor unit
kWBtu/h
°CDB
°CWB
Cooling / Heating
Certified Operation range
Certified Operation range
Motor outputCompressorCoil
Indoorunit
Dimensions (HXWXD)Air filter6
Colour
mm
dB(A)
kWRefrigerant charge (R-410A)
Sound pressure level5
Sound pressure level5 (H/M/L)
dB(A)Dimensions (HXWXD) mm
Piping connections
mmLiquid (Flare)mmGas (Flare)mmDrain Indoor unit
kg
Airflow rate (H/M/L)Fan
Outdoorunit
Colour
Heat insulation
Max. interunit piping length mmMax. installation level difference
Type
----------
mmOutdoor unit
Ivory white
kWCooling1Power consumption
Pacfm
External static pressure4
Cooling capacity1,3
Rated (Min. - Max.)
°CWB
12 to 25°CDB 15 to 27
m3/min
245X1,000X800----------
37
Hermetically sealed scroll typeType Cross fin coil
7.1
2.2
2.71
Rated 50 (50-150)1,130/953/794
32/27/22.5812/688/56523/19.5/16
38/35.5/3338/35/33
3.0
245X1,400X80047
3.75 2.9
1,271/1,077/88336/30.5/25
40/37.5/35
kWBtu/h
Heating capacity2,3
Rated (Min. - Max.) 8.0
Heating2
CoolingHeating
CoolingHeating
CoolingHeating
2.49
W/WCOP 2.623.21
FLOOR STANDING TYPE
°CWB°CDBCooling
HeatingCertifiedOperation range
Sound pressure level4
°CWBCoolingHeating
CertifiedOperation range °CDB
Motor outputCompressor
Dimensions (HXWXD)
Colour
mmdB(A)
kWRefrigerant charge (R-410A) kg
dB(A)Dimensions (HXWXD) mm
Piping connections
mmLiquid (Flare)mmGas (Flare)mmDrain Indoor unit
Outdoor unit
Outdoorunit
Colour
mm
Heat insulation
Max. interunit piping length mmMax. installation level difference
TypeType
Cooling / Heating
Sound pressure level (H/M/L)4
Indoorunit
391,850X600X270
635/565/494
47
988/883/777
1,850X600X350
Ivory white Coil Cross fin coil
15 to 2712 to 25
988/918/847 1,059/988/91818/16/14 28/25/22 28/26/24 30/28/26
Fresh white
Hermetically sealed scroll type
Fan Airflow rate (H/M/L) m3/mincfm
43/41/38 50/47/44 51/48/46 53/51/48
24,200
27,300
10.0
3.78
11.2
3.912.652.86
34,100
38,200
12.5
4.67
14.0
4.522.683.10
42,700
47,800
14.0
5.02
16.0
4.912.793.26
47,800
54,600
Note : 1Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, 15°CWB; outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 3Capacities are net, including a deduction for cooling for indoor fan motor heat. 4The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection.
Note : 1Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
2Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, 15°CWB; outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 3Capacities are net, including a deduction for cooling for indoor fan motor heat. 4External static pressure is changeable in 11 stages by remote controller. 5The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection. 6Air filter is not standard accessory, but please mount it in the duct system of the suction side. Select its dust collection efficiency(gravity method) 50% or more.
Note : 1Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 3Capacities are net, including a deduction for cooling for indoor fan motor heat.4The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection.
Note : 1Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, 15°CWB; outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 3Capacities are net, including a deduction for cooling for indoor fan motor heat. 4The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection.
Machine weight kg
Machine weight kg
Machine weight kg
Machine weight kg
9.515.9
26.0 (Hole)
2.2 3.0
83 101
3.75 2.9
108 101
30Both liquid and gas piping
50 (Equivalent length 70)
VP20 (I.D 20XO.D 26)
-5 to 46-10 to 15
50/52 53/56 54/56770X900X320 1,170X900X320
2.7(Charged for 30 m)
3.7(Charged for 30 m)
9.515.9
26.0 (Hole)
71FCQ71KAVEA
RQ71MV1
100FCQ100KAVEA
RQ100MV1
RQ71MY1 RQ100MY1
125FCQ125KAVEA
RQ125MY1
140FCQ140KAVEA
RQ140MY1
V1Y1
ModelName
Indoor unit
Outdoor unit
Power supply1 Phase, 220–230 V, 50 Hz
3 Phase, 380-415 V, 50 HzOutdoor unit
71FBQ71EVE
RQ71MV1
100FBQ100EVE
RQ100MV1
RQ71MY1 RQ100MY1
125FBQ125EVE
RQ125MY1
140FBQ140EVE
RQ140MY1
ModelName
Indoor unit
Outdoor unitPower supply 3 Phase, 380-415 V, 50 HzOutdoor unit
71FHQ71DAVMA
100FHQ100DAVMA
RQ71MY1 RQ100MY1
125FHQ125DAVMA
RQ125MY1
140FHQ140DAVMA
RQ140MY1
V1Y1
ModelName
Indoor unit
Outdoor unit
Power supply 1 Phase, 220–230 V, 50 Hz3 Phase, 380-415 V, 50 Hz
Outdoor unit
71FVQ71CVEB
RQ71MV1
100FVQ100CVEB
RQ100MV1
RQ71MY1 RQ100MY1
125FVQ125CVEB
RQ125MY1
140FVQ140CVEB
RQ140MY1
84(V1), 83(Y1) 103(V1), 101(Y1) 108 101
30Both liquid and gas piping
50 (Equivalent length 70)
VP25 (I.D 25XO.D 32)
-5 to 46-10 to 15
50/52 53/56 54/56770X900X320 1,170X900X320
9.515.9
26.0 (Hole)
2.2 3.0
84(V1), 83(Y1) 103(V1), 101(Y1)
3.75 2.9
108 101
30Both liquid and gas piping
50 (Equivalent length 70)
VP20 (I.D 20XO.D 26)
-5 to 46-10 to 15
50/52 53/56 54/56770X900X320 1,170X900X320
2.7(Charged for 30 m)
3.7(Charged for 30 m)
9.515.9
26.0 (Hole)
7.1
8.0
2.702.852.632.81
3.754.132.672.71
4.515.002.772.80
4.874.942.873.24
24,20010.0
34,10012.5
42,70014.0
47,800
27,300 11.2
38,200 14.0
47,800 16.0
54,600kW
Btu/h
kWPower consumption
Cooling capacity1,3
Rated (Min. - Max.)
W/WCOP
Cooling1
kWBtu/h
Heating capacity2,3
Rated (Min. - Max.)
kWHeating2
CoolingHeating
7.1
8.0
2.873.042.472.63
3.953.752.532.99
4.794.672.573.00
5.445.282.573.03
24,20010.0
34,10012.3
42,00014.0
47,800
27,300 11.2
38,200 14.0
47,800 16.0
54,600
2.7(Charged for 30 m)
3.7(Charged for 30 m)
--------------------
----------
intelligent Touch Controller2
Kit nameName of option
DCS302CA61DCS301BA61DST301BA61
Remark
Replacement long-life filter
L-type piping kit (for upward direction)Remote controller
Resin net
Wireless type
Central remote controller2
Unified ON/OFF controller2
Schedule timer2
Wiring adaptor for electrical appendicesWiring adaptor for electrical appendices3
Installation box for adaptor PCB
CEILING SUSPENDED TYPE
Note: 1Wiring for wired remote controller to be procured locally.2The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.3Installation box for adaptor PCB(KRP1D93A) is necessary.
FHQ71DAVMA FHQ100DAVMA FHQ125DAVMA FHQ140DAVMA
KRP1BA54DCS601C51
KRP4AA52
KAFP501A80 KAFP501A160
KJB311AAKJB212AA
Remote sensor (for indoor temperature)Electrical box with earth terminal (3 blocks)Electrical box with earth terminal (2 blocks)
BRC1C61BRC1E62Navigation Remote Controller Wired type1
Wired type1
Drain pump kitFresh air intake kit
KDU50P140VEKDDQ50A140
Heat pump BRC7GA53
KRP1D93A
KHFP5N160
KRCS01-4B
Indoor unit
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
FLOOR STANDING TYPEKit nameName of option FVQ71CVEB FVQ100CVEB
DCS302CA61DCS301BA61DST301BA61
KAFJ95L160
Remark
Replacement long-life filterBRC1C61Remote controller
Navigation Remote ControllerCentral remote controller2
Unified ON/OFF controller2
Schedule timer2
intelligent Touch Controller2
Adaptor for wiring3
Wiring adaptor for electrical appendicesInstallation box for adaptor PCB
Note: 1Wiring for wired remote controller to be procured locally. 2The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.3Installation box for adaptor PCB (KRP4AA95) is necessary.
FVQ125CVEB FVQ140CVEB
KRP1BA57DCS601C51
KRP4AA52KRP4AA95
BRC1E62Wired type1Wired type1
Only one mounting plate can be installed for each indoor unit.Mounting plate is necessary for each adaptor marked .
FBQ71EVE FBQ100EVE FBQ125EVE FBQ140EVEName of option Remark
High-efficiency filter1
Filter chamber(for rear suction)1
Long-life filter1
Air discharge adaptor
Adaptor for wiring Wiring adaptor for electrical appendices(2)Remote sensorMounting plate for adaptor PCB.3,4,5
Central remote controller6
Unified ON/OFF controller6
Schedule timer6
intelligent Touch Controller6
Service panel
Remote controller
65%90%
WhiteFresh whiteBrown
Wired type2
Wired type2
Wireless type
Kit name
KAFP632B80
Shield plate for side plate
Navigation Remote Controller
KAFP632B160KAFP633B80 KAFP633B160KDDFP63B80 KDDFP63B160KAFP631B80 KAFP631B160KTBJ25K80W KTBJ25K160WKTBJ25K80F KTBJ25K160FKTBJ25K80T KTBJ25K160TKDAP25A71A
KDBD63A160Heat pump BRC4C65
BRC1C61BRC1E62
KRCS01-4BKRP4A98
DCS302CA61DCS301BA61DST301BA61DCS601C51
KDAP25A140A
Note: 1If installing high efficiency filter and long-life filter to the unit, filter chamber is required.
3
4Up to 2 adaptors can be fixed for each mounting plate.2Wiring for wired remote controller to be procured locally. 5
6The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
KRP1C64KRP4AA51
Outdoor unitKit name
RQ71MV1 RQ100MV1RQ71MY1 RQ100MY1 RQ125MY1 RQ140MY1
Heat pump
Central drain plug
Name of option
KKPJ5F180
23 24
OPTIONS
Indoor unit
intelligent Touch Controller5
Note: 1Refer to page 6 for the details.2Please order using the names of both components instead of set name. 3Required for installing high-efficiency filter unit and ultra long-life filter unit. 4Wiring for wired remote controller to be procured locally.5The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 6Installation box for adaptor PCB (KRP1H98A) is necessary.
CEILING MOUNTED CASSETTE TYPEKit name
KDJP55B160KDJP55B80
KAFP556C80KAFP557C80KAFP552B80KAFP553B80
KAFP556C160KAFP557C160KAFP552B160KAFP553B160
FCQ71KAVEA FCQ100KAVEA FCQ125KAVEA FCQ140KAVEAName of option Remark
Chamber type
Decoration panel
Fresh air intake kit1
Central remote controller5
Unified ON/OFF controller5
Schedule timer5
Adaptor for wiring6
Without T-duct jointWith T-duct joint
Direct installation type
Sealing material of air discharge outletPanel spacer
Wiring adaptor for electrical appendices(2)6
Installation box for adaptor PCB
High-efficiency filter unit (including filter chamber)
(Colorimetric method 65%)(Colorimetric method 90%)
Replacement high-efficiency filter
(Colorimetric method 65%)(Colorimetric method 90%)
Remote controller Wireless type
Wired type4 Wired type4
Branch duct chamber
Remote sensor (for indoor temperature)
DCS601C51
DCS302CA61DCS301BA61DST301BA61
KRP1C63
KDBH55K160FKDBP55H160FA
KDDP55B160 (Components:KDDP55C160-1, KDDP55B160-2)2
KDDP55B160K (Components:KDDP55C160-1, KDDP55B160K2)2
KDDP55X160A
KRP4AA53
Heat pump BRC7F634F
BYCP125K-W1
KRP1H98AKRCS01-4B
BRC1E62BRC1C61
KDDFP55C160Filter chamber
Navigation Remote Controller
KDTP55K160Chamber connection kit3Insulation kit for high humidity
KKSJ55KA160KDTP55K80
For each flow pattern – all round, 4-way, 3-way, 2-way, branch duct connection – the compatibility of each independently installed option (shown in the column on the left) to accessory options (listed across the top of each table) is shown in the cells where the relevant row and column intersect.A circle (o) indicates compatibility, and a cross (x) indicates incompatibility. Any options not shown below are not suitable for independent or accessory installation.
Round flow type: List of optional parts required to achieve different flow patterns
1In some cases, depending on how the unit is embedded in the ceiling, use of branch ducts and fresh air intake kits may not be possible. Before starting installation work make sure to check whether or not joint installation is possible. In particular, ensure that the lower fixing position caused by the addition of panel spacers is acceptable.
2Use a chamber connection kit if two different types of optional chamber are used together. In this case, the fresh air intake kit must be installed in the upper position.3It is not possible to use panel spacers in a 2-way flow installation. 4It is not possible to install a branch duct on the same side to which a fresh air intake kit (direct mount) is installed.
Panel/grille relatedIndependently installable optional parts
Operation control relatedAuxillary function related
Filter related
Optional accessory parts
Independently installable optional partsOptional accessory parts
Independently installable optional partsOptional accessory parts
Panel spacer1
Panel spacer1 o o ox oWireless remote controller o o oo o
Fresh air intake kit (Direct installation type) o o oo ox o o
xx
High-efficiency filter unit2
Filter related Ultra-long-life filter unit2
o o ox
xUltra-long-life filter unit2 o o o xx
Insulation kit for high humidity
Panel/grille relatedOperation control relatedAuxillary function related
Panel spacer1
Wireless remote controller
Fresh air intake kit (Direct installation type)Insulation kit for high humidity
All round flow 4-way flow
o3 o3 xx o3
o3 o
x
xxo o
o3 o xx
o ox o o x
o3 o o xx
3-way flow 2-way flow
1-way branch / unit 3-way flowBranch duct chamber 1(Round duct type)
o o o4 xx o2-way branch / unit 2-way flow1-way branch / unit 2-way flow
x o o4 xx ox o o4 xx o
Branch duct connection
Wireless remote controller
Fresh air intake kit(Direct installation type)
High-efficiency filter unit2
Insulation kit for high humidity
Ultra-long-life filter unit2
Panel spacer1 Wireless remote controller
Fresh air intake kit(Direct installation type)
High-efficiency filter unit2
Insulation kit for high humidity
Ultra-long-life filter unit2
Panel spacer1 Wireless remote controller
Fresh air intake kit(Direct installation type)
Fresh air intake kit (Chamber type)1,2 o o ox o
Fresh air intake kit (Chamber type)1,2 o3 o xx o
oo
xoo
o3
o
x
x
x
o
o o o
Fresh air intake kit (Chamber type)1,2
Fresh air intake kit (Chamber type)1,2
Fresh air intake kit (Chamber type)1,2
High-efficiencyfilter unit2
Insulation kit for high humidity
Ultra-long-life filter unit2
KAFP551K160KAFP55C160
KAFP55H160H
Replacement long-life filterUltra long-life filter unit (including filter chamber)Replacement ultra long-life filter
CEILING MOUNTED CASSETTE TYPE
Notes:1Sticking location for manufacture's label manufacture's label for indoor unit: Suction grille inner side's electric components box's lid surface manufacture's label for decoration panel : Decoration panel's corner decoration cover inner surface2In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail.
3When the temperature and humidity in the ceiling exceed 30˚C and RH 80% or the fresh air is inducted into the ceiling or the unit continues 24 hour operation, an additional insulation (thickness 10mm or more of glasswool or polyethylene form) is required.
4Though the installation is acceptable up to maximum of 910mm square ceiling opening, keep the clearance of 35mm or less between the indoor unit and the ceiling opening so that
the panel overlap allowance can be ensured.5Please do not place the thing been damp and troubled under an indoor unit. When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
950
950
arrow viewA
Piping ConnectionSide
Drain ConnectionSide
Note 28
6
7
860~910(Ceiling opening space) (Note 4)710(Hanging bolt pitch)
420
420
780(
Hang
ing
bolt
pitc
h)86
0~91
0(Ceili
ng op
ening
space
) (Note
4)
300or less
9
B
C
(round shape type)
840340
80 80124
55 55
256
124
110
95
40
29
850
175
Adjus
table(
0~67
5)
10246
160
50
165
125
Connection positionof branch duct(square-shaped type)
4 1 2
2 100=200
16-M4 Prepared hole
Connection positionof branch duct
Hanging bolt4-M8~M10
C/L20157
350280330 15
00 or
more
(requ
ired s
pace
)Fro
m the flo
or side
2500 or
more
Connection positionof branch duct(square-shaped type)
Connection positionof branch duct(round shape type)
27-M4 Prepared hole
35 or less(Note 4)
35 or less (Note 4)
A
For h
eight
instal
lation
81
124
2x100=200
157
124
105
64
55840
110
350
160
13095
50
256
58555
604215
0
3
Connection positionof branch duct(round shape type)
Connection positionof branch duct(square-shaped type)
16-M4 Hole
arrow viewB
95
85
350
C/L124
81
110
160
2x100=200
124
157
[FCQ71KAVEA]
20-M4Prepared hole
Connection positionof branch duct(square-shaped type)
Connection positionof branch duct(round shape type)Connection positionof fresh air intake kit(direct installation type)
ø100(knock hole)
arrow viewC
2x100=
200
160
C/L 350
124
95109
80
90
183
25
90
157
80213
124
[FCQ71KAVEA]
C/L
160167679529
93
90196
8080
16025
90213
157
350
20-M4Prepared hole
Connection positionof branch duct(square-shaped type)
Connection positionof branch duct(round shape type)Connection positionof fresh air intake kit(direct installation type)
ø100(knock hole)
arrow viewC
2 10
0=20
0
[FCQ100-140KAVEA]
1500
or m
ore(re
quire
d spa
ce)
From th
e floor s
ide 250
0 or mo
reFo
r heig
ht ins
tallat
ion
5064 160
256157350
1309560105
150
42
9367
2916
0
167
840 555581 85
Connection positionof branch duct(square-shaped type)
Connection positionof branch duct(round shape type)
27-M4 Prepared hole
35 or less35 or less (Note 4)(Note 4)
3
5
A
2 100=200
[FCQ71KAVEA] [FCQ71KAVEA]
[FCQ100-140KAVEA]
[FCQ71-140KAVEA] [FCQ71-140KAVEA]
[FCQ100-140KAVEA]
2 100=200
160
C/L160
157350
81 85
67
167
9529
93
Connection positionof branch duct(round shape type)
Connection positionof branch duct(square-shaped type)
16-M4 Hole
arrow viewB
[FCQ100-140KAVEA]
Adjus
table(
0~67
5)
Connection positionof branch duct(square-shaped type)
16-M4 Prepared hole
(round shape type)
Connection positionof branch duct
Hanging bolt4-M8~M10 1
160850
280
80
10
330
340
50
55
4
55
40
80
12529
95
157
298
167
160
350
175
16528
8
20
2 100=200
2
840
160
C/LThe necessary space is 500mm or more when the air-outlet is blocked with the accessory.Moreover when the corner areas are blocked (both right and left of the blocked air outlet), the necessary space is 200mm or more.
1500mm or more200mm or more
1500mm or more
1500mm or more1500mm
or more200mmor more
Required space
Liquid pipe connectionGas pipe connectionDrain pipe connectionTransmission wiring connectionRemote controller wiring connectionAir-outletSuction grilleCorner decoration coverDrain hose (accessory)
12345
6789
DIMENSIONS (Unit: mm)
57
131
φ45
19791
6
4 5 11
14
197
5
57
690
(Req
uire
d sp
ace)
For h
eight
instal
lation
From t
he floo
r side
2500 o
r more
Floor side
(Req
uired
spac
e)
Obstacle
300 o
r mor
e
131270
235
30 or more(Service space)
30 or more(Service space)
4-M8~M10Hanging bolt
1
268
156
83
214
221
76
268
105
(Note.2)Brand name plate
The Front
(For left pipe)Drain piping connection VP20 6
45723
57
1230
87
195
35
102
(Han
ging
bo
lt pi
tch)
210
116
(Hanging bolt pitch)
210
131
105
30
100
156
260
189
163
8
18
10
17 1620
5
220103
175
Position : Hole of wall for taking out in pipe back(View from the front)
(Req
uire
d sp
ace)
19 15
120
90
51
92 63
606340
134 59
157
115
90
175
Position slit hole for taking out in pipe back(View from the front)
Connection position of fresh air intake kitφ100(Knock out hole)
12
9
Notes:1
2
3
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail.Please do not place the thing been damp and troubled under an indoor unit.When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
CEILING SUSPENDED TYPE
[FHQ71DAVMA]
1234567891011121314151617181920
Air discharge grilleAir suction grilleAir filterGas pipe connectionLiquid pipe connection Drain pipe connectionEarth terminal (inside the control box) (M4)HangerRear pipe penetration coverTop panel penetration coverRight side pipe connection Left back drain pipe connection Left side drain pipe connection Right side drain pipe connection Hole of wall for taking out in pipe back Upward drain pipe connection Upward gas pipe connection Upward liquid pipe connection Power supply wiring and a unit wiring back connectionPower supply wiring and a unit wiring upper connection
131
57
197
φ45
91
6
4 5 11
1457
519
7
690
Floor side
(Req
uired
spac
e)
Obstacle
300 o
r mor
e
For h
eight
instal
lation
From t
he floo
r side
2500 o
r more
(Req
uire
d sp
ace)
13
235
159030 or more(Service space)
30 or more(Service space)
4-M8~M10Hanging bolt
1
156
83
268
221
10576
268
214
The Front
(Note.2)Brand name plate
(For left pipe)Drain piping connection VP20
6
45723
189
57102
35
210
156
131
30 87
260
210
105
19516
3
116
100
1550(Hanging bolt pitch)
(Han
ging
bo
lt pi
tch)
8
18
10
17 1620
103220
517
5(R
equi
red
spac
e)
Position : Hole of wall for taking out in pipe back(View from the front)
19 15
15790
60
175
59
92
12090
6313451
40
115
63
Connection position of fresh air intake kitφ100(Knock out hole)
Position slit hole for taking out in pipe back(View from the front)
12
9
Notes:1
2
3
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail.Please do not place the thing been damp and troubled under an indoor unit.When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
[FHQ100-140DAVMA]
1234567891011121314151617181920
Air discharge grilleAir suction grilleAir filterGas pipe connectionLiquid pipe connection Drain pipe connectionEarth terminal (inside the control box) (M4)HangerRear pipe penetration coverTop panel penetration coverRight side pipe connection Left back drain pipe connection Left side drain pipe connection Right side drain pipe connection Hole of wall for taking out in pipe back Upward drain pipe connection Upward gas pipe connection Upward liquid pipe connection Power supply wiring and a unit wiring back connectionPower supply wiring and a unit wiring upper connection
CEILING SUSPENDED TYPE
25 26
27 28
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
Notes:1Locations of Manufacturer's Label:Surface of a control box2Make sure to mount the air filter inside the air passage on the suction side. (Select Duct Collection Efficiency <Gravimetric Method>50% or more.)3If the temperature and humidity in the ceiling is likely to exceed 30℃ and RH80%, strengthen heat insulation by applying the additional insulation materials such as glass wool or polyethylene that has thickness of 10mm or more.4Do not put things that should not get wet under the indoor unit. Dews may drop when humidity reaches over 80%, a drain gets stuck or air filters are not clean.5Space for Service Works
1)Inspection hatch 1and 2(450x450) (Fig.A-1) and a space of 300mm or more under the unit. (Fig.A) Note:Inspection hatch 2 is not needed when there is a space for service work under the unit.2)Inspection hatch 1(450x450) on the control box side, and Inspection hatch 2 under the unit. (View B-1)3)Inspection hatch 3 under the unit and control box. (View B-2)
Provide service spaces for service work such as check and maintenance of the control box and drain pump by one of the following ways.
Provide enough space for maintenance and mount the drainpan and control box.Check the drawing of optional accessories when mounting optional accessories such as filter chamber and humidifier.
Liquid pipe connection1Gas pipe connection2Drain pipe connection3Earth terminal(terminal in Control box)4Control box(Inside)5
Remote control wiring connection6Power supply wiring connection7Air discharge flange8Air suction flange9Hanger10
Socket(For maintenance)11Drain hose(Accessory)12Drain hose connection(Accessory)13
[FBQ71EVE]
2500
or m
ore
5x156=780
176
194
815
100
792
1000
500
207
Airoutlet
12
4
2
69
226
6x150=900
977
6020
8
952
36-φ4.7hole
1
200 o
r less
Inspection hatch 2450 or more
11
※When can work enters the space under the unit, inspection hatch 2 is unnecessary.
18-8x12 oblong hole
(A c
ase
with
out
the
ceilin
g)
630
7
10
450
or m
ore
Air inlet(Note.2)
245
134
( )Drain pan removaland part exchange.
850
or le
ss
(Hanging bolt position)
499
Ceiling
450
1038
(Han
ging
bol
t pos
ition
)
Floor surface
(Not
e.5)
38
(All around)
Drain pan maintenancecheck hole
(From the Air inlet)
(643
or l
ess)
(Service space)
(All around)13
8
Inspection hatch 1450 or more
123
CeilingInspection hatch
300
or m
ore
Fig.A
Control boxCASE1)
6
65
800 or more
16-8x12 oblonghole
13x6
5=84
5 1000
or m
ore
3x50
=150
(All around) Inspection hatch 1(450x450)
835
800 or more
Control box
(All around)
9
(Ser
vice
spa
ce)
136
26
(SAME AS THE INDOORUNIT SIZE +300 OR MORE)
200
or le
ss
Control Boxmaintenance space
300
800 or more
50
Adju
stab
le
13
1300
or m
ore
8
View B-1
Airoutlet
300
or m
ore
30-φ4.7hole
183
5
179
(SAME AS THE INDOORUNIT SIZE OR MORE)
300 or less
Control box
53
222
Drain panmaintenance space
91
Inspection hatch 3
800
3
11x6
5=71
5
View B-2
2x50
=100
Inspection hatch 2
(From the Air outlet)
View
Air inlet
Air outlet
Inspection hatch 2※(450X450)
200
or le
ss
Control box
Inspection hatch1(450x450)
Unit base
Fig. A-1Suspention bolt(4pieces)
Air inlet
500Inspection hatch
CeilingB
CASE 2),3) Control box
20 or
more
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
Liquid pipe connection1Gas pipe connection2Drain pipe connection3Earth terminal(terminal in Control box)4Control box(Inside)5
Remote control wiring connection6Power supply wiring connection7Air discharge flange8Air suction flange9Hanger10
Socket(For maintenance)11Drain hose(Accessory)12Drain hose connection(Accessory)13
[FBQ100-140EVE]
2500
or m
ore
1400
500
207
Airoutlet
69
50-φ4.7hole
200 o
r less
※When can work enters the space under the unit, inspection hatch 2 is unnecessary.
26-8x12 oblong hole
(A c
ase
with
out
the
ceilin
g)
630
450
or m
ore
Air inlet(Note.2)24
5
134
Inspection hatch 2450 or more
( )Drain pan removaland part exchange.
850 o
r less
(Hanging bolt position)
Ceiling
650
1438
(Han
ging
bol
t pos
ition
)
Floor surface
(Not
e.5)
38
(All around)
Drain pan maintenancecheck hole (From the Air inlet)
(643 o
r less
)
(Service space)
(All around)
Inspection hatch 1450 or more
65
20-8x12 oblonghole
20x6
5=13
003x
50=1
50
(All around)
800 or more
(All around)
(Ser
vice
spa
ce)
136
26Control Boxmaintenance space
30050
Adju
stab
le
Airoutlet
300
or m
ore
44-φ4.7hole
183
179
300 or less
53
Drain panmaintenance space
91
800
2x50
=100
(From the Air outlet)View
Air inlet
Air outlet
Inspection hatch 2※(450X450)
200
or le
ss
CeilingInspection hatch
300 o
r more
Fig.A
Control boxCASE1)
800 or moreControl box
Inspection hatch 1(450x450)
Control box
Inspection hatch1(450x450)
Unit base
Fig. A-1
(SAME AS THE INDOORUNIT SIZE +300 OR MORE)
bolt Suspention(4pieces)
200
or le
ss
Air inlet
500
1700
or m
ore
Control box
Inspection hatch 3
View B-2
1400
or m
ore
800 or moreView B-1
(SAME AS THE INDOORUNIT SIZE OR MORE)
Inspection hatch 2
18x6
5=11
70
7x156=10921192
100100
1
8
52699
176
60
9
1215
13524 7 100
1377
6x150=900
138
12
226
13
222
100
6
208
1235
10
3
11
194
100
123
Inspection hatchCeiling
B
CASE 2),3) Control box
20 or
more
DIMENSIONS (Unit: mm)
Notes:1Locations of Manufacturer's Label:Surface of a control box2Make sure to mount the air filter inside the air passage on the suction side. (Select Duct Collection Efficiency <Gravimetric Method>50% or more.)3If the temperature and humidity in the ceiling is likely to exceed 30℃ and RH80%, strengthen heat insulation by applying the additional insulation materials such as glass wool or polyethylene that has thickness of 10mm or more.4Do not put things that should not get wet under the indoor unit. Dews may drop when humidity reaches over 80%, a drain gets stuck or air filters are not clean.5Space for Service Works
1)Inspection hatch 1and 2(450x450) (Fig.A-1) and a space of 300mm or more under the unit. (Fig.A) Note:Inspection hatch 2 is not needed when there is a space for service work under the unit.2)Inspection hatch 1(450x450) on the control box side, and Inspection hatch 2 under the unit. (View B-1)3)Inspection hatch 3 under the unit and control box. (View B-2)
Provide service spaces for service work such as check and maintenance of the control box and drain pump by one of the following ways.
Provide enough space for maintenance and mount the drainpan and control box.Check the drawing of optional accessories when mounting optional accessories such as filter chamber and humidifier.
This model to be fixed with fixture as shown below.
In case of fixing it at the bottomIn case vibration resistance is required, fix it at both the bottom and the rear.
50 or more
1500 or more
50 or more
Required space
AB
100
C
50
Detail
0.7
Suction grille stopper
(Two both sides)
18
2-7X15 oblong hole
184 184
(For wood screw)
(Accessory)
330 30
Fixture
95
6
66E
G
68
Full open position of suction grille
H
Pull out direction of air-filter
F
D
75
KJ
L
740
or m
ore
(Pull
out d
imen
sion o
f air-
filter
)
5010
0
Approx.46
2
1
3
5
4
200
34 223
825
600
1850
314
253
95
598
677
616
541
8
9
10
130 215 126
PN
260
M
130
View
7
4- 14 Hole(For bolt)
FLOOR STANDING TYPE
Notes: 1Sticking location for manufacturer’s label: on the surface of cover of switch box inside the suction grille. 130
A
FVQ100/125/140CVEB50
190
B110
266
C186
350
D270
44
E45
49
F50
130
G50
190
H110
260
J180
266
K186
322
L242
79
M57
202
N144
229
P149FVQ71CVEB
Suction grilleAir filterThrough hole for side piping(70x90 oblong slit hole)Through hole for side piping( 80 slit hole)Through hole for side piping( 27 slit hole)Through hole for rear piping/wiring(80x130 oblong slit hole)Through hole for bottom piping/wiring(126x130 square hole)Liquid pipe connectionGas pipe connectionDrain pipe connection
123
4
5
6
7
8910
[FVQ71-140CVEB]
OUTDOOR UNIT // RQ71MV1/MY1
OUTDOOR UNIT // RQ100MV1/MY1
102
60
52
6
191
7
5
95
422
55423
19
16
570
80
142
117
145
84
24
45
8
5495
7
55
1170
95
Hole for anchor bolt4-M12
350
38
36
30
1989
89140140 620
900
56 320
3030
(345
~355
)
71
223
67
16
3
54
6
4
89
2
5
53
17
65
13
58
376
Gas pipe connectionLiquid pipe connectionService port Grounding terminalRefrigerant piping intakePower supply wiring intakeControl wiring intakeDrain pipe connection
12345678
Gas pipe connectionLiquid pipe connectionService port Grounding terminalRefrigerant piping intakePower supply wiring intakeControl wiring intakeDrain pipe connection
12345678
29 30
DIMENSIONS (Unit: mm)
140 620
102
89
6
5
3
5
4
54
320
900
52
16
84
24
142
7
376
5
6716
38
117
89
7
569560
54
140
1
19145
19
13
350
770
339
289
9595 223
191
6
30
70
30
8
58
8055
5345
71
36 3034
1
55
Hole for anchor bolt4-M12
(345
~355
)
OUTDOOR UNIT // RQ125/140MY1
12345678
Gas pipe connectionLiquid pipe connectionService port Grounding terminalRefrigerant piping intakePower supply wiring intakeControl wiring intakeDrain pipe connection
320
5
7
1170
24
422
145
8 71
Hole for anchor bolt4-M12
45
19
84
102
6
89
900
6
36
9595
60
350
13
58
140
55
54
4
423
5
89
1638
67
55
(345
~355
)
80
89
30
95
5319 52
142
191
70
376
30
7
5
2
7
54
3140
117
16
56
30
223
1
5
620
6
31 32
REMOTE CONTROLLER
Wired type
Staple
Remote controller
17
17
0~5
117
Remote controller
Remote controller
(Between remote controller and control box)
17
• Installation methodA Exposed body, exposed cord C Exposed body, embedded codeB Exposed body, embedded cord
Conduit
Control box
Through hole
Size
Specifications of cord
0.75~1.25 mm2
Total length 500 m
Type Shield wire (insulated thickness: 1 mm or more)Note) 1. Remote controller cord and staple are not
attached. They are field supplied parts.
120
120
17 18
42
84
38
Cord outlet hole2823
46
• Remote controller dimensions
Wireless typeCEILING MOUNTED CASSETTE TYPE <Round Flow>• Remote controller dimensions
• Remote controller holderinstallation procedure<installation to wall surface>
• Receiver installation procedure
• Receiver detail
Transmitting part
157
62 17.5
Liquid crystalremote controller(wireless)
Remote controllerholder
DUCT CONNECTION MIDDLE STATIC PRESSURE TYPE
120
72 83.5
106
(Ceil
ing o
penin
g)
70 180.5
35 49
Service space for ceiling installation
• Receiver detail
Note :
Mor
e th
an 9
0(S
revi
ce s
pace
)
(Ceiling opening)
2-5x9 Slot
Switch box(field Supplied parts)
Do not install more than 3 receivers in the vicinity of one another.With 4 or more units, there is always the possibility of malfunction
( 12- 16)
Receiver
Drain pipingside
Refrigerantpiping side
Decoration panel
BRC1C61
19
Upper case Lower case
40
2346
2848.5
4284
5X7 oblong hole
Code outlet hole5X15 oblong hole
Lower case portion
Lower case portion
Staple
19
A Exposed cord C Embedded cord(use switch box)
B Embedded cord
84
46Switch box for two switchex.) KJB211A(optional accessory)
Condit
19
0~5
Switch box [field supplied part]
(Between remotecontroller and control box)
48.5
19
Note)2Through hole
40
( 8- 10)
84
28
Switch box for one switchex.) KJB111A(optional accessory)
• Installation method
2.If the hole size is too large or the location is not proper, the hole may come out from the remote controller.
Note) 1. Remote controller cord and staple are not attached. They are field
supplied parts.
Size
Specifications of cord
0.75~1.25 mm2
Total length 500 m
Type Vinyl cord with sheath or cable (insulated thickness: 1mm or more)
BRC1E62
(Green)120
120
Operationlamp
Top left outlet
Left outlet
Top centeroutlet
CEILING SUSPENDED TYPE
• Receiver installation procedure
Receiver
• Receiver detail
The Front
DIMENSIONS (Unit: mm)
1000
or more
300(200)
or more
L H
L H
H
L
500
or more
100(50)
or more
L H
For RQ71/100MV1, RQ71-140MY1
300(200)
or more
1000 or more
200 or more
100
or more
100 or more 100 or more
100(50)
or more
500 or more
When there are obstructions on the inlet side and both lateral sides
2. For series installation (more than two units)When there are obstructions on both sides
1. For single unit installation When there is an obstruction only on the inlet side
1. For single unit installation When there is an obstruction on the inlet side
2) When there is an obstruction in the overhead space
When there are obstructions on both sides
When there are obstructions on the inlet side and both lateral sides
2. For series installation (more than two units)
1. For single unit installation
2. For series installation (more than two units)
1. For single unit installation
2. For series installation (more than two units)
1. For single unit installation
2. For series installation (more than two units)
100
or more
500 or less
1000
or m
ore
An obstruction in the overhead space
500 or less
500 or more
1000
or m
ore
An obstruction in the overhead space
500 or less
1000 or more
1000
or m
ore
An obstruction in the overhead space
150
or more
150 or more 150 or more
500 or less
1000
or m
oreAn obstruction
in the overhead space
300(200)
or more
1000 or more
200 or more
500 or less
1000
or m
ore
An obstruction in the overhead space
1000 or more
1) When the overhead space is open
2) When there is an obstruction in the overhead space
1) When the overhead space is open
When there is an obstruction on the inlet side1 When there is an obstruction on the outlet side2
1) When the overhead space is open (There is no limit to the height of the obstruction on the outlet side.)
When there are obstructions on both the inlet and outlet sides(When the obstruction on the outlet side is higher than the unit itself)
3
Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book.
Installation service space for outdoor unit
The values in ( ) are for RQ71 type. (Unit: mm)
33 34
MEMO