Diaphragm Pumps PD02P-XXS-XTX Size 02 ¼” inlet, ⅜” outlet Air motor P Polypropylene A 1x inlet / 1x outlet D 1x inlet / 2x outlet E 2x inlet / 1x outlet H 2x inlet / 2x outlet Wet end D Groundable Acetal K Kynar PVDF P Polypropylene Hardware S Stainless steel Valve / diaphragms TA Teflon / Santoprene TG Teflon / Nitrile TT Teflon / Teflon Seats D Acetal K Kynar PVDF P Polypropylene Max. 17.4 litres per minute (3.83 gallons/min) @ 6.9 bar (0.053 l/cycle). Suspended solids max. diameter: clean fluids only. ¼” / ⅜” NPT (or ½” / ½” NPT) fluid in / outlet. ¼” NPT air inlet. Best selling models: PD02P-APS-PTA, PD02P-APS-PTT, PD02P-ADS-DTT Pump weight Groundable Acetal 2.10 kg (4.08 lbs) Kynar PVDF 2.22 kg (4.90 lbs) Polypropylene 1.85 kg (4.64 lbs) Temperature limits Groundable Acetal -12-82°C (10-180°F) Kynar PVDF -12-93°C (10-200°F) Polypropylene +2-66°C (35-150°F) Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet) P.025-XXXXX / XXX / XX / XXX Max. 18.1 litres per minute (3.98 gallons/min) @ 4.8 bar (0.020 l/cycle). Suspended solids max. diameter: 0.4 millimetres (0.016 inches). ¼” / ¼” thread fluid in / outlet. ⅛” air inlet. Pump weight Kynar PVDF 1.40 kg (3.00 lbs) Polypropylene 1.40 kg (3.00 lbs) Stainless Steel 4.00 kg (8.81 lbs) Aluminium 2.00 kg (4.40 lbs) Temperature limits Kynar PVDF -12-107°C (10-225°F) Polypropylene ±0-79°C (32-175°F) Air inlet pressure 8.6 bar (125 psi) Air outlet pressure 8.6 bar (125 psi) Suction lift 9.45 metres (31 feet) Wetted parts / outer piston plates KK Kynar / Kynar KZ Kynar / No piston plates PP Polypropylene / Polypropylene PZ Polypropylene / No plates SZ Stainless AZ Aluminium Centre section LL Acetal PP Polypropylene Air valve L Acetal P Polypropylene Diaphragms BNS Buna-N TNL PTFE / Neoprene backup WFS Wil-flex (Santoprene) Valve balls TF PTFE Valve seat K Kynar P Polypropylene Valve seat “O” ring BN Buna-N TV PTFE WF Wil-flex Best selling models: P.025-PPPPP/WFS/TF/PWF, P.025-PZPPP/TNL/TF/PTV ARO & Wilden Product Specifications Size - 1/4” in/outlet XP025 - Pro-Flo XP025 - ATEX Rated get the best quality brands at the most cost effective prices - and ship t hem straight on to you! So from a small polypropylene water pump to a 23:1 ratio, high pressure ram, we endeavour to bespoke systems give us the knowledge and experience to find the right solution for you… Ingersoll Rand, Wilden and Fluidair ; our extensive range of pumps, packages and With over 25 years experience, full workshop facilities and authorised distributor status for operated double diaphragm pumps, piston pumps and spares. Air Pumping Engineering Services specialise in the source, supply and servicing of air For pump dimensions, service kits and common accessories, see pages 6 to 10 BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Transcript
Diaphragm Pumps
PD02P-XXS-XTX
Size 02 ¼” inlet, ⅜” outlet
Air motor P Polypropylene
A 1x inlet / 1x outlet D 1x inlet / 2x outlet E 2x inlet / 1x outlet H 2x inlet / 2x outlet
Wet end D Groundable Acetal K Kynar PVDF P Polypropylene
get the best quality brands at the most cost effective prices - and ship them straight on to you! So from a small polypropylene water pump to a 23:1 ratio, high pressure ram, we endeavour to
bespoke systems give us the knowledge and experience to find the right solution for you… Ingersoll Rand, Wilden and Fluidair; our extensive range of pumps, packages and With over 25 years experience, full workshop facilities and authorised distributor status for
operated double diaphragm pumps, piston pumps and spares. Air Pumping Engineering Services specialise in the source, supply and servicing of air
For pump dimensions, service kits and common accessories, see pages 6 to 10BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Air Operated Diaphragm Pumps
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
PD05X-XXS-XXX-B
Size 05 ½” in/outlet
Air motor A Aluminium R Polypropylene
Inlet / outlet A NPT B BSP
Wet end A Aluminium S Stainless steel
Hardware S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel GG Nitrile ST St. steel / Teflon TT Teflon UU Polyurethane Seats D Acetal K Kynar PVDF P Polypropylene
Max. 45 litres per minute (9.89 gallons/min) @ 6.9 bar (0.15 l/cycle). Suspended solids max. diameter: 2.4 mm (0.094 inches). ½” / ½” fluid in / outlet. ¼” NPT air inlet. Best selling models: PD05R-BAP-AAA-B, PD05R-BAP-FTT-B, PD05R-BSS-STT-B
Pump weight Aluminium 3.70 kg (8.15 lbs) Stainless steel 6.50 kg (14.33 lbs)
Add 1 kg (2.2 lbs) for aluminium air valve
Temperature limits Aluminium -12-82°C (10-180°F) Stainless steel -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
PD05P-XXS-XXX-B
Size 05 ½” in/outlet
Air motor P Polypropylene
Inlet / outlet A NPT B BSP
Wet end D / E Groundable Acetal K / L Kynar PVDF P / R Polypropylene (E, L & R: multiple ported)
Hardware S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel ST St. steel / Teflon TT Teflon VV Viton Seats D Acetal K Kynar PVDF P Polypropylene S Stainless steel
Max. 54 litres per minute (11.88 gallons/min) @ 6.9 bar (0.15 l/cycle). Suspended solids max. diameter: 2.4 mm (0.094 inches). ½” / ½” fluid in / outlet. ¼” NPT air inlet.
Best selling models: PD05P-BPS-PAA, PD05P-BPS-PTT, PDO5P-BDS-DTT, PD05P-BKS-KTT
Pump weight Groundable Acetal 2.90 kg (6.39 lbs) Kynar PVDF 3.10 kg (6.83 lbs) Polypropylene 2.40 kg (5.29 lbs)
3 For pump dimensions, service kits and common accessories, see pages 6 to 10
Air Operated Diaphragm Pumps
P2(00)-XXXXX / XXX / XX / XXX
Best selling models: P1-AAPPP/BNS/BN/ABN, P1-SSPPP/TNU/TF/STV, P1-PPPPP/TNU/TF/KTV, P1-KKPPP/TNU/TF/KTV
Pump weight Aluminium 11.0 kg (24.3 lbs) Ductile Iron 21.0 kg (46.3 lbs) Kynar PVDF 10.0 kg (22.0 lbs) Polypropylene 8.0 kg (17.6 lbs) Stainless steel 23.0 kg (50.7 lbs)
Temperature limits Aluminium -40-176°C (-40-350°F) Ductile iron -40-176°C (-40-350°F) Kynar PVDF -12-93°C (10-200°F) Polypropylene +2-66°C (35-150°F) Stainless steel -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 9.8 metres (32 feet)
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Max. 170 litres per minute (45 gallons/min) @ 6.9 bar (0.34 l/cycle). Suspended solids max. diameter: 3.18 millimetres (0.125 inches). 1” / 1” thread fluid in / outlet. ¼” air inlet.
PD10P-XXS-XXX
Size 10 1” in/outlet
Air motor P Polypropylene E Conductive PP
Inlet / outlet A NPT B BSP F Flanged (side) Y Flanged (end)
Wet end K Kynar PVDF P Polypropylene E Conductive PP
Hardware S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel GG Nitrile ST St. steel / Teflon TT Teflon VV Viton
Valve Seats H Hard steel 440 K Kynar PVDF P Polypropylene S Stainless steel
Max. 200 litres per minute (44 gallons/min) @ 6.9 bar (0.99 l/cycle). Suspended solids max. diameter: 3.2 mm (0.125 inches). 1” / 1” thread or ANSI DIN flanged fluid in / outlet. ¼” NPT air inlet.
Best selling models: PD10P-FPS-PAA, PD10P-FPS-PTT, PD10P-FKS-KTT
Pump weight Kynar PVDF 12.5 kg (27.5 lbs) Polypropylene 9.0 kg (19.8 lbs) Conductive Polypropylene 9.0 kg (19.8 lbs)
Air motor A Aluminium R Polypropylene S Stainless Steel
Inlet / outlet A NPT B BSP
Wet end A Aluminium C Cast iron H Hastelloy S Stainless steel
Hardware P Plated steel S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel GG Nitrile ST St. steel / Teflon TT Teflon VV Viton
Valve seats A Santoprene G Nitrile C Hytrel H Hard st. steel E Carbon steel L Hastelloy F Aluminium S Stainless steel
Max. 198 litres per minute (43.5 gallons/min) @ 6.9 bar (0.94 l/cycle). Suspended solids max. diameter: 3.2 mm (0.125 inches). 1” / 1” fluid in / outlet. ¼” NPT air inlet. Best selling models: PD10A-BAP-AAA, PD10A-BAP-FTT, PD10A-BSS-STT
Pump weight Aluminium 8.3 kg (18.3 lbs) Cast iron 16.0 kg (35.2 lbs) Hastelloy 18.0 kg (39.7 lbs) Stainless steel 17.3 kg (38.1 lbs) Less 2.75 kg (6.0 lbs) for polypropylene air valve Add 5.8 kg (12.8 lbs) for stainless steel air valve
Temperature limits PD10X-XXX-XVV -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Size 15 1½” in/outlet
Size 15 1½” in/outlet
P4(00)-XXXXX / XXX / XX / XXX
Best selling models: P4-AAAPP/BNS/BN/BN, P4-SSAPP/TNU/TF/STF, P4-PPAPP/TNU/TF/PTV, P4-KKAPP/TNU/TF/KTV
Pump weight Aluminium 13.0 kg (24.3 lbs) Ductile Iron 22.0 kg (46.3 lbs) Kynar PVDF 10.0 kg (22.0 lbs) Polypropylene 8.0 kg (17.6 lbs) Stainless steel 20.0 kg (50.7 lbs)
Temperature limits Aluminium -40-176°C (-40-350°F) Ductile iron -40-176°C (-40-350°F) Kynar PVDF -12-93°C (10-200°F) Polypropylene +2-66°C (35-150°F) Stainless steel -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 9.8 metres (32 feet)
Max. 212 litres per minute (46.6 gallons/min) @ 6.9 bar (0.30 l/cycle). Suspended solids max. diameter: 6.4 millimetres (0.250 inches). 1½” / 1½” thread fluid in / outlet. ¼” air inlet.
Size - 1½” in/outlet, non-metallic P4 - Pro-Flo
Wetted parts / outer piston plates AA Aluminium / Aluminium SS Stainless steel / St. steel WM Ductile iron / Mild steel WW Ductile iron / Ductile iron Size - 1½” in/outlet, metallic
XXP4 - Pro-Flo XPV4 - Pro-Flo V XPX4 - Pro-Flo X XPX4 - ATEX Rated
Wetted parts / outer piston plates KK Kynar PP Polypropylene / Polypropylene TT Teflon
Air chambers / centre section A Aluminium S Stainless st. C PTFE coated V Halar coated L Acetal
Centre section / Air valve LL Acetal PP Polypropylene
Diaphragms BNS Buna-N (Nitrile) BNU Buna Ultra-Flex EPS EPDM EPU EPDM Ultra-Flex FSS Saniflex (Hytrel) NES Neoprene NEU Neoprene Ultra-Flex PUS Polyurethane TEU PTFE / EPDM backup TSU PTFE / Saniflex VTS Viton VTU Viton Ultra-Flex WFS Wilflex (Santoprene)
Valve ball BN Buna-N EP EPDM FS Saniflex FV Sanitary Viton NE Neoprene PU Polyurethane TF PTFE VT Viton WF Wilflex
Valve seat K Kynar P Polypropylene T PTFE PFA
Valve seat “O” ring BN Kynar PU Polyurethane TV PTFE
Air chambers / centre section A Aluminium N Nickel-plated C PTFE coated S Stainless st. L Acetal V Halar coated
Centre section / Air valve AA Aluminium NN Nickel-plated CC PTFE coated PP Polypropylene LL Acetal SS Stainless steel
Diaphragms BNS Buna-N (Nitrile) BNU Buna Ultra-Flex EPS EPDM EPU EPDM Ultra-Flex FSS Saniflex (Hytrel) NES Neoprene NEU Neoprene Ultra-Flex PUS Polyurethane TEU PTFE / EPDM backup TNU PTFE / neoprene TSU PTFE / Saniflex VTS Viton VTU Viton Ultra-Flex WFS Wilflex (Santoprene) XBS Conductive buna-N
Valve ball BN Buna-N EP EPDM FS Saniflex NE Neoprene PU Polyurethane TF PTFE VT Viton WF Wilflex
Valve seat A Aluminium BN Buna-N EP EPDM FS Saniflex H Alloy C M Mild steel NE Neoprene PU Polyurethane S Stainless steel VT PTFE PFA WF Wilflex
For pump dimensions, service kits and common accessories, see pages 6 to 105
Air Operated Diaphragm Pumps
P8(00)-XXXXX / XXX / XX / XXX
Best selling models: P8-AAAPP/BNS/BN/BN, P8-SSAPP/TNU/TF/STF, P8-PKAPP/TNU/TF/PTV, P8-KKAPP/TNU/TF/KTV
Pump weight Aluminium 32.0 kg (70.5 lbs) Cast iron 47 kg (103.6 lbs) Kynar PVDF 43.0 kg (94.8 lbs) Polypropylene 34.0 kg (75.0 lbs) Stainless steel 51.0 kg (112.4 lbs)
Temperature limits Aluminium -40-176°C (-40-350°F) Cast iron -40-176°C (-40-350°F) Kynar PVDF -12-93°C (10-200°F) Polypropylene +2-66°C (35-150°F) Stainless steel -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 9.8 metres (32 feet)
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
PD20X-XXX-XXX-B Size 20 2” in/outlet
Inlet / outlet A 2” NPT B 2” BSP F 2” ANSI/DIN
Wet end A Aluminium C Cast iron H Hastelloy S Stainless steel
Hardware P Plated steel S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel GG / JG Nitrile ST St. steel / Teflon TT Teflon VV / LV Viton
Valve seats G Nitrile A Santoprene H Hard st. steel C Hytrel K Kynar E Carbon steel L Hastelloy F Aluminium S Stainless steel
Max. 644 litres per minute (141.6 gallons/min) @ 8.3 bar (5.3 l/cycle). Suspended solids max. diameter: 6.4 mm (0.252 inches). 2” / 2” fluid in / outlet. ¾” NPT air inlet.
Best selling models: PD20A-BAP-AAA-B, PD20A-BCP-GGG-B PD20A-BAP-KTT-B, PD20A-BSS-STT-B
Pump weight Aluminium 41.5 kg (91.5 lbs) Cast iron 66.9 kg (147.5 lbs) Hastelloy 70.3 kg (155.0 lbs) Stainless steel 68.0 kg (150.0 lbs)
Add 13.1 kg (28.8 lbs) for Cast iron or Stainless steel air valve
Temperature limits PD10X-XXX-XVV -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Max. 591 litres per minute (130.0 gallons/min) @ 6.9 bar (2.95 l/cycle). Suspended solids max. diameter: 6.4 millimetres (0.252 inches). 2” / 2” thread fluid in / outlet. ½” air inlet.
PD20P-FXS-XXX
Size 20 2” in/outlet
Air motor P Polypropylene E Conductive PP
Inlet / outlet F ANSI/DIN Flange
Wet end K Kynar PVDF P Polypropylene E Conductive PP
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Wetted parts / outer piston plates KK Kynar / Kynar PK Polypropylene / Kynar
Size - 2” in/outlet, non-metallic XXP8 - Pro-Flo
Air chambers A Aluminium C PTFE coated aluminium S Stainless steel V Halar coated aluminium
Centre section / Air valve PP Polypropylene
Diaphragms BNS Buna-N (Nitrile) BNU Buna-N Ultra-Flex EPS EPDM EPU EPDM Ultra-Flex FSS Saniflex (Hytrel) NES Neoprene NEU Neoprene Ultra-Flex PUS Polyurethane TEU Teflon / EPDM TNU Teflon / Neoprene VTS Viton VTU Viton Ultra-Flex WFS Wilflex (Santoprene)
Valve ball BN Buna-N EP EPDM NE Neoprene PU Polyurethane TF Teflon VT Viton WF Wilflex
Valve seat K Kynar P Polypropylene
Valve seat “O” ring BN Buna-N PU Polyurethane TV Teflon WF Wilflex
Centre section / Air valve AA Aluminium CC PTFE coated aluminium NN Nickel-plated aluminium PP Polypropylene SS Stainless steel Air chambers A Aluminium C PTFE coated aluminium N Nickel-plated aluminium S Stainless steel V Halar coated aluminium Wetted parts / outer piston plates AA Aluminium / Aluminium SS Stainless steel / Stainless st. WW Ductile iron / Ductile iron
Valve ball BN Buna-N EP EPDM FS Saniflex NE Neoprene PU Polyurethane TF Teflon VT Viton WF Wilflex
Valve seat A Aluminium BN Buna-N FG Saniflex H Alloy C M Mild steel ND Nordel NE Neoprene PU Polyurethane S Stainless steel VT Viton WF Wilflex
For pump dimensions, service kits and common accessories, see pages 6 to 106
Air Operated Diaphragm Pumps
Best selling models: P15-AAAPP/BNS/BN/BN, P15-SSAPP/TNU/TF/STF, P15-PKAPP/TNU/TF/PTV, P15-KKAPP/TNU/TF/KTV
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Max. 920 litres per minute (202.4 gallons/min) @ 6.9 bar (5.72 l/cycle). Suspended solids max. diameter: 9.5 millimetres (0.374 inches). 3” / 3” thread fluid in / outlet. ¾” air inlet.
P15(00)-XXXXX / XXX / XX / XXX
Wetted parts / outer piston plates AA Aluminium / Aluminium HH Alloy C / Alloy C SS Stainless steel / Stainless st. WW Ductile iron / Ductile iron Air chambers A Aluminium C PTFE coated aluminium N Nickel-plated aluminium S Stainless steel Centre section A Aluminium C PTFE coated aluminium N Nickel-plated aluminium S Stainless steel Air valve A Aluminium C PTFE coated aluminium N Nickel-plated aluminium P Polypropylene S Stainless steel
Valve ball BN Buna-N EP EPDM FS Saniflex NE Neoprene PU Polyurethane TF Teflon VT Viton WF Wilflex
Valve seat A Aluminium BN Buna-N EP EPDM FS Saniflex H Alloy C M Mild steel NE Neoprene PU Polyurethane S Stainless steel VT Viton WF Wilflex
Valve seat “O” ring FS Flouro-seal TF Teflon
Pump weight Alloy C 112.0 kg (246.9 lbs) Aluminium 60.0 kg (132.3 lbs) Ductile iron 98.0 kg (216.0 lbs) Stainless steel 90.0 kg (198.4 lbs)
Temperature limits P15-XXXXX-XXX-XX-XXX -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 9.8 metres (32 feet)
PD30X-XXX-XXX-C
Size 20 3” in/outlet
Inlet / outlet A 3” NPT B 3” BSP
Wet end A Aluminium C Cast iron H Hastelloy S Stainless steel
Hardware P Plated steel S Stainless steel
Balls / diaphragms AA Santoprene CC Hytrel GG Nitrile ST Stainless steel TT Teflon VV Viton
Valve seats G Nitrile A Santoprene H Hard st. steel C Hytrel K Kynar E Carbon steel L Hastelloy F Aluminium S Stainless steel
Max. 1041 litres per minute (229.0 gallons/min) @ 8.3 bar (10.6 l/cycle). Suspended solids max. diameter: 9.5 mm (0.374 inches). 3” / 3” fluid in / outlet. ¾” NPT air inlet.
Best selling models: PD30A-BAP-AAA-B, PD30A-BCP-GGG-B PD30A-BAP-KTT-B, PD30A-BSS-STT-B
Pump weight Aluminium 58.8 kg (129.6 lbs) Cast iron 98.2 kg (216.5 lbs) Hastelloy 113.3 kg (249.8 lbs) Stainless steel 103.8 kg (228.8 lbs) Add 18.2 kg (40.1 lbs) for Stainless steel air valve
Temperature limits PD30X-XXX-XVV-C -40-176°C (-40-350°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Size - 3” in/outlet, metallic XXP15 - Pro-Flo XPV15 - Pro-Flo V XPX15 - Pro-Flo X XPX15 - ATEX Rated
Teflon, Viton, Nordel and Hytrel are registered trademarks of DuPont Dow Elastomers. Santoprene is a registered trademark of Monsanto Co., licensed to Advanced Elastomer Systems, L.P. Kynar is a registered trademark of Penwalt Corp. Halar is a registered trademark of Solvay. Hastelloy is a registered trademark of Haynes International, Inc.
PF20X-FXS-XXX
Size 20 2” in/outlet
Inlet / outlet A 2” NPT B 2” BSP F 2” ANSI/DIN Flange
Wet end A Aluminium C Cast iron S Stainless steel
Hardware P Plated steel S Stainless steel
Balls / diaphragms AA Santoprene GG Nitrile UA Polyurethane /
Santoprene VT Viton / Teflon
Valve seats S Stainless steel
Max. 644 litres per minute (141.6 gallons/min) @ 8.3 bar (5.3 l/cycle). Suspended solids max. diameter: 50.0 mm (1.968 inches). 2” / 2” fluid in / outlet. ¾” NPT air inlet.
Best selling models: PF20A-BAP-SAA, PF20A-BAP-SGG, PF20A-BCP-SAA
Pump weight Aluminium 44.2 kg (97.4 lbs) Cast iron 75.4 kg (166.2 lbs) Stainless steel (NPT/BSP) 75.3 kg (166.0 lbs) Stainless steel (Flanged) 75.3 kg (166.0 lbs) Add 13.1 kg (28.8 lbs) for Stainless steel air valve
Temperature limits PF20X-XXX-XVT 4-107°C (40-220°F)
Air inlet pressure 6.9 bar (100 psi) Air outlet pressure 6.9 bar (100 psi) Suction lift 6 metres (20 feet)
Air motor A Aluminium C Cast iron S Stainless Steel
Air motor A Aluminium R Polypropylene S Stainless Steel
¹ At 4.5 bar / 60 cycles per minute. ² With standard muffler. ³ With optional continuous duty muffler, p/n: 67263 (metallic), 67323 (plastic).
Ingersoll Rand Drum Pump Set For fast and convenient drum-decanting duties. Pump assembly mounts directly to drum for clean and easy fluid transfers. Supplied with 2” bung adaptor to fit most drum sizes, and availability of many different constructions ensure maximum product compatibility! Basic Pump: Pump, bung adapter, air safety shut-off, siphon Tube, weather seal & base Complete / Transfer: Basic pump plus fluid hose (optional non-drip nozzle) Complete / Dispense: Basic pump plus foot valve and non-drip nozzle
ARO Pulsation Dampeners Effectively reduces material pressure variations, surges and shock to piping and delivery during pump reversal. Available for 1:1 ratio 1”, 2” and 3” diaphragm pumps, with multiple material build options to ensure best product compatibility. Ideal for low pressure spray applications.
2” 3”
ARO STOP model no.:
For diaphragm pump
For motor (piston pump)
635040 ½”, 1” 3”
23644-400 1½”, 2” 4¼”, 6”
635043 3” 8”, 10”, 12”
ARO Stop Valves for Overrun control
DA005-XXX-X-X
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Basic Drum Pump Packages
Water/Oil DA005-PPUU-2-A
Water/Oil DA005-PPNN-2-A
Mild Acid DA005-PPTT-2-A
Solvent DA005-SSTT-2-A
Solvent DA005-ASTT-A-A
Water/Oil DA005-PPUU-2-C
Water/Oil DA005-PPNN-2-N
Oil DA005-PPNN-B-M
Oil DA005-APNN-2-O
Complete Drum Pump Packages
Oil DA005-APNN-B-P
Oil DA005-APNN-2-A
50/50 Dosing Kits Use one pump to transfer two fluids, or produce a 50% / 50% mix. Kits include manifolds and seals to retrofit to standard pump.
Sound Shield The Wilden Sound Shield is an enclosure designed to reduce mechanical and pneumatic sound emissions of air operated diaphragm pumps. Utilising a closed-cell polyethylene foam construction, the unit offers a basic splash guard between product and personnel, UV-ray protection and good chemical and absorption resistance.
Wilden SD Equalizer® The Equalizer range is designed to remove pressure variations from the discharge of the pump. Manufactured with existing Wilden diaphragm pump parts, the flow-through design automatically sets and maintains the correct air pressure as required. With material options to compliment the full Wilden pump range, and sizes from ½” to 3”
Wilden Electric Flow Monitor Accessories Wil-Gard II detects diaphragm failure at the source: the primary diaphragm. Sensors located between the primary and backup diaphragms trigger an audible and/or visual alarm on fluid contact, alerting you of any leaks sooner! Flow Control System II (FCSII) is a state-of-the-art microprocessor controlled batching computer designed to control the operation of Wilden’s Accu-Flo pumps, for specific, accurate and reliable batching. Pump Cycle Monitor (PCMI) counts pump cycles by sensing the movement of the air valve piston (Turbo-Flo) or air valve spool (Pro-Flo). The unit is ideal for batching and cycle based duties, and can be used remotely.
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
Wilden Drum Pump Kit The standard features of the Wilden air-operated pump allow it to excel in drum pump applications. With variable speed and pressure capabilities, the ability to run dry, self-prime and dead-head, the kit offers complete flexibility at low costs. The universal Wilden Drum Pump Kit allows Wilden ¼" and ½" pumps to install directly to drums for efficient and cost-effective product transfer. The kit is available in a variety of materials for full compatibility with most fluids. The pump kit can be adapted to various drum sizes from 5 to 55-gallons
22:1 7.2 2 121 650484-X43 3 SS A / D 2” M 1” F 4¼” 1009 19.5 66301 4 - -
23:1 13.9 2 238 650683-X43 3 SS A / D 2” M 1” F 6” 1009 21.0 66300 4 - -
23:1 56.7 2 980 650967-X6D-B SS A 2” M 1” F 12” 1143 63.6 6694X 4 - -
28:1 1.4 2 24 NM2328A-11-X11 SS - ½” ¼” F 3” 552 5.9 66066 4 - -
30:1 4.9 2 90 650485-X43 3 SS A / D 2” M 1” F 4¼” 1009 19.5 66302 4 - -
40:1 13.9 2 238 650883-X4D-B 3 SS A / D 2” M 1” F 8” 1106 30.9 66300 4 - -
45:1 7.2 2 121 650684-X43 3 SS A / D 2” M 1” F 6” 1009 21.0 66301 4 - -
45:1 20.4 2 339 650863-X4D-B Steel B 2” F 1” F 10” 1166 60.0 66475 4 - -
60:1 4.9 2 90 650685-X43 3 SS A / D 2” M 1” F 6” 1009 21.0 66302 4 - -
65:1 20.4 2 339 650963-X4D-B Steel B 2” F 1” F 12” 1168 66.8 66475 4 - -
Max bar inlet
10.2
10.2
10.2
10.2
10.2
10.2
10.2
8.1
10.2
6.1
10.2
10.2
10.2
6.1
10.2
10.2
8.1
8.1
6.9
6.9
6.9
Max bar outlet
10.2
20.4
20.4
40.8
40.8
91.8
91.8
81.0
112.2
91.5
183.6
224.4
234.6
140.3
285.6
306.0
324.0
364.5
310.5
414.0
448.5
Other bulk supply components A - 65138 Floor mount B - Material hose with fittings: 628089-2 (60 cm) or 628089-6 (180 cm) Air supply hose and ball valve available on request
Floor stands with 3” NPT female inlet and ¼” NPT vent plug
Floor stand
For pump with footprint
65138 A
65139 B
65139
612041-3 NM2304A-41
650483-X43 NM2304A-11
Footprint conversion kits Part number 67137 to install footprint “C” pumps. Part number 67136 to install footprint “D” pumps on footprint “A” stand or follower plate.
Mufflers for Piston Pump Air Motors
91790 1¼”
92460 1¼”
66718 Bolted
61880 ½”
61879 ⅜”
66575 ½”
Model Air inlet Air Motor
2”
2”
3”
3¼” - 6”
8”
10” - 12”
91790
1 At 120 cycle per minute. 2 At 60 cycle per minute. M = Male NPT pipe thread, F = Female NPT. 3 Optional “Ultra” coated stainless steel plunger instead of hard chrome plated (for most models replace last “3” with “B”). Most models feature Ultra High Molecular Weight Polyethylene, other packing options available. 4 Lower pump section only
Wet-Sol Designed to prolong packing life by keeping rod and packings wetted. 66333-B Quart 66334-B Gallon
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
For pump dimensions, service kits and common accessories, see pages 6 to 1010
Piston Pumps Ratio Capacity
(LPM) Max bar
inlet Max bar outlet
cm3 / Cycle Model Wet part Footprint Inlet Outlet Air
Motor Height Weight Lower Pump
12:1 12.4 1 10.3 123.6 204 650491-X43-B Steel A 1” F 4¼” 1312 29 66243-
13:1 39.4 1 8.1 105.3 662 650871-XXE-C Steel B 1½” F 8” 1330 57 66 236-
20:1 39.6 1 6.3 126.0 662 650875-XXE-C Steel B 1½” F 10” 1302 65.3 66236-
22:1 3.7 1 10.3 226.6 31 NM2322E-11-P43 3 Steel C ½” F 3” 857 13 6710X
22:1 3.7 1 10.3 226.6 31 NM2322F-11-P43 3 SS C ½” F 3” 857 13 6710X
23:1 6.8 1 10.3 236.9 114 650492-X43-B Steel A 1” F 4¼” 1311 28.9 66266-
23:1 12.4 1 10.3 236.9 204 650691-X43-B Steel A 1” F 6” 1311 30.4 66243-
28:1 22.9 2 8.1 226.8 328 650888-XXD Steel B 1¼” F 8” 1304 63.5 67300-
30:1 39.6 1 6.3 189.0 662 650971-XXE-C Steel B 1½” F 12” 1302 66.8 66236-
43:1 3.4 1 10.3 442.9 47 67120-P43 3 Steel C ½” F 4¼” 1006 20 6710X
43:1 3.4 1 10.3 442.9 47 67121-P43 3 SS C ½” F 4¼” 1006 20 6710X
44:1 14.3 1 8.1 356.4 204 650891-XXD-C Steel A 1” F 8” 1328 40.4 66243-
44:1 22.9 1 6.3 277.2 328 650889-XXD Steel B 1¼” F 10” 1276 74.8 67300-
46:1 6.4 1 10.3 473.8 114 650692-X43-B Steel A 1” F 6” 1311 30.4 66266-
65:1 22.9 2 6.3 409.5 328 650989-XXD Steel B 1¼” F 12” 1276 74.8 67300-
1 At 60 cycle per minute. 2 At 75 cycle per minute. M = Male NPT pipe thread, F = Female NPT. 3 Optional cup style lower packing (instead of grooved), replace last “3” with “8”.
Application by Material Viscosity (for guidance only): • 25,000 - 50,000 cP Any extrusion pump without ram, or properly sized ball
valve pump with ram • Ca. 100,000 cP Any extrusion pump with ram, possibly also high-ratio
extrusion pump without ram • Ca. 200,000 cP Extrusion pumps 20:1 ratio or higher, equipped with ram • Over 500,000 cP Large displacement (0.66l) extrusion pumps or high-ratio
(≥43:1) extrusion pumps with ram Typical Applications (for consistent and trouble-free transfer): • Printing / Packaging: Inks, adhesives, coatings • Automotive: Mastics, adhesives and sealants • Construction: Caulks, adhesives and RTV silicones • Assembly: Adhesives, caulks, mastics and sealants
All pumps with 6” stroke, except NM2322 (3”) and 6712X-X (4”). Recommended cycling for the pumps is up 10-20 cycles per minute.
3:1 Ratio Diaphragm Pump Electro-polished passivated stainless steel wet end, valve seats and valve balls, with aluminium centre body. Alternative hardened stainless steel valve seats / balls available. The very best features of the Ingersoll Rand / ARO diaphragm pumps: • Seal-less design • Unstallable air valve • Excellent compatibility (including
abrasive materials) • High pressure (300 psi) outlet • Up to 98 litres/min free flow Typical applications include paint recirculation, filter press, adhesives, inks, resins, etc.
BSP = British Standard Pipe thread. NPT = National (US standard) Pipe Thread. ANSI = US standard, applicable for flanged connections.
For pump dimensions, service kits and common accessories, see pages 6 to 1011
UL79
SUMP
Advantages • Rugged Cast Iron Construction • Flow rates up to 870 litres per minute • Screened Inlet • 2½” Ported Outlet • Will pass through 222 x 222 mm
opening
Speciality Pumps Rotary Sump Pumps
for the Construction Industry
Designed for maintenance, waste and bore-hole applications where a light- weight and compact pump is required, the Ingersoll Rand Sump Pump range go two steps further, adding low air consumption and high output rates into the equation… Available in two models, the pump is designed to run on a rotary cycle giving a constant flow rate of 200 (757 LPM) or 230 GPM (870.5 LPM) dependant on model. The rotary system uses centrifugal forces to thrust the media through your pipe-work, creating massive suction via the bottom grilled inlet under flooded suction. Each unit is constructed in full cast iron, made to be dropped into the worst of conditions.
P237AX-EU P35A1-EU
Applications
For simple batching operations, the ARO® TRON Mini-Batcher is the perfect choice. Featuring simple programming, friendly prompting screen, modular design and large “on-off” buttons, the Mini-clean, consistent batching.
67161-2
ARO® Pneumatic batch counter kits control the volume of fluid dispensed by controlling the number of pump cycles. Since all ARO Diaphragm pumps are positive displacement pumps, with a known displacement, the number of pump cycles, times the pump’s displacement, equals the total volume dispensed. These retro-fit kits are totally pneumatic (except for the solenoid operated remote start models) and are therefore explosive proof.
67072
This device senses the back pressure or lack of back pressure on the end of tubing that is located in tank or sump. The tubing is strategically placed at a desired level or levels. When an input occurs the pneumatic signal output from this device is used to actuate an air valve.
High level - 59916-1 Low level - 59916-2
Pneumatic Batch Counters
Diaphragm Failure Detection
The ARO® Diaphragm failure detection pump warns of a diaphragm failure by sensing the presence of liquid in the air chamber of the pump. This system uses a liquid sensor in each of the two air sides and a control box mounted on the pump. The box contains circuitry with a latching SPDT relay. The relay can con-trol various valves or warning devices and will stay latched until reset by operator.
To meet UL79 specifications, pumps utilise pressure relief valves to limit dispensing line pressure to under 50psi.If line pressure between the pump and the dispensing point exceeds 50psi due to thermal expansion, line compression, back-feed, or gravity, the pressure relief valve opens and bleeds off the excess pressure. The relief valve must be plumbed to return the bleed-off fuel to the storage container.
Designed specifically for high-volume transfer, bulk , unloading or fuelling applications. The pumps meet UL79 specification code and are compatible with gasoline, aviation fuel, diesel fuel, fuel oil, kerosene, and unleaded fuel.
Fuel Pumps
UL Pumps Certified Unleaded Transfer
For pump dimensions, service kits and common accessories, see pages 6 to 1012
Be sure to check out our site, www.airpumping.co.uk where you can download full ATEX guidelines and find out more on how to ensure your ATEX certified
Pump Size
Pro Flo® Series 6mm (1/4”), 13mm (1/2”), 25mm (1”)
Up to 46% energy operating cost savings over competition on Smart Carbon Pumps, 68% on Metallic Range!!
½”, 1”,1½”, 2” and 3” fluid inlet/outlets Grounded to prevent build up of static charge Unique Smart Carbon Fibre on non metallic range Flow rate up to 696 Litres per min up to 1041 Litres per min Choice of diaphragm material Unique Smart Carbon Fibre non-metallic air valve design for unparalleled
safety
Most Technologically Advanced Air Operated Diaphragm Pump
The ARO Pumps are unique in the fact that almost any Ingersoll Rand metallic pump can be grounded and considered ATEX approved (with certification), meaning that to become ATEX certified is a predominately straight forward task to complete. Alternatively if you are looking for a long term saving, the EXP ATEX range offers phenomenal efficiency savings alongside excellent flow rates and ATEX approval, making them one of the most cost effective pumps on the market today!
It is only natural that the worldwide leading producer of air-operated, double-diaphragm pumps complies with the ATEX 95 directive for explosive atmospheres. We take responsibility for not only the product, but also for the supporting documentation and compliance of necessary directives. Wilden introduces the metallic X pumps that comply with ATEX 94/9/EC Group I, category M2 and Group II, category 2 zones G & D. Plastic X pumps comply with ATEX 94/9/EC Group II, category 2, zone G.
Hygienic pumps are made of highly polished stainless steel, in either SL (304) or UE (316L) with surface quality up to 0.5µm. Engineered specifically for usage in food, pharmaceutical, cosmetic and beverage industries, they even come with FDA approved elastomer materials. Large ball valve clearances make these pumps ideal for handling product with suspended particles or solids such as fruit or vegetable, without damaging the product, delivering a pumping solution that is reliable and far above industry standards. Available with all sorts of options to suit your application, the hygienic ranges (from DEPA, Wilden & Ingersoll-Rand / ARO) are fully versatile with CIP (clean in place) and SIP (sterilise in place) functionality inherent in the design. Dairy tube fittings, Aseptic DIN 11864, Tri-clamp, flanged and Neumo fluid connections can all be
supplied on application. For maximum contamination containment, lube-free internal and external air control valves can be fitted, making these pumps not only intrinsically secure, but also super safe. These units are designed with the sole purpose of hygienic fluid solutions in mind so are perfect for any situation where sterile operating conditions are a must!
ATEX Rated Pumps
Hygienic Pumps for Food & Sanitary applications
Lubrication Systems Thunder Pumps
RELIABLE - Rugged housing contains stall-free, ice-free motor technology FEWER PARTS - 50% less parts than the majority of comparable pumps NO MECHANICAL ASSIST - No trip rods or push pins NO SPECIAL TOOLS - Standard tools allow you to service quick, easily & within minutes INLINE SERVICE - Avoid costly removal or downtime, easy access allows overhaul in-situ ALL WEATHER - Seal kits mean all weather pumping without fear of contamination, inside or out! LUBE FREE AIR MOTOR
From the pump maker that knows the lube business better than anyone, Ingersoll Rand / ARO bring you the Thunder pump. Specially designed for viscous duties, these pumps are available in 3:1 or 5:1 ratios for oil duties or 50:1 up to a whopping 100:1 on grease dispensing duties, meaning more pump for your pound!
ATEX Certs.
13
Flap
-Val
ve
Air Pumping Viper TX System & Flap Valve Pumps Vi
per T
X S
elf-
Test
Rig
s Viper TX Mobile Pressure Test Rig
Viper TX Variable Pressure Testing
WARNING!
Air pressure can kill!
Get your rig serviced regularly!
Flap valve pumps constitute a massive portion of the fluid movement industry, and as such need to be strong, lasting, and durable. Built for the most severe of operating conditions flap-valve pumps are designed to pass large amounts of solids, ranging from 1”-3”! These pumps are engineered for long-running and hard duties so are built with ease of maintenance and longevity in mind, meaning less down time and more pumping time. Available in a choice of elastomers and materials to suit your application needs these are some of the most versatile pumps on the market. Recommended for abrasive slurries, suspended & non-suspended solids, and line size solids, flap-valves also have superior top suction and also a bottom discharge, utilising gravity for maximum efficiency.
Ingersoll Rand, SandPIPER and Wilden 1” - 3” Solid Handling
The unit features automatic cut off switches, large variable pressure ranges, and, thanks to the wheeled
design the system is easy to manoeuvre, even when full.
All parts used in the construction of the unit are intrinsically safe and fully ATEX approved (where available).
Save time, money AND energy when it comes to certifying YOUR hoses!
The Viper TX200 unit is a variable pressure, fast fill, test rig system, offering fast and efficient pressure testing of all vessels, hoses, pipelines and systems using ATEX 94/9/EC approved high pressure pumps. Utilising two air operated Ingersoll Rand pumps; one piston pump and one diaphragm pump, the Viper is a marvel in simple efficiency. The pump combination allows for rapid pressurisation of the test subject, with a fully configurable force ranging up to 93.1 bar (1350 psi)! All units come mounted on a trolley for maximum portability in and around the workplace, with non-static non-spark wheels conforming to ATEX where-ever possible. Full upgrade options are available including up rated pressure testing, extra connection points and quick release bleed-offs.
For more detail on the PF20X ARO Flap Valve unit please turn to page 6.
14
Agricultural vehicles
Train systems and services
Heavy goods vehicles
Suitable for... Buses and coaches
Road vehicles
… or any sump, radiator or gearbox!
The Air Pumping auto drain plug replaces the standard traditional drainage plug on any sump application, allowing for hygienic, economic and above all fast fluid changes - making health, safety and environmental issues with waste fluids a thing of the past! Just connect up a drainage line to the plug, and as you screw onto the thread, the plug will start to evacuate! Simple and effective.
Make sump fluid changes quick, clean and easy!
Auto Drain Plugs & FluidAir Compressors
What better way to power your diaphragm and piston pumps, or to replace that tired old air compressor than with a Montreal certified, energy efficient Fluidair Compressor! Using the latest technological features, the FluidAir range is designed to produce more air, save you money and generate less heat.
Compressors The range of RST screw compressors cover from 4kw up to 160kw supplying small and large businesses alike. The compressors are designed to give high performance along with efficiency (energy saving) whilst still offering reliability and customer confidence. With dirt filtration down to 0.01 microns and remaining oil content down to 0.003mg/m3 all typical applications (e.g. paint spraying and food processing) can be catered for. Dryers The full range of 'FRD' refrigerant dryers and 'FDD' Desiccant dryers offer 'dew points' for every factory application. The dryers ensure that no moisture will enter the air system and thus possibly cause expensive damage to either control valves or end product.
• Take away the basic health and safety risks with handling waste fluids - no more hazardous fluids on you skin! • Make oil changes and oil sampling quick, clean and easy! • Evacuate tanks in minutes using gravity or a closed loop solution • Waste product can be transported directly to a holding tank or container of your choice • Suitable for all sump applications; any size, any liquid, any temperature! • Permanently replace worn or damaged sump plugs - installs in seconds! • Available in metric, imperial, BSP, NPT, UNF, UNC, etc., and with the optional dust cap it even keeps the Althread clean!
Eliminate the
human to oil contact!
ADP Plugs Sump Relief Plugs
Filters The Fluidair range of 'FP' filters provide piece of mind that the air systems are receiving good clean air. With dirt filtration down to 0.01 microns and remaining oil content down to 0.003mg/m3 for all applications from spray painting to ink transfers are receiving the correct air quality. Oil / Water Separators The 'FCC' range of oil / water condensate cleaners allow for effluent condensate from the compressed air system to be discharged legally in accordance with the "Water Resources Act". In-Line Filter Elements A full range of competitive in-line filter elements are available for most other leading filter manufacturers. Pleated filter media and greater cross sectional filter area provide uncom-promised filter efficiency.
FluidAir Systems
FluidAir Systems Rotary Screw Compressors
15
• Automated Mix-on-Demand System • High Volume Product Delivery • Low Air Pressure running requirements • Self-Priming, Closed-Loop System • Capable of Pumping Various Viscosities • Ideal for Mixing Anti-Freeze & Diluting Strong Liquids • Fully compliant with UK Water Supply (Water Fittings) Regulations 1999
Air Pumping Varimix VX Systems
More options are available, please enquire for further details or browse to www.varimix.co.uk
The Air Pumping Varimix is an on demand, mix-and-dispense system, ideal for mixing water and anti-freeze, or water and screen wash; as and when you need it... and WHERE you need it! Utilising two air-operated double-diaphragm pumps in each design, the fully contained Varimix VX system is reliable, easy-to-use and intrinsically safe. Once fully plumbed in, all you need to do is make sure you don't run out of concentrate! With pump sizes from 1/4 to 1" and builds for a number of different duties, every Varimix is built bespoke to your specification... Offering product self-priming, integral water break-tank (excluding VX002) and the ability to run-dry - the Varimix is perfect for busy garages and maintenance yards. Each Varimix system allows for a variety of product viscosities, flow rate outputs and mix ratios. The two diaphragm pumps within each system give the mixed product an added boost - pushing your mixtures to dispensing points up to 500 metres away!
VX-XXX-X
Pump configuration 200 Ingersoll Rand / ARO ½” pumps Flow rates up to 77 litres per minute (lpm) 2 x dispensing points 201 IR / ARO 1” pumps Flow rates up to 133 lpm 4 x dispensing points 202 IR / ARO ¼” pumps Flow rates up to 27 lpm 1 x dispensing points 002 IR / ARO ¼” pumps (Wall-mounted unit) Flow rates up to 27 lpm 1 x dispensing points
Options W ⅜” Wilden pump option Flow rates up to 50 lpm 2 x dispensing points S Screen wash option Using alternate pump materials D Dosing unit For precise, low-ratio mixes or automated dosing applications
With our unique air operated, double diaphragm pump hire fleet, we have a solution to all your liquid transfer needs! Our units are fully self-priming and intrinsically safe, many with full ATEX approval; whether stand alone or trolley mounted, we keep most material combinations on the shelf - Stainless Steel to Polypropylene, Aluminium to PVDF (Kynar) and Neoprene to PTFE (Teflon) to name but a few! Sporting variable flow rates and a high head capacity, our pumps are the perfect tool for vari ous odd duties you may find you need a short term pump for and especially for applications across the board where budget or urgency is an issue! If you have a particular liquid handling requirement, or are not sure how to get your product moving, contact our pump hires department where our friendly and experienced staff will offer practical advice to help specify the most suitable pump for your task. Whatever your fluid transfers task may be, Air Pumping is sure to have the answer!
Fittings, Regulators & Valves Air Preparation Equipment
Actuators
Air Fittings
Cylinders
Control Valves
Pneumatic Switches
C28223-810
104104-XXX
P29122-600
Diaphragm pumps
¼”, ½” P29122-600
1” P29221-610
1½” P29241-610
2”, 3” F25451-110
1” (3:1) P29231-610
2” C28121-800
2”, 3” P29122-600
4½”, 6” C28241-810
8”, 10”, 12” 28353
Piston pumps
C28361-600
Air Preparation Kits
This document is not intended to extend any warranties regarding the products described herein. Any such warranties or other items or conditions of sale of products shall be strictly in accordance with Air Pumping’s standard terms and conditions of sale for such products, a copy of which is available on request. Product improvement is a continuing goal at Air Pumping, and with our suppliers; therefore designs and specifications are subject to change without notice or obligation. Any logos or other trademarks are used with kind permission of their respective owners. To learn more about Air Pumping Engineering Services Ltd., please visit www.airpumping.co.uk
Airless spray finishing pumps are unique from conventional systems in that air is not used to atomise the product. This reduces overspray and bounce-back giving a higher quality finish to steel, heavy equipment and buildings. Finishing pumps cover a broad range of applications including paints, resins, adhesives, lubricants, varnishes, stains and almost every other substance that can be pumped, making them ideal for any tough or messy substance that needs applying with minimum human contact.
