+ All Categories
Home > Documents > AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig....

AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig....

Date post: 06-Mar-2018
Category:
Upload: hoangquynh
View: 303 times
Download: 5 times
Share this document with a friend
4
Rifle Disassembly 1 Fig. 4 Fig. 2 Fig. 3 Fig. WARNING! Make sure your Rifle is unloaded before you begin any procedures. AK 47/74 - Handguards Installation Instructions Gas Tube and Handguard removal Gas Tube Retaining Lever Rotate the Gas Tube Retaining Lever upward until the Gas Tube can be pulled upward at the back, and off the Rifle (Fig. 2). Using a wrench or a bench vise, gently lock across the flat side portions in back of the Gas Tube. Grab the Handguard firmly and rotate it around the Gas Tube axis until it is exactly upside-down. Push straight down and off the Gas Tube (Fig. 3, 4).
Transcript
Page 1: AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig. 4 Fig. 2 Fig. 3 WARNING! Make sure your Rifle is unloaded before you begin any procedures.

Rifle Disassembly

1Fig.

4Fig.

2Fig.

3Fig.

WARNING!

Make sure your Rifle is unloaded before you begin any procedures.

AK 47/74 - Handguards

Installation Instructions

Gas Tube and Handguard removal

Gas Tube Retaining Lever

Rotate the Gas Tube Retaining Lever upward until the Gas Tube can be pulled

upward at the back, and off the Rifle (Fig. 2).

Using a wrench or a bench vise, gently lock across the flat side portions in back of

the Gas Tube.

Grab the Handguard firmly and rotate it around the Gas Tube axis until it is exactly

upside-down. Push straight down and off the Gas Tube (Fig. 3, 4).

Page 2: AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig. 4 Fig. 2 Fig. 3 WARNING! Make sure your Rifle is unloaded before you begin any procedures.

Picatinny Rails

Alen Key

5Fig.

- 2 -

Upper Handguard

Release the Handguard Locking Lever and remove the Lower Handguard (Fig. 5).

Lower Handguard

Handguard Locking Lever

AK 47/74 Handguards Installation

Step 1. Place the Picatinny Rail on the Upper Handguard (Fig. 6).

6Fig.

Page 3: AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig. 4 Fig. 2 Fig. 3 WARNING! Make sure your Rifle is unloaded before you begin any procedures.

- 3 -

11Fig.

7Fig.

9Fig.

8Fig.

Step 2. Holding the Picatinny Rail, place a Nut into designed for it socket, in the

Upper Handguard (Fig. 7).

Step 3. Holding the Nuts fasten Picatinny Rail’s Bolts using the Alen Key (Fig. 8, 9).

10Fig.

Step 4. Place the Upper Handguard on the Gas Tube.

Using a wrench or a bench vise attach the Upper Handguard to the Gas Tube by turning

it 180 degrees (Fig. 10, 11).

Page 4: AK 47/74 - Handguards Installation Instructions - FAB · PDF fileRifle Disassembly Fig. 1 Fig. 4 Fig. 2 Fig. 3 WARNING! Make sure your Rifle is unloaded before you begin any procedures.

- 4 -

43, Yakov Olamy St.

Mishmar Hashiva

ISRAEL 50297

Tel: +972 3 960 3399

Fax: +972 3 960 3312

defense.com-www.fabWebsite:

15Fig.

14Fig.

13Fig.

12Fig.

Forend Cap

Step 5. Place the Lower Handguard on the Rifle’s Receiver (Fig. 12).

Handguard Locking Lever

Step 6. Place the Forend Cap on the Lower Handguard and lock the Handguard

Locking Lever by turning it 180 degrees (Fig. 13).

Step 7. Place the Gas Tube on the Receiver and lock it by turning thе Gas Tube Retaining

Lever down (Fig. 14).

Gas Tube Retaining Lever

Step 8. Assemble weapon (Fig. 15).


Recommended