ALUMINUM ELECTROLYTIC CAPACITORS INDEX 2008 Radial Leaded Full.… · RE Low ESR 105ºC 2000~3000...

ALUMINUM ELECTROLYTIC CAPACITORS 1

INDEX

Series Features ApplicationTemperature

Range(ºC)

LoadLife

(Hour)

CapacitanceRange

(µF)

RatedVoltageRange(V.DC)

Page

Miniature Size

SG Super Miniature (5mm) 85ºC 1000 0.1~330 4~50V 14

SS Super Miniature (5mm) 105ºC 1000 0.1~330 4~50V 16

SN Non Polarized (5mm) 85ºC 1000 0.1~47 6.3~50V 18

MG Smaller Size (7mm) 85ºC 1000 0.1~470 4~63V 19

MI Smaller Size (7mm) 105ºC 1000 0.1~470 6.3~50V 21

MN Non Polarized (7mm) 85ºC 1000 0.1~100 6.3~50V 23

ML Low Leakage for Smaller Size 85ºC 1000 0.1~220 6.3~50V 24

Standard

RG General Used Standard Size 85ºC 1000 0.1~22000 6.3~450V 26

RB General Used Standard Size 105ºC 2000 0.47~15000 6.3~450V 29

LL Low Leakage Current 105ºC 1000 0.1~1000 6.3~50V 32

LG Low Leakage Current 85ºC 1000 0.1~1000 6.3~100V 34

NP Non Polarized 105ºC 1000 0.1~6800 6.3~100V 36

NG Non Polarized 85ºC 1000 0.47~1000 10~250V 38

BP Bi-Polar for Horizontal Deflection 85ºC 2000 2.2~22 25~50V 40

RT Tubular (Axial) 85ºC 1000 0.47~4700 6.3~450V 41

TH High temperature 125ºC 1000 33~1000 10~63V 43

Low Impedance

RE Low ESR 105ºC 2000~3000 4.7~10000 6.3~50V 45

LZ High Ripple Current 105ºC 1000~5000 6.8~10000 6.3~100V 47

LE Low Impedance 105ºC 1000~3000 5.6~6800 6.3~100V 51

ME High Temperature, Low ESR 125ºC 2000~4000 470~3300 6.3~25V 55

MZ ULTRA Low ESR 105ºC 2000 330~3300 6.3~16V 57

ZH Long Life & Low Impedance 105ºC 1000~4000 47~8200 6.3~35V 59

LA Low Impedance for Smaller Size 105ºC 1000 4.7~1000 6.3~35V 62

SMD

VE Miniaturized, Big Capacitance 85ºC 2000 0.1~1500 6.3~100 66

EA High Capacitance Range 85ºC 2000 0.1~6800 6.3~450 68

ES Miniaturized 105ºC 105ºC 1000 0.1~100 6.3~50 70

EU Long Life, 105ºC, 5.7mmL 105ºC 3000 0.1~1000 6.3~50 71

GA Higher Capacitance Range, 105ºC 105ºC 2000 0.1~6800 6.3~450 72

EJ 105ºC 105ºC 2000 0.1~470 6.3~100 74

EH Low Impedance & ESR 105ºC 2000 4.7~1000 6.3~35 75

EZ Low Impedance & ESR, Downsize 105ºC 1000 4.7~220 6.3~50 76

ZH Low Impedance & ESR, Long Life 105ºC 2000~5000 4.7~680 6.3~100 77

UA Hgih Temperature Usage, 125ºC 125ºC 1000 33~1000 10~50 79

EB Non-polarized 85ºC 2000 0.1~47 6.3~50 80

EK Long Life, 105ºC 105ºC 2000~5000 0.1~470 6.3~50 81

EC Low Leakage Current 85ºC 2000 0.1~100 6.3~50 82

ALUMINUM ELECTROLYTIC CAPACITORS2

CAUTION FOR PROPER USE OF ALUMINUM ELECTROLYTIC CAPACITORS IUpon using Aluminum Electrolytic Capacitors, please pay attention to the points listed below.

When the following types of electrical loads indicated below are applied to Aluminum Electrolytic Capacitors, rapid deterioration of electrical property occurs:• Reverse voltage • Voltage exceeds rated working voltage• Rated ripple current is exceeded • Severe charging / dischargingAt such times, severe heat is generated, gas is emitted, then electrolyte leaks from the sealing area, and pressure relief vent operates due to inter-nal pressure.In the worst case, explosion or ignition may occur, and along with destruction of the capacitor combustibles may burst out.

1. CAUTION DURING CIRCUIT DESIGN1-1 OPERATIONAL ENVIRONMENT, MOUNTING ENVIRONMENT AND CONDITIONS. Ensure that operational and mounting conditions follow the specified conditions detailed in the catalog and specification sheets.

1-2 OPERATING TEMPERATURE, RIPPLE CURRENT AND LOAD LIFE Operating temperature and applied ripple current should be within the specified value in the catalog or specification sheets

1-2-1 Do not use Aluminum Electrolytic Capacitors at temperature which exceeds the specified category temperature range. 1-2-2 Do not apply excessive current to the capacitors, which exceeds the specified rated ripple current. During circuit design, please ensure that capacitors are selected to match with the lifetime requirements of the application.

1-3 APPLICATIONAluminum Electrolytic Capacitors are normally polarized. Reverse voltage or AC voltage should not be applied. When polarity of applied voltage is uncertain or when the polarity may flip over, non - polar type capacitors should be used, but the non - polar type cannot be used for AC circuit. Standard Aluminum Electrolytic Capacitors are not suitable for rapid charge and discharge applications.

1-4 APPLIED VOLTAGEDo not exceed the rated voltage of capacitors.

1-5 INSULATIONAluminum Electrolytic Capacitors should be electrically isolated from the aluminum case, cathode lead wire, anode lead wire and circuit pattern. The PVC sleeve of Aluminum Electrolytic Capacitors is not recognized as an insulator, and therefore, the standard capacitor should not be used in a place where insulation function is needed. Please consult with Gen Sales should you require a higher grade of insulating sleeve.

1-6 CONDITIONS OF USEThe following environment should be avoided when using Aluminum Electrolytic Capacitors. 1-6-1 Damp conditions such as water, salt water spray, or oil spray or fumes. High humidity or humidity condensation situations. 1-6-2 Hazardous gas / fumes such as hydrogen sulfide, sulfurous acid gas, nitrous acid, chlorine gas, ammonia or bromine gas. 1-6-3 Exposure to ozone, ultraviolet rays or radiation.1-6-4 Severe vibration or shock which exceeds the condition specified in the catalog or specification sheets.

1-7 CONSIDERATION TO ASSEMBLY CONDITION. In designing a circuit, the following matters should be ensured in advance to the capacitors assembly on the printed Wiring board (PW board). 1-7-1 Design the appropriate hole spacing to match the lead pitch of capacitors. 1-7-2 Do not locate any wiring and circuit patterns directly above the capacitor’s vent. 1-7-3 Ensure enough free space above the capacitor’s vent. The recommended space is specified in the catalog or specification sheets. 1-7-4 In case the capacitor’s vent is facing the PW board, make a gas release hole on PW board.

1-8 CONSIDERATION TO CIRCUIT DESIGNAny copper lines or circuit patterns should not be laid under the capacitor. Parts which radiate heat should not be placed close to or reverse side of the Aluminum Electrolytic Capacitors on the PW board.

1-9 OTHERS Performance of electrical characteristics Of Aluminum Electrolytic Capacitors are affected by variation of operating temperature and frequency. Consider this variation when designing the circuit. Excessive holes and connection hole between both sides on the PW board should be avoided around or under the mounting area of the Aluminum Electrolytic Capacitors on double sided or multilayer PW board. Consider current balance when 2 or more Aluminum Electrolytic Capacitors are connected in parallel. Use bleeder resistors when 2 or more Aluminum Electrolytic Capacitors are connected in series. In this case, the resistors should be connected parallel to the capacitors.

2. CAUTION FOR ASSEMBLING CAPACITORS2-1 CAUTION BEFORE ASSEMBLYAluminum Electrolytic Capacitors can not be recycled after mounting and applying electricity in unit. The capacitors which are removed from PW board for the purpose of measuring electrical characteristics at the periodical inspection should only be recycled for the same position. Aluminum Electrolytic Capacitors may accumulate charge naturally during storage. In this case, discharge through a 1kΩ resistor before use. Leakage current of Aluminum Electrolytic Capacitors may be increased during long storage time. In this case, the capacitors should be subject to voltage treatment through a 1kΩ resistor before use.

2-2 IN THE ASSEMBLY PROCESS - 1Ensure rated voltage and capacitance of the capacitors before mounting. Ensure the capacitor’s polarity before mounting.Do not use a capacitor which has been dropped onto a hard Surface. Do not use capacitors with damaged or dented cases or seals.

2-3 IN THE ASSEMBLY PROCESS - 2


Capacitors should be mounted after confirmation that hole spacing on PW board matches the lead pitch of the capacitors. Avoid excessive force when clinching lead wire during auto-insertion process. Avoid excessive shock to capacitors by automatic insertion machine, during mounting, parts inspection or centering operations. Please utilize supporting material such as strap or adhesive to mount capacitors to PC board when it is anticipated that vibration or shock is applied.

2-4 SOLDERINGSoldering conditions (temperatures, times) should be within the specified conditions which are described in the catalog or specification sheets.In case lead wire reforming is needed due to inappropriate pitch between capacitor and holes on PW board, stress to the capacitor should be avoided. In case soldered capacitor has to be withdrawn from the PW board by soldering irons, the capacitor should be removed after solder has melted sufficiently in order to avoid stress to the capacitor or lead wires. Soldering iron should never touch the capacitor’s body.

2-5 FLOW SOLDERINGDo not dip capacitor’s body into melted solderSoldering condition (preheat, soldering temperature, dipping time) should be within the specified standard which is described in the catalog or specification sheets. Flux should not be adhered to capacitor’s body but only to its terminals. Other devices which are mounted near capacitors should not touch the capacitors.

2-6 REFLOW SOLDERINGReflow soldering conditions (preheat, soldering temperature, reflow time) should follow the specified standard which are described in the catalog or specification sheets. Heating standard should depend on surface of the capacitor color or materials when infrared rays are used because the capacitor’s heat ab-sorption depends on the surface color or materials. Check heat condition. Standard Aluminum Electrolytic Capacitors can not withstand two or more reflow processes. Consult with Gen Sales when two or more reflow processes are needed.

2-7 HANDLING AFTER SOLDERINGDo not bend or twist the capacitor’s body after soldering on PW board. Do not pick-up or move PW board by holding the soldered capacitors. Do not hit the capacitors and isolate capacitors from the PW board or other device when stacking PW boards in store.

2-8 PW BOARD CLEANINGStandard Aluminum Electrolytic Capacitors should be free from halogenated solvents during PW board cleaning after soldering. Use solvent proof capacitors and follow the specified cleaning condition when halogenated solvents are used. Solvents should have well controlled conductivity, pH, specific gravity and Water contents during the cleaning of solvent proof capacitors. Cleaned PW board with capacitors should not be kept in solvent environment or nonventilated places. Let PW board containing capacitors after cleaning dry with hot blast fully. The temperature of such breeze should be under the Upper category temperature of capacitors.

2-9 ADHESIVES AND COATING MATERIALS. Do not use halogenated adhesives and coating materials to fix Aluminum Electrolytic Capacitors. Flux between the Surface of the PW board and sealing of capacitors should be cleaned before using adhesives or coating materials. Solvents should be dried up before using adhesives or coating materials. Do not cover up all the sealing area of capacitors with adhesives or coating materials, make coverage only partial.

3. CAUTION DURING USE OF CAPACITORS IN SETSDo not touch the terminals of capacitors.Do not connect electrical terminals of the capacitor. Keep the capacitors free from conductive solution, such as acid, alkali and so on. Ensure the operational environment of the equipment in which the capacitor has been built is within the specified condition mentioned in the catalog or specification sheets.

4. MAINTENANCEPeriodical inspection should be carried out for the capacitors, which are used with industrial equipment. Check the following points at the inspection. 4-1 Visual inspection to check pressure relief open or leakage of electrolyte.4-2 Electrical characteristics: leakage current, capacitance, dissipation factor and the other points which are mentioned in the catalog or specifica-tion sheets.

5. EMERGENCY ACTIONWhen the pressure relief vent is open and some gas blows out from the capacitor, please turn the main switch of the equipment off or pull out the plug from the power outlet immediately. During pressure relief vent operation, extremely hot gas (over 100˚C) may blow out from the capacitors. Do not stand close to the capacitors. In case of eye contact, flush the open eye (s) with large amount of clean water immediately. In case of ingestion, gargle with water immediately, do not swallow, do not touch electrolyte but wash skin with soap and water in case of skin contact.

6. STORAGE CONDITIONAluminum Electrolytic Capacitors should not be stored in high temperatures or where there is a high level of humidity. The suitable storage condition is 5˚C ~ 35˚C and less than 75% in relative humidity.Aluminum Electrolytic Capacitors should not be stored in damp conditions such as water, saltwater spray or oil spray. Do not store Aluminum Electrolytic Capacitors in an environment full of hazardous gas (hydrogen sulfide, sulfurous acid gas, nitrous acid, chlo-rine gas and ammonia or bromine gas). Aluminum Electrolytic Capacitors should not be stored under exposure to ozone, ultraviolet rays or radiation.

7. DISPOSALPlease take either of the following actions in case of disposal. 7-1 Incineration ( high temperature of more than 800˚) after crushing the capacitor’s body 7-2 Consignment to specialists of industrial waste.


CAUTION FOR PROPER USE OF ALUMINUM ELECTROLYTIC CAPACITORS II1. POLARITY MARKING OF ELECTROLYTIC CAPACITORS

Please confirm the polarity to avoid applying any reverse voltage or AC voltage to the capacitors.

2. MOUNTING CAPACITORSAluminum Electrolytic Capacitors are designed to open the pressure relief vent and release hot gas including electrolyte through it, in abnormal cases such as when reverse voltage or excess voltage was applied, or when ripple current exceeding the permissible value has flown into capaci-tors .

Do not design to locate any wiring or circuit pattern around the capacitor’s pressure relief vent. The pressure relief vent bulges right before the vent operation. Ensure enough free space directly above the capacitor’s vent as shown in the below table so that bulged vent never touches to an object such as the case on cover of the set. The pressure relief vent will not open without the appropriate free space. The distance between the terminals holes on the circuit board should be the same as that between the lead wires or terminals of the capacitor. Excessive force in mounting on circuit boards should be avoided.Improper insertion of the lead wires in circuit board may cause electrolyte leakage, break the lead wires or impair their connection with the internal elements.When the distance between the two terminals holes on the circuit board cannot be reduced to that between the lead wires, lead formed capacitors are recommended.

3. VOLTAGE TREATMENTThe following voltage treatment should be done on the capacitors that have been stored for a long time. Voltage Treatment

Prior to the initial measurement , the capacitors shall be applied with a DC Voltage Which is equal to the Rated Voltage of the capacitor through a resistor of about 1 kΩ in series for 1 hour , and then discharged through a resistor of about 1Ω/ Volt.

4. RIPPLE CURRENT4-1 The combined value of D.C. voltage and the peak A.C. voltage shall not exceed the rated voltage and shall not be reverse voltage. 4-2 Use of aluminum electrolytic capacitor under ripple voltage with wide amplitude is equivalent to quick charge- discharge operation. If ripple voltage with the amplitude over 70Vp-p is expected, please contact us.

5. PW BOARD CLEANING5-1 PW board can be immersed or ultrasonically cleaned using suitable cleaning solvents for up to 5 minutes (5L and 7L is up to 3 minutes) and up to 60˚C maximum temperatures about 100wv following. The board should be thoroughly rinsed and dried. Recommended cleaning solvent include Pine Alpha ST-100S, Clean-thru 750H, IPA (isopropyl alcohol)

The use of ozone depleting cleaning agents are not recommended in the interest of protecting the environment. Please consult us for additional information about acceptable cleaning solvents or cleaning methods.

5-2 Avoid using the following solvent groups unless specifically allowed for in the specification; Halogenated cleaning solvents: except for solvent resistant capacitor types, halogenated solvents can permeate the seal and cause internal capacitor corrosion and failure. For solvent resistant capacitors, carefully follow the temperature and time requirements of the specification. 1-1-1 trichloroethane should never be used on any aluminum electrolytic capacitor. Alkali solvents: could attack and dissolve the aluminum case. Petroleum based solvents: deterioration of the rubber seal could result. Xylene: deterioration of the rubber seal could result. Acetone: removal of the ink markings on the vinyl sleeve could result.

5-3 A thorough drying after cleaning is required to remove residual cleaning solvents which may be trapped between the capacitor and the circuit board. Avoid drying temperatures which exceed the upper category temperature of the capacitor. 5-4 Monitor the contamination levels of the cleaning solvents during use by electrical conductivity, pH, specific gravity, or water content. Chlorine levels can rise with contamination and adversely affect the performance of the capacitor.

6.ELECTROLYTE AND SEPARATOR PAPER ARE FLAMMABLE Electrolyte and separator paper used in Aluminum Electrolytic Capacitors are flammable. Also, Electrolyte is electrically conductive. Therefore, in case Electrolyte gets contact with PC board, it may cause corrosion of circuit pattern, or tracking or short circuit between patterns, and may lead to smoke generation or ignition at the worst cases. Please make considerations to the above risk in designing circuit patterns and determining the mounting method and mounting location of capaci-tors.

7. FUMIGATION AND HALOGENATED FLAME RETARDANTIt may cause corrosion of internal electrodes, aluminum cases and terminal surface when the following conditions exist. 7-1 Fumigation of wooden pallets before shipment to disinfect vermin. 7-2 Existence of components or parts that contain halogenated flame retardant agent (bromine etc.) together with capacitors.


MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS SERIES CHART

6

PARTS NUMBER SYSTEM FOR THE RADIAL TYPE

987654321Product Series Capacitance Capacitance

ToleranceRated

VoltageCase Sizeø(DxL)mm

Logo Color Option

Product CodeElectrolyticCapacitors EC

Classification Code

Miniature Type

SG

SS

SN

MG

MI

MN

ML

Standard Type

RG

RB

LL

LG

NP

NG

BP

RT

TH

Low Impedance

ME

LE

MZ

ZH

LZ

RE

LA

Cap.(μF) Code0.1 0R1

0.22 R22

1 010

4.7 4R7

10 100

47 470

100 101

470 471

1000 102

4700 472

10000 103

Cap. Tolerance Code±5% J

±10% K

±20% M

+20-0% N

+20-10% V

+30-10% Q

+50-10% T

+80-20% Z

Special S

Voltage(V) Code2.5 2R53.3 3R34 004

6.3 6R310 01016 01625 02535 03550 05063 063100 100160 160330 330450 450

Case Size Code

3x5 0305

4x5 0405

4x7 0407

5x5 0505

5x7 0507

5x11 0511

6.3(6)x5 0605

6.3(6)x7 0607

6.3(6)x11 0611

8x5 0805

8x7 0807

8x9 0809

8x10 0810

8x11 0811

8x12 0812

8x14 0814

8x16 0816

8x20 0820

10x10.5 1010

10x12 1012

10x15 1015

10x16 1016

10x20 1020

10x25 1025

10x30 1030

13x16 1316

13x21 1321

13x26 1326

16x16 1616

16x26 1626

16x32 1632

This code depends on the customers

request. It could be identified the logo

on the sleeve.

Color Code

Black/Gold B

Black/White W

Green/Gold G

Green/White H

Purple/Gold P

Purple/White U

Orange 0

Navy-Blue/Gold N

Navy-Bule/Black A

Navy-Blue/While V

Coffee/White C

Hyal-Blue L

HyaI-Yellow Y

Hyal-White T

Hyal-Orange R

Description CodeBulk B

Taped T

Lead cut C

Other O


Failure mode故障型式

Failure mechanism內部現象

Causes 發生原因

Production factor 製造時 Application factor 使用時

TYPICAL FAILURE MODES AND THEIR FACTORS

Short circuit短路

Open開路

Electrolyte leakage漏電解液

Capacitance reductiontanδ increase

靜電容量減少，tanδ增加

Vent Operation壓力閥動作

Leakage current increase漏電流增加

Shot circuit between elec-trodes

電極間短路

Breakdown of lead tab 導針斷線

Insufficient sealing密閉不完全

Corrosion腐蝕

Electrolyte deteriorationand reduction 電解液老化、減少

Reduced anode foilcapacitance

陽極箔的靜電容量減少

Reduced cathode foilcapacitance

陰極箔的靜電容量減少

Internal pressure increase內壓上升

Deterioration of oxide film氧化膜的劣化

Electrode-cutting burrs(metal particles)電極切割時的金屬微粒

Mechanical stress機械的壓力

Insuffcient connection oflead tab

導針接觸不完全

Improper sealing封口不完全

Halogen infiltration滷化物滲入

Shortage of electrolyte電解液不足

Abnormalmechanical stress

異常的機械壓力

Deterioration ofsealant material

封口材料老化

Use of halogenated solvent使用含滷化物的清洗劑

Use of coating material使用塗料

Use of adhesive使用黏著劑

Usage for a longperiod of time

長時間的使用

Excessive ripple current過大的濾波電流

Usage at a high temperature超過額定溫度的使用

Reverse voltage applied逆電壓的使用

Severe charging/ discharging過渡激烈的充放電

Excessive voltage applied超過額定電壓的使用

AC voltage applied使用交流電


TAPING SPECIFICATIONSLead taping is designed for automatic insertion equipment. Capacitors with case size of 10mm x 16mm or smaller are available in taping type.

D5(mm) W±5(mm) L±5(mm) H±5(mm) Quantity(PCS)

4 245 340 50 2500

5 245 340 50 2000

6.3 245 340 50 1500

8 245 340 50 1000

10(L≤16) 245 340 50 600

D(mm) A±5(mm) B±5(mm) C±5(mm) Inner Box Quantity(PCS)

4 245 340 50 10 2500

5 245 340 50 10 2000

6.3 245 340 50 10 1500

8 245 340 50 10 1000

10(L≤16) 245 340 50 10 600

PACKING (TAPING)Available for various automatic insertion equipment. Choosing the ordinal polarity of lead of capacitors depends on customer’s request.

Line for tear off

Ammo

Inner Box


Item項目

Symbol符號

Case Size外殼尺寸

Tolerance誤差範圍

Remark備註

4x5 5x5 6.3x5 8x5 4x7 5x7 6.3x7 8x7 5x11 6.3x11 8x11 10x12 10x16 10x20

Lead wire diameter導針線徑

d 0.45 0.5 0.6 ±0.05

Intervals of bodies電容主體間的距離

p 12.7 ±1.0

Intervals of punches holes孔洞間的距離

P0 12.7 ±0.2

Distance between holes and lead wire孔洞與導針的距離

P1

3.85

±0.7

Fig1.Fig4.

5.355.1

5.355.1 5.1

Fig2. F1=5.0 ±0.5

5.1 5.6 Fig2. F1=5.0 ±1.0

5.6 5.35 5.1 5.1 5.6 5.35 5.1 4.6 5.35 5.1 4.6 Fig3. F1=5.0 ±1.5

Distance between holes and bodies孔洞與主體的距離

P2 6.35 ±1.0

Distance between lead and lead導針與導針的距離

F

5.0

+0.8 -0.2

Fig1.Fig4.

2.02.5

2.02.5 2.5

Fig2:

2.5 2.5

1.5 2.0 2.5 2.5 1.5 2.0 2.5 3.5 2.0 2.5 3.5

Base tape width帶子基底的寬度

W 18.0 ±0.5

Adhesive tape width熱溶膠帶的寬度

W0 12.5 Min

Deviation between holes and base tape孔洞與帶緣的距離

W1 9.0 ±0.5

Distance between body button and tape center主體底部到帶子中心點的距離

W2 1.5 Max

Distance between body bottom and tape center主體底部到帶子中心點的距離

H 17.5 18.5 ±0.75

Lead wire clinched height導針彎折的高度

H0 16.0 ±0.5 Fig1.2

Distance between body top and tape center主體上端到帶子中心點的距離

H1 24.5 27.5 32.5 33.0 36.0 38.0 Max

Punched hole diameter孔洞的直徑

D0 4.0 ±0.3

Lead wire protrusion導針突出部分

ℓ 1.0 Max

Length of not good lead slit不良導針裁切長度

L 11.0 Max

Base and adhesive tape thickness熱溶膠帶的厚度

t 0.7 ±0.3

Deviation of body alignment主體排列的偏差度

Δh 0 ±2.0

Deviation of body alignment主體排列的偏差度

Δh1 0 ±1.0

SPECIFICATION TABLE


Figure 2 Reel

W 52 63 73

B 68 80 90

W : Inside distance between tapes. B : Inside distance between flanges.

TAPING SPECIFICATIONS

1.Taping dimensions are indicated if Figure 1.

2.To identify the orientation, the cathode tape shall be blue and the an-node tape shall be white.

3.A minimum 350mm leader tape shall be provided before the first and after the last capacitor on reel.

4.Taped capacitors shall be wound on a packing reel shown on Figure 2.

5.Finished reel shall be packaged in the packaging box shown on Figure 3.

QUANTITY OF PACKAGING

Dia. of capacitor (mm) Reel(pcs) Ammo.(pcs)

5 2000 1500

6 1500 1000

8 1000 1000

10 500 500

Note : Above quantities principle. Some difference may be provided.

Figure 1 Taping

Symbol Dimension(mm)

D 5, 6, 8, 10

d 0.5, 0.6

P 10 (For Dia. 5, 6, 8), 15 (For Dia. 10)

W 52+1.5-1.0, 63+1.5-1.0, 73±1.5

g 0.6 max

L-1 ~ L-2 1.0 max

Z 1.2 max

t 3.2 min (Lead ends shall not extend beyond the tape.)

T 6.0±0.5

Figure 3 Packing Box

W 52 63 73

A 81 93 103

W : Inside distance between tapes. A : Width of packaging box. Unit(mm)

TAPED AND REELED (AXIAL)This specification describes the lead taping packaging for electrolytic capacitor with axial lead and radial lead for automatic insertion systems.


LEAD CUT AND FORMING

Straight lead cut: Lead cut for radial lead type is available Standard cut lead length is 3.0±0.5mm

3.0

Hockey stick lead forming Available for less than 8mm Dia. Products only.

Self-mounting radial lead type (a). Case Dia. 5Ø, 6Ø and 8Ø

Self-mounting radial lead type (b).Case Dia 10Ø, 13Ø, 16Ø, and 18Ø

Case Dia. D H1±0.5 H2 F±0.5 d

5 5.0 2.7 5.0 0.5

6 5.0 2.7 5.0 0.5

8 5.0 2.7 5.0 0.5

10 5.0 2.7 5.0 0.6

13 5.0 2.7 5.0 0.6

16 5.0 2.7 7.5 0.8

18 5.0 2.7 7.5 0.8


CAPACITOR CASE SIZE

(mm)

INNER BAG Q’TY

NUMBER of BAGS

(PER INNER BOX)

INNER BOX Q’TY

OUTER BOX Q’TY

BAG SIZE(cm)

INNER BOX SIZE (cm)

OUTER CARTON

SIZE(cm)

Ø4x5 2000 20 40000 80000 19x22

29x18x23 39x32x25

Ø4x7 2000 20 40000 80000 19x22

Ø5x5 2000 15 30000 60000 19x22

Ø5x7 2000 15 30000 60000 19x22

Ø5x11 1000 15 20000 40000 19x22

Ø6x5 2000 10 20000 40000 23x23

Ø6.3x7 2000 10 20000 40000 23x23

Ø6.3x11 1000 15 15000 30000 19x22

Ø8x9 1000 8 8000 16000 18x30

Ø8x11 500 12 6000 12000 18x30

Ø8x12 1000 6 6000 12000 18x30

Ø8x14 500 12 6000 12000 18x30

Ø8x15 500 12 6000 12000 18x30

Ø8x20 500 10 5000 10000 18x30

Ø10x12 500 10 5000 10000 18x30

Ø10x15 500 8 4000 8000 18x30

Ø10x16 400 10 4000 8000 18x30

Ø10x20 300 10 3000 6000 18x30

Ø10x25 250 10 2500 5000 18x30

Ø12.5x20 200 9 1800 3600 18x30

Ø13x15~18 500 8 4000 8000 19x22

Ø13x21 150 10 1500 3000 18x30

Ø13x25 150 10 1500 3000 18x30

Ø13x31 80 15 1200 2400 18x30

Ø16x26 100 12 1200 2400 18x30

Ø18x32 40 20 800 1600 18x30

Ø18x36 40 20 600 1200 18x30

Ø18x41 40 20 600 1200 18x30

PACKING SPECIFICATION (BULK)


ELECTROLYTIC CAPACITORS FLOW CHART

DELIVERY

IQC

IQC

IQC

IQC

IQC

IQC

IQC

IPQC

IPQC

IPQC

OQC

QA

CATHODE FOIL

ANODE FOIL

LEAD WIRE

SEPARATOR

RUBBER BUNG

ALUMINUM CAN

ELECTROLYTE

STITCHING

SLITTING

WINDING

SLEEVE

IMPREGNATION

SEALASSEMBLY

WASH

SLEEVING

LOADING

AGING

TESTINGAPPEARANCE INSPECTION

LEAD CUTTING OR TAPING

PACKING

COMPLETION

ALUMINUM ELECTROLYTIC CAPACITORS

14

FEATURES Super Miniature - 5mm

SPECIFICATIONItem Characteristic

Operation Temperature -40 ~ 85°C

Rated Working Voltage 4 ~ 50 V.DC

Capacitance Tolerance (120Hz 20°C) ±20% (M)

Leakage Current(120Hz 20°C)

I ≤ 0.01CV or 3 (μA) maxWhichever is greater after 2 minutes

I : Leakage Current(μA) C : Rated Capacitance(μF) V : Rated Voltage(V)

Surge Voltage(120Hz 20°C)

WV 4 6.3 10 16 25 35 50

SV 5 8 13 20 32 44 63

Dissipation Factor (120Hz 20°C)(tan δ)

WV 4 6.3 10 16 25 35 50

tanδ 0.35 0.24 0.20 0.16 0.14 0.12 0.10

Low Temperature Stability

Impedance ratio at 120Hz

Rated Votage (V) 4 6.3 10 16 25 35 50

-25°C/+25°C 7 4 3 2 2 2 2

-40°C /+25°C 15 8 6 4 4 3 3

Endurance (Load Life)

After 1000 hours application WV at +85°C, the capacitor shall meet the following limits.

Capacitance Change ≤ ±25% of initial value

Dissipation Factor ≤ 200% of initial specified value

Leakage Current ≤ initial specified value

Shelf Life

After 500 hours application of WV at +85°C the capacitor shall meet the following limits.




DIMENSIONS (mm)

D 4 5 6.3 8

F 1.5 2.0 2.5 3.5

d 0.45 0.45 0.45 0.50

α 1.5 1.5 1.5 1.5

L + α(max)

SGSG SeriesSG


CASE SIZE & MAX RIPPLE CURRENT

µFWV 4 / 0G 63 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H

ITEM DxL R.C. DxL R.C. DxL R.C. DxL R.C. DxL R.C. DxL R.C. DxL R.C.

0.1 → 4x5 3

0.15 → 4x5 4

0.22 → 4x5 4

0.33 → 4x5 5

0.47 → 4x5 6

0.68 → 4x5 8

1.0 → 4x5 9

1.5 → 4x5 12

2.2 → 4x5 13 4x5 14

3.3 → 4x5 14 4x5 16 4x5 17

4.7 → 4x5 16 4x5 17 4x5 19 4x5 20

6.8 → 4x5 17 4x5 19 4x5 21 5x5 26 6.3x5 32

10 → 4x5 19 4x5 21 4x5 244x5 25

5x5 31 6.3x5 395x5 28

15 → 4x5 24 4x5 26 5x5 33 5x5 35 6.3x5 44 6.3x5 48

22 4x5 24 4x5 294x5 31 4x5 33 5x5 43

6.3x5 556.3x7 60

5x5 36 5x5 40 6.3x5 55 8x7 70

33 4x5 294x5 35 4x5 38 5x5 49

6.3x5 606.3x5

65 8x7 855x5 40 5x5 44 6.3x5 55 8x7

47 4x5 35 5x5 485x5 50 5x5 50 6.3x5 70

8x7 756.3x5 60 6.3x5 65 8x7 85

68 5x5 47 6.3x5 65 6.3x5 70 6.3x5 80 8x7 100

100 6.3x5 65 6.3x5 806.3x5 90 6.3x5 100

8x7 1208x7 100 8x7 110

200 6.3x5 100 8x7 140 8x7 150

330 8x7 140 8x7 170

SG


16 SSSS Series FEATURES

Super Miniature Height 5mm for 105˚C


Operation Temperature Range -40 to +105°C

Rated Working Voltage 4 – 50 V.DC

Capacitance Tolerance(120Hz 20°C) ±20% (M)





WV 4 6.3 10 16 25 35 50

SV 5 8 13 20 32 44 63

Dissipation Factor(120Hz 20°C) (tanδ)

WV 4 6.3 10 16 25 35 50

tanδ 0.37 0.28 0.24 0.20 0.16 0.13 0.12



Rated Voltage (V) 4 6.3 10 16 25 35 50

-25°C/ +25°C 6 3 3 2 2 2 2

-40°C / +25°C 12 8 5 4 3 3 3

Load Life





Shelf Life

After 500 hours application of WV at + 105°C the capacitor shall meet the following limits




SS


DIMENSIONS (mm)D 3 4 5 6.3 8x5 8x7

F 1.0 1.5 2.0 2.5 3.5 3.5

d 0.40 0.45 0.45 0.45 0.45 0.50

α 1.0 1.0 1.2 1.3 1.5 1.5


µFWV 4 / 0G 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H

ITEM D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.1 →3x5 1

4x5 2

0.22 →3x5 2

4x5 4

0.33 →3x5 2.8

4x5 4

0.47 →3x5 4

4x5 5

1.0 →3x5 7

4x5 8

2.2 →3x5 7

4x5 114x5 10

3.3 → 3x5 103x5 11 3x5 11

4x5 13 4x5 14

4.7 → 3x5 11 4x5 14 4x5 154x5 25

5x5 19

10 → 3x5 133x5 14 4x5 20 5x5 25

6.3x5 314x5 19 5x5 23 6x5 28

22 4x5 19 4x5 23 5x5 294x5 28

6.3x5 39 6.3x5 425x5 32

33 5x5 26 5x5 324x5 32

6.3x5 45 6.3x5 48 8x5 665x5 35

47 5x5 32 5x5 385x5 42 5x5 46

6.3x5 50 8x5 726.3x5 48 6.3x5 50

100 6.3x5 555x5 48

6.3x5 726.3x5 80

8x5 996.3x5 65 8x5 99

220 6.3x5 686.3x5 75 8x5 120 8x5 110

8x7 1558x5 104 8x7 132 8x7 140

330 8x5 110 8x5 115 8x7 120

All blank voltage on sleeve marking is the same voltage as “→” point to.

L + α(max)

SS


18

FEATURES Non-Polarized Hight 5mm For 85°C



Rated Working Voltage 6.3 – 50 V.DCCapacitance Tolerance

(120Hz 20°C) ±20% (M)

Leakage Current (120Hz 20°C)


I : Leakage Current(μA) C : Rated Capacitance(μF) V : Working Voltage(V)


WV 6.3 10 16 25 35 50SV 8 13 20 32 44 63


WV 6.3 10 16 25 35 50tanδ 0.24 0.20 0.17 0.17 0.15 0.15


Impedance ratio at 120HzRated Voltage (V) 6.3 10 16 25 35 50

-25°C / +25°C 4 3 2 2 2 2-40°C / +25°C 10 8 6 4 3 3

Load Life

After 1000 hours application of WV at +85°C the capacitor shall meet the following limits. (The polarity needs to exchange every 250 hours)




Shelf Life

After +85°C no voltage application after 1000 hours and then through the aging treatment (reference JIS C 5101-1), the capacitor shall meet the limits for load life characteristics.




DIMENSIONS (mm)D 4 5 6.3

F 1.5 2.0 2.5

d 0.45 0.45 0.45

α 1.0 1.2 1.3

CASE SIZE & MAX RIPPLE CURRENTµF

WV 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1HITEM D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.1 → 4x5 10.22 → 4x5 20.33 → 4x5 2.80.47 → 4x5 41.0 → 4x5 8.42.2 → 4x5 8.4 5x5 133.3 → 5x5 12 5x5 16 5x5 174.7 → 4x5 12 5x5 16 5x5 18 6.3x5 2010 4x5 14 4x5 17 5x5 23 6.3x5 27 6.3x5 2922 5x5 28 6.3x5 33 6.3x5 3733 6.3x5 37 6.3x5 41 6.3x5 4947 6.3x5 45


L + α(max)

SNSN SeriesSN


19

FEATURES Smaller Size - 7mm



Rated Working Voltage 4 - 63 V.DC






WV 4 6.3 10 16 25 35 50 63

SV 5 8 13 20 32 44 63 79


WV 4 6.3 10 16 25 35 50 63

tanδ 0.35 0.24 0.20 0.17 0.15 0.12 0.10 0.10



Rated Voltage (V) 4 6.3 10 16 25 35 50 63

-25°C / +25°C 6 4 3 2 2 2 2 2

-40°C / +25°C 12 8 6 4 4 3 3 3

Load Life

After 1000 hours application of W V at +85°C the capacitor shall meet the following limits.




Shelf Life





DIMENSIONS (mm)

D 4 5 6.3 8

F 1.5 2.0 2.5 3.5

d 0.45 0.50 0.50 0.50

α 1.0 1.3 1.3 1.5

L + α(max)

MGMGSeriesMG



µF

WV 4 / 0G 6.3 / 0J 10 / 1A 16 / 1C

ITEM DxL R. C. DxL R. C. DxL R.C. DxL R. C.

10 4x7 28

22 4x7 34 4x7 38 4x7 42

33 4x7 33 4x7 42 4x7 46 5x7 62

47 4x7 39 4x7 50 5x7 66 5x7 73

100 5x7 65 5x7 87 6.3x7 99 6.3x7 110

220 6.3x7 110 6.3x7 133 8x7 165 8x7 145

330 8x7 165 8x7 180 8x7 210

470 8x7 190

µF

WV 25 / 1E 35 / 1V 50/ 1H 63 / 1J

ITEM DxL R. C. DxL R. C. DxL R.C. DxL R. C.

0.1 4x7 1.3 4x7 1.3

0.22 4x7 3.0 4x7 3.0

0.33 4x7 4.4 4x7 4.4

0.47 4x7 6.3 4x7 6.3

1 4x7 12 4x7 12

2.2 4x7 16 4x7 16

3.3 4x7 118 4x7 19 5x7 24

4.7 4x7 21 4x7 22 4x7 24 6.3x7 33

10 4x7 31 5x7 32 5x7 42 6.3x7 45

22 5x7 55 6.3x7 60 6.3x7 64

33 6.3x7 66 6.3x7 73 8x7 75

47 6.3x7 80 8x7 95 8x7 85

100 8x7 115 8x7 115

MG


21

FEATURES General Used Height 7mm For 105°C



Rated Working Voltage 6.3 – 50 V.DC



I ≤ 0.01CV or 3 (uA) maxWhichever is greater after 2 minutes

I : Leakage Current(uA) C : Rated Capacitance(μF) V : Rated Voltage(V)


WV 6.3 10 16 25 35 50

SV 8 13 20 32 44 63


WV 6.3 10 16 25 35 50

tanδ 0.24 0.20 0.17 0.15 0.12 0.10



Rated Voltage (V) 6.3 10 16 25 35 50

-25°C / +25°C 3 2 2 2 2 2

-40°C / +25°C 6 5 4 3 3 3

Load Life

After 1000 hours application of W V at + 105°C the capacitor shall meet the following limits




Shelf Life





DIMENSIONS (mm)

D 4 5 6.3 8

F 1.5 2.0 2.5 3.5

d 0.45 0.50 0.50 0.50

α 1.0 1.3 1.3 1.5

L + α(max)

MIMISeriesM I



µFWV 6.3 / 0J 10 / 1A 16 / 1C

ITEM D×L R.C. D×L R.C. D×L R.C.

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

10 → 4x7 29

22 4x7 344x7 34 4x7 32

5x7 38 5x7 42

334x7 34 4x7 38 5x7 44

5x7 42 5x7 47 6.3x7 60

474x7 34 4x7 38

5x7 605x7 50 5x7 47

68 6.3x7 65

1004x7

50 5x7 70 6.3x7 705x7

150 6.3x7 85 6.3x7 85

220 6.3x7 776.3x7

876.3x7 97

8x7 8x9 140

330 6.3x7 80 8x7 110 8x7 120

470 8x7 120 8x9 190

µFWV 25 / 1E 35 / 1V 50 / 1H 63 / 1J

ITEM D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.1 → 4x7 1

0.22 → 4x7 2.3

0.33 → 4x7 3.5

0.47 → 4x7 5

1.0 → 4x7 10 6.3x7 55

2.2 → 4x7 19

3.3 → 4x7 24

4.7 → 4x7 244x7 25

5x7 29

10 4x7 294x7 30 5x7 40

5x7 36 6.3x7 44

22 5x7 365x7 39

6.3x7 656.3x7 60

335x7 43 5x7 45 6.3x7 64

6.3x7 51 6.3x7 72 8x7 75

475x7

65 6.3x7 70 8x7 856.3x7

1006.3x7

1258x9

220 8x9 140

M I


23

FEATURES Non-Polarized Hight 7mm For 85°C






I ≤ 0.05CV or 10 (µA) max Whichever is greater after 2 minutes

I : Leakage Current(µA) C : Rated Capacitance(µF) V : Rated Voltage(V)


W.V. 6.3 10 16 25 35 50S.V. 8 13 20 32 44 63


W.V. 6.3 10 16 25 35 50tanδ 0.24 0.20 0.17 0.15 0.12 0.12


Impedance ratio at 120HzRated Voltage (V) 6.3 10 16 25 35 50

-25°C / +25°C 4 3 2 2 2 2-40°C / +25°C 10 8 6 4 3 3

Load Life

After 1000 hours application of WV at +85°C the capacitor shall meet the following limits. (The polarity needs to exchange every 250 hours)

Capacitance Change ≤ ±25% of initial value Dissipation Factor ≤ 150% of initial specified value Leakage Current ≤ initial specified value

Shelf Life

After 500 hours application of WV at + 85°C the capacitor shall meet the following limits. Capacitance Change ≤ ±25% of initial value Dissipation Factor ≤ 200% of initial specified value Leakage Current ≤ initial specified value

DIMENSIONS (mm)D 4 5 6.3

F 1.5 2.0 2.5

d 0.45 0.50 0.50


µFWV 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H

ITEM D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.1 → 4x7 3

0.22 → 4x7 4

0.33 → 4x7 5

0.47 → 4x7 6

1.0 → 4x7 9

2.2 → 4x7 14 5x7 16

3.3 → 4x7 15 5x7 19 5x7 19

4.7 → 4x7 17 5x7 20 5x7 23 6.3x7 26

10 → 4x7 23 5x7 28 6.3x7 34 6.3x7 38 8x7 44

22 5x7 35 5x7 38 6.3x7 47 6.3x7 50 8x7 65 8x7 65

33 5x7 43 6.3x7 55 6.3x7 60 8x7 70 8x7 80

47 6.3x7 60 6.3x7 65 6.3x7 70 8x7 85

100 8x7 100 8x7 110 8x7 120


L + 2(max)

MNMNSeriesMN


24 MLMLSeries FEATURES

Low Leakage For Smaller Size



Rated Working Voltage 6.3 ~ 50 V.DC



I ≤ 0.02CV or 0.4 (μA) maxWhichever is greater after 2 minutes



WV 6.3 10 16 25 35 50

SV 8 13 20 32 44 63


WV 6.3 10 16 25 35 50

tanδ 0.22 0.19 0.16 0.14 0.12 0.10

When rated capacitance is over 1000µF, tanδ shall be added 0.02 to the listed value with increase of every 1000µF.



Rated Voltage (V) 6.3 10 16 25 35 50

-25°C / +25°C 4 3 2 2 2 2

-40°C / +25°C 8 6 4 4 3 3

Load Life





Shelf Life





DIMENSIONS (mm)

D 4 5 6.3 8

F 1.5 2.0 2.5 3.5

d 0.45 0.50 0.50 0.50

α 1.5 1.5 1.5 1.5

L + α(max)

ML


MULTIPLIER FOR RIPPLE CURRENTFrequency (Hz) 60(50) 125 500 1k 100k

Coefficient

0.1~1µF 0.50 1.00 1.20 1.30 1.50

2.2~4.7µF 0.65 1.00 1.20 1.30 1.50

10~47µF 0.80 1.00 1.20 1.30 1.50

100~1000µF 0.80 1.00 1.10 1.15 1.20

2200µF 0.80 1.00 1.05 1.10 1.15


µF

WV 6.3(0J) 10(1A) 16(1C) 25(1E) 35(1V) 50(1H)

ITEM Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

0.1 4x7 1.0

022 4x7 2.3

033 4x7 3.5

047 4x7 5.0

1 4x7 10

2.2 4x7 16

3.3 4x7 19

4.7 4x7 21 4x7 22 5x7 29

10 4x7 28 5x7 33 5x7 32 6.3x7 44

22 4x7 34 5x7 38 5x7 44 6.3x7 55 6.3x7 60 8x7 65

33 5x7 42 5x7 47 6.3x7 62 6.3x7 65 8x7 73

47 5x7 50 6.3x7 66 6.3x7 73 8x7 80

100 6.3x7 87 8x7 99 8x7 110

220 8x7 133

ML


26

FEATURES General Used Standard Size


Operation Temperature Range -40 to + 85°C -25 to + 85°C

Rated Working Voltage 6.3 - 100 V.DC 160 - 450 V.DC



I ≤ 0.01CV or 4 (μA) I ≤ 0.03CV + 40 (μA) max

Whichever is greater after 3 minutes I : Leakage Current(μA) C : Rated Capacitance(μF) V : Rated Voltage(V)


WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

SV 8 13 20 32 44 63 79 125 200 250 300 400 450 500


Add 0.02 per 1000μF for more than 1000μF

WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.10 0.08 0.15 0.20 0.20 0.25 0.25 0.25



Rated Voltage (V) 6.3 10 16 25 35-100 160-250 350-450

-25°C / +25°C 4 3 2 2 2 8 12

-40°C / +25°C 8 6 4 3 3

Load Life





Shelf Life




Leakage Current ≤ 200% of initial specified value

RIPPLE CURRENT FOR FREQUENCY MULTIPLIERSFrequency (Hz) 60 120 1K ≥ 10K

CAP(μF) Multiplier

6.3-25V 0.85 1.00 1.10 1.20

35-100V 0.80 1.00 1.15 1.25

CASE SIZE OF RADIAL TYPE

D 5 6.3 8 10 13 16 18 22 25

F 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0 12.5

d 0.5 0.5 0.5 0.6 0.6 0.8 0.8 0.8 0.8

RGRG Series

L + 2(max)

Vent (except Ø5 & Ø6.3)

RG



WV

µF

6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H 63 / 1J

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

0.1 5x11 1

0.22 5x11 2

0.33 5x11 3

0.47 5x11 5 5x11 5

1.0 5x11 10 5x11 10

2.2 5x11 23 5x11 29

3.3 5x11 35 5x11 40

4.7 5x11 20 5x11 25 5x11 30 5x11 35 5x11 40 5x11 45

10 5x11 35 5x11 40 5x11 50 5x11 60 5x11 65 5x11 70

22 5x11 35 5x11 55 5x11 75 5x11 90 5x11 95 5x11 100 6.3x11 115

33 5x11 55 5x11 80 5x11 110 5x11 115 5x11 120 6.3x11 125 6.3x11 8x11

130 140

47 5x11 75 5x11 95 5x11 130 5x11 135 5x11 6.3x11

120 140

6.3x11 8x11

140 150 8x11 190

100 5x11 130 5x11 180 5x11 6.3x11 185 6.3x11 200 8x11 230 8x11

10x12 230 250 10x12 300

220 5x11 6.3x11

200 240 6.3x11 250 6.3x11

8x11 320 8x11 10x12

290 340

8x11 10x12

290 370

10x12 10x15

380 440

10x15 10x20

410 490

330 6.3x11 8x11

260 300 8x11 330 8x11 360 8x15

10x12 380 420

10x12 10x15

420 490

10x15 10x20

490 580

10x20 13x21

540 680

470 6.3x11 8x11

330 380 8x11 400 8x11

10x12 400 470

10x12 10x15

460 540

10x20 13x21

510 640

10x20 13x21

610 760 13x25 880

1000 8x11 10x12

460 580

10x12 10x15

580 630

10x15 10x20

630 790

10x20 13x21

760 950

13x21 13x25

950 1100

13x25 16x26

1100 1350

16x26 16x32

1310 1550

2200 10x20 13x21

840 1050

10x2013x21

880 1100

13x21 13x25

1100 1350

13x25 16x26

1300 1550

16x26 16x32

1600 1800

16x36 18x36

1850 2090 18x42 2200

3300 10x20 13x21

1000 1250

13x21 13x25

1250 1400

13x25 16x26

1400 1700

16x26 16x32

1660 1950

16x36 18x36

1970 2220

18x36 18x42

2170 2400 22x42 2500

4700 13x21 16x26

1300 1700

13x25 16x26

1500 1800

16x26 16x32

1800 2100

16x32 18x36

1950 2360 18x36 2400 22x35 2500

6800 16x26 1900 16x26 16x32

1900 2150

16x36 18x36

2200 2500 18x36 2550 22x42 2600

10000 16x26 16x32

1900 2250

16x36 18x36 2500 18x36 2700 22x42 2800

15000 16x36 18x36

2500 2880 18x36 2950 22x42 3150 22x42 3200

22000 18x42 3650 22x42 3700 22x42 3800

RG


WV

µF

100 / 2A 160 / 2C 200 / 2D 250 / 2E 350 / 2V 400 / 2G 450 / 2W

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

0.47 5x11 10 5x11 12 5x11 14 5x11 14 5x11 14 6.3x11 14 6.3x11 14

1.0 5x11 21 5x11 17 5x11 19 6.3x11 19 6.3x11 19 6.3x11 19 8x11 19

2.2 5x11 30 6.3x11 26 6.3x11 8x11

22 27

6.3x11 8x11

24 30 8x11 33 8x11

10x12 26 33 10x12 33

3.3 5x11 45 6.3x11 8x11

30 35

6.3x11 8x11

30 37

8x11 10x12

30 38

8x11 10x12

33 39 10x12 40 10x15 42

4.7 5x11 50 6.3x11 8x11

32 40

8x11 10x12

36 45

8x11 10x12

36 45

10x12 10x15

39 45 10x15 45 10x15 50

10 6.3x11 75 8x11 10x12

50 65

10x12 10x15

57 70 10x15 70 10x15 70 10x20

13x21 56 70

13x21 13x25

60 75

22 8x11 130 10x15 110 10x15 120 10x20 130 13x21 130 13x25 16x26

110 130 16x26 130

33 8x11 10x12

140 170 10x20 150 10x20 160 13x21

13x25 140 160 13x25 170 16x26 170 16x32

16x36 160 180

47 10x12 10x15

190 230 13x21 180 13x21

13x25 160 190 13x25 210 16x26 220 16x26

16x32 180 220

18x36 18x42

200 230

100 10x20 400 13x25 16x26

250 300 16x26 330 16x32 310 18x36 360 18x36 360 22x42 370

220 13x25 710 16x32 16x36

450 510

18x32 18x36 600 18x42 600

330 13x25 16x26

720 860

18x36 18x42

540 600

18x36 18x42 800

470 16x26 1100 22x42 900 18x42 1000

1000 18x42 1350

2200 22x42 2300

RG


29

FEATURES General Used Standard Size


Operation Temperature Range -40 to + 105°C -25 to + 105°C

Rated Working Voltage 6.3 - 100 V.DC 160 – 450 V.DC



Rated voltage ≤100V >100V

Time After 2 minutes After 5 minutes

Leakage Current I=0.01CV or 3(μA)Whichever is greater

CV ≤ 1000I = 0.03CV+15(μA)

CV > 1000I = 0.02CV+25(μA)

C = Rated Capacitance (μF) V =Rated Voltage (V)


WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

SV 8 13 20 32 44 63 79 125 200 250 300 400 450 500


WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

tanδ 0.24 0.20 0.17 0.15 0.12 0.10 0.10 0.08 0.20 0.20 0.20 0.25 0.25 0.25



Rated Voltage (V) 6.3 10 16 25 35-100 160-250 350-450

-25°C/ +25°C 4 3 2 2 2 8 12

-40°C/ +25°C 10 8 6 4 3

Endurance(Load Life)




Leakage Current ≤ 200% specified value

Shelf Life





RIPPLE CURRENT FOR FREQUENCY MULTIPLIERSFrequency (Hz)

CAP(μF)50 120 300 1K 10K

0.1-47 0.75 1.00 1.35 1.57 2.00

100-470 0.80 1.00 1.23 1.34 1.50

1000-15000 0.85 1.00 1.10 1.13 1.15

0.47-220 0.80 1.00 1.25 1.40 1.60

330 0.90 1.00 1.10 1.13 1.15

DIMENSIONS (mm)

D 5 6.3 8 10 13 16 18 22 25

F 2.0 2.5 3.5 5.0 7.5 10 12

d 0.5 0.6 0.8 0.8

α 1.5 2.0 L + α(max)


RBRB SeriesRB


CASE SIZE & MAX RIPPLE CURRENTWV

µF

6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H 63 / 1J

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

0.47 5x11 7 5x11 8

1.0 5x11 12 5x11 13

2.2 5x11 18 5x11 20

3.3 5x11 25 5x11 27

4.7 5x11 20 5x11 25 5x11 30 5x11 34

6.8 5x11 25 5x11 30 5x11 32 5x11 37

10 5x11 25 5x11 30 5x11 40 5x11 50 5x11 55

15 5x11 40 5x11 45 5x11 50 5x11 60 5x11 65

22 5x11 45 5x11 55 5x11 60 5x11 65 5x11 75 6.3x11 90

33 5x11 60 5x11 70 5x11

75 5x11 85 6.3x11 105 6.3x11 110

6.3x11 8x11 120

47 5x11 60 5x11 75 5x11 85 5x11 90 5x11 95 6.3x11 100

8x11 155 6.3x11 115 8x11 125

56 5x11

68 5x11 75 5x11 80 5x11 100 6.3x11 125 8x11 130 8x11 159 10x12 198

100 5x11 100 5x11 110

5x11 110 6.3x11 145 6.3x11 1506.3x11

160 8x14 230

8x11

6.3x11 135 8x11 180 8x11 190 210 10x12 26010x12

120 6.3x11

150 5x11 120 6.3x11 130 8x11 180 8x11 200 10x12 240 10x12 289 10x15 330

220 4x11

140 6.3x11 180 6.3x11 180 8x11 200 8x14 280

10x15 40010x15 400

6.3x11 8x11 235 10x12 250 10x12 315 10x20 450

330

6.3x11 160 6.3x11

255 8x11 285

8x11320 10x12 380 10x15 450

13x21 650 8x15

8x11 200 8x11 355 10x15 440 10x20 53510x12

470

6.3x11 220 6.3x11 2408x11

3108x14

40010x15

490 10x20

730

13x21 7008x12 10x12 10x15

8x11 280 8x11 305 10x12 39510x15

470 13x21 580 13x21 13x25 80010x20

560 10x12

680 10x12 320 8x11

420 10x15 530 10x20 650 13x21 730 13x25 860 13x25 840

10x12 16x26 1000

1000

8x11370

8x14490

10x12590

13x16680

13x16850 13x25 930 16x26 1020

8x12 10x12 10x15 13x20 13x21

10x12 470 10x15 570 10x20 700 13x21 855 13x25 995 16x26 1110 16x32 1200

1500 10x15 600 10x20 750 10x20 680

13x25 1020 16x26 1110 16x32 1350 16x32 1300

13x21 860 16x36 1450

2200

10x20 740 10x20 800 13x21 990 13x25 1030 13x21 1230 16x36 1360

13x21 930 13x21 1010 13x25 115016x15

123016x26

145016x32

153016x26 13x21 18x36

3300 10x20 880 13x21 1050 13x25 1140 16x26 1230 16x36 1470

18x42 1700 13x21 1100 13x25 1220 16x26 1350 16x32 1450 18x36 1660

3900 10x25

4700

13x25 1100 13x25 1190 16x26 1330

16x261380

18x36 1580

22x35 1900

16x32142016x36

16x26 1320 16x26 1410 16x32 15601570

18x42 175018x32

169018x36

6800 13x25 1300 16x26 1370 16x36 1590

18x36 1850 16x26 1350 16x32 1600 18x36 1790

10000 16x26 1560 16x36 1760

18x36 2100 16x32 1830 18x36 1980

15000 18x36 2280

RB


WV

µF

100 / 2A 160 / 2C 200 / 2D 250 / 2E 350 / 2V 400 / 2G 450 / 2W

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

Case Size(mm)

Ripple Current

(mA)

0.47 5x11 10 5x11 12 5x11 14 5x11 14 5x11 14 6.3x11 14 6.3x11 14

1.0 5x11 15 5x11 17 5x11 19 6.3x11 19 6.3x11 20 6.3x11 16

8 x11 20 8x11 20

2.2 5x11 22 6.3x11 25 6.3x11 22 6.3x11 23

8x11 358x11 28

10x12 35 8x11 28 8x11 29 10x12 35

3.3 5x11 29 6.3x11 30 6.3x11 32 8x11 33 8x11 37 8x11 38

10x15 548x11 36 8x11 40 10x12 42 10x12 47 10x12 50

4.7 5x11 376.3x11 34 8x11 40 8x11 41 10x12 47 10x12 49

10x15 60 8x11 43 10x12 50 10x12 52 10x15 55 10x15 57

6.8 5x11 46 10x12 54 10x12 60 8x15 62

10x15 65 10x20 72 10x20 80 10x12 60

105x11 55 8x11 56 10x12 69

10x15 88 10x15 95 10x20 77 13x21 85

6.3x11 65 10x12 70 10x15 80 13x21 97 13x25 100

15 8x11 82 10x1S 90 10x15 110 10x15 120 10x20 140 10x20 100

16x26 160 13x25 150

226.3x11

115 10x15 130 10x15 140 10x20 155 13x21 165 13x21 150 16x26 150

8x11 13x25 175 16x32 180

338x11 120

10x20 180 10x20 190 13x21 170

13x25 220 13x25 190 16x26 190

10x12 160 13x25 200 16x26 230 16x36 240

4710x12 180

13x21 270 13x21 240 13x21

330 16x26 340 16x26 280 16x36 300

10x15 210 13x25 290 13x25 16x36 350 18x42 360

68 10x15 241 13x25 300 13x25 330 16x26 350 16x32 370 16x32

380 22x42 400 18x36

10010x16 250 13x25 330

16x26 410 16x32 430 18x36 460 18x36 480 10x20 385 16x26 400

150 13x25 414 16x32 435 16x36 450 18x42 460 22x42 480

220 13x25 590 16x32 550 18x36 580

22x42 680 16x36 620 18x42 650

33013x25 600 18x36 770 18x42 780

16x26 720 18x42 850 22x42 920

47016x26 740

22x42 980 16x23 875

680 16x36 1200

1000 18x42 1340

22x42 1500

RB


32

FEATURES 105°C Standard size: For low leakage current Load life: 105°C 1000 hours


Operation Temperature Range -40 ~ +105°C


Capacitance Tolerance (120Hz 20°C) ±20% (M)

Leakage Current(Max) at 20°C

I ≤ 0.002CV or 0.4 (μA) After2 minutes



WV 6.3 10 16 25 35 50

SV 8 13 20 32 44 63


Rated Voltage (V) 6.3 10 16 25 35 50

tanδ 0.24 0.19 0.16 0.14 0.12 0.10



Rated Vdtage(V) 6.3 10 16 25 35 50

Z-25°C /Z+20°C 4 3 2 2 2 2

Z-40°C /Z+20°C 8 6 4 4 3 3


Test conditions- Duration time : l000Hrs, Ambient temperature : +105°C Applied voltage : Rated DC working voltage

capacitance change Within ±20% of the initial value.

Dissipation Factor Not more than 200% of the specified value.

Leakage Current Not more than the specified value.

Shelf LifeThe following specification shall be satisfied when the capacitors are stored to 20°C after exposing them for 1000 hours at 105°C without voltage applied. The capacitors meet the specified value for load life characteristics listed above.


CAP(μF) 60(50) 120 500 1K 10K≤

0.1 ~ 47μF 0.80 1.00 1.20 1.30 1.50

100 ~ 1000μF 0.80 1.00 1.10 1.15 1.20

DIMENSIONS (mm)

D 5 6.3 8 10

F 2.0 2.5 3.5 5.0

d 0.5 0.5 0.5 0.6

α 1.0(L≤20)

L + α(max)

LLLLSeriesLL



µF 6.3V / 0J 10V / 13 16V / 20 25V / 32 35V / 44 50V / 63

Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

0.1 5x11 1

0.22 5x11 2

0.33 5x11 3

0.47 5x11 5

1 5x11 10

2.2 5x11 20

3.3 5x11 30

4.7 5x11 25 5x11 30 5x11 35

10 5x11 30 5x11 45 5x11 50 5x11 55

22 5x11 40 5x11 45 5x11 60 5x11 80 5x11 85 6.3x11 90

33 5x11 50 5x11 65 5x11 80 5x11 90 6.3x11 110 6.3x11 120

47 5x11 70 5x11 80 5x11 90 6.3x11 120 6.3x11 130 8x12 170

100 5x11 90 6.3x11 130 6.3x11 160 8x12 200 8x12 230 10x12 280

220 6.3x11 200 8x12 270 8x12 280 10x12 350 10x16 400 10x20 460

330 8x12 300 8x12 350 10x12 380 10x16 460 10x20 520

470 8x12 360 10x12 450 10x16 500 10x20 590

680 10x16 470 10x20 570

1000 10x16 640 10x20 730

LL


34

FEATURES 85°C Standard size: For low leakage current Load life: 85°C 1000 hours


Operation Temperature Range -40 to + 85°C

Rated Working Voltage 6.3 - 100 V.DC






WV 6.3 10 16 25 35 50 63 100

SV 8 13 20 32 44 63 79 125


WV 6.3 10 16 25 35 50 63 100

tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08



Rated Voltage (V) 6.3 10 16 25 35 50 63 100

-25°C / +25°C 4 3 2 2 2 2 2 2

-40°C / +25°C 8 6 4 4 3 3 3 3

Load Life





Shelf Life The following specification shall be satisfied when the capacitors are stored to 20°C after exposing them for 1000 hours at 85°C without voltage applied. The capacitors meet the specified value for load life characteristics listed above.


CAP(μF) 60(50) 120 500 1K 10K≤

0.1 ~ 47μF 0.80 1.00 1.20 1.30 1.50

100 ~ 1000μF 0.80 1.00 1.10 1.15 1.20

DIMENSIONS (mm)

D 5 6.3 8 10 13 16 18

F 2.0 2.5 3.5 5.0 7.5

d 0.5 0.6 0.8

α 1.0 2.0 L + α(max)


LGLGSeriesLG



µF

WV 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H 63 / 1J 100 / 2A

ITEM Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

01 5x11 1 5x11 2

0.22 5x11 2 5x11 4

0.33 5x11 3 5x11 7

0.47 5x11 5 5x11 10

1 5x11 10 5x11 18

2.2 5x11 20 5x11 25

3.3 5x11 35 5x11 45

4.7 5x11 30 5x11 35 5x11 40 5x11 50

10 5x11 40 5x11 50 5x11 55 5x11 60 6.3x11 75 8x12 90

22 5x11 45 5x11 50 5x11 70 5x11 85 5x11 90 6.3x11 100 8x12 110 10x12 130

33 5x11 55 5x11 70 5x11 90 5x11 100 6.3x11 120 6.3x11 130 8x12 160 10x16 180

47 5x11 75 5x11 90 5x11 110 6.3x11 130 6.3x11 140 8x12 180 10x12 200 10x20 220

100 5x11 100 6.3x11 140 6.3x11 180 8x12 210 8x12 240 10x12 290 10x20 330 13x21 370

220 6.3x11 220 8x12 280 8x12 300 10x12 360 10x16 410 10x20 480 13x21 540 16x26 580

330 8x12 310 8x12 360 10x12 400 10x16 470 10x20 530 13x21 600 13x26 700 16x32 730

470 8x12 380 10x12 460 10x16 520 10x20 600 13x21 670 16x26 750 16x26 840 18x36 910

680 10x16 480 10x20 590 13x21 720 13x26 800 16x26 830 16x26 900 16x32 1050

1000 10x16 650 10x20 750 13x21 900 13x26 1000 16x26 1100 16x32 1140 18x36 1320

LG


36 NPNPSeries FEATURES

General Used Standard Size


OperationTemperature Range -40 to +105°C




I ≤ 0.03CV or3 (µA) maxAfter 3 minutes

I : Leakage Current( µA) C : Rated Capacitance( µF) V : Rated Voltage(V)


WV 6.3 10 16 25 35 50 63 100

SV 8 13 20 32 44 63 79 125

Dissipation Factor(120Hz 20°C)(tanδ)

Add 0.02 per 1000µF for more than 1000µF

WV 6.3 10 16 25 35 50 63 100

tanδ 0.26 0.24 0.22 0.20 0.16 0.14 0.12 0.10



Rated Voltage (V) 6.3 10 16 25 35 50 63 100

-25°C / +25°C 4 3 2 2 2 2 2 2

-40°C / +25°C 10 8 6 5 4 4 3 3

Load Life

After 1000 hours application of W V at +105°C the capacitor shall meet the following limits. The polarity needs to exchange every 250hours.




Shelf Life

At 105°C no voltage applied after 1000 hours and then through the aging treatment (reference JIS C-5102) the capacitor shall meet the following limits.




NP


DIMENSIONS (mm)D 5 6.3 8 10 13 16 18

F 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.5 0.6 0.6 0.8 0.8

α 1.5 2.0 2.0


µF

WV 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H 63 / 1J 100 / 2A

ITEM Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

0.1 ~ 0.47 5x11 11 5x11 14

1 5x11 17 5x11 21

2.2 5x11 25 6.3x11 34

3.3 5x11 27 5x11 28 6.3x11 39

4.7 5x11 34 5x11 34 5x11 34 6.3x11 34 6.3x11 47

10 5x11 42 5x11 42 511 43 6.3x11 52 6.3x11 57 8x11 71

22 5x11 57 5x11 57 6.3x11 65 6.3x11 73 8x11 89 8x11 95 10x16 135

33 5x11 64 5x11 64 5x11 70 6.3x11 80 8x11 100 8x11 105 10 x12 135 13x21 220

47 5x11 76 5x11 76 6.3x11 95 6.3x11 95 8x11 120 10x12 150 10x16 180 13x21 240

100 6.3x11 125 6.3x11 125 8x11 160 8x11 160 10x16 230 10x20 265 13x21 320 16x26 425

220 8x11 215 8x11 215 10x12 275 10x16 305 13x21 410 13x26 480 16x26 575 18x36 720

330 8x11 265 10x12 345 10x16 375 13x21 450 13x21 505 16x26 650 16 x31 655

470 10x12 370 10x16 410 10x20 485 13x21 540 13x25 655 16x32 835 18x36 965

1000 10x20 650 13x21 720 13x25 855 16x32 950 16x32 1140

2200 13x25 1160 16x26 1280 16x32 1510 18x36 1620

3300 16x26 1570 16x32 1690 18x36 1980

4700 16x32 2020 18x36 2160

6800 18x36 2600

L + α(max)

NP


38 NGNGSeries FEATURES

Non-Polarized 85ºC


Operation Temperature Range -40° ~ +85°C -25º ~ +85ºC

Rated Working Voltage 10 ~ 100V.DC 160 ~ 250V.DC



I ≤ 0.03CV or 3 (µA) After 1 minutewhichever s greater measured with rated working

votage applied.



WV 10 16 25 35 50 63 100 160 200 250

SV 13 20 32 44 63 79 125 200 250 300

Dissipation Factor(120Hz 20°C)

Rated Voltage (V) 10 16 25 35 50 63 100 160 200 250

tanδ 25 20 15 15 13 10 10 15 15 20


Impedance ratio max.

Rated Voltage (V) 10 16 25 35 50 63 100 160 200 250

-25°C / +25°C 3 2 2 2 2 2 2 2 2 3

-40°C / +20°C 6 4 3 3 3 3 3


Test conditions Duration time : l000Hrs Ambient temperature : +85°CApplied voltage : Rated DC working voltage

After test requirements at +20°CCapacitance change : ≤±20% of the initial measured valueDissipation factor : ≤150% of the initial specified valueLeakage current : ≤The initial specified value

DIMENSIONS (mm)

D 5 6.3 8 10 13 16

F 2.0 2.5 3.5 5.0 5.0 7.5

d 0.5 0.5 0.5 0.6 0.6 0.8

α 1.5 1.5 1.5 2.0 2.0 2.0

MULTIPLIER FOR RIPPLE CURRENTFrequency(Hz) 50(60) 120 400 1k 10k 100k≤

Mutiplier

5.6 ~ 33µF 0.8 1 1 .30 1.45 1.65 1.70

39 ~ 270µF 0.8 1 1.23 1.36 1.48 1.53

330 ~ 680µF 0.8 1 1.16 1.25 1.35 1.38

L + α(max)


NG



µFWV 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H

ITEM Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

0.47 5x11 11

1 5x11 17

2.2 5x11 25

3.3 5x11 27

4.1 5x11 34

10 5x11 34 5x11 43 6.3x11 52

22 5x11 57 6.3x11 65 6.3x11 73 8x11 89

33 5X11 64 6.3x11 70 6.3x11 80 8x11 100 10x12 105

47 5X11 76 6.3x11 95 6.3x11 95 8x11 120 10x12 150

100 6.3X11 125 8x11 160 8x11 160 10x12 230 10x20 265

220 8x11 215 10x12 275 10x12 305 10x20 410 13x25 480

330 10x12 345 10x12 375 10x16 450 13x20 505 16x25 650

470 10x12 410 10x16 485 13x20 540 13x25 655

1000 10x20 720 13x20 855

µFWV 63 / 1J 100 / 2A 160 / 2C 200 / 2D 250 / 2E

ITEM Size R.C. Size R.C. Size R.C. Size R.C. Size R.C.

0.47 5x11 12 5x11 14 5x11 17 6.3x11 21 6.3x11 28

1 5x11 18 5x11 21 6.3x11 25 8x11 28 8x11 34

2.2 5x11 26 5x11 34 8x11 38 8x11 42 10x12 50

3.3 6.3x11 28 6.3x11 39 8x11 43 10x12 47 10x16 57

4.7 6.3x11 34 8x11 47 10x12 52 10x16 56 10x20 89

10 6.3x11 57 8x11 71 10x16 89 10x20 95 10x20 135

22 8x11 95 10xl6 135 10x20 150 13x20 180 13x25 220

33 10x12 135 10x20 220 13x20 230 13x25 265 16x25 320

47 10x16 180 13x20 240 13x25 265

100 13x20 320 16x25 425

220 13x25 575

All blank voltage on sleeve marking is the same voltage as “→”

NG


40 BPBP Series FEATURES

Bi-Polarized For Horizontal Deflection



Rated Working Voltage 25 – 50 V.DC

Capacitance Tolerance(120Hz 20°C) ±20% (M) ±10% (K)

Leakage Current(120Hz 20°C) 100 (mA) After 5 minutes in both directions.


WV 25 35 50

SV 32 44 63

Dissipation Factor(120Hz 20°C)(tanδ) tanδ ≤ 0.05

Load Life

After 2000 hours application WV at +85°C, the capacitor shall meet the following limits. (The polarity needs to exchange every 250 hours)




DIMENSIONS (mm)

D 10 13 16 18 22

F 5.0 7.5 10

d 0.6 0.8 0.8


µFWV 25 / 1E 35 / 1V 50 / 1H

ITEM D×L E.S.R. R.C. D×L E.S.R. R.C. D×L E.S.R. R.C.

2.2 10x20 30.14 2.8 13x26 30.14 3.5 13x26 30.14 3.5

3.3 13x26 20.10 4.5 13x26 20.10 4.8 16x26 20.10 4.8

4.7 13x26 14.11 5.5 13x26 14.11 6.5 16x32 14.11 6.5

6.8 16x26 9.75 7.5 16x26 9.75 8.0 16x36 9.75 8.0

8.2 16x32 8.09 8.5 16x32 8.09 9.5 18x36 8.09 9.5

10 18x32 6.63 10.0 18x32 6.63 10.5 18x36 6.63 10.5

12 18x32 5.53 11.5 18x32 5.53 12.0 22x41 5.53 12.0

18 18x32 3.68 13.0 18x32 3.68 13.0

22 18x32 2.83 14.5 18x32 2.83 14.5

L + 2(max)

Vent

BP


41

FEATURES Axial Type For 85°C


Operation Temperature Range -40 to + 85°C -25 to +85°C

Rated Working Voltage 6.3 - 100 V.DC 160 - 450 V.DC



I ≤ 0.03CV or 3µA Whichever is greater, after 3 minutes

I ≤ 0.01CV + 10, after 3 minutes

I : Leakage Current(µA) C : Rated Capacitance(µF) V : Rated Voltage(V)


WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

SV 8 13 20 32 44 63 79 125 200 250 300 400 450 500

Dissipation Factor(120Hz 20°C)(tanδ)

Add 0.02 per 1000μF for more than 1000μF

WV 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

Tanδ 0.24 0.20 0.16 0.14 0.12 0.10 0.10 0.10 0.20 0.20 0.20 0.24 0.24 0.24


Impedance ratio at 120HzRated Voltage 6.3 10 16-35 50-100 160-350 400-450-25°C / +25°C 4 3 2 2 3 4-40°C / +25°C 8 6 4 3

Load Life

After 1000 hours application of WV at+85°C the capacitor shall meet the following limits




Shelf Life

After 500 hours application of WV at+85°C the capacitor shall meet the following limits




DIMENSIONS (mm)

D 6.3 8 10 13 16 18 22 25

d 0.5 0.5 0.6 0.6 0.8 0.8 0.8 0.8

α 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0

RTRT Series

L + α(max) 30 min30 min

RT



µFWV 6.3 / 0J 10 / 1A 16 / 1C 25 / 1E 35 / 1V 50 / 1H 63 / 1J

ITEM D×L R.C D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.47 5x12 5

1.0 5x12 10

2.2 5x12 23

3.3 5x12 28 5x12 31

4.7 5x12 34 5x12 37

10 5x13 37 5x12 40 5x12 45 5x12 50 5x12 55

22 5x12 60 5x12 65 5x12 70 6.3x12 85 6.3x12 90

33 5x12 65 5x12 70 5x12 80 6.3x12 90 6.3x16 110 6.3x16 120

47 5x12 80 5x12 85 6.3x12 100 6.3x16 120 6.3x16 130 8x16 160

100 5x12 110 6.3x12 130 6.3x16 160 6.3x16 170 8x16 210 8x16 220 8x20 260

220 6.3x16 220 6.3x16 210 8x13 257 8x16 280 8x20 340 10x21 410 10x26 480

330 6.3x16 250 8x16 300 8x16 320 8x20 380 10x21 460 10x26 560 13x26 650

470 8x15 330 8x16 350 10x17 430 10x21 510 10x26 610 13x36 730 13x32 840

1000 10x21 600 10x21 640 10x26 770 13x26 900 13x32 1060 16x32 1260 16x32 1330

2200 13x26 1020 13x26 1090 16x28 1180 16x32 1480 16x32 1580 18x41 1920 22x40 2160

3300 13x26 1200 13x32 1390 16x32 1620 16x41 1710 16x41 2050 22x40 2340 22x52 2470

4700 16x32 1500 16x32 1730 16x41 1840 18x41 2170 22x40 2470 22x52 2650 25x61 2710

µFWV 100 / 2A 160 / 2C 200 / 2D 250 / 2E 350 / 2V 400 / 2G 450 / 2W

ITEM D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C. D×L R.C.

0.47 5x12 10

1.0 5x12 18 6.3x12 13 6.3x12 13 6.3x16 14 6.3x16 12 8x16 14 8x16 14

2.2 5x12 28 6.3x16 23 6.3x16 23 8x16 27 8x16 24 8x20 28 10x21 31

3.3 5x12 34 8x16 33 8x16 33 8x16 33 8x20 32 10x21 38 10x21 38

4.7 5x12 40 8x16 39 8x16 39 8x20 45 10x21 46 10x21 46 10x26 50

10 6.3x12 60 8x20 60 10x21 70 10x21 70 13x26 85 13x26 85 13x26 85

22 8x16 120 10x26 120 13x26 140 13x26 140 13x32 140 16x32 150 16x32 150

33 8x16 150 13x26 170 13x26 170 13x32 190 16x32 190 16x41 210 18x41 230

47 8x20 190 16x32 230 13x32 230 16x32 260 16x41 260 18x41 290 22x40 310

100 10x26 340 16x41 430 16x41 430 16x41 430 22x40 420 22x52 460 22x52 540

220 13x26 560 22x40 680 22x40 680 22x40 680

330 13x32 750 22x52 940 25x52 1010

470 16x32 970 25x52 1200

1000 22x40 1540

2200 25x61 2430

RT


43THTHSeries FEATURES

High Temperature For 125°C



Rated Working Voltage 10 - 63 V.DC






WV 10 16 25 35 50 63

SV 13 20 32 44 63 79


WV 10 16 25 35 50 63

tanδ 0.35 0.22 0.20 0.17 0.15 0.12



Rated Voltage (V) 10 16 25 35 ~ 63

-25°C / +25°C 8 6 4 3






DIMENSIONS (mm)

D 8 10 13

F 3.5 5.0 5.0

d 0.5 0.6 0.6

α 2.0

L + α(max)

Vent

TH



Rate Voltage 10(1A) 16(1C) 25(1E)

µF DXL R.C. DXL R.C. DXL R.C.

33 → 8X12 110

47 → 8X12 117 8X12 117

100 8X12 123 10X12 158 10X16 203

220 10X16 214 10X20 275 10X20 279

330 10X16 224 13X20 360 13X25 425

470 10X20 292 13X25 462

1000 13X20 474

Rate Voltage 35(1V) 50(1H) 63(1J)

µF DXL R.C. DXL R.C. DXL R.C.

0.47 → 8X12 5

1 → 8X12 10

2.2 → 8X12 23

3.3 → 8X12 35 8X12 44

4.7 → 8X12 50 8X12 66

10 → 10X12 121 10X12 121

22 8X12 101 8X12 87 8X12 87

33 10X12 138 10X12 138 10X16 169

47 10X12 149 10X16 188 10X20 218

100 10X20 268 13X20 311 13X25 379

All blank voltage on sleeve marking is the same voltage as “→”

Size øDXL(mm), Ripple Current (mA r.m.s./125˚C, 120Hz)TH


45RERESeries FEATURES

Low Impedance





Leakage Current(120Hz 20°C) I ≤ 0.01CV After 2 minutes



WV 6.3 10 16 25 35 50

SV 8 13 20 32 44 63


WV 6.3 10 16 25 35 50

tanδ 0.22 0.19 0.16 0.14 0.12 0.10

Load Life

After life test at conditions stated in the table below, the capacitors shall meet the following requirement.




Shelf Life

At 105°C no voltage applied after (ØD5mm~ØD6mm 500Hrs, ≤ ØD8mm 1000Hrs) the capacitor shall meet the following limits.

Capacitance Change ≤ 25% of initial value

tanδ ≤ 200% of initial specified value


RIPPLE CURRENT FOR FREQUENCY MULTIPLIERS

Frequency (Hz) 120 1K 10K 100K

Coefficient 0.4 0.7 0.85 1.0

DIMENSIONS (mm)

D 5 6.3 8 10 13 16 18

F 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.5 0.6 0.6 0.8 0.8

α 1.5 2.0

L + α(max)


Case Dia Life Time (hrs)

Ø D ≤ 8 2000

Ø D ≤ 10 3000

RE



µF6.3 / 0J 10 / 1A 16 / 1C

Case Size (mm) Ripple Current (mA) Impedance (Ω) Case Size (mm) Ripple Current

(mA) Impedance (Ω) Case Size (mm) Ripple Current (mA) Impedance (Ω)

47 5x11 180 0.750

100 5x11 180 0.7505x11 180 0.750

6.3x11 277 0.400

220 6.3x11 277 0.4006.3x11 277 0.400

8x11 479 0.170

270 6.3x11 277 0.400 8x11 479 0.170 8x12 539 0.140

3306.3x7

230 0.480 8x11 479 0.1708x11 479 0.170

6.3x11 8x14 634 0.110

470

6.3x11 277 0.4008x11 479 0.170

8x11 479 0.170

8x7 380 0.220 8x12 539 0.140

8x11 479 0.170 8x14 634 634 10x12 713 0.100

680 8x14 634 0.110 10x12 713 0.100 10x12 713 0.100

1000

8x11 479 0.17010x12 713 0.100 8x20 980 0.050

8x12 539 0.140

8x14 634 0.110 10x15 927 0.070 10x15 927 0.070

120010x12 713 0.100

10x20 1189 0.050 13x21 1585 0.03810x15 927 0.070

1500

8x14 927 0.070

10x20 1189 0.050 10x20 1189 0.0508x20 980 0.050

10x15 927 0.070

2200 10x25 1456 0.04010x25 1456 0.040 10x20 1189 0.050

13x21 1585 0.038 13x25 1917 0.030

3300 13x21 1585 0.038 13x25 1917 0.03013x36 2423 0.026

16x16 1940 0.042

4700 13x30 2149 0.028 13x36 2423 0.026 16x36 2742 0.025

6800 16x26 2239 0.028 16x36 2742 0.025

10000 16x36 2742 0.025

µF

25 / 1E 35 / 1V 50 / 1H 63 / 1J 100 / 2ACase Size (mm)

Ripple Current

(mA)

Impedance (Ω)

Case Size (mm)

Ripple Current

(mA)

Impedance (Ω)

Case Size (mm)

Ripple Current

(mA)

Impedance (Ω)

Case Size (mm)

Ripple Current

(mA)

Impedance (Ω)

Case Size (mm)

Ripple Current

(mA)

Impedance (Ω)

4.7 5x11 180 0.750 5x11 78 2.000

10 5x11 180 0.750 5x11 95 1.700 6.3x11 175 0.082

22 5x11 180 0.750 5x11 140 0.700 8x11 261 0.520

33 5x11 180 0.750 5x11 150 0.650

47 5x11 180 0.750 6.3x11 277 0.400 6.3x11 180 0.520 8x11 10x12

100 6.3x11 277 0.400 8x11 479 0.170 8x14 430 0.270 10x12

220

8x11 479 0.170

10x12 713 0.100 10x15 550 0.2008x14 713 0.100

10x12 634 0.110

330

8x14 634 0.110

10x20 1189 0.050 10x25 820 0.07210x11 684 0.130

10x15 927 0.070

470

8x14 634 0.11010x15 927 0.070

13x21 950 0.06510x12 713 0.100

10x15 927 0.07010x25 1456 0.040

10x20 1189 0.050

560 10x15

1000

10x16 927 0.07013x16 1030 0.065

16x26 1650 0.03913x16 1030 0.065

13x21 1585 0.038 13x25 1917 0.030

1200 13x25 1917 0.030 13x30 2149 0.028 16x32 2150 0.025

1500 13x30 2149 0.028 16x26 2239 0.028 16x36 2250 0.025

220013x25 1917 0.030

16x32 2547 0.02616X16 1940 0.042

3300 16x36 2742 0.025 18x36 2742 0.024

Size øDXL(mm), Ripple Current (mA r.m.s./105˚C, 100kHz)RE


47

FEATURES High Ripple Current




Capacitance Tolerance(120Hz 20°C) ±20% (120Hz)




WV 6.3 10 16 25 35 50 63 100

tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08

Load Life

After 1000 hours application of WV at +105°C the capacitors shall meet the following requirement. Other life test at conditions stated in the table below.



L ≥ 11 Ø D=6.8 2000

Dissipation Factor ≤ 200% of initial specified value L ≥ 16 Ø D=10 3000

Leakage Current ≤ initial specified value L ≥ 21 Ø D=13 4000

RIPPLE CURRENT FOR FREQUENCY MULTIPLIERS

Frequency (Hz)

CAP(μF)60 120 1K 10K 100K

6.8-33 0.45 0.55 0.75 0.90 1.00

39-330 0.60 0.70 0.85 0.95 1.00

390-1000 0.65 0.75 0.90 0.98 1.00

1200-18000 0.75 0.80 0.95 1.00 1.00

DIMENSIONS (mm)

D 5 6.3 8 10 13 16 18

d 0.5 0.5 0.6 0.8

F 2.0 2.5 3.5 5.0 7.5

α 1.5 2.0L + α(max)

Vent(except Ø5 & Ø6.3)

LZLZ SeriesLZ


CASE SIZE & MAX RIPPLE CURRENTRated voltage 6.3V / 0J

Cap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)150 5x11 210 0.580330 6.3x11 340 0.220470 6.3x11 350 0.240680 8x11 640 0.130820 10x12 865 0.0801000 8x12 / 8x12 840 0.087

12008x20 1050 0.06910x16 1210 0.060

1500 10x20 1400 0.0461800 13x16 1450 0.0492200 10x25 1650 0.042

270010x25 1910 0.03116x16 1940 0.042

3300 13x21 1900 0.0353900 13x25 2230 0.0274700 13x30 2650 0.0245600 13x35 2880 0.020

680013x40 3350 0.01716x26 2930 0.021

8200 16x32 3450 0.01710000 16x36 3610 0.015

Rated voltage 10V / 1ACap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

100 5x11 210 0.580220 6.3x7 / 6.3x11 245 / 340 0.400 / 0.220470 8x11 640 0.130

6808x14 840 0.08710x12 865 0.080

10008x20 / 10x12 1050 0.069

10x16 1210 0.0601200 10x20 1400 0.0461500 10x25 1650 0.042

220010x25 1910 0.03113x21 1900 0.035

2700 18x16 2210 0.0433300 13x25 2230 0.0273900 13x30 2650 0.0244700 13x35 2880 0.020

560013x40 3350 0.01716x26 2930 0.021

6800 16x32 3450 0.0178200 16x36 3610 0.015

Rated voltage 16V / 1CCap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

56 5x11 210 0.580100 6.3x11 340 0.220120 6.3x11 340 0.220220 6.3x11 340 0.220330 8x11 640 0.130

4708x12 / 8x14 596 / 840 0.110 / 0.087

10x12 865 0.080

6808x20 1050 0.069

10x16 1210 0.060

100010x20 1400 0.04613x16 1450 0.049

1200 10x25 1650 0.042

150010x25 1910 0.03113x21 1900 0.03516x16 1940 0.042

2200 13x25 2230 0.0272700 13x30 2650 0.0243300 13x35 2880 0.0203900 13x41 3350 0.017

470016x32 3450 0.01718x25 3140 0.019

5600 16x36 3610 0.0156800 16x42 4080 0.0138200 18x36 4220 0.014

Size øDXL(mm), Ripple Current (mA r.m.s./105˚C, 100kHz)LZ


Rated voltage 25V / 1ECap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

47 5x11 210 0.580100 6.3x11 340 0.220220 8x11 640 0.130

3308X14 840 0.08710x16 865 0.080

4708X20 1050 0.06910x15 1210 0.060

68010x20 1400 0.04613X16 1450 0.049

820 10x25 1650 0.042

100010x25 1910 0.03113X21 1900 0.035

1200 18x16 2210 0.0431500 10x25 / 13x25 1910 / 2230 0.031 / 0.0271800 13x30 2650 0.0242200 13x35 / 16x16 2880 0.0202700 13x41 3350 0.0173300 16x32 3450 0.0173900 16x36 3610 0.015

470016x42 4080 0.01318X36 4220 0.014

5600 18x42 4280 0.012

Rated voltage 35V / 1VCap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

33 5x11 210 0.58056 6.3x11 340 0.220

150 8x11 640 0.130

2208x14 840 0.08710x12 865 0.080

270 8x20 1050 0.069330 10x16 1210 0.060

47010x20 1400 0.04613x16 1450 0.049

560 10x25 1650 0.042

68010x25 1910 0.03113x21 1900 0.035

1000 13x16 / 13x25 2230 0.0271200 13x30 2650 0.0241500 13x35 2880 0.020

180013x41 3350 0.01716x26 2930 0.021

2200 16x32 3450 0.0172700 16x36 3610 0.0153300 16x42 4080 0.013

Rated voltage 50V / 1HCap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

22 5x11 180 0.7056 6.3x11 295 0.30

100 8x11 555 0.17120 8x14 730 0.12150 10x12 760 0.12180 8x20 910 0.091220 10x16 1050 0.084

27010x20 1220 0.06013x16 1260 0.061

330 10x25 1440 0.055

47010x25 1690 0.04313x21 1660 0.04516x16 1690 0.055

560 13x25 1950 0.034680 13x30 2310 0.030820 13x35 2510 0.025

100013x41 2920 0.02116x26 2555 0.025

1200 16x32 3010 0.0221500 16x36 3150 0.0191800 16x42 3710 0.016

LZ


Rated voltage 63V / 1J

Cap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

15 5x11 55 2.300

33 6.3x11 115 1.200

56 8x11 232 0.630

828x14 300 0.450

10x12 288 0.430

1208x20 362 0.330

10x16 357 0.310

18010x20 466 0.210

13x16 466 0.230

220 10x25 531 0.200

270

10x25 663 0.150

13x21 690 0.160

16x16 795 0.140

330 13x25 784 0.120

47013x30 905 0.100

16x21 1040 0.091

560 13x35 1050 0.083

680 13x41 1180 0.071

820 16x32 1570 0.054

1000 16x36 1790 0.045

1200 16x42 2020 0.040

Rated voltage 100V / 2A

Cap (µF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

6.8 5x11 55 2.300

15 6.3x11 115 1.200

27 8x11 232 0.630

39 8x14 300 0.450

47 10x12 288 0.430

56 8x20 362 0.330

8210x20 466 0.210

13x16 466 0.230

100 10x25 531 0.200

120 13x21 690 0.160

150 16x16 795 0.140

180 13x25 784 0.120

220 13x30 905 0.100

27013x35 1050 0.083

16x26 1250 0.073

330 13x41 1180 0.071

390 16x32 1570 0.054

470 16x36 1790 0.045

560 16x42 2020 0.040

LZ


51LELE Series FEATURES

Low ESR





Leakage Current (120Hz 20°C) I ≤ 0.01CV After 2 minutes


Surge Voltage (120Hz 20°C)WV 6.3 10 16 25 35 50 63 100

SV 8 13 20 32 44 63 79 125


WV 6.3 10 16 25 35 50 63 100

tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08

Load Life

After life test at conditions stated in the table below, the capacitors shall meet the following requirement.





Ø D=8 1000

Ø D=10 2000

Ø D=13 3000

Shelf Life After leaving capacitors under no load of 105°C for 1000 hours and applying voltage, they meet the specified value for load life characteristics listed above.

RIPPLE CURRENT FOR FREQUENCY MULTIPLIERSFrequency (Hz) 60(50) 120 1K 10K 100K

CAP(μF) Multiplier

6.8-33 0.45 0.55 0.75 0.90 1.00

69-330 0.60 0.70 0.85 0.95 1.00

390-1000 0.65 0.75 0.90 0.98 1.00

1200-18000 0.75 0.80 0.95 1.00 1.00

DIMENSIONS (mm)

D 5 6.3 8 10 13 16 18

F 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.5 0.6 0.6 0.8 0.8

α 1.5 2.0L + α(max)


LE


CASE SIZE & MAX RIPPLE CURRENTRated Voltage 6.3V / 0J

Cap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

39 4x7 130 0.85

68 5x7 210 0.43

1505x11 250 0.30

6.3x7 300 0.23

220 8x7 380 0.15

3306.3x11 405 0.130

8x9 380 0.150

560 8x11 760 0.072

680 6.3x11 740 0.065

8208x14 995 0.056

8x20 1250 0.041

1000

8x11 780 0.060

8x12 840 0.055

8x14 1000 0.050

8x20 1200 0.035

10x12 1030 0.053

12008x20 1250 0.041

10x16 1430 0.038

1500

8x20 1450 0.020

10x12 / 10x15 1030 / 1250 0.053 / 0.045

10x20 2000 0.020

220010x20 1750 0.025

10x25 2250 0.017

330010x25 2250 0.017

13x21 2360 0.021

3900 13x25 2770 0.018

4700 13x30 2650 0.018

560013x35 3400 0.015

16x21 3140 0.018

6800 16x26 3460 0.016

Rated Voltage 10V / 1ACap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

27 4x7 130 0.89

56 5x7 210 0.44

100 5x11 250 0.30

120 6.3x7 300 0.23

180 8x11 380 0.15

220 6.3x11 405 0.13

470 8x11 720 0.076

6808x14 950 0.060

10x12 1030 0.053

1000

8x14 940 0.042

8x20 1250 0.041

10x16 1430 0.038

1200 10x20 1820 0.023

1500 10x25 2150 0.022

2200 13x21 2360 0.021

330010x30 2360

0.01813x25 2770

390013x30 3290 0.016

16x21 3140 0.018

4700 13x35 3400 0.015

5600 16x26 3460 0.016

Size øDXL(mm), Ripple Current (mA r.m.s./105˚C, 100kHz)LE


Rated Voltage 16V / 1CCap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

18 4x7 130 0.9233 5x7 210 0.4556 5x11 250 0.3068 6.3x7 300 0.24

100 6x11 250 0.30

1206.3x11 405 0.138x11 380 0.15

220 6.3x11 340 0.220330 8x12 760 0.072

4708x12 / 8x14 760 / 995 0.072 / 0.056

10x12 1020 0.045

6808x20 1350 0.025

10x16 1430 0.038

10008x20 1400 0.02810x20 1820 0.023

1200 10x25 2150 0.022

1500

10x20 2250 0.02210x25 2550 0.01912x21 2360 0.02113x21 2360 0.021

220010x25 2150 0.02113x25 2770 0.019

3300 13x35 3400 0.0153900 16x26 3460 0.0166800 16x32

Rated voltage 25V / 1ECap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

15 4x7 130 0.9427 5x7 210 0.4647 5x11 250 0.3056 6.3x7 300 0.24

1006.3x11 405 0.13

8x7 380 0.15220 8x12 760 0.072

3308x16 995 0.05610x12 1030 0.053

4708x20 1250 0.041

10x16 1430 0.038680 10x20 1820 0.023820 10x25 2150 0.0221000 13x21 2360 0.0211500 13x25 2770 0.018

180013x31 3290 0.01616x21 3140 0.018

2200 13x35 3400 0.0152700 16x26 3460 0.016

Rated Voltage 35V / 1VCap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

10 4x7 130 0.9618 5x7 210 0.4733 5x11 250 0.3039 6.3x7 300 0.25

568x7 380 0.16

6.3x11 405 0.13150 8x11 760 0.072

2208x16 995 0.05610x12 1030 0.053

270 8x20 1250 0.041330 10x16 1430 0.038470 10x20 1820 0.023560 10x23 2150 0.022680 10x25 / 13x21 1570 / 2360 0.030 / 0.0211000 13x25 2770 0.018

120013x31 3290 0.01616x21 3140 0.018

1500 13x35 3400 0.0151800 16x26 3460 0.016

LE


Rated Voltage 50V / 1HCap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

5.6 4x7 130 1.010 5x7 210 0.50

225x11 238 0.346.3x7 300 0.26

33 8x11 380 0.1756 6.3x11 385 0.14

100 8x11 724 0.074120 8x16 950 0.061150 10x12 979 0.061180 8x20 1190 0.046220 10x16 1370 0.042270 10x20 1580 0.030330 10x25 1870 0.028470 13x21 2050 0.027560 13x26 2410 0.023680 13x31 2860 0.021

82013x35 2960 0.01916x21 2730 0.023

1000 16x26 3010 0.021

Rated Voltage 63V / 1JCap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

33 6.3x11 265 0.3556 8x11 500 0.22

828x14 665 0.16

10x12 685 0.15

1208x20 820 0.12

10x16 945 0.11

18010x20 1100 0.08013x16 1135 0.082

220 10x25 1300 0.073270 13x21 1495 0.060330 13x25 1850 0.043

47013x30 2250 0.03916x21 1990 0.045

56013x35 2450 0.03316x26 2550 0.032

68013x41 2780 0.02918x20 2450 0.038

82016x32 2810 0.02618x25 2780 0.031

100016x36 2835 0.02118x32 3270 0.025

120016x42 3340 0.01918x36 3310 0.020

1500 18x42 3420 0.018

Rated Voltage 100V / 2ACap (μF) Case Size (mm) Ripple Current (mA) Impedance 20°C 100kHz (Ω Max.)

6.8 5x11 125 1.4015 6.3x11 205 0.5727 8x11 355 0.3639 8x14 450 0.2547 10x12 450 0.2456 8x20 565 0.1968 10x16 580 0.18

8210x20 750

0.1313x16 735

100 10x25 880 0.12120 13x21 1045 0.094180 13x25 1195 0.071

22013x30 1410 0.06316x21 1295 0.071

27013x35 1560 0.05216x26 1600 0.053

330 13x40 1700 0.046390 16x32 1750 0.041

47016x36 1890 0.03318x32 1775 0.039

560 16x42 2080 0.030680 18x42 2570 0.028

LE


55

FEATURES High Ripple Current and Long Life



Rated Voltage Range 6.3 ~ 25V.DC


Leakage Current (25°C) I = 0.03CV, (After 2 minutes) I = Leakage Current (μA) C = Rated Capacitance (μF) V = Rated Voltage (V)

Surge Voltage (120Hz 20°C)

WV 6.3 10 16 25

SV 8 13 20 32

Dissipation Factor(25°C, 120Hz)

Rated Voltage (V) 6.3 10 16 25

tanδ 0.22 0.19 0.16 0.14

When rated capacitance is over 1000μF, tanδ shall be added 0.02 to the listed value with increase of every 1000μF.


After applying rate voltage with rated ripple current (Case size ≤ Ø8, 1500Hrs. ≥ Ø10, 2000Hrs.) at 105°C, 1000Hrs at 125°C the capacitors shall meet the following requirement.





Rated Voltage(V) 6.3 10 16 25

Z(-25°C) / Z (120Hz 20°C) 2 2 2 2

Z(-40°C) / Z (120Hz 20°C) 3 3 3 3

MULTIPLIER FOR RIPPLE CURRENT Frequency Coefficient

Frequency (Hz) 120 1K 10K 100K

Coefficient 0.50 0.80 0.90 1.00

DIMENSIONS(mm)D 8 10

F 3.5 5.0

d 0.5 0.6

α 1.5 2.0 L + α(max)


MEME SeriesME



Cap (µF) Case Size (mm)D×L Ripple Current (mA)

ESR (mΩMAX)

20°C, 100kHz

820 8x12 1140 36

10008x12 1010 40

8x14 1120 35

1200 8x16 1490 28

1500

8x20 1870 16

10x12 / 10x15 1540 26

10x20 2000 20

18008x20 1870 20

10x20 2000 20

220010x20

2550 1610x25

330010x25

2800 1410x30



ESR (mΩMAX)

20°C, 100kHz

680 8x14 1140 38

10008x20 1490 29

10x16 1540 26

15008x20 1870 20

10x20 2000 20

1800 10x20 2550 16

2200 10x25 2800 14

Rated voltage 16V / 1C

Cap (μF) Case Size (mm)D×L Ripple Current (mA)

ESR (mΩMAX)

20°C, 100kHz

4708x12 910 0.048

8x14 1140 37

6808x20 1490 29

10x15 1540 27

1000

8x20 1870 22

10x15 1386 0.028

10x20 2000 22

150010x20 1413 0.032

10x25 2550 18

1800 10x25 2800 14

220010x25 1645 0.028

13x25 2012 0.026

Rated voltage 25V / 1E


ESR (mΩMAX)

20°C, 100kHz

470 10x20 2000 22

Size øDXL(mm), Ripple Current (mA r.m.s./125˚C, 100kHz)ME


57

FEATURES 105°C Ultra Low ESR






I ≤ 0.03CV (After 2 minutes) I : Leakage Current(uA) C : Rated Capacitance(μF) V : Rated Voltage(V)


WV 6.3 10 16

SV 8 13 20


Rated Voltage (V) 6.3 10 16

tanδ 0.22 0.19 0.16

When rated capacitance is over 1000μF, tanδshall be added 0.02 to the listed value with increase of every 1000 μF.


After applying rated voltage with rated ripple current for 2000 Hrs at 105°C the capacitors shall meet the following requirements.





Rated Voltage (V) 6.3 10 16

Z(-25°C) / Z(+20°C) 2 2 2

Z(-40°C) / Z(+20°C) 3 3 3

MULTIPLIER FOR RIPPLE CURRENTFrequency 120 1k 10k 100k

Coefficient 0.5 0.80 0.90 1.00

Specifications subject to change without notice.

DIMENSIONS (mm)

D 8 10

F 3.5 5.0

d 0.5 0.6

α 1.5 2.0

L + α(max)

Vent

MZMZ SeriesMZ



µF DxL R.C. E.S.R.(100kHz mΩ)(Max)

820 8x11 1340 22

1200 8x16 1850 18

1500 10x16 2460 16

1800 8x20 2350 12

1800 10x16 2460 13

2200 10x20 2770 11

3300 10x25 3230 10

Rated Voltage 10V / 1A


680 8x12 1340 22

1000 8x16 1850 18

1000 10x15 1960 16

1500 8x20 2350 12

1500 10x16 2460 12.5

1800 10x20 2770 11

2200 10x25 3230 10

Rated Voltage 16V / 1C


470 8x12 1340 22

680 8x16 1850 18

680 10x15 1960 16

1000 8x20 2350 12

1000 10x16 2460 15

1500 10x20 2770 12

1800 10x25 3230 10

Size øDXL(mm), Ripple Current (mA r.m.s./105˚C, 100kHz)MZ


59

FEATURES Long Life, Low Impedance



Rated Working Voltage 6.3 ~35 V.DC



I ≤ 0.001CV or 3μA Whichever is greater.(After 2 minutes)



WV 6.3 10 16 25 35

SV 8 13 20 32 44


WV 6.3 10 16 25 35

tanδ 0.22 0.19 0.16 0.14 0.12

When rated capacitance is over 1000µF, tanδ shall be added 0.02 to the listed value with increase of every 1000µF.


Rated Voltage (V) 6.3 10 16 25 35

Z(-25°C) / Z(+25°C) 2 2 2 2 2

Z(-40°C) / Z(+25°C) 3 3 3 3 3


After life test with rated ripple current at conditions stated in the table below, the capacitors shall meet the following requirements.




DIMENSIONS (mm)D 5 6.3 8 10 13 16 18 22 25

F 2.0 2.5 3.5 5.0 7.5 10 12

d 0.5 0.6 0.8 0.8

α 1.5 2.0 2.0 2.0

MULTIPLIER FOR RIPPLE CURRENTFrequency 120 1k 10k 100k

Coefficient

47~270µF 0.50 0.73 0.92 1.00

330~680µF 0.55 0.77 0.94 1.00

820~1800µF 0.60 0.80 0.96 1.00

2200~8200µF 0.70 0.85 0.98 1.00

L + α(max)

Vent

ZHZH SeriesZH



µF DxL(mm) Ripple Current(mA) Impedance 25°C 100kHz(mΩ Max)

220 5x11 330 240

470 6.3x11 500 110

820 8x12 900 65

1200 8x16 1210 50

1200 10x12 1240 47

1500 8x20 1410 35

1800 10x16 1650 34

2200 10x20 1960 20

2700 10x23 2250 18

3900 13x21 2480 18

4700 13x25 2900 16

5600 13x30 3450 15

6800 16x20 3250 17

6800 13x36 3570 15

8200 16x25 3630 15



150 5x11 330 240

330 6.3x11 500 110

680 8x12 900 65

1000 8x16 1210 50

1000 10x12 1240 47

1500 8x20 1410 35

1500 10x16 1650 34

1800 10x20 1960 20

2200 10x23 2250 18

3300 13x21 2480 18

3900 13x25 2900 16

4700 13x30 3450 15

4700 16x20 3250 17

5600 13x36 3570 15

6800 16x25 3630 15

ZH


Rated voltage 16V / 1C


100 5x11 330 240

220 6.3x11 500 110

470 8x12 900 65

680 8x16 1210 50

680 10x12 1240 47

1000 8x20 1410 35

1000 10x16 1650 34

1500 10x20 1960 20

1800 10x23 2250 18

2200 13x21 2480 18

2700 13x25 2900 16

3300 13x30 3450 15

3300 16x20 3250 17

3900 13x36 3570 15

4700 16x25 3630 15

Rated voltage 25V / 1E


68 5x11 330 240

150 6.3x11 500 110

330 8x12 900 65

390 8x16 1210 50

470 10x12 1240 47

560 8x20 1410 35

680 10x16 1650 34

820 10x20 1960 20

1000 10x23 2250 18

1500 13x20 2480 18

1800 13x25 2900 16

2200 13x30 3450 15

2200 16x20 3250 17

2700 13x35 3570 15

3300 16x25 3630 15

Rated voltage 35V / 1V


47 5x11 330 240

100 6.3x11 500 110

220 8x11 900 65

270 8x16 1210 50

330 10x12 1240 47

390 8x20 1410 35

470 10x16 1650 34

560 10x20 1960 20

680 10x23 2250 18

1000 13x20 2480 18

1200 13x25 2900 16

1500 13x30 3450 15

1500 16x20 3250 17

1800 13x35 3570 15

2200 16x25 3630 15

ZH


62

FEATURES Low Impedance For Small Size








W V 6.3 10 16 25 35

tanδ 0.15 0.13 0.12 0.10 0.10

Load Life

After 1000 hours application of WV at +105°C the capacitors shall meet the following requirement. Other life test at conditions stated in the table below.

Capacitance Change ≤ ±25% of initial value Dissipation Factor ≤ 200% of initial specified value Leakage Current ≤ initial specified value


120 1K 10K 100K CAP(μF)

4.7~ 33 0.40 0.68 0.90 1.00

47~330 0.47 0.75 0.95 1.00

470~1000 0.55 0.85 0.98 1.00

DIMENSIONSD 4x7 5x7 6.3x7 6.3x11 8x11 10x12 10x16

F 1.5 2.0 2.5 3.5 5.0

d 0.45 0.50 0.60

α 1.0 1.5 2.0

L + α(max)

Vent (except Ø8 & Ø10)

LALA SeriesLA



Cap (μF) Case Size (mm) Ripple Current (mA) Impedance 25˚C (Ω Max)22 5x7 230 0.5233 5x7 350 0.4847 6.3x7 480 0.26100 6.3x11 640 0.15220 8x11 910 0.077330 8x11 1000 0.043470 8x11 1000 0.0431000 10x16 1650 0.025

Rated Voltage 10V / 1A

Cap (μF) Case Size (mm) Ripple Current (mA) Impedance 25˚C (Ω Max)

10 4x7 190 0.60

22 5x1 230 0.49

33 6.3x7 350 0.26

47 6.3x7 350 0.26

100 6.3x11 480 0.15

220 8x11 1000 0.044

3308x11

1000 0.04310x12

470 10x12 1300 0.035

Rated Voltage 16V / 1C


22 5x7 350 0.27

33 5x7 350 0.26

47 6.3x7 480 0.15

100 6.3x11 670 0.078

220 8x12 1000 0.044

330 10x12 1300 0.030

470 10x16 1740 0.025

Rated Voltage 25V / 1E


10 4x7 230 0.52

22 5x7 350 0.27

33 6.3x7 480 0.16

47 6.3x7 480 0.15

100 6.3x11 670 0.078

220 10x12 1300 0.031

330 10x16 1140 0.026

Rated Voltage 35V / 1V


4.7 4x7 230 0.64

10 5x7 350 0.33

22 6.3x7 480 0.17

33 6.3x7 480 0.16

47 6.3x11 670 0.089

100 8x12 1000 0.048

220 10x16 1740 0.026

Size øDXL(mm), Ripple Current (mA r.m.s./105˚C, 100kHz)LA

64

1. Series: Series is represented by a two digit code. If there are 2 digits only for series code, keep blank on the third digit.

2. Rated Voltage: Voltage on volts (V) is represented by two digit code showing the real working voltage.

3. Capacitance: Rated capacitance in μF is represented by a three digit number. The first two digits are the significant figures of the nominal capacitance and the third digit indicates the number of zeros following these figures. The decimal point is represent by the capital letter R. Please refer to the follow ing example:

μF 0.1 0.47 1 4.7 10 47 100 470 1000

Part number 0R1 R47 010 4R7 100 470 101 471 102

4. Tolerance: Symbol of W, T, Q, V, M, K and show special capacitance tolerance which are listed are follows:

W = -10% ~ +100% M = -20% ~ +20%

T = -10% ~ +50% K = -10% ~ +10%

Q = -10% ~ +30% J = -5% ~ +5%

v = -10% ~ +20%

5. Case Size: Symbol of case size are listed as follows:

Ø DxL (mm) Symbol Ø DxL (mm) Symbol Ø DxL (mm) Symbol Ø DxL (mm) Symbol

3x5.3 B55 6.3X5.3 F55 8X6.5 G68 10X10.0 H10

4x5.3 D55 6.3X5.7 F60 8X7.0 G72 10X13.0 H13

4x5.7 D60 6.3X6.0 F62 8X10.0 G10 12.5X13.5 K14

5x5.3 E55 6.3X7.0 F72 8X12.0 G12 12.5X16.0 K16

5x5.7 E60 6.3X7.7 F80 10X8.0 H82 16X16.0 L17

6. Package type: R Taping polarity symbol with reel package in 380 mm

M Taping polarity symbol with reel package in 450 mm

T Tray

SMD TYPECase Q’ ty / Reel Q’ ty / Box4 Ø 2,000 10,000

5 Ø 1,000 5,000

6.3 Ø 1,000 5,000

8 Ø x 6.5 ~ 7 L 1,000 5,000

8 Ø x 10 L 500 2,000

8 Ø x 11.8 L 400 2,000

10 Ø x 8 ~ 10 L 500 2,000

10 Ø x 12.7 L 400 2,000

12.5 Ø x 13.5 L 200 / 350* 800 / 1,400*

12.5 Ø x 16 L 150 / 300* 600 / 1,200*

16 Ø x 16.5 L 125 / 200* 500 / 800*

“ * “ Suitable for reel packing is 450 mm

PARTS NUMBER SYSTEM FOR THE SMD TYPE

E2 Series

E2

Series Name1

V

16V

16V

Rated Voltage2

10 μF

100

Capacitance3

4 Ø x 5.3L

D55

Symbol of Case Size

5

± 20%

M

CapacitanceTolerance

4

Carrier tape

R

Package type6

Unit: pcs

SMD ALUMINUM ELECTROLYTIC CAPACITORS 65

REFLOW CONDITION

Case size

Case code

Land sizeCase size Case

codeLand size

X Y W X Y W3x5.3 B55 1.6 2.2 0.8 8x6.5 G68 1.6 4.0 2.1

4x5.3 D55 1.6 2.6 1.0 8x7.0* G72 2.5 3.5 3.0

4x5.7 D60 1.6 2.6 1.0 8x10 G10 2.5 3.5 3.0

5x5.3 E55 1.6 3.0 1.4 8x12.0* G12 2.5 3.5 3.0

5x5.7 E60 1.6 3.0 1.4 10x8.0* H82 2.5 4.4 4.3

6.3x5.3 F55 1.6 3.5 1.9 10x10.0 H10 2.5 4.0 4.0

6.3x5.7 F60 1.6 3.5 1.9 10x13.0* H13 2.5 4.4 4.3

6.3x6.0* F62 1.6 3.5 2.1 12.5x13.5 K14 4.0 7.5 7.0

6.3x7.0* F72 1.6 3.5 2.1 12.5x16 K16 4.0 7.5 7.0

6.3x7.7 F80 1.6 3.5 1.9 16x16.5 L17 6.0 8.5 9.5

Case size in mark of “ * “ is for OC-CON capacitors application.

RECOMMENDED SOLDERING METHODS

Method Reflow soldering Soldering iron Flow soldering

Advisability

Recommended Recommended Not Recommended

LEAD-FREE TYPE

LEAD-FREE TYPE

Type Non-solid capacitor OC-CON

WV 4 ~50V 63V ~ 4V ~ - - -

Case size (Ø) 4 ~ 6.3 4 ~ 6.3 8 ~ 16 - - -

PreheatTemp.(T1 ~ T2, °C) 150 ~ 180

Time(t1)(Max, secs) 100 90

DurationTemp.(T3, °C) 217 230 217 217 200 217 230

Time(t2)(Max, secs) 90 60 60 40 60 50 40

PeakTemp.(T4, °C) 260 250 240 250 260

Time(t3, secs) 5 5 5 5 5

Reflow cycles 1 2 or less 2 1

Y Y

X

W

RECOMMENDED PAD PATTERN AND SIZE

(1) Method is as follow. Reflow soldering condition. The following temperature profile condition should be observed for soldering. (For high temperature, pleases contact us after measuring the capacitor’s product temperature profile at your side.) Product temperature will rise slower as the product size gets bigger. It is not necessary to adjust the reflow furnace temperature setting according to the product size, for example, Φ4 and Φ10 products can be mixed on one PCB forreflowing.

(2) Soldering precautions. 1. Elements related to the reflow soldering temperature * Product size: The temperature rises slower as the size gets bigger. * Product location: The center part of the PCB tends to have a lower temperature than the PCB edges. * Product size: The PCB temperature rises slower as the area and/or thickness of the PCB gets greater. 2. Repeated reflowing * Avoid reflowing twice if possible. * If repeated reflowing is unavoidable, contact us after measuring the first and second reflow profiles and reflow interval at your side. * Do not attempt to reflow three times. 3. Soldering with soldering iron Observe the follwing conditions. * The iron tip temperature: 350 ± 5°C * Soldering item: 3+1 / -0 seconds.

T1

Time

t1 t2

t3

T2

T3T4

Temperature (°C)

SMD ALUMINUM ELECTROLYTIC CAPACITORS

66

FEATURES . 3~10Ø, 85°C, 2,000 hours assured. . Chip type large capacitance capacitors. . Designed for surface mounting on high density PC board. . RoHS Compliance

SPECIFICATIONSItems Performance

Operating Temperature Range -40°C ~ +85°C

Capacitance Tolerance ±20°% (at 120Hz,20°C)

Leakage Current (at 20°C) I=0.01CV or 3(μA), whichever is greater (after 2 minutes) Where, C=rated capacitance in μF. V=rated DC working voltage in V.

Dissipation Factor (Tan δ at 120Hz, 20°C)

Rated Voltage 4 6.3 10 16 25 35 50 63 100

Tan δ(max) 0.42 0.28 0.24 0.20 0.14 0.12 0.10 0.10 0.10

Low Temperature Characteristics (ar 120Hz)

Impedance ratio shall not exceed the values given in the table below.

Rated Voltage 4 6.3 10 16 25 35 50 63 100

Impedance Ratio

Z(-25°C)Z(+20°C) 7 4 3 2 2 2 2 2 2

Z(-40°C)Z(+20°C) 15 8 5 4 3 3 3 3 3

Load Life Test

Test Time 2,000 Hrs

Capacitance Change Within ±20% of initial value (4WV; ±30%)

Dissipation Factor Less than 200% 0f specified value (4WV; ±300%)

Leakage Current Within specified value

*The above specifications shall be satisfied when the capacitors are restored to 20°C after the rated voltage applied for 2,000 hrs at 85°C.

Shelf Life Test Test time: 1,000 hrs; other items are the same as those for the load life test

Ripple Current &Frequency Multipliers

V.DC (V) Freg. (Hz) 50 120 1K 10K up

Under 16 0.8 1.0 1.15 1.25

25 ~ 35 0.8 1.0 1.25 1.40

50 ~ 63 0.8 1.0 1.35 1.50

100 0.7 1.0 1.35 1.50

Other Standards JIS C 5101-1,-18

LEAD SPACING AND DIAMETER Unit:mm

Ø D L A B C W P±0.2

3 5.3±0.2 3.3 3.3 1.5 0.45~0.75 0.8

4 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0

8 6.5±0.3 8.4 8.4 3.4 0.5 to 1.1 2.3

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7

VEVESeries

DIAGRAM OF DIMENSIONS

VE


DIMENSION & PERMISSIBLE RIPPLE CURRENT 4V(0G) 6.3V(0J) 10V(1A) 16V(1C) 25V(1E)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

4.7 47 4x5.3 19

10 100 4x5.3 23 4(3)x5.3 26(14) 5x5.3 32

22 220 3x5.3 14 4x5.3 23 5x5.3 394x5.3 30

6.3x5.3 555x5.3 44

33 330 4x5.3 31 4x5.3 314x5.3 33

6.3x5.3 635x5.3 54

5x5.3 48 6.3x5.3 67

47 470 4x5.3 344x5.3 37

6.3x5.3 675x5.3 52 6.3x5.3 75

5x5.3 50 6.3x5.3 75 * 8x6.5 155(98)

68 680 5x5.3 54 6.3x5.3 895x5.3 63

6.3x5.3 986.3x5.3 103

6.3x5.3 98 * 8x6.5 155(109)

100 101

5x5.3 58 5x5.3 63 5x5.3 65 6.3x5.3 110 6.3x7.7 124

6.3x5.3 89 6.3x5.3 986.3x5.3 110

* 8x6.5 155(108) * 8x6.5 155(124)* 8x6.5 155(108)

220 221 6.3x5.3 1106.3x5.3 110 6.3x7.7 124

* 8x10 252(124) 8x10 252* 8x6.5 155(123) * 8x6.5 155(130)

330 331 * 8x6.5 155(139) 8x10 252 8x10 252 10x10 458

470 471 8x10 252 10x10 458 10x10 458

1000 102 10x10 458 10x10 458

1500 152 10x10.3 458

35V(1V) 50V(1H) 63V(1J) 100V(1V)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

0.1 0R1 4x5.3 3

0.22 R22 4x5.3 5

0.33 R33 4x5.3 6

0.47 R47 4x5.3 7

1 010 4x5.3 10

2.2 2R2 4x5.3 15

3.3 3R3 3x5.3 8 4x5.3 19

4.7 4R7 4x5.3 204x5.3 20

5x5.3 26

10 1004x5.3 27 5x5.3 34

8x6.5 75 8x10 945x5.3 34 6.3x5.3 44

22 2205x5.3 47 6.3x5.3 59

8x10 139 10x10 1896.3x5.3 59 * 8x6.5 155(65)

33 3306.3x5.3 67 6.3x7.7 82

8x10 139 10x10 189* 8x6.5 155(85) * 8x6.5 155(82)

47 470 * 8x6.5 155(98)6.3x7.7 98

10x10 226* 8x10 252(98)

68 6806.3x7.7 109

8x10 252 10x10 226* 8x6.5 155(109)

100 101 * 8x10 2528x10 252

10x10 22610x10 458

220 221 10x10 458 10x10 458

* 6.3x7.7 is available and ( ) is its ripple current.

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 120 Hz,85°C

V.DC

Content

V.DC

Content

VE


68

FEATURES . 4~16Ø 85°C, 2,000 hours assured. . Designed for surface mounting on high density PC board. . RoHS Compliance




Leakage Current (at 20°C)6.3~100V

4~10Ø I=0.01CV or 3μA,whichever is greater,after 2 minutes at 20°C

12.5~16Ø I=0.03CV or 4μA,whichever is greater,after 2 minutes at 20°C

160~450V 12.5~16Ø I=0.04CV+100μA after 5 minutes at+20°C

Where I = leakage current C=rated capacitance in μF. V=rated DC working voltage in V.


Rated Voltage 6.3 10 16 25 35 50 63 100 160~250 400~450

4~10Ø 0.35 0.30 0.26 0.16 0.14 0.12 0.12 0.12 - -

12.5~16Ø 0.38 0.34 0.30 0.26 0.22 0.18 0.14 0.10 0.20 0.25

When the capacitance exceeds 1,000μF ,0.02 shall be added every 1,000μF increase.



Rated Voltage 6.3 10 16 25 35 50 63 100 160~250 400~450

Impedance Ratio

Z(-25°C)/Z(+20°C)

4~10Ø 4 4 3 2 2 2 2 3 - -

12.5~16Ø - 5 4 2 3 2 2 2 3 6

Z(-40°C)/Z(+20°C)

4~10Ø 17 10 8 4 3 3 3 4 - -

12.5~16Ø - 12 10 5 4 3 3 3 6 10

Load Life Test

Test Time 2,000 Hrs

Capacitance Change Within ±20% of initial value

Dissipation Factor Less than 200% 0f specified value






Ø D L A B C W P±0.2 Fig.No.

4 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.0 1

5 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5 1

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0 1

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0 1

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

8 10.3±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

10 10.3±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

12.5 13.5±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

12.5 16±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

16 16.5±0.5 16.3 16.3 5.8 1.1 to 1.4 6.0 2

EAEASeries


EA


DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H) 63V(1J)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

0.1 0R1 4x5.3 3 4x5.3 1.3

0.22 R22 4x5.3 5 4x5.3 3

0.33 R33 4x5.3 6 4x5.3 4

0.47 R47 4x5.3 7 4x5.3 5

1 010 4x5.3 10 4x5.3 8

2.2 2R2 4x5.3 15 4x5.3 12

3.3 3R3 4x5.3 15 5x5.3 17

4.7 4R7 4x5.3 19 4x5.3 18 4x5.3 18 5x5.3 20

10 100 4x5.3 26 4x5.3 26 4x5.3 24 4x5.3 24 5x5.3 30 6.3x.3 32

22 220 4x5.3 30 4x5.3 26 4x5.3 26 5x5.3 41 5x5.3 41 6.3x5.3 47 6.3x7.7 60

33 330 4x5.3 30 5x5.3 30 5x5.3 37 5x5.3 47 6.3x5.3 54 6.3x7.7 70 6.3x7.7 60

47 470 4x5.3 33 6.3x5.3 44 5x5.3 44 6.3x5.3 60 6.3x5.3 64 6.3x7.7 85 8x10 130

68 680 5x5.3 40 6.3x5.3 60 6.3x5.3 60 6.3x7.7 100 6.3x7.7 100 8x10 110 10x10 170

100 101 5x5.3 40 6.3x5.3 60 6.3x5.3 60 6.3x7.7 1006.3x7.7 120

8x10 130 12.5x13.5 3808x10 280

220 221 6.3x5.3 88 6.3x7.7 130 6.3x7.7 130 8x10 2608x10.3 280

10x10 170 12.5x13.5 58010x10 360

330 331 6.3x7.7 135 8x10 270 8x10 270 8x10.3 280 10x10.3 360 12.5x13.5 600 12.5x16 720

470 470 8x10 280 8x10 280 8x10 280 10x10 400 12.5x13.5 600 12.5x16 740 16x16.5 950

1000 102 8x10.3 430 10x10 430 12.5x13.5 710 12.5x13.5 820 16x16.5 1100

2200 222 12.5x13.5 890 12.5x13.5 960 16x16.5 1150 16x16.5 1450

1300 332 12.5x16 1000 16x16.5 1300 16x16.5 1150

4700 472 16x16.5 1400 16x16.5 1300

6800 682 16x16.5 1700

100V(2A) 160V(2C) 200V(2D) 250V(2E) 400V(2G) 450V(2W)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

4.7 4R7 12.5x13.5 120 12.5x13.5 120

10 100 8x10 90 12.5x13.5 150 12.5x13.5 120 12.5x16 130

22 220 8x10 90 12.5x13.5 240 12.5x13.5 150 16x16.5 140 16x16.5 140

33 330 10x10 120 12.5x13.5 240 12.5x16 310 12.5x16 240 16x16.5 140

47 470 10x10 120 12.5x16 370 16x16.5 340 16x16.5 340

68 680 12.5x13.5 380 16x16.5 500 16x16.5 340

100 101 12.5x13.5 380

220 221 16x16.5 500


V.DC

Content

V.DC

Content

EA


70

FEATURES . 4~6.3Ø 105°C, 1,000 hours assured. . Vertical chip type miniaturized forv 5.5mm high capacitor. . Designed for surface mounting on high density PC board. . RoHS Compliance






Rated Voltage 6.3 10 16 25 35 50Tan δ(max) 0.30 0.26 0.22 0.16 0.13 0.12


Impedance ratio shall not exceed the values given in the table below.Rated Voltage 6.3 10 16 25 35 50

Impedance RatioZ(-25°C)Z(+20°C) 4 3 2 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3 3

Load Life Test

Test Time 1,000 HrsCapacitance Change Within ±20% of initial value

Dissipation Factor Less than 200% 0f specified valueLeakage Current Within specified value




Freg. (Hz)V.DC (V) 50 120 1K 10K up

Under 16 0.8 1.0 1.15 1.25

25~35 0.8 1.0 1.25 1.40

50 0.8 1.0 1.35 1.50



Ø D L A B C W P±0.24 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.05 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0

DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H) µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

0.1 OR1 4x5.3 20.22 R22 4x5.3 30.33 R33 4x5.3 40.47 R47 4x5.3 5

1 010 4x5.3 72.2 2R2 4x5.3 103.3 3R3 4x5.3 124.7 4R7 4x5.3 12 4x5.3 14 5x5.3 1710 100 4x5.3 15 4x5.3 16 5x5.3 21 5x5.3 23 6.3x5.3 2622 220 4x5.3 21 5x5.3 25 5x5.3 28 6.3x5.3 36 6.3x5.3 50 6.3x5.3 5133 330 5x5.3 30 5x5.3 31 6.3x5.3 40 6.3x5.3 4447 470 5x5.3 36 6.3x5.3 43 6.3x5.3 47 6.3x5.3 60

100 101 6.3x5.3 61 6.3x5.3 65 6.3x5.3 70

ESESSeries

V.DCContent

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 120 Hz, 105°C


ES

71


FEATURES . 4~10Ø 105°C, 3,000 hours assured. . Long life assured. . Designed for surface mounting on high density PC board. . RoHS Compliance


Operating Temperature Range -40°C ~ +105°CCapacitance Tolerance ±20°% (at 120Hz,20°C)







Load Life Test







6.3 ~ 50 0.70 1.00 1.36 1.50



Ø D L A B C W P±0.24 5.7±0.3 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.7±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7


0.1 OR1 4x5.7 10.22 R22 4x5.7 2.60.33 R33 4x5.7 3.20.47 R47 4x5.7 5

1 010 4x5.7 82.2 2R2 4x5.7 123.3 3R3 4x5.7 174.7 4R7 4x5.7 16 5x5.7 2210 100 4x5.7 18 5x5.7 27 5x5.7 27 6.3x5.7 3222 220 4x5.7 22 4x5.7 30 5x5.7 30 6.3x5.7 44 6.3x5.7 44 6.3x7.7 5833 330 5x5.7 35 5x5.7 35 6.3x5.7 48 6.3x5.7 50 6.3x7.7 57 8x10 13047 470 5x5.7 38 6.3x5.7 50 6.3x5.7 50 6.3x7.7 63 8x10 141 8x10 141

100 101 6.3x5.7 69 6.3x7.7 81 6.3x7.7 81 8x10 141 10x10 290 10x10 310220 221 6.3x7.7 120 8x10 141 8x10 141 10x10 290 10x10 320330 331 8x10 290 10x10 290 10x10 290 10x10 320470 471 10x10 320 10x10 320 10x10 320

1000 102 10x10 410

EUEUSeries

V.DCContent



EU


72

FEATURES . 4~16Ø 105°C, 2,000 hours assured. . Designed for surface mounting on high density PC board. . RoHS Compliance




Leakage Current (at 20°C)6.3~100V

4~10Ø I=0.01CV or 3μA,whichever is greater,after 2 minutes at +20°C

12.5~16Ø I=0.03CV or 4μA,whichever is greater,after 2 minutes at +20°C

160~450V 12.5~16Ø I=0.04CV+100μA after 5 minutes at+20°C

Where I = leakage current C=rated capacitance in μF. V=rated DC working voltage in V.


Rated Voltage 6.3 10 16 25 35 50 63 100 160~250 400~450

4~10φ 0.45 0.35 0.28 0.18 0.16 0.14 0.12 0.12 - -

12.5~16φ 0.40 0.38 0.34 0.26 0.22 0.18 0.14 0.10 0.20 0.25

When the capacitance exceeds 1,000μF ,0.02 shall be added every 1,000μF increase.


Impedance ratio shall not exceed the values given in the table below.Rated Voltage 6.3 10 16 25 35 50 63 100 160~250 400~450

Impedance Ratio

Z(-25°C)/Z(+20°C)

4~10Ø 4 3 2 2 2 2 2 3 - -12.5~16Ø 5 4 3 2 2 2 2 2 3 6

Z(-40°C)/Z(+20°C)

4~10Ø 12 8 6 4 3 3 3 4 - -12.5~16Ø 10 8 6 4 3 3 3 3 6 10

Load Life Test

Test Time 2,000 Hrs

Capacitance Change4~6.3Ø : Within ±25% of initial value8~16Ø : Within ±20% of initial value







Ø D L A B C W P±0.2 Fig.No.

4 5.7±0.3 4.3 4.3 2.0 0.5 to 0.8 1.0 1

5 5.7±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5 1

6.3 5.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0 1

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0 1

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

8 10.3±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

10 10.3±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

12.5 13.5±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

12.5 16±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

16 16.5±0.5 16.3 16.3 5.8 1.1 to 1.4 6.0 2

GAGASeries


GA


DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H) 63V(1J)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

0.1 0R1 4x5.7 2

0.22 R22 4x5.7 3

0.33 R33 4x5.7 4

0.47 R47 4x5.7 5 4x5.7 5

1 010 4x5.7 10 4x5.7 8

2.2 2R2 4x5.7 16 4x5.7 12

3.3 3R3 4x5.7 18 5x5.7 17

4.7 4R7 4x5.7 13 4x5.7 16 5x5.7 20 6.3x5.7 22

10 100 4x5.7 17 5x5.7 23 5x5.7 27 6.3x5.7 32 6.3x5.7 32

22 220 5x5.7 30 6.3x5.7 38 6.3x5.7 44 6.3x5.7 47 6.3x7.7 58

33 330 5x5.7 30 6.3x5.7 45 6.3x5.7 50 6.3x5.7 54 6.3x7.7 65 8x10 140

47 470 5x5.7 30 6.3x5.7 48 6.3x5.7 48 6.35.7 60 6.3x7.7 80 6.3x7.7 808x10 170

10x10 310

100 101 6.3x5.7 69 6.3x5.7 69 6.3x5.7 69 6.3x7.7 100 8x10 3208x10 230

10x10.3 31010x10 375

220 221 6.3x7.7 120 6.3x7.7 120 6.3x7.7 120 8x10 320 10x10 375 10x10.3 375 12.5x13.5 470

330 331 8x10 290 8x10 290 8x10 290 10x10 375 10x10.3 410 12.5x13.5 500 16x16.5 700

470 471 8x10 3208x10 320

8x10 320 10x10 410 12.5x13.5 520 12.5x16 550 16x16.5 70010x10 410

1000 102 10x10 410 10x10.3 410 12.5x13.5 550 12.5x16 550 16x16.5 750

2200 222 12.5x13.5 680 12.5x16 750 16x16.5 950 16x16.5 820

3300 332 12.5x16 850 16x16.5 1000 16x16.5 950

4700 472 16x16.5 1,000 16x16.5 1000

6800 682 16x16.5 1,000

100V(2A) 160V(2C) 200V(2D) 250V(2E) 400V(2G) 450V(2W)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

3.3 3R3 12.5x13.5 65 12.5x13.5 40

4.7 4R7 12.5x13.5 68 12.5x13.5 50 12.5x13.5 50

10 100 12.5x13.5 80 12.5x13.5 72 12.5x13.5 65 12.5x16 55

22 220 8x10 100 12.5x13.5 90 12.5x13.5 90 16x16.5 85 16x16.5 85

33 330 10x10 150 12.5x13.5 95 12.5x16 110 16x16.5 180

47 470 12.5x13.5 250 12.5x16 110 16x16.5 220 16x16.5 180

100 101 12.5x13.5 380 16x16.5 190

220 221 16x16.5 450


V.DC

Content

V.DC

Content

GA


74

FEATURES . 4~10Ø,105°C, 2,000 hours assured. . Designed for surface mounting on high density PC board. . RoHS Compliance




Dissipation Factor (Tanδat 120Hz, 20°C)

Rated Voltage 6.3 10 16 25 35 50 63 1004 - 6.3Ø 0.32 0.28 0.24 0.18 0.15 0.14 - -8 - 10Ø 0.30 0.26 0.22 0.16 0.13 0.12 0.11 0.10


Impedance ratio shall not exceed the values given in the table below.Rated Voltage 6.3 10 16 25 35 50 63 100

Impedance Ratio

Z(-25°C)Z(+20°C) 4 3 2 2 2 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3 3 3 3

Load Life Test

Test Time 2,000 Hrs

Capacitance Change6.3V Within ±30% of initial value

10 ~ 16V Within ±25% of initial value25 ~100V Within ±20% of initial value

Dissipation Factor 6.3V ~16V Less than 300% 0f specified value25 ~ 100V Less than 200% 0f specified value

Leakage Current Within specified value *The above specifications shall be satisfied when the capacitors are restored to 20°C after the rated voltage applied for 2,000 hrs at 105°C.



V.DC (V) Freg. (Hz) 50, 60 120 1K 10K upUnder 16 0.8 1.0 1.15 1.2525 ~ 35 0.8 1.0 1.25 1.4050 ~ 63 0.8 1.0 1.35 1.50

100 0.7 1.0 1.35 1.50

Standards JIS C 5101-1,-18


Ø D L A B C W P±0.24 5.7±0.3 4.3 4.3 2.0 0.5 to 0.8 1.05 5.7±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.7±0.3 6.3 6.3 2.7 0.5 to 0.8 2.08 6.5±0.3 8.4 8.4 3.4 0.5 to 0.8 2.38 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.18 10.3±0.5 8.4 8.4 3.0 0.7 to 1.1 3.110 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.710 10.3±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7

DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H) 63V(1J) 100V(2A) µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

0.1 OR1 4x5.7 20.22 R22 4x5.7 30.33 R33 4x5.7 40.47 R47 4x5.7 5

1 010 4x5.7 102.2 2R2 4x5.7 163.3 3R3 4x5.7 184.7 4R7 4x5.7 13 4x5.7 13 4x5.7 13 5x5.7 2210 100 4x5.7 13 4x5.7 16 5x5.7 30 5x5.7 30 6.3x5.7 30 8x10 6722 220 4x5.7 13 5x5.7 27 5x5.7 30 6.3x5.7 38 6.3x5.7 50 8x6.5 65 8x10 99 10x1033 330 5x5.7 30 5x5.7 30 6.3x5.7 40 6.3x5.7 50 8x6.5 110 8x10 99 10x10 160 133

47 470 5x5.7 36 6.3x5.7 50 6.3x5.7 50 6.3x5.7 50 8x10 178 8x10 99 10x10 1608x10 178 8x6.5 110

100 101 6.3x5.7 61 6.3x5.7 61 8x10.3 178 8x10 178 10x10 324 10x10 160 10x10 1608x6.5 110

220 221 8x10 178 8x10 178 10x10 324 8x10 178 10x10 32410x10 324330 331 8x10 178 10x10 324 10x10 324 10x10.3 324470 471 10x10 324 10x10 324 10x10 324

EJEJSeries

V.DCContent



EJ


75EH

FEATURES . 4~10Ø, 105°C, 2,000 hours assured. . Vertical chip type miniaturized. . Low impedance capacitors. . Designed for surface mounting on high density PC board. . RoHS Compliance






Rated Voltage 6.3 10 16 25 35Tan δ(max) 0.30 0.26 0.22 0.16 0.13


Impedance ratio shall not exceed the values given in the table below.Rated Voltage 6.3 10 16 25 35

Impedance RatioZ(-25°C)Z(+20°C) 4 3 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3

Load Life Test

Test Time 2,000 HrsCapacitance Change Within ±20% of initial value (Ø ≤6.3: ±25%)





Freg. (Hz)V.DC (V) 50, 60 120 1K 10K up

6.3 ~ 35 0.64 0.8 0.93 1.0



Ø D L A B C W P±0.24 5.3±0.3 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.3±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.3 6.3 6.3 2.7 0.5 to 0.8 2.0

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7

10 10.3±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7

DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) µF Ø DxL lmp. mA Ø DxL lmp. mA Ø DxL lmp. mA Ø DxL lmp. mA Ø DxL lmp. mA4.7 4R7 4x5.7 3.2 65 4x5.7 3.2 6510 100 4x5.7 3.2 65 5x5.7 1.5 110 5x5.7 1.5 11022 220 5x5.7 1.5 110 6.3x5.7 0.85 170 6.3x5.7 0.85 17033 330 4x5.7 3.2 65 5x5.7 1.5 110 6.3x5.7 0.85 170 6.3x5.7 0.85 170 6.3x5.7 0.85 17047 470 5x5.7 1.5 110 6.3x5.7 0.85 170 6.3x5.7 0.85 170 6.3x5.7 0.85 170 8x10 0.45 450

100 101 6.3x5.7 0.85 170 6.3x5.7 0.85 170 8x10 0.45 450 8x10 0.45 450 8x10 0.45 450150 151 6.3x5.7 0.85 170 6.3x5.7 0.85 170 8x10 0.45 450 8x10 0.45 450 8x10 0.45 450

220 221 6.3x5.7 0.85 170 8x10 0.45 450 8x10 0.45 4508x10 0.45 450

10x10 0.25 67010X10 0.25 670

330 331 8x10 0.45 450 8x10 0.45 450 8x10 0.45 450 10x10.3 0.25 670470 471 8x10 .0.45 450 8x10 0.45 450 10x10 0.25 670820 821 10x10 0.25 670 10x10 0.25 670

1000 102 10x10 0.25 670

EHEHSeries

V.DC

Content

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 100k Hz, 105°CImpedance: Ω / at 100k Hz, 20°C



76

FEATURES . 4~6.3Ø, 105°C, 1,000 hours assured. . Low impedance capacitors. . Designed for surface mounting on high density PC board. . RoHS Compliance










Load Life Test






Freg. (Hz)V.DC (V) 50, 60 120 1K 10K up

6.3 ~ 50 0.64 0.8 0.93 1.0




4 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0

DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H)µF Ø DxL lmp. R.C. Ø DxL lmp. R.C. Ø DxL lmp. R.C. Ø DxL lmp. R.C. Ø DxL lmp. R.C. Ø DxL lmp. R.C.1.0 010 4x5.3 5.0 30

2.2 2R2 4x5.3 5.0 30

3.3 3R3 4x5.3 5.0 30

4.7 4R7 4x5.3 3.20 65 4x5.3 3.20 65 5x5.3 3.0 50

10 100 4x5.3 3.20 65 4x5.3 3.20 65 5x5.3 1.50 110 5x5.3 1.50 110 6.3x5.3 2.0 70

22 220 4x5.3 3.20 65 5x5.3 1.50 110 5x5.3 1.50 110 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x5.3 2.0 70

33 330 5x5.3 1.50 110 5x5.3 1.50 110 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x7.7 1.0 170

47 470 5x5.3 1.50 110 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x7.7 0.50 255

100 101 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x5.3 0.85 170 6.3x7.7 0.50 255

150 151 6.3x7.7 0.50 255 6.3x7.7 0.50 255 6.3x7.7 0.50 255220 221 6.3x7.7 0.50 255 6.3x7.7 0.50 255 6.3x7.7 0.50 255

EZEZ Series

V.DC

Content

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 100k Hz, 105°CImpedance: Ω at 100k Hz, 20°C


EZ

77


FEATURES . 4~ 16Ø, 105°C,2,000~5,000 hours assured .Large capacitance with ultra low impedance capacitors . Designed for surface mounting on high density PC board. . RoHS Compliance


Operating Temperature Range

6.3~63V 80~100V

-55°C ~ +105°C -40° ~ +105°C

Capacitance Tolerance ±20% (at 120Hz,20°C)

Leakage Current (at 20°C) I=0.01CV or 3μA, whichever is greater (after 2minutes)

Wher, C=rated capacitance in μF. V=rated DC working voltage in V.

Dissipation Factor (Tanδ at 120Hz, 20°C)

Rated Voltage 6.3 10 16 25 35 50 63 80 100

Tanδ (max) 0.30 0.26 0.22 0.16 0.13 0.10 0.08 0.08 0.07

When the capacitance exceeds1,000μF ,0.02shall be added every 1,000μF increase



Rated Voltage 6.3 10 16 25 35 50 63 80 100

Impedance Ratio

Z(-25°C)Z(+20°C) 4 3 2 2 2 2 2 2 2

Z(-40°C)Z(+20°C) 8 5 4 3 3 3 3 3 3

Load Life Test

Test Time 2,000 Hrs for 4 ~ 6.3Ø 5,000 Hrs for 8 ~ -16Ø

Capacitance Change Within ± 30% of initial value



* The above specifications shall be satisfied when the capacitors are restored to 20°C after the rated voltage applied for 2,000 ~ 5,000 hrs at 105°C.


Ripple Current & Frequency Multipliers

Freg. (Hz)V.dc (V) 50, 60 120 1K 10K up

6.3~100 0.64 0.8 0.93 1.0



Ø D L A B C W P±0.2 Fig. No.

4 5.7±0.3 4.3 4.3 2.0 0.5 to 0.8 1.0 1

5 5.7±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5 1

6.3 5.7±0.3 6.3 6.3 2.7 0.5 to 0.8 2.0 1

6.3 7.7±0.3 6.6 6.6 2.7 0.5 to 0.8 2.0 1

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

8 10.3±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

10 10.3±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

12.5 13.5±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

12.5 16±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

16 16.5±0.5 16.3 16.3 5.8 1.1 to 1.4 6.0 2

ZHZHSeries


ZH

78 SMD ALUMINUM ELECTROLYTIC CAPACITORSZH

DIMENSION & PERMISSIBLE RIPPLE CURRENT 6.3V(0J) 10V(1A) 16V(1C) 25V(1E) 35V(1V)

µF Ø DxL lmp mA Ø DxL lmp mA Ø DxL lmp mA Ø DxL lmp mA Ø DxL lmp mA

4.7 4R7 4x5.7 1.35 80

10 100 4x5.7 1.35 80 4x5.7 1.35 80 5x5.7 0.80 150

22 220 4x5.7 1.35 80 4x5.7 1.35 80 5x5.7 0.80 150 5x5.7 0.80 150 6.3x5.7 0.44 230

33 330 4x5.7 1.35 80 5x5.7 0.80 150 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x5.7 0.44 230

47 470 5x5.7 0.80 150 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x5.7 0.44 230

100 101 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x7.7 0.36 280 8x10 0.17 450

150 151 6.3x5.7 0.44 230 6.3x5.7 0.44 230 6.3x7.7 0.36 280 8x10 0.17 450 8x10 0.17 450

220 221 6.3x7.7 0.36 280 6.3x7.7 0.36 280 6.3x7.7 0.36 280 8x10 0.17 450 10x10 0.09 670

330 331 8x10 0.17 450 8x10 0.17 450 8x10 0.17 450 8x10.3 0.17 450 12.5x13.5 0.070 820

470 471 8x10 0.17 450 8x10 0.17 4508x10 0.17 450

10x10 0.09 670 12.5x16 0.060 95010x10 0.09 670

680 681 8x10.3 0.17 450 10x10 0.09 670 10x10.3 0.09 670 12.5x13.5 0.070 820 12.5x16 0.060 950

1000 102 8x10.3 0.17 450 10x10 0.09 670 12.5x13.5 0.070 820 12.5x16 0.060 950 16x16.5 0.054 1,260

1500 152 10x10.3 0.09 670 12.5x13.5 0.070 820 12.5x16 0.060 950 16x16.5 0.054 1,260

2200 222 12.5x13.5 0.070 820 12.5x16 0.060 950 16x16.5 0.054 1,260 16x16.5 0.054 1,260

3300 332 12.5x16 0.060 950 16x16.5 0.054 1,260 16x16.5 0.054 1,260

4700 472 16x16.5 0.054 1,260 16x16.5 0.054 1,260

6.3V(0J) 10V(1A) 16V(1C) 25V(1E)

µF Ø DxL lmp mA Ø DxL lmp mA Ø DxL lmp mA Ø DxL lmp mA

1 010 4x5.7 2.9 60

2.2 2R2 4x5.7 2.9 60

3.3 3R3 4x5.7 2.9 60

4.7 4R7 5x5.7 1.52 85 5x5.7 1.52 85

10 100 6.3x5.7 0.88 165 6.3x5.7 0.88 165

22 220 6.3x5.7 0.88 165 6.3x7.7 0.68 185

33 330 6.3x7.7 0.68 185 8x10 0.34 369

47 470 6.3x7.7 0.68 185 8x10 0.34 369 10x10 0.7 200 10x10 0.7 200

68 68 8x10 0.34 369 10x10 0.18 553 10x10.3 0.7 200 12.5x13.5 0.32 450

100 1018x10 0.34

369 10x10 0.18 553 12.5x13.5 0.32 450 12.5x16 0.26 55010x10 0.18

150 151 10x10.3 0.18 553 12.5x13.5 0.12 650 12.5x13.5 0.32 450 16x16.5 0.17 650

220 221 10x10.3 0.18 553 12.5x13.5 0.12 650 12.5x16 0.26 550

330 331 12.5x13.5 0.12 650 16x16.5 0.082 900 16x16.5 0.17 650

470 471 16x16.5 0.082 900 16x16.5 0.082 900

680 681 16x16.5 0.082 900

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 100 Hz,105°CImpedance: Ω / at 100k Hz, 20°C

V.DC

Content

V.DC

Content

79


FEATURES . 8~16Ø, 125°C, 1,000 hours assured. . Chip type high temperature range, for +125°C use. . For automobile modules and other high temperature applications. . RoHS Compliance


Operating Temperature Range10 ~ 50V

-40°C ~ +125°CCapacitance Tolerance ±20°% (at 120Hz,20°C)



Rated 10 16 25 35 50Tan δ(max) 0.32 0.24 0.21 0.18 0.18



Rated Voltage 10 16 25 35 50Impedance Ratio Z(-25°C)Z(+20°C) 5 4 3 3 3

Load Life Test







Ø D L A B C W P±0.2 Fig. No.

8 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 1

10 10±0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 1

12.5 13.5±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

12.5 16±0.5 12.8 12.8 4.9 1.1 to 1.4 4.2 2

16 16.5±0.5 16.3 16.3 5.8 1.1 to 1.4 6.0 2

DIMENSION & PERMISSIBLE RIPPLE CURRENT 10V(1A) 16V(1C) 25V(1E) 35V(1V) 50V(1H)

µF Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA Ø DxL mA

33 330 8x10 46

47 470 8x10 52 10x10 58

100 101 8x10 66 8x10 74 10x10 80 12.5x13.5 357

220 221 8x10 90 10x10 102 10x10 116 12.5x13.5 357 16x16.5 552

330 331 10x10 112 12.5x13.5 480 12.5x13.5 480 16x16.5 650 16x16.5 552

470 471 12.5x13.5 480 12.5x13.5 480 16x16.5 650 16x16.5 650

680 681 12.5x16 585 16.16.5 650

1000 102 12.5x16 585

UAUA Series

V.DC

Content

Dimension: Ø D x L(mm)Ripple Current: mA/rms at 100k Hz, 105°CImpedance: Ω at 100k Hz, 20°C


UA


80

FEATURES . 4~6.3Ø, 85°C, 2,000 hours assured. . Vertical chip type miniaturized . Non-polar capacitors for 5.5mm high capacitors . Designed for surface mounting on high density PC board. . RoHS Compliance






Rated Voltage 6.3 10 16 25 35 50

Tan δ(max) 4Ø 0.35 0.30 0.25 0.25 0.25 0.255~6.3Ø 0.30 0.25 0.20 0.15 0.15 0.15



Impedance Ratio

Z(-25°C)Z(+20°C) 3 3 2 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3 3

Load Life Test (with the polarity inverted

every 250 hours)

Test Time 2,000 HrsCapacitance Change Within±20% of initial value






Under 16 0.8 1.0 1.15 1.2525~35 0.8 1.0 1.25 1.40

50 0.8 1.0 1.35 1.50




4 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0


0.1 0R1 4x5.3 2.30.22 R22 4x5.3 3.30.33 R33 4x5.3 4.10.47 R47 4x5.3 4.9

1 010 4x5.3 7.22.2 2R2 4x5.3 10 5x5.3 143.3 3R3 4x5.3 13 5x5.3 17 5x5.3 174.7 4R7 4x5.3 14 5x5.3 20 5x5.3 21 6.3x5.3 2410 100 4x5.3 18 5x5.3 26 6.3x5.3 35 6.3x5.3 3522 220 5x5.3 27 6.3x5.3 40 6.3x5.3 4533 330 6.3x5.3 45 6.3x5.3 50 6.3x5.3 5547 470 6.3x5.3 54

EBEBSeries

V.DC

Content

Dimension: Ø D x L(mm), Ripple Current: mA/rms at 120 Hz,85°C


EB

81


FEATURES . 4~10Ø, 105°C, 2,000 hours assured. . Vertical chip type miniaturized . Low impedance capacitors . Designed for surface mounting on high density PC board. . RoHS Compliance





Rated Voltage 6.3 10 16 25 35 504~6.3Ø 0.32 0.28 0.24 0.18 0.15 0.148~10Ø 0.30 0.26 0.22 0.16 0.13 0.12



Impedance Ratio

Z(-25°C)Z(+20°C) 4 3 2 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3 3

Load Life Test

Test Time 2,000 Hrs (4~6.3Ø) 5,000 Hrs (8~10Ø)

Capacitance Change

6.3V Within ±30% of initial value Within ±30% of initial value 10 ~ 16V Within ±25% of initial value Within ±30% of initial value25 ~100V Within ±20% of initial value Within ±30% of initial value

Dissipation Factor

6.3V ~16V Less than 300% 0f specified value Less than 300% 0f specified value25 ~ 100V Less than 200% 0f specified value Less than 300% 0f specified value

Leakage Current Within specified value Within specified value *The above specifications shall be satisfied when the capacitors are restored to 20°C after the rated voltage applied for 2,000 hrs at 105°C.



Freg. (Hz)V.DC (V) 50, 60 120 1K 10K up

Under 16 0.8 1.0 1.15 1.2525~35 0.8 1.0 1.25 1.4050~63 0.8 1.0 1.35 1.50

100 0.7 1.0 1.35 1.50



Ø D L A B C W P±0.24 5.7±0.3 4.3 4.3 2.0 0.5 to 0.8 1.05 5.7±0.3 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.7±0.3 6.3 6.3 2.7 0.5 to 0.8 2.08 10±0.5 8.4 8.4 3.0 0.7 to 1.1 3.110 10±0.5 10.4 10.4 2.3 0.7 to 1.1 4.7


0.1 0R1 4x5.7 20.22 R22 4x5.7 30.33 R33 4x5.7 40.47 R47 4x5.7 5

1 010 4x5.7 102.2 2R2 4x5.7 163.3 3R3 4x5.7 184.7 4R7 4x5.7 13 4x5.7 13 4x5.7 13 5x5.7 2210 100 4x5.7 13 4x5.7 16 4x5.7 23 5x5.7 25 6.3x5.7 3022 220 4x5.7 13 5x5.7 30 5x5.7 30 6.3x5.7 38 6.3x5.7 50 8x10 17833 330 5x5.7 30 5x5.7 30 6.3x5.7 40 6.3x5.7 48 8x10 178 8x10 17847 470 5x5.7 36 6.3x5.7 43 6.3x5.7 50 8x10 178 8x10 178 8x10 178

100 101 6.3x5.7 61 8x10 178 8x10 178 8x10 178 10x10 324 10x10 160220 221 8x10 178 8x10 178 8x10 178 8x10 240 10x10 324330 331 8x10 178 10x10 324 10x10 324 10x10 324470 471 10x10 324 10x10 324 10x10 324

EKEKEKSeries

V.DCContent




82EC

FEATURES . 4~6.3Ø, 85°C, 2,000 hours assured. . Vertical chip type miniaturized for 5.5mm, high capacitors. . Low Leakage Current Lead free reflow soldering is available. . Designed for surface mounting on high density PC board. . RoHS Compliance




Leakage Current (at 20°C) I=0.002CV or 0.5(μA), whichever is greater (after 2 minutes) Where, C=rated capacitance in μF. V=rated DC working voltage in V.


Rated Voltage 6.3 10 16 25 35 50Tan δ(max) 0.28 .24 0.20 0.14 0.12 0.10



Impedance Ratio

Z(-25°C)Z(+20°C) 3 3 2 2 2 2Z(-40°C)Z(+20°C) 8 5 4 3 3 3

Load Life Test







Under 16 0.8 1.0 1.15 1.2525~35 0.8 1.0 1.25 1.40

50 0.8 1.0 1.35 1.50




4 5.3±0.2 4.3 4.3 2.0 0.5 to 0.8 1.0

5 5.3±0.2 5.3 5.3 2.3 0.5 to 0.8 1.5

6.3 5.3±0.2 6.6 6.6 2.7 0.5 to 0.8 2.0


0.1 OR1 4x5.3 30.22 R22 4x5.3 50.33 R33 4x5.3 60.47 R47 4x5.3 7

1 010 4x5.3 102.2 2R2 4x5.3 153.3 3R3 4x5.3 194.7 4R7 4x5.3 19 4x5.3 20 5x5.3 2610 100 4x5.3 23 4x5.3 26 5x5.3 32 5x5.3 34 6.3x5.3 4422 220 4x5.3 31 5x5.3 39 5x5.3 44 6.3x5.3 55 6.3x5.3 5933 330 5x5.3 44 5x5.3 48 6.3x5.3 63 6.3x5.3 6747 470 5x5.3 52 6.3x5.3 67 6.3x5.3 75

100 101 6.3x5.3 89 6.3x5.3 98

ECECSeries

V.DCContent

Dimension: Ø D x L(mm), Ripple Current: mA/rms at 120 Hz,85°C



memo


memo

Date post:	24-Jun-2020
Category:	Documents
Upload:	others
View:	3 times
Download:	1 times

ALUMINUM ELECTROLYTIC CAPACITORS INDEX 2008 Radial Leaded Full.… · RE Low ESR 105ºC 2000~3000...

Documents