Amano MJR8000 Series Manual (1)

8/22/2019 Amano MJR8000 Series Manual (1)

1/104

AMANO

MJR-8000 SeriesComputerized Time Recorder

Programming / User Guide


2/104

Amano Cincinnati Inc. reserves the right to make equipment changes and improvementsthat may not be reflected in this document. Portions of this document may have beenupdated to include the latest hardware or firmware version, if applicable.

We recommend that this document be read in its entirety before any attempt is made to

operate the equipment.

Proprietary Notice

This document contains proprietary information and such information may not bereproduced in whole or in part without written permission from:

Amano Cincinnati, Inc.140 Harrison AvenueRoseland, NJ, 07068

For more information about Amanos complete line of products, visit our web site at:

http://www.amano.com


3/104


4/104


5/104

General

[ 1 ]


6/104


7/104

General

[ 3 ]


8/104


9/104


10/104


11/104


12/104


13/104


14/104


15/104

INSTALLATION

** This page intentionally left blank **

[11]


16/104

INSTALLATION


[12]


17/104


18/104


19/104


20/104


21/104


22/104


23/104


24/104


25/104


26/104


27/104


28/104


29/104

PROGRAMMING GUIDE

*PROGRAMSETUP PROCEDURE

This part of the manual contains a chart to guide you through the

Program Setup Procedure.

For each step, refer to the page number for detailed instructions

on WHAT TO DO.

PROGRAM SETUP CHART

STEP WHAT TO DO USER ACCESS CODE PAGE

1 Initialize the ENTIRE clock 32 E 64 E P 4

2 Password Setup 11 E P 5, U

33

3 Raw Data Collection Programming 14 E P 6

4 Clock and Calendar Programming 10 E P 6

5 Time Card Number Assignment

Configuration Programming

13 E P 8

6 General Programming 20 E P 13

7 Signal Programming (OPTIONAL

Signal Kit must be installed to

send signal)

21 E P 15

8 Calculation Rules Programming 22 E P 18

9 Program Print-Out 23 E P 28

[P 3]


30/104


31/104

PROGRAMMING GUIDE

*PASSWORD SETUP

The MJR-8000 provides you with password protection for certain

Program and User Access Codes to offer you added security.

After the initialization procedure 32 E 64 E XXXX E the password

is automatically set to 0000. It is not required for you to changeyour password unless you require that extra security.

The areas that require a password are:

Initialization:

ALL memory (program and employee data) (32 E 64 E)

ALL employee data (30 E 88 E)

ALL program data (31E 99 E)

Time Card Number Assignment Programming Area (13 E)

Time Card Number Assignment (82 E and 83 E)

Lists with Pay Rates:

Employee Lists (64 E and 65 E)

Reports with Pay Rates or Dollar Amounts:

Individual Time Card Summary with Pay Rates (5 E and 6 E)

Accumulated Dollar$ Reports (44 E, 45 E, 46 E and 47 E)

Yesterdays Dollar$ Report (49 E)

Todays Dollar$ Report (51 E)

IF YOU WISH TO CHANGE THE EXISTING PASSWORD, REFER TO PAGE

[U 33] in the MJR-8000 Users Manual for detailed instructions.

[ P 5 ]


32/104


33/104

PROGRAMMING GUIDE


[P 7]


34/104


35/104


36/104


37/104


38/104


39/104


40/104


41/104


42/104


43/104


44/104


45/104


46/104


47/104


48/104


49/104


50/104


51/104


52/104


53/104


54/104


55/104


56/104


57/104


58/104


59/104


60/104


61/104


62/104


63/104


64/104


65/104


66/104


67/104


68/104


69/104


70/104


71/104


72/104


73/104


74/104


75/104


76/104


77/104


78/104


79/104


80/104


81/104


82/104


83/104


84/104


85/104


86/104


87/104


88/104


89/104


90/104


91/104


92/104


93/104


94/104


95/104


96/104


97/104


98/104


99/104


100/104


101/104


102/104


103/104


104/104

Date post:	08-Aug-2018
Category:	Documents
Upload:	mitchell-davis
View:	227 times
Download:	1 times

Amano MJR8000 Series Manual (1)

Documents