AMPL Libraries 3.2 RelNotes

Advant® OCSwith Master software

AMPL PC and DB Element Libraries

Version 3.2/0

Release Notes 3BDS011102D101

3BDS011102D101

3BS

E001264/ETemplate: 3BSE001286/E

Use of DANGER, WARNING, CAUTION, and NOTE

This publication includes, DANGER, WARNING, CAUTION, and NOTE information where appropriate to point out safety related or other important information.

DANGER Hazards which could result in severe personal injury or death

WARNING Hazards which could result in personal injury

CAUTION Hazards which could result in equipment or property damage

NOTE Alerts user to pertinent facts and conditions

Although DANGER and WARNING hazards are related to personal injury, and CAUTION hazards are associated with equipment or property damage, it should be understood that operation of damaged equipment could, under certain operational conditions, result in degraded process performance leading to personal injury or death. Therefore, comply fully with all DANGER, WARNING, and CAUTION notices.

TRADEMARKS

Adobe and Acrobat are trademarks of Adobe Systems Incorporated.

Advant, AdvaCommand, AdvaInform, and AdvaBuild are registered trademarks of ABB Asea Brown Boveri Ltd., Switzerland.

ABB Master is a registered trademark of ABB Asea Brown Boveri Ltd., Switzerland.

AdvaSoft, Advant Station, AdvaBuild On-line Builder, Advant Controller, and Advant Fieldbus are trademarks of ABB Asea Brown Boveri Ltd., Switzerland.

IBM and all IBM-products mentioned in this publication are registered trademarks of International Business Machines Corp.

Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation.

NOTICE

The information in this document is subject to change without notice and should not be construed as a commitment by ABB Automation Products GmbH. ABB Automation Products GmbH assumes no responsibility for any errors that may appear in this document.

In no event shall ABB Automation Products GmbH be liable for direct, indirect, special, incidental or consequential damages of any nature or kind arising from the use of this document, nor shall ABB Automation Products GmbH be liable for incidental or consequential damages arising from use of any software or hardware described in this document.

This document and parts thereof must not be reproduced or copied without ABB Automation Products GmbH’s written permission, and the contents thereof must not be imparted to a third party nor be used for any unauthorized purpose.

The software described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license.

Copyright © ABB Automation Products GmbH 2003.

AMPL PC and DB Element Libraries Release NotesTable of Contents

3BDS011102D101 3

TABLE OF CONTENTS

Chapter 1 - Introduction1.1 Executive Summary................................................................................................. 1-1

1.2 How to Use This Document..................................................................................... 1-1

1.3 Version Designation................................................................................................. 1-1

1.4 Revision Record....................................................................................................... 1-2

1.5 Compatibility ........................................................................................................... 1-3

1.6 Restrictions .............................................................................................................. 1-3

1.7 Related Documentation............................................................................................ 1-3

Chapter 2 - Functionality2.1 New Functions ......................................................................................................... 2-1

2.1.1 Overview................................................................................................. 2-1

2.1.2 Support of AC 160 2.2............................................................................ 2-1

2.2 Discontinued and Replaced Functions and Units .................................................... 2-3

2.3 Fixed Problems ........................................................................................................ 2-3

2.3.1 Incomplete message ’Duplicate Option’.................................................. 2-3

2.4 Known Problems and Work Arounds ...................................................................... 2-3

2.4.1 Check of Available Disk Space .............................................................. 2-3

2.5 Recommendations.................................................................................................... 2-4

Chapter 3 - Installation3.1 Installation ............................................................................................................... 3-1

3.1.1 Installation Procedure ............................................................................. 3-1

3.1.2 Custom Installation ................................................................................. 3-9

3.1.3 Installation on a Server ......................................................................... 3-13

3.2 Prerequisites........................................................................................................... 3-14

3.2.1 Hardware Requirements ....................................................................... 3-14

3.2.2 Software Requirements......................................................................... 3-14

3.3 Overview of Third Party Products ......................................................................... 3-15

3.4 Overview of Installation Order and Deinstallation Order ..................................... 3-15

3.5 Un-install ............................................................................................................... 3-15

3.6 Upgrading .............................................................................................................. 3-15

3.7 Backup and Restore ............................................................................................... 3-16

Chapter 4 - Miscellaneous4.1 System Specification................................................................................................ 4-1

AMPL PC and DB Element Libraries Release NotesSection 1.1Executive Summary

Chapter 1 Introduction

1.1 Executive SummaryThese Release Notes contains information about AMPL PC and DB Element Libraries version 3.2/0 which belongs to basic unit Control Builder A 1.2.

AMPL PC and DB Element Libraries consist of

• AC 450 AMPL Libraries (including on-line reference manuals)






• MP200/1 AMPL Libraries

• AdvaSoft AMPL Libraries, AdvaSoft 1.x only.

All products are running on Windows NT and Windows 2000.

NOTE

AMPL PC and DB Element Libraries do not require any license.

1.2 How to Use This DocumentIt is recommended that you first read through this document before installing AMPL PC and DB Element Libraries, because the requirements and prerequisites to install and use it are described here. The installation is described in Chapter 3, Installation.

You will find this document on the CD-ROM labelled Advant Engineering Software CD4, in the root directory. The Release Notes will also be copied during installation to the Local Configuration directory (ADVABLDENV). You have access to them by Start > Programs > ABB Industrial IT > Product Suite > Engineer IT > Control Builder A > Documentation > AMPL PC and DB Libraries 3.2-0 Release Notes.

1.3 Version DesignationAMPL PC and DB Element Libraries 3.2/0 comes along with the following AMPL libraries:

• AC 450 AMPL Libraries 3.2/0




3BDS011102D101 1-1

AMPL PC and DB Element Libraries Release NotesSection 1.4Revision Record



• MP 200/1 AMPL Libraries 3.2/0

• AdvaSoft AMPL Libraries 3.2/0, AdvaSoft 1.x only.

NOTE

The version identification of each AMPL library is not the version of a target type.

1.4 Revision RecordThe following versions and revisions have been produced:

Table 1-1. Current Revision

Version Release Date Remarks

AMPL PC and DB Element Libraries 3.2/0

15-May-2003 for Control Builder A 1.2/0

Table 1-2. Earlier Versions

Version Release Date Remarks


12-Dec-1997 First version for Windows NT,for AMPL Control Configuration 1.4/0


03-Apr-1998 for AMPL Control Configuration 1.5/0




15-May-1998 for AMPL Control Configuration 1.5/2


05-Feb-1999 for AMPL Control Configuration 1.6/0




14-JAN-2000 for AMPL Control Configuration 1.7/0


11-Aug-2000 for AMPL Control Configuration 2.0/0

3BDS011102D101 1-2

AMPL PC and DB Element Libraries Release NotesSection 1.5Compatibility

1.5 CompatibilityAMPL PC and DB Element Libraries 3.2/0 include the libraries valid for Function Chart Builder 6.2/0 and also AMPL PC and DB Element Libraries valid for Function Chart Builder 6.1/0. AMPL PC and DB Libraries 3.2/0 can also be installed for revisions of Function Chart Builder 6.2/0. The included AMPL PC and DB Libraries for Function Chart Builder 6.1/0 can be installed for all revisions of Function Chart Builder 6.1.

See also Control Builder A Release Notes.

1.6 RestrictionsAMPL PC and DB Element Libraries do not contain any Library for Function Chart Builder <= 6.0.

1.7 Related DocumentationThe reference manuals listed in Table 1-3 are related to AMPL PC and DB Element Libraries.

The recent editions are highlighted.


09-Apr-2001 for Control Builder A 1.0/0


08-Mar-2002 for Control Builder A 1.1/0

Table 1-2. Earlier Versions

3BDS011102D101 1-3

AMPL PC and DB Element Libraries Release NotesSection 1.7Related Documentation

Table 1-3. AMPL PC and DB ELement Library Manuals

Document Title Controller Version / Software Version Year Ident No.

Data Base Elements Advant Controller 400 Series Reference Manual

AC 450*1.0 and 1.1 AC 450 with SW QC02-BAS21*7.0


AC 450*1.2 AC 450 with SW QC02-BAS21*8.0




AC 450* 2.0 AC 450 with SW QC07-BAS41*1.0






1995

1996

1997

1997

1998

1999

199920002001

3BSE002422R0001RevA

3BSE002422R0001RevB

3BSE002422R0101RevA

3BSE014819R0001

3BSE014819R0101

3BSE014819R201

3BSE014819R3013BSE014819R4013BSE014819R401 Rev.A

3BDS011102D101 1-4


PC Elements Advant Controller 400 Series Reference Manual













1995

1996

1997

1997

1998

1999

2001

3BSE002418R0001

3BSE002418R0101

3BSE002418R0201

3BSE002418R0301

3BSE002418R0401

3BSE002418R501

3BSE002418R601

3BSE002418R601 Rev.A


AC 110 2.0AC 110 2.1AC 110 2.2AC 110 2.3

19961997199819991999200020012002

3BSE000505R0101RevA3BSE000505R0201RevA3BSE000505R03013BSE000505R4013BSE000505R5013BDS100594R1013BDS100594R2013BDS100594R301


AC 110 2.0AC 110 2.1 and 2.2AC 110 2.3

199519971999

3BSE000504R0101RevA3BSE000504R02013BSE000504R301



3BDS011102D101 1-5


The manuals related to Control Builder A are listed in the following manual:


AC 160 1.0AC 160 1.2AC 160 2.0

AC 160 2.1

AC 160 2.2

199919992000200120022003

GKWF310366R00013BDS005556R13BDS005556R1013BDS005556R2013BDS005556R3013BDS005556R4013BDS005556R501


AC 160 1.0AC 160 1.2AC 160 2.0AC 160 2.1AC 160 2.2

1999199920012003

GKWF310365R00013BDS005557R13BDS005557R1013BDS005557R2013BDS005557R301

Data Base Elements Advant Controller 70 Reference Manual

AC 70 1.0AC 70 1.1AC 70 1.2

199619971999199920002002

3BSE009456R00013BSE009456R0101RevA3BSE009456R2013BSE009456R3013BDS100593R1013BDS100593R101RevA

PC Elements Advant Controller 70 Reference Manual

AC 70 1.0AC 70 1.1 and 1.2

199619971999

3BSE009177R00013BSE009177R01013BSE009177R201

Data Base Elements Advant Controller 55 Reference Manual

AC 55 1.0AC 55 1.1

19961997

3BSE006525R0001RevA3BSE006525R0101

PC Elements Advant Controller 55 Reference Manual

AC 55 1.0AC 55 1.1

19951997

3BSE006526R00013BSE006526R0101

MasterPiece 200/1Data Base Elements

MP 200/1*4.0, 3.0, 2.1, 2.0 1992 7650 063-212

MasterPiece 200/1 PC Elements MP 200/1*3.0, 2.1, 2.0MP 200/1*4.0

19901992

7650 063-209/17650 063-211

Table 1-4. Control Builder A Manuals

Document Ordering No.

Control Builder A Installation Guide 3BDS011136R101



3BDS011102D101 1-6

AMPL PC and DB Element Libraries Release NotesSection 2.1New Functions

Chapter 2 Functionality

2.1 New Functions

2.1.1 OverviewAMPL PC and DB Element Libraries 3.2/0 belong to Control Builder A 1.2/0. They include AMPL library sets for all the target types listed below as well as on-line reference manuals in electronic format if applicable. Each set of libraries will update Function Chart Builder 6.2/0 in order to support a certain target type including all versions being released. In addition libraries for Function Chart Builder 6.1 can be updated.

Without installing AMPL PC and DB Element Libraries, Function Chart Builder 6.2/0 cannot be used for these targets.

With regard to Function Chart Builder 6.1 no new target types are supported.

• AC 450 AMPL Libraries 3.2/0 support

– Advant Controller 450 with SW QC02-BAS21*7.0, 8.0 and 9.0.

– Advant Controller 450 with SW QC07-BAS41*1.0, 2.0, 3.0 and 4.0.

• AC 410 AMPL Libraries 3.2/0 support Advant Controller 410 with SW QC01-BAS11*7.0, 8.0, 9.0, 10.0, 11.0 and 11.0/1.

• AC 110 AMPL Libraries 3.2/0 support Advant Controller 110*2.0, 2.1, 2.2 and 2.3.

• AC 160 AMPL Libraries 3.2/0 support Advant Controller 160*1.0, 1.1, 1.2, 2.0, 2.1 and 2.2.

• AC 70 AMPL Libraries 3.2/0 support Advant Controller 70*1.0, 1.1 and 1.2.

• AC 55 AMPL Libraries 3.2/0 support Advant Controller 55*1.0 and 1.1.

• MP 200/1 AMPL Libraries 3.2/0 support MasterPiece 200/1*2.0, 2.1, 3.0 and 4.0.

• AdvaSoft AMPL Libraries 3.2/0 support AdvaSoft*1.0, 1.1, 1.2 and 1.3.

NOTE

The previous version of Function Chart Builder 6.1 can also be updated. This has to be selected during setup.

2.1.2 Support of AC 160 2.2The Function Chart Builder 6.2/0 supports AMPL PC and DB Element Libraries for Advant Controller * 2.2 .

The new /changed functions of AC 160 2.2 in comparison with AC 160 2.1 are:

– Support of Terminal BIOB_SPD for DB Elements PM*

3BDS011102D101 2-1

AMPL PC and DB Element Libraries Release NotesSection 2.1.2Support of AC 160 2.2

– New Option “OPT 8: Warm Start 2.2”.

– Support of Terminal SINGLE for DB Elements PM*

– Increase number of DB Elements MDAT

– DP640 Safety Relevant Parameters

– Support of DI830

– Support Master Fieldbus Coupler CI671 in AC 160

– Support of Terminal AST_OFFS for DB Element PM665

– Support of Terminals TIM_SYNC for DB Element CI810

– Support new Terminals for SYSL PC Element

– Support PC Element SYSLCON

– Support Terminal FORCESWO for the DB Elements CI630/CI631

– Support Terminal PRIMARY for the DB Elements CI630/CI631

– Support Terminal BL_CSWO for the DB Elements CI630/CI631

– Support Terminal BL_INIT for the DB Elements CI630/CI631

– Support Intrinsic Safety modules AI890, AI895, AO890, AO895, DI890, DO890

For detailed information about new and changed PC and DB Elements see PC and DB element reference manuals.

3BDS011102D101 2-2

AMPL PC and DB Element Libraries Release NotesSection 2.2Discontinued and Replaced Functions and Units

2.2 Discontinued and Replaced Functions and UnitsThe following functions are discontinued since the AMPL Library version 3.1/0:

none

2.3 Fixed ProblemsThe following problems have been fixed since the AMPL Library version 3.1/0:

2.3.1 Incomplete message ’Duplicate Option’The utility program Setup Add-Ons version can be used to add user defined libraries for use in Function Chart Builder. This utility program delivers an incomplete message in case of duplicate option names. The following message appears:

"Duplicate option ’optionname’ in .

This message is incomplete. The name of the duplicate option is missing.

The TED file name where the duplicate option is included has been appended.

This has been corrected.

2.4 Known Problems and Work AroundsThe following problem is known for AMPL Library version 3.2/0:

2.4.1 Check of Available Disk SpaceThe check for available disk spaces is done for all selected library options after Select Library Options dialog see Figure 3-2.

This is wrong in case the libraries shall be installed on a server without manuals.

In case there is not enough disk space on the drive of AEP_BUILDERS the following message appears see Figure 2-1. It is not possible to proceed the installation in this case.

Workaround:

• Change system variable AEP_BUILDERS to the drive of server installation or

Figure 2-1. Warning Disk Space

3BDS011102D101 2-3

AMPL PC and DB Element Libraries Release NotesSection 2.5Recommendations

• Unselect library options one library option after the other

2.5 RecommendationsThere are no special recommendations concerning usage of AMPL PC and DB Element Libraries.

3BDS011102D101 2-4

AMPL PC and DB Element Libraries Release NotesSection 3.1Installation

Chapter 3 Installation

3.1 InstallationThe pictures for detailed installation are an example for the generation workflow. The included versions of product and components are not necessarily related to Function Chart Builder 6.2.

3.1.1 Installation ProcedureIt is recommended that you first read through this chapter before you start the installation.

To install AMPL PC and DB Element Libraries, perform the following steps:

1. Make sure that Control Builder A including Function Chart Builder 6.2 (or 6.1) is installed.

2. Start SETUP.EXE on the root directory of CD-ROM Advant Engineering Software CD4. After a short initialization procedure the Welcome dialog is displayed:

Click Next.

Figure 3-1. Welcome Dialog

3BDS011102D101 3-1

AMPL PC and DB Element Libraries Release NotesSection 3.1.1Installation Procedure

3. The installation program opens the Select Library Options dialog.

Check the library options you want to install.Uncheck the library options you do not want to install.

NOTES

The version number 3.2/0 is the version identification of the AMPL library, not the version of a target type. Each AMPL library includes support for all available versions released for a target type.

If Control Builder A Select Product is used, the library options AC 410, AC 450, and MP200/1 are not available.

Click Next.

Figure 3-2. Select Library Options Dialog

3BDS011102D101 3-2


4. The installation program opens the Setup Type dialog.

Select one of the setup types:

a. Server: Install the libraries for a server/network installation of Function Chart Builder. This kind of installation is described in detail in Chapter 3.1.3, Installation on a Server.

b. Local: Install the libraries for a local installation of Function Chart Builder. The libraries will be installed on your local PC.

Choose Next.

Figure 3-3. Setup Type Dialog

3BDS011102D101 3-3


5. The installation program opens the Choose Default Setup Type dialog.

If you wish to install all library options with the same setup type (Typical, Compact, or Custom), you can make this selection here. Otherwise leave the No default setting and you will be asked to choose a setup type for each library option selected in Step 3 above.

Select one of the types:

a. Typical: Install libraries and on-line reference manuals for Function Chart Builder 6.2. The easy setup type, no further questions will be asked.

b. Compact: Install the libraries for Function Chart Builder 6.2, but no on-line reference manuals. No further questions will be asked.

c. Custom: Select each setting individually, i.e. select Function Chart Builder version(s) to install libraries for, and setup the destination path for on-line manuals. See Section 3.1.2, Custom Installation for details.

d. No default: You will select the setup type individually for each library option selected in Step 3 above.

Click Next.

Figure 3-4. Choose Default Setup Type Dialog

3BDS011102D101 3-4


6. In case of “Typical” or “Compact” library installation, the installation program shows the Start Copying Files Dialog. It summarizes the current settings

If the current settings are ok, click Next.

NOTE

The Manuals Folder can only be changed in Custom Setup see Chapter 3.1.2, Custom Installation.

Now the individual setup of each library option that has been selected is started automatically without further questions. Go on with Step 9.

Figure 3-5. Start Copying Files Dialog

3BDS011102D101 3-5


7. In case of “No Default” library installation, the installation program shows the Setup Type Dialog for each selected library option:

Select one of the types:

a. Typical: Install libraries and on-line reference manuals for Function Chart Builder 6.2.

b. Compact: Install the libraries for Function Chart Builder 6.2, but no on-line reference manuals.

c. Custom: Select each setting individually, i.e., select Function Chart Builder version(s) to install libraries for, and setup the destination path for on-line manuals. See Section 3.1.2, Custom Installation for details.

Click Next.

Figure 3-6. Setup Type Dialog

3BDS011102D101 3-6


8. The installation program summarizes the settings for the actual library option in the Start Copying Files dialog.

If the current settings are ok, click Next.

NOTE

The Manuals Folder can only be changed in Custom Setup see Chapter 3.1.2, Custom Installation. The default manuals folder is ’MAN\12r0’. The version of the manuals folder don’t change for different AMPL Library versions. Already existing manuals on this location are updated by the installation.

9. This step is the start of the installation sequence repeated for each selected library option.

The installation of the first—or next—selected library option starts. If the library option is already installed on your system, the following warning messages are displayed:

Figure 3-7. Start Copying Files Dialog

3BDS011102D101 3-7


It is strongly recommended that you first uninstall the old library option.

After copying library and manual files, the following message box appears to indicate that the library files are being updated for a specific Function Chart Builder version. This may take a while depending on the amount and size of files:

If there are more library options to be installed, the installation program goes back to

• Step 9 in case of “Typical”, “Compact”, or “Custom” installation.

• Step 7 in case of “No Default” installation.

Figure 3-8. Warning Message ’Already Installed’

Figure 3-9. Warning Message ‘Override’

Figure 3-10. Message ‘Updating Library Files’

3BDS011102D101 3-8

AMPL PC and DB Element Libraries Release NotesSection 3.1.2Custom Installation

10. At the end, the installation program shows the Setup Complete dialog.

Click Finish.

3.1.2 Custom InstallationCustom installation steps are executed in the following ways:

• Before Step 9 if you select Custom in Step 5 above.

• Before Step 8 if you select No Default in Step 5 and Custom in Step 7 above.

The Custom Setup is needed

• If more than one Function Chart Builder version is installed and the libraries should be updated.

• To define the location of the manuals.

Figure 3-11. Setup Complete Dialog

3BDS011102D101 3-9


1. The installation program shows the Select Components dialog:

Check the components you want to install.

Uncheck the components you do not want to install.

Click the Change... button to check library sub-components:

Figure 3-12. Select Components Dialog

3BDS011102D101 3-10


Check the sub-components you want to install and click Continue.

NOTES

AMPL PC and DB Libraries Setup 3.2/0 can install libraries for Function Chart Builder 6.2 and Function Chart Builder 6.1. It is also possible to install libraries to future Function Chart Builder releases.

By default only the Function Chart Builder version is checked the installation program is related to. For Libraries Version 3.2/0 this is Function Chart Builder 6.2/0.

• If you uncheck Libraries for Function Chart Builder 6.2 and check them again, all installed versions of Function Chart Builder 6.2 are selected.

• If you check Libraries for Function Chart Builder 6.1, all installed versions of Function Chart Builder 6.1 are selected.

Click Next.

Figure 3-13. Select Sub-components Dialog

3BDS011102D101 3-11


2. In case that the Manuals component is checked, the installation program shows the Choose Destination Location dialog:

Select the path for the on-line reference manuals.

NOTE

The specified location of manuals is used for all further installations. The location is used during the installation of PC and DB element libraries to update links to on-line manuals.The default manuals folder is ’MAN\12r0’. The version of the manuals folder don’t change for different AMPL Library versions. Already existing manuals on this location are updated by the installation.

Choose Next.

Figure 3-14. Choose Destination Dialog

3BDS011102D101 3-12

AMPL PC and DB Element Libraries Release NotesSection 3.1.3Installation on a Server

3. The installation program summarizes the settings in the Start Copying Files dialog:

NOTE

If several Function Chart Builder versions and revisions are installed and selected in Step 1, the installation program shows them in the Start Copying Files dialog.

If the current settings are ok, choose Next.

3.1.3 Installation on a ServerPrerequisites:

The Function Chart Builder has to be installed as server (network) installation, see Function Chart Builder server setup as part of Control Builder A server setup in Control Builder A Release Notes.

Figure 3-15. Start Copying Files

3BDS011102D101 3-13

AMPL PC and DB Element Libraries Release NotesSection 3.2Prerequisites

Choose the destination location. Choose the same folder that was chosen for Function Chart Builder server installation.

Choose Next.

The installation program continues the steps described in Chapter 3.1.1, Installation Procedure Step 5 to Step 10.

After the library server setup perform the client setup from the Function Chart Builder as part of Control Builder A client setup on every client PC see Control Builder A Release Notes. See also Chapter 3.4, Overview of Installation Order and Deinstallation Order

3.2 Prerequisites

3.2.1 Hardware RequirementsSee Control Builder A Release Notes.

3.2.2 Software RequirementsControl Builder A with Function Chart Builder 6.2 or Function Chart Builder 6.1 must be installed. Other requirements are listed in the Control Builder A Release Notes.

Figure 3-16. Choose Destination Location Dialog for Server Installation

3BDS011102D101 3-14

AMPL PC and DB Element Libraries Release NotesSection 3.3Overview of Third Party Products

3.3 Overview of Third Party ProductsAcrobat Reader 4.0 is provided on the CD-ROM labelled AdvaBuild Engineering Software CD1 for reading release notes and on-line manuals.

3.4 Overview of Installation Order and Deinstallation Order• Local Installation

– Install Control Builder A with Function Chart Builder 6.2 or Function Chart Builder 6.1 as local installation.

– Install AMPL PC and DB Libraries as local installation.

– Deinstallation of AMPL PC and DB Libraries should be performed before deinstallation of Function Chart Builder see Control Builder A Release Notes.

• Server Installation

– Install Control Builder A with Function Chart Builder 6.2 or Function Chart Builder 6.1 as server installation.

– Install AMPL PC and DB Libraries as server installation.

– Perform Function Chart Builder setup as part of Control Builder A client setup on each client see Control Builder A Release Notes. With this step all libraries installed on server are also available on the client PCs.

– Deinstallation of AMPL PC and DB Libraries is not possible from a client PC.

– Deinstallation of Function Chart Builder on the client is provided via the Add/Remove Programs icon in the Control Panel see Control Builder A Release Notes.

– Deinstallation of Function Chart Builder on the server is provided via the Add/Remove Programs icon in the Control Panel see Control Builder A Release Notes.

3.5 Un-installUn-install is provided via the Add/Remove Programs icon in the Control Panel.

To uninstall AMPL Libraries, select the Add/Remove Programs icon, select the AMPL Libraries version you want to uninstall, e.g., AC 110 AMPL Libraries 3.1/0 and click Change/Remove to uninstall it.

To uninstall Function Chart Builder, select the Install/Uninstall tab, select the Function Chart Builder version you want to uninstall, e.g., Function Chart Builder 6.1/0 and click Change/Remove to uninstall it.

3.6 UpgradingNot applicable.

3BDS011102D101 3-15

AMPL PC and DB Element Libraries Release NotesSection 3.7Backup and Restore

3.7 Backup and RestoreNot applicable.

3BDS011102D101 3-16

AMPL PC and DB Element Libraries Release NotesSection 4.1System Specification

3BDS011102D101 4-1

Chapter 4 Miscellaneous

4.1 System SpecificationAll recommendations, prerequisites, and system setting for using AMPL PC and DB Element Libraries are described in the Control Builder A Installation Guide.

Date post:	21-Oct-2015
Category:	Documents
Upload:	enricscribd
View:	185 times
Download:	9 times

AMPL Libraries 3.2 RelNotes

Documents