Home >Documents >Anisotropic Aquifers

Anisotropic Aquifers

Date post:24-Feb-2016
Category:
View:40 times
Download:0 times
Share this document with a friend
Description:
Anisotropic Aquifers. Tripp Winters . Horizontal Plane Anisotropy. Anisotropy is a common feature in water laid sedimentary deposits (fluvial, clastic lake, deltaic and glacial outwash). Water lain deposits may exhibit anisotropy on the horizontal plain (X,Y if looking down from above) - PowerPoint PPT Presentation
Transcript:

Anisotropic Aquifers

Anisotropic AquifersTripp Winters Anisotropy is a common feature in water laid sedimentary deposits (fluvial, clastic lake, deltaic and glacial outwash). Water lain deposits may exhibit anisotropy on the horizontal plain (X,Y if looking down from above)Hydraulic conductivity in the direction of flow tends to be greater than that perpendicular to flow, which causes lines of equal drawdown to form ellipses rather than circles.

Horizontal Plane Anisotropy

Water laid sedimentary deposits are often stratified (have layers of alternating stratum, therefore alternating Ks)Any layer with a low K will retard vertical flow, but horizontal flow can occur easily through any layer with relatively high K. When Kh (parallel to the layer) is larger than Kv (perpendicular to layer), the aquifer is said to be Vertically anisotropic.

Vertical Plane Anisotropy

When an aquifer exhibits both vertical and horizontal anisotropy, it has 3-D anisotropy

The principal axes are:Kz: the vertical directionKparallel: The direction parallel to stream flowKperpendicular: The direction perpendicular to stream flow

3-D Anistropy

The assumptions listed at the beginning of Chapter 3, with the exception of the third assumption, which is replaced by:The aquifer is homogeneous, anisotropic on the horizontal plane, and of uniform thickness over the area influenced by the pumping test.

Some conditions are added:The flow to the well is in unsteady state;If the principal directions of anisotropy are known, drawdown data from two piezometers on different rays from the pumped well will be sufficient. If the principal directions of anisotropy are not known, drawdown data must be available from at least three rays of piezometers.

Hantush Assumptions

Hantushs method

Hantushs method

Hantushs method

where:a= major horizontal axisb= minor horizontal axisc= vertical axis (not used in this case)So, since the shape of equal drawdown is an ellipse in anisotropic aquifers we need to look at the equation of an ellipse in Cartesian coordinates is:

If we have one or more piezometers on a ray that froms an angle with the X axis, methods for isotropic aquifers can be applied to obtain values for (KD)e and S/(KD)n. Consequently, data is needed from more than one ray of piezometers to calculate S and (KD)n (Transmissivity along rays 0 to n originating at the pumped well, plotting all of these KDns corresponding to arrays 0 to n will make an ellipse shape). Hantushs MethodIf is defined as the angle between the first ray of piezometers (n = 1) and the X axis, and as the angle between the nth ray of pizometers and the first ray of piezometers (KD)n is given by:

Hantushs Method

Hantushs MethodMethod stated that when KDe, as, bs are known the other hydraulic characteristics can be calculated.Hence, it is not necessary to have values of S/(KD)n, provided that one has sufficient observations to draw the ellipses of equal drawdown. Hantush-Thomass MethodThe Hantush-Thomas method can be applied if the following assumptions and conditions are satisfied:- The assumptions listed at the beginning of Chapter 3, with the exception of the third assumption, which is replaced by:The aquifer is homogeneous, anisotropic on the horizontal plane, and of uniform thickness over the area influenced by the pumping test.The following condition is added:- The flow to the well is in unsteady state.

AssumptionsAs stated before, lines of equal drawdown in an isotropic aquifer are circular around the pumped well whereas the lines of equal drawdown in a horizontally anisotropic aquifer form ellipses. The equation of the an ellipses is:

Hantush-Thomass Method

The assumptions listed at the beginning of Chapter 3, with the exception of the third assumption, which is replaced by:The aquifer is homogeneous, anisotropic on the horizontal plane, and of uniform thickness over the area influenced by the pumping test.The following conditions are added:-The flow to the well is in an unsteady state;-The aquifer is penetrated by three wells, which are not on one ray. Two of them are pumped in sequence.

ConditionsWhere:as and bs are the principal axes of the ellipse of equal drawdown s at time Ts (Figure 8.1 C)It can be shown that:

Hantush-Thomass Method

NEUMANNS EXTENSION OF PAPADOPULOS METHOD

NEUMANNS EXTENSION OF PAPADOPULOS METHOD

NEUMANNS EXTENSION OF PAPADOPULOS METHOD

NEUMANNS EXTENSION OF PAPADOPULOS METHOD

In 1984, Neumann and others showed that the Papadopulos can be used with drawdown data from only three wells so long as two pumping test performed in sequence with two of the wells.

NEUMANNS EXTENSION OF PAPADOPULOS METHOD

HANTUSHS METHODThe flow to a well in a leaky aquifer which is anisotropic on the horizontal plane can be analyzed with a method that is essentially the same as the Hantush method for confined aquifers with anisotropy on the horizontal plane.

LEAKY AQUIFERS, ANISOTROPIC ON THE HORIZONTAL PLANE

The leakage factor, L, is unknown which is given by Hantush in

LEAKY AQUIFERS, ANISOTROPIC ON THE HORIZONTAL PLANE

c is constant so equation 8.7 gives the relationship between Ln and L1

The Hantush method can be applied if the following assumptions and conditions areThe assumptions listed at the beginning of Chapter 3, with the exception of the first and third assumptions, which are replaced by:The aquifer is leaky;The aquifer is homogeneous, anisotropic on the horizontal plane, and of uniform thickness over the area influenced by the pumping test.The following condition is added:The flow to the well is in an unsteady state.

LEAKY AQUIFERS, ANISOTROPIC ON THE HORIZONTAL PLANE

WEEKSS METHOD

CONFINED AQUIFERS, ANISOTROPIC ON THE VERTICAL PLANE

CONFINED AQUIFERS, ANISOTROPIC ON THE VERTICAL PLANE

CONFINED AQUIFERS, ANISOTROPIC ON THE VERTICAL PLANE

CONFINED AQUIFERS, ANISOTROPIC ON THE VERTICAL PLANE

Weekss Method

LEAKY AQUIFERS, ANISOTROPIC ON THE VERTICAL PLANE

Flow to a partially penetrating well in an unconfined aquifer is considered 3-D during the time the delayed watertable response occurs. 3-D flow is affected by anisotropy in the vertical plane. Neumanns curve fitting method from section 5.1.1 takes this anisotropy into account.

Two other methods can also be used that take vertical plane anisotropy into account when the well is partially penetrating:

Streltsovas curve-fitting method (Section 10.4.1) Neumans curve-fitting method (Section 10.4.2)Boulton-Streltsovas curve-fitting method (Section 11.2.1).

Unconfined aquifers, anisotropic on the vertical plane

Popular Tags:

Click here to load reader

Embed Size (px)
Recommended