Application Guide - Great Plains Manufacturing · 2/7/06 Application Guide 509-200M Great Plains...

© Copyright 1998 Printed

Manufacturing, Inc.www.greatplainsmfg.com

Read the Operator’s manual entirely. When you see this symbol, the subse-quent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!

Application Guide

10/4/2005 509-200M

!

Table of Contents

© Copyright 1998 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the informa-tion contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Great Plains Manufacturing, Incorporated TrademarksThe following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Great Plains Mfg., Inc.

Table of Contents

Application Guide 509-200M 2/7/06

Important Safety Information . . . . . . . . . . . . . . . . . 1Introduction & Technical Information . . . . . . . . . . . 3

Nozzle Spacing Conversion Factors . . . . . . . . . . 3Suggested Boom Heights . . . . . . . . . . . . . . . . . . 3Spraying Solutions Other Than Water . . . . . . . . . 3Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Calibration Procedures. . . . . . . . . . . . . . . . . . . . . 4Alternate Sprayer Calibration Method . . . . . . . . . 5Worn Nozzles & Flow Table Information . . . . . . 5Miles Per Hour Calibration . . . . . . . . . . . . . . . . . . 5TeeJet® Worn Nozzles & Flow Table . . . . . . . . . . 6MeterCone® Worn Nozzles & Flow Table . . . . . . 6MeterCone® Nozzles 15” Spacing (Height 12” to 13” or 24” to 26” Angle Fixed 20˚) . . . . . . . . . . 7MeterCone® Nozzles 20” Spacing (Height 19” to 21” Angle Fixed 20˚). . . . . . . . . . . . . . . . . . . . 10

MeterCone® Nozzles 30” Spacing (Height 24” to 26” Angle Fixed 20˚) . . . . . . . . . . . . . . . . . . . . 13Teejet® Nozzles 15” Spacing (Height 13” to 15” for XR80; 10” to 12” for XR110) . . . . . . . . 16TeeJet® Nozzles 20” Spacing (Height 17” to 19” for XR80; 15” to 18” for XR110) . . . . . . . . 19Teejet® Nozzles 30” Spacing (Height 26” to 28” for XR80; 20” to 22” for XR110) . . . . . . . . 22

Planter/Incorporation Kits . . . . . . . . . . . . . . . . . . . 25Great Plains Models AS-4, AS-6, & AS-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Incorporation Charts . . . . . . . . . . . . . . . . . . . . . . 26Custom Incorporation Chart . . . . . . . . . . . . . . . . 29Broadcasting Behind A Planter or Drill . . . . . . . . 30Banding Behind A Planter. . . . . . . . . . . . . . . . . . 31

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1

Important Safety Information

2/7/06 Application Guide 509-200M


!

Be Aware of Signal WordsThe word that designates a degree or level of hazard seriousness. The signal words are:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for func-tional purposes, cannot be guarded.

Indicates a potentially hazardous sit-uation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

Indicates a potentially hazardous sit-uation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

! DANGER!

! WARNING!

! CAUTION!


Handle Chemicals Properly▲ Read and follow Chemical Manu-

facturer’s instructions.▲ Protective clothing should be

worn.▲ Handle all chemicals with care. ▲ Agricultural chemicals can be

dangerous. Improper use can seriously injure persons, animals, plants, soil, and property.

▲ Inhaling smoke from any type of chemical fire is a serious health hazard.

▲ Store or dispose of unused chem-icals as specified by the chemical manufacturer.

▲ Before adding chemical to the tank, make sure tank is at least half full. Concentrate should not be poured into an empty tank.

▲ Never leave fill hose attached to the sprayer after filling tank. Chemicals in tank can siphon out of tank and contaminate freshwa-ter source.

▲ Always keep handwash tank filled with clean water and have soap available in case of an emergency. Flush any area of the body that is contaminated by chemicals imme-diately and thoroughly.

▲ Do not touch sprayer components with mouth or lips.

▲ If chemical is swallowed, carefully follow the chemical manufac-turer’s recommendations and con-sult with a doctor.

▲ If persons are exposed to a chem-ical in a way that could affect their health, consult a doctor immedi-ately with the chemical label or container in hand. Any delay could cause serious illness or death.

▲ Dispose of empty chemical con-tainers properly. By law rinsing of the used chemical container must be repeted three times. The con-tainer should then be punctured to prevent future use. An alternative is to jet-rinse or pressure rinse the container.

▲ Wash hands and face before eat-

ing when working with chemicals. Shower as soon as spraying is completed for the day.

▲ Spray only with acceptable wind conditions. Make sure wind drift of chemicals will not affect any sur-rounding land, people or animals.

▲ Never wash the sprayer tank out within 100 feet of any freshwater source or in a car wash.

▲ Rinse out the tank and spray rinse water on the last field sprayed.

Safety at All TimesThoroughly read and understand the instructions given in this manual and your operator’s manual before opera-tion. Refer to the “Important Safety Information” section in your operator’s manual.

2




▲ Waterproof apron

▲ Waterproof boots or foot cover-ings

▲ Waterproof, unlined gloves. Neo-prene gloves are recommended.

▲ Cloth coveralls/outer clothing changed daily; waterproof items if there is a chance of becoming wet with spray

▲ Waterproof, wide-brimmed hat

▲ Cartridge-type respirator ap-proved for pesticide vapors unless label specifies another type of respirator.

▲ Face shield, goggles or full face respirator. Goggles with side shields or a full face respirator is required if handling or applying dusts, wettable powders, or gran-ules or if being exposed to spray mist.

Personal Safety EquipmentGreat Plains advises all users of chemical pesticides or herbicides to use the following personal safety equip-ment. Always follow the chemical label instructions, operator safety and the effectivity of the product depends upon operator actions.

Wear Protective Equipment▲ Protective clothing and equipment

should be worn.▲ Do not wear contaminated cloth-

ing. Wash protective clothing and equipment with soap and water after each use. Personal clothing must be laundered separately from household articles.

▲ Clothing contaminated with cer-tain pesticides (read the label) must be destroyed according to state and local regulations.

▲ Wear clothing and equipment appropriate for the job. Avoid loose fitting clothing.

▲ Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hear-ing protection such as earmuffs or earplugs.

▲ Operating equipment safely requires the full attention of the operator. Avoid wearing radio headphones while operating machinery.

3

Introduction & Technical Information



Proper herbicide application is no longer something that can be taken lightly. Operator, crop, and environmental safety are a great concern not only for today’s agribusi-nessman but also his suburban neighbors. The Great Plains line of field sprayers are designed for farmers con-cerned about the effects they have on tomorrow’s agriculture.

Nozzle Spacing Conversion Factors

Where Tables are Based on 20" Nozzle Spacing

Other Spacing 8" 10" 12" 14" 16" 18" 22" 24" 30"

Conversion Factor 2.5 2 1.67 1.43 1.25 1.11 .91 .83 .66


Other Spacing 26" 28" 32" 34" 36" 38" 40" 42" 44"

Conversion Factor 1.15 1.07 .94 .88 .83 .79 .75 .71 .68


Other Spacing 28" 30" 32" 34" 36" 38" 42" 44" 48"

Conversion Factor 1.43 1.33 1.25 1.18 1.11 1.05 .95 .91 .83

Suggested Boom Heights

Nozzle Type

Nozzle Height

Spray Angle

15” Spacing

20” Spacing

30” Spacing

MeterCone™ 120 14-16” 19-21” 24-26”

XRTeeJet™ 80 13-15 17-19 26-28

XRTeejet™ 110 N/R 15-18 20-22

Spraying Solutions Other Than WaterCalculations are based on spraying water, which weighs 8.34 pounds per US gallon. The following conversion fac-tors must be used when spraying solutions which are heavier or lighter than water. In order to determine the proper size nozzle for the solution to be sprayed, multiply the desired GPM or GPA of solution by the water rate con-version factor. Then use the new converted GPM or GPA rate to select the proper size nozzle.

Weight of Solution{lbs/Gal.}

Solution Specific Gravity

Conversion Factor

7.00 .84 .92

7.50 .90 .95

8.00 .96 .98

8.34 {Water} 1.00 1.00

8.50 1.02 1.01

9.00 1.08 1.04

9.50 1.14 1.06

10.00 1.20 1.10

10.50 1.26 1.12

10.65 {Nitro-gen 28%}

1.28 1.13

11.00 1.32 1.15

11.50 1.38 1.18

12.00 1.44 1.20

14.00 1.68 1.30

EXAMPLE: It is desired to apply 22 GPA {gallons per acre} of nitrogen in 30" rows. {28% N, density is 10.65 lb/gal from the chart above}

GPA {Solution} x Conversion Factor = GPA

(22 gal/acre) (1.13) = 24.86 gal/acre

To choose a nozzle and a pressure, use 24.86 gal/acre on the nozzle charts.

ConversionsOPM to GPM ConversionOPM (Ounces Per Minute) + 128 = GPM (Gallons Per Minute)EXAMPLE: 32 OPM + 128 = .25 GPM

GPM to OPM ConversionGPM(Gallons Per Minute) x 128 = OPM(Ounces Per Minute)EXAMPLE: 0.5 GPM x 128 = 64 OPM

One Acre = 43,560 Square Feet = 0.405 Hectares

One Hectare = 2.471 Acres

One Gallon Per Acre = 9.35 Liters Per Hectare

One Mile = 5,280 Feet = 1,610 Meters = 1.61 Kilometers

One Gallon = 128 Fluid Ounces = 8 Pints = 4 Quarts

One Gallon = 3.79 Liters = 0.83 Imperial Gallons

One Pound Per Square Inch = 0.069 bar = 6.896 Kilopascal

One Mile Per Hour = 1.609 Kilometers Per Hour

Introduction & Technical Information

4

Calibration



ber of ounces caught is the exact number of gallons per acre you will apply with that perspective nozzle.

EXAMPLE #1: With a 20 inch spacing, it took 28 seconds to travel the 204 feet (refer to Table #1). Using a Meter-Cone™ 1.875 nozzle at 35 psi, the volume caught in 28 seconds was 21 ounces. This illustrates you would apply 21 gallons per acre with this nozzle.

EXAMPLE #2: With a 30 inch spacing, it took 15 seconds to travel 136 feet (refer to table #1). Using a TeeJet® XR11003 nozzle at 30 psi, the volume caught in 15 sec-onds was 13 ounces. This means you will apply 13 gallons per acre with the XR11003 nozzle at the same ground speed as when you drove the 136 feet.

Average Nozzle

Spacing (Inches)

Distance (Feet)

Average Nozzle

Spacing (Inches)

Distance (Feet)

6 681 22 186

8 510 24 170

10 408 30 136

12 340 36 113

14 292 38 107

15 272 40 102

16 255 42 97

18 227 48 85

20 204

Distance for each nozzle to spray 1/128 acre (One ounce discharge per nozzle equals one gallon per acre)

Calibration Procedures

! DANGER!Read and follow chemical manufacturer’s instructions. Some chemicals and cause serious burns, lung damage and even death.

This method gives you the distance driven to cover 1/128 acre (because there are 128 ounces per gallon). The time required to drive that distance is measured first, and the volume of spray in ounces caught in the time you mea-sured is your application rate in gallons per acre. From the chart below, determine the distance to drive in the field (three runs are suggested) to obtain your average time in seconds. You will generally use 15, 20, or 30 inch nozzle spacing on standard booms.

1. Determine your nozzle size, spacing, and pressure to achieve your desired rate from the application guide.

2. Measure the nozzle spacing on your boom and deter-mine the distance to drive to calibrate your sprayer

3. Mark off the distance with two markers, and time how many seconds it takes to drive this distance at the speed you will be spraying at. Make sure you are at spraying speed when you cross both marks. Two or more runs are suggested with the sprayer half full. Simulate your field conditions to take into account wheel slippage.

4. With the sprayer filled with water (no chemical added), park in an open area with the booms unfolded. Prepare to collect samples at the individual nozzles.Turn on the pump and run it at the operation pressure. Flip on the boom section switch(es) on the control box and catch the water being sprayed out of the nozzle(s) you are calibrating.

5. Measure the volume of the sample in ounces over the time it took to travel the distance in Step #3. The num-

Calibration

5

Calibration



Alternate Sprayer Calibration Method

To double check the accuracy of your Great Plains Sprayer, the following instructions provide another method of calibration:

Step 1: Measure 200 feet and determine the number of seconds required to travel this distance under field condi-tions with implements in working condition.

EXAMPLE: It takes 27 seconds to travel the 200 feet which equals 5 mph.

Step 2: Place graduated container or pre-weighed con-tainer under one nozzle and catch the discharge for 1 minute. Divide 128 into the number of fluid ounces caught. 128 fluid ounces equals one gallon.

EXAMPLE: 64 ounces caught in one minute.

64.0 ÷ 128 = 0.50 gallons/minute

Step 3: Net determine your nozzle spacing in inches.

EXAMPLE: 1 nozzle every 40".

SOLUTION:

Gallons per acre = 5940 x Gallon per minute Nozzle spacing in inches x Miles Per Hour

GPA = 5940 x .5040 x 5

GPA = 2970 200

GPA = 14.9

The above information will assure you of a check for accu-rate application in the event there is an error in the gauge nozzle spacing, nozzle height, tractor speed or nozzle wear.

Worn Nozzles & Flow Table Informa-tion1. Determine nozzle size and desired spraying pressure

using this application guide.

2. Find fluid ounces per minute (OPM) in tables on page 8.

3. Catch flow at pressure desired for 1 minute (for large nozzles catch the flow for 30 seconds and multiply by 2).

4. If the OPM caught are within the + limit in the chart on page 6, the nozzle is accurate and G.P.A. charts should be followed.

5. If the nozzle is not within the + limit, check for obstruc-tions or wear in the orifices of the nozzle. Take the cap off the nozzle, clean the orifices with a toothpick or brush and retest. If several nozzles test the same, but

are not within the + limits, a faulty gauge may be the problem. If two or more nozzles are outside the limit, it is a good indication that all your nozzles may be worn. In this case, it would be advisable to replace ALL the nozzles with new nozzles.

Miles Per Hour CalibrationTo determine true ground speed, use the table below with the sprayer half-filled with water.

When measuring the MPH of your tractor, always simulate current field conditions as close as possible, taking care to account for wheel slippage.

See application chart when M.P.H. is obtained.

mphSeconds to Travel 200 feet

mphSeconds to Travel 200 feet

2.5 55 7.0 19

3.0 45 8.0 17

3.5 39 9.0 15

4.0 34 10.0 14

4.5 30 11.0 12.5

5.0 27 12.0 11.5

6.0 23

6

Calibration



TeeJet® Worn Nozzles & Flow Table

MeterCone® Worn Nozzles & Flow Table

DISCARD NOZZLES NOT WITHIN THE + LIMITS OPM = Ounces Per Minute

NOTE: The + value shown is a +10% value of the OPM GPM = Gallons Per Minute

PSI8001 & 11001

80015 & 11015

8002 & 11002

8003 & 11003

8004 & 11004

8005 & 11005

8006 & 11006

8008 & 11008

GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM

15 .06 7.9+1 .09 11.5+1 .12 15.4+1 .18 23.0+1 .24 30.7+2 .31 39.7+2 .37 47.6+2 .49 62.7+3

20 .07 9.0+1 .11 14.1+1 .14 17.9+1 .21 26.9+1 .28 35.8+2 .35 44.8+2 .42 47.6+2 .57 73.0+4

25 .08 10.2+1 .12 15.4+1 .16 19.8+1 .24 30.1+2 .32 40.3+2 .39 49.9+3 .47 60.2+3 .63 80.6+4

30 .09 11.5+1 .13 16.6+1 .17 21.8+1 .26 33.3+2 .35 44.8+2 .43 55.0+3 .52 66.6+3 .69 88.3+4

35 .10 12.2+1 .14 17.9+1 .19 23.7+1 .28 35.8+2 .38 48.0+2 .47 59.5+3 .56 71.7+4 .75 95.4+5

40 .10 12.8+1 .15 19.2+1 .20 25.6+1 .30 38.4+2 .40 51.2+3 .50 64.0+3 .60 76.8+4 .80 102.4+5

45 .11 13.4+1 .16 20.2+1 .21 27.2+1 .32 40.6+2 .42 54.1+3 .53 67.5+3 .64 81.3+4 .85 108.2+5

50 .11 14.1+1 .17 21.1+1 .23 28.8+1 .34 42.9+2 .45 57.0+3 .56 71.0+4 .67 85.8+4 .89 113.9+6

55 .12 14.7+1 .17 22.1+1 .24 30.4+1 .35 45.1+2 .47 59.8+3 .58 74.6+4 .71 90.2+5 .94 119.7+6

60 .12 15.4+1 .18 23.0+1 .25 32.0+1 .37 47.4+2 .49 62.7+3 .61 78.1+4 .74 97.7+5 .98 125.4+6

DISCARD NOZZLES NOT WITHIN THE + LIMITS OPM = Ounces Per Minute

NOTE: The + value shown is a +10% value of the OPM GPM = Gallons Per Minute

PSIMC 1.25 MC 1.875 MC 2.5 MC 3.75 MC 5.0 MC 7.5 MC 10 MC 12.5 MC 15

GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM GPM OPM

10 .13 16.0+2 .19 24.0+2 .25 32.0+3 .38 48.0+5 .50 64.0+6 .75 96.5+9 1.00 128.0+13 1.25 160.0+16 1.50 192.0+19

15 .18 22.4+2 .23 29.1+3 .31 39.7+4 .46 58.6+6 .61 78.1+8 .92 117.8+12 1.22 156.2+15 1.53 195.8+20 1.84 235.5+23

20 .19 23.7+2 .26 33.0+3 .35 44.8+4 .53 67.5+6 .71 90.9+10 1.06 135.7+14 1.41 180.5+18 1.77 226.6+21 2.12 271.4+27

25 .20 25.0+2 .28 35.5+3 .40 51.2+5 .59 75.2+8 .79 101.1+10 1.19 152.3+15 1.57 201.0+20 1.98 253.4+25 2.37 303.4+30

30 .22 27.5+2 .33 41.9+4 .43 55.0+5 .65 82.9+8 .87 111.4+11 1.30 166.4+16 1.73 221.4+22 2.18 279.0+28 2.60 332.8+33

35 .23 28.8+2 .35 44.5+4 .46 58.9+6 .71 90.6+9 .92 117.8+12 1.39 177.9+18 1.85 236.8+24 2.31 295.7+30 2.78 355.8+35

40 .25 31.4+3 .38 48.3+5 .50 64.0+6 .75 95.7+9 1.0 128.0+13 1.50 192.0+19 2.00 256.0+25 2.50 320.0+32 3.00 384.0+38

45 .26 32.6+3 .39 50.9+5 .52 64.0+6 .79 101.5+10 1.06 135.5+13 --- --- --- --- --- --- --- ---

50 .28 35.2+3 .42 53.3+5 .56 65.3+6 .82 105.5+10 1.10 141.0+14 --- --- --- --- --- --- --- ---

55 .28 37.1+4 .43 55.7+5 .59 72.5+7 .87 111.9+11 1.16 149.0+15 --- --- --- --- --- --- --- ---

60 .31 39.0+4 .45 58.1+5 .61 78.1+8 .92 117.3+12 1.20 153.3+15 --- --- --- --- --- --- --- ---

7

Calibration



*For Post Emerge Applications where finer droplets are required use 40 PSI or greater.

MeterCone® Nozzles 15” Spacing (Height 12” to 13” or 24” to 26” Angle Fixed 20˚)

Nozzle Size

GPMPressure

PSIGallons Per Acre At Miles Per Hour

4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.25

.13 10.00 12.38 9.90 8.25 7.07 6.19 5.50 4.95 4.50 4.13

.17 15.00 17.33 13.86 11.55 9.90 8.66 7.70 6.93 6.30 5.78

.19 20.00 18.32 14.65 12.21 10.47 9.16 8.14 7.33 6.66 6.11

.20 25.00 19.31 15.44 12.87 11.03 9.65 8.58 7.72 7.02 6.44

.22 30.00 21.29 17.03 14.19 12.16 10.64 9.46 8.51 7.74 7.10

.23 35.00 22.28 17.82 14.85 12.73 11.14 9.90 8.91 8.10 7.43

.25 40.00* 24.26 19.40 16.17 13.86 12.13 10.78 9.70 8.82 8.09

.26 45.00* 25.25 20.20 16.83 14.43 12.62 11.22 10.10 9.18 8.42

.28 50.00* 27.23 21.78 18.15 15.56 13.61 12.10 10.89 9.90 9.08

.29 55.00* 28.71 22.97 19.14 16.41 14.36 12.76 11.48 10.44 9.57

.31 60.00* 30.20 24.16 20.13 17.25 15.10 13.42 12.08 10.98 10.07

Nozzle Size

GPMPressure

PSI

Gallons Per Acre At Miles Per Hour

4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

2.5

.25 10.00 24.75 19.80 16.50 14.14 12.38 11.00 9.90 9.00 8.25

.31 15.00 30.69 24.55 20.46 17.54 15.35 13.64 12.28 11.16 10.23

.35 20.00 34.65 27.72 23.10 19.80 17.33 15.40 13.86 12.60 11.55

.40 25.00 39.60 31.68 26.40 22.63 19.80 17.60 15.84 14.40 13.20

.43 30.00 42.57 34.06 28.38 24.33 21.29 18.92 17.03 15.48 14.19

.46 35.00 45.54 36.43 30.36 26.02 22.77 20.24 18.22 16.56 15.18

.50 40.00* 49.50 39.60 33.00 28.29 24.75 22.00 19.80 18.00 16.50

.52 45.00* 51.08 40.87 34.06 29.19 25.54 22.70 20.43 18.58 17.03

.56 50.00* 55.64 44.51 37.09 31.79 27.82 24.73 22.26 20.23 18.55

.59 55.00* 58.41 46.73 38.94 33.38 29.21 25.96 23.36 21.24 19.47

.61 60.00* 60.39 48.31 40.26 34.51 30.20 26.84 24.16 21.96 20.13

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.875

.19 10.00 18.56 14.85 12.38 10.61 9.28 8.25 7.43 6.75 6.19

.23 15.00 22.52 18.02 15.02 12.87 11.26 10.01 9.01 8.19 7.51

.26 20.00 25.49 20.39 17.00 14.57 12.75 11.33 10.20 9.27 8.50

.28 25.00 27.47 21.98 18.32 15.70 13.74 12.21 10.99 9.99 9.16

.33 30.00 32.42 25.94 21.62 18.53 16.21 14.41 12.97 11.79 10.81

.35 35.00 34.40 27.52 22.94 19.66 17.20 15.29 13.76 12.51 11.47

.38 40.00* 37.37 29.90 24.92 21.36 18.69 16.61 14.95 13.59 12.46

.39 45.00* 40.59 32.47 27.06 23.19 20.30 18.04 16.24 14.76 13.53

.42 50.00* 43.56 34.85 29.04 24.89 21.78 19.36 17.42 15.84 14.52

.43 55.00* 46.53 37.22 31.02 26.59 23.27 20.68 18.61 16.92 15.51

.45 60.00* 50.49 40.39 33.66 28.85 25.25 22.44 20.20 18.36 16.83

8

Calibration





Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

3.75

.38 10.00 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.46 15.00 45.29 36.23 30.20 25.88 22.65 20.13 18.12 16.47 15.10

.53 20.00 52.22 41.78 34.82 29.84 26.11 23.21 20.89 18.99 17.41

.59 25.00 58.16 46.53 38.78 33.24 29.08 25.85 23.27 21.15 19.39

.65 30.00 64.10 51.28 42.74 36.63 32.05 28.49 25.64 23.31 21.37

.71 35.00 70.04 56.03 46.70 40.02 35.02 31.13 28.02 25.47 23.35

.75 40.00* 74.00 59.20 49.34 42.29 37.00 32.89 29.60 26.91 24.67

.79 45.00* 80.19 64.15 53.46 45.82 40.10 35.64 32.08 29.16 26.73

.82 50.00* 85.14 68.11 56.76 48.65 42.57 37.84 34.06 30.96 28.38

.87 55.00* 91.08 72.86 60.72 52.05 45.54 40.48 36.43 33.12 30.36

.92 60.00* 97.02 77.62 64.68 55.44 48.51 43.12 38.81 35.28 32.34

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

5.0

.50 10.00 49.50 39.60 33.00 28.29 24.75 22.00 19.80 18.00 16.50

.61 15.00 60.39 48.31 40.26 34.51 30.20 26.84 24.16 21.96 20.13

.71 20.00 70.29 56.23 46.86 40.17 35.15 31.24 28.12 25.56 23.43

.79 25.00 78.21 62.57 52.14 44.69 39.11 34.76 31.28 28.44 26.07

.87 30.00 86.13 68.90 57.42 49.22 43.07 38.28 34.45 31.32 28.71

.92 35.00 91.08 72.86 60.72 52.05 45.54 40.48 36.43 33.12 30.361.00 40.00* 99.00 79.20 66.00 56.57 49.50 44.00 39.60 36.00 33.00

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

7.5

.75 10.00 74.25 59.40 49.50 42.43 37.13 33.00 29.70 27.00 24.75

.92 15.00 91.08 72.86 60.72 52.05 45.54 40.48 36.43 33.12 30.36

1.06 20.00 104.94 83.95 69.96 59.97 52.47 46.64 41.98 38.16 34.98

1.19 25.00 117.81 94.25 78.54 67.32 58.91 52.36 47.12 42.84 39.27

1.30 30.00 128.70 102.96 85.80 73.54 64.35 57.20 51.48 46.80 42.90

1.39 35.00 137.61 110.09 91.74 78.63 68.81 61.16 55.04 50.04 45.87

1.50 40.00* 148.50 118.80 99.00 84.86 74.25 66.00 59.40 54.00 49.50

9

Calibration




Nozzle Size

GPM PressurePSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

10.0

1.00 10.00 99.00 79.20 66.00 56.57 49.50 44.00 39.60 36.00 33.001.22 15.00 120.78 96.62 80.52 69.02 60.39 53.68 48.31 43.92 40.261.41 20.00 139.59 111.67 93.06 79.77 69.80 62.04 55.84 50.76 46.531.57 25.00 155.43 124.34 103.62 88.82 77.72 69.08 62.17 56.52 51.811.73 30.00 171.27 137.02 114.18 97.87 85.64 76.12 68.51 62.28 57.091.85 35.00 183.15 146.52 122.10 104.66 91.58 81.40 73.26 66.60 61.052.0 40.00* 198.00 158.40 132.00 113.14 99.00 88.00 79.20 72.00 66.00

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

12.5

1.25 10.00 123.75 99.00 82.50 70.71 61.88 55.00 49.50 45.00 41.251.53 15.00 151.47 121.18 100.98 86.55 75.74 67.32 60.59 55.08 50.491.77 20.00 175.23 140.18 116.82 100.13 87.62 77.88 70.09 63.72 58.411.98 25.00 196.02 156.82 130.68 112.01 98.01 87.12 78.41 71.28 65.342.18 30.00 215.82 172.66 143.88 123.33 107.91 95.92 86.33 78.48 71.942.31 35.00 228.69 182.95 152.46 130.68 114.35 101.64 91.48 83.16 76.232.50 40.00* 247.50 198.00 165.00 141.43 123.75 110.00 99.00 90.00 82.50

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

15.0

1.50 10.00 148.50 118.80 99.00 84.86 74.25 66.00 59.40 54.00 49.501.84 15.00 182.16 145.73 121.44 104.09 91.08 80.96 72.86 66.24 60.722.12 20.00 209.88 167.90 139.92 119.93 104.94 93.28 83.95 76.32 69.962.37 25.00 234.63 187.70 156.42 134.07 117.32 104.28 93.85 85.32 78.212.60 30.00 257.40 205.92 171.60 147.09 128.70 114.40 102.96 93.60 85.802.78 35.00 275.22 220.18 183.48 157.27 137.61 122.32 110.09 100.08 91.743.00 40.00* 297.00 237.60 198.00 169.71 148.50 132.00 118.80 108.00 99.00

10

Calibration



Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

2.5

.25 10.00 18.56 14.85 12.38 10.61 9.28 8.25 7.43 6.75 6.19

.31 15.00 23.02 18.41 15.35 13.15 11.51 10.23 9.21 8.37 7.67

.35 20.00 25.99 20.79 17.33 14.85 12.99 11.55 10.40 9.45 8.66

.40 25.00 29.70 23.76 19.80 16.97 14.85 13.20 11.88 10.80 9.90

.43 30.00 31.93 25.54 21.29 18.24 15.96 14.19 12.77 11.61 10.64

.46 35.00 34.16 27.32 22.77 19.52 17.08 15.18 13.66 12.42 11.39

.50 40.00* 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.52 45.00* 38.31 30.65 25.54 21.89 19.16 17.03 15.33 13.93 12.77

.56 50.00* 41.73 33.38 27.82 23.84 20.86 18.55 16.69 15.17 13.91

.59 55.00* 43.81 35.05 29.21 25.03 21.90 19.47 17.52 15.93 14.60

.61 60.00* 45.29 36.23 30.20 25.88 22.65 20.13 18.12 16.47 15.10


MeterCone® Nozzles 20” Spacing (Height 19” to 21” Angle Fixed 20˚)

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.25

.13 10.00 9.28 7.43 6.19 5.30 4.64 4.13 3.71 3.38 3.09

.17 15.00 12.99 10.40 8.66 7.43 6.50 5.78 5.20 4.73 4.33

.19 20.00 13.74 10.99 9.16 7.85 6.87 6.11 5.49 5.00 4.58

.20 25.00 14.48 11.58 9.65 8.27 7.24 6.44 5.79 5.27 4.83

.22 30.00 15.96 12.77 10.64 9.12 7.98 7.10 6.39 5.81 5.32

.23 35.00 16.71 13.37 11.14 9.55 8.35 7.43 6.68 6.08 5.57

.25 40.00* 18.19 14.55 12.13 10.40 9.10 8.09 7.28 6.62 6.06

.26 45.00* 18.93 15.15 12.62 10.82 9.47 8.42 7.57 6.89 6.31

.28 50.00* 20.42 16.34 13.61 11.67 10.21 9.08 8.17 7.43 6.81

.29 55.00* 21.53 17.23 14.36 12.30 10.77 9.57 8.61 7.83 7.18

.31 60.00* 22.65 18.12 15.10 12.94 11.32 10.07 9.06 8.24 7.55

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.875

.19 10.00 13.92 11.14 9.28 7.96 6.96 6.19 5.57 5.06 4.64

.23 15.00 16.89 13.51 11.26 9.65 8.45 7.51 6.76 6.14 5.63

.26 20.00 19.12 15.30 12.75 10.93 9.56 8.50 7.65 6.95 6.37

.28 25.00 20.60 16.48 13.74 11.77 10.30 9.16 8.24 7.49 6.87

.33 30.00 24.32 19.45 16.21 13.90 12.16 10.81 9.73 8.84 8.11

.35 35.00 25.80 20.64 17.20 14.74 12.90 11.47 10.32 9.38 8.60

.38 40.00* 28.03 22.42 18.69 16.02 14.01 12.46 11.21 10.19 9.34

.39 45.00* 30.44 24.35 20.30 17.40 15.22 13.53 12.18 11.07 10.15

.42 50.00* 32.67 26.14 21.78 18.67 16.34 14.52 13.07 11.88 10.89

.43 55.00* 34.90 27.92 23.27 19.94 17.45 15.51 13.96 12.69 11.63

.45 60.00* 37.87 30.29 25.25 21.64 18.93 16.83 15.15 13.77 12.62

11

Calibration





Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

3.75

.38 10.00 27.84 22.28 18.56 15.91 13.92 12.38 11.14 10.13 9.28

.46 15.00 33.97 27.18 22.65 19.41 16.98 15.10 13.59 12.35 11.32

.53 20.00 39.17 31.33 26.11 22.38 19.58 17.41 15.67 14.24 13.06

.59 25.00 43.62 34.90 29.08 24.93 21.81 19.39 17.45 15.86 14.54

.65 30.00 48.08 38.46 32.05 27.47 24.04 21.37 19.23 17.48 16.03

.71 35.00 52.53 42.03 35.02 30.02 26.27 23.35 21.01 19.10 17.51

.75 40.00* 55.50 44.40 37.00 31.72 27.75 24.67 22.20 20.18 18.50

.79 45.00* 60.14 48.11 40.10 34.37 30.07 26.73 24.06 21.87 20.05

.82 50.00* 63.86 51.08 42.57 36.49 31.93 28.38 25.54 23.22 21.29

.87 55.00* 68.31 54.65 45.54 39.03 34.16 30.36 27.32 24.84 22.77

.92 60.00* 72.77 58.21 48.51 41.58 36.38 32.34 29.11 26.46 24.26

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

5.0

.50 10.00 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.61 15.00 45.29 36.23 30.20 25.88 22.65 20.13 18.12 16.47 15.10

.71 20.00 52.72 42.17 35.15 30.12 26.36 23.43 21.09 19.17 17.57

.79 25.00 58.66 46.93 39.11 33.52 29.33 26.07 23.46 21.33 19.55

.87 30.00 64.60 51.68 43.07 36.91 32.30 28.71 25.84 23.49 21.53

.92 35.00 68.31 54.65 45.54 39.03 34.16 30.36 27.32 24.84 22.771.00 40.00* 74.25 59.40 49.50 42.43 37.13 33.00 29.70 27.00 24.75

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

7.5

.75 10.00 55.69 44.55 37.13 31.82 27.84 24.75 22.28 20.25 18.56

.92 15.00 68.31 54.65 45.54 39.03 34.16 30.36 27.32 24.84 22.77

1.06 20.00 78.71 62.96 52.47 44.97 39.35 34.98 31.48 28.62 26.241.19 25.00 88.36 70.69 58.91 50.49 44.18 39.27 35.34 32.13 29.451.30 30.00 96.53 77.22 64.35 55.16 48.26 42.90 38.61 35.10 32.181.39 35.00 103.21 82.57 68.81 58.98 51.60 45.87 41.28 37.53 34.401.50 40.00* 111.38 89.10 74.25 63.64 55.69 49.50 44.55 40.50 37.13

12

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

10.0

1.00 10.00 74.25 59.40 49.50 42.43 37.13 33.00 29.70 27.00 24.751.22 15.00 90.59 72.47 60.39 51.76 45.29 40.26 36.23 32.94 30.201.41 20.00 104.69 83.75 69.80 59.82 52.35 46.53 41.88 38.07 34.901.57 25.00 116.57 93.26 77.72 66.61 58.29 51.81 46.63 42.39 38.861.73 30.00 128.45 102.76 85.64 73.40 64.23 57.09 51.38 46.71 42.821.85 35.00 137.36 109.89 91.58 78.49 68.68 61.05 54.95 49.95 45.792.0 40.00* 148.50 118.80 99.00 84.86 74.25 66.00 59.40 54.00 49.50

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

12.5

1.25 10.00 92.81 74.25 61.88 53.04 46.41 41.25 37.13 33.75 30.941.53 15.00 113.60 90.88 75.74 64.92 56.80 50.49 45.44 41.31 37.871.77 20.00 131.42 105.14 87.62 75.10 65.71 58.41 52.57 47.79 43.811.98 25.00 147.02 117.61 98.01 84.01 73.51 65.34 58.81 53.46 49.012.18 30.00 161.87 129.49 107.91 92.49 80.93 71.94 64.75 58.86 53.962.31 35.00 171.52 137.21 114.35 98.01 85.76 76.23 68.61 62.37 57.172.50 40.00* 185.63 148.50 123.75 106.07 92.81 82.50 74.25 67.50 61.88

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

15.0

1.50 10.00 111.38 89.10 74.25 63.64 55.69 49.50 44.55 40.50 37.131.84 15.00 136.62 109.30 91.08 78.07 68.31 60.72 54.65 49.68 45.542.12 20.00 157.41 125.93 104.94 89.95 78.71 69.96 62.96 57.24 52.472.37 25.00 175.97 140.78 117.32 100.56 87.99 78.21 70.39 63.99 58.662.60 30.00 193.05 154.44 128.70 110.31 96.53 85.80 77.22 70.20 64.352.78 35.00 206.42 165.13 137.61 117.95 103.21 91.74 82.57 75.06 68.813.00 40.00* 222.75 178.20 148.50 127.29 111.38 99.00 89.10 81.00 74.25

13

Calibration





Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.875

.19 10.00 9.28 7.43 6.19 5.30 4.64 4.13 3.71 3.38 3.09

.23 15.00 11.26 9.01 7.51 6.44 5.63 5.01 4.50 4.10 3.75

.26 20.00 12.75 10.20 8.50 7.28 6.37 5.67 5.10 4.64 4.25

.28 25.00 13.74 10.99 9.16 7.85 6.87 6.11 5.49 5.00 4.58

.33 30.00 16.21 12.97 10.81 9.26 8.11 7.21 6.48 5.90 5.40

.35 35.00 17.20 13.76 11.47 9.83 8.60 7.65 6.88 6.26 5.73

.38 40.00* 18.69 14.95 12.46 10.68 9.34 8.31 7.47 6.80 6.23

.39 45.00* 20.30 16.24 13.53 11.60 10.15 9.02 8.12 7.38 6.77

.42 50.00* 21.78 17.42 14.52 12.45 10.89 9.68 8.71 7.92 7.26

.43 55.00* 23.27 18.61 15.51 13.29 11.63 10.34 9.31 8.46 7.76

.45 60.00* 25.25 20.20 16.83 14.43 12.62 11.22 10.10 9.18 8.42

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

2.5

.25 10.00 12.38 9.90 8.25 7.07 6.19 5.50 4.95 4.50 4.13

.31 15.00 15.35 12.28 10.23 8.77 7.67 6.82 6.14 5.58 5.12

.35 20.00 17.33 13.86 11.55 9.90 8.66 7.70 6.93 6.30 5.78

.40 25.00 19.80 15.84 13.20 11.31 9.90 8.80 7.92 7.20 6.60

.43 30.00 21.29 17.03 14.19 12.16 10.64 9.46 8.51 7.74 7.10

.46 35.00 22.77 18.22 15.18 13.01 11.39 10.12 9.11 8.28 7.59

.50 40.00* 24.75 19.80 16.50 14.14 12.38 11.00 9.90 9.00 8.25

.52 45.00* 25.54 20.43 17.03 14.60 12.77 11.35 10.22 9.29 8.51

.56 50.00* 27.82 22.26 18.55 15.90 13.91 12.36 11.13 10.12 9.27

.59 55.00* 29.21 23.36 19.47 16.69 14.60 12.98 11.68 10.62 9.74

.61 60.00* 30.20 24.16 20.13 17.25 15.10 13.42 12.08 10.98 10.07

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

1.25

.13 10.00 6.19 4.95 4.13 3.54 3.09 2.75 2.48 2.25 2.06

.17 15.00 8.66 6.93 5.78 4.95 4.33 3.85 3.47 3.15 2.89

.19 20.00 9.16 7.33 6.11 5.23 4.58 4.07 3.66 3.33 3.05..20 25.00 9.65 7.72 6.44 5.52 4.83 4.29 3.86 3.51 3.22.22 30.00 10.64 8.51 7.10 6.08 5.32 4.73 4.26 3.87 3.55.23 35.00 11.14 8.91 7.43 6.36 5.57 4.95 4.46 4.05 3.71.25 40.00* 12.13 9.70 8.09 6.93 6.06 5.39 4.85 4.41 4.04.26 45.00* 12.62 10.10 8.42 7.21 6.31 5.61 5.05 4.59 4.21.28 50.00* 13.61 10.89 9.08 7.78 6.81 6.05 5.45 4.95 4.54.29 55.00* 14.36 11.48 9.57 8.20 7.18 6.38 5.74 5.22 4.79.31 60.00* 15.10 12.08 10.07 8.63 7.55 6.71 6.04 5.49 5.03

14

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

3.75

.38 10.00 18.56 14.85 12.38 10.61 9.28 8.25 7.43 6.75 6.19

.46 15.00 22.65 18.12 15.10 12.94 11.32 10.07 9.06 8.24 7.55

.53 20.00 26.11 20.89 17.41 14.92 13.06 11.61 10.44 9.50 8.70

.59 25.00 29.08 23.27 19.39 16.62 14.54 12.93 11.63 10.58 9.69

.65 30.00 32.05 25.64 21.37 18.32 16.03 14.25 12.82 11.66 10.68

.71 35.00 35.02 28.02 23.35 20.01 17.51 15.57 14.01 12.74 11.67

.75 40.00* 37.00 29.60 24.67 21.14 18.50 16.45 14.80 13.46 12.33

.79 45.00* 40.10 32.08 26.73 22.91 20.05 17.82 16.04 14.58 13.37

.82 50.00* 42.57 34.06 28.38 24.33 21.29 18.92 17.03 15.48 14.19

.87 55.00* 45.54 36.43 30.36 26.02 22.77 20.24 18.22 16.56 15.18

.92 60.00* 48.51 38.81 32.34 27.72 24.26 21.56 19.40 17.64 16.17

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

5.0

.50 10.00 24.75 19.80 16.50 14.14 12.38 11.00 9.90 9.00 8.25

.61 15.00 30.20 24.16 20.13 17.25 15.10 13.42 12.08 10.98 10.07

.71 20.00 35.15 28.12 23.43 20.08 17.57 15.62 14.06 12.78 11.72

.79 25.00 39.11 31.28 26.07 22.35 19.55 17.38 15.64 14.22 13.04

.87 30.00 43.07 34.45 28.71 24.61 21.53 19.14 17.23 15.66 14.36

.92 35.00 45.54 36.43 30.36 26.02 22.77 20.24 18.22 16.56 15.181.00 40.00* 49.50 39.60 33.00 28.29 24.75 22.00 19.80 18.00 16.50

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

7.5

.75 10.00 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.92 15.00 45.54 36.43 30.36 26.02 22.77 20.24 18.22 16.56 15.181.06 20.00 52.47 41.98 34.98 29.98 26.24 23.32 20.99 19.08 17.491.19 25.00 58.91 47.12 39.27 33.66 29.45 26.18 23.56 21.42 19.641.30 30.00 64.35 51.48 42.90 36.77 32.18 28.60 25.74 23.40 21.451.39 35.00 68.81 55.04 45.87 39.32 34.40 30.58 27.52 25.02 22.941.50 40.00* 74.25 59.40 49.50 42.43 37.13 33.00 29.70 27.00 24.75

15

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

10.0

1.00 10.00 49.50 39.60 33.00 28.29 24.75 22.00 19.80 18.00 16.501.22 15.00 60.39 48.31 40.26 34.51 30.20 26.84 24.16 21.96 20.131.41 20.00 69.80 55.84 46.53 39.88 34.90 31.02 27.92 25.38 23.271.57 25.00 77.72 62.17 51.81 44.41 38.86 34.54 31.09 28.26 25.911.73 30.00 85.64 68.51 57.09 48.93 42.82 38.06 34.25 31.14 28.551.85 35.00 91.58 73.26 61.05 52.33 45.79 40.70 36.63 33.30 30.532.0 40.00* 99.00 79.20 66.00 56.57 49.50 44.00 39.60 36.00 33.00

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

12.5

1.25 10.00 61.88 49.50 41.25 35.36 30.94 27.50 24.75 22.50 20.631.53 15.00 75.74 60.59 50.49 43.28 37.87 33.66 30.29 27.54 25.251.77 20.00 87.62 70.09 58.41 50.07 43.81 38.94 35.05 31.86 29.211.98 25.00 98.01 78.41 65.34 56.01 49.01 43.56 39.20 35.64 32.672.18 30.00 107.91 86.33 71.94 61.66 53.96 47.96 43.16 39.24 35.972.31 35.00 114.35 91.48 76.23 65.34 57.17 50.82 45.74 41.58 38.122.50 40.00* 123.75 99.00 82.50 70.71 61.88 55.00 49.50 45.00 41.25

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

15.0

1.50 10.00 74.25 59.40 49.50 42.43 37.13 33.00 29.70 27.00 24.751.84 15.00 91.08 72.86 60.72 52.05 45.54 40.48 36.43 33.12 30.362.12 20.00 104.94 83.95 69.96 59.97 52.47 46.64 41.98 38.16 34.982.37 25.00 117.32 93.85 78.21 67.04 58.66 52.14 46.93 42.66 39.112.60 30.00 128.70 102.96 85.80 73.54 64.35 57.20 51.48 46.80 42.902.78 35.00 137.61 110.09 91.74 78.63 68.81 61.16 55.04 50.04 45.873.00 40.00* 148.50 118.80 99.00 84.86 74.25 66.00 59.40 54.00 49.50

16

Calibration



Teejet® Nozzles 15” Spacing (Height 13” to 15” for XR80; 10” to 12” for XR110)

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8001

&XR

11001

.06 15.00 5.94 4.75 3.96 3.39 2.97 2.64 2.38 2.16 1.98

.07 20.00 6.93 5.54 4.62 3.96 3.47 3.08 2.77 2.52 2.31

.08 25.00 7.92 6.34 5.28 4.53 3.96 3.52 3.17 2.88 2.64

.09 30.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

.10 35.00 9.41 7.52 6.27 5.37 4.70 4.18 3.76 3.42 3.14

.10 40.00 9.90 7.92 6.60 5.66 4.95 4.40 3.96 3.60 3.30

.11 45.00 10.40 8.32 6.93 5.94 5.20 4.62 4.16 3.78 3.47

.11 50.00 10.89 8.71 7.26 6.22 5.45 4.84 4.36 3.96 3.63

.12 55.00 11.39 9.11 7.59 6.51 5.69 5.06 4.55 4.14 3.80

.12 60.00 11.88 9.50 7.92 6.79 5.94 5.28 4.75 4.32 3.96

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR80015

&XR

11015

.09 15.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

.11 20.00 10.89 8.71 7.26 6.22 5.45 4.84 4.36 3.96 3.63

.12 25.00 11.88 9.50 7.92 6.79 5.94 5.28 4.75 4.32 3.96

.13 30.00 12.87 10.30 8.58 7.35 6.44 5.72 5.15 4.68 4.29

.14 35.00 13.86 11.09 9.24 7.92 6.93 6.16 5.54 5.04 4.62

.15 40.00 14.85 11.88 9.90 8.49 7.43 6.60 5.94 5.40 4.95

.16 45.00 15.59 12.47 10.40 8.91 7.80 6.93 6.24 5.67 5.20

.17 50.00 16.34 13.07 10.89 9.33 8.17 7.26 6.53 5.94 5.45

.17 55.00 17.08 13.66 11.39 9.76 8.54 7.59 6.83 6.21 5.69

.18 60.00 17.82 14.26 11.88 10.18 8.91 7.92 7.13 6.48 5.94

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8002

&XR

11002

.12 15.00 11.88 9.50 7.92 6.79 5.94 5.28 4.75 4.32 3.96

.14 20.00 13.86 11.09 9.24 7.92 6.93 6.16 5.54 5.04 4.62

.16 25.00 15.35 12.28 10.23 8.77 7.67 6.82 6.14 5.58 5.12

.17 30.00 16.83 13.46 11.22 9.62 8.42 7.48 6.73 6.12 5.61

.19 35.00 18.32 14.65 12.21 10.47 9.16 8.14 7.33 6.66 6.11

.20 40.00 19.80 15.84 13.20 11.31 9.90 8.80 7.92 7.20 6.60

.21 45.00 21.04 16.83 14.03 12.02 10.52 9.35 8.42 7.65 7.01

.23 50.00 22.28 17.82 14.82 12.73 11.14 9.90 8.91 8.10 7.43

.24 55.00 23.51 18.81 15.68 13.44 11.76 10.45 9.41 8.55 7.84

.25 60.00 24.75 19.80 16.50 14.14 12.38 11.00 9.90 9.00 8.25

17

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8003

&XR

11003

.18 15.00 17.82 14.26 11.88 10.18 8.91 7.92 7.13 6.48 5.94

.21 20.00 20.79 16.63 13.86 11.88 10.40 9.24 8.32 7.56 6.93

.24 25.00 23.27 18.61 15.51 13.29 11.63 10.34 9.31 8.46 7.76

.26 30.00 25.74 20.59 17.16 14.71 12.87 11.44 10.30 9.36 8.58

.28 35.00 27.72 22.18 18.48 15.84 13.86 12.32 11.09 10.08 9.24

.30 40.00 29.70 23.76 19.80 16.97 14.85 13.20 11.88 10.80 9.90

.32 45.00 31.43 25.15 20.96 17.96 15.72 13.97 12.57 11.43 10.48

.34 50.00 33.17 26.53 22.11 18.95 16.58 14.74 13.27 12.06 11.06

.35 55.00 34.90 27.92 23.27 19.94 17.45 15.51 13.96 12.69 11.63

.37 60.00 36.63 29.30 24.42 20.93 18.32 16.28 14.65 13.32 12.21

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8004

&XR

11004

.24 15.00 23.76 19.01 15.84 13.58 11.88 10.56 9.50 8.64 7.92

.28 20.00 27.72 22.18 18.48 15.84 13.86 12.32 11.09 10.08 9.24

.32 25.00 31.19 24.95 20.79 17.82 15.59 13.86 12.47 11.34 10.40

.35 30.00 34.65 27.72 23.10 19.80 17.33 15.40 13.86 12.60 11.55

.38 35.00 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.40 40.00 39.60 31.68 26.40 22.63 19.80 17.60 15.84 14.40 13.20

.42 45.00 41.83 33.46 27.89 23.90 20.91 18.59 16.73 15.21 13.94

.45 50.00 44.06 35.24 29.37 25.17 22.03 19.58 17.62 16.02 14.69

.47 55.00 46.28 37.03 30.86 26.45 23.14 20.57 18.51 16.83 15.43

.49 60.00 48.51 38.81 32.34 27.72 24.26 21.56 19.40 17.64 16.17

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8005

&XR

11005

.31 15.00 30.69 24.55 20.46 17.54 15.35 13.64 12.28 11.16 10.23

.35 20.00 34.65 27.72 23.10 19.80 17.33 15.40 13.86 12.60 11.55

.39 25.00 38.61 30.89 25.74 22.06 19.31 17.16 15.44 14.04 12.87

.43 30.00 42.57 34.06 28.38 24.33 21.29 18.92 17.03 15.48 14.19

.47 35.00 46.04 36.83 30.69 26.31 23.02 20.46 18.41 16.74 15.35

.50 40.00 49.50 39.60 33.00 28.29 24.75 22.00 19.80 18.00 16.50

.53 45.00 52.22 41.78 34.82 29.84 26.11 23.21 20.89 18.99 17.41

.56 50.00 54.95 43.96 36.63 31.40 27.47 24.42 21.98 19.98 18.32

.58 55.00 57.67 46.13 38.45 32.95 28.83 25.63 23.07 20.97 19.22

.61 60.00 60.39 48.31 40.26 34.51 30.20 26.84 24.16 21.96 20.13

18

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8006

&XR

11006

.37 15.00 36.63 29.30 24.42 20.93 18.32 16.28 14.65 13.32 12.21

.42 20.00 41.58 33.26 27.72 23.76 20.79 18.48 16.63 15.12 13.86

.47 25.00 46.53 37.22 31.02 26.59 23.27 20.68 18.61 16.92 15.51

.52 30.00 51.48 41.18 34.32 29.42 25.74 22.88 20.59 18.72 17.16

.56 35.00 55.44 44.35 36.96 31.68 27.72 24.64 22.18 20.16 18.48

.60 40.00 59.40 47.52 39.60 33.94 29.70 26.40 23.76 21.60 19.80

.64 45.00 62.87 50.29 41.91 35.92 31.43 27.94 25.15 22.86 20.96

.67 50.00 66.33 53.06 44.22 37.90 33.17 29.48 26.53 24.12 22.11

.71 55.00 69.80 55.84 46.53 39.88 34.90 31.02 27.92 25.38 23.27

.74 60.00 73.26 58.61 48.84 41.86 36.63 32.56 29.30 26.64 24.42

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8008

&XR

11008

.49 15.00 48.51 38.81 32.34 27.72 24.26 21.56 19.40 17.64 16.17

.57 20.00 56.43 45.14 37.62 32.25 28.22 25.08 22.57 20.52 18.81

.63 25.00 62.37 49.90 41.58 35.64 31.19 27.72 24.95 22.68 20.79

.69 30.00 68.31 54.65 45.54 39.03 34.16 30.36 27.32 24.84 22.77

.75 35.00 73.76 59.00 49.17 42.15 36.88 32.78 29.50 26.82 24.59

.80 40.00 79.20 63.36 52.80 45.26 39.60 35.20 31.68 28.80 26.40

.85 45.00 83.66 66.92 55.77 47.80 41.83 37.18 33.46 30.42 27.89

.89 50.00 88.11 70.94 58.74 50.35 44.06 39.16 35.24 32.04 29.37

.94 55.00 92.57 74.05 61.71 52.89 46.28 41.14 37.03 33.66 30.86

.98 60.00 97.02 77.62 64.68 55.44 48.51 43.12 38.81 35.28 32.34

19

Calibration



TeeJet® Nozzles 20” Spacing (Height 17” to 19” for XR80; 15” to 18” for XR110)

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8001

&XR

11001

.06 15.00 4.46 3.56 2.97 2.55 2.23 1.98 1.78 1.62 1.49

.07 20.00 5.20 4.16 3.47 2.97 2.60 2.31 2.08 1.89 1.73

.08 25.00 5.94 4.75 3.96 3.39 2.97 2.64 2.38 2.16 1.98

.09 30.00 6.68 5.35 4.46 3.82 3.34 2.97 2.67 2.43 2.23

.10 35.00 7.05 5.64 4.70 4.03 3.53 3.14 2.82 2.57 2.35

.10 40.00 7.43 5.94 4.95 4.24 3.71 3.30 2.97 2.70 2.48

.11 45.00 7.80 6.24 5.20 4.46 3.90 3.47 3.12 2.84 2.60

.11 50.00 8.17 6.53 5.45 4.67 4.08 3.63 3.27 2.97 2.72

.12 55.00 8.54 6.83 5.69 4.88 4.27 3.80 3.42 3.11 2.85

.12 60.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR80015

&XR

110015

.09 15.00 6.68 5.35 4.46 3.82 3.34 2.97 2.67 2.43 2.23

.11 20.00 8.17 6.53 5.45 4.67 4.08 3.63 3.27 2.97 2.72

.12 25.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

.13 30.00 9.65 7.72 6.44 5.52 4.83 4.29 3.86 3.51 3.22

.14 35.00 10.40 8.32 6.93 5.94 5.20 4.62 4.16 3.78 3.47

.15 40.00 11.14 8.91 7.43 6.36 5.57 4.95 4.46 4.05 3.71

.16 45.00 11.69 9.36 7.80 6.68 5.85 5.20 4.68 4.25 3.90

.17 50.00 12.25 9.80 8.17 7.00 6.13 5.45 4.90 4.46 4.08

.17 55.00 12.81 10.25 8.54 7.32 6.40 5.69 5.12 4.66 4.27

.18 60.00 13.37 10.69 8.91 7.64 6.68 5.94 5.35 4.86 4.46

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8002

&XR

11002

.12 15.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

.14 20.00 10.40 8.32 6.93 5.94 5.20 4.62 4.16 3.78 3.47

.16 25.00 11.51 9.21 7.67 6.58 5.75 5.12 4.60 4.19 3.84

.17 30.00 12.62 10.10 8.42 7.21 6.31 5.61 5.05 4.59 4.21

.19 35.00 13.74 10.99 9.16 7.85 6.87 6.11 5.49 5.00 4.58

.20 40.00 14.85 11.88 9.90 8.49 7.43 6.60 5.94 5.40 4.95

.21 45.00 15.78 12.62 10.52 9.02 7.89 7.01 6.31 5.74 5.26

.23 50.00 16.71 13.37 11.14 9.55 8.35 7.43 6.68 6.08 5.57

.24 55.00 17.63 14.11 11.76 10.08 8.82 7.84 7.05 6.41 5.88

.25 60.00 18.56 14.85 12.38 10.61 9.28 8.25 7.42 6.75 6.19

20

Calibration




Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8003

&XR

11003

.18 15.00 13.37 10.69 8.91 7.64 6.68 5.94 5.35 4.86 4.46

.21 20.00 15.59 12.47 10.40 8.91 7.80 6.93 6.24 5.67 5.20

.24 25.00 17.45 13.96 11.63 9.97 8.72 7.76 6.98 6.35 5.82

.26 30.00 19.31 15.44 12.87 11.03 9.65 8.58 7.72 7.02 6.44

.28 35.00 20.79 16.63 13.86 11.88 10.40 9.24 8.32 7.56 6.93

.30 40.00 22.28 17.82 14.85 12.73 11.14 9.90 8.91 8.10 7.43

.32 45.00 23.57 18.86 15.72 13.47 11.79 10.48 9.43 8.57 7.86

.34 50.00 24.87 19.90 16.58 14.21 12.44 11.06 9.95 9.05 8.29

.35 55.00 26.17 20.94 17.45 14.96 13.09 11.63 10.47 9.52 8.72

.37 60.00 27.47 21.98 18.32 15.70 13.74 12.21 10.99 9.99 9.16

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8004

&XR

11004

.24 15.00 17.82 14.26 11.88 10.18 8.91 7.92 7.13 6.48 5.94

.28 20.00 20.79 16.63 13.86 11.88 10.40 9.24 8.32 7.56 6.93

.32 25.00 23.39 18.71 15.59 13.37 11.69 10.40 9.36 8.51 7.80

.35 30.00 25.99 20.79 17.33 14.85 12.99 11.55 10.40 9.45 8.66

.38 35.00 27.84 22.28 18.56 15.91 13.92 12.38 11.14 10.13 9.28

.40 40.00 29.70 23.76 19.80 16.97 14.85 13.20 11.88 10.80 9.90

.42 45.00 31.37 25.10 20.91 17.93 15.69 13.94 12.55 11.41 10.46

.45 50.00 33.04 26.43 22.03 18.88 16.52 14.69 13.22 12.02 11.01

.47 55.00 34.71 27.77 23.14 19.84 17.36 15.43 13.88 12.62 11.57

.49 60.00 36.38 29.11 24.26 20.79 18.19 16.17 14.55 13.23 12.13

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8005

&XR

11005

.31 15.00 23.02 18.41 15.35 13.15 11.51 10.23 9.21 8.37 7.67

.35 20.00 25.99 20.79 17.33 14.85 12.99 11.55 10.40 9.45 8.66

.39 25.00 28.96 23.17 19.31 16.55 14.48 12.87 11.58 10.53 9.65

.43 30.00 31.93 25.54 21.29 18.24 15.96 14.19 12.77 11.61 10.64

.47 35.00 34.53 27.62 23.02 19.73 17.26 15.35 13.81 12.56 11.51

.50 40.00 37.13 29.70 24.75 21.21 18.56 16.50 14.85 13.50 12.38

.53 45.00 39.17 31.33 26.11 22.38 19.58 17.41 15.67 14.24 13.06

.56 50.00 41.21 32.97 27.47 23.55 20.60 18.32 16.48 14.99 13.74

.58 55.00 43.25 34.60 28.83 24.71 21.63 19.22 17.30 15.73 14.42

.61 60.00 45.29 36.23 30.20 25.88 22.65 20.13 18.12 16.47 15.10

21

Calibration




Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8006

&XR

11006

.37 15.00 27.47 21.98 18.32 15.70 13.74 12.21 10.99 9.99 9.16

.42 20.00 31.19 24.95 20.79 17.82 15.59 13.86 12.47 11.34 10.40

.47 25.00 34.90 27.92 23.27 19.94 17.45 15.51 13.96 12.69 11.63

.52 30.00 38.61 30.89 25.74 22.06 19.31 17.16 15.44 14.04 12.87

.56 35.00 41.58 33.26 27.72 26.76 20.79 18.48 16.63 15.12 13.86

.60 40.00 44.55 35.64 29.70 25.46 22.28 19.80 17.82 16.20 14.85

.64 45.00 47.15 37.72 31.43 26.94 23.57 20.96 18.86 17.15 15.72

.67 50.00 49.75 39.80 33.17 28.43 24.87 22.11 19.90 18.09 16.58

.71 55.00 52.35 41.88 34.90 29.91 26.17 23.27 20.94 19.04 17.45

.74 60.00 54.95 43.96 36.63 31.40 27.47 24.42 21.98 19.98 18.32

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8008

&XR

11008

.49 15.00 36.38 29.11 24.26 20.79 18.19 16.17 14.55 13.23 12.13

.57 20.00 42.32 33.86 28.22 24.18 21.16 18.81 16.93 15.39 14.11

.63 25.00 46.78 37.42 31.19 26.73 23.39 20.79 18.71 17.01 15.59

.69 30.00 51.23 40.99 34.16 29.28 25.62 22.77 20.49 18.63 17.08

.75 35.00 55.32 44.25 36.88 31.61 27.66 24.59 22.13 20.12 18.44

.80 40.00 59.40 47.52 39.60 33.94 29.70 26.40 23.76 21.60 19.80

.85 45.00 62.74 50.19 41.83 35.85 31.37 27.89 25.10 22.82 20.91

.89 50.00 66.08 52.87 44.06 37.76 33.04 29.37 26.43 24.03 22.03

.94 55.00 69.42 55.54 46.28 39.67 34.71 30.86 27.77 25.25 23.14

.98 60.00 72.77 58.21 48.51 41.58 36.38 32.34 29.11 26.46 24.26

22

Calibration




Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8001

&XR

11001

.06 15.00 2.97 2.38 1.98 1.70 1.49 1.32 1.19 1.08 0.99

.07 20.00 3.47 2.77 2.31 1.98 1.73 1.54 1.39 1.26 1.16

.08 25.00 3.96 3.17 2.64 2.26 1.98 1.76 1.58 1.44 1.32

.09 30.00 4.46 3.56 2.97 2.55 2.23 1.98 1.78 1.62 1.49

.10 35.00 4.70 3.76 3.14 2.69 2.35 2.09 1.88 1.71 1.57

.10 40.00 4.95 3.96 3.30 2.83 2.48 2.20 1.98 1.80 1.65

.11 45.00 5.20 4.16 3.47 2.97 2.60 2.31 2.08 1.89 1.73

.11 50.00 5.45 4.36 3.63 3.11 2.72 2.42 2.18 1.98 1.82

.12 55.00 5.69 4.55 3.80 3.25 2.85 2.53 2.28 2.07 1.90

.12 60.00 5.94 4.75 3.96 3.39 2.97 2.64 2.38 2.16 1.98

Nozzle Size

GPMPressure

PSI


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR80015

&XR

110015

.09 15.00 4.46 3.56 2.97 2.55 2.23 1.98 1.78 1.62 1.49

.11 20.00 5.45 4.36 3.63 3.11 2.72 2.42 2.18 1.98 1.82

.12 25.00 5.94 4.75 3.96 3.39 2.97 2.64 2.38 2.16 1.98

.13 30.00 6.44 5.15 4.29 3.68 3.22 2.86 2.57 2.34 2.15

.14 35.00 6.93 5.54 4.62 3.96 3.47 3.08 2.77 2.52 2.31

.15 40.00 7.43 5.94 4.95 4.24 3.71 3.30 2.97 2.70 2.48

.16 45.00 7.80 6.24 5.20 4.46 3.90 3.47 3.12 2.84 2.60

.17 50.00 8.17 6.53 5.45 4.67 4.08 3.63 3.27 2.97 2.72

.17 55.00 8.54 6.83 5.69 4.88 4.27 3.80 3.42 3.11 2.85

.18 60.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8002

&XR

11002

.12 15.00 5.94 4.75 3.96 3.39 2.97 2.64 2.38 2.16 1.98

.14 20.00 6.93 5.54 4.62 3.96 3.47 3.08 2.77 2.52 2.31

.16 25.00 7.67 6.14 5.12 4.38 3.84 3.41 3.07 2.79 2.56

.17 30.00 8.42 6.73 5.61 4.81 4.21 3.74 3.37 3.06 2.81

.19 35.00 9.16 7.33 6.11 5.23 4.58 4.07 3.66 3.33 3.05

.20 40.00 9.90 7.92 6.60 5.66 4.95 4.40 3.96 3.60 3.30

.21 45.00 10.52 8.42 7.01 6.01 5.26 4.68 4.21 3.83 3.51

.23 50.00 11.14 8.91 7.43 6.36 5.57 4.95 4.46 4.05 3.71

.24 55.00 11.76 9.41 7.84 6.72 5.88 5.23 4.70 4.28 3.92

.25 60.00 12.38 9.90 8.25 7.07 6.19 5.50 4.95 4.50 4.13

23

Calibration




Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8003

&XR

11003

.18 15.00 8.91 7.13 5.94 5.09 4.46 3.96 3.56 3.24 2.97

.21 20.00 10.40 8.32 6.93 5.94 5.20 4.62 4.16 3.78 3.47

.24 25.00 11.63 9.31 7.76 6.65 5.82 5.17 4.65 4.23 3.88

.26 30.00 12.87 10.30 8.58 7.35 6.44 5.72 5.15 4.68 4.29

..28 35.00 13.86 11.09 9.24 7.92 6.93 6.16 5.54 5.04 4.62

.30 40.00 14.85 11.88 9.90 8.49 7.43 6.60 5.94 5.40 4.92

.32 45.00 15.72 12.57 10.48 8.98 7.86 6.99 6.29 5.72 5.24

.34 50.00 16.58 13.27 11.06 9.48 8.29 7.37 6.63 6.03 5.53

.35 55.00 17.45 13.96 11.63 9.97 8.72 7.76 6.98 6.35 5.82

.37 60.00 18.32 14.65 12.21 10.47 9.16 8.14 7.33 6.66 6.11

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8004

&XR

11004

.24 15.00 11.88 9.50 7.92 6.79 5.94 5.28 4.75 4.32 3.96

.28 20.00 13.86 11.09 9.24 7.92 6.93 6.16 5.54 5.04 4.62

.32 25.00 15.59 12.47 10.40 8.91 7.80 6.93 6.24 5.67 5.20

.35 30.00 17.33 13.86 11.55 9.90 8.66 7.70 6.93 6.30 5.78

.38 35.00 18.56 14.85 12.38 10.61 9.28 8.25 7.43 6.75 6.19

.40 40.00 19.80 15.84 13.20 11.31 9.90 8.80 7.92 7.20 6.60

.42 45.00 20.91 16.73 13.94 11.95 10.46 9.30 8.37 7.61 6.97

.45 50.00 22.03 17.62 14.69 12.59 11.01 9.79 8.81 8.01 7.34

.47 55.00 23.14 18.51 15.43 13.22 11.57 10.29 9.26 8.42 7.71

.49 60.00 24.26 19.40 16.17 13.86 12.13 10.78 9.70 8.82 8.09

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8005

&XR

11005

.31 15.00 15.35 12.28 10.23 8.77 7.67 6.82 6.14 5.58 5.12

.35 20.00 17.33 13.86 11.55 9.90 8.66 7.70 6.93 6.30 5.78

.39 25.00 19.31 15.44 12.87 11.03 9.65 8.58 7.72 7.02 6.44

.43 30.00 21.29 17.03 14.19 12.16 10.64 9.46 8.51 7.74 7.10

.47 35.00 23.02 18.41 15.35 13.15 11.51 10.23 9.21 8.37 7.67

.50 40.00 24.75 19.80 16.50 14.14 12.38 11.00 9.90 9.00 8.25

.53 45.00 26.11 20.89 17.41 14.92 13.06 11.61 10.44 9.50 8.70

.56 50.00 27.47 21.98 18.32 15.70 13.74 12.21 10.99 9.99 9.16

.58 55.00 28.83 23.07 19.22 16.48 14.42 12.82 11.53 10.49 9.61

.61 60.00 30.20 24.16 20.13 17.25 15.10 13.42 12.08 10.98 10.07

24

Calibration




Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8006

&XR

11006

.37 15.00 18.32 14.65 12.21 10.47 9.16 8.14 7.33 6.66 6.11

.42 20.00 20.79 16.63 13.86 11.88 10.40 9.24 8.32 7.56 6.93

.47 25.00 23.27 18.61 15.51 13.29 11.63 10.34 9.31 8.46 7.76

.52 30.00 25.74 20.59 17.16 14.71 12.87 11.44 10.30 9.36 8.58

.56 35.00 27.72 22.18 18.48 15.84 13.86 12.32 11.09 10.08 9.24

.60 40.00 29.70 23.76 19.80 16.97 14.85 13.20 11.88 10.80 9.90

.64 45.00 31.43 25.15 20.96 17.96 15.72 13.97 12.57 11.43 10.48

.67 50.00 33.17 26.53 22.11 18.95 16.58 14.74 13.27 12.06 11.06

.71 55.00 34.90 27.92 23.27 19.94 17.45 15.51 13.96 12.69 11.63

.74 60.00 36.63 29.30 24.42 20.93 18.32 16.28 14.65 13.32 12.21

Nozzle Size

GPMPressure


4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00

XR8008

&XR

11008

.49 15.00 24.26 19.40 16.17 13.86 12.13 10.78 9.70 8.82 8.09

.57 20.00 28.22 22.57 18.81 16.12 14.11 12.54 11.29 10.26 9.41

.63 25.00 31.19 24.95 20.79 17.82 15.59 13.86 12.47 11.34 10.40

.69 30.00 34.16 27.32 22.77 19.52 17.08 15.18 13.66 12.42 11.39

.75 35.00 36.88 29.50 24.59 21.07 18.44 16.39 14.75 13.41 12.29

.80 40.00 39.60 31.68 26.40 22.63 19.80 17.60 15.84 14.40 13.20

.85 45.00 41.83 33.46 27.89 23.90 20.91 18.59 16.73 15.21 13.94

.89 50.00 44.06 35.24 29.37 25.17 22.03 19.58 17.62 16.02 14.69

.94 55.00 46.28 37.03 30.86 26.45 23.14 20.57 18.51 16.83 15.43

.98 60.00 48.51 38.81 32.34 27.72 24.26 21.56 19.40 17.64 16.17

25

Planter/Incorporation Kits



Great Plains Models AS-4, AS-6, & AS-8Mounting Instructions for Incorporation Equipment

• T-4 for 10’ to 15’ Widths• T-6 for 16’ to 23’ Widths• T-8 for 24’ to 32’ Widths

Step 1 Using 7” carriage bolts attach adjustable arm brack-ets on disc frame spaced and positioned according to the Great Plains Chart, page 28.Step 2 Insert 15” extension arm into adjustable arm brack-ets; set to clear disc frame, and tighten with square head set screw.Step 3 Insert adjustable swivel into 15” extension arm, and tighten with square head set screw.Step 4 Place special drop pipe through adjustable swivel collar and screw poly blind tee on to the end of special drop pipe.Step 5 Screw hose barb elbow in the back of the poly blind tee. Attach Great Plains MeterCone™ nozzle into front of ply blind tee, angling nozzle away from implement.Step 6 Mount manifold bracket on hydraulic cylinder or any other feasible place using 24” steel clamp, and attach me-

tered manifold.Step 7 Attach hose to hose barb on blind tee and tighten clamp.Step 8 Insert Great Plains recalibratable pressure gauge into top of manifold.Step 9 Make final check of broadcast coverage under field conditions. It may be necessary to make minor adjustments to assure accurate application.

Final Field Adjustment of NozzlesThe drawing below shows a top view of the large oval Great Plains MeterCone™ patterns.

The patterns should meet and overlap two inches, also the patterns should not be allowed to strike the braces or any other object before coming in contact with the soil.

a) The disc is cutting 4” deep and the nozzle height of 16” is measured from the ground under field conditions. Nozzle height is determined from Application Guide.

b) The MeterCone™ nozzle is angled forward to obtain better angular coverage. The desired angle is approximate-ly ten degrees forward perpendicular to the ground.


Typical assembly of kit mounted on tillage equipment.

26




NOTE: If LOWER gallonages are desired, use MC-1.25 or MC-1.875. When using MC-1.25, divide above charts by 2.00; When using MC-1.875, divide above charts by 1.33.

NOTE: If HIGHER gallonages are desired, use MC-5, MC-7.5, MC-10, MC-12.5 or MC-15 Nozzles.MC-5, multiply by 2.0; MC-7.5, multiply by 3.00; MC-10, multiply by 4.00; MC-12.5 multiply by 5.00; MC-15, multiply by 6.00.

Incorporation Charts (Gallons Per Acre @ Miles Per Hour)

Nozzle Spacing

PressureP.S.I. G.P.M.

Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

26”Spacing

9”Height

10.0 .25 14.28 12.69 11.42 10.38 9.52 8.79 8.16 7.62 7.14

15.0 .31 17.71 15.74 14.16 12.88 11.80 10.90 10.12 9.44 8.85

20.0 .35 19.99 17.77 15.99 14.54 13.33 12.30 11.42 10.66 10.00

25.0 .40 22.85 20.31 18.28 16.62 15.23 14.06 13.05 12.18 11.42

30.0 .43 24.56 21.83 19.65 17.86 16.37 15.11 14.03 13.10 12.28

35.0 .46 26.27 23.35 21.02 19.11 17.52 16.17 15.01 14.01 13.14

40.0 .50 28.56 25.38 22.85 20.77 19.04 17.57 16.32 15.23 14.28

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

28”Spacing

10”Height

10.0 .25 13.26 11.79 10.61 9.64 8.84 8.16 7.58 7.07 6.63

15.0 .31 16.44 14.61 13.15 11.96 10.96 10.12 9.39 8.77 8.22

20.0 .35 18.56 16.50 14.85 13.50 12.38 11.42 10.61 9.90 9.28

25.0 .40 21.21 18.86 16.97 15.43 14.14 13.05 12.12 11.31 10.61

30.0 .43 22.81 20.27 18.24 16.59 15.20 14.03 13.03 12.16 11.40

35.0 .46 24.40 21.69 19.52 17.74 16.26 15.01 13.94 13.01 12.20

40.0 .50 26.52 23.57 21.21 19.29 17.68 16.32 15.15 14.14 13.26

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

30”Spacing101⁄2”Height

10.0 .25 12.38 11.00 9.90 9.00 8.25 7.62 7.07 6.60 6.19

15.0 .31 15.35 13.64 12.28 11.16 10.23 9.44 8.77 8.18 7.67

20.0 .35 17.33 15.40 13.86 12.60 11.55 10.66 9.90 9.24 8.66

25.0 .40 19.80 17.60 15.84 14.40 13.20 12.18 11.31 10.56 9.90

30.0 .43 21.29 18.92 17.03 15.48 14.19 13.10 12.16 11.35 10.64

35.0 .46 22.77 20.24 18.22 16.56 15.18 14.01 13.01 12.14 11.39

40.0 .50 24.75 22.00 19.80 18.00 16.50 15.23 14.14 13.20 12.38

27







Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@


10.0 .25 11.60 10.31 9.28 8.44 7.73 7.14 6.63 6.19 5.80

15.0 .31 14.39 12.79 11.51 10.46 9.59 8.85 8.22 7.67 7.19

20.0 .35 16.24 14.44 12.99 11.81 10.83 10.00 9.28 8.66 8.12

25.0 .40 18.56 16.50 14.85 13.50 12.38 11.42 10.61 9.90 9.28

30.0 .43 19.95 17.74 15.96 14.51 13.30 12.28 11.40 10.64 9.98

35.0 .46 21.35 18.98 17.08 15.53 14.23 13.14 12.20 11.39 10.67

40.0 .50 23.20 20.63 18.56 16.88 15.47 14.28 13.26 12.38 11.60

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

34”Spacing

12”Height

10.0 .25 10.92 9.71 8.74 7.94 7.28 6.72 6.24 5.82 5.46

15.0 .31 13.54 12.04 10.83 9.85 9.03 8.33 7.74 7.22 6.77

20.0 .35 15.29 13.59 12.23 11.12 10.19 9.41 8.74 8.15 7.64

25.0 .40 17.47 15.53 13.98 12.71 11.65 10.75 9.98 9.32 8.74

30.0 .43 18.78 16.69 15.02 13.66 12.52 11.56 10.73 10.02 9.39

35.0 .46 20.09 17.86 16.07 14.61 13.39 12.36 11.48 10.72 10.05

40.0 .50 21.84 19.41 17.47 15.88 14.56 13.44 12.48 11.65 10.92

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

36”Spacing

13”Height

10.0 .25 10.31 9.17 8.25 7.50 6.88 6.35 5.89 5.50 5.16

15.0 .31 12.79 11.37 10.23 9.30 8.53 7.87 7.31 6.82 6.39

20.0 .35 14.44 12.83 11.55 10.50 9.63 8.88 8.25 7.70 7.22

25.0 .40 16.50 14.67 13.20 12.00 11.00 10.15 9.43 8.80 8.25

30.0 .43 17.74 15.77 14.19 12.90 11.83 10.92 10.14 9.46 8.87

35.0 .46 18.98 16.87 15.18 13.80 12.65 11.68 10.84 10.12 9.49

40.0 .50 20.63 18.33 16.50 15.00 13.75 12.69 11.79 11.00 10.31

28







Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

38”Spacing

14”Height

10.0 .25 9.77 8.68 7.82 7.11 6.51 6.01 5.58 5.21 4.88

15.0 .31 12.11 10.77 9.69 8.81 8.08 7.46 6.92 6.46 6.06

20.0 .35 13.68 12.16 10.94 9.95 9.12 8.42 7.82 7.29 6.84

25.0 .40 15.63 13.89 12.51 11.37 10.42 9.62 8.93 8.34 7.82

30.0 .43 16.80 14.94 13.44 12.22 11.20 10.34 9.60 8.96 8.40

35.0 .46 17.98 15.98 14.38 13.07 11.98 11.06 10.27 9.59 8.99

40.0 .50 19.54 17.37 15.63 14.21 13.03 12.02 11.17 10.42 9.77

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@


10.0 .25 9.28 8.25 7.43 6.75 6.19 5.71 5.30 4.95 4.64

15.0 .31 11.51 10.23 9.21 8.37 7.67 7.08 6.58 6.14 5.75

20.0 .35 12.99 11.55 10.40 9.45 8.66 8.00 7.43 6.93 6.50

25.0 .40 14.85 13.20 11.88 10.80 9.90 9.14 8.49 7.92 7.43

30.0 .43 15.96 14.19 12.77 11.61 10.64 9.82 9.12 8.51 7.98

35.0 .46 17.08 15.18 13.66 12.42 11.39 10.51 9.76 9.11 8.54

40.0 .50 18.56 16.50 14.85 13.50 12.38 11.42 10.61 9.90 9.28

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

42”Spacing

15”Height

10.0 .25 8.84 7.86 7.07 6.43 5.89 5.44 5.05 4.71 4.42

15.0 .31 10.96 9.74 8.77 7.97 7.31 6.75 6.26 5.85 5.48

20.0 .35 12.38 11.00 9.90 9.00 8.25 7.62 7.07 6.60 6.19

25.0 .40 14.14 12.57 11.31 10.29 9.43 8.70 8.08 7.54 7.07

30.0 .43 15.20 13.51 12.16 11.06 10.14 9.36 8.69 8.11 7.60

35.0 .46 16.26 14.46 13.01 11.83 10.84 10.01 9.29 8.67 8.13

40.0 .50 17.68 15.71 14.14 12.86 11.79 10.88 10.10 9.43 8.84

29







Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@


10.0 .25 8.44 7.50 6.75 6.14 5.63 5.19 4.82 4.50 4.22

15.0 .31 10.46 9.30 8.37 7.61 6.98 6.44 5.98 5.58 5.23

20.0 .35 11.81 10.50 9.45 8.59 7.88 7.27 6.75 6.30 5.91

25.0 .40 13.50 12.00 10.80 9.82 9.00 8.31 7.71 7.20 6.75

30.0 .43 14.51 12.90 11.61 10.55 9.68 8.93 8.29 7.74 7.26

35.0 .46 15.53 13.80 12.42 11.29 10.35 9.55 8.87 8.28 7.76

40.0 .50 16.88 15.00 13.50 12.27 11.25 10.38 9.64 9.00 8.44

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5@

46”Spacing

16”Height

10.0 .25 8.07 7.17 6.46 5.87 5.38 4.97 4.61 4.30 4.04

15.0 .31 10.01 8.90 8.01 7.28 6.67 6.16 5.72 5.34 5.00

20.0 .35 11.30 10.04 9.04 8.22 7.53 6.95 6.46 6.03 5.65

25.0 .40 12.91 11.48 10.33 9.39 8.61 7.95 7.38 6.89 6.46

30.0 .43 13.88 12.34 11.11 10.10 9.25 8.54 7.93 7.40 6.94

35.0 .46 14.85 13.20 11.88 10.80 9.90 9.14 8.49 7.92 7.43

40.0 .50 16.14 14.35 12.91 11.74 10.76 9.93 9.22 8.61 8.07

Custom Incorporation Chart Use Formula on Page 5 to fill in chart

Nozzle Spacing


Miles Per Hour

4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0

MeterCone®

2.5

@

___”Spacing

10.0 .25

15.0 .31

20.0 .35

25.0 .40

30.0 .43

35.0 .46

40.0 .50

30




Broadcasting Behind A Planter or Drill1. The MeterCone™ nozzle pattern should overlap ap-

proximately 2”.

G.P.M. = gallons per minute

2. Suggested pressures (10-40 PSI). Consult Herbicide Label.

3. Angle MeterCone™ nozzle ten degrees to rear to get maximum coverage.

Planter Row

Width

Appli-cation

System Nozzle

Number

GPM (*)

Pres-sure P.S.I.

Gallons Per Acre Based on Various M.P.H. Noz. Hgt. From Top

of Ground (Inches)

4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8

30” MC-2.5

32384448505564

10* 15 20 23* 25 30 40*

12.415.117.418.619.721.324.8

11.013.415.416.517.418.922.0

9.912.113.914.715.617.019.8

9.011.012.613.514.315.518.0

8.310.111.512.413.014.116.5

7.69.3

10.711.412.113.115.0

7.18.69.9

10.611.112.114.1

6.68.19.29.9

10.411.313.2

6.27.58.79.39.8

10.712.4

11

36” MC-2.5

32384448505564

10* 15 20 23* 25 30 40*

10.312.614.515.516.517.820.7

9.211.212.813.814.515.818.3

8.310.111.612.313.014.216.5

7.59.2

10.511.311.912.915.0

6.98.49.6

10.410.811.813.7

6.47.78.99.6

10.111.012.5

5.97.28.28.99.3

10.111.8

5.56.77.78.38.79.5

11.0

5.26.37.27.88.28.9

10.3

13

38” MC-2.5

32384448505564

10* 15 20 23* 25 30 40*

9.811.913.714.715.616.819.6

8.710.612.213.013.714.917.4

7.89.5

10.911.612.313.515.6

7.18.79.9

10.711.312.214.2

6.58.09.19.8

10.311.213.0

6.07.38.49.09.5

10.411.8

5.66.87.88.48.89.6

11.2

5.26.47.37.88.29.0

10.4

4.96.06.97.47.78.49.8

131⁄2

40” MC-2.5

32384448505564

10* 15 20 23* 25 30 40

9.311.413.114.014.816.018.6

8.310.111.612.413.114.216.5

7.59.1

10.411.111.712.814.9

6.88.39.5

10.210.711.613.5

6.27.68.79.39.8

10.612.4

5.77.08.08.69.19.9

11.3

5.36.57.48.08.49.1

10.6

5.06.16.97.57.88.59.9

4.75.76.57.07.48.08.3

14

31




MC-2.5 70˚SS Application System MeterCone™ Nozzle available to raise nozzle higher for same band width. *O.P.M. = ounces per minute

Banding Behind A Planter

Note: Chart flows based on Planted Acres1. To set width of band with the MeterCone™ nozzle ap-

proximately 1” nozzle height = 3” band. Example 4” height = 12” band.

2. Suggested pressures (10-40 PSI). Consult Herbi-cide Label.

3. Angle MeterCone™ nozzle approximately 0-5 de-grees to rear so spray pattern will not hit press wheel.

Planter Row

Width

ASNozzle

Number

Manifold

P.S.I.

O.P.M.

Noz. Hgt. From Top of

Ground (in.)

Nozzle Spacing

(in.)

Band Width (in.)

Gallons Per Acre Based on Various M.P.H.

4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8

30” MC-2.51010

3232

45

3030

1215

12.4 11.0 9.9 9.0 8.3 7.6 7.1 6.6 6.2

30” MC-2.51515

3838

45

3030

1215

15.1 13.4 12.1 11.0 10.1 9.3 8.6 8.1 7.5

30” MC-2.51010

3232

45

3636

1215

10.3 9.2 8.3 7.5 6.9 6.4 5.9 5.5 5.2

36” MC-2.51515

3838

45

3636

1215

12.6 11.2 10.1 9.2 8.4 7.7 7.2 6.7 6.3

38” MC-2.51010

3232

45

3838

1215

9.8 8.7 7.8 7.1 6.5 6.0 5.6 5.2 4.9

38” MC-2.51515

3838

45

3838

1215

11.9 10.6 9.5 8.7 8.0 7.3 6.8 6.4 6.0

40” MC-2.51010

3232

45

4040

1215

9.3 8.3 7.5 6.8 6.2 5.7 5.3 5.0 4.7

40” MC-2.51515

3838

45

4040

1215

11.4 10.1 9.1 8.3 7.6 7.0 6.5 6.1 5.7

32

Parts



Part No. Description Part No. Description

830-071C 1/4 MPT x 3/8 HB Poly 990-117T 3/8 X 250’ EVA Heavy Tubing

800-169C 3/8 Wire Hose Clamp 506-226D 3/8 x 50’ EVA Heavy Tubing

509-130D 3/8 x 108” EVA Heavy Tubing 509-105H Adjustable Swivel

509-132D 3/8 x 228” EVA Heavy Tubing 509-104H Extension Arm

506-225D 3/8 x 100’ EVA Heavy Tubing 509-106H Adjustable Arm Bracket w/ Collar

830-218C Blind Tee 801-022C 3/8x 1/2” Set Screw

509-107H Drop Pipe Assembly 506-534H 8 Port Manifold

509-105D Adjustable Arm Bracket 507-032S 100 PSI Liquid Filled Gauge

802-460C 1/4 x 7” All Thread Bolt w/ Stainless Steel Protector

803-194C 1/4 Flange Whiz Nut 829-007C (3 1/2” 100 PSI Liquid Filled Gauge–only)

830-111C 1/4 MPT x3/8 90˚ HB Poly 830-192C 1/4 MPT Close x 7/8” S.S.

509-129D 3/8 x 58” EVA Heavy Tubing

509-131D 3/8 x 168” EVA Heavy Tubing

507-032S 830-192C

506-034H

830-218C 800-169C

830-071C 830-111C509-107H

509-106H803-194C

802-460C

509-105H

801-022C

506-226D3/8” x 50’506-225D3/8” x 100’900-117T3/8” x 250’

509-104H

509-105D

Parts

Great Plains Manufacturing, Inc.Corporate Office: PO. Box 5060

Salina, Kansas 67402-5060 USA

Date post:	15-Apr-2018
Category:	Documents
Upload:	vanngoc
View:	213 times
Download:	0 times

Application Guide - Great Plains Manufacturing · 2/7/06 Application Guide 509-200M Great Plains...

Documents