FX SYSTE M S
ApplicationThe mixer is used for mixing of powders and liquids, for recombined dairy products, sugar solutions, brine, etc.
CAPACITY
12,000 to 50,000 l/hour of recombined product
OPE RATION
In principle the mixer is an integrated injector/centrifugal pump.
It consists of a mixer/pump housing onto which an injector pipe is
built coaxially into the pump inlet. In the double inlet pipe the liquid
is added in the outer pipe section and the powder in the centre.
In connection with the injector pipe, a powder hopper is mounted
above the mixer.
Between funnel and mixer a throttle valve regulates the powder
quantity.
During operation the liquid is accelerated by means of the mixing
wheel which creates a vacuum centrally in the injector pipe by
which the powder is sucked in. The products are mixed in the
mixer housing. In addition to the pump pressure the mixing wheel
also generates turbulence and high shear forces in the mixture
ensuring effective and homogeneous mixing.
For high product viscosities (>500cp) a booster pump may be
needed to feed the mixer.
STAN DAR D S PECI F ICATION• Two models: TPM+1 with motor coupled directly to the mixer
shaft and TPM+2 with V-drive between motor and mixer.
• All parts in contact with the product are made of acid proof stainless steel AISI 316L / DIN1.4404.
• The Powder hopper is made of stainless steel AISI 304 / 1.4301 and is available in 30, 45, and 100 litres (TPM+2 only 100 litres).
• With level sensor and/or vibrator on powder hopper if required.
• Manual or air operated throttle valve for powder regulation/shut off.
• Double shaft seal with water flushing (W+ pump seal).
• Seal material in EPDM or FPM (Viton), FDA quality.
• Motor is totally enclosed in IEC or NEMA norm, covered by stainless steel shroud.
• Sanitary design for CIP cleaning.
• Inlet/outlet fittings in accordance with required standard: ISO, DIN, etc.
APV Flex-Mix™ TPM+
POWD E R M IXE R
215
650100
780
371
142
Ø800
500
1255
644
33
98
388
3"
2½"
VERSIONGENDCLGEN-KO1GENDIMSTILGENINCHGENEDITORGENSCALEGENSTDLGGENPARDRUGENPARSUMGENPARPOSGENPOSINCGENPOSBLKGENPOSVARGENIFGEN-KO3GEN-KO2
GEN-KO2GEN-KO3GENIFGENPOSVARGENPOSBLKGENPOSINCGENPARPOSGENPARSUMGENPARDRUGENSTDLGGENSCALEGENEDITORGENINCHGENDIMSTILGEN-KO1GENDCLVERSIONGEN-KO2GEN-KO3GENIFGENPOSVARGENPOSBLKGENPOSINCGENPARPOSGENPARSUMGENPARDRUGENSTDLGGENSCALEGENEDITORGENINCHGENDIMSTILGEN-KO1GENDCLVERSION
Ø404
200
61368
3
1409 (100L)
1189 (30L)1251 (45L)
577
Ø38
97.5
Ø38
628 (100L)470 (45L)408.5 (30L)
Ø540 (30L)Ø610 (45L)Ø794 (100L)
For more information about our worldwide locations, approvals, certifications, and local representatives, please visit www.spx.com.
SPX Corporation reserves the right to incorporate our latest design and material changes without notice or obligation. Design features, materials of construction and dimen-
sional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing.
ISSUED 09/2012 3020-04-09-2012-GB COPYRIGHT © 2009 SPX Corporation
SPX Flow Technology, Pasteursvej, DK-8600 Silkeborg
P: (+45) 70 278 278 F: (+45) 70 278 330
TPM+1 TPM+2
M OTO R KW 4 – 5 .5 – 7.5 11 – 15
R P M @ 50H Z 2900 2200
L I Q U I D CAPAC ITY L/ H MAX. 25,000 MAX. 50,000
P OWD E R CAPAC ITY ( * ) KG / M I N. 60 150
MAX. TE M P E RATU R E C° 140 140
I N LET P R E S S U R E (F E E D P R E S S U R E) M I N. BAR 0.5 0.5
O UTLET P R E S S U R E (C O U NTE R P R E S S U R E) MAX. BAR 1.5 1.5
SYSTE M P R E S S U R E, MAX. BAR 10 10
S E RVI C E WATE R FO R S HAFT S EAL
CAPAC ITY L/ H 15-30 15-30
P R E S S U R E, MAX. BAR 7 7
W E I G HT KG
75 (4 KW) 160 (11KW)
90 (5 .5KW) 175 (15KW)
100 (7.5KW)
TECH N ICAL DATA
TPM+2TPM +1
D I M E N S IONAL S KETCH E S
( * ) TH E CAPAC ITY D E P E N D S O N TH E P OWD E R TYP E. C O NTACT S PX FO R R E C O M M E N DATI O N S.