ACCESSORIES

44

ACCESSO

RIES

ACCESSORIESMetal mailboxes can be delivered by single units or banked (except model FUTURE V1000).Whenever delivered as single units, the price is marked near the mailbox.Whenever delivered as bank of mailboxes, there will be an extra charge indicated in the JOINED MAILBOXES section, except the cases where metallic SURROUNDS or FRAMES accessories are selected.Wooden mailboxes are always supplied in banks of mailboxes with no extra charge. There is also option of individual mail-boxes upon request.Below, we present several available accessories for banked mailboxes.

COLOUR OPTIONS

TABLE

FRAMES

PARCEL SHELVES

Customize the finish of your mailbox. You will find a full range of Arregui RAL colours.

An elegant and useful accessory as support for mailboxes groups. Practical and decorative, fills any environment with style.

When the bank is built in the wall, this is the best accessory to leave the bank flush with the wall.

Made up in the bank of mailboxes, they allow to leave flyers on them.

ENGRAVING MAILBOXES AND NAME PLATES

ROOF

SURROUNDS

NOTICE BOARDS

BANK NAME PLATE

SUPPORTS

SHELTER

INTERCOM SYSTEM BOX

Customize your mailbox numbering and lette-ring mailbox flaps or doors with laser engraving. Name cards can be customized by engraving the desired text; usually the owner’s name.

When the mailboxes are installed outside, ex-posed to inclement weather, the roof protects the mailboxes.

If the bank of mailboxes is not built in the wall a surronding around the bank gives a better appearance to the sides and top of the mailbo-xes. If the rear is visible, a piece can be added to cover it.

Made up in the bank of mailboxes, this notice board is a very practical way of advertising or noticing.

Name plates can be incorporated to the bank of mailboxes to identify the block of houses.

Base suports, side supports, wall-fixed su-pports… of different materials and with mat-ching finishes to suit the mailboxes.

When the mailboxes are installed outside, expo-sed to inclement weather, the shelter protects the mailboxes as well as the individuals when picking the mail.

Made up in the bank of mailboxes, this box is prepared to install the Intercom system.

45

ACC

ESSO

RIES

ACCESSORIES

COLOURS

JOINED MAILBOXES

CHARACTERISTICSAll the range of ARREGUI’s metal mailboxes may be powder coated in any finish of customer’s choice, from our colour chart shown in this page.

Due to the limitations of the printing process, colour match must be checked against the official RAL Colour Chart. This is only intended to be a reference guide.

The Arregui’s colours range possesses a smooth and bright finish on the product, except for those colours otherwise indicated.

LACQUERED FINISHES

Sky blue: RAL 5015

English red:RAL 3009

Violet blue:RAL 5000

Granite grey:RAL 7016

Red: RAL 3020

White: RAL 9016

Matt black: RAL 9005M

Shine black:RAL 9005B

Volcanic sand: RAL 7011T

Orange: RAL 2004

Acid green: RAL 6018

Forest green: RAL 6005

Atlantic sand: GRIS 2500 Sablé

Textured black: RAL 9005T

Textured silver: RAL 9006T

TEXTURED LACQUERED FINISHES

Also, any RAL finish from the Official RAL Colour Chart is available upon re-quest.

EXTRAS

Nacre: RX 7190-XW

Bond silver: RAL 9006BD

PREMIUM LACQUERED FINISHES

Aluminium Stainless steel

ANTI-FINGERPRINTS

ANTI-FINGERPRINTS

ANTI-FINGERPRINTS

Metallic Mailboxes can be joined in a bank with an additional charge, except the cases where metallic surrounds or frames accessories are selected.

46

ACCESSO

RIES

ACCESSORIES

LASER ENGRAVING

NAME CARDS ENGRAVING

ENGRAVING

Mailboxes doors and flaps can be laser engraved num-bering or lettering the mailbox in order to indetify them.

It is available for all the metal mailboxes finishes: lac-quered, anodized and stainless steel. It is NOT availale for wood veneer or plastic doors.

Tipografy: Arial

Optional customization with company logos, icons, etc.

Ref. LASER 1: Engraving up to 4 charactersRef. LASER 2: Engraving from 5 to 10 characters

Name cards in the mailboxes can be customized by en-graving the desired text; usually the owner’s name.

2 types:

• Adhesive card to replace the name card holder.• Ordinary card to place inside the name card holder.

Available finishes:

• Black background and White letters.• Silver background and black letters.• Gold background and black letters.

Engraving of 3 to 5 lines is possible.

Engraving is done in capital letters and the text align-ment is centered.

The text to be engraved shall be typewritten.

The cards are not supplied fixed in the mailboxes.

CHARACTERISTICSName plates can be integrated into the bank of mailbo-xes to identify the bank with the name of the block of appartments, road, street... and it is placed on the top of the bank of mailboxes.

In order to fix this aluminium name plate, it is strictly re-commended to use a surround on the bank of mailboxes. (see page 50 and 51).

Plate dimensions: 135 mm high. Maximum length: 2000 mm. The length of the plate is the same as the length of the bank of mailboxes.

Front size: 75 mm high.

Colour to select in page 45

NAME PLATES FOR BANKS OF MAILBOXES

Without name card holder With name card holder

C-560 Steel or aluminium name plate colour to select

C-562 Silver anodized aluminium name plate

C-555 Satin finished stainless steel name plate

C-557 Gloss finished stainless steel name plate

47

ACC

ESSO

RIES

ACCESSORIES

IN BANK OF METALLIC MAILBOXES

IN BANK OF WOODEN MAILBOXES

PARCEL SHELFS

Parcel shelves are very useful to leave advertising, flyers…

Metal parcel shelves take up 1, 2 or 3 mailboxes wide and help to assemble regular shaped banks of mailbo-xes.

Available for the following metallic Mailboxes:MILENIO / HABITAT / NEO / FUTURE HORIZONTAL / LIBERTY / INFINITY / MIRA HORIZONTAL

Within wooden horizontal bank of mailboxes, parcel shelfs without size restriction can be made.

Available for the following wooden Mailboxes:ELEGANTE / NATURA / PERSONAL

Width 1 Width 2 Width 3

Width 1 Width 2 Width 3

Milenio H4400/Infinity H2000

H-44B1 H-44B2 H-44B3

Milenio H4500/Infinity H2100

H-45B1 H-45B2 H-45B3

Milenio H4600/Infinity H2200

H-46B1 H-46B2 H-46B3

Habitat H8100 H-81B1 H-81B2 H-81B3

Habitat H8200 H-82B1 H-82B2 H-82B3

Habitat H8100 INOX

H-81B1 I H-81B2 I H-81B3 I

Habitat H8200 INOX

H-82B1 I H-82B2 I H-82B3 I

Future H3400/Liberty H3430/Mira H8700

H-34B1 H-34B2 H-34B3

Future H3500/Neo H8500/Liberty H3530/Mira H8800

H-35B1 H-35B2 H-35B3

Future H3600/Liberty H3630/Mira H8900

H-36B1 H-36B2 H-36B3

Neo H8600 H-86B1 H-86B2 H-86B3

48

ACCESSO

RIES

ACCESSORIES

IN BANK OF METALLIC MAILBOXES

IN BANK OF WOODEN MAILBOXES

CHARACTERISTICS

NOTICE BOARDS

INTERCOM SYSTEM BOX

Banks of metal and timber mailboxes may include notice boards.

Notice boards take up 3 or 6 mailboxes wide (3 rows x 1 column or 3 rows x 2 columns).

In order to fix the notice board, mailboxes must be banked with a surround.

Metal notice boards consist of an aluminium structure, with methacrylate door and lock.

Available for the following metallic Mailboxes: MILENIO, FUTURE, INFINITY y MIRA.

Within wooden horizontal bank of mailboxes, notice boards without size restriction can be made.

Suitable for all the range of wooden mailboxes except KUBE.

Made up in the bank of mailboxes, this box is prepared to install the Intercom system.

Intercom system is fixed on the panel provided (techni-cal advise is required).

It is suitable for models MILENIO H4500 / MILE-NIO H4550 (double access range) / HABITAT 8100/H8200, HABITAT H8150/H8250 (double access range), TECNUM H4300/H4350 and INFINITY H2100.

Material: aluminium panel for MILENIO mailboxes (with silver anodised or white lacquered finish) and stainless steel or steel colour to select panel for HABITAT and INFINITY mailboxes.

This Intercom system box can include all the internal mechanisms and wires to install the Intercom. The box is sealed with a nylon brush in order to protect the me-chanisms from the bad weather.

There are two different sizes for the Intercom system box, of 2 and 3 mailboxes high.

3 mailboxes 6 mailboxes

Future H3400/H3600Mira H8700/H8900

H-34P3 H-34P6

Future H3500Neo H8500/Mira H8800

H-35P3 H-35P6

Milenio H4400/H4600Infinity H2000/H2200

H-44P3 H-44P6

Milenio H4500Infinity H2100

H-45P3 H-45P62 mailboxes 3 mailboxes

Milenio H4500/H4550Infinity H2100

H-45AU2 H-45AU3

Habitat H8100/H8150 H-81AU2 H-81AU3

Habitat H8200/H8250 H-82AU2 H-82AU3

Tecnum H4300/H4350 H-43AU2 H-43AU3

49

ACC

ESSO

RIES

ACCESSORIES

STAINLESS STEELWOOD VENEER

When the bank is built in the wall, this is the best accessory to leave the bank flush with the wall.

Frames are supplied fixed to the bank of mailboxes.

The edges are cut at 45º angles.

Thickness: 1mm - Width: 40mm

Maximum length: 2.000mm

Thickness: 15mm - Width: 50mm

Maximum length: 2350mm

They are supplied by custom cut strips, NOT fixed to the bank of mailboxes. The edges are NOT cut at 45° angles.

ALUMINIUM

FRAMES

Frames are cut at 45° angles.

Thickness: 1.20mm - Width: 40mm

Maximum length: 2.080mm except silver anodized fra-mes (3000 mm).

Colour to select in page 45.

Beech veneer C-411Sapelly veneer C-412Oak veneer C-415

Ref. Finish

Lacquered (colour to select) C-470Silver anodized C-472

Ref. Finish

Gloss C-427Satin finished C-425

Ref. Finish

50

ACCESSO

RIES

ACCESSORIES

GALVANISED STEEL WITH VOLUMEGALVANIZED STEEL

SURROUNDS

Thickness: 21mm

Maximum length: 2.080mm

Galvanized steel back side.

Colour to select in page 45.

Option 1. Thickness: 1.2mm. Suitable for bank of hori-zontal Mailboxes.

Option 2. Thickness: 2mm. Recommended for verti-cal mailboxes and those banks of horizontal mailboxes which exceed a width of 1.500 mm, for it balances pos-sible corrugations of the wall or mailboxes.

Maximum length: 2.080mm.

Galvanized steel back side.

Colour to select in page 45.

4 pieces 4 pieces + back

If the bank of mailboxes is not built in the wall a surronding around the bank gives a better appea-rance to the sides and top of the mailboxes. If the rear is visible, a piece can be added to cover it.

Arregui recommends placing the bank of mailboxes undercover and protected from the rain.

Surrounds are suplied fixed to the bank of mailboxes.

Thickness 1,2mm

Thickness 2mm

Colour to select C-490 (4 pieces)

Colour to select C-440 (4 pieces + back)

Colour to select C-100 (4 pieces)

Colour to select C-110 (4 pieces + back)

Colour to select C2-490 (4 pieces)

Colour to select C2-440 (4 pieces + back)

Ref. Ref.

Ref.

Finish Finish

Finish

51

ACC

ESSO

RIES

ACCESSORIES

STAINLESS STEEL WITH VOLUMESTAINLESS STEEL

WOOD VENEER

SURROUNDS

Thickness: 21mm - Maximum length: 2.080mm

Stainless steel back side.

Very suitable for exterior application.

Thickness: 1.20mm - Maximum length: 2.080mm

Stainless steel back side.

Very suitable for exterior application.

Thickness: 16mm.

Maximum length: 2.350mm

ALUMINIUMThickness: 20mm - Maximum length: 2.080mm ex-cept silver anodized surrounds (3000 mm).

Includes corners that provide a greater strength to the surround and give a curved lines design. Available in lacquered finishes.

Silver anodized aluminium surround includes silver lac-quered corners, not anodized.

Very suitable for exterior application.

Aluminium back side.

Colour to select in page 45.

Oak veneer C-401Beech veneer C-407Sapelly veneer C-408

Ref. 4 pieces Finish

Gloss C-497 (4 pieces) / C-447 (4 pieces+back)Satin finished C-495 (4 pieces) / C-445 (4 pieces+back)

Ref. FinishGloss C-107 (4 pieces) / C-117 (4 pieces+back)Satin finished C-105 (4 pieces) / C-115 (4 pieces+back)

Ref. Finish

Lacquered C-350 (4 pieces) / C-370 (4 pieces+back)Silver anodized C-352 (4 pieces) / C-372 (4 pieces+back)

Ref. Acabado

52

ACCESSO

RIES

ACCESSORIES

RECTANGULAR STEEL BASE SUPPORT

RECTANGULAR STEEL SIDE SUPPORT

SUPPORTS

Material: Steel support with anti-corrosion cataphoretic protection.

Dimensions: 800 high x 50 wide x 100 depth.

To be screwed to the floor.

It is strictly recommended to use one support for each two columns of Mailboxes.

Recommended as a central support for banks with side supports that excedes from 1700 mm width.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Colour to select in page 45.

Ref. C-460 BASE

Material: Steel support with anti-corrosion cataphoretic protection.

Dimensions: 1500 high x 50 wide x 100 depth.

To be screwed to the floor.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Colour to select in page. 45

Ref. C-460 LATERAL

TUBULAR STAINLESS STEEL SIDE SUPPORTS

Material: Stainless steel.

Dimensions: 1500 high x ø84

To be screwed to the floor.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Ref. C-387

Rectangular steel base support

Rectangular steel side support

Tubular stainless steel side supports

1500

54

160

1500

250

150110

210

138

800

250

150110

210

53

ACC

ESSO

RIES

ACCESSORIES

OVAL ALUMINIUM SIDE SUPPORT

OVAL ALUMINIUM BASE SUPPORT

SUPPORTS

Material: Aluminium.

Dimensions: 1500 high x 40 wide x 120 depth.

To be screwed to the floor.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Colour to select in page. 45

Material: Aluminium.

Dimensions: 800 high x 40 wide x 120 depth.

To be screwed to the floor.

It is strictly recommended to use one support for each two columns of Mailboxes.

Recommended as a central support for banks with side supports that excedes from 1700 mm width.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Colour to select in page. 45 ALUMINIUM WALL FIXED SIDE SUPPORT Material: Aluminium.

Dimensions: 1800 high x 35 wide x 65 depth.

To be screwed to the floor and to the wall.

Innovative design which separates the bank of mailbo-xes flying from the wall up to 265 mm.

Suitable for vertical and horizontal Mailboxes.

Mailboxes must be banked with a surround in order to fix the suppports to it.

Aluminium wall fixed side support

Oval aluminium base support

Oval aluminium side support

120

160

100

120

60

160

100

120

60

1500

120

800

1800

265

o84/Lacquered colour to select C-590 Silver anodized C-592

Finish Ref.

Lacquered colour to select C-580 Silver anodized C-582

Finish Ref.

Silver anodized C-572 Oak melamine shelf C-570

Finish Ref.

54

ACCESSO

RIES

ACCESSORIES

TABLECHARACTERISTICSMaterial: Steel and stainless steel.

To be screwed to the floor.

An useful accessory as support for bank of mailboxes.

A new way to install the mailboxes on an entrance hall.

Suitable for all the references of mailboxes.

It is recommended to bank the mailboxes with a surround.

Colour to select on page 45

Ref. M15A10 M15A20 M15A30

STEEL COLOUR TO SELECT*See pg. 45

SATIN FINISHED STAINLESS STEEL

M15A20

M15A15 M15A25 M15A35

M15A30 M15A10

750

425 1000

750

425 2000

750

425 1500

Libro Mailboxes installed on a White lacquered table M15A20. Future Mailboxes installed on a silver lacquered table M15A20.

55

ACC

ESSO

RIES

ACCESSORIES

COLOUR TO SELECT STEEL

FLOOR SHELTER

WALL SHELTER

ROOF SHELTER

Material: Galvanized steel or stainless steel.

Design: Roof with even cantilever of 10 mm within the entire mailboxes group perimeter.

Maximum length: 2000mm.

In case the mailboxes are fastened to a wall, the roof will not have a cantilever on its rear part.

The roof is supplied fixed in the bank of mailboxes.

Mailboxes must be banked with a surround.

Suitable for all the references of mailboxes.

Colour to select on page 45

When the mailboxes are installed outside, exposed to inclement weather, the roof protects the mailboxes.

Material: Galvanized steel structure and transparent methacrylate roof.

Can be adapted to the dimensions of the bank of mailbo-xes to install inside.

Set of 2 supports colour to select. Ref. C-030 Intermediate support: Ref. C-031 (necessary from 1.500 mm).

Transparent methacrylate: Ref. C-032

Material: Stainless steel or galvanized steel structure and methacrylate roof.

Can be adapted to the dimensions of the bank of mailbo-xes to install inside.

OPTION 1: 30 cms depth roof.· Set of 2 framing square

OPTION 2: 50 cms depth roof.· Set of 2 framing square

Steel colour to select C-130 Gloss finished stainless steel C-137Satin finished stainless steel C-135

Finish Ref.

Colour to select steel C-033 Satin finished stainless steel C-033IS

Finish colour to select Ref.

Colour to select steel C-035 Satin finished stainless steel C-035IS

Finish colour to select Ref.

· Transparent methacrylate Ref. C-034

· Transparent methacrylate Ref. C-036