Assembly Instructions Item# L-GZ704PST GAZEBO ASSEMBLY INSTRUCTIONS Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final product will produce a quality shelter that will offer you years of enjoyment. All that is required is a screwdriver, a hammer and two ladders of at least 8 feet (2.5 m) high. (Not included). For you safety, DO NOT assemble this item alone. Two people or more are required for a smooth and safe installation. Item identification: For ease of identification, all parts are labeled to correspond to the Step number in which the part is used. Have six or more people helping you when assembling or moving the product.
Transcript
Assembly Instructions
Item# L-GZ704PST
GAZEBO ASSEMBLY INSTRUCTIONS Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final product will produce a quality shelter that will offer you years of enjoyment. All that is required is a screwdriver, a hammer and two ladders of at least 8 feet (2.5 m) high. (Not included). For you safety, DO NOT assemble this item alone. Two people or more are required for a smooth and safe installation. Item identification: For ease of identification, all parts are labeled to correspond to the Step number in which the part is used.
Have six or more people helping you when assembling
or moving the product.
Description Part Quantity Image
Short post A 2
Long post B 2
Small slanted beam C
4
Small connector D
1
Hook E 1
Small cover F1 2
Long cover 2 F2 2
Long cover 3 F3 2
Cover board G 4
Top cover board H 1
Big panel 1 I1 2
Big panel 2 I2 2
Small panel 1 I3 2
Small panel 2 I4 2
Fence I5 8
Connector J1 4
Top connector J2 4
Lower connector J3 4
Short beam 1 K1 2
Short beam 2 K2 2
Long beam 1 K3 2
Long beam 2 K4 2
Parts List
Description Part Quantity Image
Left netting tube 1 M1 2
Right netting tube 2 M2 2
Left netting tube 3 M3 2
Right netting tube 4 M4 2
Top slanted beam N1 4
Top post N2 4
Cover 1 O1 4
Cover 2 O2 2
Cover 3 O3 4
Cover 4 O4 2
Cover 5 O5 2
Cover 6 O6 2
Cover 7 O7 2
Cover 8 O8 2
Cover 9 P 2
Cover 10 Q 4
Beam 1 R1 2
Beam 2 R2 2
Beam 3 R3 2
Beam 4 R4 2
Beam 5 R5 2
Beam 6 R6 2
Long beam 1 S1 2
Long beam 2 S2 2
Description Part Quantity Image
Long beam 3 S3 2
Long beam 4 S4 2
Long beam 5 S5 2
Long beam 6 S6 2
Fixed beam 1 T1 2
Fixed beam 2 T2 2
Big fixed beam 1 U1 4
Big fixed beam 2 U2 2
Big fixed beam 3 U3 2
Top cover flap U4 2
Small top beam 1 V1 2
Small top beam 2 V2 2
Panel wall W 8
Mosquito net X 1
Part Description Quantity Image
AA M6 x 15 Bolt 64PCS
BB M6 Flat washer 124PCS
CC M6 x 65 Bolt 16PCS
DD M6 Nut 16PCS
EE M6 x 25 Bolt 12PCS
FF M6 x 35 Bolt 16PCS
Z M6 Wrench 2 PCS
Hardware Pack 1
Fig.1: Secure the fence (I5) to the panel with bolts (AA) and flat washers (BB).
Fig.5: Secure the connector (J1) to the beams with bolts (AA) and flat washers (BB).
Fig.2: Connect big panel 1 (I1) and small panel 1 (I3) with bolt (EE), flat washer (BB), repeat this for big panel 2 (I2) and small panel 2 (I4).
Fig.4: Attach long beam 1 (short beam 2) K3 (K2) / long beam 2 (short beam 1) K4 (K1) to I1 (I4) / I3 (I2) with bolts (FF), flat washers (BB), and bolts (AA), flat washers BB.
Fig.3: Insert short beam 1 / long beam 2 (K1) / (K4) into connection hole of short beam 2 / long beam 1 (K2) / (K3) and tighten with bolts (CC), flat washers (BB), nuts (DD).
Part Description Quantity Image
AA M6 x 15 Bolt 28PCS
BB M6 Flat washer 166PCS
LL ￠20 Flat washer 2PCS
HH M6 x 55 Screw 22PCS
DD M6 Nut 20PCS
I I M6 x 45 Bolt 8PCS
GG M6 x 15 Screw 88PCS
Hardware Pack 2
Fig.6: Secure the short post (A) with long post (B) with bolts (AA) and flat washers (BB).
Fig.7: Secure the small slanted beam（C） with bolts (AA) and flat washers (BB).
Fig.10: Secure the top end of the top slanted beam (N1) to the top frame with bolts (AA) and flat washers (BB).
Fig.8-1: Assemble the hook (E) to the small connector (D).
Fig.14: Assemble the cover board (G) to the small slanted beam (C) with bolts (II) and flat washers (BB). Assemble the top cover board (H) to the small connector (D) with screws (HH) and flat washers (BB & LL).
Fig.8: Assemble the small slanted beams (C) to the small connector (D) with nuts (DD), flat washers (BB) and screws (HH).
Fig.9: Secure the top slanted beam (N1) to the connector (J1) with screws (HH), flat washers (BB) and nuts (DD).
Fig.12: Secure the middle beam(N2) to the top frame with bolts (AA) and flat washers (BB).
Fig.11: Secure the lower end of the top post (N2) to the beam connector with screws (HH), flat washers (BB) and nuts (DD).
Fig.13: Assemble the long cover 2 (F2) to the long cover 3(F3), then secure the small cover (F1) and long covers (F2 and F3) to the small slanted beam with screws (GG) and flat washers (BB).
Fig.14-1: Secure the fixed beams (T1 and T2) to the covers (F1, F2 and F3) with screws (GG) flat washers (BB).
Fig.8-2: Secure the small top beams (V1 and V2) to the small slanted beam (C) with screws (GG) and flat washers (BB).
Part Description Quantity Image
AA M6 x 15 Bolt 2PCS
GG M6 x 15 Screw 48PCS
BB M6 Flat washer 58PCS
II M6 x 45 Bolt 8PCS
Hardware Pack 3
Fig.19-1: Secure one end of the netting tubes (M1，M2，M3，M4) to the top post (N2) with screws (GG) and flat washers (BB).
Fig.15: Secure the long beams (S1, S2, S3 and S4) to the top post (N2) with screws (GG) and flat washers (BB). Repeat this step to secure the beams (R1, R2, R3 and R4).
Fig.16: Secure the other end of the long beams (S1, S2, S3 and S4) to the top slanted beam (N1) with screws (GG) and flat washers (BB). Repeat this step to secure the beams (R1, R2, R3 and R4).
Fig.17: Secure the long beams (S5 and S6) to the top post (N2) with screws (GG) and flat washers (BB). Repeat this step to secure the beams (R5 and R6).
Fig.18: Secure the long beams (S5 and S6) to the top slanted beam (N1) with screws (GG) and flat washers (BB). Repeat this step to secure the beams (R5 and R6).
Fig.19-2: Secure the other end of the netting tubes (M1，M2，M3, M4) to the top slanted beam (N1) with screws (GG) and flat washers (BB).
Fig.20: Assemble the cover 3 (O3) on the cover 5 (O5). Repeat for this step to assemble cover 9 (P) and cover 3 (O3).
Fig.21: Secure the covers (O5 and P) to the top slanted beams (N1) with screws (GG) and flat washers (BB). Repeat this step to secure the cover 6 (O6).
Fig.22: Assemble the cover 1 (O1) to the cover 3 (O3) and assemble the cover 4 (O4) on the cover 2 (O2) with screws (GG) and flat washers (BB) to secure to the top slanted beams (N1).
Fig.23: Assemble the cover 7 (O7) on the cover 8 (O8) and assemble the cover 1 (O1) on the cover 3(O3) with screws (GG) and flat washers (BB) to secure to the top slanted beam (N1).
Fig.24: Secure the cover 10 (Q) to the beam with bolts (II) and flat washers (BB).
Part Description Quantity Image
JJ Φ8 x 260mm Stake 16PCS
KK Ring 67PCS
Hardware Pack 4
Fig.25-1: Secure top cover flap (U4) with bolt (AA) and flat washers (BB).
Fig.25: Put U1 onto the top of S5 (S6) and tighten them with GG, BB. And then, tighten U2 and the left side of R5 with GG, BB.Last, tighten U3 and the right side of R6 with GG and BB.
Fig.28: Secure the whole gazebo to the ground with stakes (JJ).
Fig.26: Assemble the panel wall (w) with velcro straps.
Fig.27: Hang the mosquito net (X) onto the netting tubes (M1, M2, M3 and M4) by using KK.
IMPORTANT: 1. Keep all children and pets away from assembly area. Children and pets should be supervised while gazebo is being assembled. 2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. 3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe assembly. 4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly. 5. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use. 6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in the ground. If you wish to secure the pavilion to a wood deck or concrete surface, use 16 anchors suited for these surfaces (anchors not included). 7. Check all bolts for tightness before and during usage. 8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installation and use. Some special procedures may be valid in your area. 9. While this gazebo is manufactured to withstand strong force winds through only the supplied ground stakes, securing the gazebo to a deck, concrete patio or a stronger base, in areas
subject to frequent severe weather should be considered. NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned off regularly. Any damage caused by snow accumulation is not covered by the warranty. Limited Warranty: This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item is maintained with care and used only for personal, residential purposes. The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.
Exclusions: Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.
Maintenance: Our iron/steel components for garden accessories and patio items are coated with rust inhibiting paint that protects it from rusting. However, due to the nature of iron, surface oxidation (rusting) will occur once these protective coatings are scratched. This is a natural process and is not a defect! To minimize this condition, we recommend care when assembling & handling the product to prevent scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily removed with a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or patio and cause damaging stains, which may be difficult to remove. This can be prevented if measure is taken to keep the product from oxidizing. Important: Please do not return this product to the store. For technical assistance on assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or Email [email protected] for assistance.
