ASTANOLOUVER SYSTEM FOR ATRIUMS (HARD TOP)

TP310

TP710

TP303

TP318

TP323-3/1

TP323-3/1

TP307

TP321

TP317-2

TP315

TP325

TP710

TP324

TP302

TP301

P732

P730

P733

P734

P735

TP323-4/2

TP320

CENTER PROFILEWITH GUTTER

CENTER PROFILECOVER

GUIDE PROFILE

DRIVE COVERFITTINGS

MOTOR DRIVE

HOLDER DRIVEFITTINGS

LATTERAL PROFILEWITH GUTTER

GUIDEPROFILE

CARRIERPROFILE

DRAIN PIPE CLAMP

BASE PLATE

TREADED BAR

ROOF DRAIN BEND 70º

CORNER COVER

END COVERFITTING

ROOF DRAINPIPE

END PROFILEWITH GUTTER

DRIP TRAYFITTINGS

CARRIERFITTINGS

CORNERCONNECTIONSET

CORNERCONNECTIONSET

CORNERCONNECTIONSET

INSTALLATION IS ONLY TO BE CARRIED OUT BY TRAINED SPECIALISTS. IT IS EXTREMELY IMPORTANT THAT THE SAFETY INSTRUCTIONS IN THE OPERATING MANUAL BE FOLLOWED.

1

1 1 1

432

TP7100 / TR4110Art. 252907 V08 2019-06-13© STOBAG AG www.stobag.com

EN 13561:2004+A1:2008

[inches]

[inches] [inches] [inches]

1“ = 25.4 mm1 mm = 0.039“

A

B

CD

1

2

3

4

1

2

3

5

4

TR4110 TR4110 TR4110

TP7100

2”2-5

/8”

2” 2-3/8” 2”

4”

4”

11-3/4”

max 25-5/8”

max 25-5/8”

4”

4”

11-3/4”

max 25-5/8”

max 25-5/8”

4”

4”

11-3/4”

max 25-5/8”

max 25-5/8”

4”

4”

11-3/4”

max 25-5/8”

max 25-5/8”

2-3/8”

2”

2-1

/2”

2-3

/8”

2-3

/8”

2-5

/8”

2-5

/8”

max. 1.5 Nm

8

10

13 14

11

12

9

6 75

1

1

1

1

1

1

2

2

2 2

2

23

33

[inches] TP7100 TP7100 TP7100

TP7100 TR4110 TR4110 TR4110[inches]

1

2

3

1

21

3

2

B

B

C

C

D

D

B

C

D

2-1

/2”

± 0 ± 0.04”

+ 1/8”

+ 1/8”

3”

3-1

/2”

1/2”

2-7

/8”

± 0

± 0

max. 1.5 Nm

15 16

1817

19 20

12

1

1

2

2

1

3

3

2

[inches] [inches]

[inches][inches]

TP7100 TP7100

TR4110TR4110

TR4110 TR4110

A

A

A

B

CD

1

2

3

4-3/8” 4”1-1/4” max 3/8”

4-3/4”

78-3/4” 99-3/8” 118-1/8” 137-3/4” 157-1/2” 177-1/8” 196-7/8” 216-1/2” 236-1/4” 255-7/8” 275-5/8”

12-1/4” 14-5/8” 15-3/4” 16-7/8” 18-1/8” 19-1/4” 20-1/2” 21-5/8” 22-7/8” 24” 25-1/4”

4-3/8” (n x 1.18”) + 3/8” 4”

3/8”

0 - max 3/8”

78-3/4” 99-3/8” 118-1/8” 137-3/4” 157-1/2” 177-1/8” 196-7/8” 216-1/2” 236-1/4” 255-7/8” 275-5/8”

12-1/4” 14-5/8” 15-3/4” 16-7/8” 18-1/8” 19-1/4” 20-1/2” 21-5/8” 22-7/8” 24” 25-1/4”

(n x 1.18”) + 3/8”

4”

max 25-5/8”

max 25-5/8”

max 25-5/8”