ASTANOLOUVER SYSTEM FOR ATRIUMS (HARD TOP)
TP310
TP710
TP303
TP318
TP323-3/1
TP323-3/1
TP307
TP321
TP317-2
TP315
TP325
TP710
TP324
TP302
TP301
P732
P730
P733
P734
P735
TP323-4/2
TP320
CENTER PROFILEWITH GUTTER
CENTER PROFILECOVER
GUIDE PROFILE
DRIVE COVERFITTINGS
MOTOR DRIVE
HOLDER DRIVEFITTINGS
LATTERAL PROFILEWITH GUTTER
GUIDEPROFILE
CARRIERPROFILE
DRAIN PIPE CLAMP
BASE PLATE
TREADED BAR
ROOF DRAIN BEND 70º
CORNER COVER
END COVERFITTING
ROOF DRAINPIPE
END PROFILEWITH GUTTER
DRIP TRAYFITTINGS
CARRIERFITTINGS
CORNERCONNECTIONSET
CORNERCONNECTIONSET
CORNERCONNECTIONSET
INSTALLATION IS ONLY TO BE CARRIED OUT BY TRAINED SPECIALISTS. IT IS EXTREMELY IMPORTANT THAT THE SAFETY INSTRUCTIONS IN THE OPERATING MANUAL BE FOLLOWED.
1
1 1 1
432
TP7100 / TR4110Art. 252907 V08 2019-06-13© STOBAG AG www.stobag.com
EN 13561:2004+A1:2008
[inches]
[inches] [inches] [inches]
1“ = 25.4 mm1 mm = 0.039“
A
B
CD
1
2
3
4
1
2
3
5
4
TR4110 TR4110 TR4110
TP7100
2”2-5
/8”
2” 2-3/8” 2”
4”
4”
11-3/4”
max 25-5/8”
max 25-5/8”
4”
4”
11-3/4”
max 25-5/8”
max 25-5/8”
4”
4”
11-3/4”
max 25-5/8”
max 25-5/8”
4”
4”
11-3/4”
max 25-5/8”
max 25-5/8”
2-3/8”
2”
2-1
/2”
2-3
/8”
2-3
/8”
2-5
/8”
2-5
/8”
max. 1.5 Nm
8
10
13 14
11
12
9
6 75
1
1
1
1
1
1
2
2
2 2
2
23
33
[inches] TP7100 TP7100 TP7100
TP7100 TR4110 TR4110 TR4110[inches]
1
2
3
1
21
3
2
B
B
C
C
D
D
B
C
D
2-1
/2”
± 0 ± 0.04”
+ 1/8”
+ 1/8”
3”
3-1
/2”
1/2”
2-7
/8”
± 0
± 0
max. 1.5 Nm
15 16
1817
19 20
12
1
1
2
2
1
3
3
2
[inches] [inches]
[inches][inches]
TP7100 TP7100
TR4110TR4110
TR4110 TR4110
A
A
A
B
CD
1
2
3
4-3/8” 4”1-1/4” max 3/8”
4-3/4”
78-3/4” 99-3/8” 118-1/8” 137-3/4” 157-1/2” 177-1/8” 196-7/8” 216-1/2” 236-1/4” 255-7/8” 275-5/8”
12-1/4” 14-5/8” 15-3/4” 16-7/8” 18-1/8” 19-1/4” 20-1/2” 21-5/8” 22-7/8” 24” 25-1/4”
4-3/8” (n x 1.18”) + 3/8” 4”
3/8”
0 - max 3/8”
78-3/4” 99-3/8” 118-1/8” 137-3/4” 157-1/2” 177-1/8” 196-7/8” 216-1/2” 236-1/4” 255-7/8” 275-5/8”
12-1/4” 14-5/8” 15-3/4” 16-7/8” 18-1/8” 19-1/4” 20-1/2” 21-5/8” 22-7/8” 24” 25-1/4”
(n x 1.18”) + 3/8”
4”
max 25-5/8”
max 25-5/8”
max 25-5/8”
