Tran
sfer
sw
itch
es
atys
_t_0
01_a
_1
ATyS t - ATyS gAutomatic Transfer Switching Equipmentfrom 125 to 3200 A
> Mains/mains applications (ATyS t)
> Mains/genset applications (ATyS g)
The solution for
> Rapid commissioning > ATyS d with integrated controller for functions dedicated to mains/mains or mains/genset applications
Strong points
Function
ATyS t and ATyS g are 3 or 4 pole automatic transfer switches, with positive break indication. They incorporate all the functions offered by the ATyS d, as well as functions intended for mains/mains applications (ATyS t) and mains/genset applications (ATyS g).In automatic mode they enable the monitoring of, and the on-load changeover between, two power supply sources, in accordance with the parameters configured via two potentiometers and four DIP switches.They are intended for use in low voltage power supply systems where a brief interruption of the load supply is acceptable during transfer.
Advantages
Rapid commissioningATyS t and g switches offer significant time saving during commissioning (process takes 2 to 3 minutes). Owing to the design that allows commissioning through just two potentiometers (4 on the ATyS g) and four DIP switches, a screwdriver is all that is required to configure the parameters.For added simplicity, they also offer an autoconfiguration function which enables automatic adjustment of the rated voltage and frequency.
ATyS t: specifically designed for mains/mains applicationsThe ATyS t’s integrated controller has been designed to provide only the functions required for these applications (operation with or without priority, preferred source selection) together with the monitoring of the voltage and frequency of both sources, for three-phase and single-phase networks.
ATyS g: specifically designed for mains/genset applicationsThe ATyS g’s integrated controller has been designed to provide specific functions for these applications (genset startup, on-load or off-load tests...) together with the monitoring of the voltage and frequency of both sources for three-phase and single-phase networks.The generator supply must be connected to switch II, located at the rear.
> IEC 60947-6-1 > IEC 60947-3 > GB 14048.11
Conformity to standards
atys
_g_0
01_a
Approvals and certifications(1)
(1) Product references on request.
B U R E A UV E R I T A S
ATyS t - ATyS gAutomatic Transfer Switching Equipment
from 125 to 3200 A
Rating (A) /Frame size No. of poles ATyS t ATyS g Bridging bars
Voltage sensing and power supply tap
Terminal shrouds
Terminal screens
Auxiliary contact
125 A / B33 P 9543 3012 9553 3012
3 P4109 3019
4 P4109 4019
3 P1559 3012
4 P1559 4012(1)
3 P2694 3014(2)
4 P2694 4014(2)
3 P1509 3012
4 P1509 4012
1599 0502
4 P 9543 4012 9553 4012
160 A / B33 P 9543 3016 9553 3016
4 P 9543 4016 9553 4016
200 A / B33 P 9543 3020 9553 3020
4 P 9543 4020 9553 4020
250 A / B43 P 9543 3025 9553 3025 4109 3025 1559 3025
3 P2694 3021(2)
4 P2694 4021(2)
3 P1509 3025
4 P1509 4025
4 P 9543 4025 9553 4025 4109 4025 1559 4025
315 A / B43 P 9543 3031 9553 3031
3 P4109 3039
4 P4109 4039
3 P1559 3040
4 P1559 4040
4 P 9543 4031 9553 4031
400 A / B43 P 9543 3040 9553 3040
4 P 9543 4040 9553 4040
500 A / B53 P 9543 3050 9553 3050 4109 3050
3 P1559 3063
4 P1559 4063
3 P2694 3051(2)
4 P2694 4051(2)
3 P1509 3063
4 P1509 4063
4 P 9543 4050 9553 4050 4109 4050
630 A / B53 P 9543 3063 9553 3063 4109 3063
4 P 9543 4063 9553 4063 4109 4063
800 A / B63 P 9543 3080 9553 3080
3 P4109 3080
4 P4109 4080
3 P1559 3080
4 P1559 4080
3 P1509 3080
4 P1509 4080
1599 0532
4 P 9543 4080 9553 4080
1000 A / B63 P 9543 3100 9553 3100
4 P 9543 4100 9553 4100
1250 A / B63 P 9543 3120 9553 3120 4109 3120 1559 3120
4 P 9543 4120 9553 4120 4109 4120 1559 4120
1600 A / B73 P 9543 3160 9553 3160 4109 3160 1559 3160 1509 3160
4 P 9543 4160 9553 4160 4109 4160 1559 4160 1509 4160
2000 A / B83 P 9543 3200 9553 3200
(1)
3 P1559 3200
4 P1559 4200
3 P1509 3200
4 P1509 4200
included
4 P 9543 4200 9553 4200
2500 A / B83 P 9543 3250 9553 3250
4 P 9543 4250 9553 4250
3200 A / B83 P 9543 3320 9553 3320
4 P 9543 4320 9553 4320
References ATyS t - ATyS g
(1) See "Copper bar connection pieces" (2) To fully shroud front, rear, top and bottom 4 references required.
To shroud front switch top and bottom 2 references required.
> Accessories: see > Characteristics: see > Terminals and connections: see > Dimensions: see
Technical information
446 General Catalogue 2017-2018
Tran
sfer
sw
itch
es
atys
_t_0
01_a
_1
ATyS t - ATyS gAutomatic Transfer Switching Equipmentfrom 125 to 3200 A
> Mains/mains applications (ATyS t)
> Mains/genset applications (ATyS g)
The solution for
> Rapid commissioning > ATyS d with integrated controller for functions dedicated to mains/mains or mains/genset applications
Strong points
Function
ATyS t and ATyS g are 3 or 4 pole automatic transfer switches, with positive break indication. They incorporate all the functions offered by the ATyS d, as well as functions intended for mains/mains applications (ATyS t) and mains/genset applications (ATyS g).In automatic mode they enable the monitoring of, and the on-load changeover between, two power supply sources, in accordance with the parameters configured via two potentiometers and four DIP switches.They are intended for use in low voltage power supply systems where a brief interruption of the load supply is acceptable during transfer.
Advantages
Rapid commissioningATyS t and g switches offer significant time saving during commissioning (process takes 2 to 3 minutes). Owing to the design that allows commissioning through just two potentiometers (4 on the ATyS g) and four DIP switches, a screwdriver is all that is required to configure the parameters.For added simplicity, they also offer an autoconfiguration function which enables automatic adjustment of the rated voltage and frequency.
ATyS t: specifically designed for mains/mains applicationsThe ATyS t’s integrated controller has been designed to provide only the functions required for these applications (operation with or without priority, preferred source selection) together with the monitoring of the voltage and frequency of both sources, for three-phase and single-phase networks.
ATyS g: specifically designed for mains/genset applicationsThe ATyS g’s integrated controller has been designed to provide specific functions for these applications (genset startup, on-load or off-load tests...) together with the monitoring of the voltage and frequency of both sources for three-phase and single-phase networks.The generator supply must be connected to switch II, located at the rear.
> IEC 60947-6-1 > IEC 60947-3 > GB 14048.11
Conformity to standards
atys
_g_0
01_a
Approvals and certifications(1)
(1) Product references on request.
B U R E A UV E R I T A S
ATyS t - ATyS gAutomatic Transfer Switching Equipment
from 125 to 3200 A
Rating (A) /Frame size No. of poles ATyS t ATyS g Bridging bars
Voltage sensing and power supply tap
Terminal shrouds
Terminal screens
Auxiliary contact
125 A / B33 P 9543 3012 9553 3012
3 P4109 3019
4 P4109 4019
3 P1559 3012
4 P1559 4012(1)
3 P2694 3014(2)
4 P2694 4014(2)
3 P1509 3012
4 P1509 4012
1599 0502
4 P 9543 4012 9553 4012
160 A / B33 P 9543 3016 9553 3016
4 P 9543 4016 9553 4016
200 A / B33 P 9543 3020 9553 3020
4 P 9543 4020 9553 4020
250 A / B43 P 9543 3025 9553 3025 4109 3025 1559 3025
3 P2694 3021(2)
4 P2694 4021(2)
3 P1509 3025
4 P1509 4025
4 P 9543 4025 9553 4025 4109 4025 1559 4025
315 A / B43 P 9543 3031 9553 3031
3 P4109 3039
4 P4109 4039
3 P1559 3040
4 P1559 4040
4 P 9543 4031 9553 4031
400 A / B43 P 9543 3040 9553 3040
4 P 9543 4040 9553 4040
500 A / B53 P 9543 3050 9553 3050 4109 3050
3 P1559 3063
4 P1559 4063
3 P2694 3051(2)
4 P2694 4051(2)
3 P1509 3063
4 P1509 4063
4 P 9543 4050 9553 4050 4109 4050
630 A / B53 P 9543 3063 9553 3063 4109 3063
4 P 9543 4063 9553 4063 4109 4063
800 A / B63 P 9543 3080 9553 3080
3 P4109 3080
4 P4109 4080
3 P1559 3080
4 P1559 4080
3 P1509 3080
4 P1509 4080
1599 0532
4 P 9543 4080 9553 4080
1000 A / B63 P 9543 3100 9553 3100
4 P 9543 4100 9553 4100
1250 A / B63 P 9543 3120 9553 3120 4109 3120 1559 3120
4 P 9543 4120 9553 4120 4109 4120 1559 4120
1600 A / B73 P 9543 3160 9553 3160 4109 3160 1559 3160 1509 3160
4 P 9543 4160 9553 4160 4109 4160 1559 4160 1509 4160
2000 A / B83 P 9543 3200 9553 3200
(1)
3 P1559 3200
4 P1559 4200
3 P1509 3200
4 P1509 4200
included
4 P 9543 4200 9553 4200
2500 A / B83 P 9543 3250 9553 3250
4 P 9543 4250 9553 4250
3200 A / B83 P 9543 3320 9553 3320
4 P 9543 4320 9553 4320
References ATyS t - ATyS g
(1) See "Copper bar connection pieces" (2) To fully shroud front, rear, top and bottom 4 references required.
To shroud front switch top and bottom 2 references required.
> Accessories: see > Characteristics: see > Terminals and connections: see > Dimensions: see
Technical information
447General Catalogue 2017-2018
page 453.
page 452.page 460.
page 462.page 464.