Date post: | 18-Jul-2016 |
Category: |
Documents |
Upload: | vi-king-pro |
View: | 217 times |
Download: | 4 times |
24 Opflow January 2013 www.awwa.org/opflow2013 © American Water Works Association 2013 © American Water Works Association
AWWA Standards 2013guidelines for the water community
SOURCEGroundwater and WellsA100-06 Water Wells
TREATMENTFiltrationB100-09 Granular Filter MaterialB101-01 Precoat Filter MediaB102-10 Manganese Greensand for
FiltersB110-09 Membrane Systems
SofteningB200-12 Sodium Chloride RevisedB201-08 Soda AshB202-07 Quicklime and Hydrated Lime
Disinfection ChemicalsB300-10 HypochloritesB301-10 Liquid ChlorineB302-10 Ammonium SulfateB303-10 Sodium ChloriteB304-08 Liquid Oxygen for Ozone
Generation for Water, Wastewater, and Reclaimed Water Systems
B305-06 Anhydrous AmmoniaB306-07 Aqua Ammonia (Liquid
Ammonium Hydroxide)
CoagulationB402-12 Ferrous Sulfate RevisedB403-09 Aluminum Sulfate—Liquid,
Ground, or LumpB404-08 Liquid Sodium SilicateB405-06 Sodium AluminateB406-06 Ferric SulfateB407-12 Liquid Ferric Chloride RevisedB408-10 Liquid Polyaluminum ChlorideB451-10 Poly(Diallyldimethylammonium
Chloride)B452-06 EPI-DMA PolyaminesB453-06 Polyacrylamide
Scale and Corrosion ControlB501-08 Sodium Hydroxide (Caustic
Soda)B502-11 Sodium Polyphosphate,
Glassy (Sodium Hexametaphosphate)
B503-11 Sodium TripolyphosphateB504-12 Monosodium Phosphate,
Anhydrous and Liquid RevisedB505-12 Disodium Phosphate,
Anhydrous RevisedB506-06 Zinc OrthophosphateB510-12 Carbon Dioxide RevisedB511-10 Potassium HydroxideB512-08 Sulfur DioxideB550-10 Calcium Chloride
Taste and Odor ControlB600-10 Powdered Activated CarbonB601-11 Sodium MetabisulfiteB602-08 Copper SulfateB603-10 PermanganatesB604-12 Granular Activated Carbon
RevisedB605-07 Reactivation of Granular
Activated Carbon
FluoridesB701-11 Sodium FluorideB702-11 Sodium FluorosilicateB703-11 Fluorosilicic Acid
PIPE AND ACCESSORIESDuctile-Iron Pipe and FittingsC104/A21.4-08 Cement–Mortar Lining
for Ductile-Iron Pipe and Fittings
C105/A21.10-10 Polyethylene Encasement for Ductile-Iron Pipe Systems
C110/A21.10-12 Ductile-Iron and Gray-Iron Fittings Revised
C111/A21.11-12 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings Revised
C115/A21.15-11 Flanged Ductile-Iron Pipe With Ductile-Iron or Gray-Iron Threaded Flanges
C116/A21.16-09 Protective Fusion-Bonded Epoxy Coatings for the Interior and Exterior Surfaces of Ductile-Iron and Gray-Iron Fittings
C150/A21.50-08 Thickness Design of Ductile-Iron Pipe
C151/A21.51-09 Ductile-Iron Pipe, Centrifugally Cast
C153/A21.53-11 Ductile-Iron Compact Fittings
Steel PipeC200-12 Steel Water Pipe, 6 In. (150
mm) and Larger RevisedC203-08 Coal-Tar Protective Coatings
and Linings for Steel Water Pipelines—Enamel and Tape—Hot-Applied
C205-12 Cement–Mortar Protective Lining and Coating for Steel Water Pipe—4 In. (100 mm) and Larger—Shop Applied Revised
C206-11 Field Welding of Steel Water Pipe
C207-07 Steel Pipe Flanges for Waterworks Service—Sizes 4 In. Through 144 In. (100 mm Through 3,600 mm)
C208-12 Dimensions for Fabricated Steel Water Pipe Fittings Revised
C209-06 Cold-Applied Tape Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines
C210-07 Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines
C213-07 Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines
C214-07 Tape Coating Systems for the Exterior of Steel Water Pipelines
awwa standards are vital guidelines for all facets of the water community. they provide the mini-mum requirements for design, installation, performance, and manufacturing of products used in the water industry. there’s also a series covering utility management. each standard designation consists of two elements connected by a hyphen, such as B200-07, which indicates the stan-dard is in the 200 series (softening) and received awwa board of directors approval in 2007. new standards may be first editions or revisions of existing standards. awwa standards are also adopted as ansi standards. contact the awwa store, www.awwa.org/store, 800.926.7337, or [email protected]. watch the awwa website or Journal - American Water Works Association for official notice of new standards or any status changes to existing standards.
www.awwa.org/opflow January 2013 Opflow 252013 © American Water Works Association 2013 © American Water Works Association
C215-10 Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines
C216-07 Heat-Shrinkable Cross-Linked Polyolefin Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines
C217-09 Petrolatum and Petroleum Wax Tape Coatings for the Exterior of Connections and Fittings for Steel Water Pipelines
C218-08 Liquid Coating Systems for the Exterior of Aboveground Steel Water Pipelines and Fittings
C219-11 Bolted, Sleeve-Type Couplings for Plain-End Pipe
C220-12 Stainless-Steel Pipe, ½ In. (13 mm) and Larger Revised
C221-12 Fabricated Steel Mechanical Slip-Type Expansion Joints Revised
C222-08 Polyurethane Coatings for the Interior and Exterior of Steel Water Pipe and Fittings
C223-07 Fabricated Steel and Stainless Steel Tapping Sleeves
C224-11 Nylon-11-Based Polyamide Coating System for the Interior and Exterior of Steel Water Pipe, Connections, Fittings, and Special Sections
C225-07 Fused Polyolefin Coating Systems for the Exterior of Steel Water Pipelines
C226-06 Stainless-Steel Fittings for Waterworks Service, Sizes ½ In. Through 72 In. (13 mm Through 1,800 mm)
C227-11 Bolted, Split-Sleeve Restrained and Nonrestrained Couplings for Plain-End Pipe
C228-08 Stainless-Steel Pipe Flanges for Water Service—Sizes 2 In. Through 72 In. (50 mm Through 1,800 mm)
C229-08 Fusion-Bonded Polyethylene Coating for the Exterior of Steel Water Pipelines
C230-11 Stainless-Steel Full-Encirclement Repair and Service Connection Clamps
Concrete PipeC300-11 Reinforced Concrete Pressure
Pipe, Steel-Cylinder TypeC301-07 Prestressed Concrete Pressure
Pipe, Steel-Cylinder TypeC302-11 Reinforced Concrete Pressure
Pipe, Noncylinder TypeC303-08 Concrete Pressure Pipe, Bar-
Wrapped, Steel-Cylinder TypeC304-07 Design of Prestressed Concrete
Cylinder Pipe
Valves and HydrantsC500-09 Metal-Seated Gate Valves for
Water Supply Service C502-05 Dry-Barrel Fire HydrantsC503-05 Wet-Barrel Fire HydrantsC504-10 Rubber-Seated Butterfly
Valves, 3 In. (75 mm) Through 72 In. (1,800 mm)
C507-11 Ball Valves, 6 In. Through 60 In. (150 mm Through 1,500 mm)
C508a-12 Addenda to C508-09, Swing-Check Valves for Waterworks Service, 2-In. through 24-In. (50-mm through 600-mm) NPS Revised
C508-09 Swing-Check Valves for Waterworks Service, 2-In. Through 24-In. (50-mm Through 600-mm) NPS
C509-09 Resilient-Seated Gate Valves for Water Supply Service
C510-07 Double Check Valve Backflow Prevention Assembly
C511-07 Reduced-Pressure Principle Backflow Prevention Assembly
C512-07 Air-Release, Air/Vacuum, and Combination Air Valves for Waterworks Service
C515-09 Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service
C516-10 Large-Diameter Rubber-Seated Butterfly Valves, Sizes 78 In. (2,000 mm) and Larger
C517-09 Resilient-Seated Cast-Iron Eccentric Plug Valves
C518-08 Dual-Disc Swing-Check Valves for Waterworks Service
C520-10 Knife Gate Valves, Sizes 2 In. (50 mm) Through 96 In. (2,400 mm)
C530-12 Pilot-Operated Control Valves Revised
C541-08 Hydraulic and Pneumatic Cylinder and Vane-Type Actuators for Valves and Slide Gates
C542-09 Electric Motor Actuators for Valves and Slide Gates
C550-05 Protective Interior Coatings for Valves and Hydrants
C560-07 Cast-Iron Slide GatesC561-12 Fabricated Stainless-Steel Slide
Gates RevisedC562-12 Fabricated Aluminum Slide
Gates NewC563-12 Fabricated Composite Slide
Gates
PIPE INSTALLATIONC600-10 Installation of Ductile-
Iron Mains and Their Appurtenances
C602-11 Cement–Mortar Lining of Water Pipelines in Place—4 In. (100 mm) and Larger
C604-11 Installation of Buried Steel Water Pipe—4 In. (100 mm) and Larger
C605-05 Underground Installation of Polyvinyl Chloride (PVC) Pressure Pipe and Fittings for Water
C606-11 Grooved and Shouldered Joints
C620-07 Spray-Applied In-Place Epoxy Lining of Water Pipelines, 3 In. (75 mm) and Larger
DISINFECTION OF FACILITIESC651-05 Disinfecting Water MainsC652-11 Disinfection of Water-Storage
FacilitiesC653-03 Disinfection of Water
Treatment Plants
26 Opflow January 2013 www.awwa.org/opflow2013 © American Water Works Association 2013 © American Water Works Association
AWWA Standards 2013
C654-03 Disinfection of WellsC655-09 Field DechlorinationC670-09 Online Chlorine Analyzer
Operation and Maintenance
METERSC700-09 Cold-Water Meters—
Displacement Type, Bronze Main Case
C701-12 Cold-Water Meters—Turbine Type, for Customer Service Revised
C702-10 Cold-Water Meters—Compound Type
C703-11 Cold-Water Meters—Fire-Service Type
C704-12 Propeller-Type Meters for Waterworks Applications Revised
C706-10 Direct-Reading, Remote-Registration Systems for Cold-Water Meters
C707-10 Encoder-Type Remote-Registration Systems for Cold-Water Meters
C708-11 Cold-Water Meters—Multijet Type
C710-09 Cold-Water Meters—Displacement Type, Plastic Main Case
C712-10 Cold-Water Meters—Singlejet Type
C713-10 Cold-Water Meters—Fluidic-Oscillator Type
C750-10 Transit-Time Flowmeters in Full Closed Conduits
SERVICE LINESC800-05 Underground Service Line
Valves and Fittings
PLASTIC PIPEC900-07 Polyvinyl Chloride (PVC)
Pressure Pipe and Fabricated Fittings, 4 In. Through 12 In. (100 mm Through 300 mm), for Water Transmission and Distribution
C901-08 Polyethylene (PE) Pressure Pipe and Tubing, ½ In. (13 mm) Through 3 In. (76 mm), for Water Service
C903-05 Polyethylene–Aluminum–Polyethylene & Cross-linked Polyethylene–Aluminum–Cross-linked Polyethylene Composite Pressure Pipes, ½ In. (12 mm) Through 2 In. (50 mm), for Water Service
C904-06 Cross-Linked Polyethylene (PEX) Pressure Pipe, ½ In. (12 mm) Through 3 In. (76 mm), for Water Service
C905-10 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 14 In. Through 48 In. (350 mm Through 1,200 mm)
C906-07 Polyethylene (PE) Pressure Pipe and Fittings, 4 In. (100 mm) Through 63 In. (1,600 mm), for Water Distribution and Transmission
C907-12 Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 In. Through 12 In. (100 mm Through 300 mm), for Water, Wastewater, and Reclaimed Water Service Revised
C909-09 Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4 In. Through 24 In. (100 mm Through 600 mm), for Water Distribution
C950-07 Fiberglass Pressure Pipe
STORAGED100-11 Welded Carbon Steel Tanks for
Water StorageD102-11 Coating Steel Water-Storage
TanksD103-09 Factory-Coated Bolted Carbon
Steel Tanks for Water StorageD104-11 Automatically Controlled,
Impressed-Current Cathodic Protection for the Interior Submerged Surfaces of Steel Water Storage Tanks
D106-10 Sacrificial Anode Cathodic Protection Systems for the Interior Submerged Surfaces of Steel Water Storage Tanks
D107-10 Composite Elevated Tanks for Water Storage
D108-10 Aluminum Dome Roofs for Water Storage Facilities
D110-04 Wire- and Strand-Wound, Circular, Prestressed Concrete Water Tanks
D115-06 Tendon-Prestressed Concrete Water Tanks
D120-09 Thermosetting Fiberglass-Reinforced Plastic Tanks
D121-12 Bolted Aboveground Thermosetting Fiberglass-Reinforced Plastic Panel-Type Tanks for Water Storage Revised
D130-11 Geomembrane Materials for Potable Water Applications
PUMPSE102-06 Submersible Vertical Turbine
PumpsE103-07 Horizontal and Vertical Line-
Shaft Pumps with Errata incorporated
PLANT EQUIPMENTF101-07 Contact-Molded, Fiberglass-
Reinforced Plastic Wash-Water Troughs and Launders
F102-07 Matched-Die-Molded, Fiberglass-Reinforced Plastic Weir Plates, Scum Baffles, and Mounting Brackets
F110-12 Ultraviolet Disinfection Systems for Drinking Water New
UTILITY MANAGEMENTG100-11 Water Treatment Plant
Operation and ManagementG200-09 Distribution Systems
Operation and ManagementG300-07 Source Water Protection G400-09 Utility Management SystemG410-09 Business Practices for
Operation and ManagementG420-09 Communications and
Customer RelationsG430-09 Security Practices for
Operation and ManagementG440-11 Emergency Preparedness
Practices