◗ AAstragal Weatherstrip . . . . . . . . 52
◗ BBack Plate-Strap Hinge . . . . . . . 62Binder, Steel . . . . . . . . . . . . . . . 33Bolts, Cane . . . . . . . . . . . . . . . . 37Bolts, Cremone . . . . . . . . . . 38-41Bolts, Spring . . . . . . . . . . . . . . 37Bow Handles . . . . . . . . . . . . . . . 31Brackets, Handrail . . . . . . . . . . . 53Bumper Shoes. . . . . . . . . . . . . . 33
◗ CCane Bolts . . . . . . . . . . . . . . . . . 37Cremone Bolts . . . . . . . . . . . 38-41Curtain Hangers. . . . . . . . . . . 7, 13Curves-2035 series . . . . . . . . . . 15
◗ DDoor Holder . . . . . . . . . . . . . . . 34Door Guides . . . . . . . . . . . . . . . 34Door Latches . . . . . . . . . . . . 35, 36Door Stops . . . . . . . . . . . . . 33, 34Door Top Plate . . . . . . . . . . . . . . 9
◗ EEnd Stop, Door . . . . . . . . . . . . . 33
◗ FFlat Track Truck/Hanger . . . . . . 28Floor Center Guides . . . . . . . . . 34Floor Door Guides . . . . . . . . 32,34Flush Pulls. . . . . . . . . . . . . . . . . 30Fusible Links . . . . . . . . . . . . . . . 51
◗ GGuide Rollers. . . . . . . . . . . . . . . 29Guides, Door . . . . . . . . . . . . 32, 34Guide Roller Strip . . . . . . . . . . . 32
◗ HHandle, Bow . . . . . . . . . . . . . . . 31Handrail Brackets . . . . . . . . . . . 53Hasps . . . . . . . . . . . . . . . . . . . . 31Hinge Selection Guide . . . . . 54, 55Hinges . . . . . . . . . . . . . . . . . 56-62Holder, Door . . . . . . . . . . . . . . . 34
◗ KKeepers, Spring Bolt . . . . . . . . . 37
◗ LLatches . . . . . . . . . . . . . . . . 35, 36Links, Fusible . . . . . . . . . . . . . . 51Lock Joint® Brackets . . . . . . . . . . 3Lock Joint® Track. . . . . . . . . . . . . 4Lock Joint® Truck/Hanger . . . . . . 5
◗ NNeoprene Weatherstrip . . . . . . . 52
◗ OOverhead Brackets-31 Series . . . 8Overhead Brackets-232 Series . 11Overhead Brackets-330 Series . 17Overhead Brackets-2035 Series . 14Overhead Brackets-376 Series . 20Overhead Brackets-888 Series . 23
◗ PPulls, Flush . . . . . . . . . . . . . . . . 30Padlock Staple . . . . . . . . . . . . . 35
◗ SSets, Slide/Fold Doors. . . . . 44, 45Sets, Single/Bi-Parting . . . . 42, 43Sidewall Brackets-31 Series . . . . 8Sidewall Brackets-232 Series . . 11Sidewall Brackets-330 Series . . 17Sidewall Brackets-2035 Series . 14Sidewall Brackets-376 Series . . 20Sidewall Brackets-888 Series . . 23Spring Bolts . . . . . . . . . . . . . . . 37Stainless Steel Track-31 Series . 26Stainless Steel Track-232 Series. . 26Stainless Steel Hardware. . . 26, 27Steel Binder . . . . . . . . . . . . . . . . 33Strap Hinge Back Plate . . . . . . . 62Strap Hinge Selection Guide. . 54-57Strap Hinges, Industrial . . . . 60-62Strap Hinges, Standard . 56, 58-59Sweep Weatherstrip . . . . . . . . . 52
◗ TTop Plate . . . . . . . . . . . . . . . . . . . 9Track Curves-2035 Series . . . . . 15Track Section-31 Series. . . . . . . . 7Track Section-232 Series. . . . . . 10Track Section-330 Series. . . . . . 16Track Section-2035 Series. . . . . 13Track Section-376 Series. . . . . . 19Track Section-888 Series. . . . . . 22Truck/Hanger-31 Series . . . . . . . . 9Truck/Hanger-232 Series . . . . . . 12Truck/Hanger-330 Series . . . . . . 18Truck/Hanger-2035 Series . . . . . 13Truck/Hanger-376 Series . . . . . . 21Truck/Hanger-888 Series . . . 24, 25
◗ WWarranty . . . . . . . . . . . . . . . . . . 63Weatherstrip . . . . . . . . . . . . . . . 52Weld/Jig Kit 2035 Track. . . . . . . 14Weld/Lube Kit 888 Track . . . . . . 22
ALPHABETICAL INDEX
Model No. Name Page31 . . . . . . . . . Brackets . . . . . . . . . . . . . . . . 831 . . . . . . . . . Track . . . . . . . . . . . . . . . . . . . 7
31 . . . . . . . . . Hanger/Truck. . . . . . . . . . . . . 931 . . . . . . . . . Stainless Track . . . . . . . . . . 2631 . . . . . . . . . Stainless Hanger . . . . . . . . . 2631 . . . . . . . . . Stainless Truck . . . . . . . . . . 2631 . . . . . . . . . Brackets, Stainless . . . . . . . 2754 . . . . . . . . . Stay Roller . . . . . . . . . . . . . 2958 . . . . . . . . . Stay Roller . . . . . . . . . . . . . 2958 . . . . . . . . . Stay Roller, Stainless . . . . . 2659 . . . . . . . . . Stay Roller . . . . . . . . . . . . . 2970 . . . . . . . . . Flush Pull . . . . . . . . . . . . . . 3071 . . . . . . . . . Bow Handle. . . . . . . . . . . . . 3172 . . . . . . . . . Flush Pull, Stainless . . . . . . 2681 . . . . . . . . . Bow Handle. . . . . . . . . . . . . 3182 . . . . . . . . . Binder . . . . . . . . . . . . . . . . . 33
82 . . . . . . . . . Binder, Stainless . . . . . . . . . 2683 . . . . . . . . . Bow Handle, Stainless . . . . 26
89 . . . . . . . . . Binder Stop . . . . . . . . . . . . . 3397 . . . . . . . . . Fusible Link. . . . . . . . . . . . . 51102 . . . . . . . . Bumper Shoe . . . . . . . . . . . 33102 . . . . . . . . Binder . . . . . . . . . . . . . . . . . 33102 . . . . . . . . Flat Track Hanger . . . . . . . . 28119 . . . . . . . . Door Holder . . . . . . . . . . . . 34125 . . . . . . . . Latch . . . . . . . . . . . . . . . . . . 35128 . . . . . . . . Latch . . . . . . . . . . . . . . . . . . 35128 . . . . . . . . Padlock Staple . . . . . . . . . . 35
152 . . . . . . . . Latch . . . . . . . . . . . . . . . . . . 36153 . . . . . . . . Stay Roller . . . . . . . . . . . . . 29154 . . . . . . . . Stay Roller . . . . . . . . . . . . . 29
171 . . . . . . . . Floor Stop . . . . . . . . . . . . . . 34182 . . . . . . . . Hasp . . . . . . . . . . . . . . . . . . 31191 . . . . . . . . Bow Handle. . . . . . . . . . . . . 31216 . . . . . . . . Astragal Weatherstrip . . . . . 52216 . . . . . . . . Sweep Weatherstrip . . . . . . 52225 . . . . . . . . Latch . . . . . . . . . . . . . . . . . 36232 . . . . . . . . Track . . . . . . . . . . . . . . . . . . 10232 . . . . . . . . Brackets . . . . . . . . . . . . . . . 11232 . . . . . . . . Hanger/Truck. . . . . . . . . . . . 12232 . . . . . . . . Truck/Hanger, Stainless. . . . 26232 . . . . . . . . Track, Stainless . . . . . . . . . . 26232 . . . . . . . . Brackets, Stainless . . . . . . . 27330 . . . . . . . . Brackets . . . . . . . . . . . . . . . 17330 . . . . . . . . Track . . . . . . . . . . . . . . . . . . 16
Model No. Name Page330 . . . . . . . . Hanger/Truck. . . . . . . . . . . . 18376 . . . . . . . . Bracket . . . . . . . . . . . . . . . . 20376 . . . . . . . . Track . . . . . . . . . . . . . . . . . . 19434 . . . . . . . . Hardware Sets . . . . . 44, 49-50434 . . . . . . . . Hinges . . . . . . . . . . . . . . 60-62434 . . . . . . . . Hinge Back Plate . . . . . . . . . 62434 . . . . . . . . Spring Bolts . . . . . . . . . . . . 37434 . . . . . . . . Keeper. . . . . . . . . . . . . . . . . 37435 . . . . . . . . Hanger . . . . . . . . . . . . . . . . 48470 . . . . . . . . Flush Pull . . . . . . . . . . . . . . 30514 . . . . . . . . Spring Bolts . . . . . . . . . . . . 37524 . . . . . . . . Cane Bolt . . . . . . . . . . . . . . 37535 . . . . . . . . Flush Pull . . . . . . . . . . . . . . 30566 . . . . . . . . Handrail Bracket . . . . . . . . . 53572 . . . . . . . . End Stop . . . . . . . . . . . . . . . 33647 . . . . . . . . Guide Roller Strip . . . . . . . . 32739 . . . . . . . . Floor Guide . . . . . . . . . . . . . 32739 . . . . . . . . Floor Guide Track . . . . . . . . 32771 . . . . . . . . Door Guide . . . . . . . . . . . . . 34888 . . . . . . . . Bracket . . . . . . . . . . . . . . . . 23888 . . . . . . . . Track . . . . . . . . . . . . . . . . . . 22888 . . . . . . . . Hanger/Truck . . . . . . . . 24, 25888 . . . . . . . . Weld/Lube Kit . . . . . . . . . . . 221025 . . . . . . . Latch . . . . . . . . . . . . . . . . . . 361028 . . . . . . . Heavy-duty Cremone
Bolt . . . . . . . . . . . . . . . . 38, 391028 . . . . . . . Extra Heavy-duty
Cremone Bolt . . . . . . . . 40, 411035 . . . . . . . Hardware Sets . . . . . . . . 45-481035 . . . . . . . Hinge Back Plate . . . . . . . . . 621035 . . . . . . . Strap Hinges . . . . . . . . . . . . 581036 . . . . . . . Hinge Back Plate . . . . . . . . . 621036 . . . . . . . Strap Hinges . . . . . . . . . . . . 581040 . . . . . . . Strap Hinges . . . . . . . . . . . . 591047 . . . . . . . Strap Hinges . . . . . . . . . . . . 591600 . . . . . . . Hardware Sets . . . . . . . 42, 432035 . . . . . . . Brackets . . . . . . . . . . . . . . . 142035 . . . . . . . Curved Track . . . . . . . . . . . . 152035 . . . . . . . Track . . . . . . . . . . . . . . . . . . 132035 . . . . . . . Hanger/Truck. . . . . . . . . . . . 132035 . . . . . . . Welding Jig . . . . . . . . . . . . . 142434 . . . . . . . Truck/Hanger . . . . . . . . 49, 502600 . . . . . . . Hardware Sets . . . . . . . 42, 433110 . . . . . . . Top Plate . . . . . . . . . . . . . . . . 93110 . . . . . . . Truck/Hanger. . . . . . . . . . . . . 93120 . . . . . . . Truck/Hanger. . . . . . . . . . . . . 93130 . . . . . . . Utility/Hanger . . . . . . . . . . . . 73140 . . . . . . . Utility/Hanger . . . . . . . . . . . . 7
NUMERICAL INDEX
◗ Standard of the IndustryManufacturing since 1880 in Aurora, IL . . . . . . . . . . most experience in the industryStandard capacities up to 5000 pounds . . . . . . . . . . heaviest in the industryStandard 10 Year Warranty . . . . . . . . . . . . . . . . . . . . longest in the industryStandard Industrial Strength . . . . . . . . . . . . . . . . . . . highest quality designs
◗ Complete Product LineSix Track designs and capacities to cover all applications
a. 400, 600, 800, 1000, 2500, and 5000 pound standard capacitiesb. 16 gauge to 3/16" constructionc. Bare, Powder Coated, Galvanized, Stainless, or Plated Finishesd. Curves, Switches, Turntables and Crossovers availablee. Richards-Wilcox Patented Lock-Joint Concept
◗ Positive interlocking track joint brackets◗ Prevents horizontal track slippage or separation◗ Easy mechanical installations without welding
f. 10 Hanger Designs◗ Sidewall Mounting◗ Overhead Mounting
g. 12 Truck/Hanger Designs◗ Ball, Caged Roller and Polymer Bearing◗ Adjustable Aprons for differing door thicknesses
Industrial Strap Hingesa. Two Designs--standard and heavy dutyb. Ball and Disc Bearings for different loading needsc. Up to 1/2" thick materiald. Standard strap lengths up to 36"—longer lengths availablee. Decorative designs and finishes availablef. Complete offering with accessories
Accessories and Related Items—all with various designs and finishesa. Latchesb. Stay Rollersc. Door Stopsd. Bow Handlese. Flush Pullsf. Cremone, Cane, and Spring Boltsg. Fire Door Fusible Linksh. Handrail Bracketsi. Industrial Curtain Hangersj. Weather Stripping and Sweep Sets
RICHARDS-WILCOX HARDWARE ADVANTAGES
1
RICHA
RDS-
WILCO
X HAR
DWAR
E ADV
ANTAG
ES
2
Pre-Engineered and Packaged Hardware Sets a. All items are included—track, hangers, truck/hanger assemblies, handles, floor guides, door
bolts, drawings, etc.b. Simple part number ordering simplec. Single and Bi-Parting Door Setsd. Slide and Slide-Fold Door Sets
Strong Regional Stocking Distributor Network a. Extensive Experienceb. Factory Trainedc. Same Day Shipments with In-house Inventoriesd. Completely Service Oriented
◗ Proven Applications Since 1880Doors Industrial Applications Stainless Steel ApplicationsLarge Warehouse Doors Rolling Mill Access Doors MarineVehicle Maintenance Shop Doors Industrial Oven Doors Pulp MillWoven Wire Doors Solvent Tool/Parts Cleaning Tanks ChemicalTool Crib Doors Paint Booth Access Doors PharmaceuticalAirplane Hanger Doors Welding Curtains Food ProcessingCooler Doors Portable Tool Carriers Plating/FinishingSliding Strip Doors Around-the-Corner DoorsLead and Bulletproof Doors Freezer DoorsClassroom Doors
Animal Control Display PanelsZoo Doors and Gates Art GalleriesAnimal Holding Areas MuseumsCrowding Doors and Gates Chalkboards and TackboardsBarn Doors and Stalls ShowroomsMetal and Pole Building Doors Boardrooms
Trucks SecurityDisplay Truck Doors Prison Gates and DoorsTrailer Doors SallyportsCargo Restraining Curtains Commercial Swing/Slide gates
Theater Staging MiscellaneousAcoustical Panels Sliding Room DividersStage Reducing Panels Operable WallsStage Curtains Athletic Dressing/Equipment DryingStage Light Rigging Weapon Target Carriers
The unique design of the Richards-Wilcox Lock-Joint® Track and Brackets prevents the horizontal creepof tracks while binding them together tightly against the bottom of the bracket. This achieves a smoothtight joint for the hanger runway. The Standard Product guarantee requires the use of Track Brackets forall applications.
◗ Center BracketsSlide track through center sidewall/overhead brackets. Provides supportof track and track lips at required support intervals.
◗ Center Stop BracketsSlide each end of each track fully into centersidewall stop bracket. Provides track supportand door stop at center of bi-parting door instal-lations.
◗ Lock-Joint BracketsLoosen nut “A”, raise clamp “B”, slide tracks intobracket, drop bent ends of clamp “B” into holes intops of track and tighten nut “A”. Provides the uniqueLock-Joint feature between track sections.
NOTE #1: 888 Track joints must be welded on all man-ual 2500 to 5000 lb. applications and all poweredapplications. See page 22 for welding kit information.
◗ End BlindPlace end blind over end of track and slide track, and endblind fully into center sidewall/overhead bracket. Providesstop to prevent creep on one-piece track applications. Closesend of track to birds.
LOCK-JOINT ®BOX TYPE TRACK AND BRACKETS• Installation and Functions
3
TRACK
DATA
4
*Capacity Standardfor Doors Inside Available Finish/ Galvanized Hot-dipped Stainless PoundWeighing Track Dimensions Lengths Powder Steel Galvanized Steel per__ Pounds Number Gauge in Inches Feet Coat Available Available Available Foot
◗ Lock-Joint® Style Track – Manually Operated1w" Wide 6', 8', 10'
400 31 16 22" High 12' & 20' Painted X X 1w
27/32" Wide600 232 14 34" High 6', 8', 10' Painted X X 2w
1w" Wide600 2035 7 2c" High 10' Painted X X 5
2s" Wide800 330 13 34" High 6', 8', 10' Painted X 4
2s" Wide1000 376 10 34" High 6', 8', 10' Painted X 5w
2m" Wide1500** 888 9 29/32" High 6', 8', 10' Painted X 8
2m" Wide2500*** 888 9 29/32" High 6', 8', 10' Painted X 8
2m" Wide5000**** 888 9 29/32" High 6', 8', 10'' Painted X 8
◗ Lock-Joint® Style Track – Power Operated2s" Wide
800 376 10 34" High 6', 8', 10' Painted X 5w
2m" Wide1500** 888 9 29/32" High 6', 8', 10' Painted X 8
2m" Wide2500*** 888 9 29/32" High 6', 8', 10' Painted X 8
2m" Wide5000**** 888 9 29/32" High 6', 8', 10'' Painted X 8
* With pair of truck/hanger assemblies per door.** 1500 lb. capacity when 888 track is used with 8880.00001 trucks.*** 2500 lb. capacity when 888 track is used with 8881.00001 trucks.**** 5000 lb. capacity when 888 track is used with 8881.00017 trucks.
DOOR TRUCK / APRON ASSEMBLY DATA
5
*Capacity for Doors Door Part Track Type TypeWeighing __ Pounds Thickness Number Number Aprons Bearing
◗ Lock-Joint® Style Track – Manually Operated400 12" to 24" 3120.00002 31 Zinc Plated Delrin400 12" to 24" 3110.00002 31 Zinc Plated Roller
600 1w" to 24" 2320.00002 232 Painted Roller600 1w" to 24" 2320.00003 232 Zinc Plated Roller600 24" to 2w" 2320.00004 232 Painted Roller600 24" to 2w" 2320.00005 232 Zinc Plated Roller600 1w" to 24" 2321.00002 232 Painted Ball600 1w" to 24" 2321.00003 232 Zinc Plated Ball600 24" to 2w" 2321.00004 232 Painted Ball600 24" to 2w" 2321.00005 232 Zinc Plated Ball600 Per Application 2035.01975 2035 Painted Ball
800 1w" to 24" 3300.00002 330 Painted Roller800 24" to 3" 3300.00004 330 Painted Roller800 1w" to 24" 3301.00002 330 Painted Ball800 24" to 3" 3301.00004 330 Painted Ball
1000 1w" to 24" 3300.00002 376 Painted Roller1000 24" to 3" 3300.00004 376 Painted Roller1000 1w" to 24" 3301.00002 376 Painted Ball1000 24" to 3" 3301.00004 376 Painted Ball
1500 1w" to 24" 8880.00002 888 Painted Ball1500 24" to 3" 8880.00004 888 Painted Ball
2500 24" to 3" 8881.00002 888 Painted Ball5000 Per Application 8881.00017 888 — Ball
◗ Lock-Joint® Style Track – Power Operated800 1w" to 24" 3761.00002 376 Painted Ball800 24" to 3" 3761.00004 376 Painted Ball
1500 1w" to 24" 8880.00002 888 Painted Ball1500 24" to 3" 8880.00004 888 Painted Ball
2500 24" to 3" 8881.00002 888 Painted Ball
5000 Per Application 8881.00017 888 — Ball
*With pair of truck/hanger assemblies per door.
INSTAL
LATIO
N COM
PONE
NT QU
ANTIT
IES FO
R TRA
CK SE
RIES
6
Track End Lock Double End Double LockSeries Capacity Center Blind Joint* Center Blind Joint
◗ Sidewall Mounting31 Track 400#6 Foot Section 4 2 1 4 4 18 Foot Section 5 2 1 5 4 110 Foot Section 6 2 1 6 4 112 Foot Section 7 2 1 7 4 120 Foot Section 11 2 1 11 4 1232 Track 600#6 Foot Section 4 2 1 4 4 18 Foot Section 5 2 1 5 4 110 Foot Section 6 2 1 6 4 12035 Track 600#10 Foot Section 3 **330 Track 800#6 Foot Section 4 2 1 4 4 18 Foot Section 5 2 1 5 4 110 Foot Section 6 2 1 6 4 1376 Track 1000#6 Foot Section 4 2 1 4 4 18 Foot Section 5 2 1 5 4 110 Foot Section 6 2 1 6 4 1888 Track 2500#6 Foot Section 3 2 18 Foot Section 3 2 110 Foot Section 3 2 1888 Track 5000#6 Foot Section 4 2 ***8 Foot Section 5 2 ***10 Foot Section 6 2 ***
Track End Lock Cross End LockSeries Capacity Center Blind Joint* Ear Blind Joint
◗ Overhead Mounting31 Track 400#6 Foot Section 4 2 1 4 2 18 Foot Section 5 2 1 5 2 110 Foot Section 6 2 1 6 2 112 Foot Section 7 2 1 7 2 120 Foot Section 11 2 1 11 2 1232 Track 600#6 Foot Section 4 2 1 4 2 18 Foot Section 5 2 1 5 2 110 Foot Section 6 2 1 6 2 12035 Track 600#10 Foot Section 3 **330 Track 800#6 Foot Section 4 2 18 Foot Section 5 2 110 Foot Section 6 2 1376 Track 1000#6 Foot Section 4 2 18 Foot Section 5 2 110 Foot Section 6 2 1888 Track 2500#6 Foot Section 3 2 18 Foot Section 3 2 110 Foot Section 3 2 1888 Track 5000#6 Foot Section 4 2 ***8 Foot Section 5 2 ***10 Foot Section 6 2 ***
* Lock Joints used only when sectionsare coupled together in place of onecenter bracket
** No End Blinds are used—field installbolts through end of run
*** Lock Joints are not permitted, all cou-pled sections must be welded togetherusing jig kit
DOOR TRUCK / APRON ASSEMBLY DATA
7
◗ Number 31 Track0031.00115 Track 6'-0" Painted0031.00116 Track 8'-0" Painted0031.00117 Track 10'-0" Painted0031.00118 Track 12'-0" Painted0031.00119 Track 20'-0" Painted0031.00120 Track 6'-0" Galvanized0031.00121 Track 8'-0" Galvanized0031.00122 Track 10'-0" Galvanized0031.00123 Track 12'-0" Galvanized0031.00124 Track 20'-0" Galvanized
◗ 3130.00001 Medium-Duty Utility HangerDesigned for light to medium-duty, manually operated curtains. Typical applica-tions: stage curtains, machinery enclosure curtains, sound reducing curtains,etc. Hanger wheels are made of Delrin with a Delrin bearing surface to ensure asmoothly operating curtain. Hanger frames are made of steel with a zinc-platedfinish and are equipped with bumpers to prevent the hanger wheels from mak-ing contact with each other. Hangers should be spaced on 12" to 14" centersdepending on the weight of the curtains. Capacity is 25 lbs.–75 lbs. maximum.
Finish: Zinc-plated finish frame.
LOCK-JOINT ®BOX TYPE TRACK• N
umber 31 Track, 400 lb. Capacity per Pair or Trucks
7
NO. 31 TRACK, CROSS SECTION
◗ 3140.00001 Light-Duty Utility HangerDesigned for light to medium-duty, manually operated curtains. Typical applica-tions: stage curtains, machinery enclosure curtains, sound reducing curtains,etc. Hanger wheels are made of Delrin with a Delrin bearing surface to ensure asmoothly operating curtain. Hanger frames are made of steel with a zinc-platedfinish. Hangers should be spaced on 12" to 14" centers depending on the weight ofthe curtains. Capacity is up to 25 lbs. maximum.
Finish: Zinc-plated finish frame.
Center0031.00061 Painted
0031.00062 Galvanized
Lock-Joint0031.00063 Painted
0031.00065 Galvanized
End Blind0031.00050 Galvanized
◗ Sidewall Mounting
◗ Overhead Mounting
LOCK
-JOIN
T®BR
ACKE
TS FO
R NUM
BER 3
1 TRA
CK
8
Note: Maximum Bracket spacing is30" on centers. Tracks extend intoCenter and End Brackets 2".Use end blind in combination withany center bracket to produce anend bracket.
Center0031.00044 Painted
0031.00047 Galvanized
Lock-Joint0031.00051 Painted
0031.00054 Galvanized
Center Stop0031.00056 Painted
0031.00059 Galvanized
End Blind0031.00050 Galvanized
Double Center0031.00069 Painted
0031.00072 Galvanized
Double Lock-Joint0031.00075 Painted
0031.00076 Galvanized
Cross Ear Center0031.00085 Painted
0031.00087 Galvanized
Cross Ear Lock-Joint0031.00089 Painted
0031.00090 Galvanized
DOOR TRUCK / APRON ASSEMBLY DATA
7
◗ Door Top PlateNO. 3110.00012 DOOR TOP PLATE
Application: For wood doors 1w" minimum thickness -to be used instead of an apron.
Construction: Steel Plate.
Finish: Painted.
LOCK-JOINT ®DOOR HANGER/APRON ASSEMBLIES• N
umber 31 Track, 400 lb. Capacity
9
3120 HANGER/TRUCK ASSEMBLY WITH DELRIN® WHEELS
Use: For manually operated sliding doors 12" to 24" thick weighing up to 400 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 14", maximum 2w". Bottom of track to center of hole in sidewall bracket; 3w".
Construction: 28" diameter Delrin® wheels. Lateral and vertical adjustment.
Apron: 8" thick x 32" wide x 6" long.
Finish: Zinc plated.
3120.00001 Trucks, Less Aprons3120.00002 Hangers, for Doors 12" to 24" thick
3110 HANGER/TRUCK ASSEMBLY
Use: For manually operated sliding doors 12" to 24" thick weighing up to 400 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 14", maximum 22". Bottom of track to center of hole in sidewall bracket; 3w".
Construction: 28" diameter steel wheels. Lateral and vertical adjustment.
Apron: 8" thick x 32" wide x 6" long.
Finish: Zinc plated.
3110.00001 Trucks, Less Aprons3110.00002 Hangers, for Doors 12" to 24" thick
Drilled and Tappedfor 1/2-13 Threads
Drilled and Countersunkfor #12 F.H. Screw
1-1/2"
4-7/8"
3/8"
Hanger Assembly Shown
Hanger Assembly Shown
Num
ber
232
Trac
k, 6
00 lb
. Cap
acity
per
Pai
r of
Tru
cks
• LO
CK-J
OINT®
BOX T
YPE T
RACK
10
◗ Number 232 Track Straight0232.00064 Track 6'-0" Painted0232.00065 Track 8'-0" Painted0232.00066 Track 10'-0" Painted0232.00067 Track 6'-0" Galvanized0232.00068 Track 8'-0" Galvanized0232.00069 Track 10'-0" Galvanized
NO. 232 TRACK, CROSS SECTION
DOOR TRUCK / APRON ASSEMBLY DATA
7
LOCK-JOINT ®BRACKETS FOR NUMBER 232 TRACK
11
Center0232.00018 Painted
0232.00019 Galvanized
Lock-Joint0232.00020 Painted
0232.00022 Galvanized
End Blind0232.00007 Galvanized
◗ Sidewall Mounting
◗ Overhead Mounting
Note: Maximum Bracket spacing is24" on centers. Tracks extend intoCenter and End Brackets 2w".Use end blind in combination withany center bracket to produce anend bracket.
Center0232.00121 Painted
0232.00121ZC Zinc Plated
Lock-Joint0232.00122 Painted
0232.00122ZC Zinc Plated
Center Stop0232.00123 Painted
End Blind0232.00007 Galvanized
Double Center0232.00026 Painted
Double Lock-Joint0232.00032 Painted
Cross Ear Center0232.00044 Painted
0232.00046 Galvanized
Cross Ear Lock-Joint0232.00048 Painted
0232.00049 Galvanized
2320 HANGER/TRUCK ASSEMBLYCaged Roller Bearings
Use: For manually operated sliding doors 1w" to 2w" thick weighing up to600 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 54".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 74" long.
Finish: Zinc plated trucks/apron plated or painted.
2320.00001 – Trucks, Less Apron2320.00002 – Hanger, for doors 1w" to 24" Thick - Painted apron2320.00003 – Hanger, for doors 1w" to 24" Thick - Zinc apron2320.00004 – Hanger, for doors 24" to 2w" Thick - Painted apron2320.00005 – Hanger, for doors 24 to 2w" Thick - Zinc apron
2321 HANGER/TRUCK ASSEMBLYBall-Bearing
Use: For manually operated sliding doors 1w" to 2w" thick weighing up to 600 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 54".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 74" long.
Finish: Zinc plated trucks/apron plated or painted.
2321.00001 – Trucks, Less Apron2321.00002 – Hanger, for doors 1w" to 24" Thick - Painted apron2321.00003 – Hanger, for doors 1w" to 24" Thick - Zinc apron2321.00004 – Hanger, for doors 24" to 2w" Thick - Painted apron2321.00005 – Hanger, for doors 24 to 2w" Thick - Zinc apronN
umbe
r 23
2 Tr
ack,
600
lb. C
apac
ity p
er P
air
of T
ruck
s•
LOCK
-JOIN
T®DO
OR HA
NGER
/TRUC
K ASS
EMBL
IES
12
Hanger Assembly Shown
Hanger Assembly Shown
TUFF-TRACK™
• Num
ber 2035 Track, 600 lb. Capacity per Pair of Trucks
13
◗ Number 2035.00471 TrackSize: 10' lengths
Construction: x" steel
Finish: Painted
035 00
2-5/16”
1-3/4”
3/16”
2-11/16”
5/8”
NO. 2035 TRACK, CROSS SECTION
◗ 2035 Tuff-Track Hanger, Truck and Utility Hanger2035.01975 Hanger Assembly - Ball BearingUse: For doors that must negotiate horizontal track curves.Construction: 28" diameter machined steel wheels and b" diameter lateral thrustguide rollers. Pendent is s" diameter with 11 N.C. threads. Apron - 9/64" thick x 4"wide x 72" tall. Top Plate - 1w" wide x 7z" long.
Finish: Zinc plated trucks/painted apron.
2035.01976 Truck - Ball BearingUse: For loads up to 300 lbs. per truck (600 lbs. per pair)Construction: 28" diameter machined steel wheels and b" diameter lateral thrustguide rollers. Pendent is s" diameter with 11 N.C. threads.
Finish: Zinc plated.
3130.00001 Utility HangerDesigned for use with manually operated curtains. Typical applications; stage curtains, machinery enclo-sure curtains, sound reducing curtains, etc. Hanger wheels are made of Delrin and areequipped with Delrin bearings to insure a smoothly operating curtain. Hanger framesare made of steel, bumpers prevent the hanger wheels from running together.Hangers will operate in a curved section of track when it is necessary to run curtainaround a corner. Finish: zinc plated frame. Trucks should be spaced 12" to 14" cen-ters depending upon the weight of the curtains. Capacity is 25 lbs. – 75 lbs. maxi-mum.
Finish: Zinc plated frame.
HangerAssemblyShown
TruckAssemblyShown
Num
ber
2035
Tra
ck, 6
00 lb
. Cap
acity
per
Pai
r of
Tru
cks
• TUF
F-TRA
CK
14
◗ Welding Jig and BracketsTrack sections are connected together in two ways: By welding, using the 2035.00155 Welding Jig, or byusing the 2035.00021 wedge type joint bracket.
Welding Jig 2035.00155The welding method is recommended since it eliminates the necessity for thejoint brackets and makes a continuous section of track. The welding jig alignsthe inside of the track, holds the two sections in position for welding, andkeeps the weld bead flush with the track to insure smooth operation.
Finish: Brass.
Overhead Track Bracket 2035.01912The 2035.01912 bracket is used only for suspending the track bymeans of a single bolt. The bracket should be used for supporting thetrack when the joints are welded and should be used on curves,except when the track is supported by angles or flat bars. Distancefrom top of bracket to bottom of track is 3w”.
Finish: Painted.
Overhead Joint Bracket 2035.00021This bracket holds the sections of track to be joined in perfect align-ment. The wedges are drawn together using the bolts through thesides of the bracket. When the wedges are tightened they securelyclamp the sections of track. Distance from top of bracket to bottomof track is 3w”.
Finish: Painted.
◗ No. 235 Tuff-Track Brackets2035.01912 Standard BracketMaximum Spacing 60" O.C.Weight: 2 lbs.
2035.00021 Joint BracketWeight: 3 lbs.
2035.01982 Bracket Angle PackageUse with a supplied 2" fastener for Sidewall ApplicationsWeight: 3 lbs.
◗ Radius @ 90° ◗ Part Number1' 6" 2035.013281' 6" (H) 2035.020642' 0" 2035.013312' 0" (H) 2035.013522' 3" 2035.013352' 3" (H) 2035.013542' 6" 2035.01833.142' 6" (H) 2035.01830.112' 9" 2035.01833.152' 9" (H) 2035.01830.123' 0" 2035.013383' 0" (H) 2035.01830.133' 3" 2035.013413' 6" 2035.01833.183' 9" 2035.01833.194' 0" 2035.013444' 3" 2035.013474' 6" 2035.01833.224' 9" 2035.01833.235' 0" 2035.01833.245' 3" 2035.01833.255' 6" 2035.01833.265' 9" 2035.01833.276' 0" ** 2035.01836.286' 3" ** 2035.01836.296' 6" ** 2035.01836.306' 9" ** 2035.01836.317' 0" ** 2035.01836.327' 3" ** 2035.01836.337' 6" ** 2035.01836.347' 9" ** 2035.01836.358' 0" ** 2035.01836.368' 3" ** 2035.01836.37
** Note: Curve up to 5' 9" furnished in 90°.Curves 6' 0" to 11' 9" furnished in 45°.
(H) = Hardened Component
TUFF-TRACK HORIZONTAL CURVES
15
◗ Radius @ 45° ◗ Part Number8' 4" 2035.01836.528' 6" 2035.01836.388' 9" 2035.01836.399' 0" 2035.01836.409' 3" 2035.01836.419' 6" 2035.01836.429' 9" 2035.01836.4310' 0" 2035.01836.4410' 3" 2035.01836.4510' 6" 2035.01836.4610' 9" 2035.01836.4711' 0" 2035.01836.4811' 3" 2035.01836.4911' 6" 2035.01836.5011' 9" 2035.01836.51
Finish: Painted
Contact Customer Service for larger radius requirements.
Num
ber
330
Trac
k, 8
00 lb
. Cap
acity
per
Pai
r of
Tru
cks
• LO
CK-J
OINT®
BOX T
YPE T
RACK
16
NO. 330 TRACK, CROSS SECTION
◗ Number 330 Track0330.00001 Track 6'-0" Painted0330.00002 Track 8'-0" Painted0330.00003 Track 10'-0" Painted
DOOR TRUCK / APRON ASSEMBLY DATA
7
LOCK-JOINT ®BRACKETS FOR NUMBER 330 TRACK
17
Center0330.00062 Painted
Lock-Joint0330.00064 Painted
End Blind0330.00051 Galvanized
◗ Sidewall Mounting
◗ Overhead Mounting
Note: Maximum Bracket spacing is 24" on centers. Tracks extend into Center and End Brackets 3".Use end blind in combination with any center bracket to produce an end bracket.
Center0330.00132 Painted
Lock-Joint0330.00133 Painted
Center Stop0330.00134 Painted
End Blind0330.00051 Galvanized
Double Center0330.00070 Painted
Double Lock-Joint0330.00076 Painted
3300 HANGER/TRUCK ASSEMBLYCaged Roller Bearings
Use: For manually operated sliding doors 1w" to 3" thick weighing up to 800 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 52".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
3300.00001 – Trucks, Less Apron3300.00002 – Hanger, for Doors 1w" to 24" Thick3300.00004 – Hanger, for Doors 24" to 3" Thick
3301 HANGER/TRUCK ASSEMBLYBall Bearing
Use: For manually operated sliding doors 1w" to 3" thick weighing up to 800 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 52".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
3301.00001 – Trucks, Less Apron3301.00002 – Hanger, for Doors 1w" to 24" Thick3301.00004 – Hanger, for Doors 24" to 3" Thick
Num
ber
330
Trac
k, 8
00 lb
. Cap
acity
per
Pai
r of
Tru
cks
• LO
CK-J
OINT®
DOOR
HANG
ER/TR
UCK A
SSEM
BLIES
18
Hanger Assembly Shown
Hanger Assembly Shown
DOOR TRUCK / APRON ASSEMBLY DATALOCK-JOINT ®
BOX TYPE TRACK• Num
ber 376 Track, 1000 lb. Capacity per Pair or Trucks
19
NO. 376 TRACK, CROSS SECTION
◗ Number 376 Track0376.00002 Track 6'-0" Painted0376.00004 Track 8'-0" Painted0376.00006 Track 10'-0" Painted
Center0376.00080 Painted
Lock-Joint0376.00088 Painted
End Blind0376.00015 Galvanized
◗ Sidewall Mounting
◗ Overhead Mounting
LOCK
-JOIN
T®BR
ACKE
TS FO
R NUM
BER 3
76 TR
ACK
20
Note: Maximum Bracket spacing is 24" on centers. Tracks extend into Center and End Brackets 3".Use end blind in combination with any center bracket to produce an end bracket.
Center0376.00089 Painted
Lock-Joint0376.00090 Painted
Center Stop0376.00091 Painted
End Blind0376.00015 Galvanized
Double Center0376.00092 Painted
Double Lock-Joint0376.00093 Painted
DOOR TRUCK / APRON ASSEMBLY DATA
7
LOCK-JOINT ®DOOR HANGER/TRUCK ASSEMBLIES• N
umber 376 Track, 1000 lb. Capacity per Pair of Trucks
21
3300 HANGER/TRUCK ASSEMBLYCaged Roller Bearings
Use: For manually operated sliding doors 1w" to 3" thick weighing up to 1000 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 6".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
3300.00001 – Trucks, Less Apron3300.00002 – Hanger, for Doors 1w" to 24" Thick3300.00004 – Hanger, for Doors 24" to 3" Thick
3301 HANGER/TRUCK ASSEMBLYBall Bearings
Use: For manually operated sliding doors 1w" to 3" thick weighing up to 1000 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 18", maximum 2w". Bottom of track to center of hole in sidewall bracket; 6".
Construction: 3" diameter steel wheels. Lateral and vertical adjustment. Apron:9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
3301.00001 – Trucks, Less Apron3301.00002 – Hanger, for Doors 1w" to 24" Thick3301.00004 – Hanger, for Doors 24" to 3" Thick
3761 HANGER/TRUCK ASSEMBLYBall Bearings
Use: For power operated sliding doors 1w" to 3" thick weighing up to 800 lbs.using No. 376 track.
Head Clearance: Distance top of door to bottom of track; minimum 1a", maximum 3". Bottom of track to center of hole in sidewall bracket; 6".
Construction: 2w" diameter machined steel wheels. Lateral and vertical adjust-ment. Apron: 9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
3761.00001 – Trucks, Less Apron3761.00002 – Hanger, for Doors 1w" to 24" Thick3761.00004 – Hanger, for Doors 24" to 3" Thick
Hanger Assembly Shown
Hanger Assembly Shown
Hanger Assembly Shown
Num
ber
888
Trac
k, 5
000
lb. C
apac
ity p
er P
air
of T
ruck
s•
LOCK
-JOIN
T®BO
X TYP
E TRA
CK
22
NO. 888 TRACK, CROSS SECTION
◗ Weld / Lube KitUse: Fixture to hold #888 track ends in alignment whenfield welded joint is required. Grease to be applied totrack runways for smooth operation. Reusable for up to30-50 weld operations, depending on temperatureusage.
Construction: Brass or bronze fixture clamp parts, steelbolt, white grease.
Packed: Boxed with instruction sheet.
FIELD WELD TRACK JOINTS USING 888 WELDING JIG
GREASE TRACK RUNWAY BARSUSING 888 GREASE
TACK WELD BOTH SIDES, THENREMOVE "C" CLAMPAND WELDAROUND OUTSIDE OF TRACK
"C" CLAMP (NOT BY RICHARDS-WILCOX)
◗ Number 888 Track0888.00329 Track 6'-0" Painted0888.00330 Track 8'-0" Painted0888.00331 Track 10'-0" Painted
DOOR TRUCK / APRON ASSEMBLY DATA
7
LOCK-JOINT ®BRACKETS FOR NUMBER 888 TRACK
23
Center0888.00381 Painted
Lock-Joint0888.00387 Painted
End Blind0888.00388 Galvanized
◗ Sidewall Mounting
◗ Overhead Mounting
Note: Maximum spacing between brackets is 60" on center for 2500 lb. capacity and 24" on center for 5000 lb. capacity.Tracks extend into center and end brackets 42"Use end blind in combination with any center bracket to produce an end bracket.†888 track joints must be welded on 2500 and 5000 lb. applications. See page 24 for welding kit information.
Center0888.00383 Painted
Lock-Joint0888.00386 Painted
End Blind0888.00388 Galvanized
8880 HANGER/TRUCK ASSEMBLYBall Bearings
Use: For manually operated or power operated sliding doors 1w" to 3" thickweighing up to 1500 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 1a", maximum 2w". Bottom of track to center of hole in sidewall bracket; 6w".
Construction: 3" diameter machined steel wheels. Frame, malleable iron, lateral and vertical adjustment. Apron: 9/64" thick x 4" wide x 72" long.
Finish: Zinc plated trucks/painted apron.
8880.00001 – Truck, Less Apron8880.00002 – Hanger, for Doors 1w" to 24" Thick8880.00004 – Hanger, for Doors 24" to 3" Thick
8881 HANGER/TRUCK ASSEMBLYBall Bearings
Use: For manually operated or power operated sliding doors 24" to 34" thickweighing up to 2500 lbs.
Head Clearance: Distance top of door to bottom of track; minimum 42", maximum 62". Bottom of track to center of hole in sidewall bracket; 6w".
Construction: 3" diameter machined steel wheels. Frame, malleable iron, lateral and vertical adjustment. Apron: 4" thick x 5" wide x 11w" long.
Finish: Zinc plated trucks/painted apron.
8881.00001 – Truck, Less Apron8881.00002 – Hanger, for Doors 24" to 3w" Thick
Num
ber
888
Trac
k, 1
500/
2500
lb. C
apac
ity p
er P
air
of T
ruck
s•
LOCK
-JOIN
T®DO
OR HA
NGER
/TRUC
K ASS
EMBL
IES
24
Hanger Assembly Shown
Hanger Assembly Shown
DOOR TRUCK / APRON ASSEMBLY DATA
7
LOCK-JOINT ®DOOR TRUCK ASSEMBLIES• N
umber 888 Track, 2500/5000 lb. Capacity per Pair of Trucks
25
8881 TRUCK ASSEMBLYBall Bearings
Use: For manually operated or power operated sliding doors weighingup to 5000 lbs.
Head Clearance: Distance top of door to bottom of track; minimum78", maximum 108". Bottom of track to center of hole in sidewallbracket; 6w".
Construction: 3" diameter machined steel wheels. Frame, malleableiron, and vertical adjustment. Load Bar: 14" x 3" x 11" long steel.Pendant Bolt: 1" diameter steel.
Finish: Zinc plated trucks/painted load bar.
8881.00017 Tandem Truck
8881 TRUCK ASSEMBLYAnti Kickup – Ball Bearings
Use: For manually operated or power operated sliding doors weighingup to 2500 lbs. Larger wheels and guides prevent kickup.
Construction: 3" diameter machined steel wheels, Delrin guides.Frame, malleable iron, ball bearings, lateral and vertical adjustment.Pendant Bolt: d" diameter steel.
Finish: Zinc plated trucks
8881.00018 Truck
Tandem Truck Assembly Shown
Truck Assembly Shown
304
Gra
de S
tand
ard
• STA
INLES
S STEE
L HAR
DWAR
E
26
◗ Stainless Steel Door Hanger/Truck AssembliesPart Pound Capacity DescriptionNumber Per Pair
3110.00001SS 400 Truck –Roller Bearings3110.00006SS 400 Hanger, for Doors 12 to 24" Thick2320.00001SS 600 Truck – Roller Bearings2320.00006SS 600 Hanger, for Doors 1w" to 24" Thick2320.00008SS 600 Hanger, for Doors 24" to 2w" Thick
◗ Stainless Steel TrackTrack Track LengthNo. 6' 8' 10'
31 0031.00115SS 0031.00116SS 0031.00117SS232 0232.00064SS 0232.00065SS 0232.00066SS
Truck Assembly Shown
Hanger Assembly Shown
◗ Stainless Steel AccessoriesBow Handle0083.00002SS
Flush Pull0072.00001SS
Binder0082.00007SS
Stay Roller0058.00002SS
No. 232600 LB. CAPACITY
No. 31400 LB. CAPACITY
1-3/4"
2-1/4"
2-7/32"
3-1/4"
14 GA
16 GA
DOOR TRUCK / APRON ASSEMBLY DATA
7
STAINLESS STEEL LOCK-JOINT ®BRACKETS FOR NUMBER 31 AND NUMBER 232 TRACK SERIES
27
Center0031.00061SS0232.00018SS
Lock-Joint0031.00063SS0232.00020SS
End Blind0031.00050SS0232.00007SS
◗ Sidewall Mounting
◗ Overhead Mounting
Center0031.00044SS0232.00121SS
Lock-Joint0031.00051SS0232.00122SS
End Blind0031.00050SS0232.00007SS
Cross Ear Center0031.00085SS0232.00044SS
Cross Ear Lock-Joint0031.00089SS0232.00048SS
The industry has been using the Flat Track/Hanger concept since the early1900’s for a variety of applications.
◗ No. 102 Flat Track Hanger AssemblyUse: On Richards-Wilcox flat steel bar track which projects a minimum 1,"(face of wall to centerline of wheel) for manually operated doors 1s" to 22"thick weighing up to 800 lbs.
Two Styles: 0102.00075 for doors up to 1s" thick.0102.00076 for doors up to 22" thick.
Head Clearance: From top of track to top of truck/hanger assembly, 5a".
Construction: Wheels 4" tread diameter-gray iron; roller bearings, apron-a" x32" x 21" steel.
Finish: Painted.
FLAT T
RACK
HANG
ER AS
SEMB
LY
28
0102.00075
0102.00076
◗ Track0102.00046 Flat Track with Holes 6'-0" Long, Painted Finish0102.00048 Flat Track with Holes 8'-0" Long, Painted Finish0102.00050 Flat Track with Holes 10'-0" Long, Painted Finish0102.00055 Flat Track Bracket Spacer, Painted Finish0102.00087 End Stop/Bumper Assembly, Painted Finish
Note: Flat track bracket spacer required on 30" centers.
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
29
0054.00003 GUIDE ROLLERWheel, high impact nylon, 22" diameter. Covered with steel frame,6" long x 2w" high x 2" wide.
Finish: Zinc plated.
No fasteners included.
0058.00002 GUIDE ROLLERFor doors 12" to 2w" thick. Adjustable and reversible. Wheel, highimpact nylon, 22" diameter. Steel frame, 42" long x 22" high x 14"wide.
Finish: Painted.
No fasteners included.
0059.00007 GUIDE ROLLER (With Back Brace)Extra high to suit door on incline track. Wheel, gray iron, 3" diameter.Steel frame, 22" wide x x" thick. Distance from floor to center of wheel,8a". Overall height, 92".
Finish: Painted.
No fasteners included.
0153.00005 GUIDE ROLLERAdjustable and reversible for inside or outside doors 14" to 3"thick. Wheel, gray iron, 3" diameter.Construction: Steel frame.
Finish: Painted.
No fasteners included.
0154.00004 GUIDE ROLLERWheel, gray iron, 3" diameter. Heavy steel frame with slotted screwholes provides means for adjustment. 7" long x 3" high x 5" wide.Construction: Steel Frame.
Finish: Painted.
No fasteners included.
◗ Door Pulls0070.00005 FLUSH DOOR PULL (Standard Duty)For doors up to 1w" thick. Requires d"deep mortise.
Size: 4" x 6"
Finish: Steel/painted.
Inside dimension of cup 1v" wide x 32" high x d" deep
0070.00006 FLUSH DOOR PULL (Standard Duty)For doors over 1w" thick. Requires 1n" deep mortise.
Finish: Steel/painted.
Fasteners included.
0470.00001 FLUSH PULL (Heavy Duty)For very heavy doors 1w" or more in thickness. Requires 1w" deep mortise.
Finish: Malleable iron/painted.
No fasteners included.
0535.00489 FLUSH PULL – Black Painted Finish (Light Duty)0535.00615 FLUSH PULL – Brushed Aluminum Finish (Light Duty)Designed for use with any door 1a" or more in thickness. Requires d" deep mortise.
Fasteners included.
0072.00002 FLUSH PULL – SteelDesigned for use with any door 1a" or more in thickness.
Finish: US26D chrome.
Fasteners included.
DOOR
HARD
WARE
30
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
31
◗ Bow Handles0071.00001 BOW HANDLE (62" long)0071.00002 BOW HANDLE (7a" long)Steel construction.
Finish: Painted.
Bolt holes register with Model 70 flush pulls.
No fasteners included.
0081.00001 BOW HANDLE (6a" long)0081.00002 BOW HANDLE (8" long)
Constructed of malleable iron.
Finish: Painted.
Fasteners included.
0191.00001 BOW HANDLE
Constructed of malleable iron.
Size: 15" long.
Finish: Painted.
No fasteners included.
◗ Heavy Hasp0182.00020ZC HEAVY HASP (up to 1w" thick doors)0182.00032ZC HEAVY HASP (up to 3" thick doors)
For use with heavy doors as a combination doorbumper, binder, and hasp. Construction: Hasp, mal-leable iron/staple, steel. Length, main body, on wall,7d". Length of hinged overleaf 5".
Finish: Zinc Plated.
Fasteners included.
◗ Floor Guide and Track0739.00026 FLOOR GUIDEFor use on wood doors 1a" and over. Number of guides shouldequal number of truck/hanger assemblies used on doors.Should be located directly in line with truck/hanger assemblies onsliding doors. Rollers held in contact with the guide track by light spring pressure;swivels when used with folding doors.
Finish: Painted.
Fasteners included.
0739.00028 FLOOR GUIDE TRACKDesigned for use with the 0739.00026 Floor Guide on single sliding orfolding wood door applications. Available in single track sets 10'-0". Use multiple sets for parallel slidingdoors.
Construction: Heavy steel bars, a" x 2" x 10'-0".
Finished: Painted.
No fasteners included.
DOOR
HARD
WARE
32
◗ Guide Roller StripsMounts directly to face of door. When door moves stay rolleroperates against strip instead of causing wear to door.
Construction: Steel 8" x 12". Countersunk holes for #10 flat headscrews.
Finish: Painted.
No fasteners included
Part Number 0647.00238 0647.00250 0647.00274 0647.00298 0647.00322
Length 3' 4' 6' 8' 10'
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
33
◗ Binders/Stops0089.00004 ADJUSTABLE DOOR BINDER AND STOPFor doors 1w" to 3" thick. Three-piece steel construction, base x"thick, brace 8" thick by 1w" wide. End is flared to receive door.May be used at front or back of door.
Finish: Painted.
Fasteners included.
BUMPER SHOE0102.00136 (Painted)0102.00137 (Galvanized)32" high x 32" wide x w" deep. To protect the corners of wood doors wherethey come in contact with binders, bumpers, and guides. 16 gauge steel.
Fasteners included.
0572.00001 END STOP (Shown with Bumper Shoe)For straight sliding doors, any thickness.Height, 24". Door receiving space: 2" x 2". Malleable iron.Reversible for right- or left-hand. Adjustable to and from wall.
Finish: Painted.
No fasteners included.
NOTE: Bottom of wood doors which comes into contact with guides shouldbe protected by steel bumper shoes which must be ordered separately.
STEEL BINDER - 82 SERIESSteel, 4" thick x 2" wide for three thicknesses of doors.
Finish: Painted.
No fasteners included.
STEEL BINDER - 102 SERIESSteel, a" thick x 3" wide for doors 1w" or 22" thick.
Finish: Painted.
No fasteners included.
Part No. 0082.00002 0082.00005 0082.00007 0102.00033 0102.00034
Thickness of Door 1w" 22" 3" 1w" 22"
82 Series
102 Series
◗ Floor Center Stop0171.00001 FLOOR CENTER STOP* (up to 24" door thickness)0171.00003 FLOOR CENTER STOP* (24" to 3" door thickness)Can be fastened to floor or imbedded in concrete.
Construction: Steel.
Finish: Painted.
No fasteners included.
*Note: Bottom of wood doors which comes in contact with guides should be protected by steel bumpershoes which must be ordered separately. See parts 0102.00136 or 0102.00137.
◗ Door Holder0119.00003 DOOR HOLDERFor wall attachment.
Construction: Spring Steel.
Finish: Painted.
Fasteners included.
◗ Door Guide Set0771.00003 DOOR GUIDE SET*For four-fold garage doors of any thickness. Two malleable iron pieces, one 18" wide, the other 10w"wide.On out opening doors place long piece on inside and shortpiece on outside of opening.
Finish: Painted.
No fasteners included.
*NOTE: Bottom of wood doors which comes in contact with guide should be protected by steel bumpershoes which must be ordered separately. See parts 0102.00136 and 0102.00137
DOOR
HARD
WARE
34
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
35
◗ Door Latches0125.00015 DOOR LATCH - Door opens from both sides.
Construction: Latch bar, steel. Lever handle, malleable iron.
Application: For large swing doors up to 3" thick. Operatelatch by turning lever handle on far side or lifting handle on near side. Latch bar c"x 12" x 13s" long. Reversible for left or right hand doors.
Finish: Zinc plated. Optional longer spindle for thicker doors.
No fasteners included.
0128.00010 OFFSET DOOR LATCH (Painted Latch Bar andKeeper Zinc Plated)0128.00012 OFFSET DOOR LATCH (Zinc Plated)
Construction: Latch bolt, malleable iron-2" x 8". Keeper andguides, steel.
Application: For medium sized swing or slide doors.Reversible for left or right hand doors. Offset latch ends preventaccidental opening by vibration.
Fasteners included.
0128.00011 OFFSET DOOR LATCH
Construction: Latch bolt, malleable iron-w" x 12". Keeperand guides, steel.
Application: For large sized swing or slide doors. Reversiblefor left or right hand doors. Offset latch ends prevent acci-dental opening by vibration.
Finish: Latch bar painted. Clips and keeper zinc plated.
Fasteners included.
0128.00014 LATCH PADLOCK STAPLE
Construction: Steel -1w" wide x 24" high x 14" projection.Application: To be used with Series 128 latches when padlock is required.
Finish: Zinc plated.
No fasteners included.
Door Latch
Offset Door Latch
Offset Door Latch
◗ Door Latches0152.00023 DOOR LATCH - Door opens from both sides.
Application: For large swing or slide doors from 1w" to 2w"thick. Operate latch by turning flush handle on far side or liftinghandle on near side. Reversible for left or right hand doors.Keeper has aligning holes for padlock. Latch bar size, c" x 12"x 13s" long. Flush cup size, 3" x 3d" high inside.
Construction: Steel.
Finish: Zinc plated. Optional longer spindle for thicker doors.
No fasteners included.
0225.00043 SMALL DOOR LATCH0225.00045 MEDIUM DOOR LATCHDoor opens from both sides.
Construction: Latch bar, steel. Handles, malleable iron.
Application: For small and medium sized swing doors from 1w"to 2s" thick. Operate latch bar from either side by turning han-dle. Reversible for left or right hand doors.
Finish: Zinc plated. Optional longer spindle for thicker doors.
No fasteners included.
Part Number Handle Type Latch Bar
0225.00043 Tee 4" x 1" x 10" Long0225.00045 Lever c" x 12" x 13s" Long
1025.00019 DOOR LATCH (Left Hand)1025.00026 DOOR LATCH (Right Hand)
Use: For small sized swing or slide doors.
Construction: Steel. Latch Bar: x" x 1" x 64" long.
Finish: Painted.
Fasteners included.
DOOR
HARD
WARE
36
Door Latch
0225.00043Small Door Latch
0225.00045Medium Door Latch
Left Hand Shown
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
37
◗ BoltsMEDIUM DUTY0434.00096 SPRING BOLT WITH 0434.00027 KEEPER0434.00096 SPRING BOLT WITH 0434.00248 KEEPERConstruction: Bolt and housing, malleable iron. Keeper, steel.
Application: For securing medium sized swing or slide-fold doors in theclosed position. Available with two types of keepers to meet most doorapplications. Includes 36" steel chain with ring and clip. Suitable for stopside mounting on wood, composite, or structural steel doors.Bolt size: 4w" wide x 6" long x 1d" projection. When ordering, specifykeeper desired.
Finish: Painted.
No fasteners included.
LIGHT DUTY0514.00036 SPRING BOLTApplication: For securing small sized swing or slide-fold doors in the closed position.Includes both keepers for hinge side or stop side mounting and 36" steel chain withring and clip. Bolt size: 32" wide x 9" long x 12" projection.
Construction: Steel.
Finish: Painted.
Fasteners included.
HEAVY DUTY0514.00038 SPRING BOLTApplication: For securing large sized swing or slide-fold doors in the closed position.Includes keeper for hinge side mounting, and 60" steel chain with ring and clip. Bolt size: 44" wide x 9" long x 1w" projection.
Construction: Bolt, housing, and keeper malleable iron.
Finish: Painted.
Fasteners included.
NOTE: No. 0434.00027 keeper can be used for stop side mounting. Furnished at additional charge.
HEAVY DUTYCANE BOTTOM BOLTSConstruction: Steel. Bolt drops by gravity when handle is lifted out of socket. Keeper installedin wood or concrete floor.
Application: For garage, warehouse, or swinging doors.
Finish: Zinc plated.
Fasteners included.
0434.00027KeeperShown
0434.00248KeeperShown
Part Number Dimensions Projection from Door
0524.00021 s" x 18" Long 1c"0524.00023 w" x 24" Long 1v"
◗ Heavy Duty Cremone BoltApplication: For securing medium sized swing or slide-fold doors at the top and bottom with the move-ment of one lever handle. Connection of the rods to the lever handle is made with offset arms. The topand bottom bolts can only be retracted by movement of the lever handle. Models with exterior lever han-dle are designed for doors 1w" to 4" thick.
Assembly is designed for openings up to 6'-8" to 23'-0" high. Lever handle located 48" from floor line,throw of bolt 3", projection from door 5s". Included are keepers to meet most applications.
Construction: Bolts, guides, and handles are malleable iron. Rods-w" diameter steel.
Finish: Zinc plated.
Ordering data: Specify cremone bolt assembly based on door height and thickness (for external handle).Specify options if required.
◗ Heavy Duty Cremone BoltsPart # Description Weight per Unit
1028.00310.008 Heavy Duty Cremone Bolt – Zinc Plated – 6'-8" to 8' Door Height 50.00 lb.1028.00310.009 Heavy Duty Cremone Bolt – Zinc Plated – 8' to 9'-6' Door Height 50.00 lb.1028.00310.011 Heavy Duty Cremone Bolt – Zinc Plated – 9'-6" to 11' Door Height 50.00 lb.1028.00310.012 Heavy Duty Cremone Bolt – Zinc Plated – 11' to 12'-6" Door Height 50.00 lb.1028.00310.014 Heavy Duty Cremone Bolt – Zinc Plated – 12'-6" to 14' Door Height 53.00 lb.1028.00310.015 Heavy Duty Cremone Bolt – Zinc Plated – 14' to 15'-6" Door Height 53.00 lb.1028.00310.017 Heavy Duty Cremone Bolt – Zinc Plated – 15'-6" to 17' Door Height 53.00 lb.1028.00310.018 Heavy Duty Cremone Bolt – Zinc Plated – 17' to 18'-6" Door Height 53.00 lb.1028.00310.020 Heavy Duty Cremone Bolt – Zinc Plated – 18'-6" to 20' Door Height 53.00 lb.1028.00310.021 Heavy Duty Cremone Bolt – Zinc Plated – 20' to 21'-6" Door Height 53.00 lb.1028.00310.023 Heavy Duty Cremone Bolt – Zinc Plated – 21'-6" to 23' Door Height 53.00 lb.
◗ Cremone Bolt AccessoriesPart # Description
1028.00330 Cremone Bolt Auxiliary Handle Package1028.00340 Cremone Bolt Key Lock/Knob Package with Auxiliary Handle Included1028.00350 Cremone Bolt Key Lock Both Sides Package with Auxiliary Handle Included1028.00360 Cremone Bolt Heavy Hasp Package1028.00370 Cremone Bolt 3' Add-On Package
DOOR
HARD
WARE
38
LockPackage
Heavy Hasp PackageIncludes OutsideHandle and PadlockStaple.
Note: See Architectural Binder or CD for Full Size CAD Drawings.
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
39
◗ Heavy Duty Cremone Bolt
◗ Extra Heavy Duty Cremone BoltApplication: For securing large sized industrial swing or slide-fold doors at the top and bottom with themovement of one lever handle. Connection of the rods to the lever handle is made with offset arms. Thetop and bottom bolts can only be retracted by movement of the lever handle. Models with exterior han-dle are designed for doors 1w" to 4" thick.
Regular assembly is designed for openings up to 6'-8" to 23'-0" high. Lever handle located 48" from floorline, throw of bolt 3", projection from door 5s". Included are keepers to meet most applications.
Construction: Bolts, guides, and handles, are malleable iron. Rods-w" diameter steel.
Finish: Zinc plated.
Ordering data: Specify cremone bolt assembly based on door height and thickness (for external handle).Specify options if required.
◗ Extra Heavy Duty Cremone BoltsPart # Description Weight per Unit
1028.00320.009 Extra Heavy Duty Cremone Bolt – Zinc Plated – 8'-0" to 9'-0" Door Height 75.00 lb.1028.00320.010 Extra Heavy Duty Cremone Bolt – Zinc Plated – 9'-0" to 10'-0" Door Height 75.00 lb.1028.00320.012 Extra Heavy Duty Cremone Bolt – Zinc Plated – 10'-0" to 12'-6" Door Height 75.00 lb.1028.00320.014 Extra Heavy Duty Cremone Bolt – Zinc Plated – 12'-6" to 14'-6" Door Height 78.00 lb.1028.00320.017 Extra Heavy Duty Cremone Bolt – Zinc Plated – 14'-6" to 17'-6" Door Height 78.00 lb.1028.00320.020 Extra Heavy Duty Cremone Bolt – Zinc Plated – 17'-6" to 20'-6" Door Height 81.00 lb.1028.00320.023 Extra Heavy Duty Cremone Bolt – Zinc Plated – 20'-6" to 23'-6" Door Height 81.00 lb.
◗ Cremone Bolt AccessoriesPart # Description
1028.00330 Cremone Bolt Auxiliary Handle Package1028.00340 Cremone Bolt Key Lock/Knob Package with Auxiliary Handle Included1028.00350 Cremone Bolt Key Lock Both Sides Package with Auxiliary Handle Included1028.00360 Cremone Bolt Heavy Hasp Package1028.00370 Cremone Bolt 3' Add-On Package
DOOR
HARD
WARE
40
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR HARDWARE
41
LockPackage
Heavy Hasp PackageIncludes OutsideHandle and PadlockStaple.
Note: See Architectural Binder or CD for Full Size CAD Drawings.
◗ Extra Heavy Duty Cremone Bolt
◗ Bi-Parting Sliding Door Hardware SetsSIN
GLE A
ND BI
-PAR
TING S
LIDING
DOOR
HARD
WARE
SETS
42
End StopsSet end stops into concrete 3/4" when used with concrete floor.
Floor LineStay Rollers
Binders may be used in place of end stops.
Center Bracket
Center Bracket with End Blind.
Edge of door when open.
2'-0" Ctrs.5'-0" Ctrs.
for 888track Joint Bracket
Truck/ApronAssembly
Bow Handle Flush Pull(opposite side)
Bumper Shoes
Guide Roller Strip
Floor Center Stop
Center Stop Bracket(Except 888 Track)
End StopsSet end stops into concrete 3/4" when used with concrete floor.
Floor Line
Stay Roller
Binders may be used in place of end stops.
Center BracketCenter Bracket with EndBlind.
Edge of door when open.
2'-0" Ctrs.5'-0" Ctrs.
for 888track
Joint Bracket
Truck/ApronAssembly
Bow Handle
Flush Pull(opposite side)
Bumper Shoes
Guide Roller Strip
◗ Single Sliding Door Hardware Sets
Standard Head SectionUsing Brackets
Standard Head SectionUsing Brackets
Overhead Head Section
Overhead Head Section
HARDWARE SETS• For Wood and M
etal Doors
43
◗ Single and Bi-Parting DataBolt Hole
Distance CentersBottom of Center of on
For Kit Distance from Track to Bracket Diameter Crt. StopDoors Thickness Number Top of Door to Center of Bolt Hole of Bracket
Weighing of Single Bi-Parting Track Hanger Bottom of Track Bracket to Top Bracket (Bi-PartingPounds Door Door Door Number Number Min. Max. Bolt Hole of Bracket Bolt only)
◗ Manual Doors400 12" to 24" 1610 2610 31 3110.00002 14" 22" 3w" m" a" 2a"
600 1w" to 24" 1620 2620 232 2320.00002 18" 2w" 54" d" s" 38"600 1w" to 24" 1621 2621 232 2321.00002 18" 2w" 54" d" s" 38"600 24" to 2w" 1622 2622 232 2320.00004 18" 2w" 54" d" s" 38"600 24" to 2w" 1623 2623 232 2321.00004 18" 2w" 54" d" s" 38"
800 1w" to 24" 1630 2630 330 3300.00002 18" 2w" 52" 1" 2" 3a"800 1w" to 24" 1631 2631 330 3301.00002 18" 2w" 52" 1" 2" 3a"800 24" to 3" 1632 2632 330 3300.00004 18" 2w" 52" 1" 2" 3a"800 24" to 3" 1633 2633 330 3301.00004 18" 2w" 52" 1" 2" 3a"
1000 1w" to 24" 1640 2640 376 3300.00002 18" 2w" 6" 1" s" 3a"1000 24" to 3" 1642 2642 376 3300.00004 18" 2w" 6" 1" s" 3a"1000 1w" to 24" 1645 2645 376 3301.00002 18" 2w" 6" 1" s" 3a"1000 24" to 3" 1649 2649 376 3301.00004 18" 2w" 6" 1" s" 3a"
◗ Power or Manual Doors800 1w" to 24" 1641 2461 376 3761.00002 1a" 3" 6" 1" s" 3a"800 24" to 3" 1643 2463 376 3761.00004 1a" 3" 6" 1" s" 3a"
1500 1w" to 22" 1650 2650 888 8880.00002 1a" 2w" 6w" 1" w" —1500 24" to 3" 1652 2652 888 8880.00004 1a" 2w" 6w" 1" w" —
2500 24" to 3w" 1651 2651 888 8881.00002 42" 62" 6w" 1" w" —5000 per application 888 8881.00017
Note #1: Please specify door opening when pricing and ordering.
Note #2: 888 Track joints must be welded on all manual 2500 to 5000 lb. applications and all powered applications.
Note #3: Hardware sets listed for power operations can also be used with manually operated doors.
No. 434 Slide-Fold Hardware Sets are to used on large manually operated and power operated door appli-cations which require the door panels to slide-fold to each jamb leaving a clear opening. The 434 slide-fold hardware is available in two sizes for maximum 18'-0" wide openings and total door weights up to5,000 lbs.
Catalog Number Maximum Total Weight for a Set of 4 Doors
434x376 Hardware Up to 2,000 Lbs434x888 Hardware 2,000 Up to 5,000 Lbs.
Hardware sets consists of: Truck/Hanger assemblies, tracks, brackets, jamb hinges, center hinges, backplates, bow handles, center floor guide, top bolts, and cane bolts.
Disc bearing hinges are recommended for manually operated doors.
Ball bearing hinges should be used on all power operated doors and any manually operated doors whichwill have a high frequency of use.NOTE: Top bolts and cane bolts are used on manually operated sets only.
◗ Optional Equipment (Extra Cost)Weatherstrip: No. 216 astragal is used onthe vertical door edges at the center of thedoorway. No. 216 Weathersweep is usedalong the bottom of the doors).
No.1028 Cremone Bolt: Cremone bolts canbe used in place of cane and spring bolts.
◗ Hinge RequirementsDoors up to 8' high require 3 hinges.Doors 8'-1" to 12' high require 4 hinges.Doors 12'-1" to 16' high require 5 hinges.Doors 16'-1" to 20' high require 6 hinges.
◗ Weight TableSets of Hinges 434x376 Hardware 434x888 Hardware
Per Hardware Sets Shipping Weight Shipping Weight
3 Sets 725 Pounds 825 Pounds4 Sets 850 Pounds 950 Pounds5 Sets 1000 Pounds 1100 Pounds6 Sets 1175 Pounds 1275 Pounds
◗ Directions for OrderingA: Width and height of opening.B: Width, height, and thickness of doors.C: Door and jamb construction.D: Jamb and headroom conditions—Provide sketch or drawing showing available clearances.E: Specify if doors are to swing "In" or "Out".
SLIDE
-FOL
D 434
HARD
WARE
SETS
44
DOOR TRUCK / APRON ASSEMBLY DATA
7
SLIDE-FOLD 1035 DOOR HARDWARE• 2-6 Door Sets
45
◗ Slide-Fold Hardware 2-6 Door Sets 1035Designed for use on medium sized manually operatedslide-fold doors. These hardware sets are available fordoor applications using two through six door sectionssupported by jamb hinges, center hinges, and hangerswhich operate in lock-joint track. Locking bolts and hinges are avail-able in different combinations to meet most door applications.
Best results are obtained by using door widths of 3'-0" or less (4'-0"max. on two door set).
Door weight should not exceed 250 pounds per section. Doors weigh-ing more than 250 pounds should use No. 434 slide-fold hardware.
No. 1035 sets include: hangers, track, brackets, jamb hinges, centerhinges, bow handles, locking bolts withkeepers, bumper shoes, floor guides,and fasteners for attaching hardware todoor. (Wall bolts are excluded). Aheavy bar latch is supplied with thosesets having a passage swing door (3,4, 5, & 6 door applications).
6 D
oor
Sets
, Tra
ck S
erie
s 33
0, D
oor
Wei
ght u
p to
250
lbs.
Eac
h •
SLIDE
FOLD
NO. 10
35 HA
RDWA
RE PA
RTS
46
2 Door Sets for Openings up to 8 ft. Wide 3 Door Sets for Openings up to 9 ft. Wide
Kit Part Headroom Weight Kit Part Headroom WeightNumber Required Pounds Number Required Pounds
1035-A2-330 82" 129 1035-A3-330 82" 1491035-B2-330 82" 134 1035-B3-330 82" 136
42 Door Sets – 2 Folding Each Way 4 Door Sets – 3 Folding One Way for Openings up to 12 ft. Wide for Openings up to 12 ft. Wide
Kit Part Headroom Weight Kit Part Headroom WeightNumber Required Pounds Number Required Pounds
1035-A42-330 82" 238 1035-A4-330 112" 1931035-B42-330 82" 256 1035-B4-330 112" 202
5 Door Sets for Openings up to 15 ft. Wide 6 Door Sets for Openings up to 18 ft. Wide
Kit Part Headroom Weight Kit Part Headroom WeightNumber Required Pounds Number Required Pounds
1035-A5-330 112" 285 1035-A6-330 112" 2951035-B5-330 112" 297 1035-B6-330 112" 313
◗ Out Opening DoorsDoor applications which require the doors to open on the exterior side must be designated with an “O”as a prefix to the catalog number. Specific hardware parts are used on out opening doors to provide clear-ance to allow the doors to fully open.
◗ Locking Bolt CombinationsSets with the “A” combination use No. 514 top bolts and No. 524 can bolts. Sets with the “B” combina-tion use No. 1028 cremone bolts.
◗ Ordering Instructions1. Please state the number of sets desired and the catalog number as selected from the chart above.2. Add the prefix “O” to the catalog number if doors are to open out.3. Select the hinge combination desired.4. Provide the opening size (width x height), door thickness and construction to insure that proper
quantities of hardware and screws are furnished.5. Add suffix “No. 4” for disc bearing hinges. Add suffix “No. 5” for ball bearing hinges.
Example: 1 set 0-1035-B 42"-330-Hinge combination No. 4, for an opening 12'-0" x 8'-0" high, using1w" thick wood doors.
SLIDE FOLD NO. 1035 DOOR HARDWARE
DOOR TRUCK / APRON ASSEMBLY DATA
7
SLIDE FOLD NO. 1035 DOOR HARDWARE
47
Hardware Sets Using 330 Track for Doors WeighingUp to 250 Pounds Each
DescriptionCatalog ShippingNumber Weight Each
Hangers for in opening doors 435-P225 9 lb.
Hangers for out opening doors* 435-P226 9 lb.
Track † 330 4 lb./ft.
Center Bracket 435-P185 5 lb.
Intermediate Bracket 1035-P100 11 lb.
End Bracket 1035-P105 16 lb.
Jamb Hinge — Disc Bearing -19" 1035-P208 6 lb.-24" 1035-P209 7 lb.-30" 1035-P210 9 lb.-36" 1035-P211 10 lb.
Jamb Hinges — Ball Bearing -19" 1035-P213 6 lb.-24" 1035-P214 7 lb.-30" 1035-P215 9 lb.-36" 1035-P216 10 lb.
Center Hinges — Disc Bearing -15" 1035-P6 52 lb.(12 Off.)* -15" 1040-P10 6 lb.
Center Hinges — Ball Bearing -15" 1040-P7 5w lb.(12 Off.)* -15" 1040-P13 7 lb.
Bow Handle* 81-P1 2 lb.
Bow Handle 81-P2 1 lb.
Center Floor Guide 771-P3 7w lb.
Bumper Shoes (per pair) 102-P136 2 lb.
Door Holder 119-P3 4 lb.
Latch 225-P43 2w lb.
Cane Bolt 524-P21 32 lb.
Top Bolt 514-P36 2w lb.
Cremone Bolt 517-P27 11 lb.
* Use these parts on out opening sets.
† Track length determined by opening width.
1035 S
LIDE-
FOLD
DOOR
HARD
WARE
48
◗ Miscellaneous
Floor Guide0771.00003
Door Holder0119.00003(330)
Bow Handle0081.00001(330)(Out Opening)0081.00002(330)(In Opening)
0191.00001(376)
Latch0225.00043(330)
◗ Hinges
Jamb Hinge1035 Series (for 1035 sets)
Center Hinge1040 Series (for 1035 sets)
Truck/Hanger Assembly (330)0435.00226 (Out Opening)0435.00225 (In Opening)
330 Track376 Track
◗ Hangers
◗ Track and Brackets
Center Bracket0435.00185(330)0435.00199(376)
Intermediate Bracket1035.00100(330)1035.00144(376)
End Bracket1035.00105(330)1035.00119(376)
DOOR TRUCK / APRON ASSEMBLY DATA
7
SLIDE FOLD NO. 434 HARDWARE PARTS
49
434 x 376 Hardware 434 x 888 Hardwarefor Doors Weighing for Doors Weighing
Up to 500 Pounds Each Up to 1250 Pounds EachDescription
Catalog Shipping Catalog ShippingNumber Weight Each Number Weight Each
Hangers 2434-P24 12 lb. 2434-P28 16 lb.
Track † 376 5w lb./ft. 888 8 lb./ft.
Center Bracket 435-P199 6 lb. 434-P229 15 lb.
Intermediate Bracket 1035-P114 16 lb. 434-P230 20 lb.
End Bracket 1035-P119 20 lb. 434-P231 25 lb.
Jamb Hinges* 434- “B” Varies 434- “B” VariesBall Bearing 434- “F” Varies 434- “F” Variesor Disc Bearing 434- “W” Varies 434- “W” Varies
Center Hinges BB or BD* 434- “K” Varies 434- “K” Varies
Bow Handle 191-P1 2w lb. 191-P1 2w lb.
Center Floor Guide 771-P3 7w lb. 771-P3 7w lb.
Top Bolt †† 434-P96 7 lb. 434-P96 7 lb.
Cane Bolt †† 524-P23 5 lb. 524-P23 5 lb.
Optional EquipmentNeoprene Astragal 216 14 lb./ft. 216 14 lb./ft.
Weatherstrip 216 w lb./ft. 216 w lb./ft.
Cremone Bolt †† 1028 28 lb. 1017 28 lb.
† Track length determined by opening size.
* Hinge Size determined by door weight and size.
†† For use on manually operated doors only.
434 S
LIDE-
FOLD
DOOR
HARD
WARE
50
◗ Miscellaneous
Floor Guide0771.00003
Door Holder0119.00003(330)
Bow Handle0191.00001(888) Latch
0225.00043(330)
◗ Hinges
434-K Ball Bearing Center Hinge(for 434 sets)
434-B Ball Bearing Jamb Hinge(for 434 sets)
Truck/Hanger Assembly (888)2434.00028
Truck/Hanger Assembly (376)2434.00024
888 Track
◗ Hangers
◗ Track and Brackets
Bracket for 8880434.00230(Inter.)0434.00231(End)
◗ Fusible LinksFusible LinkListed by Underwriter’s Laboratories, Inc. in the following ranges for loads up to 30 pounds: 0097.00135 . . . . . . . . . . . . . . 135°F0097.00165 . . . . . . . . . . . . . . 165°F0097.00212 . . . . . . . . . . . . . . 212°F0097.00370 . . . . . . . . . . . . . . 370°FBoxed. Weight: 1/2 oz. each.
Pioneered by Richards-Wilcox and manufactured to rigid U.L. requirements,fusible links provide a heat-activated mechanism that assures positive clos-ing of doors, windows, hatchways, dampers, and blowers. The links fusewhen their rated temperature is reached, releasing the open door to block thepath of the fire. The links can be used individually, or in combinations. Inmulti-link assemblies the door load is equally spread over all links such thatthe door will be released even if only one link fails.
NOTE: Links should not be painted, since this will alter the fusing tempera-ture. Also, individual links may be used only for weights up to the specifiedcapacities and with a straight pull (force applied parallel to the axis of the link). If links are subjected toloads in excess of this rating, or if used in any manner other than a straight pull, they may break, endan-gering people and property. To insure the safest door operation, links should be replaced annually.RICHARDS-WILCOX SPECIFICALLY DISCLAIMS ANY WARRANTY IF THE ABOVE CONDITIONS ARE NOTMET.
◗ Multiple Link AssembliesMULTIPLE LINK ASSEMBLIES
There are many cases where a single fusible link is not strong enough to holdthe required load and in such cases we recommend that either a double or triplelink be used. Our regular No. 0097.00165 Fusible Link is used in combinations asshown at right.
These multiple link assemblies are designed in such a manner that ifany one of the links fuse - the whole assembly will separate. Theload is always equally spread over all of the links in the assembly.
NOTE: Links should not be painted, since thiswill alter the fusing temperature. Also, individ-ual links may be used only for weights up tothe specified capacities and with a straight pull(force applied parallel to the axis of the link).If links are subjected to loads in excess of thisrating, or if used in any manner other than astraight pull, they may break, endangering peo-ple and property. To insure the safest dooroperation, links should be replaced annually. RICHARDS-WILCOX SPECIFICALLY DISCLAIMS ANYWARRANTY IF THE ABOVE CONDITIONS ARE NOT MET.
DOOR HARDWARE
51
0097.00057 Double link assemblycarries up to 60 pounds.
0097.00064 Triple link assembly carries up to 90 pounds.
DOOR TRUCK / APRON ASSEMBLY DATA
7
DOOR
HARD
WARE
52
◗ Astragal WeatherstripFor use on the meeting vertical edges of swinging or slide-fold-ing doors from 1w" to 22" thick. Each weatherstrip assemblyincludes: neoprene, steel strips, and fasteners for onedoor to accommodate either steel or wood doors.
Finish: Steel strips painted; screws zinc plated.
Ordering Data: Specify part number for proper doorthickness and indicate door height - 8', 10', or 12'.
Door Neoprene Door FastenerPart Thickness Size Clearance Location
Number A B C D
0216.00028 1w" z" x 5a" x 8'0" 1w" s"0216.00029 1w" z" x 5a" x 10'0" 1w" s"0216.00030 1w" z" x 5a" x 12'0" 1w" s"0216.00032 22" z" x 6a" x 8'0" 24" s"0216.00033 22" z" x 6a" x 10'0" 24" s"0216.00034 22" z" x 6a" x 12'0" 24" s"
◗ Sweep WeatherstripSWEEP WEATHERSTRIPFor use on the bottom edge of doors, frame jambs, and frame lintels.Weatherstrip assembly includes: neoprene, steel strip, and fasteners.
Finish: Steel strips painted; screws zinc plated.
Ordering Data: Specify part number for proper door width or lengthrequired.
Door Neoprene FastenerPart Thickness Size Location
Number A B C
0216.00052 All 8" x 22" x 6'0" 1w"0216.00036 All 8" x 22" x 8'0" 1w"0216.00037 All 8" x 22" x 10'0" 1w"0216.00038 All 8" x 22" x 12'0" 1w"
◗ Handrail Bracket0566.00003 HANDRAIL BRACKET (Mounting hardwareincluded for wood and concrete)Designed to support wood or metal handrails on masonry or con-crete walls. Brackets are reversible for left or right hand use.
Construction: Malleable iron, base diameter 3".
Finish: Painted.
Maximum Projection from FacePart Handrail of Wall to CenterNumber Finish Size of Handrail
0566.00003 Painted 32" Wide 3a"
DOOR HARDWARE
53
0566.00003Handrail mount for flat and round
handrail mounting
DOOR TRUCK / APRON ASSEMBLY DATA
7
STAND
ARD A
ND HE
AVY-
DUTY
STRAP
HING
E SEL
ECTIO
N
54
Richards-Wilcox offers two lines of strap hinges to meet heavy-duty swing door applications.
◗ No. 1035, 1036 and 1047 Strap HingesDesigned for use on swinging wood or metal doors. The hinge pintles are made for surface mounting towood, formed metal, or structural steel frames. These hinges are available with disc bearings or ball bear-ings (1047 disc bearing only), and are available in several strap sizes and lengths to meet most normaldoor applications.
◗ No. 434 Strap HingesDesigned for use on large swinging wood or metal doors and also may be used on smaller doors whichhave a high frequency of operations each day.
The 434 Hinges are available in disc bearing and ball bearing styles. Four pintle styles are available in twostrap sizes and lengths to meet most normal door applications.
To properly select standard strap hinge for a given application, several factors must be considered:A) The frequency of door operation.B) The desired pintle pin location.C) The opening frame/jamb constructionD) The door size (width, height, thickness, and weight).
Selection is made as follows:1. Type of Bearing
– Disc bearing hinges are for manually operated doors with an expected usage of up to twentyoperations each day.
– Ball Bearing Hinges are for manually operated doors with an expected usage in excess of twentyoperations each day. Both bearings are zinc plated.
2. Style of Pintle– Select a style in respect to the desired pintle pin location and the frame/jamb construction.
3. Hinge Back Plates– When through bolting strap hinges to doors, hinge back plates should be used to prevent dam-
age to the door.4. Center Hinges
– The primary use of center hinges is on slide-folding door applications. The strap size for a centerhinge should be equal to the size for a jamb hinge.
5. No. 434 Strap Hinges – Recommended Usage Data
Jambs Doors to Swing AvailableHollow Block Clear of Opening Standard Strap
Brick or at 90 Degrees Sizes a" x 22" Strap LengthsNo. 434 Steel Concrete* Yes No and 32" x 3" & 4" Up to 6'0" Remarks
B* ● ● ● ● ●
F* ● ● ● ●
FW* ● ● ● ●
W* ● ● ● ●
*Hollow block walls must either be filled or have reinforcement provided.
For flush doors, widepintle for masonry.
Featuring narrow pin-tle for attachment tosteel frame.
Features narrow pintlefor use with steelframe.
Most popular hingefor general use.
◗ Calculating the Proper HingeThe selection charts are arranged in ascending order of capacity, both in door weight and hinge moment,by hinge part number.
1. Obtain the following information:a. Weight of the door in poundsb. Height of the door in feetc. Width of the door in feet
2. Calculate the moment on the hinge set:a. Multiply the weight of the door by the width of the door
3. Locate the column showing the door height and go down the column to the row indicating the heightof the specified door. Read across the row, find the proper hinge model which has values matchingthe application. The row will also tell you the number of hinges necessary.Important Note: The specified door weight and hinge moment must be less than or equal to the pub-lished values in the chart for the model of hinge used.
◗ ExamplesExample One – knowing the door specification, choose the hinge model.
a. Door weight = 1500#Door height = 8 feetDoor width = 4 feet
b. Hinge moment = 6000 ft./#(1500 x 4 = 6000)
c. Look in door height column to row for 8 footd. Go across the row until the door weight and moment are less than or equal to the above num-
bers—i.e. hinge model 0434.00320 (3 per door)
Example Two – knowing the hinge model needed, calculate the door specification.a. Select the hinge model by part numberb. Reading down the column for the hinge, find the maximum door weight and hinge moment per
door height rowc. b. will give you the approximate door weight and hinge moment for different door heights. Simply
match up these specifications for your application.
STANDARD AND HEAVY-DUTY STRAP HINGE SELECTION
55
DOOR TRUCK / APRON ASSEMBLY DATA
7
STAND
ARD A
ND HE
AVY-
DUTY
STRAP
HING
E
56
◗ Standard Duty Hinge Selection Chart1036.000311036.00032
1047.00009 1036.00037 1035.00270 1035.00266 1035.002721047.00010 1047.00012 1036.00038 1035.00271 1035.00267 1035.00273
Number Maximum Maximum Maximum Maximum Maximum Maximum Maximumof Height Weight/ Weight/ Weight/ Weight/ Weight/ Weight/
Hinges Feet Moment Moment Moment Moment Moment Moment
2 4 491/1907 767/3323 1104/842 1104/954 1104/1038 1104/1491
3 8 736/4450 1150/7754 1657/1965 1657/2226 1657/2422 1657/3479
4 12 982/6993 1534/12184 2209/3088 2209/3498 2209/3807 2209/5466
5 16 1227/9536 1917/16615 2761/4210 2761/4771 2761/5191 2761/7454
6 20 1473/12079 2301/21046 3313/5333 3313/6043 3313/6043 3313/9442
7 24 1718/14623 2684/25476 3866/6456 3866/7315 3866/7959 3866/11429
1040.00007 1035.00268 1040.00006 1036.000341040.00013 1035.00269 1040.00010 1036.00040 0434.00304 0434.00320
Number Maximum Maximum Maximum Maximum Maximum Maximum Maximumof Height Weight/ Weight/ Weight/ Weight/ Weight/ Weight/
Hinges Feet Moment Moment Moment Moment Moment Moment
2 4 1104/1572 1104/1622 1104/1759 1104/1796 1963/1999 1963/2718
3 8 1657/3668 1657/3785 1657/4104 1657/4192 2945/4664 2945/6341
4 12 2209/5763 2209/5948 2209/6450 2209/6587 3927/7330 3927/9965
5 16 2761/7859 2761/8111 2761/8795 2761/8982 4909/9995 4909/13588
6 20 3313/9955 3313/10273 3313/11140 3313/11377 5890/12661 5890/17211
7 24 3866/12051 3866/12436 3866/13485 3866/13772 6872/15326 6872/20835
0434.00288 0434.00280 0434.00292 0434.002840434.00290 0434.00314 0434.00328 0434.00282 0434.00294 0434.00286
Number Maximum Maximum Maximum Maximum Maximum Maximum Maximumof Height Weight/ Weight/ Weight/ Weight/ Weight/ Weight/
Hinges Feet Moment Moment Moment Moment Moment Moment
2 4 1963/3957 1963/4483 1963/4715 1963/5276 1963/7544 1963/11360
3 8 2945/9233 2945/10459 2945/11002 2945/12311 2945/17603 2945/26508
4 12 3927/14509 3927/16436 3927/17288 3927/19346 3927/27661 3927/41655
5 16 4909/19785 4909/22413 4909/23575 4909/26380 4909/37720 4909/56802
6 20 5890/25061 5890/28390 5890/29861 5890/33415 5890/47778 5890/71950
7 24 6872/30337 6872/34367 6872/36148 6872/40450 6872/57837 6872/87097
STANDARD AND HEAVY-DUTY STRAP HINGE
57
◗ Heavy-Duty Hinge Selection Chart0434.00308 0434.00300 0434.00323 0434.003310434.00302 0434.00312 0434.00318 0434.00325
Number Maximum Maximum Maximum Maximum Maximumof Height Weight/ Weight/ Weight/ Weight/
Hinges Feet Moment Moment Moment Moment
2 4 1963/2695 1963/4790 1963/1902 1963/3931
3 8 2945/6287 2945/11178 2945/4438 2945/9171
4 12 3927/9980 3927/17565 3927/6974 3927/14412
5 16 4909/13473 4909/23952 4909/9510 4909/19653
6 20 5890/17066 5890/30339 5890/12046 5890/24894
7 24 6872/20659 6872/36727 6872/14583 6872/30135
Standard Strap Hinges are available in four styles and two bearing types to meet swing door and slidefolding door applications.
◗ 1035 Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin.Hinges available with disc bearings or ball-bearings,non-template.
Application: Full strap hinge with offset pintle. Pintlecan be mounted on opening frame or set back on faceof wall to allow open doors to clear the doorway.
Finish: Strap and pintle painted.Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
1035.00266 Disc 19" x 22" x 4" 1w" x 8"1035.00267 Disc 24" x 22" x 4" 1w" x 8"1035.00268 Disc 30" x 22" x c" 1w" x 8"1035.00269 Disc 36" x 22" x c" 1w" x 8"1035.00270 Ball 19" x 22" x 4" 1w" x 8"1035.00271 Ball 24" x 22" x 4" 1w" x 8"1035.00272 Ball 30" x 22" x c" 1w" x 8"1035.00273 Ball 36" x 22" x c" 1w" x 8"
◗ 1036 Series Strap HingesConstruction: Steel, pintle pin non-removable hinges.Available with disc bearings or ball-bearings, non-template.
Application: Half surface strap hinge with butt typepintle leaf for mounting to inside of frame. Pintle pinlocated at edge of opening.
Finish: Strap and pintle painted.Pintle pin and bearings zinc plated.
Catalog Number Bearing Type Strap Size Pintle Size Width x Height
1036.00031 Disc 18" x 22" x x" 2w" x 6"1036.00032 Disc 24" x 22" x x" 2w" x 6"1036.00034 Disc 36" x 3" x 4" 2n" x 7"1036.00037 Ball 18" x 22" x x" 2w" x 6"1036.00038 Ball 24" x 22" x x" 2w" x 6"1036.00040 Ball 36" x 3" x 4" 2n" x 7"
STAND
ARD S
TRAP H
INGES
58
1035 Series Strap Hinge
1036 Series Strap Hinge
DOOR TRUCK / APRON ASSEMBLY DATA
7
STANDARD STRAP HINGES
59
◗ 1040 Series Strap HingesConstruction: Steel, pintle pin non-removable, avail-able with disc bearings or ball-bearings, non-template.
Application: Full surface strap hinge for use as a center hinge on slide-folding doors. Offset in hingestraps: w" or 12" to allow hardware between doors.
Finish: Strap and pintle-painted. Pintle pin and bearings-zinc plated.
Part Number Bearing Type Offset Strap Size Pintle Size Width x Height
1040.00006 Disc w" 4" x 22" x 15" 15" x 4,"1040.00010 Disc 12" 4" x 22" x 15" 15" x 4,"1040.00007 Ball w" 4" x 22" x 15" 15" x 4,"1040.00013 Ball 12" 4" x 22" x 15" 15" x 4,"
◗ 1047 Series Strap HingesConstruction: Steel, pintle pin non-removable hinges.Available in disc bearing only, non-template.
Application: Full surface strap hinge with butt typepintle leaf for mounting to face of opening frame, pintle pin located at edge of opening.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Catalog Number Bearing Type Strap Size Pintle Size Width x Height
1047.00009 Disc 18" x 22" x x" 2s" x 6"1047.00010 Disc 24" x 22" x x" 2s" x 6"1047.00012 Disc 36" x 3" x 4" 2s" x 7"
◗ Jamb Sections for Standard Strap Hinges
1040 Series Strap Hinge
1047 Series Strap Hinge
1035 HingeBack Plate *Machine Bolts
1035 Hinge – Frame Mounted
1036 Hinge Back Plate
1036 Hinge – Frame Mounted
*Carriage Bolts
1035 Hinge – Wall Mounted
*Carriage Bolts
1047 Hinge – Frame Mounted
1040 Center Hinge – Door Mounted
1040 Center Hinge
The 434 Industrial Strap Hinges are available in five hinge styles and two bearing types to meet mostswing door and slide folding door applications.
◗ 434-B Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin;hinges available in two strap sizes with disc or ballbearings; pintle and strap have b" dia. holes for fas-teners, non-template.
Application: Full surface strap hinge with offset strap and pintle pin set back from edge of opening toallow door to fully clear opening when in the 90 degree open position; wide pintle for through-bolting onmasonry wall.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
0434.00302 Disc a" x 3" x 332" 92" x 7"0434.00312 Disc 2" x 4" x 332" 92" x 9"0434.00318 Ball a" x 3" x 332" 92" x 8"0434.00325 Ball 2" x 4" x 332" 92" x 10"
◗ 434-F Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin;hinges available in two strap sizes with disc or ballbearings; pintle and strap have b" dia. holes for fas-teners, non-template.
Application: Full surface strap hinge with offset strap and pintle pin set back from edge of opening toallow door to fully clear opening when in the 90 degree open position; narrow pintle for attachment tosteel frame.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
0434.00308 Disc a" x 3" x 272" 34" x 7"0434.00310 Disc 2" x 4" x 272" 34" x 9"0434.00323 Ball a" x 3" x 272" 34" x 8"0434.00331 Ball 2" x 4" x 272" 34" x 10"
INDUS
TRIAL
STRA
P HING
ES
60
434-B Strap Hinge
434-F Series Strap Hinge
DOOR TRUCK / APRON ASSEMBLY DATA
7
INDUSTRIAL STRAP HINGES
61
◗ 434-FW Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin. Hingesavailable in two strap sizes with disc or ball bearings; pintleand strap have b" dia. holes for fasteners, non-template.
Application: Full surface strap hinge with pintle pin located at edge of opening; narrow pintle for attach-ment to steel frame.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
0434.00280 Disc a" x 3" x 24" 34" x 7"0434.00284 Disc 2" x 4" x 24" 34" x 9"0434.00288 Ball a" x 3" x 24" 34" x 8"0434.00292 Ball 2" x 4" x 24" 34" x 10"
◗ 434-W Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin; hingesavailable in two strap sizes with disc or ball bearings; pintleand strap have b" dia. holes for fasteners, non-template.
Application: Full surface strap hinge with pintle pin located at edge of opening; wide pintle for attach-ment to wall.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
0434.00282 Disc a" x 3" x 24" 92" x 7"0434.00286 Disc 2" x 4" x 24" 92" x 9"0434.00290 Ball a" x 3" x 24" 92" x 8"0434.00294 Ball 2" x 4" x 24" 92" x 10"
◗ 434-K Series Strap HingesConstruction: Steel, pintle pin secured with cotter pin;hinges available in two strap sizes with disc or ball bearings;pintle has b" x 14" slots- strap has b" dia. holes for fasteners, non-template.
Application: Full surface strap hinge for use as a center hinge on slide-folding doors.
Finish: Strap and pintle painted. Pintle pin and bearings zinc plated.
Part Number Bearing Type Strap Size Pintle Size Width x Height
0434.00304 Disc a" x 3" x 24" 24" x 6"0434.00314 Disc 2" x 4" x 24" 24" x 8"0434.00320 Ball a" x 3" x 24" 24" x 8"0434.00328 Ball 2" x 4" x 24" 24" x 10"
434-FW Series Strap Hinge
434-W Series Strap Hinge
434-K Series Strap Hinge
◗ Strap Hinge Back PlatesConstruction: Steel, hole centers match straphinge sizes as shown in chart.
Application: When through bolting 434, 1035,1036 and 1047 strap hinges to a non-reinforced door (exam-ple: hollow metal). Available for 18", 19", 24", 30" and 36" strap lengths in disc or ball bearing styles. Theback plate distributes the force of the fasteners over a larger surface area, thus preventing damage to thedoor.
Finish: Painted.
Hinge Number Back Plate Number Size
1035.00266 1035.00241 x" x 22" x 162"1035.002701035.00267 1035.00242 x" x 22" x 212"1035.002711035.00268 1035.00243 4" x 22" x 274"1035.002721035.00269 1035.00244 4" x 22" x 334"1035.002731036.00031 1036.00058 x" x 22" x 16"1036.000371036.00032 1036.00059 x" x 22" x 22"1036.000381036.00034 1036.00060 x" x 3" x 34"1036.000401047.00009 1036.00058 x" x 22" x 16"1047.00010 1036.00059 x" x 22" x 22"1047.00012 1036.00060 x" x 3" x 24"All 434 0434.00296 4" x 3" x 212"
STAND
ARD /
INDU
STRIAL
STRA
P BAC
K PLA
TE
62
Strap Hinge Back Plate
434-B
◗ Jamb Sections for Industrial Strap Hinges434 Hinge Back Plate
434-F
434 Hinge Back Plate
434-FW
434 Hinge Back Plate
434-W
434 Hinge Back Plate
434-FW
434-K Center Hinge
434 Hinge Back Plate434-B Jamb Hinge Shown
DOOR TRUCK / APRON ASSEMBLY DATA
7
RICHARDS-WILCOX TEN-YEAR GUARANTEE
63
◗ Hardware ProductsRichards-Wilcox Hardware Products are warranted to be of good quality, and free from defects in mate-rial and workmanship under normal intended use for a period of ten (10) years from the date of purchase.If any hardware, or part thereof, is determined by Richards-Wilcox not to be as warranted, Richards-Wilcox will at its option and without charge, replace the defective part or parts.
UNDER NO CIRCUMSTANCES SHALL WE BE LIABLE FOR INDIRECT OR CONSEQUENTIAL DAMAGES OFANY KIND. THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIEDINCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTIC-ULAR PURPOSE. THE WARRANTIES COVER RICHARDS-WILCOX MATERIAL. WE SHALL NOT BELIABLE, NOR DO WE ASSUME RESPONSIBILITY FOR DAMAGE OR OPERATIONAL FAILURES CAUSEDBY SUPPORTING AND/OR SURROUNDING STRUCTURE AND/OR EQUIPMENT, OVERLOADING OF THEPRODUCT BEYOND THE MANUFACTURER’S RATED CAPACITY, IMPROPER USE OR APPLICATIONBEYOND THE MANUFACTURER’S INTENDED OR RECOMMENDED USE, OR OTHER EXTERNAL CAUSESSUCH AS ABUSE OR ACTS OF GOD AND OTHER CAUSES BEYOND OUR CONTROL. MAINTENANCE ANDADJUSTMENTS ARE THE RESPONSIBILITY OF THE OWNER. THIS GUARANTEE DOES NOT COVERSUCH MAINTENANCE AND ADJUSTMENTS, NOR ANY SERVICES WHICH MAY BE REQUIRED AS ARESULT OF THE PURCHASER’S FAILURE TO PERFORM NORMAL MAINTENANCE AND ADJUSTMENTSTO THE PURCHASED PRODUCT.
Replacement of defective material shall be furnished without charge, delivered, installation not included.If Richards-Wilcox decides to service a warranted product at the purchaser’s place of business and deter-mines that no defective material or improper workmanship exists, then the purchaser shall reimburseRichards-Wilcox Company for all expenses, including time and travel, incurred in providing the service.
This guarantee is not applicable to other Richards-Wilcox non-hardware products.