Budget EstimateBUDGETARY COST ESTIMATEFORMAT REVISION NO. & DATEFFFFFFFBASED ON LAYOUT PLAN R12AGENERAL DETAILS1NAME OF CLIENTdsagsd4PREPARED BYKrishnaswamy MS2PROJECT NUMBER509825VERSION & DATER0 - 28 FEB 20093SITE ADDRESSDLF PARK, Shivaji Gardens, Mount Poonamalee High Road, Manapakkam, ChennaiBLEASED AREA IN SFT26,400CPACKAGECOST/SFTTOTAL COSTSCOPE OF WORKS CONSIDEREDREMARKS1CIVL & INTERIOR WORKS439.4211,600,590Civil & Interior workCivil Works Incl. Toilet-civil, plumbing and finishing work. Interior works- Gyp partitions, doors/ glazing, fixed furniture, hard flooring, gypsum ceiling, reception fitout, etc and furniture built on site2SCREEDING51.651,363,500Considered 75mm thk screeding @ INR 45/-3RAISED FLOORING23.41618,000Considered for UPS,SERVER RM & LAB4ELECTRICAL339.368,959,053aFloor PanelsElectrical wiring, Power and Data distributions systems, Aluminum aroumered cables for LV distribution, unarmoured copper cables for UPS, earth pits, LT panels, earthing strips, Conduiting, Raceway for the data cable distribution & cable tray for PDBs, UPSbBus-duct Rising Main with tapoffcMain Panel boards & LT breakersdLightning ProtectioneLT Cabling from LT Panel rising main and to Distribution Only5LIGHT FIXTURE97.522,574,400Lighting for all areas includes grid fittings for open office, PL lights, halogens, 2 x2 ingrid fittings, etc.Including ON/OFF sensors for work-station & closed cabin areas & Light fixtures for Cafeteria.6HVAC253.036,680,000aDucting works, Insulation works, VAVs, Grills, diffusers, Attenuatirs, Dampers, Valves and HVAC BMSChiller, Pumps, AHUs, HVAC BMS, & Installation works including VAVs, Dx units & Split UnitsbFresh AircToilet Exhaust with ductingd118 TR comfort Cooling with AHUS7PAC FOR UPS8.72230,100For UPS RM, SERVER RM8PAC FOR LAB78.942,084,000For LAB9UPS174.244,600,000For UPS RM, SERVER RM10DC RECTIFIER75.762,000,0001200A DC Plant with 30 min. Battery Back-up11FIRE SAFETY SYSTEMaSprinkler Modifications17.99475,000With adjustable flexible UL listed pipe.bFire Detection-FAS,PA & Panic Bar98.482,600,000Fire alarm system of Notifire integrated with Public address systemcGas Based Fire suppresion systems for Lab60.611,600,000dGas Based Fire suppresion systems for Server Room62.501,650,00012SECURITY & SURVEILLANCE (Access control & CCTV)68.181,800,00013BMS SYSTEM54.551,440,000BMS incl. computers, BMS software, DDC panels, Integrators, HVAC BMS, Field devices and cabling etc.14NETWORKING75.001,980,000Structured cabling, Jackpanels, IO-s, Back bone cabling and server racksDuty Benefit considered15CARPET68.902,480,402Carpet tile @ Rs.85/- per sftDuty Benefit considered16MODULAR FURNITURE479.9212,670,000Including Workstation,Manager Table,Meeting Tables,Training Table,Low-ht storageAll work stations and personal storage units (375 Nos @ Rs. 26,000/- per Workstation)17CHAIRS198.865,250,000All workstations and Conference Room chairsChairs considered @ Rs. 10,000/- X 525 Nos.18LOOSE FURNITURE52.121,376,000Cafe Tables,chairs, Reception sofas,break-out sofas19CAF EQUIPMENTS20.00528,000Dishwasher, Bainmarie, Pantry furniture etc.,20BLINDS11.25297,000Spring loaded blinds considered21GRID CEILING134.553,552,000Opens Offices, Cabins & Meeting RoomsModular (0.7 NRC), 85% reflectivity tiles22AV SYSTEMS50.001,320,000Projectors, Plasma and source systems23SIGNAGE7.58200,00024GRAPHICS & ARTWORKS7.58200,00025PROJECT SECURITY--Included in C&I Scope26PROJECT HOUSE KEEPING--Included in C&I Scope27ARCHITECT'S FEES50.0028PROJECT MANAGER'S FEES50.0028CONTINGENCIES20.00528,000TOTAL3,130.1080,656,045DEXCLUSIONS1Networking active & Passive components2Cost of all Office Equipments like computers,printers,Xerox/Fax, EPABX & Telephones e.t.c.3Base-Build provisions, Civil works (specific to tenant improvements) etc4OFC service connection charges (if any)5Cost of moving from incubation space6Satellite connectivity equipments & related connection charges(if any)7Cost of bonding ware house (temporary) construction8STPI clearances (consultanting fees)9PMG, Interior Designer and other consultants fee10Cost of Temporary Site Office, House keeping and Security11Cost of Statutory approval or Deposits, etc to avail approval and permissions

&C&G&C&Pof &N

01 Civil & InteriorsCIVIL AND INTERIORS BOQLeased Area31460Carpet Area26400SUMMARY OF COSTSPART AMiscelleneous Items of Work161,450PART BCivil and Wet Works1,916,845Partition and Panelling Works4,935,275Doors and Windows1,326,581Ceiling and Flooring Works484,360Built In Furniture559,375.00Loose Furniture775,979.00Finishes1,440,725PART CRest Room Accessories0GRAND TOTAL11,600,590Name of ContractorSignature and Seal of ContractorDateProjectProposed Fitout Works ForClientAT&TProject. No.50867Date10.02.2009RevisionR0Item of WorkMiscelleneous Items of WorkPART ABill of Quantities for Miscelleneous Items of WorkA 01AIPL ESTIMATENotes1Rates quoted for all demolition and dismantling works shall include for carting away all unwanted debris away from site.2If instructed by the client / Project Manager / Architect salvagable items dismantled shall need to be handed over to the Client / Developer as may be applicable.3Contractors to note that during the works of dismantling of any works, if damage is caused to other finished items in the vicinity either of other vendors or of the developer, the same shall be made good at his own cost and time.4The Contractor shall take necessary precautions to ensure that during works of demolition and dismantling nor damage is caused to any structural component of the building premises.SNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALA.01DEMOLITION WORKSA.01.01Dismantling/removal of existing brick / block wall at locations as indicated on the drawings to accommodate design changes and carting away all debris away from site. No additional shall be payable for leads and lifts1515Sqm140.002,100.00A.01.02Dismantling, removing and carting away existing doors, door frames and lintels at locations as indicated on the drawings. (Note if so instructed by client the same shall be handed over to the client / developer)11Nos500.000.00A.01.03Dismantling of existing wall cladding / flooring at locations as indicated on the drawings and carting away debris from site.QROSqm300.00A.01.04Chipping of existing PCC Floor at locations as indicated on the drawings to accommodate new hard flooring and carting away all debris from site.300300Sqm450.00135,000.00A.01.05Chipping of Existing PCC Floor at locations as indicated on the drawings for floor raceways to average width of 300 mm and carting away debris from site. (Note wider trenches required shall be measured in multiples of 300 mm width and paid for.)250250Rm90.0022,500.00A.01.06Making Cutouts in RCC Slab at locations if required inclusive of necessary additional bracing reinforcement and cutting away of existing reinforcement as per the instructions of the Architect. Rate to include making good the cut edges of the opening with neat plastered finish as approved.11Sqm1,850.001,850.00SUB TOTAL OF DEMOLITION WORKS161,450.00A.02CONSTRUCTION EXPENSESA.02.01Providing full time House Keeping services to maintain the site clean of all debris throughout the duration of the project. House Keeping services shall encompass all general cleaning on behalf of all agencies.NOT APPLICABLELOTSUB TOTAL OF CONSTRUCTION EXPENSES0.00A.03REPAIR EXPENSESA.03.01Repair of existing staircase to be used for movement of men and materials and make good all damages - to include repainting, making good damage to walls, replacing of broken treads and risers if any all complete.1LOTSUB TOTAL OF REPAIR EXPENSES0.00TOTAL OF MISCELLENEOUS ITEMS OF WORK CARRIED TO SUMMARY161,450Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Civil and Wet WorksAIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALGeneral Notes:1All Civil Works of brick work, blockwork, plastering shall be cosidered for all leads and lifts, scaffolding etc wherever applicable. No additional shall be payable for works at higher levels. Contractor shall have been deemed to have visited site to assess the site conditions before quoting for the works.2Rates quoted for all wet works shall be inclusive of necessary curing. Any defects arising in the works due to improper curing of the works shall be rectified by the contractor at his own cost and time.3For all items of flooring and cladding, only visible area after laying shall be measured and paid for. No allowances shall be acceptable for cut wastages.4Rates quoted for all counters like Vanity counters, pantry counters etc shall be inclusive of making necessary cutouts for plumbing fixtures, sinks, basins etc. Rates shall also be inclusive of polising of the edge of the cutout as per the profile shown on the drawings.5Samples of all items of works like tiles, granites, marbles, etc shall be got approved by the Architect and Client before the placing of mass orders for the project.6All items of water proofing shall carry standard manufacturer warranty / guarantee of 10 years for the soundness of application and water tightness. The contractor shall make good at his own cost any damage to the treated surface if while carrying out other works over the same.SNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.01CIVIL AND WET WORKSB.01.01Masonary and PlasterB.01.01.1Providing and constructing 200mm thk Solid block wall with 1:3 cement-sand mortar including 1:6 cement- sand plaster on both sides. Wall should be ready to receive paint / POP. Include cost of chicken mesh where new wall is in contact with old wall. Include a groove of 4mm x 4mm where ever new wall meets partition / old wall. Wherever wall is constructed on existing smooth finish screed, the surface of the screed shall be hacked rough and watered to ensure adherence of mortar. (Note that the cost of wall to be inclusive of plaster on both sides.) Plastered surface shall be in line level and plumb ready to receive POP Punning / tiles / other cladding.2525Sqm1,14028,500.00B.01.01.2Providing and constructing same as B.01.01.1 above but using 150mm thk solid concrete blocks. Cost of wall to include for RCC stiffener 75 mm thk after every 6th course / 1.0 mts throughout the running length of the wall.QROSqm1,040B.01.01.3Providing and constructing same as B.01.01.2 above but using 100mm thk solid concrete blocks. Cost of wall to include for RCC stiffener 75 mm thk after every 6th course / 1.0 mts throughout the running length of the wall.55Sqm8904,450.00B.01.01.4Providing and constructing same as B.01.01.1 above but for 230mm thk brick wall.QROSqm1,500B.01.01.5Providing and constructing same as B.01.01.3 above but for 115 mm thk brick wall.QROSqm1,300B.01.01.6Providing and constructing same as B.01.01.2 above but using 150mm thk Light weight Fly Ash blocks of Aerocon / Siporex or equivalent make.QROSqm1,750B.01.01.7Providing and constructing same as B.01.01.2 above but using 100mm thk Light weight Fly Ash blocks of Aerocon / Siporex or equivalent make.QROSqm1,650B.01.01.8Providing and applying Normal Sand Cement Plaster 1:6 over existing Walls / Columns / RCC Surfaces to line level and plumb to smooth finish ready receive POP Punning / or cladding. Cost to include for hacking existing surface for proper bonding all complete inclusive of necessary curing. (For the following thicknesses)a12 mm Average Thickness1010Sqm1801,800.00b19mm Average Thickness2020Sqm1803,600.00c25 mm Average Thikness (in layers)0Sqm3000.00d37.5mm Average Thickness with Chicken mesh0Sqm3500.00e50mm Average Thickness with Chicken mesh0Sqm4500.00B.01.01.9Providing and finishing Plaster of Paris Punning over plastered wall surface to be finished in line and plumb with smooth surface ready to receive paint base.a12 mm Average Thickness0Sqm1800.00b19mm Average Thickness625625Sqm180112,500.00c25 mm Average Thikness (in layers)0Sqm3000.00B.01.01.10Providing and fixing RCC Lintels over the door openings in Masonry walls in 1:2:4 RCC as per the following sizes.a100 mm W x 100 mm H0Rm4000.00b150 mm W x 150 mm H0Rm4500.00c200 mm W x 200 mm H44Rm4801,920.00B.01.02Water Proofing WorksB.01.02.1Providing and applying Membrane type water proofing with 3 coats of brush applications over the slab surface. Cost of the water proofing shall include cleaning of the surface of all dirt and grit before the application. The brush application shall be carried for atleast 350mm on the vertical surface on all sides of the area to be water proofed. The water proofed area shall be ponded and tested for a minimum of 48 hours or as per manufacturer's specification. Brush Application of Fosroc / Roff or equivalent.55Sqm3951,975.00B.01.02.2Providing and filling Cinder to an average depth of 200 mm at locations as indicated on the drawings or as instructed by the architects. Cost to include for proper compaction of the laid cinder and filling the complete area with 1:3:6 cement concrete to fill all gaps in the cinder to form a level even surface on top.QROCum370B.01.02.3Providing and laying top PCC layer minimum 25mm thk mixed with with water proofing compound over the cinder filled area using 1:3:6 PCC all complete of necessary curing. Top surface to be level to receive finishing such as tiles / granite / marble etc.QROSqm277B.01.02.4Providing and applying Water Proofing by Crystallization method over mother slab as per manufacturer's specifications all complete at locations indicated on the drawings. (Xypex or Equivalent)QROSqm700B.01.03Paving WorksB.01.03.1Providing and laying 1:2:4 nominal mix Plain cement concrete screed over raw slab areas to match the level of of the exisitng screed at other areas or to average thickness of 75mm as instructed. The rate to included for power floated finish to achieve line level and smooth top surface to receive finishing materials as instructed.100100Cum4,500450,000.00B.01.03.1aProviding and laying 1:2:4 nominal mix Plain cement concrete screed over existing screed after manual hacking of the existing surface, applying a coat of Nitobond as per package instructions and laying new screed with admixture of recron fibre in proportion as per manufacturer's specifications.00Cum4,4500.00Applicable for areas where screed already exists but is insufficient for raceway depthsB.01.03.2Providing and laying 1:2:4 nominal mix Plain cement concrete screed to fill in chases made in the floor after the installation of all services like raceways, conduits etc. The PCC mix shall have necessary additives of Fosroc or equirevalent of non shrink grout to avoid shrinkage cracks. Wherever applicable due to non availability of sufficient depth the PCC shall be laid with chicken mesh for better bonding.2020Cum4,45089,000.00B.01.03.3Providing and applying Rapid Drying Cementitious Underlayment compond ARDEX P51 primer in 1:3 proportion mixed with water and applying a second coat of ARDEX P51 Primer 1:1 with water and finally laying 3mm thk Self level rapid setting,rapid curing ARDEX CL11 on the existing Screed225225Sqm41092,250.00B.01.03.4Providing & laying PCC in shafts to make shafts 2 hrs fire rated along with MS understructure with chequered plate to ensure PCC fire barrier is in proper place. MS framework to be made of 3mm thk MS L-Angle section finished with metal primer, 2 coats of red oxide paint & Fire rated paint.QROSqm20,000B.01.03.5Providing & fixing fire barrier synthetic elastomer in vertical shafts at floor levels of "3M Fire Barrier Moldable Putty" with "3M Fire Barrier CS-195+ Composite Sheet" to make shafts fire retardant for 2 hours. The composite sheet shall be made of fire resistive elastometric material with one side being 28guage galvanized steel & other side being a steel-wire mesh & covered with aluminum foil. is used to provide support to moldable putty. Note that composite sheet shall be cut to profile of cables & conduits passing thru the shaft.3M / PromatQROSqm19,000B.01.04Flooring WorksB.01.04.1Providing & laying Italian marble flooring @ appropriate areas as per design. Work rate to be quoted per dimensions mentioned below. Marble to be fixed with cement sand mortar and top layer of white cement, marble shall be mirror polished to architect's approval. The rate shall be inclusive of adding extra mortar (where ever required), chamfering edges, necessary preparation, cleaning, protection with POP, etc. complete. (Color & Lot of Italian marble shall be to Architect's approval). Extra thickness of mortar (45-55mm) to be considered & water proof sealer on all sides to be considered. Marble shall be as mentioned below.Type A-900 X 900 slab (exact size to approval of architect) on flooring, ramps (with 25mm x 25mm groove in slope), vertical facia in ramp, steps (riser facia to be included in this item), as per detail, etc. (Basic Rate of Rs. 600 + Tax)7070Sqm10,500735,000.00Type B-900 X 900 slab (exact size to approval of architect) on flooring, ramps (with 25mm x 25mm groove in slope), vertical facia in ramp, steps (riser facia to be included in this item), as per detail etc. (Basic Rate of Rs. 450 + Tax)QROSqm8,400B.01.04.2Providing & laying Granite flooring @ areas as per design. Work rate to be quoted per dimensions mentioned below. Granite to be fixed with cement sand mortar and top layer of cement slurry in line and level and as per patterns indicated on the drawings. The rate shall be inclusive of adding extra mortar (where ever required), chamfering edges, necessary preparation, cleaning, protection with POP, etc. complete. (Color & Lot of Granite shall be to Architect's approval). Extra thickness of mortar (45-55mm) to be considered & water proof sealer on all sides to be considered. Granite shall be as mentioned below. (Basic cost of Granite Rs. 220 + Tax))aType A-900 X 900 slab (exact size to approval of architect) on flooring, ramps (with 25mm x 25mm groove in slope), vertical facia in ramp, steps (riser facia to be included in this item), as per detail, etc. Polished Finish0Sqm4,1000.00bType B-900 X 900 slab (exact size to approval of architect) on flooring, ramps (with 25mm x 25mm groove in slope), vertical facia in ramp, steps (riser facia to be included in this item), as per detail etc. Flamed Finish0Sqm4,4000.00B.01.04.3Providing, fixing & Laying "Under mentioned Tile" on floor as per design & manufacturer's instruction. Cost to include Preparation of subfloor to plumb level with normal PCC course, base mortar upto 40mm thk in ratio 1:4 ( 1 part of cement to 4 parts of sand) with appropriate slope as per architects instructions, Laying tiles on a thin cement slurry paste & necessary protection after laying. Gap for expansion of tiles to be left as per manufacturers instructions. Tile joints to be filled with water sealant (2mm wide grout) of approved color by architects. Laying & fixing details as suggested by the manufacturer to be followed. Extra thickness of mortar (45-55mm) to be considered.aGreen Kota slab Tiles (600mm x 600mm) all exposed edges to be polished.44Sqm9503,800.00bVitrified tiles-1 basic cost Rs.140/sft + TaxQROSqm2,420cVitrified tiles-2 basic cost Rs. 120/sft + Tax175175Sqm1,910334,250.00dVitrified tiles-3 basic cost Rs.90/sft + TaxQROSqm1,740eVitrified tiles-3 basic cost Rs.65/sft + TaxQROSqm1,125fCeramic Tiles 1- Basic Cost - Rs.45/sft + TaxQROSqm1,400gCeramic Tiles 2- Basic Cost - Rs.65/sft + TaxQROSqm2,068B.01.04.4Providing & fixing pre polished Skirting of undermentioned Tile / slab of 100 mm as per design & manufacturer's instruction. Cost to include Preparation of sub surface to plumb level, preparation of thin layer of cement slurry in ratio 1:3 (1 part of cement to 3 parts of water) to be applied to tile & fixed to surface, necessary protection of tiles after fixing.aGreen Kota Tile all exposed edges to be polished.1010Rm4454,450.00bVitrified tiles-1 basic cost Rs.140/sft + TaxQRORm4750.00cVitrified tiles-2 basic cost Rs. 120/sft + Tax100100Rm41541,500.00dVitrified tiles-2 basic cost Rs.90/sft + TaxQRORm3750.00eCeramic Tiles 1- Basic Cost - Rs.45/sft + TaxQRORm3500.00fCeramic Tiles 2- Basic Cost - Rs.65/sft + TaxQRORm3650.00B.01.05Cladding and Dadoing WorksB.01.05.1Providing, fixing & Laying "Under mentioned Tile / Slab" as dado as per design & manufacturer's instruction. Tiles to be fixied using neat cement past on to the wall surface to line and plumb as per the design indicated on the drawings. For Slab cladding the slabs shall be clad on the walls with a back filling of sand cement slurry in stages to ensure proper bonding throughout the surface of the slab. All cladding corners shall have birds beak joint duly polished as instructed by the Architect. Tile joints to be filled with water sealant (2mm wide grout) of approved color by architects. Laying & fixing details as suggested by the manufacturer to be followed.aGranite Cladding as per design - Basic Cost of Granite - Rs. 220 per sft. + Tax0Sqm4,1000.00bItalian Marble Cladding as per design - Basic Cost of Marble Rs. 450 Per sft + Tax.QROSqm8,2600.00cItalian Marble Cladding as per design - Basic Cost of Marble Rs. 600 Per sft + Tax.QROSqm10,5000.00dVitrified Tiles cladding as per design - Basic Cost of tile - Rs. 90 per Sft + Tax.QROSqm1,4650.00eVitrified Tiles cladding as per design - Basic Cost of tile - Rs. 120 per Sft + Tax.25QROSqm1,8460.00fCeramic Tiles cladding as per design - Basic Cost of tile - Rs. 35 per Sft + Tax.1515Sqm79011,850.00gCeramic Tiles cladding as per design - Basic Cost of tile - Rs. 65 per Sft + Tax.35QROSqm1,2050.00hClay Tiles cladding using Bal Endura grout. Clay tiles to be of size 3" x 9" as per selection of the Architect. Basic Cost of tiles Rs. 50 Per sft + Tax00Sqm1,3000.006,165B.01.05.2Providing, fixing & Laying Bizzaza or equivalent glass mosaic tile cladding on wall surfaces as per the manufacturer's specifications all complete including surface preparation, joint grouting and protection of the installation till handover as per design pattern and detail and selection of the architect. (Basic Rate of Rs. 145 per sft + Tax)QROSqm2,5000.00B.01.06Counter WorksB.01.06.1Counter - 700 deep made of 19mm thk marine ply finished with 19mm thk granite slab supported on MS brackets hung to wall at 800mm ht as per design and detail. Cost of counter to include for cutouts for basins, faucets etc. Counter shall have front facia in Granite as per detail. All exposed edges shall be polished to profile as shown on the drawings or as instructed by the Architects all complete. Basic Cost of Granite - Rs. 220 per sft + Tax00Rm4,9500.00B.01.06.2Counter - 700 deep same as B.01.06.1 above but with 12mm thk Corian top and Facia as per design and detail.QRORm15,250SUB TOTAL OF CIVIL WORKS CARRIED TO SUMMARY1,916,845Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Partitions and Panelling WorksB 02AIPL ESTIMATEGeneral Notes:1All hard wood wherever specified shall be treated with anti termite treatment and fire retardant paint.2All Timber sizes mentioned in the specifications shall be finished sizes after planing.3Rates quote for all partition items shall be for framework and skin only. All finishing items shall be measured and paid for separately under relevant items.4Contractor shall provide necessary protection for glass from scratches till handover. Rates to include for protection of glass with wrap film to avoid scratches and stains till handover or as instructed by the architects.5Particle board shall not be used for any items in the project. Wherever pre-laminated boards are specified the same shall be Pre-laminated MDF boards as per selected shades.6All frame work of partition shall be adequately braced to the true slab for proper stability.7Rates quoted for partitions / panelling shall be inclusive of making necessary cutouts for passing through of various services like ducts, raceways, pipes etc and for power, data and any other service outlets.8Rates quoted for partitions / panelling shall be inclusive of providing additional support members for housing of electrical, data or any other service outlet boxes. Rates shall also be inclusive of providing additional horizontal member at skirting level if required by design and no extra shall be payable for the same.9Rates for the partitions shall include for tissue / plastic sheet covering over the glass wool / rockwool insulation installed even if the same is not mentioned in the item specifications.10All free standing gypboard partitions or panelling shall be inclusive of proprietary corner protection of India Gypsum and shall be installed as per the manufacturer's instructions.11Wherever glass writing boards are specified, they shall be of 'Saint Gobbain' make color backed glass as per the approval of the architect.12Wherever partitions with gypsum skin meets existing wall surface, the cost to include for chicken mesh at the joints with necessary punning to ensure a crack free joint.13All panelling skins used any where for blocking external glazing where required as per design or any skin surface visible from the exterior of the building shall be painted black from the outside before installation.14Where Jeb Asia / Equivalent Sections are specified for the partitions the relevant sections shall be quoted for based on the thickness of the partitions. The product codes shall be confirmed with the architect before placing of the orders.SNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.02PARTITIONS AND PANELLING WORKSB.02.01Partition WorksB.02.01.1"SP-1" - Providing and fixing Solid partitions using 50x25 mm Aluminum stud Framework (1.2mm Thk Al sections) from floor to true slab and clad with 6mm Ply on both sides from floor to true slab. Cost of the partition to include for 50mm thk Glass wool / Rockwool Insulation 48Kg/m2 density infill for the complete area of the partition. Installation of the glass wool shall be protected with Tissue covering taped to the frame or plastic sheet taped to the frame on one side. Cost of the partition shall be inclusive of necessary additional bracing of the frames at the slab level for stability and making necessary cutouts for electrical / data and other service outlets and also for passing through ducts, cable trays and other service requirements. (Elevational area of the executed work shall be measured and paid for)775775Sqm1,8901,464,750B.02.01.2"SP-1a" - Providing and fixing Solid partitions same as SP-1 above but using 8mm thk ply skin on both sides.QROSqm2,800B.02.01.3"SP-2"- Fire rated partition - P/F 130mm thk gypboard partition wall (TYPE D) comprising of 70mm proprietary vertical studs, 2 layers of 15mm thk GRG (Glass Reinforced Gyp)board on each side, all as per manufacturer's specification.(Manufacturer - "INDIA GYPSUM") providing 2 hrs fire resistance barrier from floor to roof slab. Include 70mm thk rockwool insulation of grade specified by architect all from raw floor to bottom of ceiling slab (slab ht. approx 3600mm, verify @ site). Rate inclusive of GI corner beeds, hardwood scantelling, all requisite bracing to roof slab and other GI accessories finished with proprietary topcoat ready to receive paint). Include clear thick polythene vapour barrier fixed to the warm side of gyp board.7575Sqm2,000150,000B.02.01.4"SP-3"- Gypsum Partition Wall - P/F 94mm thk gypboard partition wall comprising of 70mm proprietary vertical studs, 1 layer of 12mm thk Gypboard on each side, all as per manufacturer's specification.(Manufacturer - "INDIA GYPSUM") from floor to roof slab. Include 70mm thk rockwool insulation of grade specified by architect all from raw floor to bottom of ceiling slab (slab ht. approx 3600mm, verify @ site). Rate inclusive of GI corner beeds, hardwood scantelling, all requisite bracing to roof slab and other GI accessories finished with proprietary topcoat ready to receive paint). Include clear thick polythene vapour barrier fixed to the warm side of gyp board.IGL specs partitionQROSqm1,800B.02.01.5"GP-1" - P/F glazed partition comprising of 12mm thk tempered edge polished glass to be fixed on U channel (MS powder coated 12mm x 19mm) in floor with normal rubber gasket. Cost of framework to hold glass above false ceiling will be measured seperately. cost to include openable teak wood beading at false ceiling level to hold glass. Also include cost of 3M crystalline etching film (35% area) of glass. size of beading shall be 12mm thk x 35mm finished with paint to match ceiling color. Size of glass panel to be minimum 1000mm Length. Cost to include filling joints with silicon sealant where ever applicable. Glass height upto 2500 / 2650 mm based on location in single piece.00Sqm4,0000B.02.01.6"GP-2" - P/F glazed partition as above but using Jeb Asia or equivalent sections on all sides of the glazed partition. (Using Sections SAP 44,45 and 47 as per manufacturer's details.170170Sqm3,825650,250B.02.01.7"SP-4" - P/F Partitions above ceiling same as SP-1 above but using one layer of Gypboard on both sides instead of Ply.5050Sqm1,53576,750B.02.01.8"SP-5" - P/F Solid Partitions above as shaft divider same as SP-1 above but with 10mm thk Bison board or equivalent Cement boards on both sidesQROSqm2,800B.02.01.9"SFP-1" Sliding & folding partition - Supply & Installation of Dorma operable wall system single track with Dorma series panel or equivalent, standard trim & center tracking. The wall system shall have retractable top & bottom seals (openable). Panel size shall be as per approved shop drawing & have an accoustic rating of 52 STC. Track shall be natural anodised, seals - grey, panel frame powder coated & panel surface fabric with foam backing or ceramic white board as per details . Rate to include all applicable taxes, unstuffing, hoisting, installing, protecting, cleaning, accessories & supports above false ceiling to hold track, partition above this wall system, partition above false ceiling, glass wool infill in partition above false ceiling etc complete. Partition above false ceiling shall be made with MS frame work 50 x 50 finished with 19mm thk ply on both sides & finished with 12mm htk gyp borad on ply (on both sides). Gyp board shall be ready to receive paint.00Sqm29,7000B.02.01.10"SFP-2" Sliding & folding partition - Supply & Installation of Dorma operable wall system with 12mm thk toughened glass panels on proprietary fixing elements.0Sqm56,0000B.02.01.11"FP-1" Providing and fixing in place Feature Wall partition 200mm thk to be fabricated with Al frame work and 12mm thk ply on both sides. All edges shall also be finished with 12mm thk Ply. Partition to be erected upto 2100 mm height and shall be free standing. Adequate additional bracing and fixity to the floor to be provided for.77Sqm5,60039,200B.02.01.12"RP-1" Providing and fixing in place Relocatable Glazed partitions to be erected from floor to False celing. Partitions shall be proprietary partitions with 10mm toughened glass. (Intact relocatable partitions or equivalent make as per Architect's approval.)00Sqm7,5000B.02.01.13Providing and fixing at locations as indicated on the drawings, proprietary Jeb Asia, Aerofoil metal anodized sections complete as per the manufacturers specifications and details.SAP 80 + 854545Rm4,500202,500.00SAP 0181515Rm4,50067,500.00B.02.02Panelling WorksB.02.02.1"P1" - P/F average 62.5 mm thk panelling comprising of 50x25mm aluminum stud (1.2mm thk) @ 600mm x 600mm distance and one base layer of 12.5mm thk gypboard on one sides. The layer of gypsum will stop at false ceiling (min 75 above level of ceiling) and stud shall continue to true slab as required for anchorage. Rate inclusive of GI corner beeds, hardwood scantelling and other GI accessories finished with proprietary topcoat ready to receive paint).; contractor to provide requisite bracing to reinforce paneling. Rate not to include supplying & installing skirting. (Column Cladding on all floors)275275Sqm942259,050B.02.02.2"P2" - P/F Panelling framework only out of 50x25 mm aluminum box section in line level and plumb ready to receive skin at locations indicated on the drawings or as instructed by the architect, all complete. (Cost to be for providing and fixing framework only)5050Sqm79039,500B.02.02.3P/F Panelling skin as mentioned below over framework / partitions / walls etc. as indicated on the drawings and details or as per the instructions of the Architect, all complete. (Cost to be for providing and fixing skin only)a4mm thk MDF skin55Sqm4202,100b4mm thk Ply skin55Sqm3951,975c6mm thk MDF skin1515Sqm5157,725d6mm thk Ply skin1515Sqm4957,425e8mm thk Ply skin2525Sqm54513,625f12mm thk Ply skin2525Sqm66516,625g12mm thk MDF skin2525Sqm69517,375h19mm thk Ply skin2525Sqm86021,500i19mm thk Ply skin (marine Ply)55Sqm1,0405,200B.02.02.4P/F Panelling finish as mentioned below over framework / partitions / walls etc. as indicated on the drawings and details or as per the instructions of the Architect, all complete. (Cost to be for providing and fixing finish as per specs only)a12.5mm Gypboard skin over exisitng partition / frame work duly finished with proprietary top coat as per manufacturer specification ready to receive paint / wall paper or other finish.12001200Sqm286343,200b4mm veneer panelling out of selected approved veneer duly melamine polished to approval. The cost of veneer panelling to be inclusive of 8mm ply backing to the veneer. (Basic Cost of veneer Rs. 35 Per sft + tax)QROSqm1,875cSame as item B.02.01.4-b above but with basic cost of Veneer as Rs. 55 + Tax7070Sqm1,825127,750d1mm Laminate panelling as per selected shade of laminate. Cost to be for only laminate supply and fixng.5050Sqm48024,000eLacquer back Glass pannelling - 6mm thk Glass panelling using Saint gobain lacquer back glass. Laccquer coating to be white color and the glass used to be extra clear glass. (for writing glass white boards). Cost to be inclusive of 6mm ply backing to glass4040Sqm5,700228,000fColor back Glass pannelling - 6mm thk Glass panelling using Saint gobain color back glass. Laccquer coating to be chosen approved color and the glass used to be extra clear glass. (for oantry are rear panelling).1212Sqm4,00048,000gEcho Panel - panelling with echo panels for command center walls over existing partition. (basic cost 500 per sft)7575Sqm5,200390,000.00B.02.02.5Fabric paneling - Providing and fixing Blow Plast Proprietary panelling system which shall comprise of powder coated MS base framework and fabric tiles. (Basic cost of fabric shall be Rs 350 per meter). Salotex board shall have TW lipping beading before the fixing of the fabric to achieve a neat and straight edge after wrapping.7575Sqm3,800285,000B.02.02.6Fabric paneling - Providing and fixing Same as above but using Wall Tract Proprietary system0Sqm3,6500B.02.02.7Fabric paneling - Providing and fixing soft board panelling with Salotex board having TW lipping beading before the fixing of the fabric to achieve a neat and straight edge after wrapping. (Basic cost of fabric shall be Rs 350 per meter)00Sqm1,3860B.02.02.8Providing and fixng MDF panels to receive Graphics on both sides of Glass partitions with counter sunk studs connecting both the MDF panels through the glass. All complete ready to receive Graphics. Size of panels 2400 x 1050 mm. approx. (Panels on both sides of the glass shall be measured and paid for separately)00Sqm12,5000B.02.02.9Providing and fixing MDF panels ready to receive paint 12mm thk over the spandrel panels of the structural glazing. The MDF panels to be cut to size of the structural glazing frame c/c sizes and fixed on the the frames with double sided 3M tape / or screwed as instructed all complete as approved. Panels to be painted Grey / Black on the outside before fixing00Sqm13,4000B.02.02.10Windows cill bund cladding 225mm high boxing at skirting level @ general office area consisting of 1mm thk laminate on 19mm thk marine ply. Edge to be finished with TW beading beading as per detail all duly melamine polished as per architects approval. Vertical facia on the outer side of cill i.e on external glazing side shall be made with 19mm thk marine ply & finished with exterior Grey paint. Include silicon @ junction of wood / glass.0Rm1,8000B.02.02.11Providing and Fixing 100mm High Skirting as per the following specificationsaP/F 12 X 100mm high melamine polished Wood Veneer skirting - as per details and instructions of the architect. Cost of scantling & support should not be included in cost of skirting. Skirting to be stuck with silicon. Cost to include 8mm Ply backing to veneer.0Rm4650bP/F same as above but using 12mm thk 100 mm high timber section as per selection of the Architect all complete and duly melamine polished to approval.0Rm4750cP/F same as above but using 100 mm high Aluminum skirting of JEB / Builder Box or equivalent as per selection of the Architect all complete inclusive of all corner filler pieces and other applicable accessories. Cost of skirting to be inclusive of 12 mm ply backing.700700Rm540378,000B.02.02.12Providing and Fixing Chair Rail panel of 300 mm height to be finished in approved veneer on 8 mm ply backing as per design at detail complete and duly finished in melamine polish as approved.0Rm9000B.02.02.13Providing and fixing SS edge capping "U" shaped in profile for partition edges at locations like dry pantry, printer stations etc. of the following sizesa150mm wide and 50mm deep0Rm1,7500b50mm wide and 50mm deep0Rm1,2500B.02.02.14Providing and fixing 6mm thk Corian Edge trim for partition edges at locations like dry pantry, printer stations etc. of the following sizes0Rm0a200mm wide1515Rm1,48522,275b50mm wide1010Rm4204,200c100mm wide (For Skirting)3030Rm74022,200B.02.02.15Providing and fixing PVC Corner Guards of Acrovyn make (imported) as per manufacturer's specifications at locations as indicated on the drawings and instructions of the architect.8080Rm24519,600Sample to be shown and approved.B.02.02.16Providing and fixing PVC Corner Guards same as above but using SS L angle of 40mm x 40mmQRORm800SUB TOTAL OF PARTITIONS AND PANELLING CARRIED TO SUMMARY4,935,275Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Doors and WindowsB 03AIPL ESTIMATEGeneral Notes:1All Door Frames if free standing shall be braced above the ceiling with additional supports as required. All timber door frames shall be grouted in the floor for additional stability.2Veneer for all doors shall be as per the selection of the Architect.3In case of timber frames, the frames shall be stained to match the approved polish shade of the veneer. All section sizes mentioned shall be finished sizes of timber.4Contractor shall provide necessary protection for glass doors from scratches till handover. Rates to include for protection of glass with wrap film to avoid scratches and stains till handover or as instructed by the architects.5All flush doors shall have 12mm thk lipping on all four sides stained to match the veneer polish6All Hard ware used for the doors shall as per the list of approved makes only7Refer Door window schedule for the various types of door8Contractor shall provide samples of all hardware for the Architect's approval before ordering of the same.9All doors used for areas like Pantry, Janitor, Toilets and other wet areas shall be BWP grade.10All Door closures shall be as per the manufacturer's recommendation based on the size and the weight of the doors.11For All doors on floor spring which have access control, the floor spring shall be 130 degree locking type.SNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.03DOORS AND WINDOWSB.03.01Doors and WindowsB.02.01.1DG1 (2000 x 2500) Double Glazed Door shutter (1000mm wide each shutter). Shutter made with 12 mm thk. Clear float tempered glass with mirror polished edges, 3M frosted film 33% (crystal quality). Also including 100x40mm thk teakwood top & bottom rails The rate should be inclusive of all hardware viz floor spring, etc complete including SS handle (1200 mm ht & thickness as per manufacturer recommendation) for both leaves of shutter internal & externall. Doors shall have necessary provisions for Access control as required.11Nos82,50082,500.00B.02.01.2DG2 (1100 x 2450) Door (Single shutter of 1100mm wide x 2450 on patch fitting - DORMA) / Shutter made with 12 mm thk. Clear float tempered glass with mirror polished edges, 3M frosted film 33% (crystal quality) complete as approved by architect. The rate should be inclusive of all hardware viz. Patch Set, floor spring etc.1200mm SS handle, complete with requisite holes for lock. (For access control doors the Floor spring shall be 130 degree locking type)66Nos42,500255,000.00B.02.01.3D1 (1000 x 2450) flush door shutter (32mm thk) cladded on both sides with melamine polished approved veneer. Door to have 4mm x 4mm groove in veneer as per design as approved by architect. The rate should be inclusive of all hardware complete including exposed door closure, locks,hinges & handle. Door to have 450mm long D handle and independent lock as shown on drawings.55Nos17,32586,625.00B.02.01.4D2 (1000 x 2450) flush door shutter (32mm thk) cladded on both sides with melamine polished approved veneer same as above but with vision panel of 200 mm x 1800mm1515Nos18,075271,125.00B.02.01.5D2-a Same as D2 above but with one side finished in Veneer and the other side finished in Laminate of approved shade and color00Nos20,0000.00B.02.01.6D3 Same as D2 above but of size 900mm x 2450mm00Nos17,0000.00B.02.01.7D4 (1650mm x 2450 mm) Providing and fixing Double Leaf Flush door of 32mm thk clad with veneer on both sides and finished in melamine polish as approved. Door to be fabricated with twin shutters (one of 1100mm width and another panel of 450 mm width). Both shutters shall be provided with 450mm long SS 'D' handle as per the selection of the Architect. The 1100mm wide shutter shall be provided with 200 x 1800mm vision panel as shown on the drawings. 450mm shutter shall be provided with concealed tower bolt. Door shall be inclusive of all necessary hardware like ball bearing hinges, exposed door closure, locks etc as per the selection of the Architect.22Nos31,18862,376.00B.02.01.8FD1 of size 1650W x 2450H(Fire rated Door 120 minutes size & no of shutters mentioned below) with vision panel (900Hx200W) with wired glass, access controlled door of non-metallic, 50mm thk asbestos free composite fire & smoke check shutters comprising of two non combustible boards 12mm thk sandwiching 20mm thk fire resistant filler, of 2 hour fire resistance rating conforming to BS:476 part-22, IS:3614 suitable for mounting on MS frame as recommended by Manufacturer, 2 hr. fire rated vision glass panel, with heat activated intumescent fire seal strips of size 12x4mm fixed on all three sides except the bottom and the frames. Shutter to be mounted with DORMA SS fire rated hinges with necessary screws and one coat of anti-termite fire resistant primer. Rate shall be inclusive of hardware complete with requisite holes for magnetic lock, heavy duty exposed door closure (dorma). Shutter to be claddded with 4mm thk veneer externally & laminate internally as approved. Cost to be inclusive of MS Frame as per approved manufacturer's specifications.11Nos54,45554,455.00Same as above but for single shutter of size 1100 x 2400 mm size11Nos47,50047,500.00B.02.01.9Providing and fixing Door frames of the following sizes made out of First quality Teak wood and finished in Melamine polish to approval of the architect. All door frames shall be grouted in the floor to the extent of 2" for stability. Doors to have necessary rebates as per the thickness of the doors. All doors in civil walls shall include 3 nos of MS hold fasts on each side.Cost to be quoted per Rm length of frameQRORm2,500Size of timber section to ne 100 x 75B.02.01.10Providing and fixing Door Frames of Extruded Aluminum sections of JEB / Builder Box of equivalent of 105mm x 50mm with Anodised finish as per the approval of the Architect.150150Rm2,770415,500.00B.02.01.11Providing and fixing Portals made of 19mm Ply boxing of size 200 x 300 mm and clad from ceiling to floor with 6mm thk Corian on front and back side and the width to be finished in Novafine paint of approved shade and color1010Rm5,15051,500.00SUB TOTAL OF DOORS AND WINDOWS CARRIED TO SUMMARY1,326,581Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Ceiling and Flooring WorksB 04AIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.04CEILING AND FLOORINGB.04.01Ceiling and Allied WorksB.04.01.1Gypsum board suspended ceiling with proprietary GI steel suspension system as recommended by mfr (INDIA GYPSUM) frames & accessories, 12.5mm thick gyp board sheets, screws, taping, joint grout finished with priming top coat & plastic emulsion paint (base putty & three coats) of color as per architects approval & manufacturer's instructions. The rate shall be inclusive of making cutout for light fixtures, diffusers, grills etc and making good 12x12mm groove at all junctions of gyp bd ceiling w/ walls. Include proprietary GI corner bead as/detail and architect's approval. Note that all exposed vertical surfaces with this same specifications (irrespective of its height) shall be accounted in this item for measurements except cove / pelmet for window blinds / pelmet trough for AV screen.450450Sqm614276,300B.04.01.2Making 200 x 300mm cove as/detail in gypboard and POP including plastic emulsion paint matching with gyp ceiling as per architect's approval.. The rate shall be inclusive of necessary framework, making cutout for light fixtures, bulkheads, internal & external vertical facia etc. complete. Cove section includes exposed L-Shaped gyp work.6565Rm24716,055.00B.04.01.3Window pelmets (200 x 200) in 19mm thk marine ply. Board with hardwood lipping, and fixed to ceiling with metal framing complete including painting (three coats with base primer & putty) with plastic emulsion paint. Paint to match shade of false ceiling. Rate to include paint. (Rate to include necessary extra hardwood frame where ever required & silicon joint where marine ply board meets window, glass partition or periphery curtain glass) & one layer of gyp board cover. Pelmet to be fixed at false ceiling level.110110Rm44548,950.00B.04.01.4AV trough 2800W x 200H x 200W internal finished size made of 19mm thk ply finished internally with . Trough to match with false ceiling level. Contractor to ensure requisite bracing & support to soffit of slab is maintained. Pelmet to be braced enough to carry 50 KG weight of screen1010Rm6456,450.00B.04.01.5Rafters - Providing and installing rafters in aluminum "U" shaped sections of size 100mm x 75mm in ceiling to be fixed as shown on the detail drawings. The cost of rafter to include Ply boxing at either end to hold the rafter in place as per detail drawings and as per the instructions of the Architect. Rafter shall be powdercoated / Anodized to the approval of the Architect. Cost to include for additional suspension wires to hold the rafter in case of longer lengths.00Rm1,5000.00B.04.02Flooring WorksB.04.02.1P/L Anti-Static conductive Vinyl flooring (2mm thk) of LG / Armstrong make in tile or roll form as per approval as main area with heat welded copper seams laid as per manufacturer's specifications to architect's approval. The rate shall be inclusive of necessary preparation, cleaning, protection, earthing point, making floor anti-static etc. complete. Note: only laid quatity shall be measured for payment.Labs, Hub, etc4040Sqm1,71768,680.00B.04.02.2P/L conductive flooring (2mm thk) of Tarkett TORO EL / Equivalent make (tile of size 600 x 600mm) as main area with heat welded copper seams laid as per manufacturer's specifications to architect's approval. The rate shall be inclusive of necessary preparation, cleaning, protection, earthing point, making floor anti-static etc. complete. Note: only laid quatity shall be measured for payment.Labs, Hub, etcQROSqm1,385B.04.02.3P/F 3.3mm thk PVC vinyl flooring @ stores, utility room as per architect's approvals & manufacturers instruction. Only laid quantity to be measured for payments. LG basic price 60/sft to be considered.Store rooms, elec rooms etc.4545Sqm74033,300.00B.04.02.3P/L Vinyl flooring Sports Flooring / equivalent PVC vinyl flooring in roll (1500mm wide) @ break outs (above mosaic flooring) with cushion backing as per architects approvals & manufacturer's instructions. This also includes providing the seamless joints with proper joint treatment using matching shade PVC trims with soft welding as per manufacturers specifications and as approved by the Architects. Cost of mosaic flooring not to be included in this item.QROSqm7,400B.04.02.3Providing and fixing transition profiles "Gradus floor trims - adjustable" at junction of various types of floor (joint of carpet with hard floor, joint of carpet with wooden floor, joint of hard floor with wooden floor etc) wherever necessary as per architects approval.2525Rm1,38534,625.00B.04.02.3Providing and fixing transition profiles in SS at locations where flooring trasition (joint of carpet with hard floor, joint of carpet with wooden floor, joint of hard floor with wooden floor etc) wherever necessary as per architects approval.00Rm6500.00B.04.02.4Steps for False / Access flooring - Providing & fixing in place ramp (sloped) made of 25mm thk marine ply supported on wooden pedstals made out of 25mm thk marine ply. The surface of ramp shall be ready to receive carpet. Cost to include complete finishing of ramp including vertical facia. Cost shall be computed same if steps are to be fabricated33Sqm3,46510,395.00B.04.02.5P/F SS L shaped step cover over ply box. SS angle shall be 75mm x 75 mm corner guards over the step edge.55Rm6453,225.00B.04.02.6P/F 12mm thk ply emulsion paint finished trap-doors of size as required with TW frame around the same as per details in ceiling as per site conditions55Sqm1,9809,900.00B.04.02.7P/F Expansion joint Trim on floor wall and ceiling of Gradus or equivalent make as per manufacturer's specifications and details0Rm1,2600.00SUB TOTAL OF CEILING AND FLOORING CARRIED TO SUMMARY484,360Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Built In FurnitureB 05AIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.05BUILT IN FURNITUREB.05.1Posters (750 x 1200) - It shall be made with one layer of 12mm MDF and one Layer of 4mm sun board fixed over TW sections mentioned below. Art work to be given by client. The posters shall be stuck with 100 x 100 x 450 TW wood section (stained to match color scheme) with 3m double sided tape. The TW wood section shall be screwed to partition. Poster panels shall have 25mm wide Aluminum trim around the panels88Nos3,46527,720B.05.2Overhead Storage Units 400 Deep including lighting pelmet, with carcass and shutters made out of 19 thk comm. Ply. Shutters to be finished with 1mm thick approved laminate outside and balancing laminated on inside. Hardware- Lock sets, self-closing hinges, spring loaded shutter latch inside, all cabinet hardware to be kitch / dorset or equivalent, complete as per architect's approval.99Sqm6,68560,165B.05.3Over Head storage same as 2 above but finished in approved veneer from the outside and balancing laminate from inside.QROSqm9,000B.05.4Counter - 700 deep made of 19mm thk comm b/b finished with 1mm thk laminate with laminated panelling below counter. Rate to be inclusive of one vertical support below counter every 1500 mm finished with both sides in laminate.33Rm4,45513,365B.05.5Counter - 700 deep made of 19mm thk comm b/b finished with 4mm thk veneer with veneer panelling below counter. Edge of counter to be finished with 19mm x 35mm matching wood beading. Inclusive of vertical supports same as above.33Rm7,50022,500B.05.6Providing & fixing Storages and DB panel cabinets comprising of carcass and shutters constructed from 19mm thk. comm. board finished in 4mm thk. melamine polished approved veneer, balancing laminate inside and 4mm thk. approved veneer finishes in trims.The rate should be inclusive of necessary hardware- SS cabinet handles , Lock sets, self-closing hinges, spring loaded shutter latch inside, all cabinet hardware to be or equivalent, complete as per architect's approval. Rate to include 150 X 300 mm wide powder coated aluminium grills. (Note - contractor to coordinate w/ architect & electricals/networking vendor prior to fabrication of shutters for appropriate sizes).00Sqm5,1500B.05.7P/F full height / Low Height storages of size 450d at locations indicated on the drawings or as instructed by the Architect with carcass and shutters of 19thk commercial ply with 1mm thk balancing laminate inside. Rate to be inclusive of all necessary hardware - , locksets, self closing hinges, spring loaded shutter latch inside, all cabinet hardware to be as per approved list of makes complete as per architects approval.TYPE A finished with 1mm thick approved laminate on outside.4040Sqm6,140245,600TYPE B finished with matt melamine polished 4mm thick approved veneer1010Sqm7,13071,300Type C - open shelves finished with 1mm laminate on all surfaces & 12mm x 25mm polished matching wood beading on all exposed edges.88Sqm4,70037,600B.05.7P/F Low height undercounter storage unit with carcass and shutters with 19mm thick comm ply finished with 4mm thick veneer. counter top to be finished with 19mm approved Granite, with the edge of the counter to be 40mm thk.All internal surfaces to finished in balancing laminate as approved. Include 50 high skirting above the counter finished with veneer. Undercounter storage to have a adjustable shelf inside at 380mm level (internal clear) to be finished with laminate on both sides. Rate to be inclusive of all necessary hardware - SS cabinet handles 100mm long, locksets, self closing hinges, spring loaded shutter latch inside, all cabinet hardware to be as per architects approval. Cost to include for cutouts on the top as required700 Wide Storage88Rm7,57560,600450 Wide Storage00Rm7,7500B.05.8P/f Low Height under counter storage same as above but using 19mm marine ply for the caracass and shutters. Cost of counter to include for cutouts on top as requried. For 700 Wide counter onlyQRORm5,445B.05.8P/F magazine rack in Reception (800 x 1800mm) made of '12mm thk clear imported Acrylic sheet'. Rate to include 12mm thk clear acrylic base sheet with magazine shelves made of 6mm thk acrylic finished with SS studs on wall / partition. Refer detail drawing of magazine rack22Sqm4,9509,900B.05.9Veneer ledge in meeting room - 300mm deep 50mm thk ledge made out of 15mm thk comm b/b finished with approved veneer and melamine polish as approved.00Rm1,3350B.05.10Veneer ledge in meeting room - 200mm deep 50mm thk ledge made out of 15mm thk comm b/b finished with approved veneer and melamine polish as approved.00Rm1,2400B.05.11P/F Full height Mirror panelling in Toilets or other areas as indicated comprising of 6mm thk imported belgium mirror or equivalent In modules of 900X1800 , fixed on to 6mm back ply with 12mmX50mm wooden beading stained to architect's approval.00Sqm1,8800B.05.12Providing & fixing mirrors @ toilets as per sizes indicated with 8mm thk float glass with mirror polish in the rear side as per detail fixed by 3M double-sided tapes with 19mm thk ply backing. Provision for light pelmet to be made as per design detail.55Sqm2,12510,625SUB TOTAL OF BUILT IN FURNITURE CARRIED TO SUMMARY559,375.00Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - Loose FurnitureB 06AIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.06LOOSE FURNITUREB.06.1Reception Table - Providing and placing Reception table to be fabricated out of 19mm commercial ply as per design and detail completely finished in approved veneer and melamine polish inclusive of 2 nos pedestals of under mentioned size as per design detail in Drawing. Refer Detail drawing of reception table.Size of Table 3600mmL x 750mmD x 1100mmH. Table to have second level top of Granite as per Architect's choiceBasic cost of granite 220 per sft11Nos142,529142,529B.06.2Security Table of size 1800 x 600 D x 1050 H completely finished in laminate of approved shade and color as per design and detail.Table to have second level top in Granite of approved shade and color.00Nos19,8000B.06.3900w x 2100hx 600d Slotted Angle Racks industrial type (Godrej - REGULAR TYPE).QRONos8,500B.06.4Locker - providing & fixing in place lockers of size 300W x 400H x 600D. Carcass & shutters to be made of 19mm thk ply finished with laminate internally & externally. Rate to include complete hardware lock for each locker.7575Sqm7,425556,875B.06.5Providing and Fixing "Alkosign or equivalent" - Astra series magnetic Writing Board. Rate shall include starter kit, fixing etc complete of the undermentioned sizes. Include removal of aluminum beading. Edges to be finished with Teak wood beading of size 40w x 19d.a 2400 x 120000Nos14,4000b 1800 x 1200QRONos10,800c 1200 x 90000Nos5,4000B.06.6P/F 3M BRAND heavy duty NOMAD MATS Size : BASED ON ACTUAL REQUIREMENT PER SITE CONDITION55Sqm3,66518,325B.06.7P/F Notice / soft boards comprising of 12mm thk pinnable salotex board over 12mm comm. Ply w/ 25x50mm melamine polished maple surround trims. Fabric wrapped on cellotex board on 3mm thk foam backing. Salotex boards to have Al. U channel around its edges. (B.R. of fabric at Rs. 400/- Rm)00Sqm2,5000B.06.7Providing Wastebins of size 300 dia, 400 high perforated M.S. Powder coated as per design and details.77Nos7405,1800B.06.8P/F key chest of size 1000 x 1500 made of 19mm thk ply finished with laminate on all sides. Cost to include u-hooks to hold keys.Key chest to be made as drawer units with pull outs for the key hanging slots on telescopic chanels.22Nos9,90019,800B.06.9Providing & fixing on glass "3M" Sun control film as per manufaturer's instruction.QROSqm2,000B.06.10Providing & fixing in place wooden box frame fabricated out of sal wood / ply above floor junction box. The height of wooden box to vary between 25 to 45 mm as per site condition such that wooden box when placed over junction box shall match with ht / level of screed. Size of box 450 x 4505050Nos50025,000B.05.11Pen stand for writing board - to be fixed on writing board / partition - fabricated of SS sheet with holes to keep marker 7 space for duster. Size 200 x 100mm66Nos4452,670B.05.12Providing and Installing SS Plate 2mm thk of size 200 x 300 at locations indicated on the drawings to mount Access Control readers. Cost to include making necessary cutouts to draw cables as required.1414Nos4005,600SUB TOTAL OF LOOSE FURNITURE CARRIED TO SUMMARY775,979.00Item of WorkGENERAL CONSTRUCTION WORKSPART BBill of Quantities for General Construction Works - FinishesB 07AIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALB.07FINISHESB.07.1Paint on walls and gypboard/POP ceiling including surface preparation, primer coats, levelling patti and minimum 3 coats of brush and roller finish.Type A - Normal plastic emulsion Paint750750Sqm11888,500Type B - Dark colored Accent Paint with a base coat of oil paint.2020Sqm1653,300Type C - Novafine paint for partition / Wall20002000Sqm420840,000Type D - Duco paint00Sqm7650Type E - Black paint on soffit of ceiling/ pelmet fascia towards glazing7575Sqm1209,000Type E - Textured Paint or accent paints of Armour Coat as per selection. (Basic range of 150 per sft)00Sqm1,8250B.07.2p/f silicone sealant at all areas where partitions abutt external glass wall..1010Rm80800B.06.3Providing & applying in position 3M safety film on glazing.QROSqm2,150B.06.4Providing & applying in position 3M crystal film on glazing. Or Colored Transparent film of Llumar or equivalent make00Sqm2,3500B.06.6Wall Papers - Supplying & laying wall papers on walls / partitions / RCC columns after making the subfloor neat & clean. Wall paper's basic cost of wall paper shall be 90/sft. Wall papers shall be vinyl backed and as per architect's selection.100100Sqm1,150115,000B.06.7Digital art by 3M - Solvent printed (water proof ink) art work on opaque vinyl to be stuck directly on wall. Art work to be given by client.5555Sqm5,000275,000B.06.9Theme Panelling - Providing and fixing theme panelling at locations as indicated on the drawings or as instructed by the Archtiect using the following materials.aClay Tile Cladding - Providing and fixing clay tiles as per the selection of the architect at locations as indicated on the drawings using Bal Endura Grout to fix tiles on the wall surface. Basic cost of Tiles Rs. 60 per sft00Sqm1,4500bWooden Floor Panel Cladding - Providing and wooden floor panels as per the selection of the architect at locations as indicated on the drawings fixed on base 12mm ply as theme panels. (Infloor or equivalent) Basic Cost of Wooden Floor Rs. 150 per sft4545Sqm2,425109,125c3M Vinly Film - Providing and Fixing '3M' DI-NOC range of films over finished GYP surface at locations indicated on the drawings. Basic Cost of Vinyl Film Rs. 225 per Sft00Sqm3,5000SUB TOTAL OF FINISHES CARRIED TO SUMMARY1,440,725Item of WorkGENERAL CONSTRUCTION WORKSPART CBill of Quantities for General Construction Works - Plumbing and Rest Room AccessoriesAIPL ESTIMATESNODescription of WorksProduct CodeUnitsRate (Rupees)Amount (Rupees)RemarksFloorTOTALCPLUMBING AND REST ROOM ACCESSORIESC.01Providing and installing SS Sink with drain board for wet pantry inclusive of necessary support brackets as per manufacturer's recommendations, CP stop cock of Jaguar, CP bottle trap with necessacr coupling and connections, inlet connector pipe, and Sink cock of Jaguar all complete as per the instructions of the Archtiect.00Nos16,2000C.02Providing and installing CP Coat hooks in WCs of Jaguar make as per the selection of the Architect.00Nos9000C.03Providing and Installing Toilet paper holders of Euronics make as per the selection of the Archtiect.00Nos3,0000C.04Providing and Installing Paper Towel dispenser of Euronics as per selection of the Archtiect.00Nos6,5000C.05Providing and Installing Hand Dryer of Euronics or equivalent approved make as per selection (Model EH 01 S)00Nos16,5000C.06Providing and Installing SS Grab Bars of 600 mm length in Handicapped toilets of Jaguar make as approved00Nos2,500C.07Providing and Installing SS Soap Dispenser of Euronics make or equivalent (Model No. KSD 01)00Nos8,50000C.08Providing and Installing Wall hung WC with cistern with all required accessories and plumbing connections like angle cock, flexible connector pipe to cistern, all required connections from cistern to WC and required trap connections to Builder provided connections all complete as per detail drawings and instructions of the Architects. (Hindware - 20028 Constellation Series)00Nos12,0000C.09Providing and Installing high back urinals of Hindware make inclusive of all required plumbing accessories like CP connectors, battery operated urinal sensor, bottle trap, and all required waste line extensions to connect to the builder provided outlets all complete as per detail drawings and the instructions of the Archtitect. (Hindware - Model No. 96002 Olympus)00Nos13,5000C.10Providing and Installing counter mounted wash basins of Tulip range of Hindware inclusive of all plumbing connections like CP inlet connectors, Angle cocks, bottle traps etc. Cost of installing wash basing to be inclusive of installing Auto tap of Jaguar make. ( Tulip - Hindware - 10071 and Jaguar Auto Tap - 51011)00Nos18,0000SUB TOTAL OF PLUMBING AND TOILET ACCESSORIES CARRIED TO SUMMARY0

03 Raised floorRAISED FLOORING BOQDescriptionRemarksQtyUnitsRateAmountRAISED FLOORING FOR UPS, SERVER RMTOTAL 135 sqm10%wastage 14sqmGRAND TOTAL 149 Sqm149Sqm1605Sqft200.00321,000.00Total for RAISED FLOORING321,000.00RAISED FLOORING FOR LABTOTAL 125 sqm10%wastage 13 sqmGRAND TOTAL 138 Sqm138Sqm1485Sqft200.00297,000.00Total for RAISED FLOORING297,000.00Grand Total618,000.00

&L&11MICROSOFT/JLL/AIPL&R&11Page&P of Page&N

04 Electrical WorksELECTRICAL WORKS BOQSL.DESCRIPTIONUNITQTY.RATEAMOUNTNO.(Rs.)(Rs.)ACIRCUIT CUM POINT WIRING1Wiring for switch board controlled light points with 3Rx2.5mm upto first light point & for loop points 3Rx1.5 sq.mm FRLS PVC insulated copper sheathed cable in 2mm thick 25 mm dia. FRLS PVC, white color conduit along with all fixing accerrories i.e. bend with cover,coupler T-joint & junction boxes witha.One point controlled by one no. 6 amps switchSets2065013,000b.Two points controlled by one no. 6 amps switchSets3075022,500c.Three points controlled by one no. 6 amps switchSets5685047,600d.Four points controlled by one no. 6 amps switchSets551,00055,000e.Five points controlled by one no. 6 amps switchSets261,10028,600f.Six points controlled by one no. 16 amps switchSets151,25018,750g.Seven points controlled by one no.16 amps switchSets181,40025,200h.Eight points controlled by one no. 16 amps switchSets21,6003,200i.Nine points controlled by one no. 16 amps switch.Sets01,9000j.Ten points controlled by one no. 16 amps switch.Sets52,30011,5002Wiring for switch board cum sensor controlled light points with 2.5 /1.5 sq.mm FRLS PVC insulated copper wire and earthing with 1.5 sq.mm insulated copper wire in medium duty FRLS PVC conduit, including providing of modular switch at switch board & modulaaOne point controlled by one no. 6 amps switch & sensor.Nos.Rate476b.Two point controlled by one no. 6 amps switch & sensor.Nos.Rate6893Wiring for MCB controlled light points with 2.5 /1.5 sq.mm FRLS PVC insulated copper wire and earthing with 1.5 sq.mm insulated copper wire in medium duty FRLS PVC conduit, including providing of modular switch at switch board & modular sockets near exhaut fan with modular plates and GI Boxes.MCB's prices should not be inclusive with this item,but considered somewhere in BOQ.aOne point controlled by one no. 6 amps, 10KA, C-Curve MCBNos.26501,300b.Two point controlled by one no. 6 amps, 10KA, C-Curve MCBNos.67504,500c.Three point controlled by one no. 6 amps, 10KA, C-Curve MCBNos.090003Wiring for 1 no. 250 V, 1 phase, 6 A (5 pin, Round/flat) universal Raw switched socket outlet with 3Rx2.5 sq.mm FRLS PVC insulated copper flexible sheathed cable in 16SWG 25mm dia MS rigid / G.I flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of MS flexible conduit, as requires, including providing & fixing of 6amps modular switched socket complete with modular plate and suitable size of GI box complete. FOR PEST REPALLENT SYSTEMSSetsRate7504Wiring for 1 no. 250 V, 1 phase, 6 A (5 pin, round/flat) UPS universal unswitched socket outlet with 3Rx2.5 sqmm FRLS PVC insulated copper flexible sheathed cable in 2mm thock 25mm dia FRLS PVC rigid/flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of PVC flexible conduit, necessary bracket for vertical mounting of G.I box in ceiling as requires with all necessary accessories including providing & fixing of 6Amps modular socket complete with modular plate and suitable size of GI box complete. -FOR VAV's.Nos.3085025,5005Wiring for 1 no. 250 V, 1 phase, 6 A (5 pin, round/flat) Raw universal switched socket outlet with 3Rx2.5 sqmm FRLS PVC insulated copper flexible sheathed cable in 2mm thick 25mm dia FRLS PVC rigid/flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of PVC flexible conduit, with all necessary accessories including providing & fixing of 6Amps modular switched socket complete with modular plate and suitable size of GI box complete.-FOR WORK STATIONS ABOVE TABLE TOPNos.Rate8506Wiring for 2 no. 250 V, 1 phase, 6 A (5 pin, round/flat) UPS universal switched socket outlet with 3Cx4.0 Upto first point & 3Cx2.5 sq.mm for looping FRLS PVC insulated sheathed copper cable along with 1.5 Sqmm FRLS PVC insulated Green copper wire for earthing in 2mm thock 25mm dia FRLS PVC rigid / PVC flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of MS flexible conduit, as requires, including providing & fixing of 2 nos. 6amps modular socket & 1 no. 16A modular switch complete with modular plate and suitable size of GI box complete. (Separate earth wire for earthing of boxes and third pin of sockets)-BREAK OUT & AHU ROOMSNos.2095019,0007Wiring for 3 no. 250 V, 1 phase, 6 A (5 pin, round/flat) UPS universal switched socket outlet with 3Rx4.0 Upto first point & 3Rx2.5 sq.mm for looping FRLS PVC insulated sheathed copper cable along with 1.5 Sqmm FRLS PVC insulated Green copper wire for earthing in 16 SWG 25mm dia MS rigid / G.I flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of MS flexible conduit, as requires, including providing & fixing of 3 nos. 6amps modular socket & 1 no. 16A modular switch complete with modular plate and suitable size of GI box complete. (Separate earth wire for earthing of boxes and third pin of sockets) FOR WORKSTATIONS BELOW TABLE TOPNos.451,15051,7508Wiring for 1 no. 250 V, 1 phase, 6 A/16 A (6pin, round/Flat) Universal type UPS switched socket outlet with 3Cx4.0 sq.mm FRLS PVC insulated sheathed copper cable & earthing of third pin & body with 2.5 sq.mm. FRLS PVC insulated Green copper wire, in 2mm thick 25mm dia FRLS PVC rigid / PVC flexible conduit, including providing & fixing of 6/16amps modular switched socket with modular plate and suitable size of GI / PVC box complete (Separate earth wire for earthing of boxes and third pin of sockets)-FOR MOT. SCREEN & OHPNos.121,15013,8009Wiring for a set of 4 no. 250 V, 1 phase, 6 A/16 A (6pin, round/Flat) UPS universal type switched socket outlet with 3C x 4 sq.mm Upto first point & 3Cx2.5 sq.mm for looping FRLS PVC insulated sheathed copper cable & earthing of third pin & body with 2.5 sq.mm. FRLS PVC insulated Green copper wire, in 2mm thick 25mm diaFRLS PVC rigid / PVC flexible conduit, including providing & fixing of 2 nos. 6/16amps modular switched socket with modular plate and suitable size of GI / PVC box complete (Separate earth wire for earthing of boxes and third pin of sockets)Nos.3501,300455,00010Wiring for 1 no. 250 V, 1 phase, 6 A/16 A (6pin, round/flat) Raw universal type switched socket outlet with 3R x 4 sq.mm FRLS PVC insulated sheathed copper cable, in 2mm thick 25mm dia FRLS PVS rigid / PVC flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of MS flexible conduit, as requires, including providing & fixing of 6/16amps modular socket along with 16A modular switch with modular plate and suitable size of GI box complete. GENERAL POWER OUTLETSNos.2095019,00011Wiring for 2 nos. 250 V, 1 phase, 6A/16 A (6pin, round/flat) Raw universal type switched socket outlets. (upto first socket outlet with 3Rx6 sq.mm & to second socket outlet with 3Rx4 sq.mm FRLS PVC insulated sheathed copper cable in 2mm thock 32 mm dia rigid / PVC flexible conduit conduit along with all fixing accerrories i.e. bend with cover, coupler, Necessary threading, T-joint & junction boxes with 16 SWG cover having a provision for fixing of MS flexible conduit, as requires, including providing & fixing of 2 nos. of 16amps modular switched socket outlets with modular plate with GI box complete. GENERAL POWER OUTLETSSets251,05026,25012Wiring for 1 no. 250 V, 1 phase, 32A moulded socket outlet with 3R x 6.0 sq.mm FRLS PVC insulated copper sheathed cable cable existing raceways / conduits, including providing & fixing of 32A moulded sockets & 32A moulded plug top & suitable size of box complete. Socket should complies IEC 320. FOR RACKS IN SERVER & LAB ROOM.Nos.1121,800201,60020PVC Trunking with junction bends, inspection joints, coupler, end covers. (MK or Equivalent make). Price should be inclusive of necessary MS painted supporved as approved.a)100x50mmRMRate90021Supply and fixing of 1 phase, modular plug and socket suitable to mount in the PVC truncking along with necessary fixing accerrories, complete in all respect.a.6/16A modular 6-Pin Round socketsNos.Rate122b.6/16A 3-Pin Round Plug TopNos.Rate6222Supply and fixing of 1 phase, moulded plug and socket along with necessary fixing accerrories, complete in all respect.a.16A moulded sockets (MDS make Cat. No. 57354 or equivalent)Nos.02440b.16A moulded straight plugs (MDS make, Cat. No. 57424 or equivalent)Nos.030223Supply, laying and connecting 1100V grade FRLS PVC insulated copper conductor 3Cx4.0 Sqmm flexible cable in 2mm thick 25mm dia FRLS PVC conduit including bends, junction boxes etc.RM50012864,00024Providing & fixing modular 400W electronic dimmers along with suitable 16G GI box & modular plate.Nos.031825Supply, installation, testing & commissioning of the False floor Power & Data outlet Boxes made up of galvanised steel, natural finish along with LID/HANDLE/FLAPS, ABS/Polycarbonate, grey color, mounting plate of 12mm thick steel, plastic coated on top, ci.Inside of the power module should have 4 nos. 5A, 5-pin round socket along with 1 nos. of 16A switch.ii2xhalf width plate each with 4x knocks-outs for RJ45 / LJ6C outlets.iii.Suitable size of knock outs on all four side of the boxes for fixing 25mm dia conduits.Nos.207,500150,000TOTAL CARRIED TO SUMMARY1,257,050BCABLES & SUB-MAINS1Supply of the following 1100V PVC sheathed and armoured XLPE insulated cables as per IS-1554 & specifications:a.3.5 core 300 sq.mm XLPE Al. Ar.RMRate1,050b.3.5 core 240 sq.mm XLPE Al. Ar.RM900925832,500c.3.5 core 185 sq.mm XLPE Al. Ar.RM3058017,400d.3.5 core 150 sq.mm XLPE Al. Ar.RM10060060,000e.3.5 core 120 sq.mm XLPE Al. Ar.RM10050050,000f.3.5 core 95 sq.mm XLPE Al. Ar.RMRate400g.3.5 core 70 sq.mm XLPE Al. Ar.RM6031018,600h.3.5 core 50 sq.mm XLPE Al. Ar.RMRate230i.3.5 core 35 sq.mm XLPE Al. Ar.RMRate175j.4 core 25 sq.mm XLPE Al. Ar.RM1800125225,000k.4 core 16 sq.mm PVC Al. Ar.RM2509423,500l.4 core 10 sq.mm PVC Al. Ar.RMRate75m.4 core 6 sq.mm PVC Al. Ar.RM2007014,000n.3 core 16 sq.mm PVC Al. Ar.RMRate80o.3 core 10 sq.mm PVC Al. Ar.RM2507117,750p.3 core 240 sq.mm XLPE Al. Ar.RMRate640q.3 core 50 sq.mm XLPE Al. Ar.RMRate1652Laying, testing & commissioning of the following sizes of cables on existing cable trays or on walls / ceiling or in existing ducts including providing & fixing saddles, clamps, nuts & bolts as required.a.3.5 core 300 sq.mm XLPE Al. Ar.RMRateb.3.5 core 240 sq.mm XLPE Al. Ar.RM9003027,000c.3.5 core 185 sq.mm XLPE Al. Ar.RM3030900d.3.5 core 150 sq.mm XLPE Al. Ar.RM100303,000e.3.5 core 120 sq.mm XLPE Al. Ar.RM100303,000f.3.5 core 95 sq.mm XLPE Al. Ar.RMRateg.3.5 core 70 sq.mm XLPE Al. Ar.RM60251,500h.3.5 core 50 sq.mm XLPE Al. Ar.RMRatei.3.5 core 35 sq.mm XLPE Al. Ar.RMRatej.4 core 25 sq.mm XLPE Al. Ar.RM18002545,000k.4 core 16 sq.mm PVC Al. Ar.RM250205,000l.4 core 10 sq.mm PVC Al. Ar.RMRatem.4 core 6 sq.mm PVC Al. Ar.RM200204,000n.3 core 16 sq.mm PVC Al. Ar.RMRateo.3 core 10 sq.mm PVC Al. Ar.RM250153,750p.3 core 240 sq.mm XLPE Al. Ar.RMRateq.3 core 50 sq.mm XLPE Al. Ar.RMRate3Supply, laying and effecting proper connection of the following 1100 volts grade PVC insulated Copper flexible conductor with non-magnetic / magnetic, armoured / unarmoured cables on existing cable trays.a.1 core 120 sq.mm Cu.unAr.RM600750450,000b.1 core 95 sq.mm Cu.unAr.RM600375225,000c.1 core 240 sq.mm Cu. Ar with non-magneticarmouringRMRate1,300d.1 core 35 sq.mm Cu. Ar., non-magnetic armouringRM10012512,500e.2 core 6 sq.mm Cu. unAr.RMRate754Supply and fixing of cable end termination of the following PVC sheathed aluminum / copper conductor armoured cables of 1100 volt grade, including cost of all crimping lugs and heavy duty compression glands, cable sockets insulation tape, sealing compouda.1 core 120 sq.mm Cu.unAr.Nos.361,00036,000b.1 core 95 sq.mm Cu.unAr.Nos.3630010,800c.1 core 240 sq.mm Cu. Ar with non-magneticarmouringNos.Rate500d.1 core 35 sq.mm Cu. Ar., non-magnetic armouringNos.101001,000e.2 core 6 sq.mm Cu. unAr.Nos.Rate2505Supply and fixing of cable end termination of the following PVC sheathed aluminum / copper conductor armoured XLPE insulated cables of 1100 volt grade, including cost of all crimping lugs and heavy duty compression glands, cable sockets insulation tape,a.3.5 core 300 sq.mm XLPE Al. Ar.Nos.Rate1,570b.3.5 core 240 sq.mm XLPE Al. Ar.Nos.181,10319,854c.3.5 core 185 sq.mm XLPE Al. Ar.Nos.28941,788d.3.5 core 150 sq.mm XLPE Al. Ar.Nos.27201,440e.3.5 core 120 sq.mm XLPE Al. Ar.Nos.26871,374f.3.5 core 95 sq.mm XLPE Al. Ar.Nos.Rate477g.3.5 core 70 sq.mm XLPE Al. Ar.Nos.44311,724h.3.5 core 50 sq.mm XLPE Al. Ar.Nos.Rate393i.3.5 core 35 sq.mm XLPE Al. Ar.Nos.Rate255j.4 core 25 sq.mm XLPE Al. Ar.Nos.322558,160k.4 core 16 sq.mm PVC Al. Ar.Nos.102392,390l.4 core 10 sq.mm PVC Al. Ar.Nos.Rate200m.4 core 6 sq.mm PVC Al. Ar.Nos.4195780n.3 core 16 sq.mm PVC Al. Ar.RMRate201o.3 core 10 sq.mm PVC Al. Ar.RM2194388p.3 core 240 sq.mm XLPE Al. Ar.Nos.Rate1,103q.3 core 50 sq.mm XLPE Al. Ar.Nos.Rate3936Supply, installation, testing & commissioning of 2.0mm thick ladder type galvanized cable tray complete with proper engineering bends, couplers, fish plates, supports & brackets etc., including the civil works requires, complete in all respects: (Note: PrCable trays in ceiling, shafts & on floori1200mm x 75mm HighRM10075075,000ii1000mm x 75mm HighRM200650130,000iii750mm x 75mm HighRM5050025,000iv600mm x 50mm flangeRM15040060,000v450mm x 50mm flangeRM25035087,500vi300mm x 50mm flangeRM10032532,500vii150mm x 50mm flangeRM5030015,0007Supply, installation, testing & commissioning of 14 SWG thick Perforated MS painted (as approved) cable tray complete with proper engineering MS bends, couplers, fish plates, supports & brackets etc., including the civil works requires, complete in all reCable trays in ceiling, shaftsi.450mm x 50mm flangeRM3070021,000ii.300mm x 50mm flangeRM5050025,000iii.150mm x 50mm flangeRM15030045,000iv.100mm x 50mm flangeRMRate2508Cable Trenches (For Earthing Cables)Excavation and Back filling of Cable trenchesDigging & Refilling : 750 mm DeepSand Cushioning : 100 mm below and above cablesProtection : Table mould bricksCftRate338Top Cover : PreCast PCC slabTOTAL CARRIED TO SUMMARY2,641,098CEARTHING1Supplying and fixing of following copper /GI tapes & Copper / AI. wires / cables along with cable end terminations & all necessary fixing accessories, and effecting connections :a.50 mm x 6 mm thick bare Cu. strip on cable tray, shaft.RM2001,100220,000b.50 mm x 6 mm thick bare GI. strip on cable tray, shaft.RM80012398,400c.25 mm x 6 mm thick bare GI strip on cable tray & shaft.RM12006274,4008 SWG bare copper copper wire. ( For DB's earthing)RM12002530,000d.6 sq.mm PVC insulated copper wire Rack Body earthing.RM5002814,000e.16 sq.mm PVC insulated copper wire in 25 mm dia 2 mm thick PVC conduit for UPS DB's earthing.RM1200125150,000f.25 sq. mm PVC insulated copper copper wires in 32 mm dia 2 mm thick PVC conduit for UPS points 3rd Pin earthing. Price should be inclusive of the end termination & requires accessores of the conduits etc, complete in all respect.RM700190133,000g.150 sq.mm PVC insulated copper ar. Cable for UPS Neutral Earthing, Price of the end termination shall not be a part of this item, same is included elsewhere in the BOQ.RM400905362,000h.End Terminations for the 150 sq.mm PVC insualted copper Ar. cable.Nos.152674,0052Supply, installation, testing and commissioning of maintenance free chemical earthing with 10 feet rod, 50mm dia, 2mm thick electrolytic grade Cu. Tube filled with chemicals and sealed at both ends and. Tube shall have leaching ports at bottom and 3 vent0The product should meet the requirements as per IS:3043 or any equivalent international specification(UL). Chemicals used shall be environmental friendly.SetsRate18,4903Providing earthing stations at locations as called for, including providing and laying 600 x 600 x 3 mm thick tinned copper electrode. 20 mm dia medium class GI pipe, CI funnel with 20 gauge GI copper wire mesh, masonry chamber with concrete base, manholeNos.129,500114,0004Providing & laying following sizes of heavy duty PVC pipe below the ground for earth strips.0a50 mm diaRM044b65 mm diaRM07405Providing & laying following sizes of B-class G.I. pipe below the ground.0a100 mm diaRM0470b65 mm diaRM02826Design, fabrication, supply, installation, testing & commissioning of the dedicated earthing box made up of 16 SWG Powder coated sheet of approved shade with door lock arrangement. Dedicated earthing bar should of eannealed copper bar of 25x6mm mounted on SMS insulators.lenght of the bars & box should suitable for connecting of 20nos of 1c*6 sqmm copper cables.price shuld includes all the accessories for fixing hardware of box in basement etcSet44,00016,000Note:Earthing quantities may vary as per site conditions as exact layout / location of earth pits is not yet finalized.TOTAL CARRIED TO SUMMARY1,215,805DSUPPLY OF LIGHTING FIXTURES1Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Phillips TCH 114/2005/865 HF or equivalent.)Nos.4095038,0002Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Philips TCH 128/2005/865 HF).Nos.501,05052,5003Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Wipro WRF 25136 or equivalent.)Nos.2065013,0004Decorative Halogen spot light with 50W / 12 V lamp recessed fixture including electronic transformer & complete in all respects. (ceiling recessed) Cat. No. Wipro Compact WCQ 21150 or as approved / equivalent.Nos.3065019,5005Wipro or equivalent make- Direct / Indirect suspended type light fixture with horizontal support for strenghtening of suspension arrangement partly perforated luminare suitable for 2x28W T-5 FTL lamp & electronic ballast (Cat. No. Keslec 214-SS254 or as aNos.3505,2001,820,0006Recessed type light fixture with suitable for gyp. ceiling with 2x36 Watt FTL & electronic ballast complete in all respects (Cat. No. Keslec New Lux WW 1x36 H.F or equivelant).Nos.222,70059,4007KAVA recessed wall luminare suitable for 1x18 Watt CFL lamp completely wired with electronics ballast & lamps (Cat. No. Zumtobel Staff Keselec KAVA 118-HF).Nos.04,7258Pendent mounted type 4'x1' Light fixture with mirror optic reflector suitable for 2x36Watts FTL lamp. Price should be inclusive of the vertical suspension rods & fixing arrangement, complete in all respect. (Cat No. Keslec KMOC 2x36W H.F. or equivalent)Nos.Rate2,1389Circular recessed down lighter aluminised polycarbonate optics with highly transparent, scratch resistant coating with metal housing suitable for 2x18Watt CFL lamp completely wired with electronics ballast & lamp (Cat No. Keselec Nova 2x18 H.F or as appriNos.1502,800420,00010Same as item No. 9 but suitable for 1x18 Watt CFL with lamp.Nos.03,60011Square Grid Direct/Indirect light fixture with 2 nos. 36Watt CFL lamp & necessary electronic ballast along with necessary suspension accessories complete in all respect.Nos.502,400120,00012Decorative type Pendent light fixture houseed in color glass housing with 4x42Watt CFL lamp complete with SS suspension along with accessories with 4x42Watt CFL lamp. (Cat. No. Artlite ESSEDRA)Nos.Rate38,70013Recessed type Square type Light fixture with 2x18Watt CFL lamp completer with electronic ballast & 2x18Watt lamp. (Cat. No. FIAM-ART No. 6504 or GCP - 15218 Wipro make or equivalent)Nos.201,60032,00014Recessed type LED light fixture complete with chock & necessary SS finished ring on top flushed with finsh floor level. (Cat No LF01/008W/B015/WWA or equivalent complete with power supply units as requires))Nos.Rate16,48215Bulk head light fixture housed in Aluminum extruded housing with transperant glass on Top, housing should complies IP-56 protection. Light fixture should be complete with 1x18Watt CFL lamp & electronic ballast.Nos.Rate5,625164.5 Mtrs. High 50mm Dia 2.63mm thick MS painted pole with 1 nos. 150Watt MH light fixture suitable for external applications complete with gear box, control panel & 150Watt MH lamp, price should be inclusive of all fixing accessories.Nos.Rate2,025Notes:aAll fixtures shall be complete with lamps and control gear.bAll fluorescent tube light fixtures shall be complete with control gear & power factor improvement capacitor.cNecessary down rods, hanging chains etc shall be part of the fixtures.dSamples of all the fixtures shall be submitted to the architect before supply & approval is taken.ePlease check the quantity from drawings / architect / consultant before ordering.TOTAL CARRIED TO SUMMARY2,574,400EFIXING OF LIGHTING FIXTURES1Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Phillips TCH 114/2005/865 HF or equivalent.)Nos.40753,0002Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Philips TCH 128/2005/865 HF).Nos.50753,7503Fluorescent Light Fixture surface type with TRUELITE tube complete in all respects and with electronic ballast etc. as required (Cat. No. Wipro WRF 25136 or equivalent.)Nos.20751,5004Decorative Halogen spot light with 50W / 12 V lamp recessed fixture including electronic transformer & complete in all respects. (ceiling recessed) Cat. No. Wipro Compact WCQ 21150 or as approved / equivalent.Nos.30752,2505Wipro or equivalent make- Direct / Indirect suspended type light fixture with horizontal support for strenghtening of suspension arrangement partly perforated luminare suitable for 2x28W T-5 FTL lamp & electronic ballast (Cat. No. Keslec 214-SS254 or as aNos.35010035,0006Recessed type wall washer light fixture with suitable for gyp. ceiling with 1x36 Watt FTL & electronic ballast complete in all respects (Cat. No. Keslec NewLux WW 1x36 H.F or equivelant).Nos.221002,2007KAVA recessed wall luminare suitable for 1x18 Watt CFL lamp completely wired with electronics ballast & lamps (Cat. No. Zumtobel Staff Keselec KAVA 118-HF).Nos.01008Pendent mounted type 4'x1' Light fixture with mirror optic reflector suitable for 2x36Watts FTL lamp. Price should be inclusive of the vertical suspension rods & fixing arrangement, complete in all respect. (Cat No. Keslec KMOC 2x36W H.F. or equivalent)Nos.Rate1009Circular recessed down lighter aluminised polycarbonate optics with highly transparent, scratch resistant coating with metal housing suitable for 2x18Watt CFL lamp completely wired with electronics ballast & lamp (Cat No. Keselec Nova 2x18 H.F or as appriNos.15010015,00010Same as item No. 8 but suitable for 1x18 Watt CFL with lamp.Nos.010011Square Grid Direct/Indirect light fixture with 2 nos. 36Watt CFL lamp & necessary electronic ballast along with necessary suspension accessories complete in all respect.Nos.501005,00012Decorative type Pendent light fixture houseed in color glass housing with 1x18Watt CFL lamp complete with SS suspension along with accessories with 1x18Watt CFL lamp. (Cat. No. Artlite ESSEDRA)Nos.Rate10013Recessed type Square type Light fixture with 2x26Watt CFL lamp completer with electronic ballast & 2x26Watt lamp. (Cat. No. FIAM-ART No. 6504)Nos.201002,00014Recessed type LED light fixture complete with chock & necessary SS finished ring on top flushed with finsh floor level. (Cat No LF01/008W/B015/WWA or equivalent complete with power supply units as requires))Nos.Rate10015Bulk head light fixture housed in Aluminum extruded housing with transperant glass on Top, housing should complies IP-56 protection. Light fixture should be complete with 1x18Watt CFL lamp & electronic ballast.Nos.Rate100164.5 Mtrs. High 50mm Dia 2.63mm thick MS painted pole with 1 nos. 150Watt MH light fixture suitable for external applications complete with gear box, control panel & 150Watt MH lamp, price should be inclusive of all fixing accessories.Nos.Rate100Notes:aAll fixtures shall be complete with lamps and control gear.bAll fluorescent tube light fixtures shall be complete with control gear & power factor improvement capacitor.cNecessary dow