1

2.

3.

4.

5.

6.

7.

1.

2.

3.

4.a) The Tenderer shall furnish copies of :

i) IT Registration Certificate with No.

ii) Sales Tax Registration Certificate with No.

iii) Service Tax Registration Certificate with No.

iv) Electrical Contractor's License with No.

v) Electrical Supervisor’s License with No.

5.

a)

b)

c)

d)

e)

1.

2.

Part 'B' of the tenders will be opened for those only who fulfils the qualifying criteria given in the tender document.

The unopened part 'B' along with Earnest Money deposit for those not fulfilling qualifying criteria will be

returned.Alternation/change in tender documents is to be authenticated.

Clarifications, if any, required on drawings, schedules, specifications, etc. can be obtained from our Consultant

M/s.Alinda 33,Santoshpur Main Road,Kolkata 700 075 Phone No -033-2425 0569,94337 98849

The Tenderer should also submit the following documents along with the Tender.

List of technical persons available on hand, years of their association with the firm & proposed to be engaged for the

subject work, if selected (marked Annexure-IX) ;

The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders

without assgming any reason whatsoever.

marked Annexure - VI

marked Annexure - VII

marked Annexure - VIII

List of works in hand indicating description of work, contract value, approximate value of balance work yet to be

done and date of award (marked Annexure-XII)

Contractors will be required to arrange for their own storing. Dismantled materials are to be carted away from site at

their own cost and disposed of in conformity with Municipal regulations.

Tenderer who will quote the rate must have a local office at Kolkata. This is absolutely essential for day to day

supervision & coordination of the work at site.

All informations are to be fully authenticated & documented failing which the documents submitted will not be accepted.

GENERAL TERMS & CONDITIONS

The tenderer are to visit the site and acquaint themselves with site conditions before quoting rates.

Bank of Baroda

Bank of Baroda, West Bengal, Sikkim & A & N Island invites sealed tenders in two bid system for the proposed

Civil,interior & electrical work of Jalpaiguri, Kadamtala Main Road,1st Floor,Ukilpara Jalpaiguri Dt Jalpaiguri Pin-

735101 The work is to be completed within 21 days.

List of important plant & machinery available on hand (own) and proposed to be inducted (own & hired to be given

separately) for carpentry & electrical work (marked Annexure-X)

List of works completed in the last (three) financial years under Bank / Govt., Semi - Govt,Govt. undertaking /

Corporate Sectors giving description of work, organisation for whom executed, approximate value of contract at the

time of award, date of award and date of scheduled completion of work, date of actual completion and final value

of contract should also be given (marked Annexure-XI)

marked Annexure - V

(Government of India Undertaking)

NOTICE INVITING TENDER

Interested agencies having experience in work of similar nature & magnitude and fulfilling the eligibility criteria given

below may download detailed tender document from Bank's Website http:bankofbaroda.com/tenders.asp

marked Annexure - IV

The tenderer should have completed in last three Financial years (i.e. current year & two previous financial year) in

Bank, Govt. or Govt. undertaking and Financial Institutions, Corporate Sectors, etc. minimum 3 (three) similar

composite work (Interior Furnishing & Electrical) costing not less than Rs. 15.00 lacs in single contract. (Work order &

completion Report in support must be submitted & marked as Annexure-I)

The total contract amount received by the Tenderer during the last 3 financial years should be minimum as 40.00 lacs

per year in contract work. In support of this the Tenderer should submit audited sheet duly Certified by the Chartered

Accountant & marked Annexure-II.

The Tenderer should produce Solvency Certificate from any Nationalised / Scheduled Bank for an amount of 200% of

the advertised Tender value marked Annexure-III.

Part 'A' envelope (Technical Bid) shall contain : Earnest Money, the documents for satisfying eligibility criteria & the

technical & financial stipulation, if any, of the tenderer & Part 'B' shall contain : financial bid along with a copy of the

tender document, duly signed in all pages both shall be separately sealed & submitted in another sealed envelope

to the Deputy General Manager, Bank of Baroda, West Bengal, Sikkim & A & N Island, BARODA TOWER, Plot No. 38/2,

Block GN, Sector-V, Salt Lake City, Kolkata : 700 091, before 2.30 P.M. on 06.02.2012 along with Earnest money

amounting to Rs. 10,000/- by Bank Draft / Pay order in favour of Bank of Baroda shall be submitted in Part 'A'.

MINIMUM ELIGIBILITY CRITERIA (Shall be submitted with Part A of the Offer)

Part 'A' will be opened at 3.30 p.m. on 06.02.2012.

1

3.

4.

5.

6.

7

8.

9.

10.

11.

The quoted rates, are to include cost of all materials, labour and or any other material, all statutory taxes, transport,

handling delivery at site and installation, complete in all respect, as per drawing, directions or instructions of

Employer/Consultant. The quoted rates are also to include dismantling of partitions, counters, old electrical wirings

etc. and stacking serviceable materials and disposal of debris, etc.

Prior approval of the Employer/ Consultant shall be obtained for colour and thickness of laminates to be used in the

work.

The arrangement for “ Wire Management " is to have prior approval of the Client.

The quoted rates shall remain firm during the entire currency of contract. No price variation for any causes

whatsoever, shall be entertained.

The time of completion shall be 21 days from the date of placement of order.

The offer shall remain valid for acceptance for a period of 30 days from the date of submission of offer.

The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders

without assgming any reason whatsoever.

Payments will be made once on completion by the Employer within 15 days after certification of bill by the

Consultant 10% of the total payable amount is to be retained as retention money and will become due for release

after expiry of six months from the date of completion of the installation & subject to satisfactory maintenance of the

executed work.

Tenders addressed to Deputy General Manager, Bank of Baroda, West Bengal & Sikkim Region and submitted at his

office at BARODA TOWER, Plot No. 38/2, Block GN, Sector-V, Salt lake City, Kolkata : 700 091, before 2.30 P.M. on

06.02.2012, accompanied by Earnest Money amounting to Rs.10,000/- by Bank draft payable to Bank of Baroda and

other documents as mentioned in NIT. Part 'A' of the tenders will be opened at 3.30 P.M. on the same date.Part 'B' will

be opened immediately after opening of Part 'A'.

2

SPECIFICATION OF MATERIALS FOR INTERIOR WORK

Sl.No. Description

1. Laminate

2. Ply & Block Board

3. Glass

4. False Ceiling & Accessories

5. Veneer

6.Textured Wall Paint

7. Glue

8. Locks

9. Aluminium Hardware Fittings

10. Brass Hardware

11.

Floor Spring

12. Screws

13. Casters

14. Sliding Drawers / Channels

15. Furnishing Fabric

16. Leather Foam

17. PVC Flooring

18. Carpet

Earl Behari / Efficient Gadjets

Make (s)

Metako / Allen / Crown with ISI Mark

India Gypsum Ltd.

Marino / Greenlam / Century / Archid

Green / Century / Archid / Austin

Modi / Indo Ashahi / Float Glass India Ltd.

Glamour or Favourite (Balla Industries)

Woven type "Harmony" range from "Vimal"

or equivalent

Bhor Industries or equivalent

Armstrong / Krishna / Premier

Durian / Century / Archid

ICI, Jenson & Nicholson / Asian paint /

Berger

Efficient Gadjets

Evrite Agencies Pvt. Ltd. / Nita Floor Spring

Nettle Fold

ICI, Spectrum, Heritage

Godrej / Secur / Yale

Brass Arts / Vijoy

3

SPECIFICATIONS OF MATERIALS FOR ELECTRICAL WORK

Sl.No. Description

1. Switch fuse / fuse switch units (HRC) (32A TPN & above)

2. Timer (TSQ 100)

3. Voltmeter & Ammeter

4. Voltmeter & Ammeter selector switches

5. Phase indicating lamp

6.

7. Capacitor

8. HRC fuses

9. Power Cable : XLPE

10.

11. HRC fuse base & carriers.

12. PVC terminals

13. 1.1 KV grade PVC insulated armoured aluminium cable (ISI marked)

14. 1.1KV 660V grade PVC insulated & sheathed / insulated copper wire &

flexible cords (ISI marked).

15. Moulded case circuit breaker

16. RCCB / ELCB

17. Switch fuse with rewirable fuses. (6A & 32A TPN)

18. Isolator

19. Changeover switch (on load type)

20. MCB distribution board

21. Distribution fuse board with rewireable fuses

22. Miniature circuit breaker / MCB type isolator

23. Contractors

24. Auxiliary contractor

25. 1/16 Amp Piano key type switch / flushed type plug socket

26. 6/16 Amp modular switch / socket, module plate & mounting M.S. /

PVC box.

27. 300W, 2 module electronic regulator

Make (s)

HAVELL’S / STANDARD

Vaishno / SIEMENS / ROSS controls

L & T

GE power / SIEMENS / L&T / Schneider

A. E. / IMP

ELMEX / ESSEN

SIEMENS / L & T/BCH

SIEMENS / L & T

KAYCEE / L & T

UNIVERSAL / GLOSTER / NATIONAL / NICCO

/

L & T / SCHNEIDER/LEGRAND

CPL (Genius) / ANCHOR (Roma) / CRABTREE

/

MK

ANCHOR (Roma) / CRABTREE / MK

ANCHOR / PRECISION / SSK & RIDER

HAVELL’S / STANDARD

NATIONAL/FINOLEX/ HAVELLS

LEGRAND / SIEMENS

HAVELL’S / BPC / BOSMA

KENBAR / HAVELLL’S / ELCON / HPL /

CONTROL & SWITCHGEAR.

LEGRAND/ SIEMENS

A E / KAPPA SEGC & CONTROLS / CONTROL

CROMPTON/SIEMENS

TATA LEVERT/NEUMERIC/ KIRLOSKAR

GLOSTER/INCAB/POLYCAB/CINOLEX

GE power / SIEMENS / L & T / SCHNEIDER

SWITCHGEAR

GE Power/SIEMENS/L&T/SCHNEIDEV

LEGRAND/ SIEMENS / L&T

4

Sl.No. Description

28. Ceiling rose

29. Holder

31. Luminous indicating type buzzer with cancellation push.

32. Alarm bell.

33. G.I. pipe

34. Steel conduits (conforming to IS in all respects)

35. Black enamelled

36. Galvanised

37. Non-metallic PVC conduit pipe

38. Compression type brass gland

39. Cable termination socket

40. Light fitting & lamps

41. Decorative/Ornamental /Chandelier / Light Fittings

42. Ceiling Fan

43. Exhaust fan

44. Industrial type socket & top

45. Telephone wire

46. Telephone Socket

47. Network Cable

48. Contractors

49. STARTERS

Make (s)

KAY / EPP / ANCHOR / JJ

Good local make with minimum wall

thickness of 3 mm. for 19 / 20 mm. and 25mm

sizes & 2.5 mm. for 12mm. sizes

BEC / SUPREME / AKG

BEC / SUPREME / AKG

BST / BANSAL

KHERAJ / GETCO

KAY / EPP / ANCHOR / JJ

NATIONAL / HOMA / EQUIVALENT

DOWELL'S

WIPRO or equivalent

DOWELLS / JOHNSON / COMET

PLAZA / KALINGA/ PRECISION/AKG or

equivalent

FINOLEX or equivalent

L & T / SIEMENS

CROMPTON / POLAR / KHAITAN

NORTH WEST / CABTREE

CROMPTON / POLAR / KHAITAN

HAVELL’S / CROMPTON / LEGRAND

FINOLEX / RRK/NATIONAL

CRABTREE/MK

CROMPTON / POLAR / KHAITAN / EPC

5

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

1.00 Supplying and laying true to line and level vitrified tiles of approved brand

size not less than 600mm x 600mm x 10mm thick in floor , skirting etc.

using polymerised adhesive (as per manual of the applicator ) over

existing floor finish , after preparing the same by means of cleaning ,

scrapping as necessary for existing floor, joints grouted with admixture of

white cement and colouring pigment to match with colour of tiles

complete finishing in all respect as per instruction sqm. 40

2.00 Striping of worn out plaster, renewing with new plaster work (1:6)

of sand cement morter of 15mm/20mm ( making level as per site condition)

mixing with water proofing agent ( Sika Latex or similar make) mixing

as per applicator's manual matching with old plastered surface and

complete in all respect sqm. 40

4.00 Removal of rubbish, earth etc. from the working site

and disposal of the same, beyond the compound, in

conformity with the Municipal/Corporation Rules for

such disposal, loading into truck and cleaning the site

in all respect as per direction of Engineer-In-Charge Cum. 10

5.00 Removing old tiles and fitting and fixing 1st quality ceramic tiles of

approved size, shade and brand in wall and floor including borders

to match with existing work where applicable, set in sand cement

mortar (4:1) including backing concrete(1:2:4)and 4nos.

key stone (10mm) fixed with areldite at the back

of each tile and finishing the joints with white cement

mix with colouring oxide (if requested) to match the

colour of tile

i) FLOOR sqm. 45

ii) DADO (TOILET) sqm. 20

ii) DADO (KITCHEN) sqm. 6

6.00 BLACK STONE PANTRY COUNTER (2'-0" WIDE)

Providing and laying platform of 3/4" thk. & 2' width (clear) and at

2'-8" height (top) above fl. of approved Kota stone with champhered and

machine polished edge. It shall be supported on wall on 11/2" thk

horizontal kota stone. Rate shall include the profile cutting and

fixing of below counter wash basin/kitchen sink & polishing the

exposed edges. A 2" kota stone shall be provided

below the champhered edge. sqm. 7.6

7.00 Stainless steel sink

P/F/F Stainles Steel sink with single bowl of Nirali make, integrated

waste size-over all 600 x 450 mm. with a pair of C.I. bracket, fitted with

15mm dia. Brass C.P. Pillar tap & 32 mm. dia white pvc waste pipe No. 1

with brass coupling etc. complete.

9.00 Spot application for insecticides using aqua base sprey for pest ( for

bugs, cockroaches, silverfish, termites etc ) to walls and ceiling etc.

INTERIOR WORKS OF OF BANK OF BARODA

JALPAIGURI BRANCH

PRICED BILL OF QUANTITIES FOR CIVIL WORKS

DESCRIPTION OF ITEMS

Civil works of Jalpaiguri Branch, BOB. Consultant : ALINDA

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

DESCRIPTION OF ITEMS

with chemical emulsion by admixing chloropyrofos emulsifiable

concentrates (1% concentration ) with water by weight including

spraying the emulsified chemical @0.5 ltr. Per sqm. on wall surfaces ,

ceiling , electrical lines including drilling holes in places where source of

termite is detected squirting chemical solution into the holes and sealing

with cement grout , finish in all respect. sqm. 650

11.00 Rendaring the surface of walls and ceiling with plaster of paris

( thickness not less than 1.5 mm) matching with old pop surface. sqm. 45

12.00 Painting of doors and windows with synthetic enamel paint(02 coats) of

approved make and shade after applying 02 coats of oil bound primer

of approved make including smoothening of surfaces with putty as

necessary , complete in all respect. sqm. 190

13.00 Applying two or more coats of Acrylic Emulsion paint of

approved shade and brand, over a coat of primer to give

a even shade on wall / ceiling surface including preparation

of surface complete with labour and material. sqm. 425

14.00 Supplying fitting and fixing of 2100 high PVC door

of approved make and thickness along with PVC

door frame , clamp, hinges, bolts and

all other necessary fittings complete in all respect set 2

SANITARY & PLUMBING FITTINGS AND FIXTURES

Supplying fittings and fixing of following s&p fittings

and fixtures of Jaquar /Cera or similar make where

applicable as per approval of the authority

15.00 Swan-neck piller cock for sink no. 1

16.00 EPWC with cistern & fittings copmlete of approved make no. 2

17.00 350x550 wash basin with fittings copmlete of approved make no. 2

18.00 Chromium plated pillar cock of approved make no. 2

19.00 Chromium plated bib cock of approved make no. 2

20.00 Chromium plated Towel ring 150 dia no. 2

21.00 Chromium plated soap tray no. 2

22.00 Comprehensive sanitary and plumbing works for 02 nos. toilets

& 1 no. pantry along with supplying , fitting and fixing of

necessary waste pipes and plumbing pipe , loft tanks

lines of required dia , stop cocks of approved make,

complete as per direction of engineer in charge. L.S.

0.00

NOTE All debries are to be removed from site in conformity with local regulations. Rates to include this.

TOTAL COST FOR CIVIL AND SANITARY & PLUMBING WORKS

Civil works of Jalpaiguri Branch, BOB. Consultant : ALINDA

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

1.00 FALSE CEILING

Providing and fixing in position dropped ceilling in two levels

including vertical surfaces in between two level of ceiling surface

with 12.5mm thick tapered edge gypsum board conforming to

IS 2095 including providing and fixing of framework made of

special sections power pressed from MS Sheet and galvanised

in accordance with Zinc coating 600 as per IS 277 and costing

of angle cleats of size 25mm wide x 16mm thick with flanges

of 22 mm and 37 mm at 1200mm center to center one flange

fixed to the ceiling with dash fastner 12.5mm dia x 40mm long

6mm dia bolts to the angle hangers of 25x25x5 mm of required

length and other end of angle hanger being fixed with nut and

bolts to g.I Channels 45mm x 15 mm x 0.9 mm running at the

rate of 12 mm centre to centre to which the ceiling section

0.5mm thick botton wedge of 08mm with tapered flanges of

26mm each having clips of 10.5mm at 450mm center to centre

shall be fixed in a direction perpendicular to G.I. Channel with

connecting clips made out of 2.64 mm dia x 230mm long G.I.

Wire at every junction including fixing the gypsum board with

ceiling section and perimeter channel.

The perimeter of ceiling fixed to wall/partition with the help of

rawl plugs at 450mm center with 25mm long drive all screws

@ 230mm interval including jointing and fixing to a flush finish of

tapered and square edges of the gypsum board with

recommended filter, paper tapes, finisher and two coats of

primer suitable for gypsum board as per manufactures

specification and also include the cost of making openings for

light fittings grills, diffusers, cutouts made with frame of

perimeter channels of the Engineer-in-Charge but excluding the.

cost of painting.

Rates to include cost of making openings for ceiling mounted

electrical/air-conditioning accessories as per instructions.

(The work to be carried out through authorized applications of

M/s. India Gypsum Ltd.) sqm. 110

2.00 DOUBLE SKIN PARTLY GLAZED FULL HEIGHT PARTITION

Supplying and erecting Full Height Partly Glazed partitions

up to 8' 6" high) as per drawing and conforming to the

following specifications :

Basic Framework : Well seasoned Malayasian sal wood

sections, treated with two coats of wood preservations, 50mm

x 50 mm (minimum) at maximum 600 mm horizontal or

vertical spacing as per site conditions. Vertical Members shall

be suitably anchored and at ceiling level to ensure rigidly.

Exposed frame members in the glazed portions shall have

wider spacing (approx. 1800 mm clear) as per instructions.

Exposed members shall be finished with 1.0mm thick laminate

sheet of same or combination shades, 2 x 6 mm BWR

grade plywood facing including 4x4 mm grooves at locations

as per instruction.

Skin Membrane : (Opaque portion upto 900 mm from floor

level with 2 x 6 mm thick BWR grade plywood on each face

with 4x4mm grooves formed at the top layer as per drawings /

instructions.

Finishing : 1.0mm thick laminate sheet of same or

combination shades as per instructions.

Skirting : 100mm high x 12mm thick polished white or steam

beech wood skirting on both faces with NC lacquer in Matt finish.

Glazing : 6mm thick clear float glass fixed with continuous

White or Steam Beech wood glazing beads of approved shape

(finished 35x25mm) all around, polished & coated with NC

lacquer finish. The rate should also include cost of decorative

etching on one side of the glass.

Quoted rates shall include all necessary materials, accessories

and also allow provisions for electrical/telephone/computer

wiring conduits and switch boxes, etc (Materials of wiring sqm. 35

INTERIOR WORKS OF BANK OF BARODA

JALPAIGURI BRANCH

PRICED BILL OF QUANTITIES FOR INTERIOR & FURNISHING WORKS

DESCRIPTION OF ITEMS

Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

DESCRIPTION OF ITEMS

3.00 FULL HEIGHT SOLID PARTITION

Supplying and erecting full height opaque partitions (from 8'6"

10ft. High) as per drawing and conforming to the following

specifications:

Basic Framework : Well seasoned Malayasian sal wood

sections, treated with two coats of wood preservatives, 50mm

x 50mm (minimum) at maximum 600 mm horizontal or

vertical spacing as per site conditions. Vertical Members shall

be suitably anchored and at ceiling level to ensure rigidity.

Skin Membrane : 2x6 mm thick BWR grade plywood as per

drawings/instructions.

Finishing : 1.0mm thick laminate sheet of same or

combinations shades as per instructions.

Skirting : 100mm high x 12 mm thick polished white or steam

beech wood skirting on both faces with NC lacquer in Matt finish.

Other specs same as item no.2

Skirting : 100mm high x 12 mm thick polished white or steam

beech wood skirting on both faces with NC lacquer in Matt finish.

Other specs same as item no.2 sqm. 25

4.00 MAIN ENTRANCE DOOR

Providing & fixing in position Twin stile door made of 40 mm

thk well seasoned teak wood of top & bottom stiles, fixed

portion with 8 mm thk. Clear float glass & openable portion

with double shutter made of 12 mm thk clear float glass with

necessary hardware fixtures of approved make & design,

viz. double action ISI marked floor springs, on which the

shutters are pivoted at the top & bottom, brass flushbolt,

satin finish stainless steel decorative tubular handles on

both the faces, (Dorset or equivalent approx. 300 mm long)

complete as per direction. Rate should include etching of the

Bank's logo & emblem on the Glass in the size & design as

approved by the architect. Wooden surface should be

polished in approved shade N.C. Lacquer in matt satin finish.

a) Openable Shutter sqm. 2.5

5.00 SOLID FLUSH DOOR

Supplying and fixing in position overall 37mm thick solid core

hot pressed phenol formaldehyde bonded approved flush door

shutter finished with 1.0mm thick laminate sheet of approved

shade and quality on both sides of the door shutter including cost

of hardware fittings e.g. mortic locks, brass hinges, door handles

etc. of approved make

a) Average size of shutter (D2) : 0.75m x 2.1m nos. 4

b) Average size of shutter (D1) : 0.90m x 2.1m nos. 1

6.00 PARTLY GLAZED DOOR SHUTTER

, Providing, fixing & fitting in position Door shutters made of

specification similar to that of item (5) hinged on 3 nos.

brass hinges as required with the exception that the wooden

frame is of section 2" x 1.5". The cost of all fittings: handle

locks, aldrop handles door closer, night latch all of approved

make to be included. The glazed portion will be between

3'-0" to 6'-8" of 5mm thk. Glasspanes of approved quality.

Average size of shutter (D3) : 0.9m x 2.1m nos. 2

Average size of shutter (D4) : 0.75m x 2.1m nos. 2

7.00 WOODEN PANELLING ON WALL AND PILLARS

Wall Panelling / column encasing (upto 2700 mm high) works

as per drawing and conforming to the following specifications :

Basic frame work

Well seasoned Malayasian Sal Wood sections, treated with two

coats of wood preservatives, minimum 50x25mm, at suitable

horizontal / vertical spacing not exceeding 600 mm c/c.

Skin Membrane

2x4 mm thick BWR grade plywood with 4x4mm grooves formed

at top layer as per drawing/instructions.

Finishing

1mm thick laminate sheet of same or combination shades as per

instructions.

Skirting

100mm high x 12mm thick polished white or steam beech wood

skirting with NC lacquer finish.

Quoted rates shall include all necessary materials, accessories

and labour and also allow provisions for electrical/telephone/

computer wiring conduits and switch boxes etc. complete with

necessary jacking/thickening of panels to accommodate

Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

DESCRIPTION OF ITEMS

conduits/switch boxes. (Materials for wiring conduits and switch

boxes shall be separately paid for). sqm. 35

Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA

SL. UNIT QNTY. RATE AMOUNT

NO. Rs. P. Rs. P.

DESCRIPTION OF ITEMS

8.00 Writing Ledge

P/F/Fcheque writing tables made of 1 no. 19mm plywood shelf 3' (w) x

1' (d) x 3'(h) which is finished with 1mm thick Laminate on all exposed

surface. The shelf is fixed with two intermediate 8mm thk glass

partition fixed with D brackets for keeping withdrawal/deposit forms.

The table top shall be of 12mm thick plain glass fixed with SS studs

on the shelf.

Item is to be completed in all respects as per direction of Architect no. 1

9.00 PLASTER OF PARIS CORNICE

Providing and fixing Plaster of Paris Conice (out of 65x65mm sections)

at junctions of false ceiling, walls and at other locations. RMT. 85

10.00 FULL HEIGHT FILING CABINET/ALMIRAHS

Full height Filing cabinet/Almirahs 1'-4" deep & upto false ceiling height

of 8'-6" made of 18mm BWP blockboard with intermediate shelves. The

back of the cabinet to be made of 6mm thk. BWP ply with a ply skirt-

ing/base of 100mm high. There will be three sets of shutters above 3'-6"

height below 3'-6" height & above 7ft. Height. There will be vertical divi-

ders of same block board at approx. 3ft. Apart on which the shutters are

hinged. All exposed surfaces are finished with 1.5mm thk. Decorative

laminet of approved make & shade. All exposed edges of the commercial

ply & the block board are to be finished with 1/4" thk. Rubber wood

lipping which are to be melamine polished as directed. Cost of all fitting

like brass hinges, Godrej locks, magnetic catches, powder coated "D"

type steel matt finish metal handles shall be inclusive. sqm. 18

11.00 Low height Filling cabinet 1'4" deep & upto height of 2'-8"

made of 18mm BWP blockboard with intermediate shelves

The back of the cabinet to be made of 6mm thk. BWP ply with a

BWP ply with a ply skirting /base of 100mm high.

There will be one horizontal division and vertical dividers of

same block board at approx. 3ft apart with sliding shutters.

All exposed surfaces & the shutters are finished with

1.0 mm thk decorative laminate of approved make & shade

Cost of all fittings like brass hinges, godrej locks, magnetic

hinges, godrej locks, magnetic catches, steel matt finish "D"

type handles shall be inclusive.

Skirting

100mm high x 12mm thick polished white or steam beech wood

skirting with NC lacquer finish. sqm. 5.5

12.00 WINDOW SCREEN

Providing, fitting in position 100mm vertical blinds made of

best quality PVC coated polyester fabric of approved make

& shade & to be tailored to the size of the window. sqm. 20

13.00 Display Panels

Providing & fixing in position frameless double acrlyic trans-

parent sheet 2600X1200 (w) mounted with mirror screws

/nuts on the wall along with all accessories complete for

display of bank's schemes/posters/notices inserted on it. nos. 1

14.00 PIN-UP NOTICE BOARD

Providing, fitting in position pin-up board made of soft

cork board finished with the fabric as approved, matching

with the colour scheme of the banking hall with a R.W.

moulding all around the edges.(1200x750) sqm. 1

NOTE All debries are to be removed from site in conformity with local regulations. Rates to include this.

TOTAL OF INTERIOR AND FURNISHING WORKS

Interior works of Jalpaiguri Branch,BOB Consultant : ALINDA

ELECTRICAL WORKS OF BOB , JALPAIGURI BRANCH

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

A. CONCEALED WIRING (Supply and Installation)

(Including supply of materials, groove cutting in wall

and makig good damage to original finish)

A1) Point wiring for Light/Fan/Exhust through concealed

conduit. These include:

a) 2 nos. 1.5 Sq.mm PVC insulated (FRLS) stranded

copper wire 1100V grade. (Make- Polycab, Finolex

& Mescab)

b) 1 no. 1.5 Sq.mm PVC insulated (FRLS)stranded

copper wire 1100V grade for earthing.

c) 16 SWG G.I. Junction Box (100x100x62 mm) with 5

mm thick acrylic cover and fixing accessories.

d) 1.6mm(16 SWG) thick painted MS switch box

e) 6A, 240V Moduler switch to be mounted on

switchboard .(Make- MK,& ABB)

f) Required module number of mounting frame with

sheet cover

g) A two/three way circular box to be provided for each

light point in brick wall.

i) - Length upto 6 metre Nos. 90

Note :

i) Min 2 nos. PVC conduit of 20mm dia to be laid

between switchboard and junction box which is

vertically in the same line with the switch board, if

required.

ii) All junction boxes shall be mounted in the same

level in their respective room.

iii) Vertical position of junction box shall be fixed in the

same line with the switchboard.

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

A2) 6A receptacle (RA Type) wiring from nearest

JB/Switch Board to independent 6A, 5 pin, 240V

receptacle by supplying & laying of 1100V grade 2-

1/Cx1.5 Sq.mm + 1-1/Cx1.5 Sq.mm for earthing

PVC insulated (FRLS) copper wire through PVC

concealed conduit in wall/floor with groove cutting

and making good damage to original finish including

supply of necessary sheet metal pull box/ circular

box with 5mm thick acrylic sheet cover(Make-

Polycab,Finolex, & Mescab)

Meter 190

A3) 16/6A (RB Type) receptacle wiring from Distribution

Board/nearest JB to independent 16/6A, 6 pin, 240V

receptacle by supplying & laying of 1100V grade 2-

1/Cx2.5 Sq.mm + 1-1/Cx1.5 Sq.mm for earthing

PVC insulated copper wire through PVC concealed

conduit in wall with groove cutting and making good

damage to original finish including supply of

necessary sheet metal pull box/ circular box with

5mm thick acrylic sheet cover (Make-

Polycab,Finolex, & Mescab)

Metre 90

A4) Circuit wiring from Distribution Board/nearest JB to

Switch Board/Work stations by supplying & laying of

1100V grade 2-1/Cx4 Sq.mm + 1-1/Cx2.5 Sq.mm

for earthing PVC insulated (FRLS) copper wire

through PVC concealed conduit in RCC slab/wall

with groove cutting and making good damage to

original finish including supply of necessary sheet

metal pull box/ circular box with 5mm thick acrylic

sheet cover (Make- Polycab,Finolex, & Mescab)

Metre 50

A5) Power unit for A.C wiring by supplying & laying of

1100V grade 2-1/Cx6 Sq.mm + 1-1/Cx2.5Sq.mm for

earthing PVC insulated (FRLS) copper wire through

prelaid PVC concealed conduit in wall with groove

cutting and making good damage to original finish

including supply of necessary sheet metal pull box/

circular box with 5mm thick acrylic sheet cover

(Make- Polycab,Finolex, & Mescab)

Meter 55

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

A6) Sub Main wiring by supplying & laying of 1100V

grade 3-1/Cx10 Sq.mm + 2-1/Cx6 Sq.mm for

earthing PVC insulated (FRLS) copper wire through

prelaid PVC concealed conduit in wall with groove

cutting and making good damage to original finish

including supply of necessary sheet metal pull box/

circular box with 5mm thick acrylic sheet cover

(Make- Polycab,Finolex, & Mescab)

Meter 20

A7) Main wiring by supplying & laying of 1100V grade 4

core 25 Sq.mm AL /A cable+ 2 nos 8 SWG GI wire

for earthing through in wall with necessary

termination and clamping or groove cutting and

making good damage to original finish .(Make-

Laser, crystal & Hevell's)

Metre 20

B. DISTRIBUTION BOARDS

[As per Dwg. and Specification]

LIGHTING/ POWER TPN/SPN DISTRIBUTION

BOARD

Supply and Installation of sheet steel (1.2 mm thick)

enclosed, double door, wall mounted Distribution

Boards complete with necessary mounting, internal

wiring and conduiting .(Make- L&T , ABB &.

Hevell"s)

B1) a) Incomer with for (Lights and Raw power ) Nos 1

63A, 415V, 4P, RCCB (100mA) - 1 No.

b) Busbar

415V, 63A, 3 PH, 4W, 50 Hz, 10 KA busbar - 1 No.

c) Outgoing with

6A - 32A, SP MCB (C curve) - 18 Nos.

B2) a) Incomer with for (AC power) Nos 1

63A, 415V, 4P, RCCB - 1 No.

b) Busbar415V, 63A, 3 PH, 4W, 50 Hz, 10 KA busbar - 1 No.

c) Outgoing with

20A - 32A, SP MCB (C curve) - 12 Nos.

B3) a) Incomer with for (UPS power) Nos 1

63A, 240V, DP, MCB - 1 No.

b) Busbar

240V, 63A, 1 PH, 3W, 50 Hz, 10 KA busbar - 1 No.

c) Outgoing with

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

10A - 32A, SP MCB (C curve) - 18 Nos.

C) RECEPTACLES

C1) Supply and Instalation of 16A 240V international

socket (Similer to MK make DW426WHI) with safety

shutter and 16A moduler type switch complete with

M.S. Box and mounting frame with cover

plate.(Make- MK,ABB& similer reputed make)

No. 16

C2) Supply and Instalation of 6A, 5 Pin, 240V

receptacle (RA Type) with safety shutter and One

6A moduler type switch for complete with M.S. Box

and mounting frame with cover plate (Make- MK,&

ABB)

No. 31

C3) Supply and Instalation of 3 no.(Three) 6A, 5 Pin,

240V receptacle (RA Type) with safety shutter and

controlling 6A moduler type switch to be mounted in

board complete with wiring by 1Cx1.5 sqmm PVC

insulated wire (Make- MK,& ABB,similer reputed

make)

No. 11

C4) Supply and Instalation of RJ 12 telephone socket

complete with M.S. Box and mounting frame with

cover plate.(Make- MK,& similer reputed make)

No. 11

C5) Supply and Instalation of RJ 45 computer socket

complete with M.S. Box and mounting frame with

cover plate.(Make- MK ,& ABB )

No. 11

D. CONDUIT

Supplying & laying of PVC conduit to be fixed in wall

/ floor after proper chasing. The wall/floor to be

finished as it was before, after embedding the

conduit. (Make- AKG , PICISION)

D1) i) The following sizes of conduits

a) 20 mm dia Metre 380

b) 25 mm dia Metre 55

D2) Supply and Installation of flexible PVC Conduit of

following sizes :

a) 20 mm dia Metre 25

b) 25 mm dia Metre 15

D3) Supply and installation of medium duty G.I.

Conduit/Pipe of following sizes including all

necessary accessories required for fixing the conduit

on brick wall.(Make- TATA, AKG or other similer

make)

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

a) 25 mm dia conduit/pipe Metre 5

E) MISCELLENEOUS ITEMS

E1) Supply and drawing of DIA 0.5 mm, three pair

Telephone Cable with necessary conection as

required (Make- Polycab,Finolex, or other similer

make)

Meter 50

E2) Supply and fixing TPN 125A SFU with sheet steel

encloser in iron fream with necessary connection

as required (Make- L&T , ABB &.Hevell's)

No 1

E3) Supply and fixing one set of LED/NEON indicator

engage light (yellow, red and green) at out side of

Maneger room with necessary mounting and

connection as required ( Make- Anchor or

other similer make)

No 1

E4) Supply and fixing flush-type power unit complete of

DP MCB,SP starter ( 7A-11.50A), socket & plug with

indicating light with necessary mounting and

connection as required for 1.5 Ton A.C Unit ( Make-

Northwest or other similer make)

No 9

E5) Supply and fixing flush-type power unit complete of

DP MCB,SP starter ( 4.75A-7.50A), socket & plug

with indicating light with necessary mounting and

connection as required for 1 Ton A.C Unit ( Make-

Northwest or other similer make)

No 2

E6) Supply and fixing of 300 mm sweep wall fan with all

necessary mounting and connection as required

(Make- USHA , ORIENT,& similer reputed make)

No 20

E7) Supply and fixing of 300 mm dia exhust fan with

louver and all necessary mounting and connection

as required (Make- USHA , ORIENT,& similer

reputed make)

No 3

E8) Supply and fixing of 1200 mm sweep ceiling fan

with louver and all necessary mounting and

connection as required (Make- USHA , ORIENT, &

CG)

No 2

E9) Supply and fixing of luminaires like Philips make

FBS 470/236 D6 HF (AG) ,2XPL-L 36W lamp with

all necessary mounting & connection as required

(Make- Philips ,Wipro,& CG)

No 32

Item no. Description Unit Quantity Unit Rate Total

(Rs.) (Rs.)

E10) Supply and fixing of luminaires like Philips make

FCS 518/218, 2XPL-L 18W lamp with all necessary

accessaries like ballast ,mounting arrangment &

connection as required (Make- Philips ,Wipro,& CG)

No 22

E11) Supply and fixing TPN 32A MCB (C curve) with

sheet steel encloser(Industrial type) with socket

necessary connection as required ( Make- L&T, ABB

or other similer make)

No 3

E12) Supply and Installation of Earthing System including

cutting, welding as required of following sizes :

A 25 x 6 mm GS flat Mtr. 20

B 8 SWG GI wire Mtr. 20

E13) Supply and laying of 32 mm dia, 3000 mm long G.I

pipe buried vertically in earth below 1000 mm

ground with earth pite as per IS 3043.

Set 2

E14) Supply and fixing telephone Crone 25 pair with

encloser with necessary connection as required

Set 1

E15) Supply and fixing one set of adopter box with sheet

steel encloser, 125A rated AL bus bar (TPN) at

electrical room with necessary mounting and

connection as required (If required).

Set 1

E16) Supply and fixing one set of 125A,4P,change over

switch with necessary mounting and connection as

required.

Set 1

E17) Supply and fixing one set of call bell at out side of

Maneger room with necessary mounting and

connection as required( Make- Anchor or other

similer make)

No 1

TOTAL

GRAND TOTAL

SL. NO. ITEM OF WORKS AMOUNT(RS.)

1 CIVIL WORKS

2 INTERIOR & FURNISHING WORKS

3 ELECTRICAL WORKS

GRAND TOTAL OF ALL ITEMS

SUMMERY OF ALL ITEMS FOR

INTERIOR WORKS OF BANK OF BARODA ,

JALPAIGURI BRANCH.

Estimate for BOB Jalpaiguri Branch Consultant : ALINDA