Before the first use Operating the washing machine Washing Changing the programme sequence Programme chart
OP
ER
ATIN
G T
HE
WA
SH
ING
MA
CH
INE
WA
SH
ING
CH
AN
GIN
G T
HE
PR
OG
RA
MM
E S
EQ
UE
NC
E
WM
V 96
0 W
PS
en -
AU
, NZ
M.-
Nr.
10 3
76 2
40/0
0
Cancelling a programme ĺ Touch the Start/Stop sensor. ĺ Select Cancel programme.
The suds will be pumped away. The pro-gramme will be cancelled and the door lock is released. ĺ Pull open the door. ĺ Remove the laundry.
Selecting another programme ĺ Close the door. ĺ Select the programme you want. ĺ Add detergent to the detergent dispenser drawer, if necessary.
ĺ Press the Start/Stop sensor.The new programme will begin.
Interrupting a programme ĺ Switch the washing machine off with the button.
ĺ Switch the washing machine back on with the button to continue with the same programme.
Adding or removing laundry after a programme has started
You can add or remove items during the first few minutes after the programme has started. ĺ Press the Start/Stop sensor. ĺ Touch the Add laundry sensor.
The programme will stop and the door will unlock. ĺ Pull open the door. ĺ Add or remove items. ĺ Close the door. ĺ Press the Start/Stop sensor.
The programme will continue.
The door cannot be opened if: – the suds temperature is above 55°C. – the water is above a certain level. – the programme has reached the Spin stage.
6. Starting the programme - the end of the programme
Starting the programme ĺ Press the flashing Start/Stop button.
The door will lock and the programme will start.The programme status will appear in the display.
At the end of the programmeThe door is still locked during the Anti-crease phase and the following will appear alternately in the display: Anti-crease and Finished.The following information will also appear: Press the Stop button, then unload the drum.Press the Start/Stop button. The door will be unlocked. ĺ Pull open the door. ĺ Remove the laundry.
ə Check that all items have been remo-ved from the drum.
ĺ Check the folds in the door seal for any small articles, e.g. buttons, which might be lodged there.
ĺ Switch the washing machine off with the button.
ĺ Close the door and remove any used capsules which may be in the detergent dispenser drawer.
Pro
gram
me
Load
(in
kg)
Tem
pera
ture
Item
sEx
tra o
ptio
ns
Co
tto
ns9.
0C
old
to 9
0°C
Cot
tons
, lin
ens
or c
otto
n m
ix fa
bric
s, e
.g. t
able
line
n, to
wel
ling,
un
derw
ear,
T-sh
irts
etc.
,
, ,
, ,
,
Min
imum
iro
n4.
0C
old
to 6
0°C
Syn
thet
ic, m
ixed
fibr
e an
d ea
sy c
are
cotto
n.
, ,
, ,
, ,
Del
icat
es3.
0C
old
to 6
0°C
Del
icat
e ga
rmen
ts m
ade
from
syn
thet
ic fi
bre,
mix
ed fi
bre,
rayo
n an
d vi
scos
e.
, ,
, ,
, ,
Wo
olle
ns
2.0
Col
d to
40°
CM
achi
ne-w
asha
ble
or h
and-
was
habl
e w
ool o
r woo
l ble
nd fa
bric
. If
the
care
labe
l doe
s no
t spe
cify
a te
mpe
ratu
re, w
ash
usin
g th
e co
ld
setti
ng.
Den
im3.
0C
old
to 6
0°C
Text
iles
mad
e fro
m d
enim
.
, ,
, ,
, ,
Shi
rts
2.0
Col
d to
60°
CS
hirt
s an
d bl
ouse
s m
ade
of c
otto
n an
d m
ixed
fibr
e.
, ,
, ,
, ,
Exp
ress
20
3.5
Col
d to
40°
CC
otto
n ga
rmen
ts th
at h
ave
hard
ly b
een
wor
n or
are
onl
y ve
ry li
ghtly
so
iled.
,
,
Qui
ckP
ow
erW
ash
5.0
40°C
to 6
0 °C
Mod
erat
ely
soile
d ga
rmen
ts w
hich
are
als
o su
itabl
e fo
r was
hing
in
the
Cot
tons
pro
gram
me.
,
Aut
om
atic
plu
s6.
0C
old
to 4
0°C
Mix
ed lo
ads
of g
arm
ents
sui
tabl
e fo
r the
Cot
tons
and
Min
imum
iron
pr
ogra
mm
es. S
ort a
ccor
ding
to c
olou
r.
, ,
,
Dar
k g
arm
ents
3.0
Col
d to
60°
CB
lack
and
dar
k ite
ms
mad
e of
cot
ton
or m
ixed
fibr
es.
,
, ,
, ,
, O
uter
wea
r2.
5C
old
to 4
0°C
Perfo
rman
ce o
uter
wea
r (e.
g. ja
cket
s an
d tro
user
s) m
ade
from
m
embr
ane
fabr
ic s
uch
as G
ore-
Tex®
, SY
MPA
TEX®
, WIN
DST
OP-
PER
® e
tc.
,
, ,
, ,
Pro
ofin
g2.
540
°CTr
eatin
g m
icro
fibre
fabr
ic, s
kiw
ear a
nd ta
ble
linen
mad
e fro
m m
ainl
y sy
nthe
tic fi
bres
.
=
Ste
am s
moo
thin
g;
= S
oak;
=
Sho
rt;
= R
inse
hol
d;
= P
re-w
ash,
=
Wat
er p
lus;
=
Add
ition
al ri
nse
hold
An
expl
anat
ion
of fu
rthe
r pro
gram
mes
can
be
foun
d in
the
"Pro
gram
me
char
t" in
the
oper
atin
g in
stru
ctio
ns.
1 Detergent dispenser drawer2 Control panel3 Access to drain filters, drain pumps and
emergency release4 Door5 Access panel for TwinDos containers
ə Before using the machine for the first time, ensure that it is correctly installed and connected. Please read the separate operating instructions supplied with the appliance.
Removing the protective foil and stickersRemove the protective foil from the door and any stickers (if present) from the front of the appliance, the display and the lid. Do not remove any labels (e.g. the date plate) which are visible when you open the door.
Setting the language and the time of day ĺ Set the display language and time of day that will appear in the display (see "Before using for the first time" in the operating instructions).
Running the first programme
The TwinDos unit needs to be activated before running the first programme.
ĺ Please refer to "TwinDos" in the operating instructions.
1 Touch display2 Start / Stop sensor
For starting the programme selected and cancelling a programme once it has started.
3 sensor Provides information about the selected programme.
4 sensor For returning to the main menu.
5 Optical interface6 On/Off button
Touch display and sensorsThe , and Start/Stop sensors, as well as the sensors in the display react to finger-tip contact.
The display can be scratched by pointed or sharp objects, e.g. pens. Only touch the touch display with your fingertips.
Touching the sensors in the display reveals a list of options or a sub-menu and also takes you to another menu.
Main menu After switching on, the main menu will appear in the display. You access all the important sub-menus from the main menu.
7 Programmes For selecting a programme.
8 Favourite programmes You can save up to ten of your own cus-tomised programmes.
9 Washing assistant The Washing assistant guides you step by step so that you can select the opti-mum wash programme for your laundry.
10 Scroll bar The scroll bar indicates that further options or more text follows.
11 Navigation sensors You can use the und sensors to scroll through a list or block of text.
12 Mixed items For washing a few lightly soiled items with different garment care instructions. The washing machine will use the list of items to put together a suitable wash programme.
13 Settings You can alter the washing machine's electronics to suit changing requirements in the Settings menu.
10:30
Programmes
Favourite programmes
Washing assistant
< >7 8 9 10 11
10:30
Mixed items
Settings
< >12 13
Washing environmentally and economically
– To get the most out of your machine, load the maximum dry load for the pro-gramme you are using.
– Use the Express 20 programme for small, lightly soiled loads.
– Modern detergents make it possible to wash at lower temperatures (e.g. 20°C). Washing using lower temperature set-tings will save energy.
– For precise dispensing, use automatic detergent dispensing.
– Selecting the highest possible spin speed for the wash programme will save energy when drying in a tumble dryer afterwards.
2. Selecting a programme ĺ Switch on the washing machine with the button. ĺ Touch the Programme sensor. ĺ Scroll with the or sensor until the programme you want appears in the display.
ĺ Touch the sensor for the programme.First the load will appear and then the display will change to show the standard menu for the programme.
Alternatively you can select a programme via– Favourite programmes,– the Washing assistant,– Mixed items.
3. Selecting programme settings
Temperature and spin speed ĺ Touch the Temperature or Spin speed sensor. ĺ Use – and + to set the required value and confirm with OK.
TwinDos ĺ Touch the TwinDos sensor.
The display will ask you to enter the degree of soiling of the laundry. ĺ Set the degree of soiling with the Light or Heavy sensor and confirm your selection with OK.
– If the Miele 2 Phase System is being used: ĺ Select For white items or For coloured items. – If using other detergents: ĺ Confirm or change the selection.
4. Loading the washing machine
Opening the door ĺ Take hold of the door and pull it
open. The load display will now appear.
ĺ Unfold the laundry and load loosely in the drum.
Closing the door ĺ Make sure that no items are
caught between the door and the seal.
ĺ Shut the door with a gentle swing.The display will ask you to enter the degree of soiling of the laundry. ĺ Set the degree of soiling with the Light or Heavy sensor and confirm your selection with OK.
The dosage display will now appear. ĺ Confirm with OK.
Detergent will not appear if TwinDos or CapDosing has been selected for the main wash cycle.
5. Adding detergentThere are several options for adding deter-gent.
TwinDosIf you selected TwinDos when setting the programme, detergent will be dispensed automatically for this wash programme.
CapDosingIf you selected CapDosing when setting the programme, detergent will be dispensed via the capsule for this wash programme.Three different types of capsule are avail-able: Fabric care (e.g. fabric softener) Additives (e.g. detergent enhancers) Detergent
Detergent dispenser drawerAdd detergent in accordance with the value in the dosage display.
ĺ Pull out the detergent drawer and add deter-gent to the compartments.
Detergent for the pre-wash Detergent for the main wash,
including Soak if selected / Fabric softener, liquid starch or
capsules
See "Detergent" in the operating instruc-tions for more information.
ProgrammeManager ĺ Touch the Prog. manager sensor. ĺ Select the Extra option you want.
Extra options ĺ Touch the Extras sensor. ĺ Select one or several Extra options.
Stains ĺ Touch the Stains sensor. ĺ Select the type of stains from the list.
Switching on Delay start ĺ Touch the Finish at sensor. ĺ Use the – and + sensors to set the time you want and confirm with OK.
CapDosing ĺ Touch the CapDosing sensor.
The types of capsules which can be used with the pro-gramme will appear in the display. ĺ Select the type of capsule you want.
Changing a programme and settings
ProgrammeAfter the start of a programme, it is no longer possible to select a different pro-gramme.
Temperature/Spin speedThe temperature can be changed within the first five minutes, except in the Cottons pro-gramme. The spin speed can be changed right up to the start of the final spin. ĺ Touch the Change sensor. ĺ Touch the Temperature or Spin speed sen-sor.
ĺ Use – and + to set the required value and confirm with OK.
Extra optionsIt is possible to select or deselect certain Extra options up to five minutes after the programme has started.
It is not possible to make any changes to the programme or to cancel it if the safety lock has been activated.
1. Preparing the laundry ĺ Empty all pockets.
ə Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to gar-ments and components in the machine.
Sort the laundry by colour and by care label. Most gar-ments have a textile care label in the collar or side seam. ĺ Pre-treat stains and badly soiled areas (see the booklet "Miele's guide to laundry care").
3 5
1 2
4
Quick Start GuideWashing machine
en - AU, NZ M.-Nr. 10 376 240CLE
AN
ING
AN
D C
AR
E
PR
OB
LEM
SO
LVIN
G G
UID
E
PR
OG
RA
MM
EM
AN
AG
ER
/EX
TRA
OP
TIO
NS
/DE
TER
GE
NT
ProgrammeManager/Extra options Detergent Cleaning and care Problem solving guide
These short instructions are not a substitute for the operating instructions supplied with the appliance. Please read the operating instructions supplied with your washing machine before using it for the first time and take note of the Warning and Safety instructions, as well as the full descriptions on how to use your appliance.
Cleaning the detergent dispenser drawer
Washing at low temperatures and the use of liquid detergent can lead to a build-up of mould and bacteria in the detergent dispenser drawer.
ĺ Clean the entire drawer at regular inter-vals for hygiene reasons, even if you are using the TwinDos system exclusively.
ĺ Pull out the detergent dispenser drawer until a resistance is felt.
ĺ Press down the release button and, at the same time, pull the drawer right out of the machine.
ĺ Clean the detergent drawer with warm water.
Cleaning the siphon tube and the fabric softener channel
ĺ Pull the siphon out of the compartment and clean it under warm running water.
ĺ Clean the siphon tube in the same way. ĺ Refit the siphon.
ĺ Clean the fabric softener channel using a brush and warm water.
ə Liquid starch can cause the siphon to become clogged. Make sure that you clean the siphon and siphon tube particu-larly thoroughly after using liquid starch a few times.
Cleaning the detergent dispenser drawer housing
ĺ Use a bottle brush to remove deter-gent residues and limescale from the jets inside the detergent dispenser drawer housing.
The right amount to dispense will depend on the following: – The soiling level of the laundry.
Lightly soiled: No visible dirt or stains. Possibly slight body odour.
Normally soiled: Visibly dirty and / or just a few slight stains.
Heavily soiled: Soiling and / or stains clearly visible.
– The quantity of the laundry. – The water hardness level in your area.Check with your local water supplier if you do not know the hardness level in your area.
ProgrammeManagerThe ProgrammeManager option can be used to customise the washing program-mes to suit your requirements.
IntensiveFor hard-wearing laundry that is very hea-vily soiled. Cleaning efficiency is increased through more intense mechanical action and the application of more heat energy.
ECOThis option reduces energy consumption whilst maintaining cleaning efficiency. This is achieved by increasing the wash duration and at the same time reducing the wash temperature selected.
Extra gentleThis option decreases mechanical action in order to reduce creasing.
Extra quietThis option reduces noise levels during the programme. Use this if you want to wash during quiet periods (for instance, when children are sleeping). The machine will acti-vate the "Rinse hold" option and not spin. The programme duration is longer.
AllergoWashThis option should be used where high standards of hygiene are required. More energy is used to lengthen temperature holding times and more water is used to increase rinsing efficiency. The items must be suitable for drying in a tumble dryer and suitable for ironing .
Extra options
Steam smoothing Steam is injected into the drum at the end of the wash process. Reducing the maxi-mum load by 50% will give a better result. The garments must be suitable for drying in a tumble dryer and suitable for iron-ing .
SoakFor heavily soiled and stained items with protein stains.
ShortFor light soiling with no visible staining.
Rinse holdThe laundry is not spun after the final rinse and remains in the final rinse water. This helps prevent creasing if the laundry is not going to be removed from the drum imme-diately after the end of the programme.
Pre-washFor laundry with large amounts of dirt, e.g. dust and sand.
Water plusThe water level in the main wash and the rinses will be increased if the Water plus Extra option is selected.
Extra rinseAn additional rinse cycle can be carried out to give a better rinse result.
Miele recommended detergents
Programmes
Miele UltraPhase
1/2Miele
Cap Miele
Cap Miele
Cap
Cottons –
Minimum iron –
Delicates – –
Woollens – – –
Denim – –
Shirts –
Express 20 – –
QuickPowerWash – – –
Automatic plus –
Dark garments – – = Recommended; – = Not recommended = WoolCare; = Fabric softener; = Booster
Dispensing fabric softener and liquid starch at the end of the programme
You can dispense fabric softener either by using automatic dispensing or via the deter-gent dispenser compartment.
Automatic dispensingOne of the automatic dispensing containers must be filled with fabric softener. ĺ Select TwinDos. ĺ Select the degree of soiling level of the load.
The display will change to show the Select agent menu. ĺ Make sure that Fabric softener is marked and confirm the selection with the OK sensor.
Fabric softener will be dispensed in the last rinse.
Manual dispensing
ĺ Add the fabric softener or liquid starch to the compartment or insert the appro-priate capsule. Do not exceed the maxi-mum level mark.
It will be automatically dispensed in the final rinse. At the end of the programme a small amount of water remains in the fabric soft-ener compartment.
If starching frequently, thoroughly clean the dispenser compartment, especially the siphon tube, regularly.
Cleaning the drum (Hygiene info)Washing at low temperatures and/or using liquid detergent can cause bacteria and unpleasant odours to build up in the wash-ing machine. Use the Clean machine pro-gramme to clean the machine. Run this programme regularly or at the latest when the Hygiene info: Start a programme with a minimum temperature of 75°C message appears in the display.
To switch off the fault messages: Switch the washing machine off with the button.The messages will appear at the end of the programme and when the washing machine is switched on and need to be confirmed with the OK sensor.Problem/Fault message Possible cause and remedyThe display remains dark, and the Start/Stop but-ton indicator light does not come on.
There is no power to the machine. ĺ Check whether the mains plug is plugged in and swit-ched on.
ĺ Check whether the fuse or mains circuit breaker has tripped.
The washing machine has switched off automatically to save energy. ĺ Switch it back on with the button.
You are asked to enter a code.
Access via a code has been activated. ĺ Enter the code and confirm the entry. Deactivate the code if you do not wish this message to appear in the display the next time the machine is switched on.
The following appears in the display:
Door lock
The door is not closed properly. The door lock could not engage. ĺ Close the door again. ĺ Start the programme again. If the fault message appe-ars again, contact Miele.
The following appears in the display:
Drainage fault
The water outlet is blocked or restricted. The drain hose has been fixed too high. ĺ Clean the filters and the pumps. ĺ Check whether the maximum delivery height of 1.8 m has been exceeded.
The following appears in the display:
Water intake fault
The water inlet is blocked or restricted. ĺ Check whether the tap is turned on properly. ĺ Check whether the inlet hose is kinked. ĺ Check whether there is sufficient water pressure.
The filter in the water inlet is blocked. ĺ Clean the filter (see the operating instructions).
The following appears in the display:
Technical fault F
There is a fault. ĺ Restart the programme. If the fault message appears again, contact Miele.
The following appears in the display:
Waterproof system reacted
The water protection system has reacted. The washing machine is switched off. ĺ Turn off the tap. ĺ Call Miele.
Problem/Fault message Possible cause and remedyThe following appears in the display at the end of the programme:
Hygiene info: Start a pro-gramme with a minimum tempe-rature of 75°C
A programme of at least 75°C has not been run for a long period of time. ĺ In order to prevent bacteria and unpleasant odours buil-ding up in the machine, run the Clean machine pro-gramme using Miele dishwasher and washing machine cleaner or powder detergent.
The following appears in the display at the end of the programme:
Insert a new cartridge or fill con-tainer 1
or
Insert a new cartridge or fill cont-ainer 2. Check the wash result
The TwinDos container (or containers) is empty. ĺ Fill the container or containers with liquid detergent or fabric softener or replace the cartridge(s).
ĺ Check if the laundry is clean. There may not have been enough detergent used.
ĺ Wash the items again if necessary.
The following appears in the display at the end of the programme:
Intensive flow: Clean the filter and jet nozzle or remove foreign objects from the pump housing
The pumps are dirty. ĺ Clean the pumps as described in "Problem solving guide - Opening the door in the event of a blocked drain outlet and/or power failure" in the operating inst-ructions.
ĺ Start the programme again after cleaning.The jet in the top of the door ring is blocked with fluff. ĺ Remove the fluff with your finger. Do not use any sharp or pointed tools to do this.
ĺ Start the programme again after cleaning.If the fault message appears again, contact Miele. The washing machine can still be used but with reduced fun-ctionality.
Extra cooling appears in the display after a programme has been cancelled.
For safety reasons, the door cannot be opened if the suds temperature is higher than 55°C. ĺ Wait until the temperature in the drum has decreased and the message has gone out in the display.
Cleaning the TwinDos system
The washing machine has a cleaning pro-gramme for cleaning the TwinDos system containers and the hoses inside the wash-ing machine.
The TwinDos containers (optional acces-sory) are required to carry out cleaning.
ə If the system has not been used for a long time (more than two months), the detergent in the hoses can become vis-cous. The hoses could become blocked and would then need to be cleaned by a service technician. Clean the TwinDos system every time you change brand of liquid detergent or fabric softener or if the system has not been used for a long period of time.
Starting the maintenance programmeThe maintenance programme is located in the Settings menu under TwinDos. ĺ Follow the instructions in the display and refer to the relevant section in the operat-ing instructions.
After cleaning you can fill one or both con-tainers with new liquid detergent and/or fabric softener.
Cleaning the compartmentDetergent residue can cause clogging. ĺ Use a damp cloth to clean the compart-ment interior when you change the car-tridge or container.