-1-1038245-T01-B
BEFORE YOU BEGINBEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
DROP-IN AND FREESTANDING BATHK-11343T / K-11344T
ã
ã
, 2004
Copyright Kohler China Ltd., 2004
· Turn off the water supply.
The plumbing installation must comply with all localwater supply and building regulations.
Before installation carefully inspect the new fixturefor any signs of damage.
·
·
·
·
·
Please read these instructions carefully tofamiliarize yourself with the required tools, materials,and installation sequences. Follow the sections thatpertain to your particular installation. This will helpyou avoid costly mistakes. In addition to properinstallation, read all operating and safety instructions.
All information is based on the latest productinformation available at the time of publication.Kohler China Ltd. reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.
These instructions contain important care, cleaning,and warranty information-please leave theseinstructions for the consumer.
·
·
·
·
·
·
DESCRIPTION
This manual covers the installation of the Escale
freestanding and drop-in baths.
SAFETY: WARNINGS
Kohler products are precision-engineered and shouldgive continued superior and safe performance,provided:
1. They are installed, commissioned, operated andmaintained in accordance with the recommendationsgiven in this Manual.
2. Periodic attention is given, as necessary, to maintainthe product in good functional order. Recommendedguidelines are given in the section.
Carefully inspect the new fixture for any signs ofdamage.
When installing Kohler Products, manufacturersguidelines for power tool safety should be followed.
MAINTENANCE
1.
2.
ORDERING INFORMATION
Accessories/Hardware
Drain 17295T-CP
/
17295T-CPOptional
-2-
ROUGHING-IN
Unit: mm
K-11344T
52 +3- 2
879
893
440
1785
1929
1220
1630
135 5276
341
413456
355
660
524
1075 5
615 5
77 2
635 5
530 5
52
+0- 7
+3- 2
+0- 5
+0- 3
+0- 5
+-
+-
+-
+-
+-
+-
Freestanding Bath
K-11343T
886
893
443
1787
1929
355
60 80
341413456477
524
Min
i=
10
0M
axi=
21
0
Mini = 510Maxi = 620
276320
+0- 5
+0- 5
+0- 3
52+3- 2
52
+0-50 320
+0-50
+0- 7
+3- 2
16301220
660
77 2+-
Drop in Bath
1038245-T01-B
: 52
Diameter of overflow hole: 52
: 52
Diameter of overflow hole: 52
: 52
Diameter of drain hole: 52
: 52
Diameter of drain hole: 52
SPECIFICATION
Product Information
Some of the baths included in this guide are suitable fortwo bathers. The floor must be able to support thecombined weight of the bath, the water and two bathers.
-3-
INSTALLATION
Installing the Feet (Drop-in Bath)
1. Install the cross bar onto the bottom of the bath byfeeding it through the bracket.
2. Make sure the cross bars are evenly spaced aboutthe centre of the bath and secure them in positionwith the bolts.
3. Install the feet onto the cross bars and secure themin position with the nuts.
( )
1.2.
3. P4142010
Nuts
Cross Bar
Feet
Threaded Bar
Bolt
Bracket
Preparing the Bath for Installation (Drop-inBath)
1. If required, use the installation template (supplied) tomark the positions of the holes for the taps and drillwith a suitable tool.
We recommend that the hot and cold watersupplies are installed with isolating valves.
2. Fit the taps and waste onto the bath in accordancewith the manufacturer
,s instructions.
Note!
3. Position the bath in the desired location and makesure that it is level. Adjust the bathtub to obtain aheight of 510 mm minimum and 620 mm maximumbetween the floor and the rim of the bath.
The feet can be adjusted to make sure that thebath is level.Note!
( )
1. ( )
2.3.
510~620
Spirit Level
Adjustable Feet
Template
Waste
P4158020
P4158030
AdjustableFeet
320+0-50
Mini: 510mmMaxi: 620mm
320+0-50
1038245-T01-B
-4-
Installing the Bath (Drop-in Bath )
1. Construct a stud frame designed for your particularinstallation. Use the dimensions in the diagramabove when constructing your frame.
When constructing the frame make sure that youinclude service panels. These are required formaintenance of the valve and waste assemblies.
Note!
Note!
Note!
For drop-in baths without a ledge at least a 2 mmgap must be left between the top of the wall and the rim.Do not support the bath on the rim.
2. Carefully position the bath into the recess.
Either finish the top surface of the framestructure before dropping the bath in, or level the bathleaving enough gap between the top surface and thebath rim to slide tiles under.
1.
2
2.
Service Panel
1740mm
840mm
Finish the Installation (Drop-in Bath)
1. Ensure that all the connections are tight.2. Turn on the water supply and check for any leaks.3. Cover the bath frame with water-resistant material in
accordance with the manufacturer s instructions.,
( )
1.2.3.
P4158050
Bath
StudFramework
Silicone Sealant
Ledge
Finished WallMaterial
Water ResistantWall Board
min 2mm2
1038245-T01-B
P4142010
-5-1038245-T01-B
4. Install the finished wall surface in accordance with
the manufacturer s instructions.
5. Apply a bead of silicone sealant between the bath
and the finished wall surface.
6. Remove the packing pieces from the top of the bath.
7. Remove any excess sealant.
8. Fit the pillow.
,4.
5.
6.
7.
8.
Preparing the Bath for Installation(Freestanding Bath)
1. Remove the bolts and washers that attach the apronto the bath.
2. Remove the apron.
( )
1.
2.
Bolt
Washer
P4158070
3. Place the apron in position on the floor and, using apencil draw around the inside surface of the apron.
3.
P4158080
Apron
140mm90
-6-
4. Position the bath in the desired location and make
sure that it is level. Adjust the bath to obtain a height
of between 635 5mm between the floor and the top
rim of the bath, please refer to the dimensions on
page 5.
The feet can be adjusted to make sure that the
bath is level.
Note!
4.
635 5
P4158090
Spirit Level
5. Using a pencil, mark the positions of the floor clampson the floor.
5.
P4158100
Floor Clamp
1038245-T01-B
6. Lift the bath and remove the floor clamps from therods.
6.
7. Put the floor clamps in the marked positions on the
floor and fix them in position with the floor plugs and
the screws.
Make sure that you avoid hidden
cables and pipes when drilling holes in the floor
or wall.
Caution!
7.
Floor Clamp
Screws
Floor Plugs
Rod
Floor Clamp
P4158110
P4158120
x4x8
4x30
x8
O6
-7-1038245-T01-B
8. Use the installation template (supplied) to mark the
positions of the holes for the taps and drill with a
suitable tool.
We recommend that the hot and cold water
supplies are installed with isolating valves.
9. Fit the taps and waste onto the bath in accordance
with the manufacturer s instructions.
Note!
,
8. ( )
9.
Template
Waste
P4158125
P4158130
-8-1038245-T01-B
Installing the Bath (Freestanding)
1. Rest the bath in an upside down position using two
chairs for support.
2. Carefully install the apron and secure in position at
each end with the washers and the bolts. Do not use
a drill for this procedure.
( )
1.
2.
Tighten by hand
Bolt
Washer
Ok No
5. Lift the bath up slightly and remove the blocks.Lower the bath back onto the floor clamps, makingsure that they engage correctly in the floor clamps.
5.
6. Use a screwdriver to lock the floor clamps.
Don t use the apron to support the bath.Note!,
6. ( )
Floor ClampProtectors
3.
4.
( )
3. Support the bath on two blocks of wood making sure
that the rods on the legs locate directly above the
floor clamps.
4. Connect the services to the bath.
Note! The flexible waste pipe (supplied) and flexible
inlet connectors should be used.
P4158150
Wooden Block
Rod
Floor Clamp
P4158160
-9-
Floor Clamp
Wooden Block
Waste
Water Supply
P4158140
x2
1038245-T01-B
-10-
Cleaning
Caution! Risk of product damage. Many
cleaners contain abrasive and chemical
substances, and should not be used for cleaning
stainless steel, enamel, plated or plastic fittings.
These finishes should be cleaned using a mild
washing up detergent or soap solution, rinsed
and then wiped dry with a soft clean cloth.
LIMITED ONE-YEAR WARRANTYLIMITED ONE-YEAR WARRANTY
Plumbing Fixtures and Fittings LimitedOne-year Warranty
Kohler plumbing fixtures and fittings are warrantedto be free of manufacturing defects.
This product is warranted for one year from date ofpurchase. Kohler China will be responsible for anyproblems caused by manufacturing defects providedwith the invoice. Kohler China will, at its election,repair, replace or make appropriate adjustmentwhere Kohler China inspection discloses any suchdefects occurring in normal usage within one yearafter purchase.
Implied warranties including that of merchantabilityand fitness for a particular purpose are expresslylimited in duration to the duration of this warranty,Kohler China disclaims any liability for special,incidental or consequential damages. Damages tothe product caused by misuse, abuse andinstallation that is not in accordance with theowner's manual are not covered by this warranty.
To obtain quick warranty service, please contactyour dealer, or write to Kohler China. (Original salesreceipt must be provided as the proof of purchase.)
Kohler China Investment Company Ltd.Central Customer Service Center19/F, Shanghai Square, 138 Huai HaiRoad, Luwan District, Shanghai, PRCZip Code: 200021
This is our exclusive written warranty.
·
·
·
·
USER MAINTENANCEUSER MAINTENANCE
·
·
·
·
()
( )
13819
200021
Finish the Installation (Freestanding Bath)
1. Ensure that all the connections are tight.2. Turn on the water supply and check for any leaks.3. Remove the packing pieces from the top of the bath.4. Fit the pillow.
( )
1.2.3.4. P4158170
Pillow
1038245-T01-B