Date post: | 11-Mar-2018 |
Category: |
Documents |
Upload: | doannguyet |
View: | 264 times |
Download: | 1 times |
A fully mechanized rock bolting rig for bolt lengths from 1.5-3.5 m heightsup to 9.5 meters
BOLTEC M
A FULLY MECHANIZED ROCK BOLTING RIG FOR BOLT LENGTHS FROM 1.5-3.5 METERS. EFFECTIVE IN ROOF HEIGHTS UP TO 9.5 METERS.
MAIN BENEFITS
Productivity The Mechanised Bolting Unit (MBU) utilises a single feed rail concept that means that the unit never moves off the drilled bolt hole - this maximises the hole alignment capabilities when installing the bolt and ensures faster installation times.
Rock Drill The COP 1132 rock drill is optimised for bolt hole drilling, with it’s light weight and high frequency it reduces loads on the boom whilst achieving superior penetration rate. For larger hole diameters required for some friction bolt types or harder rock conditions the optional COP 1435 delivers the hitting power needed to get the job done.
Carrier Commonality The Boltec M-series machines share a common four wheel drive articulated carrier design with their Simba M/E and Boomer M/E stablemates. With an open service architechture philosophy it allows for fast and easy maintenance.
BOLTEC M MAKING MINING SAFE
2
+ SAFETY Mechanised bolting removes the operator from the potential danger
area of unsupported ground. All drilling and bolt installation is controlled from the operator station under a FOPS canopy or optional ROPS/FOPS air
conditioned cabin.
+ BOLT INSTALLATION QUALITYMechanised bolting typically holds a much higher installation quality and
consistency than manual or semi-mechanised installation. Bolt angles, bolt spacing, controlled grout ratios, installation pressures, and bolt
numbers are just some of the data that can be collected or recorded.
+ OPERATOR COMFORTThe operator position affords excellent visibility of the bolting operation
as well as when tramming the vehicle. The operator area is spacious and features a swingable operator seat for driving and bolting. The optional
ROPS/FOPS air conditioned cabin enhances the operator’s comfort especially in extreme temperatures or dusty conditions.
BOLTEC M
SAFE BOLTINGSAFETY AND QUALITY OF BOLT INSTALLATION IS OUR FOCUS. THE BOLTEC M IS DESIGNED WITH STANDARD AND OPTIONAL FEATURES THAT ENSURE THESE GOALS ARE MET.
ATLAS COPCO SERVICE– IT’S NOT JUST ABOUT OUR PROMISES, IT’S ABOUT DELIVERYWe offers several levels of service agreements to meet the requirements of your operation and to se-cure your productivity. Our service agreements help you build a quality operation focused on proactive, planned maintenance to minimize unplanned down-time. We support maintenance with detailed parts information on every piece within our full inventory of components, accessories, and tools.
4
BUT 35HBE
Automatic boom lubrication system, rear part
Central boom lubrication kit
Ni-Cr boom cylinders for corrosive conditions
COP 1132
COP 1435
Rock drill lubrication, air dryer system
Air-water mist flushing, external water, internal air, hydraulic oil cooled by air fan
Air-water mist flushing, external water, internal air, hydraulic oil cooled by water
Air-water mist flushing, internal water, internal air, hydraulic oil cooled by air fan
Rock drill lubrication warning kit
Hole blowing kit
ROCK DRILL A B
TECHNICAL SPECIFICATIONS
Total installed power 63 kW (Auto cement, 83 kW)
Main motors 55 kW (Auto cement, 75 kW)
Voltage 380-1 000 V
Frequency 50Hz
Frequency 60 Hz
Soft start (380–690 V)
Transformer 8 kVA
Electronic overload protection for electric motors
Digital volt/ampere meter in electrical cabinet
Phase sequence and eart fault indicator
Battery charger
Cable reel with limiting switch
Electrical outlet, main supply voltage 16Amp 3-phase (16A or 32A socket size) - not for 1000V
Extra transformer 3-phase 15kVA capacity with 230V and 400V outlet (16A or 32A socket size)
PC4 or PC5 Plug/Socket
Spotlight, 1x70 W, 24 V
Illuminated stairs for platform (LED)
ELECTRICAL SYSTEM A B
BOOM A B
BOLTING UNIT A B
Compressor: Atlas Copco GAR5
Hydraulic water booster pump capacity at 7 bar, 80 l/min
Minimum water inlet pressure 2 bar
Water flow and pressure guard for flushing water
Water hose reel, including water hose
High pressure washing kit
AIR/WATER SYSTEM A B
Deutz TCD 2013 L4 120kW 4 cylinder Tier 3 / Stage IIIA diesel engine
Deutz TCD 4.1 115kW 4 cylinder Tier 4 final / Stage IV diesel engine
Articulated ±40° steering angle
Four wheel drive
Hot climate tramming kit
Electrical system 24 V
Batteries 2 x 125 Ah
Automatic differential lock on front axle, limited slip
Tyres, 12.00 R24
Clearance outside axles rear 13°
Front and rear hydraulic jacks
Fuel tank volume 4 cylinder engine 110 L
Central lubrication system
Tramming lights, rear 4 x 40W LED
Tramming lights, rear 2 x 40W LED + 2 x 70W Halogen
Working lights 2 x 320W LED 24V DC
Illuminated stairs for platform
Central grease point
Fire extinguisher
Fire suppression system ANSUL -manual release
Fire suppression system ANSUL -Automatic release (checkfire)
Fire suppression system ANSUL - Automatic release with CO2 in electrical cabinet
CARRIER A B
Mechanical bolting unit
Magazine capacity 10 bolts
Size of face plates, rectangular, diameter, max 150x150 mm
Size of face plates, round, diameter, max Ø 200 mm
Bolt length from 1.5 m to 3.5 m
Swellex, Mn 12, Mn 16, Mn 24
Split-Set, SS39, SS46
Mechanical anchor bolts, CT, Kiruna, including boltrotator
Rebar - manual resin / cement cartridge, including boltrotator
Rebar - resin cartridge injection system, automatic, including boltrotator
Rebar - Cement injection system, manual mixing
REbar - Cement injection system, automatic mixing with bulk cement silo 1 000 kg
Hose injection system for resin cartridges
Dual bolt lengths*
Dual bolt types
Extension drilling kit
Screen handling arm
*2nd bolt length no less than 70% length of maximum bolt length
Low oil level indicator
Oil temperature meter
Filtration 16 μm
Oil filter indicator
Mineral hydraulic oil
Electric oil filling pump
Biodegradable hydraulic oil
Hydraulic oil thermostat
Hydraulic oil leakage detection and shut-down system
Hydraulic oil fine particulate and water filtration system (not in conjunction with bulk cement system)
HYDRAULIC SYSTEM A B
Rig Control System (RCS)
Bolt quality log (BQL)
Bolt plan navigation
Rig Remote Access (RRA)
Bolt angle indication
Direct Hydraulic Control System (DCS)
CONTROL SYSTEM A B
A = BOLTEC M C = OPTION B = BOLTEC M D = STANDARD
5
Total 21 600 kg
Boom side 15 500 kg
Engine side 6 700 kg
WEIGHT
Width 2 245 mm
Height, Cabin fixed ROPS/FOPS 3 021 mm
Height, Protective roof (min/max) 2 361/3 061 mm
Length tramming MBU34.3 13 937 mm
Ground clearence 254 mm
Turning radius outer/inner 6 600/4 100mm
DIMENSIONS
Voltage Dimension, mm2 Diameter, mm Length
400V 3x185+3G35+2x1x1.5 56 mm 90 m
440V 3x150+3G25+2x1x1.5 52 mm 100 m
460-500V 3x120+3G25+2x1x1.5 46.5 mm 120 m
500-550V 3x95+3G16+2x1x1.5 42 mm 150 m
660-690V 3x70+3G16+2x1x1.5 37 mm 180 m
1000V 3x50+3G10+2x1x1.5 32 mm 200 m
Recommendations are given for surrounding temperature of 40°C
RECOMMENDED CABLE SIZES AND LENGTHS
FOPS/ROPS approved cabin, noise level <80 dB(A)
Low profile cabin ROPS/FOPS 150 mm lower than standard - seated operation only
Low profile cabin ROPS/FOPS 150 mm lower than standard - seated operation only
Cabin height fixed, lowered 140 mm from standard
Cabin height fixed, raised 250 mm from standard
Mediaplayer
12 V outlet for communication radio
Reversing camera with monitor
Air conditioning unit
Heating function for air conditioning (water transferred)
Swingable seat for drilling and tramming
Cabin body made of stainless steel
Joystick-controlled spotlights left and/or right, 70 W
Front window, 24 mm
FOPS-approved grizzly bar for front window
Cabin lift/tilt function (FOPS)
OPTIONAL CABIN A B
On flat ground (Rolling resistance 0.05) >15
On incline 1:8 >5
TRAMMING SPEED
TECHNICAL SPECIFICATIONSA = BOLTEC M C = OPTION B = BOLTEC M D = STANDARD
Mounting height increased 60mm from standard
Mounting height increased 310mm from standard
PROTECTIVE ROOF A B
6
3 262
20°
30°R 6
600
R 1
500
R 4 100
41°
R 7 050
1 2401 240
3 2623 712
9 39
02
230
4 91
3
2 508
3 49
0
EC
www.atlascopco.com
EC
2 105 801
2 661 4 940
4 838
1 430
2 000
13 937
Ø1 238
2 45
057
1
1 19
7
1 940 792
19°10°13°
139
TECHNICAL SPECIFICATIONS
Dimension illustration (Optional equipment mounted).
Coverage area (2.4 m bolts).
Turning radius.
7
COMMITTED TO SUSTAINABLE PRODUCTIVITY
We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time.This is what we call – Sustainable Productivity.
www.atlascopco.com
98
51 22
02 01i 2
016 Öre
bro, S
we
den
. Le
gal N
otice © C
opyrig
ht 2014
, Atlas C
op
co Ro
ck Drills A
B, Ö
reb
ro, Sw
ed
en. A
ll pro
du
ct nam
es in this pu
blicatio
n are tradem
arks of Atlas C
op
co. Any un
auth
orize
d use or co
pying
of the contents o
r any part there
of is pro
hibite
d. Illustratio
ns and p
hoto
s may sh
ow e
quip
ment w
ith optio
nal extras. N
o warranty is m
ade re
gard
ing sp
ecifi
cations o
r otherwise. S
pe
cificatio
ns and e
quip
ment are su
bje
ct to ch
ang
e with
ou
t notice. C
onsult yo
ur Atlas C
op
co Custo
mer C
enter for sp
ecifi
c inform
ation
.